PCI: hotplug: Add extension driver for Ampere Altra hotplug LED control
PATCH 1/1 PCI: hotplug: Add extension driver for Ampere Altra hotplug LED control
On Ampere Altra, PCIe hotplug is handled through ACPI. A side interface is also present to request system firmware control of attention LEDs. Add an ACPI PCI Hotplug companion driver to support attention LED control.
--- drivers/pci/hotplug/Kconfig | 13 ++ drivers/pci/hotplug/Makefile | 3 +- drivers/pci/hotplug/acpiphp_ampere_altra.c | 141 +++++++++++++++++++++ 3 files changed, 156 insertions(+), 1 deletion(-) create mode 100644 drivers/pci/hotplug/acpiphp_ampere_altra.c
drivers/pci/hotplug/Kconfig +13 -0
@@ -61,6 +61,19 @@ config HOTPLUG_PCI_ACPI When in doubt, say N. +config HOTPLUG_PCI_ACPI_AMPERE_ALTRA + tristate "ACPI PCI Hotplug driver Ampere Altra extensions" + depends on HOTPLUG_PCI_ACPI + depends on HAVE_ARM_SMCCC_DISCOVERY + depends on m + help + Say Y here if you have an Ampere Altra system. + + To compile this driver as a module, choose M here: the + module will be called acpiphp_ampere_altra. + + When in doubt, say N. + config HOTPLUG_PCI_ACPI_IBM tristate "ACPI PCI Hotplug driver IBM extensions" depends on HOTPLUG_PCI_ACPI
drivers/pci/hotplug/Makefile +2 -1
@@ -21,8 +21,9 @@ obj-$(CONFIG_HOTPLUG_PCI_RPA_DLPAR) += rpadlpar_io.o obj-$(CONFIG_HOTPLUG_PCI_ACPI) += acpiphp.o obj-$(CONFIG_HOTPLUG_PCI_S390) += s390_pci_hpc.o -# acpiphp_ibm extends acpiphp, so should be linked afterwards. +# acpiphp_ibm extend acpiphp, so should be linked afterwards. +obj-$(CONFIG_HOTPLUG_PCI_ACPI_AMPERE_ALTRA) += acpiphp_ampere_altra.o obj-$(CONFIG_HOTPLUG_PCI_ACPI_IBM) += acpiphp_ibm.o pci_hotplug-objs := pci_hotplug_core.o
drivers/pci/hotplug/acpiphp_ampere_altra.c new file +141 -0
141 lines not on this page · raw message
Signature · 1 line
2.41.0
Quoted 17 lines · D Scott Phillips
On Ampere Altra, PCIe hotplug is handled through ACPI. A side interface is also present to request system firmware control of attention LEDs. Add an ACPI PCI Hotplug companion driver to support attention LED control.
Signed-off-by D Scott Phillips <[email protected]>--- drivers/pci/hotplug/Kconfig | 13 ++ drivers/pci/hotplug/Makefile | 3 +- drivers/pci/hotplug/acpiphp_ampere_altra.c | 141 +++++++++++++++++++++ 3 files changed, 156 insertions(+), 1 deletion(-) create mode 100644 drivers/pci/hotplug/acpiphp_ampere_altra.cdrivers/pci/hotplug/Kconfig +0
-0
drivers/pci/hotplug/Kconfig config HOTPLUG_PCI_ACPI · line 68
Quoted 8 lines
drivers/pci/hotplug/Kconfig +5
-0@@ -61,6 +61,19 @@ config HOTPLUG_PCI_ACPI When in doubt, say N. +config HOTPLUG_PCI_ACPI_AMPERE_ALTRA + tristate "ACPI PCI Hotplug driver Ampere Altra extensions" + depends on HOTPLUG_PCI_ACPI + depends on HAVE_ARM_SMCCC_DISCOVERY + depends on m
Why is this restricted to being a module? It's not unprecedented, but unless this only works as a module for some reason, I would leave that choice up to the user.
