scsi: Allow scsi_execute users to request retries
Subsystems (2)
v12 cover scsi: Allow scsi_execute users to request retries
The following patches were made over Martin's 6.7 staging branch which contains a sd change that this patch requires.
The patches allow scsi_execute_cmd users to have scsi-ml retry the cmd for it instead of the caller having to parse the error and loop itself.
Note that I dropped most reviewed-by tags, because the structs changed where before we only had struct scsi_failure we now have the struct scsi_failure that is in:
struct scsi_failures {
/*
* If the failure does not have a specific limit in the scsi_failure
* then this limit is followed.
*/
int total_allowed;
int total_retries;
struct scsi_failure *failure_definitions;
};so we can limit the total number of retries. The setup for this is then different and I'm not sure if we everyone will like it. The other parts of the conversions patches have not changed.
drivers/scsi/Kconfig | 9 + drivers/scsi/ch.c | 27 ++- drivers/scsi/device_handler/scsi_dh_hp_sw.c | 49 +++-- drivers/scsi/device_handler/scsi_dh_rdac.c | 84 +++---- drivers/scsi/scsi_lib.c | 26 ++- drivers/scsi/scsi_lib_test.c | 330 ++++++++++++++++++++++++++++ drivers/scsi/scsi_scan.c | 107 +++++---- drivers/scsi/scsi_transport_spi.c | 35 +-- drivers/scsi/sd.c | 326 +++++++++++++++++---------- drivers/scsi/ses.c | 66 ++++-- drivers/scsi/sr.c | 38 ++-- drivers/ufs/core/ufshcd.c | 22 +- 12 files changed, 822 insertions(+), 297 deletions(-)
v12:
- Fix bug where a user could request no retries and skip going through the scsi-eh.
- Drop support for allowing caller to have scsi-ml not retry failures (we only allow caller to request retries).
- Fix formatting.
- Add support to control total number of retries.
- Fix kunit tests to add a missing test and comments.
- Fix missing SCMD_FAILURE_ASCQ_ANY in sd_spinup_disk.
v11:
- Document scsi_failure.result special values
- Fix sshdr fix git commit message where there was a missing word
- Use designated initializers for cdb setup
- Fix up various coding style comments from John like redoing if/else error/success checks.
- Add patch to fix rdac issue where stale SCSH_DH values were returned
- Remove old comment from:
"[PATCH v10 16/33] scsi: spi: Have scsi-ml retry spi_execute errors"
- Drop EOPNOTSUPP use from:
"[PATCH v10 17/33] scsi: sd: Fix sshdr use in sd_suspend_common"
- Init errno to 0 when declared in:
"[PATCH v10 20/33] scsi: ch: Have scsi-ml retry ch_do_scsi errors"
- Add diffstat below
v10:
- Drop "," after {}.
- Hopefully fix outlook issues.
v9:
- Drop spi_execute changes from [PATCH] scsi: spi: Fix sshdr use
- Change git commit message for sshdr use fixes.
v8:
- Rebase.
- Saw the discussion about the possible bug where callers are accessing the sshdr when it's not setup, so I added some patches for that since I was going over the same code.
v7:
- Rebase against scsi_execute_cmd patchset.
v6:
- Fix kunit build when it's built as a module but scsi is not.
- Drop [PATCH 17/35] scsi: ufshcd: Convert to scsi_exec_req because that driver no longer uses scsi_execute.
- Convert ufshcd to use the scsi_failures struct because it now just does direct retries and does not do it's own deadline timing.
- Add back memset in read_capacity_16.
- Remove memset in get_sectorsize and replace with { } to init buf.
v5:
- Fix spelling (made sure I ran checkpatch strict)
- Drop SCMD_FAILURE_NONE
- Rename SCMD_FAILURE_ANY
- Fix media_not_present handling where it was being retried instead of failed.
- Fix ILLEGAL_REQUEST handling in read_capacity_16 so it was not retried.
- Fix coding style, spelling and and naming convention in kunit and added more tests to handle cases like the media_not_present one where we want to force failures instead of retries.
- Drop cxlflash patch because it actually checked it's internal state before performing a retry which we currently do not support.
v4:
- Redefine cmd definitions if the cmd is touched.
- Fix up coding style issues.
- Use sam_status enum.
- Move failures initialization to scsi_initialize_rq (also fixes KASAN error).
- Add kunit test.
- Add function comments.
v3:
- Use a for loop in scsi_check_passthrough
- Fix result handling/testing.
- Fix scsi_status_is_good handling.
- make __scsi_exec_req take a const arg
- Fix formatting in patch 24
v2:
- Rename scsi_prep_sense
- Change scsi_check_passthrough's loop and added some fixes
- Modified scsi_execute* so it uses a struct to pass in args
PATCH v12 1/20 scsi: Allow passthrough to request scsi-ml retries
For passthrough we don't retry any error we get a check condition for. This results in a lot of callers driving their own retries for all UAs, specific UAs, NOT_READY, specific sense values or any type of failure.
This adds the core code to allow passthrough users to specify what errors they want scsi-ml to retry for them. We can then convert users to drop a lot of their sense parsing and retry handling.
--- drivers/scsi/scsi_lib.c | 92 ++++++++++++++++++++++++++++++++++++++ include/scsi/scsi_device.h | 48 ++++++++++++++++++++ 2 files changed, 140 insertions(+)
drivers/scsi/scsi_lib.c +92 -0
@@ -184,6 +184,92 @@ void scsi_queue_insert(struct scsi_cmnd *cmd, int reason)__scsi_queue_insert (cmd, reason, true); } +void scsi_reset_failures (struct scsi_failures *failures) +{ +struct scsi_failure *failure; + + failures->total_retries =0 ; + +for (failure = failures->failure_definitions; failure->result; + failure++) + failure->retries =0 ; +} +EXPORT_SYMBOL_GPL (scsi_reset_failures); + +/** +* scsi_check_passthrough - Determine if passthrough scsi_cmnd needs a retry. +* @scmd: scsi_cmnd to check. +* @failures: scsi_failures struct that lists failures to check for. +* +* Returns -EAGAIN if the caller should retry else 0. +*/ +static int scsi_check_passthrough (struct scsi_cmnd *scmd, +struct scsi_failures *failures) +{ +struct scsi_failure *failure; +struct scsi_sense_hdr sshdr; +enum sam_status status; + +if (!failures) +return 0 ; + +for (failure = failures->failure_definitions; failure->result; + failure++) { +if (failure->result ==SCMD_FAILURE_RESULT_ANY ) + goto maybe_retry; + +if (host_byte (scmd->result) && +host_byte (scmd->result) ==host_byte (failure->result)) + goto maybe_retry; + + status =status_byte (scmd->result); +if (!status) +continue ; + +if (failure->result ==SCMD_FAILURE_STAT_ANY && + !scsi_status_is_good (scmd->result)) + goto maybe_retry; + +if (status !=status_byte (failure->result)) +continue ; + +if (status_byte (failure->result) !=SAM_STAT_CHECK_CONDITION || + failure->sense ==SCMD_FAILURE_SENSE_ANY ) + goto maybe_retry; + +if (!scsi_command_normalize_sense (scmd, &sshdr)) +return 0 ; + +if (failure->sense != sshdr.sense_key) +continue ; + +if (failure->asc ==SCMD_FAILURE_ASC_ANY ) + goto maybe_retry; + +if (failure->asc != sshdr.asc) +continue ; + +if (failure->ascq ==SCMD_FAILURE_ASCQ_ANY || + failure->ascq == sshdr.ascq) + goto maybe_retry; + } + +return 0 ; + +maybe_retry: +if (failure->allowed) { +if (failure->allowed ==SCMD_FAILURE_NO_LIMIT || + ++failure->retries <= failure->allowed) +return -EAGAIN ; + }else { +if (failures->total_allowed ==SCMD_FAILURE_NO_LIMIT || + ++failures->total_retries <= failures->total_allowed) +return -EAGAIN ; + } + +return 0 ; +} +/** * scsi_execute_cmd - insert request and wait for the result * @sdev: scsi_device
@@ -214,6 +300,7 @@ int scsi_execute_cmd(struct scsi_device *sdev, const unsigned char *cmd, args->sense_len != SCSI_SENSE_BUFFERSIZE))return -EINVAL ; +retry: req =scsi_alloc_request (sdev->request_queue, opf, args->req_flags);if (IS_ERR (req))return PTR_ERR (req);
@@ -237,6 +324,11 @@ int scsi_execute_cmd(struct scsi_device *sdev, const unsigned char *cmd,*/ blk_execute_rq (req, true); +if (scsi_check_passthrough (scmd, args->failures) == -EAGAIN ) { +blk_mq_free_request (req); + goto retry; + } +/* * Some devices (USB mass-storage in particular) may transfer * garbage data together with a residue indicating that the data
include/scsi/scsi_device.h +48 -0
66 lines not on this page · raw message
Signature · 1 line
2.34.1
Re: [PATCH v12 01/20] scsi: Allow passthrough to request scsi-ml retries
Quoted 1 line · Mike Christie
For passthrough we don't retry any error we get a check condition for.
nit: For passthrough we don't retry any error which we get a check condition for.
Quoted 8 lines
This results in a lot of callers driving their own retries for all UAs, specific UAs,
NOT_READY, specific sense values or any type of failure.This adds the core code to allow passthrough users to specify what errors they want scsi-ml to retry for them. We can then convert users to drop a lot of their sense parsing and retry handling.
