dt-bindings: tc358775: Add support for tc358765
Subsystems (4)
PATCH 1/6 dt-bindings: tc358775: Add support for tc358765
The tc358765 is similar to tc358775 except for the stdby-gpios.
--- .../display/bridge/toshiba,tc358775.yaml | 17 ++++++++++++++--- 1 file changed, 14 insertions(+), 3 deletions(-)
Documentation/devicetree/bindings/display/bridge/toshiba,tc358775.yaml +14 -3
@@ -10,7 +10,7 @@ maintainers: - Vinay Simha BN <[email protected]> description: | - This binding supports DSI to LVDS bridge TC358775 + This binding supports DSI to LVDS bridges TC358765 and TC358775 MIPI DSI-RX Data 4-lane, CLK 1-lane with data rates up to 800 Mbps/lane. Video frame size:
@@ -21,7 +21,9 @@ description: | properties: compatible: - const: toshiba,tc358775 + enum: + - toshiba,tc358765 + - toshiba,tc358775 reg: maxItems: 1
@@ -70,12 +72,21 @@ required: - reg - vdd-supply - vddio-supply - - stby-gpios - reset-gpios - ports additionalProperties: false +allOf: + - if: + properties: + compatible: + contains: + const: toshiba,tc358775 + then: + required: + - stby-gpios + examples: - | #include <dt-bindings/gpio/gpio.h>
Signature · 1 line
2.42.1
PATCH 2/6 drm/bridge: tc358775: Fix getting dsi host data lanes
The current code assume hardcoded dsi host endpoint 1, which may not be the case. Let's fix that and simplify the code by getting the dsi endpoint with of_graph_get_remote_endpoint() that does not assume any endpoint numbering.
--- drivers/gpu/drm/bridge/tc358775.c | 16 ++++------------ 1 file changed, 4 insertions(+), 12 deletions(-)
drivers/gpu/drm/bridge/tc358775.c +4 -12
@@ -528,25 +528,17 @@ tc_mode_valid(struct drm_bridge *bridge,static int tc358775_parse_dt (struct device_node *np,struct tc_data *tc) {struct device_node *endpoint; -struct device_node *parent;struct device_node *remote;int dsi_lanes =-1 ; -/* -* To get the data-lanes of dsi, we need to access the dsi0_out of port1 -* of dsi0 endpoint from bridge port0 of d2l_in -*/ endpoint =of_graph_get_endpoint_by_regs (tc->dev->of_node,TC358775_DSI_IN ,-1 );if (endpoint) { -/* dsi0_out node */ - parent =of_graph_get_remote_port_parent (endpoint); +/* Get the configured data lanes on the dsi host side */ + remote =of_graph_get_remote_endpoint (endpoint);of_node_put (endpoint); -if (parent) { -/* dsi0 port 1 */ - dsi_lanes =drm_of_get_data_lanes_count_ep (parent,1 ,-1 ,1 ,4 ); -of_node_put (parent); - } + dsi_lanes =drm_of_get_data_lanes_count (remote,1 ,4 ); +of_node_put (remote); }if (dsi_lanes <0 )
Signature · 1 line
2.42.1
PATCH 3/6 drm/bridge: tc358775: Add jeida-24 support
The jeida-24 register values are the default hardware settings, but they not listed in the driver. Let's add them.