Quoted 32 lines
drivers/pci/hotplug/Kconfig +8
-0+ help + Say Y here if you have an Ampere Altra system. + + To compile this driver as a module, choose M here: the + module will be called acpiphp_ampere_altra. + + When in doubt, say N. + config HOTPLUG_PCI_ACPI_IBM tristate "ACPI PCI Hotplug driver IBM extensions" depends on HOTPLUG_PCI_ACPIdrivers/pci/hotplug/Makefile +2
-1@@ -21,8 +21,9 @@ obj-$(CONFIG_HOTPLUG_PCI_RPA_DLPAR) += rpadlpar_io.o obj-$(CONFIG_HOTPLUG_PCI_ACPI) += acpiphp.o obj-$(CONFIG_HOTPLUG_PCI_S390) += s390_pci_hpc.o -# acpiphp_ibm extends acpiphp, so should be linked afterwards. +# acpiphp_ibm extend acpiphp, so should be linked afterwards. +obj-$(CONFIG_HOTPLUG_PCI_ACPI_AMPERE_ALTRA) += acpiphp_ampere_altra.o obj-$(CONFIG_HOTPLUG_PCI_ACPI_IBM) += acpiphp_ibm.o pci_hotplug-objs := pci_hotplug_core.odrivers/pci/hotplug/acpiphp_ampere_altra.c new file +0
-0
drivers/pci/hotplug/acpiphp_ampere_altra.c line 3
Quoted 3 lines
drivers/pci/hotplug/acpiphp_ampere_altra.c new file +3
-0@@ -0,0 +1,141 @@ +// SPDX-License-Identifier: GPL-2.0 +/* +* ACPI PCI Hot Plug Ampere Altra Extension
Would be helpful to include a hint about what this module *does*. IIUC, it controls the attention indicator.
drivers/pci/hotplug/acpiphp_ampere_altra.c line 6
Quoted 3 lines
drivers/pci/hotplug/acpiphp_ampere_altra.c new file +3
-0+* +* Copyright (C) 2023 Ampere Computing LLC +*
Spurious blank line.
Quoted 51 lines
drivers/pci/hotplug/acpiphp_ampere_altra.c new file +51
-0+*/ + +#define pr_fmt (fmt) "acpiphp_ampere_altra: " fmt + +#include <linux/init.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/pci_hotplug.h> + +#include "acpiphp.h" + +#define HANDLE_OPEN 0xb0200000 +#define HANDLE_CLOSE 0xb0300000 +#define REQUEST 0xf0700000 +#define LED_CMD 0x00000004 +#define LED_ATTENTION 0x00000002 +#define LED_SET_ON 0x00000001 +#define LED_SET_OFF 0x00000002 +#define LED_SET_BLINK 0x00000003 + +static const struct acpi_device_id acpi_ids[] = { + {"AMPC0008" ,0 }, {} +}; +MODULE_DEVICE_TABLE (acpi, acpi_ids); + +static u32 led_service_id[4 ]; + +static int led_status (u8 status) +{ +switch (status) { +case 1 :return LED_SET_ON ; +case 2 :return LED_SET_BLINK ; +default :return LED_SET_OFF ; + } +} + +static int set_attention_status (struct hotplug_slot *slot,u8 status) +{ +struct arm_smccc_res res; +struct pci_bus *bus; +struct pci_dev *root_port; +unsigned long flags; +u32 handle; +int ret =0 ; + + bus = slot->pci_slot->bus; + root_port =pcie_find_root_port (bus->self); +if (!root_port) +return -ENODEV ; + +local_irq_save (flags);
drivers/pci/hotplug/acpiphp_ampere_altra.c line 67
Quoted 10 lines
drivers/pci/hotplug/acpiphp_ampere_altra.c new file +10
-0+arm_smccc_smc (HANDLE_OPEN , led_service_id[0 ], led_service_id[1 ], + led_service_id[2 ], led_service_id[3 ],0 ,0 ,0 , &res); +if (res.a0) { + ret = -ENODEV ; + goto out; + } + handle = res.a1 &0xffff0000 ; + + arm_smccc_smc(REQUEST, LED_CMD, led_status(status), LED_ATTENTION, + pci_domain_nr(bus) | ((root_port->devfn >> 3) << 4), 0, 0,
PCI_SLOT(root_port->devfn)
Quoted 29 lines
drivers/pci/hotplug/acpiphp_ampere_altra.c new file +29