Signed-off-by Mike Christie <[email protected]>
Looks ok to me, so feel free to pick up:
Quoted 10 lines
--- drivers/scsi/scsi_lib.c | 92 ++++++++++++++++++++++++++++++++++++++ include/scsi/scsi_device.h | 48 ++++++++++++++++++++ 2 files changed, 140 insertions(+)drivers/scsi/scsi_lib.c +0
-0
drivers/scsi/scsi_lib.c void scsi_queue_insert(struct scsi_cmnd *cmd, int reason) · line 187
Quoted 4 lines
drivers/scsi/scsi_lib.c +1
-0@@ -184,6 +184,92 @@ void scsi_queue_insert(struct scsi_cmnd *cmd, int reason)__scsi_queue_insert (cmd, reason, true); } +void scsi_reset_failures (struct scsi_failures *failures)
nit: maybe scsi_reset_failures_retries as the name, to be more specific
Quoted 180 lines
drivers/scsi/scsi_lib.c +91
-0+{ +struct scsi_failure *failure; + + failures->total_retries =0 ; + +for (failure = failures->failure_definitions; failure->result; + failure++) + failure->retries =0 ; +} +EXPORT_SYMBOL_GPL (scsi_reset_failures); + +/** +* scsi_check_passthrough - Determine if passthrough scsi_cmnd needs a retry. +* @scmd: scsi_cmnd to check. +* @failures: scsi_failures struct that lists failures to check for. +* +* Returns -EAGAIN if the caller should retry else 0. +*/ +static int scsi_check_passthrough (struct scsi_cmnd *scmd, +struct scsi_failures *failures) +{ +struct scsi_failure *failure; +struct scsi_sense_hdr sshdr; +enum sam_status status; + +if (!failures) +return 0 ; + +for (failure = failures->failure_definitions; failure->result; + failure++) { +if (failure->result ==SCMD_FAILURE_RESULT_ANY ) + goto maybe_retry; + +if (host_byte (scmd->result) && +host_byte (scmd->result) ==host_byte (failure->result)) + goto maybe_retry; + + status =status_byte (scmd->result); +if (!status) +continue ; + +if (failure->result ==SCMD_FAILURE_STAT_ANY && + !scsi_status_is_good (scmd->result)) + goto maybe_retry; + +if (status !=status_byte (failure->result)) +continue ; + +if (status_byte (failure->result) !=SAM_STAT_CHECK_CONDITION || + failure->sense ==SCMD_FAILURE_SENSE_ANY ) + goto maybe_retry; + +if (!scsi_command_normalize_sense (scmd, &sshdr)) +return 0 ; + +if (failure->sense != sshdr.sense_key) +continue ; + +if (failure->asc ==SCMD_FAILURE_ASC_ANY ) + goto maybe_retry; + +if (failure->asc != sshdr.asc) +continue ; + +if (failure->ascq ==SCMD_FAILURE_ASCQ_ANY || + failure->ascq == sshdr.ascq) + goto maybe_retry; + } + +return 0 ; + +maybe_retry: +if (failure->allowed) { +if (failure->allowed ==SCMD_FAILURE_NO_LIMIT || + ++failure->retries <= failure->allowed) +return -EAGAIN ; + }else { +if (failures->total_allowed ==SCMD_FAILURE_NO_LIMIT || + ++failures->total_retries <= failures->total_allowed) +return -EAGAIN ; + } + +return 0 ; +} +/** * scsi_execute_cmd - insert request and wait for the result * @sdev: scsi_device @@ -214,6 +300,7 @@ int scsi_execute_cmd(struct scsi_device *sdev, const unsigned char *cmd, args->sense_len != SCSI_SENSE_BUFFERSIZE))return -EINVAL ; +retry: req =scsi_alloc_request (sdev->request_queue, opf, args->req_flags);if (IS_ERR (req))return PTR_ERR (req);@@ -237,6 +324,11 @@ int scsi_execute_cmd(struct scsi_device *sdev, const unsigned char *cmd,*/ blk_execute_rq (req, true); +if (scsi_check_passthrough (scmd, args->failures) == -EAGAIN ) { +blk_mq_free_request (req); + goto retry; + } +/* * Some devices (USB mass-storage in particular) may transfer * garbage data together with a residue indicating that the data include/scsi/scsi_device.h +48
-0@@ -483,6 +483,52 @@ extern int scsi_is_sdev_device(const struct device *);extern int scsi_is_target_device (const struct device *);extern void scsi_sanitize_inquiry_string (unsigned char *s,int len); +/* +* scsi_execute_cmd users can set scsi_failure.result to have +* scsi_check_passthrough fail/retry a command. scsi_failure.result can be a +* specific host byte or message code, or SCMD_FAILURE_RESULT_ANY can be used +* to match any host or message code. +*/ +#define SCMD_FAILURE_RESULT_ANY 0x7fffffff +/* +* Set scsi_failure.result to SCMD_FAILURE_STAT_ANY to fail/retry any failure +* scsi_status_is_good returns false for. +*/ +#define SCMD_FAILURE_STAT_ANY 0xff +/* +* The following can be set to the scsi_failure sense, asc and ascq fields to +* match on any sense, ASC, or ASCQ value. +*/ +#define SCMD_FAILURE_SENSE_ANY 0xff +#define SCMD_FAILURE_ASC_ANY 0xff +#define SCMD_FAILURE_ASCQ_ANY 0xff +/* Always retry a matching failure. */ +#define SCMD_FAILURE_NO_LIMIT -1 + +struct scsi_failure { +int result; +u8 sense; +u8 asc; +u8 ascq; + +/* +* Number of attempts allowed for this failure. It does not count +* for the total_allowed. +*/ +s8 allowed; +s8 retries; +}; + +struct scsi_failures { +/* +* If the failure does not have a specific limit in the scsi_failure +* then this limit is followed. +*/ +int total_allowed; +int total_retries; +struct scsi_failure *failure_definitions; +}; +/* Optional arguments to scsi_execute_cmd */ struct scsi_exec_args {unsigned char *sense;/* sense buffer */ @@ -491,12 +537,14 @@ struct scsi_exec_args {blk_mq_req_flags_t req_flags;/* BLK_MQ_REQ flags */ int scmd_flags;/* SCMD flags */ int *resid;/* residual length */ +struct scsi_failures *failures;/* failures to retry */ };int scsi_execute_cmd (struct scsi_device *sdev,const unsigned char *cmd,blk_opf_t opf,void *buffer,unsigned int bufflen,int timeout,int retries,const struct scsi_exec_args *args); +void scsi_reset_failures (struct scsi_failures *failures);extern void sdev_disable_disk_events (struct scsi_device *sdev);extern void sdev_enable_disk_events (struct scsi_device *sdev);
PATCH v12 2/20 scsi: Have scsi-ml retry scsi_probe_lun errors
In reply to Mike ChristieThis has scsi_probe_lun ask scsi-ml to retry UAs instead of driving them itself.
--- drivers/scsi/scsi_scan.c | 46 ++++++++++++++++++++++++---------------- 1 file changed, 28 insertions(+), 18 deletions(-)
drivers/scsi/scsi_scan.c +28 -18
@@ -626,6 +626,7 @@ void scsi_sanitize_inquiry_string(unsigned char *s, int len) }EXPORT_SYMBOL (scsi_sanitize_inquiry_string); +/** * scsi_probe_lun - probe a single LUN using a SCSI INQUIRY * @sdev: scsi_device to probe
@@ -647,10 +648,32 @@ static int scsi_probe_lun(struct scsi_device *sdev, unsigned char *inq_result,int first_inquiry_len, try_inquiry_len, next_inquiry_len;int response_len =0 ;int pass, count, result, resid; -struct scsi_sense_hdr sshdr; +struct scsi_failure failure_defs[] = { +/* +* not-ready to ready transition [asc/ascq=0x28/0x0] or +* power-on, reset [asc/ascq=0x29/0x0], continue. INQUIRY +* should not yield UNIT_ATTENTION but many buggy devices do +* so anyway. +*/ + { + .sense =UNIT_ATTENTION , + .asc =0x28 , + .result =SAM_STAT_CHECK_CONDITION , + }, + { + .sense =UNIT_ATTENTION , + .asc =0x29 , + .result =SAM_STAT_CHECK_CONDITION , + }, + {} + }; +struct scsi_failures failures = { + .total_allowed =3 , + .failure_definitions = failure_defs, + };const struct scsi_exec_args exec_args = { - .sshdr = &sshdr, .resid = &resid, + .failures = &failures, }; *bflags =0 ;
@@ -668,6 +691,8 @@ static int scsi_probe_lun(struct scsi_device *sdev, unsigned char *inq_result, pass, try_inquiry_len));/* Each pass gets up to three chances to ignore Unit Attention */ +scsi_reset_failures (&failures); +for (count =0 ; count <3 ; ++count) {memset (scsi_cmd,0 ,6 ); scsi_cmd[0 ] =INQUIRY ;
@@ -684,22 +709,7 @@ static int scsi_probe_lun(struct scsi_device *sdev, unsigned char *inq_result,"scsi scan: INQUIRY %s with code 0x%x\n" , result ? "failed" : "successful", result)); -if (result >0 ) { -/* -* not-ready to ready transition [asc/ascq=0x28/0x0] -* or power-on, reset [asc/ascq=0x29/0x0], continue. -* INQUIRY should not yield UNIT_ATTENTION -* but many buggy devices do so anyway. -*/ -if (scsi_status_is_check_condition (result) && -scsi_sense_valid (&sshdr)) { -if ((sshdr.sense_key ==UNIT_ATTENTION ) && - ((sshdr.asc ==0x28 ) || - (sshdr.asc ==0x29 )) && - (sshdr.ascq ==0 )) -continue ; - } - }else if (result ==0 ) { +if (result ==0 ) {/* * if nothing was transferred, we try * again. It's a workaround for some USB
Signature · 1 line
2.34.1
Re: [PATCH v12 02/20] scsi: Have scsi-ml retry scsi_probe_lun errors
drivers/scsi/scsi_scan.c static int scsi_probe_lun(struct scsi_device *sdev, unsigned char *inq_result, · line 696
Quoted 5 lines · Mike Christie
/* Each pass gets up to three chances to ignore Unit Attention */
drivers/scsi/scsi_scan.c +2
-0+scsi_reset_failures (&failures); +for (count =0 ; count <3 ; ++count) {
So do we keep this loop for the USB workaround (not shown)? I just wonder why we retry in this outer loop as well as now inside scsi_execute_cmd(). Maybe I'm missing something ....
Thanks,
John
Quoted 2 lines
memset(scsi_cmd, 0, 6); scsi_cmd[0] = INQUIRY;
Re: [PATCH v12 02/20] scsi: Have scsi-ml retry scsi_probe_lun errors
Quoted 7 lines · John Garry
Quoted 4 lines · Mike Christie
/* Each pass gets up to three chances to ignore Unit Attention */ +
scsi_reset_failures(&failures);
+
for (count = 0; count < 3; ++count) {So do we keep this loop for the USB workaround (not shown)? I just wonder why we retry in this outer loop as well as now inside
scsi_execute_cmd(). Maybe I'm missing something ....
The outer loop is for the inquiry len retries not shown. I didn't know it was for usb. It's where we retry with a different inquiry len to try and get more of the data. scsi_execute_cmd doesn't support that type of thing where the data len change between retries so we still have this loop.