--- drivers/gpu/drm/bridge/tc358775.c | 21 ++++++++++++++++++--- 1 file changed, 18 insertions(+), 3 deletions(-)
drivers/gpu/drm/bridge/tc358775.c +18 -3
@@ -458,8 +458,18 @@ static void tc_bridge_enable(struct drm_bridge *bridge)* Default hardware register settings of tc358775 configured * with MEDIA_BUS_FMT_RGB888_1X7X4_JEIDA jeida-24 format */ -if (connector->display_info.bus_formats[0 ] == -MEDIA_BUS_FMT_RGB888_1X7X4_SPWG ) { +switch (connector->display_info.bus_formats[0 ]) { +case MEDIA_BUS_FMT_RGB888_1X7X4_JEIDA : +/* JEIDA-24 */ +d2l_write (tc->i2c,LV_MX0003 ,LV_MX (LVI_R2 ,LVI_R3 ,LVI_R4 ,LVI_R5 )); +d2l_write (tc->i2c,LV_MX0407 ,LV_MX (LVI_R6 ,LVI_R1 ,LVI_R7 ,LVI_G2 )); +d2l_write (tc->i2c,LV_MX0811 ,LV_MX (LVI_G3 ,LVI_G4 ,LVI_G0 ,LVI_G1 )); +d2l_write (tc->i2c,LV_MX1215 ,LV_MX (LVI_G5 ,LVI_G6 ,LVI_G7 ,LVI_B2 )); +d2l_write (tc->i2c,LV_MX1619 ,LV_MX (LVI_B0 ,LVI_B1 ,LVI_B3 ,LVI_B4 )); +d2l_write (tc->i2c,LV_MX2023 ,LV_MX (LVI_B5 ,LVI_B6 ,LVI_B7 ,LVI_L0 )); +d2l_write (tc->i2c,LV_MX2427 ,LV_MX (LVI_HS ,LVI_VS ,LVI_DE ,LVI_R0 )); +break ; +case MEDIA_BUS_FMT_RGB888_1X7X4_SPWG :/* VESA-24 */ d2l_write (tc->i2c,LV_MX0003 ,LV_MX (LVI_R0 ,LVI_R1 ,LVI_R2 ,LVI_R3 ));d2l_write (tc->i2c,LV_MX0407 ,LV_MX (LVI_R4 ,LVI_R7 ,LVI_R5 ,LVI_G0 ));
@@ -468,7 +478,9 @@ static void tc_bridge_enable(struct drm_bridge *bridge)d2l_write (tc->i2c,LV_MX1619 ,LV_MX (LVI_B6 ,LVI_B7 ,LVI_B1 ,LVI_B2 ));d2l_write (tc->i2c,LV_MX2023 ,LV_MX (LVI_B3 ,LVI_B4 ,LVI_B5 ,LVI_L0 ));d2l_write (tc->i2c,LV_MX2427 ,LV_MX (LVI_HS ,LVI_VS ,LVI_DE ,LVI_R6 )); - }else {/* MEDIA_BUS_FMT_RGB666_1X7X3_SPWG - JEIDA-18 */ +break ; +case MEDIA_BUS_FMT_RGB666_1X7X3_SPWG : +/* JEIDA-18 */ d2l_write (tc->i2c,LV_MX0003 ,LV_MX (LVI_R0 ,LVI_R1 ,LVI_R2 ,LVI_R3 ));d2l_write (tc->i2c,LV_MX0407 ,LV_MX (LVI_R4 ,LVI_L0 ,LVI_R5 ,LVI_G0 ));d2l_write (tc->i2c,LV_MX0811 ,LV_MX (LVI_G1 ,LVI_G2 ,LVI_L0 ,LVI_L0 ));
@@ -476,6 +488,9 @@ static void tc_bridge_enable(struct drm_bridge *bridge)d2l_write (tc->i2c,LV_MX1619 ,LV_MX (LVI_L0 ,LVI_L0 ,LVI_B1 ,LVI_B2 ));d2l_write (tc->i2c,LV_MX2023 ,LV_MX (LVI_B3 ,LVI_B4 ,LVI_B5 ,LVI_L0 ));d2l_write (tc->i2c,LV_MX2427 ,LV_MX (LVI_HS ,LVI_VS ,LVI_DE ,LVI_L0 )); +break ; +default : +break ; }d2l_write (tc->i2c,VFUEN ,VFUEN_EN );
Signature · 1 line
2.42.1
PATCH 4/6 drm/bridge: tc358775: Add burst and low-power modes
Burst and low-power modes are supported both for tc358765 and tc358775.
--- drivers/gpu/drm/bridge/tc358775.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/gpu/drm/bridge/tc358775.c +2 -1
@@ -632,7 +632,8 @@ static int tc_attach_host(struct tc_data *tc) dsi->lanes = tc->num_dsi_lanes; dsi->format =MIPI_DSI_FMT_RGB888 ; - dsi->mode_flags =MIPI_DSI_MODE_VIDEO ; + dsi->mode_flags =MIPI_DSI_MODE_VIDEO |MIPI_DSI_MODE_VIDEO_BURST | +MIPI_DSI_MODE_LPM ; ret =devm_mipi_dsi_attach (dev, dsi);if (ret <0 ) {
Signature · 1 line
2.42.1
PATCH 5/6 drm/bridge: tc358775: Add support for tc358765
Looks like tc358775 is pin compatible with earlier tc358765 according to the tc358774xbg_datasheet_en_20190118.pdf documentation. On tc358775, there is an extra GPIO for STBY pin added, and few other improvments.
The tc358765 has a register bit for video event mode that we must set for the LCD output to work. On tc358775, this bit no longer exists.
Looks like the registers seem to match otherwise based on a quick glance comparing the defines to the earlier Android kernel tc358765 driver.