-0+ handle, &res); +if (res.a0) + ret = -ENODEV ; + +arm_smccc_smc (HANDLE_CLOSE , handle,0 ,0 ,0 ,0 ,0 ,0 , &res); + + out: +local_irq_restore (flags); +return ret; +} + +static int get_attention_status (struct hotplug_slot *slot,u8 *status) +{ +return -EINVAL ; +} + +static struct acpiphp_attention_info ampere_altra_attn = { + .set_attn = set_attention_status, + .get_attn = get_attention_status, + .owner =THIS_MODULE , +}; + +static acpi_status __init get_acpi_handle (acpi_handle handle,u32 level, +void *context,void **return_value) +{ + *(acpi_handle *)return_value = handle; +return AE_CTRL_TERMINATE ; +} +
drivers/pci/hotplug/acpiphp_ampere_altra.c line 106
Quoted 10 lines
drivers/pci/hotplug/acpiphp_ampere_altra.c new file +10
-0+static int __init acpiphp_ampere_altra_init (void ) +{ +struct fwnode_handle *fwnode; +acpi_handle leds_handle =NULL ; +struct acpi_device *leds; +acpi_status status; +int ret; + + status =acpi_get_devices ("AMPC0008" , get_acpi_handle,NULL , + &leds_handle);
Rafael, can you comment on whether we should use acpi_get_devices(), acpi_bus_register_driver(), acpi_acpi_scan_add_handler(), or something else here? I try to avoid pci_get_device() because it subverts the driver model (no hotplug support, no driver/device binding).
I see Documentation/driver-api/acpi/scan_handlers.rst, but I'm not clear on when to use acpi_bus_register_driver() vs acpi_acpi_scan_add_handler().
I guess the only ACPI connection here is to retrieve the "uuid" property once, and there's no need for any ACPI services after that.
Quoted 39 lines
drivers/pci/hotplug/acpiphp_ampere_altra.c new file +35
-0+if (ACPI_FAILURE (status) || !leds_handle) +return -ENODEV ; + leds =acpi_get_acpi_dev (leds_handle); +if (!leds) { +pr_err ("can't find device\n" ); +return -ENODEV ; + } + + fwnode =acpi_fwnode_handle (leds); + ret =fwnode_property_read_u32_array (fwnode,"uuid" , led_service_id,4 ); +acpi_put_acpi_dev (leds); +if (ret) { +pr_err ("can't find uuid\n" ); +return -ENODEV ; + } + +if (acpiphp_register_attention (&ere_altra_attn)) { +pr_err ("can't register driver\n" ); +return -ENODEV ; + } + +return 0 ; +} + +module_init (acpiphp_ampere_altra_init); + +static void __exit acpiphp_ampere_altra_exit(void) +{ +acpiphp_unregister_attention (&ere_altra_attn); +} + +module_exit (acpiphp_ampere_altra_exit); + +MODULE_AUTHOR ("D Scott Phillips <[email protected]>" ); +MODULE_LICENSE ("GPL" );Signature · 1 line
2.41.0
Quoted 21 lines · Bjorn Helgaas
Quoted 20 lines · D Scott Phillips
On Ampere Altra, PCIe hotplug is handled through ACPI. A side interface is also present to request system firmware control of attention LEDs. Add an ACPI PCI Hotplug companion driver to support attention LED control.
Signed-off-by D Scott Phillips <[email protected]>--- drivers/pci/hotplug/Kconfig | 13 ++ drivers/pci/hotplug/Makefile | 3 +- drivers/pci/hotplug/acpiphp_ampere_altra.c | 141 +++++++++++++++++++++ 3 files changed, 156 insertions(+), 1 deletion(-) create mode 100644 drivers/pci/hotplug/acpiphp_ampere_altra.cdrivers/pci/hotplug/Kconfig +0
-0@@ -61,6 +61,19 @@ config HOTPLUG_PCI_ACPI When in doubt, say N.
