thermal: k3_j72xx_bandgap: implement suspend/resume support
PATCH v2 1/1 thermal: k3_j72xx_bandgap: implement suspend/resume support
From: Théo Lebrun <[email protected]>
This add suspend-to-ram support.
The derived_table is kept-as is, so the resume is only about pm_runtime_* calls and restoring the same registers as the probe.
Extract the hardware initialization procedure to a function called at both probe-time & resume-time.
The probe-time loop is split in two to ensure doing the hardware initialization before registering thermal zones. That ensures our callbacks cannot be called while in bad state.
---
v2:
- Fix warnings/errors reported by kernel test robot
drivers/thermal/k3_j72xx_bandgap.c | 112 ++++++++++++++++++++--------- 1 file changed, 79 insertions(+), 33 deletions(-)
drivers/thermal/k3_j72xx_bandgap.c +79 -33
@@ -178,6 +178,7 @@ struct k3_j72xx_bandgap {void __iomem *base;void __iomem *cfg2_base;struct k3_thermal_data *ts_data[K3_VTM_MAX_NUM_TS ]; +int cnt; };/* common data structures */
@@ -338,24 +339,53 @@ static void print_look_up_table(struct device *dev, int *ref_table)dev_dbg (dev,"%d %d %d\n" , i, derived_table[i], ref_table[i]); } +static void k3_j72xx_bandgap_init_hw (struct k3_j72xx_bandgap *bgp) +{ +struct k3_thermal_data *data; +int id, high_max, low_temp; +u32 val; + +for (id =0 ; id < bgp->cnt; id++) { + data = bgp->ts_data[id]; + val =readl (bgp->cfg2_base + data->ctrl_offset); + val |= (K3_VTM_TMPSENS_CTRL_MAXT_OUTRG_EN | +K3_VTM_TMPSENS_CTRL_SOC | +K3_VTM_TMPSENS_CTRL_CLRZ |BIT (4 )); +writel (val, bgp->cfg2_base + data->ctrl_offset); + } + +/* +* Program TSHUT thresholds +* Step 1: set the thresholds to ~123C and 105C WKUP_VTM_MISC_CTRL2 +* Step 2: WKUP_VTM_TMPSENS_CTRL_j set the MAXT_OUTRG_EN bit +* This is already taken care as per of init +* Step 3: WKUP_VTM_MISC_CTRL set the ANYMAXT_OUTRG_ALERT_EN bit +*/ + high_max =k3_j72xx_bandgap_temp_to_adc_code (MAX_TEMP ); + low_temp =k3_j72xx_bandgap_temp_to_adc_code (COOL_DOWN_TEMP ); + +writel ((low_temp <<16 ) | high_max, bgp->cfg2_base +K3_VTM_MISC_CTRL2_OFFSET ); +mdelay (100 ); +writel (K3_VTM_ANYMAXT_OUTRG_ALERT_EN , bgp->cfg2_base +K3_VTM_MISC_CTRL_OFFSET ); +} +struct k3_j72xx_bandgap_data {const bool has_errata_i2128; };static int k3_j72xx_bandgap_probe (struct platform_device *pdev) { -int ret =0 , cnt, val, id; -int high_max, low_temp; -struct resource *res; +const struct k3_j72xx_bandgap_data *driver_data; +struct thermal_zone_device *ti_thermal;struct device *dev = &pdev->dev; +bool workaround_needed = false;struct k3_j72xx_bandgap *bgp;struct k3_thermal_data *data; -bool workaround_needed = false; -const struct k3_j72xx_bandgap_data *driver_data; -struct thermal_zone_device *ti_thermal; -int *ref_table;struct err_values err_vals;void __iomem *fuse_base; +int ret =0 , val, id; +struct resource *res; +int *ref_table;const s64 golden_factors[] = {-490019999999999936 ,
@@ -422,10 +452,10 @@ static int k3_j72xx_bandgap_probe(struct platform_device *pdev)/* Get the sensor count in the VTM */ val =readl (bgp->base +K3_VTM_DEVINFO_PWR0_OFFSET ); - cnt = val &K3_VTM_DEVINFO_PWR0_TEMPSENS_CT_MASK ; - cnt >>=__ffs (K3_VTM_DEVINFO_PWR0_TEMPSENS_CT_MASK ); + bgp->cnt = val &K3_VTM_DEVINFO_PWR0_TEMPSENS_CT_MASK ; + bgp->cnt >>=__ffs (K3_VTM_DEVINFO_PWR0_TEMPSENS_CT_MASK ); - data =devm_kcalloc (bgp->dev, cnt,sizeof (*data),GFP_KERNEL ); + data =devm_kcalloc (bgp->dev, bgp->cnt,sizeof (*data),GFP_KERNEL );if (!data) { ret = -ENOMEM ; goto err_alloc;
