arm64: dts: qcom: msm8916/39-samsung-a2015: Add flash LED
PATCH 1/1 arm64: dts: qcom: msm8916/39-samsung-a2015: Add flash LED
The phones listed below have Richteck RT5033 LED, which has GPIO pin configurations similar to SGM3140 Flash LED driver.
Add it to the device trees.
- Samsung Galaxy A3/A5/A7 2015
- Samsung Galaxy E5/E7
- Samsung Galaxy Grand Max
--- .../qcom/msm8916-samsung-a2015-common.dtsi | 23 +++++++++++++++++++ .../boot/dts/qcom/msm8939-samsung-a7.dts | 23 +++++++++++++++++++ 2 files changed, 46 insertions(+)
arch/arm64/boot/dts/qcom/msm8916-samsung-a2015-common.dtsi +23 -0
@@ -4,6 +4,7 @@ #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/input/input.h> #include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/leds/common.h> #include <dt-bindings/pinctrl/qcom,pmic-gpio.h> / {
@@ -36,6 +37,21 @@ clk_pwm: pwm { status = "disabled"; }; + flash-led-controller { + compatible = "richtek,rt5033-led"; + enable-gpios = <&tlmm 34 GPIO_ACTIVE_HIGH>; + flash-gpios = <&tlmm 36 GPIO_ACTIVE_HIGH>; + + pinctrl-0 = <&camera_flash_default>; + pinctrl-names = "default"; + + flash_led: led { + function = LED_FUNCTION_FLASH; + color = <LED_COLOR_ID_WHITE>; + flash-max-timeout-us = <544000>; + }; + }; + gpio-keys { compatible = "gpio-keys";
@@ -293,6 +309,13 @@ accel_int_default: accel-int-default-state { bias-disable; }; + camera_flash_default: camera-flash-default-state { + pins = "gpio34", "gpio36"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + fg_alert_default: fg-alert-default-state { pins = "gpio121"; function = "gpio";
arch/arm64/boot/dts/qcom/msm8939-samsung-a7.dts +23 -0
@@ -7,6 +7,7 @@ #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/input/input.h> #include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/leds/common.h> / { model = "Samsung Galaxy A7 (2015)";
@@ -31,6 +32,21 @@ tz-apps@85500000 { }; }; + flash-led-controller { + compatible = "richtek,rt5033-led"; + enable-gpios = <&tlmm 34 GPIO_ACTIVE_HIGH>; + flash-gpios = <&tlmm 36 GPIO_ACTIVE_HIGH>; + + pinctrl-0 = <&camera_flash_default>; + pinctrl-names = "default"; + + flash_led: led { + function = LED_FUNCTION_FLASH; + color = <LED_COLOR_ID_WHITE>; + flash-max-timeout-us = <544000>; + }; + }; + gpio-hall-sensor { compatible = "gpio-keys";
@@ -360,6 +376,13 @@ accel_int_default: accel-int-default-state { bias-disable; }; + camera_flash_default: camera-flash-default-state { + pins = "gpio34", "gpio36"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + fg_alert_default: fg-alert-default-state { pins = "gpio121"; function = "gpio";
Signature · 1 line
2.39.2
Quoted 10 lines · Raymond Hackley
The phones listed below have Richteck RT5033 LED, which has GPIO pin configurations similar to SGM3140 Flash LED driver.
Add it to the device trees.- Samsung Galaxy A3/A5/A7 2015
- Samsung Galaxy E5/E7
- Samsung Galaxy Grand MaxSigned-off-by Raymond Hackley <[email protected]>---
What about the other subdevices registered with the RT5033 MFD?
Konrad
Hi Konrad,
Quoted 1 line
What about the other subdevices registered with the RT5033 MFD?
Currently the MFD is not able to control the flash LED, due to missing driver for it.
Alternatively we control it with GPIO pins. With driver leds-sgm3140, the binding is not under the RT5033 MFD.
Regards,
Raymond
Quoted 8 lines · Raymond Hackley
Hi Konrad,
Quoted 1 line
What about the other subdevices registered with the RT5033 MFD?
Currently the MFD is not able to control the flash LED, due to missing driver for it.
Alternatively we control it with GPIO pins. With driver leds-sgm3140, the binding is not under the RT5033 MFD.
Hm.. I have mixed feelings..
Does the led controlled onboard this chip have some super complex functionality that is going to be exposed through a specific driver and that is not exposed through the sgm3140 driver?
Konrad
Hi Konrad,
Quoted 9 lines · Konrad Dybcio
Quoted 8 lines · Raymond Hackley
Hi Konrad,
Quoted 1 line
What about the other subdevices registered with the RT5033 MFD?
Currently the MFD is not able to control the flash LED, due to missing driver for it.
Alternatively we control it with GPIO pins. With driver leds-sgm3140, the binding is not under the RT5033 MFD.
Quoted 5 lines
Hm.. I have mixed feelings..
Does the led controlled onboard this chip have some super complex functionality that is going to be exposed through a specific driver and that is not exposed through the sgm3140 driver?
The rt5033-led&sgm3140 situation was discussed in msm8916-mainline matrix room before, here is a summary for list.
Using the full rt5033-led driver (old patchset here [1]) has some benefits, like:
* led can have different intensity levels
* led can (supposedly) be used in strobe mode
Using sgm3140 driver mostly works fine, but there could potentially be situations where led stops working and a reboot to stock android kernel is required to get it working again. So far that has only been reproduced by first booting a kernel with full rt5033-led driver (based on [1]), and then booting a kernel using sgm3140 driver instead.
[1] https://lore.kernel.org/linux-leds/[email protected]/
Best regards,
Henrik Grimler
Quoted 26 lines · Henrik Grimler
Hi Konrad,
Quoted 9 lines · Konrad Dybcio
Quoted 8 lines · Raymond Hackley
Hi Konrad,
Quoted 1 line
What about the other subdevices registered with the RT5033 MFD?
Currently the MFD is not able to control the flash LED, due to missing driver for it.
Alternatively we control it with GPIO pins. With driver leds-sgm3140, the binding is not under the RT5033 MFD.Quoted 5 lines
Hm.. I have mixed feelings..
Does the led controlled onboard this chip have some super complex functionality that is going to be exposed through a specific driver and that is not exposed through the sgm3140 driver?
The rt5033-led&sgm3140 situation was discussed in msm8916-mainline matrix room before, here is a summary for list.
Using the full rt5033-led driver (old patchset here [1]) has some benefits, like:
* led can have different intensity levels
* led can (supposedly) be used in strobe mode
Quoted 8 lines
Using sgm3140 driver mostly works fine, but there could potentially be situations where led stops working and a reboot to stock android kernel is required to get it working again. So far that has only been reproduced by first booting a kernel with full rt5033-led driver (based on [1]), and then booting a kernel using sgm3140 driver instead.
2015, whoops..
Looks like the reviewers were mostly happy (style comments for the most part), so perhaps it'd be worth to bring it back?
As for this patch, I'll be happy to take it if you can confirm the rt5033-leds driver won't require bindings changes (i.e. the node you're adding today would work fine as-is if you removed sgm3140 and probed the separate driver), at least in the form that it was posted in the link above..
Konrad