Quoted 9 lines
drivers/pci/hotplug/Kconfig config HOTPLUG_PCI_ACPI · line 68
Quoted 5 lines
drivers/pci/hotplug/Kconfig +5
-0+config HOTPLUG_PCI_ACPI_AMPERE_ALTRA + tristate "ACPI PCI Hotplug driver Ampere Altra extensions" + depends on HOTPLUG_PCI_ACPI + depends on HAVE_ARM_SMCCC_DISCOVERY + depends on mWhy is this restricted to being a module? It's not unprecedented, but unless this only works as a module for some reason, I would leave that choice up to the user.
I did that because acpiphp_register_attention() wouldn't register the handler unless it was built as a module. Maybe better would be this change first:
drivers/pci/hotplug/acpiphp_core.c +1 -2
@@ -78,8 +78,7 @@ int acpiphp_register_attention(struct acpiphp_attention_info *info) {int retval = -EINVAL ; -if (info && info->owner && info->set_attn && - info->get_attn && !attention_info) { +if (info && info->set_attn && info->get_attn && !attention_info) { retval =0 ; attention_info = info; }
Quoted 23 lines · D Scott Phillips
Quoted 5 lines · Bjorn Helgaas
Quoted 3 lines · D Scott Phillips
On Ampere Altra, PCIe hotplug is handled through ACPI. A side interface is also present to request system firmware control of attention LEDs. Add an ACPI PCI Hotplug companion driver to support attention LED control.
Quoted 9 lines
Review
Quoted 5 lines
(quoted diff) +5
-0+config HOTPLUG_PCI_ACPI_AMPERE_ALTRA + tristate "ACPI PCI Hotplug driver Ampere Altra extensions" + depends on HOTPLUG_PCI_ACPI + depends on HAVE_ARM_SMCCC_DISCOVERY + depends on mWhy is this restricted to being a module? It's not unprecedented, but unless this only works as a module for some reason, I would leave that choice up to the user.
I did that because
acpiphp_register_attention()wouldn't register the handler unless it was built as a module. Maybe better would be this change first:
drivers/pci/hotplug/acpiphp_core.c int acpiphp_register_attention(struct acpiphp_attention_info *info) · line 84
Quoted 9 lines
drivers/pci/hotplug/acpiphp_core.c +1
-2@@ -78,8 +78,7 @@ int acpiphp_register_attention(struct acpiphp_attention_info *info) {int retval = -EINVAL ; -if (info && info->owner && info->set_attn && - info->get_attn && !attention_info) { +if (info && info->set_attn && info->get_attn && !attention_info) { retval =0 ; attention_info = info; }
I would investigate the history of that "info->owner" check to see if it's required somewhere. If not, it seems like we could drop it.
At one time, we did support building hotplug drivers, including acpiphp, as modules, but we no longer do. Maybe that test dates from that time.
Bjorn
Rafael J. Wysocki
maintainerQuoted 176 lines · Bjorn Helgaas
Quoted 17 lines · D Scott Phillips
On Ampere Altra, PCIe hotplug is handled through ACPI. A side interface is also present to request system firmware control of attention LEDs. Add an ACPI PCI Hotplug companion driver to support attention LED control.
Signed-off-by D Scott Phillips <[email protected]>--- drivers/pci/hotplug/Kconfig | 13 ++ drivers/pci/hotplug/Makefile | 3 +- drivers/pci/hotplug/acpiphp_ampere_altra.c | 141 +++++++++++++++++++++ 3 files changed, 156 insertions(+), 1 deletion(-) create mode 100644 drivers/pci/hotplug/acpiphp_ampere_altra.cdrivers/pci/hotplug/Kconfig +0
-0drivers/pci/hotplug/Kconfig config HOTPLUG_PCI_ACPI · line 68
Quoted 8 lines
drivers/pci/hotplug/Kconfig +5
-0@@ -61,6 +61,19 @@ config HOTPLUG_PCI_ACPI When in doubt, say N. +config HOTPLUG_PCI_ACPI_AMPERE_ALTRA + tristate "ACPI PCI Hotplug driver Ampere Altra extensions" + depends on HOTPLUG_PCI_ACPI + depends on HAVE_ARM_SMCCC_DISCOVERY + depends on mWhy is this restricted to being a module? It's not unprecedented, but unless this only works as a module for some reason, I would leave that choice up to the user.