--- drivers/gpu/drm/bridge/tc358775.c | 55 +++++++++++++++++++++++-------- 1 file changed, 42 insertions(+), 13 deletions(-)
drivers/gpu/drm/bridge/tc358775.c +42 -13
@@ -15,6 +15,7 @@#include <linux/kernel.h> #include <linux/media-bus-format.h> #include <linux/module.h> +#include <linux/of_device.h> #include <linux/regulator/consumer.h> #include <linux/slab.h>
@@ -107,6 +108,7 @@#define RDPKTLN 0x0404/* Command Read Packet Length */ #define VPCTRL 0x0450/* Video Path Control */ +#define EVTMODE BIT(5)/* Video event mode enable, tc35876x only */ #define HTIM1 0x0454/* Horizontal Timing Control 1 */ #define HTIM2 0x0458/* Horizontal Timing Control 2 */ #define VTIM1 0x045C/* Vertical Timing Control 1 */
@@ -254,6 +256,11 @@ enum tc358775_ports { TC358775_LVDS_OUT1, }; +enum tc3587x5_type { +TC358765 , +TC358775 , +}; +struct tc_data {struct i2c_client *i2c;struct device *dev;
@@ -271,6 +278,8 @@ struct tc_data {struct gpio_desc *stby_gpio;u8 lvds_link;/* single-link or dual-link */ u8 bpc; + +enum tc3587x5_type type; };static inline struct tc_data *bridge_to_tc (struct drm_bridge *b)
@@ -294,8 +303,10 @@ static void tc_bridge_pre_enable(struct drm_bridge *bridge)dev_err (dev,"regulator vdd enable failed, %d\n" , ret);usleep_range (10000 ,11000 ); -gpiod_set_value (tc->stby_gpio,0 ); -usleep_range (10000 ,11000 ); +if (!IS_ERR (tc->stby_gpio)) { +gpiod_set_value (tc->stby_gpio,0 ); +usleep_range (10000 ,11000 ); + }gpiod_set_value (tc->reset_gpio,0 );usleep_range (10 ,20 );
@@ -310,8 +321,10 @@ static void tc_bridge_post_disable(struct drm_bridge *bridge)gpiod_set_value (tc->reset_gpio,1 );usleep_range (10 ,20 ); -gpiod_set_value (tc->stby_gpio,1 ); -usleep_range (10000 ,11000 ); +if (!IS_ERR (tc->stby_gpio)) { +gpiod_set_value (tc->stby_gpio,1 ); +usleep_range (10000 ,11000 ); + } ret =regulator_disable (tc->vdd);if (ret <0 )
@@ -424,10 +437,16 @@ static void tc_bridge_enable(struct drm_bridge *bridge)d2l_write (tc->i2c,PPI_STARTPPI ,PPI_START_FUNCTION );d2l_write (tc->i2c,DSI_STARTDSI ,DSI_RX_START ); +/* Video event mode, this bit does not exist for tc358775 */ +if (tc->type ==TC358765 ) + val =EVTMODE ; +else + val =0 ; +if (tc->bpc ==8 ) - val =TC358775_VPCTRL_OPXLFMT (1 ); + val |=TC358775_VPCTRL_OPXLFMT (1 );else /* bpc = 6; */ - val =TC358775_VPCTRL_MSF (1 ); + val |=TC358775_VPCTRL_MSF (1 ); dsiclk = mode->crtc_clock *3 * tc->bpc / tc->num_dsi_lanes /1000 ; clkdiv = dsiclk / (tc->lvds_link ==DUAL_LINK ?DIVIDE_BY_6 :DIVIDE_BY_3 );
@@ -656,6 +675,7 @@ static int tc_probe(struct i2c_client *client) tc->dev = dev; tc->i2c = client; + tc->type = (enum tc3587x5_type )of_device_get_match_data (dev); tc->panel_bridge =devm_drm_of_get_bridge (dev, dev->of_node,TC358775_LVDS_OUT0 ,0 );
@@ -680,11 +700,15 @@ static int tc_probe(struct i2c_client *client)return ret; } - tc->stby_gpio =devm_gpiod_get (dev,"stby" ,GPIOD_OUT_HIGH ); -if (IS_ERR (tc->stby_gpio)) { - ret =PTR_ERR (tc->stby_gpio); -dev_err (dev,"cannot get stby-gpio %d\n" , ret); -return ret; +if (tc->type ==TC358775 ) { + tc->stby_gpio =devm_gpiod_get (dev,"stby" ,GPIOD_OUT_HIGH ); +if (IS_ERR (tc->stby_gpio)) { + ret =PTR_ERR (tc->stby_gpio); +dev_err (dev,"cannot get stby-gpio %d\n" , ret); +return ret; + } + }else { + tc->stby_gpio =ERR_PTR (-ENODEV ); } tc->reset_gpio =devm_gpiod_get (dev,"reset" ,GPIOD_OUT_HIGH );