@@ -449,8 +479,8 @@ static int k3_j72xx_bandgap_probe(struct platform_device *pdev)else init_table (3 , ref_table, pvt_wa_factors); -/* Register the thermal sensors */ -for (id =0 ; id < cnt; id++) { +/* Precompute the derived table & fill each thermal sensor struct */ +for (id =0 ; id < bgp->cnt; id++) { data[id].bgp = bgp; data[id].ctrl_offset =K3_VTM_TMPSENS0_CTRL_OFFSET + id *0x20 ; data[id].stat_offset = data[id].ctrl_offset +
@@ -470,13 +500,13 @@ static int k3_j72xx_bandgap_probe(struct platform_device *pdev)else if (id ==0 && !workaround_needed)memcpy (derived_table, ref_table,TABLE_SIZE *4 ); - val =readl (data[id].bgp->cfg2_base + data[id].ctrl_offset); - val |= (K3_VTM_TMPSENS_CTRL_MAXT_OUTRG_EN | -K3_VTM_TMPSENS_CTRL_SOC | -K3_VTM_TMPSENS_CTRL_CLRZ |BIT (4 )); -writel (val, data[id].bgp->cfg2_base + data[id].ctrl_offset); - bgp->ts_data[id] = &data[id]; + } + +k3_j72xx_bandgap_init_hw (bgp); + +/* Register the thermal sensors */ +for (id =0 ; id < bgp->cnt; id++) { ti_thermal =devm_thermal_of_zone_register (bgp->dev, id, &data[id], &k3_of_thermal_ops);if (IS_ERR (ti_thermal)) {
@@ -486,21 +516,7 @@ static int k3_j72xx_bandgap_probe(struct platform_device *pdev) } } -/* -* Program TSHUT thresholds -* Step 1: set the thresholds to ~123C and 105C WKUP_VTM_MISC_CTRL2 -* Step 2: WKUP_VTM_TMPSENS_CTRL_j set the MAXT_OUTRG_EN bit -* This is already taken care as per of init -* Step 3: WKUP_VTM_MISC_CTRL set the ANYMAXT_OUTRG_ALERT_EN bit -*/ - high_max =k3_j72xx_bandgap_temp_to_adc_code (MAX_TEMP ); - low_temp =k3_j72xx_bandgap_temp_to_adc_code (COOL_DOWN_TEMP ); - -writel ((low_temp <<16 ) | high_max, data[0 ].bgp->cfg2_base + -K3_VTM_MISC_CTRL2_OFFSET ); -mdelay (100 ); -writel (K3_VTM_ANYMAXT_OUTRG_ALERT_EN , data[0 ].bgp->cfg2_base + -K3_VTM_MISC_CTRL_OFFSET ); +platform_set_drvdata (pdev, bgp);print_look_up_table (dev, ref_table);/*
@@ -527,6 +543,35 @@ static void k3_j72xx_bandgap_remove(struct platform_device *pdev)pm_runtime_disable (&pdev->dev); } +static int __maybe_unused k3_j72xx_bandgap_suspend (struct device *dev) +{ +pm_runtime_put_sync (dev); +pm_runtime_disable (dev); +return 0 ; +} + +static int __maybe_unused k3_j72xx_bandgap_resume (struct device *dev) +{ +struct k3_j72xx_bandgap *bgp =dev_get_drvdata (dev); +int ret; + +pm_runtime_enable (dev); + ret =pm_runtime_get_sync (dev); +if (ret <0 ) { +pm_runtime_put_noidle (dev); +pm_runtime_disable (dev); +return ret; + } + +k3_j72xx_bandgap_init_hw (bgp); + +return 0 ; +} + +static const struct dev_pm_ops k3_j72xx_bandgap_pm_ops = { +SET_SYSTEM_SLEEP_PM_OPS (k3_j72xx_bandgap_suspend, k3_j72xx_bandgap_resume) +}; +static const struct k3_j72xx_bandgap_data k3_j72xx_bandgap_j721e_data = { .has_errata_i2128 = true, };
@@ -554,6 +599,7 @@ static struct platform_driver k3_j72xx_bandgap_sensor_driver = { .driver = { .name = "k3-j72xx-soc-thermal", .of_match_table = of_k3_j72xx_bandgap_match, + .pm = &k3_j72xx_bandgap_pm_ops, }, };
Signature · 1 line
2.39.2
Quoted 3 lines · Thomas Richard
From: Théo Lebrun <[email protected]>
This add suspend-to-ram support.
Hello,
Could someone please take a look at this patch ?
Regards,
Thomas
Quoted 8 lines · Thomas Richard
Quoted 3 lines · Thomas Richard
From: Théo Lebrun <[email protected]>
This add suspend-to-ram support.
Hello,
Could someone please take a look at this patch ?
Seems like the MAINTAINER file not up to date regarding ti_bandgap.c and ti_j*bandgap.c
[Added Keerthy]
Signature · 5 lines
<http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook | <http://twitter.com/#!/linaroorg> Twitter | <http://www.linaro.org/linaro-blog/> Blog
Added Keerthy
Quoted 209 lines · Thomas Richard
From: Théo Lebrun <[email protected]>
This add suspend-to-ram support.