Quoted 32 lines
drivers/pci/hotplug/Kconfig +8
-0+ help + Say Y here if you have an Ampere Altra system. + + To compile this driver as a module, choose M here: the + module will be called acpiphp_ampere_altra. + + When in doubt, say N. + config HOTPLUG_PCI_ACPI_IBM tristate "ACPI PCI Hotplug driver IBM extensions" depends on HOTPLUG_PCI_ACPIdrivers/pci/hotplug/Makefile +2
-1@@ -21,8 +21,9 @@ obj-$(CONFIG_HOTPLUG_PCI_RPA_DLPAR) += rpadlpar_io.o obj-$(CONFIG_HOTPLUG_PCI_ACPI) += acpiphp.o obj-$(CONFIG_HOTPLUG_PCI_S390) += s390_pci_hpc.o -# acpiphp_ibm extends acpiphp, so should be linked afterwards. +# acpiphp_ibm extend acpiphp, so should be linked afterwards. +obj-$(CONFIG_HOTPLUG_PCI_ACPI_AMPERE_ALTRA) += acpiphp_ampere_altra.o obj-$(CONFIG_HOTPLUG_PCI_ACPI_IBM) += acpiphp_ibm.o pci_hotplug-objs := pci_hotplug_core.odrivers/pci/hotplug/acpiphp_ampere_altra.c new file +0
-0drivers/pci/hotplug/acpiphp_ampere_altra.c line 3
Quoted 3 lines
drivers/pci/hotplug/acpiphp_ampere_altra.c new file +3
-0@@ -0,0 +1,141 @@ +// SPDX-License-Identifier: GPL-2.0 +/* +* ACPI PCI Hot Plug Ampere Altra Extension Would be helpful to include a hint about what this module *does*. IIUC, it controls the attention indicator.
drivers/pci/hotplug/acpiphp_ampere_altra.c line 6
Quoted 3 lines
drivers/pci/hotplug/acpiphp_ampere_altra.c new file +3
-0+* +* Copyright (C) 2023 Ampere Computing LLC +* Spurious blank line.
Quoted 51 lines
drivers/pci/hotplug/acpiphp_ampere_altra.c new file +51
-0+*/ + +#define pr_fmt (fmt) "acpiphp_ampere_altra: " fmt + +#include <linux/init.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/pci_hotplug.h> + +#include "acpiphp.h" + +#define HANDLE_OPEN 0xb0200000 +#define HANDLE_CLOSE 0xb0300000 +#define REQUEST 0xf0700000 +#define LED_CMD 0x00000004 +#define LED_ATTENTION 0x00000002 +#define LED_SET_ON 0x00000001 +#define LED_SET_OFF 0x00000002 +#define LED_SET_BLINK 0x00000003 + +static const struct acpi_device_id acpi_ids[] = { + {"AMPC0008" ,0 }, {} +}; +MODULE_DEVICE_TABLE (acpi, acpi_ids); + +static u32 led_service_id[4 ]; + +static int led_status (u8 status) +{ +switch (status) { +case 1 :return LED_SET_ON ; +case 2 :return LED_SET_BLINK ; +default :return LED_SET_OFF ; + } +} + +static int set_attention_status (struct hotplug_slot *slot,u8 status) +{ +struct arm_smccc_res res; +struct pci_bus *bus; +struct pci_dev *root_port; +unsigned long flags; +u32 handle; +int ret =0 ; + + bus = slot->pci_slot->bus; + root_port =pcie_find_root_port (bus->self); +if (!root_port) +return -ENODEV ; + +local_irq_save (flags);drivers/pci/hotplug/acpiphp_ampere_altra.c line 67
Quoted 10 lines
drivers/pci/hotplug/acpiphp_ampere_altra.c new file +10
-0+arm_smccc_smc (HANDLE_OPEN , led_service_id[0 ], led_service_id[1 ], + led_service_id[2 ], led_service_id[3 ],0 ,0 ,0 , &res); +if (res.a0) { + ret = -ENODEV ; + goto out; + } + handle = res.a1 &0xffff0000 ; + + arm_smccc_smc(REQUEST, LED_CMD, led_status(status), LED_ATTENTION, + pci_domain_nr(bus) | ((root_port->devfn >> 3) << 4), 0, 0,
PCI_SLOT(root_port->devfn)Quoted 35 lines
drivers/pci/hotplug/acpiphp_ampere_altra.c new file +35