@@ -696,6 +720,7 @@ static int tc_probe(struct i2c_client *client) tc->bridge.funcs = &tc_bridge_funcs; tc->bridge.of_node = dev->of_node; + tc->bridge.pre_enable_prev_first = true;drm_bridge_add (&tc->bridge);i2c_set_clientdata (client, tc);
@@ -715,17 +740,21 @@ static void tc_remove(struct i2c_client *client) {struct tc_data *tc =i2c_get_clientdata (client); +mipi_dsi_detach (tc->dsi);drm_bridge_remove (&tc->bridge); + tc->bridge.funcs =NULL ; }static const struct i2c_device_id tc358775_i2c_ids[] = { - {"tc358775" ,0 }, + {"tc358765" ,TC358765 , }, + {"tc358775" ,TC358775 , }, { } };MODULE_DEVICE_TABLE (i2c, tc358775_i2c_ids);static const struct of_device_id tc358775_of_ids[] = { - { .compatible ="toshiba,tc358775" , }, + { .compatible ="toshiba,tc358765" , .data = (void *)TC358765 , }, + { .compatible ="toshiba,tc358775" , .data = (void *)TC358775 , }, { } };MODULE_DEVICE_TABLE (of, tc358775_of_ids);
Signature · 1 line
2.42.1
PATCH 6/6 drm/bridge: tc358775: Configure hs_rate and lp_rate
The hs_rate and lp_rate may be used by the dsi host for timing calculations. The tc358775 has a maximum bit rate of 1 Gbps/lane, tc358765 has maximurate of 800 Mbps per lane.
--- drivers/gpu/drm/bridge/tc358775.c | 5 +++++ 1 file changed, 5 insertions(+)
drivers/gpu/drm/bridge/tc358775.c +5 -0
@@ -653,6 +653,11 @@ static int tc_attach_host(struct tc_data *tc) dsi->format =MIPI_DSI_FMT_RGB888 ; dsi->mode_flags =MIPI_DSI_MODE_VIDEO |MIPI_DSI_MODE_VIDEO_BURST |MIPI_DSI_MODE_LPM ; +if (tc->type ==TC358765 ) + dsi->hs_rate =800000000 ; +else + dsi->hs_rate =1000000000 ; + dsi->lp_rate =10000000 ; ret =devm_mipi_dsi_attach (dev, dsi);if (ret <0 ) {
Signature · 1 line
2.42.1
Re: [PATCH 3/6] drm/bridge: tc358775: Add jeida-24 support
In reply to Tony LindgrenQuoted 2 lines
The jeida-24 register values are the default hardware settings, but they not listed in the driver. Let's add them.
jeida-24 and jeida-18 should have the same mapping, jeida-18 is broken in this driver. could you test this patch:
--snip--
From 46da1d76d4908e5879ed746cce1faeacd69c432e Mon Sep 17 00:00:00 2001
From: Michael Walle <[email protected]>
Date: Wed, 4 Oct 2023 13:52:57 +0200
Subject: [PATCH] drm/bridge: tc358775: fix support for jeida-18 and jeida-24
The bridge always uses 24bpp internally. Therefore, for jeida-18 mapping we need to discard the lowest two bits for each channel and thus starting with LV_[RGB]2. jeida-24 has the same mapping but uses four lanes instead of three, with the forth pair transmitting the lowest two bits of each channel. Thus, the mapping between jeida-18 and jeida-24 is actually the same, except that one channel is turned off (by selecting the RGB666 format in VPCTRL).
While at it, remove the bogus comment about the hardware default because the default is overwritten in any case.
Tested with a jeida-18 display (Evervision VGG644804).