PATCH v12 3/20 scsi: retry INQUIRY after timeout
In reply to Mike ChristieDescription from: Martin Wilck <[email protected]>:
The SCSI mid layer doesn't retry commands after DID_TIME_OUT (see scsi_noretry_cmd()). Packet loss in the fabric can cause spurious timeouts during SCSI device probing, causing device probing to fail. This has been observed in FCoE uplink failover tests, for example.
This patch fixes the issue by retrying the INQUIRY.
--- drivers/scsi/scsi_scan.c | 4 ++++ 1 file changed, 4 insertions(+)
drivers/scsi/scsi_scan.c +4 -0
@@ -665,6 +665,10 @@ static int scsi_probe_lun(struct scsi_device *sdev, unsigned char *inq_result, .asc = 0x29, .result = SAM_STAT_CHECK_CONDITION, }, + { + .allowed = 1, + .result = DID_TIME_OUT << 16, + }, {} };struct scsi_failures failures = {
Signature · 1 line
2.34.1
PATCH v12 4/20 scsi: sd: Have scsi-ml retry read_capacity_16 errors
In reply to Mike ChristieThis has read_capacity_16 have scsi-ml retry errors instead of driving them itself.
There are 2 behavior changes with this patch:
1. There is one behavior change where we no longer retry when scsi_execute_cmd returns < 0, but we should be ok. We don't need to retry for failures like the queue being removed, and for the case where there are no tags/reqs since the block layer waits/retries for us. For possible memory allocation failures from blk_rq_map_kern we use GFP_NOIO, so retrying will probably not help.
2. For the specific UAs we checked for and retried, we would get READ_CAPACITY_RETRIES_ON_RESET retries plus whatever retries were left from the main loop's retries. Each UA now gets READ_CAPACITY_RETRIES_ON_RESET reties, and the other errors get up to 3 retries. This is most likely ok, because READ_CAPACITY_RETRIES_ON_RESET is already 10 and is not based on anything specific like a spec or device, so the extra 3 we got from the main loop was probably just an accident and is not going to help.
--- drivers/scsi/sd.c | 108 ++++++++++++++++++++++++++++++---------------- 1 file changed, 71 insertions(+), 37 deletions(-)
drivers/scsi/sd.c +71 -37
@@ -2453,55 +2453,89 @@ static void read_capacity_error(struct scsi_disk *sdkp, struct scsi_device *sdp,static int read_capacity_16 (struct scsi_disk *sdkp,struct scsi_device *sdp,unsigned char *buffer) { -unsigned char cmd[16 ]; -struct scsi_sense_hdr sshdr; -const struct scsi_exec_args exec_args = { - .sshdr = &sshdr, +static const u8 cmd[16 ] = { + [0 ] =SERVICE_ACTION_IN_16 , + [1 ] =SAI_READ_CAPACITY_16 , + [13 ] =RC16_LEN , }; +struct scsi_sense_hdr sshdr;int sense_valid =0 ;int the_result; -int retries =3 , reset_retries =READ_CAPACITY_RETRIES_ON_RESET ;unsigned int alignment;unsigned long long lba;unsigned sector_size; +struct scsi_failure failure_defs[] = { +/* +* Do not retry Invalid Command Operation Code or Invalid +* Field in CDB. +*/ + { + .sense =ILLEGAL_REQUEST , + .asc =0x20 , + .result =SAM_STAT_CHECK_CONDITION , + }, + { + .sense =ILLEGAL_REQUEST , + .asc =0x24 , + .result =SAM_STAT_CHECK_CONDITION , + }, +/* Do not retry Medium Not Present */ + { + .sense =UNIT_ATTENTION , + .asc =0x3A , + .result =SAM_STAT_CHECK_CONDITION , + }, + { + .sense =NOT_READY , + .asc =0x3A , + .result =SAM_STAT_CHECK_CONDITION , + }, +/* Device reset might occur several times so retry a lot */ + { + .sense =UNIT_ATTENTION , + .asc =0x29 , + .allowed =READ_CAPACITY_RETRIES_ON_RESET , + .result =SAM_STAT_CHECK_CONDITION , + }, +/* Any other error not listed above retry 3 times */ + { + .result =SCMD_FAILURE_RESULT_ANY , + .allowed =3 , + }, + {} + }; +struct scsi_failures failures = { + .failure_definitions = failure_defs, + }; +const struct scsi_exec_args exec_args = { + .sshdr = &sshdr, + .failures = &failures, + };if (sdp->no_read_capacity_16)return -EINVAL ; -do { -memset (cmd,0 ,16 ); - cmd[0 ] =SERVICE_ACTION_IN_16 ; - cmd[1 ] =SAI_READ_CAPACITY_16 ; - cmd[13 ] =RC16_LEN ; -memset (buffer,0 ,RC16_LEN ); - - the_result =scsi_execute_cmd (sdp, cmd,REQ_OP_DRV_IN , - buffer,RC16_LEN ,SD_TIMEOUT , - sdkp->max_retries, &exec_args); -if (the_result >0 ) { -if (media_not_present (sdkp, &sshdr)) -return -ENODEV ; +memset (buffer,0 ,RC16_LEN ); - sense_valid =scsi_sense_valid (&sshdr); -if (sense_valid && - sshdr.sense_key ==ILLEGAL_REQUEST && - (sshdr.asc ==0x20 || sshdr.asc ==0x24 ) && - sshdr.ascq ==0x00 ) -/* Invalid Command Operation Code or -* Invalid Field in CDB, just retry -* silently with RC10 */ -return -EINVAL ; -if (sense_valid && - sshdr.sense_key ==UNIT_ATTENTION && - sshdr.asc ==0x29 && sshdr.ascq ==0x00 ) -/* Device reset might occur several times, -* give it one more chance */ -if (--reset_retries >0 ) -continue ; - } - retries--; + the_result =scsi_execute_cmd (sdp, cmd,REQ_OP_DRV_IN , buffer, +RC16_LEN ,SD_TIMEOUT , sdkp->max_retries, + &exec_args); - }while (the_result && retries); +if (the_result >0 ) { +if (media_not_present (sdkp, &sshdr)) +return -ENODEV ; + + sense_valid =scsi_sense_valid (&sshdr); +if (sense_valid && sshdr.sense_key ==ILLEGAL_REQUEST && + (sshdr.asc ==0x20 || sshdr.asc ==0x24 ) && + sshdr.ascq ==0x00 ) { +/* +* Invalid Command Operation Code or Invalid Field in +* CDB, just retry silently with RC10 +*/ +return -EINVAL ; + } + }if (the_result) {sd_print_result (sdkp,"Read Capacity(16) failed" , the_result);
Signature · 1 line
2.34.1
Re: [PATCH v12 04/20] scsi: sd: Have scsi-ml retry read_capacity_16 errors
On 14/11/2023 01:37, Mike Christie wrote:
Feel free to pick up:
drivers/scsi/sd.c static void read_capacity_error(struct scsi_disk *sdkp, struct scsi_device *sdp, · line 2521
Quoted 2 lines
drivers/scsi/sd.c +2
-0+ the_result = scsi_execute_cmd(sdp, cmd, REQ_OP_DRV_IN, buffer, + RC16_LEN, SD_TIMEOUT, sdkp->max_retries,
BTW, some might find it a little confusing that we have scsi_execute_cmd() retries arg as well as being able to pass exec_args.failure, and exec_args.failure may allow us to retry. Could this be improved, even in terms of arg or struct member naming/comments?
Thanks,
John
Quoted 18 lines
drivers/scsi/sd.c +16
-1+ &exec_args); - }while (the_result && retries); +if (the_result >0 ) { +if (media_not_present (sdkp, &sshdr)) +return -ENODEV ; + + sense_valid =scsi_sense_valid (&sshdr); +if (sense_valid && sshdr.sense_key ==ILLEGAL_REQUEST && + (sshdr.asc ==0x20 || sshdr.asc ==0x24 ) && + sshdr.ascq ==0x00 ) { +/* +* Invalid Command Operation Code or Invalid Field in +* CDB, just retry silently with RC10 +*/ +return -EINVAL ; + } + }
Re: [PATCH v12 04/20] scsi: sd: Have scsi-ml retry read_capacity_16 errors
Quoted 9 lines · John Garry
On 14/11/2023 01:37, Mike Christie wrote:
Feel free to pick up:
Reviewed-by John Garry <[email protected]>Quoted 2 lines
+
the_result= scsi_execute_cmd(sdp, cmd,REQ_OP_DRV_IN, buffer, +RC16_LEN,SD_TIMEOUT,sdkp->max_retries,BTW, some might find it a little confusing that we have
scsi_execute_cmd()retries arg as well as being able to pass exec_args.failure, and exec_args.failure may allow us to retry. Could this be improved, even in terms of arg or struct member naming/comments?
Will add some comments.
Martin W, if you are going to ask about this again, the answer is that in a future patchset, we can kill the reties passed directly into scsi_execute_cmd.
We could make scsi_decide_disposition's failures an array of scsi_failure structs that gets checked in scsi_decide_disposition and scsi_check_passthrough. We would need to add a function callout to the scsi_failure struct for some of the more complicated failure handling. That could then be used for some of the other scsi_execute_cmd cases as well. For the normal/fast path case though we would need something to avoid function pointers.
Re: [PATCH v12 04/20] scsi: sd: Have scsi-ml retry read_capacity_16 errors
Quoted 16 lines · Mike Christie
Quoted 9 lines · John Garry
On 14/11/2023 01:37, Mike Christie wrote:
Feel free to pick up:
Reviewed-by John Garry <[email protected]>Quoted 3 lines
+
the_result= scsi_execute_cmd(sdp, cmd,REQ_OP_DRV_IN, buffer,
+RC16_LEN,SD_TIMEOUT,sdkp->max_retries,Quoted 5 lines
BTW, some might find it a little confusing that we have
scsi_execute_cmd()retries arg as well as being able to pass exec_args.failure, and exec_args.failure may allow us to retry. Could this be improved, even in terms of arg or struct member naming/comments?
Quoted 7 lines
Will add some comments.
Martin W, if you are going to ask about this again, the answer is that
in a future patchset, we can kill the reties passed directly intoscsi_execute_cmd.
Did I ask about this? ... I dimly remember ;-)
Quoted 8 lines
We could make scsi_decide_disposition's failures an array of
scsi_failurestructs that gets checked inscsi_decide_dispositionandscsi_check_passthrough. We would need to add a function callout to thescsi_failurestruct for some of the more complicated failure handling. That could then be used for some of the otherscsi_execute_cmd
cases as well. For the normal/fast path case though we would need something to avoid function pointers.
