HID: mcp2200: added driver for GPIOs of MCP2200
PATCH v7 1/1 HID: mcp2200: added driver for GPIOs of MCP2200
Added a gpiochip compatible driver to control the 8 GPIOs of the MCP2200 by using the HID interface.
Using GPIOs with alternative functions (GP0<->SSPND, GP1<->USBCFG, GP6<->RXLED, GP7<->TXLED) will reset the functions, if set (unset by default).
The driver was tested while also using the UART of the chip. Setting and reading the GPIOs has no effect on the UART communication. However, a reset is triggered after the CONFIGURE command. If the GPIO Direction is constantly changed, this will affect the communication at low baud rates. This is a hardware problem of the MCP2200 and is not caused by the driver.
--- drivers/hid/Kconfig | 9 + drivers/hid/Makefile | 1 + drivers/hid/hid-ids.h | 1 + drivers/hid/hid-mcp2200.c | 392 ++++++++++++++++++++++++++++++++++++++ 4 files changed, 403 insertions(+) create mode 100644 drivers/hid/hid-mcp2200.c
drivers/hid/Kconfig +9 -0
@@ -1298,6 +1298,15 @@ config HID_ALPS Say Y here if you have a Alps touchpads over i2c-hid or usbhid and want support for its special functionalities. +config HID_MCP2200 + tristate "Microchip MCP2200 HID USB-to-GPIO bridge" + depends on USB_HID && GPIOLIB + help + Provides GPIO functionality over USB-HID through MCP2200 device. + + To compile this driver as a module, choose M here: the module + will be called hid-mcp2200.ko. + config HID_MCP2221 tristate "Microchip MCP2221 HID USB-to-I2C/SMbus host support" depends on USB_HID && I2C
drivers/hid/Makefile +1 -0
@@ -79,6 +79,7 @@ obj-$(CONFIG_HID_LOGITECH_HIDPP) += hid-logitech-hidpp.o obj-$(CONFIG_HID_MACALLY) += hid-macally.o obj-$(CONFIG_HID_MAGICMOUSE) += hid-magicmouse.o obj-$(CONFIG_HID_MALTRON) += hid-maltron.o +obj-$(CONFIG_HID_MCP2200) += hid-mcp2200.o obj-$(CONFIG_HID_MCP2221) += hid-mcp2221.o obj-$(CONFIG_HID_MAYFLASH) += hid-mf.o obj-$(CONFIG_HID_MEGAWORLD_FF) += hid-megaworld.o
drivers/hid/hid-ids.h +1 -0
@@ -915,6 +915,7 @@#define USB_DEVICE_ID_PICK16F1454 0x0042#define USB_DEVICE_ID_PICK16F1454_V2 0xf2f7#define USB_DEVICE_ID_LUXAFOR 0xf372 +#define USB_DEVICE_ID_MCP2200 0x00df#define USB_DEVICE_ID_MCP2221 0x00dd#define USB_VENDOR_ID_MICROSOFT 0x045e
drivers/hid/hid-mcp2200.c new file +392 -0
392 lines not on this page · raw message
Signature · 1 line
2.42.0
Quoted 14 lines · On Thu, 21 Sep, 2023 18:49:28 +0200 "Johannes Roith"…
Added a gpiochip compatible driver to control the 8 GPIOs of the MCP2200 by using the HID interface.
Using GPIOs with alternative functions (GP0<->SSPND, GP1<->USBCFG, GP6<->RXLED, GP7<->TXLED) will reset the functions, if set (unset by default).
The driver was tested while also using the UART of the chip. Setting and reading the GPIOs has no effect on the UART communication. However, a reset is triggered after the CONFIGURE command. If the GPIO Direction is constantly changed, this will affect the communication at low baud rates. This is a hardware problem of the MCP2200 and is not caused by the driver.
Quoted 2 lines
Signed-off-by Johannes Roith <[email protected]>---
Dear Maintainers,
my patch has undergone review by Rahul Rameshbabu, and I have addressed the feedback accordingly.
I understand that you all have busy schedules, and I appreciate the time and effort you dedicate to maintaining the Linux kernel. However, I would be grateful if you could provide an update on the patch's status and whether there are any further actions required from my end.
Best regards,
Johannes Roith
Jiri Kosina
maintainerQuoted 7 lines · Johannes Roith
Added a gpiochip compatible driver to control the 8 GPIOs of the MCP2200 by using the HID interface.
Using GPIOs with alternative functions (GP0<->SSPND, GP1<->USBCFG, GP6<->RXLED, GP7<->TXLED) will reset the functions, if set (unset by default).
Quoted 8 lines
The driver was tested while also using the UART of the chip. Setting and reading the GPIOs has no effect on the UART communication. However, a reset is triggered after the CONFIGURE command. If the GPIO Direction is constantly changed, this will affect the communication at low baud rates. This is a hardware problem of the MCP2200 and is not caused by the driver.
Signed-off-by Johannes Roith <[email protected]>
Now applied to hid.git#for-6.8/mcp2200. Thanks and sorry for the delay in the review.
Signature · 2 lines
Jiri Kosina SUSE Labs