--- drivers/gpu/drm/bridge/tc358775.c | 21 +++++++++------------ 1 file changed, 9 insertions(+), 12 deletions(-)
drivers/gpu/drm/bridge/tc358775.c +9 -12
@@ -454,10 +454,6 @@ static void tc_bridge_enable(struct drm_bridge *bridge)dev_dbg (tc->dev,"bus_formats %04x bpc %d\n" , connector->display_info.bus_formats[0 ], tc->bpc); -/* -* Default hardware register settings of tc358775 configured -* with MEDIA_BUS_FMT_RGB888_1X7X4_JEIDA jeida-24 format -*/ if (connector->display_info.bus_formats[0 ] ==MEDIA_BUS_FMT_RGB888_1X7X4_SPWG ) {/* VESA-24 */
@@ -468,14 +464,15 @@ static void tc_bridge_enable(struct drm_bridge *bridge)d2l_write (tc->i2c,LV_MX1619 ,LV_MX (LVI_B6 ,LVI_B7 ,LVI_B1 ,LVI_B2 ));d2l_write (tc->i2c,LV_MX2023 ,LV_MX (LVI_B3 ,LVI_B4 ,LVI_B5 ,LVI_L0 ));d2l_write (tc->i2c,LV_MX2427 ,LV_MX (LVI_HS ,LVI_VS ,LVI_DE ,LVI_R6 )); - }else {/* MEDIA_BUS_FMT_RGB666_1X7X3_SPWG - JEIDA-18 */ -d2l_write (tc->i2c,LV_MX0003 ,LV_MX (LVI_R0 ,LVI_R1 ,LVI_R2 ,LVI_R3 )); -d2l_write (tc->i2c,LV_MX0407 ,LV_MX (LVI_R4 ,LVI_L0 ,LVI_R5 ,LVI_G0 )); -d2l_write (tc->i2c,LV_MX0811 ,LV_MX (LVI_G1 ,LVI_G2 ,LVI_L0 ,LVI_L0 )); -d2l_write (tc->i2c,LV_MX1215 ,LV_MX (LVI_G3 ,LVI_G4 ,LVI_G5 ,LVI_B0 )); -d2l_write (tc->i2c,LV_MX1619 ,LV_MX (LVI_L0 ,LVI_L0 ,LVI_B1 ,LVI_B2 )); -d2l_write (tc->i2c,LV_MX2023 ,LV_MX (LVI_B3 ,LVI_B4 ,LVI_B5 ,LVI_L0 )); -d2l_write (tc->i2c,LV_MX2427 ,LV_MX (LVI_HS ,LVI_VS ,LVI_DE ,LVI_L0 )); + }else { +/* JEIDA-18 and JEIDA-24 */ +d2l_write (tc->i2c,LV_MX0003 ,LV_MX (LVI_R2 ,LVI_R3 ,LVI_R4 ,LVI_R5 )); +d2l_write (tc->i2c,LV_MX0407 ,LV_MX (LVI_R6 ,LVI_R1 ,LVI_R7 ,LVI_G2 )); +d2l_write (tc->i2c,LV_MX0811 ,LV_MX (LVI_G3 ,LVI_G4 ,LVI_G0 ,LVI_G1 )); +d2l_write (tc->i2c,LV_MX1215 ,LV_MX (LVI_G5 ,LVI_G6 ,LVI_G7 ,LVI_B2 )); +d2l_write (tc->i2c,LV_MX1619 ,LV_MX (LVI_B0 ,LVI_B1 ,LVI_B3 ,LVI_B4 )); +d2l_write (tc->i2c,LV_MX2023 ,LV_MX (LVI_B5 ,LVI_B6 ,LVI_B7 ,LVI_L0 )); +d2l_write (tc->i2c,LV_MX2427 ,LV_MX (LVI_HS ,LVI_VS ,LVI_DE ,LVI_R0 )); }d2l_write (tc->i2c,VFUEN ,VFUEN_EN );
Signature · 1 line
2.39.2
Tony Lindgren
Tested-byRe: [PATCH 3/6] drm/bridge: tc358775: Add jeida-24 support
Quoted 5 lines · Michael Walle
Quoted 2 lines
The jeida-24 register values are the default hardware settings, but they not listed in the driver. Let's add them.
jeida-24 and jeida-18 should have the same mapping, jeida-18 is broken in this driver. could you test this patch:
Yes great works for me with the tc358765 patches:
Quoted 68 lines
--snip--
From
46da1d76d4908e5879ed746cce1faeacd69c432eMon Sep 17 00:00:00 2001
From: Michael Walle <[email protected]>
Date: Wed, 4 Oct 2023 13:52:57 +0200
Subject: [PATCH] drm/bridge: tc358775: fix support for jeida-18 and jeida-24The bridge always uses 24bpp internally. Therefore, for jeida-18 mapping we need to discard the lowest two bits for each channel and thus starting with LV_[RGB]2. jeida-24 has the same mapping but uses four lanes instead of three, with the forth pair transmitting the lowest two bits of each channel. Thus, the mapping between jeida-18 and jeida-24 is actually the same, except that one channel is turned off (by selecting the RGB666 format in VPCTRL).