I am not sure if I like this idea. scsi_decide_disposition() is challenging to read already. I am not convinced that converting it into a loop over "struct scsi_failure" would make it easier to understand. I guess we'd need to see how it would look like.
To my understanding, the two retry counts are currently orthogonal, the one in scsi_execute_cmd() representing the standard mid-layer "maybe_retry" case in scsi_decide_disposition, and the the other one representing the additional "high level" passthrough retry. We need to be careful when merging them.
Wrt the callout, I'd actually thought about that when looking at your previous set, but I didn't want to interfere too much. I thought that using callouts might simplify the scsi_failure handling, and might actually make the new code easier to read. I can't judge possible effects on performance.
Cheers,
Martin
PATCH v12 5/20 scsi: Use separate buf for START_STOP in sd_spinup_disk
In reply to Mike ChristieWe currently re-use the cmd buffer for the TUR and START_STOP commands which requires us to reset the buffer when retrying. This has us use separate buffers for the 2 commands so we can make them const and I think it makes it easier to handle for retries but does not add too much extra to the stack use.
--- drivers/scsi/sd.c | 16 +++++++++------- 1 file changed, 9 insertions(+), 7 deletions(-)
drivers/scsi/sd.c +9 -7
@@ -2318,14 +2318,16 @@ sd_spinup_disk(struct scsi_disk *sdkp)* Issue command to spin up drive when not ready */ if (!spintime) { +/* Return immediately and start spin cycle */ +const u8 start_cmd[10 ] = { + [0 ] =START_STOP , + [1 ] =1 , + [4 ] = sdkp->device->start_stop_pwr_cond ? +0x11 :1 , + }; +sd_printk (KERN_NOTICE , sdkp,"Spinning up disk..." ); - cmd[0 ] =START_STOP ; - cmd[1 ] =1 ;/* Return immediately */ -memset ((void *) &cmd[2 ],0 ,8 ); - cmd[4 ] =1 ;/* Start spin cycle */ -if (sdkp->device->start_stop_pwr_cond) - cmd[4 ] |=1 <<4 ; -scsi_execute_cmd (sdkp->device, cmd, +scsi_execute_cmd (sdkp->device, start_cmd,REQ_OP_DRV_IN ,NULL ,0 ,SD_TIMEOUT , sdkp->max_retries, &exec_args);
Signature · 1 line
2.34.1
PATCH v12 6/20 scsi: Have scsi-ml retry sd_spinup_disk errors
In reply to Mike ChristieThis simplifies sd_spinup_disk so scsi-ml retries errors for it. Note that we retried specifically on a UA and also if scsi_status_is_good returned failed which would happen for all check conditions. In this patch we use SCMD_FAILURE_STAT_ANY which will trigger for the same conditions as when scsi_status_is_good returns false and there is status. This will cover all CCs including UAs so there is no explicit failures arrary entry for UAs.
There is one behavior change where we no longer retry when scsi_execute_cmd returns < 0, but we should be ok. We don't need to retry for failures like the queue being removed, and for the case where there are no tags/reqs the block layer waits/retries for us. For possible memory allocation failures from blk_rq_map_kern we use GFP_NOIO, so retrying will probably not help.
We do not handle the outside loop's retries because we want to sleep between tries and we don't support that yet.
--- drivers/scsi/sd.c | 77 +++++++++++++++++++++++++++-------------------- 1 file changed, 45 insertions(+), 32 deletions(-)
drivers/scsi/sd.c +45 -32
@@ -2235,55 +2235,68 @@ static int sd_done(struct scsi_cmnd *SCpnt)static void sd_spinup_disk (struct scsi_disk *sdkp) { -unsigned char cmd[10 ]; +static const u8 cmd[10 ] = {TEST_UNIT_READY };unsigned long spintime_expire =0 ; -int retries, spintime; +int spintime, sense_valid =0 ;unsigned int the_result;struct scsi_sense_hdr sshdr; +struct scsi_failure failure_defs[] = { +/* Do not retry Medium Not Present */ + { + .sense =UNIT_ATTENTION , + .asc =0x3A , + .ascq =SCMD_FAILURE_ASCQ_ANY , + .result =SAM_STAT_CHECK_CONDITION , + }, + { + .sense =NOT_READY , + .asc =0x3A , + .ascq =SCMD_FAILURE_ASCQ_ANY , + .result =SAM_STAT_CHECK_CONDITION , + }, +/* Retry when scsi_status_is_good would return false 3 times */ + { + .result =SCMD_FAILURE_STAT_ANY , + .allowed =3 , + }, + {} + }; +struct scsi_failures failures = { + .failure_definitions = failure_defs, + };const struct scsi_exec_args exec_args = { .sshdr = &sshdr, + .failures = &failures, }; -int sense_valid =0 ; spintime =0 ;/* Spin up drives, as required. Only do this at boot time */ /* Spinup needs to be done for module loads too. */ do { - retries = 0; + bool media_was_present = sdkp->media_present; - do { - bool media_was_present = sdkp->media_present; + scsi_reset_failures(&failures); - cmd[0] = TEST_UNIT_READY; - memset((void *) &cmd[1], 0, 9); + the_result = scsi_execute_cmd(sdkp->device, cmd, REQ_OP_DRV_IN, + NULL, 0, SD_TIMEOUT, + sdkp->max_retries, &exec_args); - the_result = scsi_execute_cmd(sdkp->device, cmd, - REQ_OP_DRV_IN, NULL, 0, - SD_TIMEOUT, - sdkp->max_retries, - &exec_args); - if (the_result > 0) { - /* - * If the drive has indicated to us that it - * doesn't have any media in it, don't bother - * with any more polling. - */ - if (media_not_present(sdkp, &sshdr)) { - if (media_was_present) - sd_printk(KERN_NOTICE, sdkp, - "Media removed, stopped polling\n"); - return; - } - - sense_valid = scsi_sense_valid(&sshdr); + if (the_result > 0) { + /* + * If the drive has indicated to us that it doesn't + * have any media in it, don't bother with any more + * polling. + */ + if (media_not_present(sdkp, &sshdr)) { + if (media_was_present) + sd_printk(KERN_NOTICE, sdkp, + "Media removed, stopped polling\n"); + return; } - retries++; - } while (retries < 3 && - (!scsi_status_is_good(the_result) || - (scsi_status_is_check_condition(the_result) && - sense_valid && sshdr.sense_key == UNIT_ATTENTION))); + sense_valid = scsi_sense_valid(&sshdr); + } if (!scsi_status_is_check_condition(the_result)) { /* no sense, TUR either succeeded or failed
Signature · 1 line
2.34.1
Re: [PATCH v12 06/20] scsi: Have scsi-ml retry sd_spinup_disk errors
On 14/11/2023 01:37, Mike Christie wrote:
Hi Mike,
Quoted 6 lines
This simplifies
sd_spinup_diskso scsi-ml retries errors for it. Note that we retried specifically on a UA and also ifscsi_status_is_goodreturned failed which would happen for all check conditions. In this patch we useSCMD_FAILURE_STAT_ANYwhich will trigger for the same conditions as whenscsi_status_is_goodreturns false and there is status. This will cover all CCs including UAs so there is no explicit failures arrary entry
/s/arrary/array/
Quoted 1 line
for UAs.
But the first failure_defs member is for UNIT_ATTENTION, below, right?
Thanks,
John
Quoted 51 lines
There is one behavior change where we no longer retry when
scsi_execute_cmdreturns < 0, but we should be ok. We don't need to retry for failures like the queue being removed, and for the case where there are no tags/reqs the block layer waits/retries for us. For possible memory allocation failures fromblk_rq_map_kernwe useGFP_NOIO, so retrying will probably not help.We do not handle the outside loop's retries because we want to sleep between tries and we don't support that yet.
Signed-off-by Mike Christie<[email protected]>--- drivers/scsi/sd.c | 77 +++++++++++++++++++++++++++-------------------- 1 file changed, 45 insertions(+), 32 deletions(-)drivers/scsi/sd.c +22
-2@@ -2235,55 +2235,68 @@ static int sd_done(struct scsi_cmnd *SCpnt)static void sd_spinup_disk (struct scsi_disk *sdkp) { -unsigned char cmd[10 ]; +static const u8 cmd[10 ] = {TEST_UNIT_READY };unsigned long spintime_expire =0 ; -int retries, spintime; +int spintime, sense_valid =0 ;unsigned int the_result;struct scsi_sense_hdr sshdr; +struct scsi_failure failure_defs[] = { +/* Do not retry Medium Not Present */ + { + .sense =UNIT_ATTENTION , + .asc =0x3A , + .ascq =SCMD_FAILURE_ASCQ_ANY , + .result =SAM_STAT_CHECK_CONDITION , + }, + { + .sense =NOT_READY , + .asc =0x3A , + .ascq =SCMD_FAILURE_ASCQ_ANY , + .result =SAM_STAT_CHECK_CONDITION , + }, +/* Retry when scsi_status_is_good would return false 3 times */ + { + .result =SCMD_FAILURE_STAT_ANY , + .allowed =3 , + }, + {}
Re: [PATCH v12 06/20] scsi: Have scsi-ml retry sd_spinup_disk errors
Quoted 11 lines · John Garry
On 14/11/2023 01:37, Mike Christie wrote:
Hi Mike,
Quoted 6 lines
This simplifies
sd_spinup_diskso scsi-ml retries errors for it. Note that we retried specifically on a UA and also ifscsi_status_is_goodreturned failed which would happen for all check conditions. In this patch we useSCMD_FAILURE_STAT_ANYwhich will trigger for the same conditions as whenscsi_status_is_goodreturns false and there is status. This will cover all CCs including UAs so there is no explicit failures arrary entry
Quoted 6 lines
/s/arrary/array/
Quoted 1 line
for UAs.
But the first
failure_defsmember is forUNIT_ATTENTION, below, right?
I should not have written "on a UA" above. We want to retry every UA except that first entries in that array.
This first and second entry says if we see it then fail. However, if it's not that specific failure value, then the last entry SCMD_FAILURE_STAT_ANY kicks in and scsi_execute_cmd will retry.
It's so for this chunk:
- the_result = scsi_execute_cmd(sdkp->device, cmd,
- REQ_OP_DRV_IN, NULL, 0, - SD_TIMEOUT, - sdkp->max_retries, - &exec_args);
- if (the_result > 0) {
- /*
- * If the drive has indicated to us that it
- * doesn't have any media in it, don't bother
- * with any more polling.