-0+ handle, &res); +if (res.a0) + ret = -ENODEV ; + +arm_smccc_smc (HANDLE_CLOSE , handle,0 ,0 ,0 ,0 ,0 ,0 , &res); + + out: +local_irq_restore (flags); +return ret; +} + +static int get_attention_status (struct hotplug_slot *slot,u8 *status) +{ +return -EINVAL ; +} + +static struct acpiphp_attention_info ampere_altra_attn = { + .set_attn = set_attention_status, + .get_attn = get_attention_status, + .owner =THIS_MODULE , +}; + +static acpi_status __init get_acpi_handle (acpi_handle handle,u32 level, +void *context,void **return_value) +{ + *(acpi_handle *)return_value = handle; +return AE_CTRL_TERMINATE ; +} + +static int __init acpiphp_ampere_altra_init (void ) +{ +struct fwnode_handle *fwnode; +acpi_handle leds_handle =NULL ; +struct acpi_device *leds; +acpi_status status;
Quoted 8 lines
drivers/pci/hotplug/acpiphp_ampere_altra.c line 106
Quoted 4 lines
drivers/pci/hotplug/acpiphp_ampere_altra.c new file +4
-0+int ret; + + status =acpi_get_devices ("AMPC0008" , get_acpi_handle,NULL , + &leds_handle);Rafael, can you comment on whether we should use
acpi_get_devices(),acpi_bus_register_driver(),acpi_acpi_scan_add_handler(), or something else here?
Personally, I would go for a platform driver, because the ACPI core should create a platform device for this object.
acpi_get_devices() carries out a namespace walk that is costly and entirely avoidable.
Quoted 5 lines
I try to avoid
pci_get_device()because it subverts the
driver model (no hotplug support, no driver/device binding).I see
Documentation/driver-api/acpi/scan_handlers.rst, but I'm not clear on when to useacpi_bus_register_driver()vs
Never.
Quoted 1 line
acpi_acpi_scan_add_handler().
When you don't want the ACPI core to create a platform device for your ACPI device object. There are cases like that, but they are rare.
Quoted 2 lines
I guess the only ACPI connection here is to retrieve the "uuid" property once, and there's no need for any ACPI services after that.
That's in agreement with my understanding.
Quoted 33 lines · Rafael J. Wysocki
Quoted 5 lines · Bjorn Helgaas
Quoted 3 lines · D Scott Phillips
On Ampere Altra, PCIe hotplug is handled through ACPI. A side interface is also present to request system firmware control of attention LEDs. Add an ACPI PCI Hotplug companion driver to support attention LED control.
Quoted 14 lines
drivers/pci/hotplug/acpiphp_ampere_altra.c line 106
Quoted 10 lines
drivers/pci/hotplug/acpiphp_ampere_altra.c new file +10
-0+static int __init acpiphp_ampere_altra_init (void ) +{ +struct fwnode_handle *fwnode; +acpi_handle leds_handle =NULL ; +struct acpi_device *leds; +acpi_status status; +int ret; + + status =acpi_get_devices ("AMPC0008" , get_acpi_handle,NULL , + &leds_handle);Rafael, can you comment on whether we should use
acpi_get_devices(),acpi_bus_register_driver(),acpi_acpi_scan_add_handler(), or something else here?Personally, I would go for a platform driver, because the ACPI core should create a platform device for this object.
acpi_get_devices()carries out a namespace walk that is costly and entirely avoidable.Quoted 5 lines
I try to avoid
pci_get_device()because it subverts the
driver model (no hotplug support, no driver/device binding).I see
Documentation/driver-api/acpi/scan_handlers.rst, but I'm not clear on when to useacpi_bus_register_driver()vs
Quoted 6 lines
Never.