While at it, remove the bogus comment about the hardware default because the default is overwritten in any case.
Tested with a jeida-18 display (Evervision VGG644804).
Fixes b26975593b17 ("display/drm/bridge: TC358775 DSI/LVDS driver")Signed-off-by Michael Walle <[email protected]>--- drivers/gpu/drm/bridge/tc358775.c | 21 +++++++++------------ 1 file changed, 9 insertions(+), 12 deletions(-)drivers/gpu/drm/bridge/tc358775.c +9
-12@@ -454,10 +454,6 @@ static void tc_bridge_enable(struct drm_bridge *bridge)dev_dbg (tc->dev,"bus_formats %04x bpc %d\n" , connector->display_info.bus_formats[0 ], tc->bpc); -/* -* Default hardware register settings of tc358775 configured -* with MEDIA_BUS_FMT_RGB888_1X7X4_JEIDA jeida-24 format -*/ if (connector->display_info.bus_formats[0 ] ==MEDIA_BUS_FMT_RGB888_1X7X4_SPWG ) {/* VESA-24 */ @@ -468,14 +464,15 @@ static void tc_bridge_enable(struct drm_bridge *bridge)d2l_write (tc->i2c,LV_MX1619 ,LV_MX (LVI_B6 ,LVI_B7 ,LVI_B1 ,LVI_B2 ));d2l_write (tc->i2c,LV_MX2023 ,LV_MX (LVI_B3 ,LVI_B4 ,LVI_B5 ,LVI_L0 ));d2l_write (tc->i2c,LV_MX2427 ,LV_MX (LVI_HS ,LVI_VS ,LVI_DE ,LVI_R6 )); - }else {/* MEDIA_BUS_FMT_RGB666_1X7X3_SPWG - JEIDA-18 */ -d2l_write (tc->i2c,LV_MX0003 ,LV_MX (LVI_R0 ,LVI_R1 ,LVI_R2 ,LVI_R3 )); -d2l_write (tc->i2c,LV_MX0407 ,LV_MX (LVI_R4 ,LVI_L0 ,LVI_R5 ,LVI_G0 )); -d2l_write (tc->i2c,LV_MX0811 ,LV_MX (LVI_G1 ,LVI_G2 ,LVI_L0 ,LVI_L0 )); -d2l_write (tc->i2c,LV_MX1215 ,LV_MX (LVI_G3 ,LVI_G4 ,LVI_G5 ,LVI_B0 )); -d2l_write (tc->i2c,LV_MX1619 ,LV_MX (LVI_L0 ,LVI_L0 ,LVI_B1 ,LVI_B2 )); -d2l_write (tc->i2c,LV_MX2023 ,LV_MX (LVI_B3 ,LVI_B4 ,LVI_B5 ,LVI_L0 )); -d2l_write (tc->i2c,LV_MX2427 ,LV_MX (LVI_HS ,LVI_VS ,LVI_DE ,LVI_L0 )); + }else { +/* JEIDA-18 and JEIDA-24 */ +d2l_write (tc->i2c,LV_MX0003 ,LV_MX (LVI_R2 ,LVI_R3 ,LVI_R4 ,LVI_R5 )); +d2l_write (tc->i2c,LV_MX0407 ,LV_MX (LVI_R6 ,LVI_R1 ,LVI_R7 ,LVI_G2 )); +d2l_write (tc->i2c,LV_MX0811 ,LV_MX (LVI_G3 ,LVI_G4 ,LVI_G0 ,LVI_G1 )); +d2l_write (tc->i2c,LV_MX1215 ,LV_MX (LVI_G5 ,LVI_G6 ,LVI_G7 ,LVI_B2 )); +d2l_write (tc->i2c,LV_MX1619 ,LV_MX (LVI_B0 ,LVI_B1 ,LVI_B3 ,LVI_B4 )); +d2l_write (tc->i2c,LV_MX2023 ,LV_MX (LVI_B5 ,LVI_B6 ,LVI_B7 ,LVI_L0 )); +d2l_write (tc->i2c,LV_MX2427 ,LV_MX (LVI_HS ,LVI_VS ,LVI_DE ,LVI_R0 )); }d2l_write (tc->i2c,VFUEN ,VFUEN_EN );Signature · 1 line
2.39.2
Re: [PATCH 2/6] drm/bridge: tc358775: Fix getting dsi host data lanes
In reply to Tony LindgrenQuoted 30 lines
The current code assume hardcoded dsi host endpoint 1, which may not be the case. Let's fix that and simplify the code by getting the dsi endpoint with
of_graph_get_remote_endpoint()that does not assume any endpoint numbering.Fixes b26975593b17 ("display/drm/bridge: TC358775 DSI/LVDS driver")Signed-off-by Tony Lindgren <[email protected]>--- drivers/gpu/drm/bridge/tc358775.c | 16 ++++------------ 1 file changed, 4 insertions(+), 12 deletions(-)drivers/gpu/drm/bridge/tc358775.c +0
-6@@ -528,25 +528,17 @@ tc_mode_valid(struct drm_bridge *bridge,static int tc358775_parse_dt (struct device_node *np,struct tc_data *tc) {struct device_node *endpoint; -struct device_node *parent;struct device_node *remote;int dsi_lanes =-1 ; -/* -* To get the data-lanes of dsi, we need to access the dsi0_out of port1 -* of dsi0 endpoint from bridge port0 of d2l_in -*/ endpoint =of_graph_get_endpoint_by_regs (tc->dev->of_node,TC358775_DSI_IN ,-1 );if (endpoint) { -/* dsi0_out node */