- */
- if (media_not_present(sdkp, &sshdr)) {
- if (media_was_present)
- sd_printk(KERN_NOTICE, sdkp,
- "Media removed, stopped polling\n");
- return;
- }
we will not retry if we get media_not_present but then retry here:
- } while (retries < 3 &&
- (!scsi_status_is_good(the_result) ||
- (scsi_status_is_check_condition(the_result) &&
- sense_valid && sshdr.sense_key == UNIT_ATTENTION)));
Quoted 21 lines
Quoted 20 lines
+ struct
scsi_failurefailure_defs[] = {
+ /* Do not retry Medium Not Present */
+ {
+ .sense =UNIT_ATTENTION,
+ .asc =0x3A,
+ .ascq =SCMD_FAILURE_ASCQ_ANY,
+ .result =SAM_STAT_CHECK_CONDITION,
+ },
+ {
+ .sense =NOT_READY,
+ .asc =0x3A,
+ .ascq =SCMD_FAILURE_ASCQ_ANY,
+ .result =SAM_STAT_CHECK_CONDITION,
+ },
+ /* Retry whenscsi_status_is_goodwould return false 3 times */ + {
+ .result =SCMD_FAILURE_STAT_ANY,
+ .allowed = 3,
+ },
+ {}
PATCH v12 7/20 scsi: hp_sw: Have scsi-ml retry scsi_execute_cmd errors
In reply to Mike ChristieThis has hp_sw have scsi-ml retry scsi_execute_cmd errors instead of driving them itself.
--- drivers/scsi/device_handler/scsi_dh_hp_sw.c | 49 ++++++++++++++------- 1 file changed, 33 insertions(+), 16 deletions(-)
drivers/scsi/device_handler/scsi_dh_hp_sw.c +33 -16
@@ -46,9 +46,6 @@ static int tur_done(struct scsi_device *sdev, struct hp_sw_dh_data *h,int ret =SCSI_DH_IO ;switch (sshdr->sense_key) { -case UNIT_ATTENTION : - ret =SCSI_DH_IMM_RETRY ; -break ;case NOT_READY :if (sshdr->asc ==0x04 && sshdr->ascq ==2 ) {/*
@@ -85,11 +82,24 @@ static int hp_sw_tur(struct scsi_device *sdev, struct hp_sw_dh_data *h)int ret, res;blk_opf_t opf =REQ_OP_DRV_IN |REQ_FAILFAST_DEV |REQ_FAILFAST_TRANSPORT |REQ_FAILFAST_DRIVER ; +struct scsi_failure failure_defs[] = { + { + .sense =UNIT_ATTENTION , + .asc =SCMD_FAILURE_ASC_ANY , + .ascq =SCMD_FAILURE_ASCQ_ANY , + .allowed =SCMD_FAILURE_NO_LIMIT , + .result =SAM_STAT_CHECK_CONDITION , + }, + {} + }; +struct scsi_failures failures = { + .failure_definitions = failure_defs, + };const struct scsi_exec_args exec_args = { .sshdr = &sshdr, + .failures = &failures, }; -retry: res =scsi_execute_cmd (sdev, cmd, opf,NULL ,0 ,HP_SW_TIMEOUT ,HP_SW_RETRIES , &exec_args);if (res >0 &&scsi_sense_valid (&sshdr)) {
@@ -104,9 +114,6 @@ static int hp_sw_tur(struct scsi_device *sdev, struct hp_sw_dh_data *h) ret =SCSI_DH_IO ; } -if (ret ==SCSI_DH_IMM_RETRY ) - goto retry; -return ret; }
@@ -122,14 +129,31 @@ static int hp_sw_start_stop(struct hp_sw_dh_data *h)struct scsi_sense_hdr sshdr;struct scsi_device *sdev = h->sdev;int res, rc; -int retry_cnt =HP_SW_RETRIES ;blk_opf_t opf =REQ_OP_DRV_IN |REQ_FAILFAST_DEV |REQ_FAILFAST_TRANSPORT |REQ_FAILFAST_DRIVER ; +struct scsi_failure failure_defs[] = { + { +/* +* LUN not ready - manual intervention required +* +* Switch-over in progress, retry. +*/ + .sense =NOT_READY , + .asc =0x04 , + .ascq =0x03 , + .allowed =HP_SW_RETRIES , + .result =SAM_STAT_CHECK_CONDITION , + }, + {} + }; +struct scsi_failures failures = { + .failure_definitions = failure_defs, + };const struct scsi_exec_args exec_args = { .sshdr = &sshdr, + .failures = &failures, }; -retry: res =scsi_execute_cmd (sdev, cmd, opf,NULL ,0 ,HP_SW_TIMEOUT ,HP_SW_RETRIES , &exec_args);if (!res) {
@@ -144,13 +168,6 @@ static int hp_sw_start_stop(struct hp_sw_dh_data *h)switch (sshdr.sense_key) {case NOT_READY :if (sshdr.asc ==0x04 && sshdr.ascq ==3 ) { -/* -* LUN not ready - manual intervention required -* -* Switch-over in progress, retry. -*/ -if (--retry_cnt) - goto retry; rc =SCSI_DH_RETRY ;break ; }
Signature · 1 line
2.34.1
PATCH v12 8/20 scsi: rdac: Have scsi-ml retry send_mode_select errors
In reply to Mike ChristieThis has rdac have scsi-ml retry errors instead of driving them itself.
--- drivers/scsi/device_handler/scsi_dh_rdac.c | 84 ++++++++++++---------- 1 file changed, 46 insertions(+), 38 deletions(-)
drivers/scsi/device_handler/scsi_dh_rdac.c +46 -38
@@ -485,43 +485,17 @@ static int set_mode_select(struct scsi_device *sdev, struct rdac_dh_data *h)static int mode_select_handle_sense (struct scsi_device *sdev,struct scsi_sense_hdr *sense_hdr) { -int err =SCSI_DH_IO ;struct rdac_dh_data *h = sdev->handler_data;if (!scsi_sense_valid (sense_hdr)) - goto done; - -switch (sense_hdr->sense_key) { -case NO_SENSE : -case ABORTED_COMMAND : -case UNIT_ATTENTION : - err =SCSI_DH_RETRY ; -break ; -case NOT_READY : -if (sense_hdr->asc ==0x04 && sense_hdr->ascq ==0x01 ) -/* LUN Not Ready and is in the Process of Becoming -* Ready -*/ - err =SCSI_DH_RETRY ; -break ; -case ILLEGAL_REQUEST : -if (sense_hdr->asc ==0x91 && sense_hdr->ascq ==0x36 ) -/* -* Command Lock contention -*/ - err =SCSI_DH_IMM_RETRY ; -break ; -default : -break ; - } +return SCSI_DH_IO ;RDAC_LOG (RDAC_LOG_FAILOVER , sdev,"array %s, ctlr %d, " "MODE_SELECT returned with sense %02x/%02x/%02x" , (char *) h->ctlr->array_name, h->ctlr->index, sense_hdr->sense_key, sense_hdr->asc, sense_hdr->ascq); -done: -return err; +return SCSI_DH_IO ; }static void send_mode_select (struct work_struct *work)
@@ -530,7 +504,7 @@ static void send_mode_select(struct work_struct *work) container_of(work, struct rdac_controller, ms_work);struct scsi_device *sdev = ctlr->ms_sdev;struct rdac_dh_data *h = sdev->handler_data; -int rc, err, retry_cnt =RDAC_RETRY_COUNT ; +int rc, err;struct rdac_queue_data *tmp, *qdata;LIST_HEAD (list);unsigned char cdb[MAX_COMMAND_SIZE ];
@@ -538,8 +512,49 @@ static void send_mode_select(struct work_struct *work)unsigned int data_size;blk_opf_t opf =REQ_OP_DRV_OUT |REQ_FAILFAST_DEV |REQ_FAILFAST_TRANSPORT |REQ_FAILFAST_DRIVER ; +struct scsi_failure failure_defs[] = { + { + .sense =NO_SENSE , + .asc =SCMD_FAILURE_ASC_ANY , + .ascq =SCMD_FAILURE_ASCQ_ANY , + .result =SAM_STAT_CHECK_CONDITION , + }, + { + .sense =ABORTED_COMMAND , + .asc =SCMD_FAILURE_ASC_ANY , + .ascq =SCMD_FAILURE_ASCQ_ANY , + .result =SAM_STAT_CHECK_CONDITION , + }, + { + .sense =UNIT_ATTENTION , + .asc =SCMD_FAILURE_ASC_ANY , + .ascq =SCMD_FAILURE_ASCQ_ANY , + .result =SAM_STAT_CHECK_CONDITION , + }, +/* LUN Not Ready and is in the Process of Becoming Ready */ + { + .sense =NOT_READY , + .asc =0x04 , + .ascq =0x01 , + .result =SAM_STAT_CHECK_CONDITION , + }, +/* Command Lock contention */ + { + .sense =ILLEGAL_REQUEST , + .asc =0x91 , + .ascq =0x36 , + .allowed =SCMD_FAILURE_NO_LIMIT , + .result =SAM_STAT_CHECK_CONDITION , + }, + {} + }; +struct scsi_failures failures = { + .total_allowed =RDAC_RETRY_COUNT , + .failure_definitions = failure_defs, + };const struct scsi_exec_args exec_args = { .sshdr = &sshdr, + .failures = &failures, };spin_lock (&ctlr->ms_lock);
@@ -548,15 +563,12 @@ static void send_mode_select(struct work_struct *work) ctlr->ms_sdev =NULL ;spin_unlock (&ctlr->ms_lock); - retry:memset (cdb,0 ,sizeof (cdb)); data_size =rdac_failover_get (ctlr, &list, cdb); -RDAC_LOG (RDAC_LOG_FAILOVER , sdev,"array %s, ctlr %d, " -"%s MODE_SELECT command" , - (char *) h->ctlr->array_name, h->ctlr->index, - (retry_cnt ==RDAC_RETRY_COUNT ) ?"queueing" :"retrying" ); +RDAC_LOG (RDAC_LOG_FAILOVER , sdev,"array %s, ctlr %d, queueing MODE_SELECT command" , + (char *)h->ctlr->array_name, h->ctlr->index); rc =scsi_execute_cmd (sdev, cdb, opf, &h->ctlr->mode_select, data_size,RDAC_TIMEOUT *HZ ,RDAC_RETRIES , &exec_args);
@@ -570,10 +582,6 @@ static void send_mode_select(struct work_struct *work) err =SCSI_DH_IO ; }else { err =mode_select_handle_sense (sdev, &sshdr); -if (err ==SCSI_DH_RETRY && retry_cnt--) - goto retry; -if (err ==SCSI_DH_IMM_RETRY ) - goto retry; }list_for_each_entry_safe (qdata, tmp, &list, entry) {
Signature · 1 line
2.34.1
PATCH v12 9/20 scsi: spi: Have scsi-ml retry spi_execute UAs
In reply to Mike ChristieThis has spi_execute have scsi-ml retry UAs instead of driving them.