Quoted 1 line
acpi_acpi_scan_add_handler().When you don't want the ACPI core to create a platform device for your ACPI device object. There are cases like that, but they are rare.
Ah, so none of the above (not acpi_get_devices(), acpi_bus_register_driver(), OR acpi_acpi_scan_add_handler()).
IIUC, what you propose would look something like this:
static u32 led_service_id[4];
static int altra_led_probe(struct platform_device *pdev)
{
struct fwnode_handle *fwnode = dev_fwnode(&pdev->dev);fwnode_property_read_u32_array(fwnode, "uuid", led_service_id, 4);
}
static const struct acpi_device_id altra_led_ids[] = {
{"AMPC0008", 0}, {}
};
MODULE_DEVICE_TABLE(acpi, altra_led_ids);
static struct platform_driver altra_led_driver = {
.driver = {
.acpi_match_table = altra_led_ids,
},
.probe = altra_led_probe,
};
module_platform_driver(altra_led_driver);Bjorn
Quoted 55 lines · Bjorn Helgaas
Quoted 33 lines · Rafael J. Wysocki
Quoted 5 lines · Bjorn Helgaas
Quoted 3 lines · D Scott Phillips
On Ampere Altra, PCIe hotplug is handled through ACPI. A side interface is also present to request system firmware control of attention LEDs. Add an ACPI PCI Hotplug companion driver to support attention LED control.
Quoted 14 lines
drivers/pci/hotplug/acpiphp_ampere_altra.c line 106
Quoted 10 lines
drivers/pci/hotplug/acpiphp_ampere_altra.c new file +10
-0+static int __init acpiphp_ampere_altra_init (void ) +{ +struct fwnode_handle *fwnode; +acpi_handle leds_handle =NULL ; +struct acpi_device *leds; +acpi_status status; +int ret; + + status =acpi_get_devices ("AMPC0008" , get_acpi_handle,NULL , + &leds_handle);Rafael, can you comment on whether we should use
acpi_get_devices(),acpi_bus_register_driver(),acpi_acpi_scan_add_handler(), or something else here?Personally, I would go for a platform driver, because the ACPI core should create a platform device for this object.
acpi_get_devices()carries out a namespace walk that is costly and entirely avoidable.Quoted 5 lines
I try to avoid
pci_get_device()because it subverts the
driver model (no hotplug support, no driver/device binding).I see
Documentation/driver-api/acpi/scan_handlers.rst, but I'm not clear on when to useacpi_bus_register_driver()vsQuoted 6 lines
Never.
Quoted 1 line
acpi_acpi_scan_add_handler().When you don't want the ACPI core to create a platform device for your ACPI device object. There are cases like that, but they are rare.
Ah, so none of the above (not
acpi_get_devices(),acpi_bus_register_driver(), ORacpi_acpi_scan_add_handler()).IIUC, what you propose would look something like this:
static u32 led_service_id[4]; static int altra_led_probe(struct platform_device *pdev) { struct fwnode_handle *fwnode = dev_fwnode(&pdev->dev);fwnode_property_read_u32_array(fwnode, "uuid", led_service_id, 4);}
Quoted 12 lines
static const struct acpi_device_id altra_led_ids[] = {
{"AMPC0008", 0}, {}
};
MODULE_DEVICE_TABLE(acpi, altra_led_ids);
static struct platform_driver altra_led_driver = {
.driver = {
.acpi_match_table = altra_led_ids,
},
.probe = altra_led_probe,
};
module_platform_driver(altra_led_driver);Ok, thanks Bjorn & Rafael, will do.