drivers/gpu/drm/bridge/tc358775.c tc_mode_valid(struct drm_bridge *bridge, · line 540
Quoted 10 lines
drivers/gpu/drm/bridge/tc358775.c +3
-6- parent =of_graph_get_remote_port_parent (endpoint); +/* Get the configured data lanes on the dsi host side */ + remote =of_graph_get_remote_endpoint (endpoint);of_node_put (endpoint); -if (parent) { -/* dsi0 port 1 */ - dsi_lanes =drm_of_get_data_lanes_count_ep (parent,1 ,-1 ,1 ,4 ); -of_node_put (parent); - } + dsi_lanes =drm_of_get_data_lanes_count (remote,1 ,4 );
I actually have the same fix, but with one additional detail, which I'm unsure about though: This looks at the data-lanes property of the *remote* endpoint whereas other bridge drivers (see tc358767, ti-sn65dsi83, lt8912b, anx7625) look at the local endpoint and I'm not sure what is correct.
-michael
Re: [PATCH 2/6] drm/bridge: tc358775: Fix getting dsi host data lanes
Quoted 4 lines · Michael Walle
I actually have the same fix, but with one additional detail, which I'm unsure about though: This looks at the data-lanes property of the *remote* endpoint whereas other bridge drivers (see tc358767, ti-sn65dsi83, lt8912b, anx7625) look at the local endpoint and I'm not sure what is correct.
Yes I've been wondering about that too. Let's just move it over to the bridge node? We could produce a warning if the dsi host node has the data-lanes property.. No current in kernel users AFAIK.
FYI, for omapdrm, we already have a legacy dt property "lanes" for the wiring that tells number of lanes used and the order of the lanes.
Regards,
Tony
Re: [PATCH 2/6] drm/bridge: tc358775: Fix getting dsi host data lanes
+ dt maintainers
Quoted 8 lines
Quoted 4 lines
I actually have the same fix, but with one additional detail, which I'm unsure about though: This looks at the data-lanes property of the *remote* endpoint whereas other bridge drivers (see tc358767, ti-sn65dsi83, lt8912b, anx7625) look at the local endpoint and I'm not sure what is correct.
Yes I've been wondering about that too. Let's just move it over to the bridge node? We could produce a warning if the dsi host node has the data-lanes property.. No current in kernel users AFAIK.
I haven't found any in-tree users either. In my patch, I first try the remote end and then the local end. But thinking more about it I don't think this is correct. Maybe we can do it the other way around, first try data-lanes of the local endpoint and if not found, then try the remote one. That way, we would at least be backwards compatible in the driver. And for the dt-bindings, make it mandatory to have a local data-lanes.
-michael
Quoted 6 lines
FYI, for omapdrm, we already have a legacy dt property "lanes" for the wiring that tells number of lanes used and the order of the lanes.
Regards,
Tony
Re: [PATCH 2/6] drm/bridge: tc358775: Fix getting dsi host data lanes
Quoted 14 lines · Michael Walle
+ dt maintainers
Quoted 11 lines
Quoted 7 lines
I actually have the same fix, but with one additional detail, which I'm
unsure about though: This looks at the data-lanes property of the *remote*
endpoint whereas other bridge drivers (see tc358767, ti-sn65dsi83, lt8912b,
anx7625) look at the local endpoint and I'm not sure what is correct.Yes I've been wondering about that too. Let's just move it over to the bridge node? We could produce a warning if the dsi host node has the data-lanes property.. No current in kernel users AFAIK.