--- drivers/scsi/scsi_transport_spi.c | 35 ++++++++++++++++--------------- 1 file changed, 18 insertions(+), 17 deletions(-)
drivers/scsi/scsi_transport_spi.c +18 -17
@@ -108,29 +108,30 @@ static int spi_execute(struct scsi_device *sdev, const void *cmd, enum req_op op, void *buffer, unsigned int bufflen, struct scsi_sense_hdr *sshdr) { - int i, result; -struct scsi_sense_hdr sshdr_tmp; blk_opf_t opf = op | REQ_FAILFAST_DEV | REQ_FAILFAST_TRANSPORT |REQ_FAILFAST_DRIVER ; +struct scsi_failure failure_defs[] = { + { + .sense =UNIT_ATTENTION , + .asc =SCMD_FAILURE_ASC_ANY , + .ascq =SCMD_FAILURE_ASCQ_ANY , + .allowed =DV_RETRIES , + .result =SAM_STAT_CHECK_CONDITION , + }, + {} + }; +struct scsi_failures failures = { + .failure_definitions = failure_defs, + };const struct scsi_exec_args exec_args = { +/* bypass the SDEV_QUIESCE state with BLK_MQ_REQ_PM */ .req_flags =BLK_MQ_REQ_PM , - .sshdr = sshdr ? : &sshdr_tmp, + .sshdr = sshdr, + .failures = &failures, }; - sshdr = exec_args.sshdr; - -for (i =0 ; i <DV_RETRIES ; i++) { -/* -* The purpose of the RQF_PM flag below is to bypass the -* SDEV_QUIESCE state. -*/ - result =scsi_execute_cmd (sdev, cmd, opf, buffer, bufflen, -DV_TIMEOUT ,1 , &exec_args); -if (result <0 || !scsi_sense_valid (sshdr) || - sshdr->sense_key !=UNIT_ATTENTION ) -break ; - } -return result; +return scsi_execute_cmd (sdev, cmd, opf, buffer, bufflen,DV_TIMEOUT ,1 , + &exec_args); } static struct {
Signature · 1 line
2.34.1
PATCH v12 10/20 scsi: sd: Have scsi-ml retry sd_sync_cache errors
In reply to Mike ChristieThis has sd_sync_cache have scsi-ml retry errors instead of driving them itself.
There is one behavior change where we no longer retry when scsi_execute_cmd returns < 0, but we should be ok. We don't need to retry for failures like the queue being removed, and for the case where there are no tags/reqs the block layer waits/retries for us. For possible memory allocation failures from blk_rq_map_kern we use GFP_NOIO, so retrying will probably not help.
--- drivers/scsi/sd.c | 35 +++++++++++++++++------------------ 1 file changed, 17 insertions(+), 18 deletions(-)
drivers/scsi/sd.c +17 -18
@@ -1645,36 +1645,35 @@ static unsigned int sd_check_events(struct gendisk *disk, unsigned int clearing)static int sd_sync_cache (struct scsi_disk *sdkp) { -int retries, res; +int res;struct scsi_device *sdp = sdkp->device;const int timeout = sdp->request_queue->rq_timeout *SD_FLUSH_TIMEOUT_MULTIPLIER ; +/* Leave the rest of the command zero to indicate flush everything. */ +const unsigned char cmd[16 ] = { sdp->use_16_for_sync ? +SYNCHRONIZE_CACHE_16 :SYNCHRONIZE_CACHE };struct scsi_sense_hdr sshdr; +struct scsi_failure failure_defs[] = { + { + .allowed =3 , + .result =SCMD_FAILURE_RESULT_ANY , + }, + {} + }; +struct scsi_failures failures = { + .failure_definitions = failure_defs, + };const struct scsi_exec_args exec_args = { .req_flags =BLK_MQ_REQ_PM , .sshdr = &sshdr, + .failures = &failures, };if (!scsi_device_online (sdp))return -ENODEV ; -for (retries =3 ; retries >0 ; --retries) { -unsigned char cmd[16 ] = {0 }; - -if (sdp->use_16_for_sync) - cmd[0 ] =SYNCHRONIZE_CACHE_16 ; -else - cmd[0 ] =SYNCHRONIZE_CACHE ; -/* -* Leave the rest of the command zero to indicate -* flush everything. -*/ - res =scsi_execute_cmd (sdp, cmd,REQ_OP_DRV_IN ,NULL ,0 , - timeout, sdkp->max_retries, &exec_args); -if (res ==0 ) -break ; - } - + res =scsi_execute_cmd (sdp, cmd,REQ_OP_DRV_IN ,NULL ,0 , timeout, + sdkp->max_retries, &exec_args);if (res) {sd_print_result (sdkp,"Synchronize Cache(10) failed" , res);
Signature · 1 line
2.34.1
PATCH v12 11/20 scsi: ch: Remove unit_attention
In reply to Mike Christieunit_attention is not used so remove it.
--- drivers/scsi/ch.c | 2 -- 1 file changed, 2 deletions(-)
drivers/scsi/ch.c +0 -2
@@ -113,7 +113,6 @@ typedef struct {struct scsi_device **dt;/* ptrs to data transfer elements */ u_int firsts[CH_TYPES ];u_int counts[CH_TYPES ]; -u_int unit_attention;u_int voltags;struct mutex lock; } scsi_changer;
@@ -208,7 +207,6 @@ ch_do_scsi(scsi_changer *ch, unsigned char *cmd, int cmd_len,switch (sshdr.sense_key) {case UNIT_ATTENTION : - ch->unit_attention =1 ;if (retries++ <3 ) goto retry;break ;
Signature · 1 line
2.34.1
PATCH v12 12/20 scsi: ch: Have scsi-ml retry ch_do_scsi UAs
In reply to Mike ChristieThis has ch_do_scsi have scsi-ml retry UAs instead of driving them itself.
--- drivers/scsi/ch.c | 25 +++++++++++++++---------- 1 file changed, 15 insertions(+), 10 deletions(-)
drivers/scsi/ch.c +15 -10
@@ -185,17 +185,29 @@ static int ch_do_scsi(scsi_changer *ch, unsigned char *cmd, int cmd_len, void *buffer, unsigned int buflength, enum req_op op) { -int errno, retries =0 , timeout, result; +int errno =0 , timeout, result;struct scsi_sense_hdr sshdr; +struct scsi_failure failure_defs[] = { + { + .sense =UNIT_ATTENTION , + .asc =SCMD_FAILURE_ASC_ANY , + .ascq =SCMD_FAILURE_ASCQ_ANY , + .allowed =3 , + .result =SAM_STAT_CHECK_CONDITION , + }, + {} + }; +struct scsi_failures failures = { + .failure_definitions = failure_defs, + };const struct scsi_exec_args exec_args = { .sshdr = &sshdr, + .failures = &failures, }; timeout = (cmd[0 ] ==INITIALIZE_ELEMENT_STATUS ) ? timeout_init : timeout_move; - retry: - errno =0 ; result =scsi_execute_cmd (ch->device, cmd, op, buffer, buflength, timeout *HZ ,MAX_RETRIES , &exec_args);if (result <0 )
@@ -204,13 +216,6 @@ ch_do_scsi(scsi_changer *ch, unsigned char *cmd, int cmd_len,if (debug)scsi_print_sense_hdr (ch->device, ch->name, &sshdr); errno =ch_find_errno (&sshdr); - -switch (sshdr.sense_key) { -case UNIT_ATTENTION : -if (retries++ <3 ) - goto retry; -break ; - } }return errno; }
Signature · 1 line
2.34.1
PATCH v12 13/20 scsi: Have scsi-ml retry scsi_mode_sense UAs
In reply to Mike ChristieThis has scsi_mode_sense have scsi-ml retry UAs instead of driving them itself.
--- drivers/scsi/scsi_lib.c | 22 +++++++++++++++------- 1 file changed, 15 insertions(+), 7 deletions(-)
drivers/scsi/scsi_lib.c +15 -7
@@ -2262,11 +2262,25 @@ scsi_mode_sense(struct scsi_device *sdev, int dbd, int modepage, int subpage,unsigned char cmd[12 ];int use_10_for_ms;int header_length; -int result, retry_count = retries; +int result;struct scsi_sense_hdr my_sshdr; +struct scsi_failure failure_defs[] = { + { + .sense =UNIT_ATTENTION , + .asc =SCMD_FAILURE_ASC_ANY , + .ascq =SCMD_FAILURE_ASCQ_ANY , + .allowed = retries, + .result =SAM_STAT_CHECK_CONDITION , + }, + {} + }; +struct scsi_failures failures = { + .failure_definitions = failure_defs, + };const struct scsi_exec_args exec_args = {/* caller might not be interested in sense, but we need it */ .sshdr = sshdr ? : &my_sshdr, + .failures = &failures, };memset (data,0 ,sizeof (*data));
@@ -2328,12 +2342,6 @@ scsi_mode_sense(struct scsi_device *sdev, int dbd, int modepage, int subpage, goto retry; } } -if (scsi_status_is_check_condition (result) && - sshdr->sense_key ==UNIT_ATTENTION && - retry_count) { - retry_count--; - goto retry; - } }return -EIO ; }
Signature · 1 line
2.34.1
PATCH v12 14/20 scsi: Have scsi-ml retry scsi_report_lun_scan errors
In reply to Mike ChristieThis has scsi_report_lun_scan have scsi-ml retry errors instead of driving them itself.
There is one behavior change where we no longer retry when scsi_execute_cmd returns < 0, but we should be ok. We don't need to retry for failures like the queue being removed, and for the case where there are no tags/reqs the block layer waits/retries for us. For possible memory allocation failures from blk_rq_map_kern we use GFP_NOIO, so retrying will probably not help.
--- drivers/scsi/scsi_scan.c | 57 +++++++++++++++++++++++----------------- 1 file changed, 33 insertions(+), 24 deletions(-)
drivers/scsi/scsi_scan.c +33 -24
@@ -1416,14 +1416,34 @@ static int scsi_report_lun_scan(struct scsi_target *starget, blist_flags_t bflagunsigned int length;u64 lun;unsigned int num_luns; -unsigned int retries;int result;struct scsi_lun *lunp, *lun_data; -struct scsi_sense_hdr sshdr;struct scsi_device *sdev;struct Scsi_Host *shost =dev_to_shost (&starget->dev); +struct scsi_failure failure_defs[] = { + { + .sense =UNIT_ATTENTION , + .asc =SCMD_FAILURE_ASC_ANY , + .ascq =SCMD_FAILURE_ASCQ_ANY , + .result =SAM_STAT_CHECK_CONDITION , + }, +/* Fail all CCs except the UA above */ + { + .sense =SCMD_FAILURE_SENSE_ANY , + .result =SAM_STAT_CHECK_CONDITION , + }, +/* Retry any other errors not listed above */ + { + .result =SCMD_FAILURE_RESULT_ANY , + }, + {} + }; +struct scsi_failures failures = { + .total_allowed =3 , + .failure_definitions = failure_defs, + };const struct scsi_exec_args exec_args = { - .sshdr = &sshdr, + .failures = &failures, };int ret =0 ;
@@ -1494,29 +1514,18 @@ static int scsi_report_lun_scan(struct scsi_target *starget, blist_flags_t bflag* should come through as a check condition, and will not generate * a retry. */ -for (retries =0 ; retries <3 ; retries++) { -SCSI_LOG_SCAN_BUS (3 ,sdev_printk (KERN_INFO , sdev, -"scsi scan: Sending REPORT LUNS to (try %d)\n" , - retries)); - - result =scsi_execute_cmd (sdev, scsi_cmd,REQ_OP_DRV_IN , - lun_data, length, -SCSI_REPORT_LUNS_TIMEOUT ,3 , - &exec_args); +scsi_reset_failures (&failures); -SCSI_LOG_SCAN_BUS (3 ,sdev_printk (KERN_INFO , sdev, -"scsi scan: REPORT LUNS" -" %s (try %d) result 0x%x\n" , - result ?"failed" :"successful" , - retries, result)); -if (result ==0 ) -break ; -else if (scsi_sense_valid (&sshdr)) { -if (sshdr.sense_key !=UNIT_ATTENTION ) -break ; - } - } +SCSI_LOG_SCAN_BUS (3 ,sdev_printk (KERN_INFO , sdev, +"scsi scan: Sending REPORT LUNS\n" )); + + result =scsi_execute_cmd (sdev, scsi_cmd,REQ_OP_DRV_IN , lun_data, + length,SCSI_REPORT_LUNS_TIMEOUT ,3 , + &exec_args); +SCSI_LOG_SCAN_BUS (3 ,sdev_printk (KERN_INFO , sdev, +"scsi scan: REPORT LUNS %s result 0x%x\n" , + result ?"failed" :"successful" , result));if (result) {/* * The device probably does not support a REPORT LUN command
Signature · 1 line
2.34.1
PATCH v12 15/20 scsi: sd: Have pr commands retry UAs
In reply to Mike ChristieIt's common to get a UA when doing PR commands. It could be due to a target restarting, transport level relogin or other PR commands like a release causing it. The upper layers don't get the sense and in some cases have no idea if it's a SCSI device, so this has the sd layer retry.
--- drivers/scsi/sd.c | 28 ++++++++++++++++++++++++++++ 1 file changed, 28 insertions(+)
drivers/scsi/sd.c +28 -0
@@ -1800,8 +1800,22 @@ static int sd_pr_in_command(struct block_device *bdev, u8 sa,struct scsi_device *sdev = sdkp->device;struct scsi_sense_hdr sshdr;u8 cmd[10 ] = {PERSISTENT_RESERVE_IN , sa }; +struct scsi_failure failure_defs[] = { + { + .sense =UNIT_ATTENTION , + .asc =SCMD_FAILURE_ASC_ANY , + .ascq =SCMD_FAILURE_ASCQ_ANY , + .allowed =5 , + .result =SAM_STAT_CHECK_CONDITION , + }, + {} + }; +struct scsi_failures failures = { + .failure_definitions = failure_defs, + };const struct scsi_exec_args exec_args = { .sshdr = &sshdr, + .failures = &failures, };int result;
@@ -1888,8 +1902,22 @@ static int sd_pr_out_command(struct block_device *bdev, u8 sa, u64 key,struct scsi_disk *sdkp =scsi_disk (bdev->bd_disk);struct scsi_device *sdev = sdkp->device;struct scsi_sense_hdr sshdr; +struct scsi_failure failure_defs[] = { + { + .sense =UNIT_ATTENTION , + .asc =SCMD_FAILURE_ASC_ANY , + .ascq =SCMD_FAILURE_ASCQ_ANY , + .allowed =5 , + .result =SAM_STAT_CHECK_CONDITION , + }, + {} + }; +struct scsi_failures failures = { + .failure_definitions = failure_defs, + };const struct scsi_exec_args exec_args = { .sshdr = &sshdr, + .failures = &failures, };int result;u8 cmd[16 ] = {0 , };
Signature · 1 line
2.34.1
PATCH v12 16/20 scsi: sd: Have scsi-ml retry read_capacity_10 errors
In reply to Mike ChristieThis has read_capacity_10 have scsi-ml retry errors instead of driving them itself.
There are 2 behavior changes with this patch:
1. There is one behavior change where we no longer retry when scsi_execute_cmd returns < 0, but we should be ok. We don't need to retry for failures like the queue being removed, and for the case where there are no tags/reqs since the block layer waits/retries for us. For possible memory allocation failures from blk_rq_map_kern we use GFP_NOIO, so retrying will probably not help.
2. For the specific UAs we checked for and retried, we would get READ_CAPACITY_RETRIES_ON_RESET retries plus whatever retries were left from the main loop's retries. Each UA now gets READ_CAPACITY_RETRIES_ON_RESET reties, and the other errors get up to 3 retries. This is most likely ok, because READ_CAPACITY_RETRIES_ON_RESET is already 10 and is not based on anything specific like a spec or device, so the extra 3 we got from the main loop was probably just an accident and is not going to help.
--- drivers/scsi/sd.c | 62 +++++++++++++++++++++++++++++------------------ 1 file changed, 39 insertions(+), 23 deletions(-)
drivers/scsi/sd.c +39 -23
@@ -2622,42 +2622,58 @@ static int read_capacity_16(struct scsi_disk *sdkp, struct scsi_device *sdp,static int read_capacity_10 (struct scsi_disk *sdkp,struct scsi_device *sdp,unsigned char *buffer) { -unsigned char cmd[16 ]; +static const u8 cmd[10 ] = {READ_CAPACITY };struct scsi_sense_hdr sshdr; +struct scsi_failure failure_defs[] = { +/* Do not retry Medium Not Present */ + { + .sense =UNIT_ATTENTION , + .asc =0x3A , + .result =SAM_STAT_CHECK_CONDITION , + }, + { + .sense =NOT_READY , + .asc =0x3A , + .result =SAM_STAT_CHECK_CONDITION , + }, +/* Device reset might occur several times so retry a lot */ + { + .sense =UNIT_ATTENTION , + .asc =0x29 , + .allowed =READ_CAPACITY_RETRIES_ON_RESET , + .result =SAM_STAT_CHECK_CONDITION , + }, +/* Any other error not listed above retry 3 times */ + { + .result =SCMD_FAILURE_RESULT_ANY , + .allowed =3 , + }, + {} + }; +struct scsi_failures failures = { + .failure_definitions = failure_defs, + };const struct scsi_exec_args exec_args = { .sshdr = &sshdr, + .failures = &failures, };int sense_valid =0 ;int the_result; -int retries =3 , reset_retries =READ_CAPACITY_RETRIES_ON_RESET ;sector_t lba;unsigned sector_size; -do { - cmd[0 ] =READ_CAPACITY ; -memset (&cmd[1 ],0 ,9 ); -memset (buffer,0 ,8 ); +memset (buffer,0 ,8 ); + + the_result =scsi_execute_cmd (sdp, cmd,REQ_OP_DRV_IN , buffer, +8 ,SD_TIMEOUT , sdkp->max_retries, + &exec_args); - the_result =scsi_execute_cmd (sdp, cmd,REQ_OP_DRV_IN , buffer, -8 ,SD_TIMEOUT , sdkp->max_retries, - &exec_args); +if (the_result >0 ) { + sense_valid =scsi_sense_valid (&sshdr);if (media_not_present (sdkp, &sshdr))return -ENODEV ; - -if (the_result >0 ) { - sense_valid =scsi_sense_valid (&sshdr); -if (sense_valid && - sshdr.sense_key ==UNIT_ATTENTION && - sshdr.asc ==0x29 && sshdr.ascq ==0x00 ) -/* Device reset might occur several times, -* give it one more chance */ -if (--reset_retries >0 ) -continue ; - } - retries--; - - }while (the_result && retries); + }if (the_result) {sd_print_result (sdkp,"Read Capacity(10) failed" , the_result);
Signature · 1 line
2.34.1
PATCH v12 17/20 scsi: ses: Have scsi-ml retry scsi_execute_cmd errors
In reply to Mike ChristieThis has ses have scsi-ml retry scsi_execute_cmd errors instead of driving them itself.