Quoted 7 lines
I haven't found any in-tree users either. In my patch, I first try the remote
end and then the local end. But thinking more about it I don't think this is correct. Maybe we can do it the other way around, first try data-lanes of the local endpoint and if not found, then try the remote one. That way, we would at least be backwards compatible in the driver. And for the dt-bindings, make it mandatory to have a local data-lanes.
OK sounds good to me.
Tony
Quoted 2 lines · Tony Lindgren
The tc358765 is similar to tc358775 except for the stdby-gpios.
Best regards,
Krzysztof
Hi,
Quoted 1 line
The tc358765 is similar to tc358775 except for the stdby-gpios.
Bad timing (for me). I'm about to send a bigger patch series for the tc358775 which fixes the (completely) broken initialialization. And also contains some of your fixes.
That being said, I intend to make the standby gpio optional also for the tc358755, because it might just be hardwired on the board.
But second, I'm really curious if this bridge is working for you correctly as it is at the moment. One particular thing I've noticed is that you must release the reset while both the clock and the data lanes are in LP11 mode. Otherwise, the bridge won't work properly (i.e. horizontally shifted picture, or no picture at all).
What DSI host controller are you using?
-michael
Quoted 7 lines · Michael Walle
Hi,
Quoted 1 line
The tc358765 is similar to tc358775 except for the stdby-gpios.
Bad timing (for me). I'm about to send a bigger patch series for the tc358775 which fixes the (completely) broken initialialization. And also contains some of your fixes.
OK cool, let's merge patches as needed then. Maybe ack the patches that can already be merged, and put together some merged set for the rest of the patches? Or let me know what you prefer, I'll be glad to test and tweak as needed for tc358765.
Quoted 2 lines
That being said, I intend to make the standby gpio optional also for the tc358755, because it might just be hardwired on the board.
OK that sounds good to me.
Quoted 5 lines
But second, I'm really curious if this bridge is working for you correctly as it is at the moment. One particular thing I've noticed is that you must release the reset while both the clock and the data lanes are in LP11 mode. Otherwise, the bridge won't work properly (i.e. horizontally shifted picture, or no picture at all).
Yes things are working for me. But then again the bridge is initialized by the bootloader, and then Android kernel, and then I kexec to the mainline kernel. And this is with a tc358765 if that might make a difference.
So I have not seen your reset issue. Andreas may be seeing it on another tc bridge variant though, so adding Andreas to the loop also.
Quoted 1 line
What DSI host controller are you using?
This is an old motorola mz617 tablet with a tc358765 bridge, so omapdrm. I do have one pending patch for omapdrm dsi to change the init order a bit so tc358765 probes reliably. But seems that's a separate issue from your reset issue, I'll post that to the lists too to discuss.
What's the dsi host you have? Do you also have some separate i2c eeprom that's needed for initializing something or is that lcd panel specific? No idea what the eeprom is really doing here..
Regards,
Tony
Hi,
Am Montag, 27. November 2023, 13:44:30 CET schrieb Michael Walle:
Quoted 8 lines
Hi,
Quoted 1 line
The tc358765 is similar to tc358775 except for the stdby-gpios.
Bad timing (for me). I'm about to send a bigger patch series for the tc358775 which fixes the (completely) broken initialialization. And also contains some of your fixes.
Quoted 8 lines
That being said, I intend to make the standby gpio optional also for the tc358755, because it might just be hardwired on the board.
But second, I'm really curious if this bridge is working for you correctly as it is at the moment. One particular thing I've noticed is that you must release the reset while both the clock and the data lanes are in LP11 mode. Otherwise, the bridge won't work properly (i.e. horizontally shifted picture, or no picture at all).
Apparently this seems to be true for all Toshiba DSI bridges. The power on sequence for TC9595 (TC358767) also requires LP-11 before releasing the reset signal RESX. Additionally LP-11 is requires for using the DP AUX channel. This also relates to the patch set from Dmitry [1].
Best regards,
Alexander
[1] https://lore.kernel.org/dri-devel/[email protected]/
Quoted 3 lines
What DSI host controller are you using?
-michael
Signature · 4 lines
TQ-Systems GmbH | Mühlstraße 2, Gut Delling | 82229 Seefeld, Germany Amtsgericht München, HRB 105018 Geschäftsführer: Detlef Schneider, Rüdiger Stahl, Stefan Schneider http://www.tq-group.com/