--- drivers/scsi/ses.c | 66 ++++++++++++++++++++++++++++++++-------------- 1 file changed, 46 insertions(+), 20 deletions(-)
drivers/scsi/ses.c +46 -20
@@ -87,19 +87,32 @@ static int ses_recv_diag(struct scsi_device *sdev, int page_code, 0 };unsigned char recv_page_code; -unsigned int retries =SES_RETRIES ; -struct scsi_sense_hdr sshdr; +struct scsi_failure failure_defs[] = { + { + .sense =UNIT_ATTENTION , + .asc =0x29 , + .ascq =SCMD_FAILURE_ASCQ_ANY , + .allowed =SES_RETRIES , + .result =SAM_STAT_CHECK_CONDITION , + }, + { + .sense =NOT_READY , + .asc =SCMD_FAILURE_ASC_ANY , + .ascq =SCMD_FAILURE_ASCQ_ANY , + .allowed =SES_RETRIES , + .result =SAM_STAT_CHECK_CONDITION , + }, + {} + }; +struct scsi_failures failures = { + .failure_definitions = failure_defs, + };const struct scsi_exec_args exec_args = { - .sshdr = &sshdr, + .failures = &failures, }; -do { - ret =scsi_execute_cmd (sdev, cmd,REQ_OP_DRV_IN , buf, bufflen, -SES_TIMEOUT ,1 , &exec_args); - }while (ret >0 && --retries &&scsi_sense_valid (&sshdr) && - (sshdr.sense_key ==NOT_READY || - (sshdr.sense_key ==UNIT_ATTENTION && sshdr.asc ==0x29 ))); - + ret =scsi_execute_cmd (sdev, cmd,REQ_OP_DRV_IN , buf, bufflen, +SES_TIMEOUT ,1 , &exec_args);if (unlikely (ret))return ret;
@@ -131,19 +144,32 @@ static int ses_send_diag(struct scsi_device *sdev, int page_code, bufflen &0xff , 0 }; -struct scsi_sense_hdr sshdr; -unsigned int retries =SES_RETRIES ; +struct scsi_failure failure_defs[] = { + { + .sense =UNIT_ATTENTION , + .asc =0x29 , + .ascq =SCMD_FAILURE_ASCQ_ANY , + .allowed =SES_RETRIES , + .result =SAM_STAT_CHECK_CONDITION , + }, + { + .sense =NOT_READY , + .asc =SCMD_FAILURE_ASC_ANY , + .ascq =SCMD_FAILURE_ASCQ_ANY , + .allowed =SES_RETRIES , + .result =SAM_STAT_CHECK_CONDITION , + }, + {} + }; +struct scsi_failures failures = { + .failure_definitions = failure_defs, + };const struct scsi_exec_args exec_args = { - .sshdr = &sshdr, + .failures = &failures, }; -do { - result =scsi_execute_cmd (sdev, cmd,REQ_OP_DRV_OUT , buf, - bufflen,SES_TIMEOUT ,1 , &exec_args); - }while (result >0 && --retries &&scsi_sense_valid (&sshdr) && - (sshdr.sense_key ==NOT_READY || - (sshdr.sense_key ==UNIT_ATTENTION && sshdr.asc ==0x29 ))); - + result =scsi_execute_cmd (sdev, cmd,REQ_OP_DRV_OUT , buf, bufflen, +SES_TIMEOUT ,1 , &exec_args);if (result)sdev_printk (KERN_ERR , sdev,"SEND DIAGNOSTIC result: %8x\n" , result);
Signature · 1 line
2.34.1
PATCH v12 18/20 scsi: sr: Have scsi-ml retry get_sectorsize errors
In reply to Mike ChristieThis has get_sectorsize have scsi-ml retry errors instead of driving them itself.
There is one behavior change where we no longer retry when scsi_execute_cmd returns < 0, but we should be ok. We don't need to retry for failures like the queue being removed, and for the case where there are no tags/reqs the block layer waits/retries for us. For possible memory allocation failures from blk_rq_map_kern we use GFP_NOIO, so retrying will probably not help.
--- drivers/scsi/sr.c | 38 ++++++++++++++++++++------------------ 1 file changed, 20 insertions(+), 18 deletions(-)
drivers/scsi/sr.c +20 -18
@@ -717,27 +717,29 @@ static int sr_probe(struct device *dev)static void get_sectorsize (struct scsi_cd *cd) { -unsigned char cmd[10 ]; -unsigned char buffer[8 ]; -int the_result, retries =3 ; +static const u8 cmd[10 ] = {READ_CAPACITY }; +unsigned char buffer[8 ] = { }; +int the_result;int sector_size;struct request_queue *queue; +struct scsi_failure failure_defs[] = { + { + .result =SCMD_FAILURE_RESULT_ANY , + .allowed =3 , + }, + {} + }; +struct scsi_failures failures = { + .failure_definitions = failure_defs, + }; +const struct scsi_exec_args exec_args = { + .failures = &failures, + }; -do { - cmd[0 ] =READ_CAPACITY ; -memset ((void *) &cmd[1 ],0 ,9 ); -memset (buffer,0 ,sizeof (buffer)); - -/* Do the command and wait.. */ - the_result =scsi_execute_cmd (cd->device, cmd,REQ_OP_DRV_IN , - buffer,sizeof (buffer), -SR_TIMEOUT ,MAX_RETRIES ,NULL ); - - retries--; - - }while (the_result && retries); - - +/* Do the command and wait.. */ + the_result =scsi_execute_cmd (cd->device, cmd,REQ_OP_DRV_IN , buffer, +sizeof (buffer),SR_TIMEOUT ,MAX_RETRIES , + &exec_args);if (the_result) { cd->capacity =0x1fffff ; sector_size =2048 ;/* A guess, just in case */
Signature · 1 line
2.34.1
PATCH v12 19/20 scsi: ufs: Have scsi-ml retry start stop errors
In reply to Mike ChristieThis has scsi-ml retry errors instead of driving them itself.
--- drivers/ufs/core/ufshcd.c | 22 ++++++++++++---------- 1 file changed, 12 insertions(+), 10 deletions(-)
drivers/ufs/core/ufshcd.c +12 -10
@@ -9384,7 +9384,17 @@ static int ufshcd_execute_start_stop(struct scsi_device *sdev, struct scsi_sense_hdr *sshdr) {const unsigned char cdb[6 ] = {START_STOP ,0 ,0 ,0 , pwr_mode <<4 ,0 }; +struct scsi_failure failure_defs[] = { + { + .allowed =2 , + .result =SCMD_FAILURE_RESULT_ANY , + }, + }; +struct scsi_failures failures = { + .failure_definitions = failure_defs, + };const struct scsi_exec_args args = { + .failures = &failures, .sshdr = sshdr, .req_flags =BLK_MQ_REQ_PM , .scmd_flags =SCMD_FAIL_IF_RECOVERING ,
@@ -9410,7 +9420,7 @@ static int ufshcd_set_dev_pwr_mode(struct ufs_hba *hba,struct scsi_sense_hdr sshdr;struct scsi_device *sdp;unsigned long flags; -int ret, retries; +int ret;spin_lock_irqsave (hba->host->host_lock, flags); sdp = hba->ufs_device_wlun;
@@ -9436,15 +9446,7 @@ static int ufshcd_set_dev_pwr_mode(struct ufs_hba *hba,* callbacks hence set the RQF_PM flag so that it doesn't resume the * already suspended childs. */ -for (retries =3 ; retries >0 ; --retries) { - ret =ufshcd_execute_start_stop (sdp, pwr_mode, &sshdr); -/* -* scsi_execute() only returns a negative value if the request -* queue is dying. -*/ -if (ret <=0 ) -break ; - } + ret =ufshcd_execute_start_stop (sdp, pwr_mode, &sshdr);if (ret) { sdev_printk(KERN_WARNING, sdp, "START_STOP failed for power mode: %d, result %x\n",
Signature · 1 line
2.34.1
PATCH v12 20/20 scsi: Add kunit tests for scsi_check_passthrough
In reply to Mike ChristieAdd some kunit tests for scsi_check_passthrough so we can easily make sure we are hitting the cases it's difficult to replicate in hardware or even scsi_debug.
--- drivers/scsi/Kconfig | 9 + drivers/scsi/scsi_lib.c | 4 + drivers/scsi/scsi_lib_test.c | 330 +++++++++++++++++++++++++++++++++++ 3 files changed, 343 insertions(+) create mode 100644 drivers/scsi/scsi_lib_test.c
drivers/scsi/Kconfig +9 -0
@@ -67,6 +67,15 @@ config SCSI_PROC_FS If unsure say Y. +config SCSI_KUNIT_TEST + tristate "KUnit tests for SCSI Mid Layer" if !KUNIT_ALL_TESTS + depends on KUNIT + default KUNIT_ALL_TESTS + help + Run SCSI Mid Layer's KUnit tests. + + If unsure say N. + comment "SCSI support type (disk, tape, CD-ROM)" depends on SCSI
drivers/scsi/scsi_lib.c +4 -0
@@ -3434,3 +3434,7 @@ void scsi_build_sense(struct scsi_cmnd *scmd, int desc, u8 key, u8 asc, u8 ascq) scmd->result =SAM_STAT_CHECK_CONDITION ; }EXPORT_SYMBOL_GPL (scsi_build_sense); + +#ifdef CONFIG_SCSI_KUNIT_TEST +#include "scsi_lib_test.c" +#endif
drivers/scsi/scsi_lib_test.c new file +330 -0
330 lines not on this page · raw message
Signature · 1 line
2.34.1
Bart Van Assche
reviewerRe: [PATCH v12 20/20] scsi: Add kunit tests for scsi_check_passthrough
Quoted 2 lines · Mike Christie
Add some kunit tests for
scsi_check_passthroughso we can easily make sure we are hitting the cases it's difficult to replicate in hardware or even
^^^^^^^^^^
It seems like the words "for which" are missing here?
drivers/scsi/Kconfig config SCSI_PROC_FS · line 78
Quoted 9 lines
drivers/scsi/Kconfig +9
-0+config SCSI_KUNIT_TEST + tristate "KUnit tests for SCSI Mid Layer" if !KUNIT_ALL_TESTS + depends on KUNIT + default KUNIT_ALL_TESTS + help + Run SCSI Mid Layer's KUnit tests. + + If unsure say N. +
Is a help text required for KUNIT Kconfig entries or is this something that can be left out?
Please rename SCSI_KUNIT_TEST into SCSI_LIB_KUNIT_TEST such that different unit tests can be selected individually. More tests will be added by my patch series that improves zoned write performance.
Thanks,
Bart.
Quoted 2 lines · Mike Christie
The following patches were made over Martin's 6.7 staging branch which contains a sd change that this patch requires.
Hi Mike,
It would be nice if we could apply to 6.8 staging - was the sd.c change not in v6.7-rc1?
Cheers,
John
Quoted 8 lines · John Garry
Quoted 2 lines · Mike Christie
The following patches were made over Martin's 6.7 staging branch which contains a sd change that this patch requires.
Hi Mike,
It would be nice if we could apply to 6.8 staging - was the
sd.cchange not in v6.7-rc1?
Staging didn't exist when I posted this.
It exists now, but is missing:
https://lore.kernel.org/linux-scsi/[email protected]/T/#u
so will not apply to 6.8.
I was actually shooting for 6.9 so I'll figure it out by then.