The
derived_tableis kept-as is, so the resume is only about pm_runtime_* calls and restoring the same registers as the probe.Extract the hardware initialization procedure to a function called at both probe-time & resume-time.
The probe-time loop is split in two to ensure doing the hardware initialization before registering thermal zones. That ensures our callbacks cannot be called while in bad state.
Signed-off-by Théo Lebrun <[email protected]>Signed-off-by Thomas Richard <[email protected]>---
v2:
- Fix warnings/errors reported by kernel test robotdrivers/thermal/k3_j72xx_bandgap.c | 112 ++++++++++++++++++++--------- 1 file changed, 79 insertions(+), 33 deletions(-)drivers/thermal/k3_j72xx_bandgap.c +79
-33@@ -178,6 +178,7 @@ struct k3_j72xx_bandgap {void __iomem *base;void __iomem *cfg2_base;struct k3_thermal_data *ts_data[K3_VTM_MAX_NUM_TS ]; +int cnt; };/* common data structures */ @@ -338,24 +339,53 @@ static void print_look_up_table(struct device *dev, int *ref_table)dev_dbg (dev,"%d %d %d\n" , i, derived_table[i], ref_table[i]); } +static void k3_j72xx_bandgap_init_hw (struct k3_j72xx_bandgap *bgp) +{ +struct k3_thermal_data *data; +int id, high_max, low_temp; +u32 val; + +for (id =0 ; id < bgp->cnt; id++) { + data = bgp->ts_data[id]; + val =readl (bgp->cfg2_base + data->ctrl_offset); + val |= (K3_VTM_TMPSENS_CTRL_MAXT_OUTRG_EN | +K3_VTM_TMPSENS_CTRL_SOC | +K3_VTM_TMPSENS_CTRL_CLRZ |BIT (4 )); +writel (val, bgp->cfg2_base + data->ctrl_offset); + } + +/* +* Program TSHUT thresholds +* Step 1: set the thresholds to ~123C and 105C WKUP_VTM_MISC_CTRL2 +* Step 2: WKUP_VTM_TMPSENS_CTRL_j set the MAXT_OUTRG_EN bit +* This is already taken care as per of init +* Step 3: WKUP_VTM_MISC_CTRL set the ANYMAXT_OUTRG_ALERT_EN bit +*/ + high_max =k3_j72xx_bandgap_temp_to_adc_code (MAX_TEMP ); + low_temp =k3_j72xx_bandgap_temp_to_adc_code (COOL_DOWN_TEMP ); + +writel ((low_temp <<16 ) | high_max, bgp->cfg2_base +K3_VTM_MISC_CTRL2_OFFSET ); +mdelay (100 ); +writel (K3_VTM_ANYMAXT_OUTRG_ALERT_EN , bgp->cfg2_base +K3_VTM_MISC_CTRL_OFFSET ); +} +struct k3_j72xx_bandgap_data {const bool has_errata_i2128; };static int k3_j72xx_bandgap_probe (struct platform_device *pdev) { -int ret =0 , cnt, val, id; -int high_max, low_temp; -struct resource *res; +const struct k3_j72xx_bandgap_data *driver_data; +struct thermal_zone_device *ti_thermal;struct device *dev = &pdev->dev; +bool workaround_needed = false;struct k3_j72xx_bandgap *bgp;struct k3_thermal_data *data; -bool workaround_needed = false; -const struct k3_j72xx_bandgap_data *driver_data; -struct thermal_zone_device *ti_thermal; -int *ref_table;struct err_values err_vals;void __iomem *fuse_base; +int ret =0 , val, id; +struct resource *res; +int *ref_table;const s64 golden_factors[] = {-490019999999999936 ,@@ -422,10 +452,10 @@ static int k3_j72xx_bandgap_probe(struct platform_device *pdev)/* Get the sensor count in the VTM */ val =readl (bgp->base +K3_VTM_DEVINFO_PWR0_OFFSET ); - cnt = val &K3_VTM_DEVINFO_PWR0_TEMPSENS_CT_MASK ; - cnt >>=__ffs (K3_VTM_DEVINFO_PWR0_TEMPSENS_CT_MASK ); + bgp->cnt = val &K3_VTM_DEVINFO_PWR0_TEMPSENS_CT_MASK ; + bgp->cnt >>=__ffs (K3_VTM_DEVINFO_PWR0_TEMPSENS_CT_MASK ); - data =devm_kcalloc (bgp->dev, cnt,sizeof (*data),GFP_KERNEL ); + data =devm_kcalloc (bgp->dev, bgp->cnt,sizeof (*data),GFP_KERNEL );if (!data) { ret = -ENOMEM ; goto err_alloc;@@ -449,8 +479,8 @@ static int k3_j72xx_bandgap_probe(struct platform_device *pdev)else init_table (3 , ref_table, pvt_wa_factors); -/* Register the thermal sensors */ -for (id =0 ; id < cnt; id++) { +/* Precompute the derived table & fill each thermal sensor struct */ +for (id =0 ; id < bgp->cnt; id++) { data[id].bgp = bgp; data[id].ctrl_offset =K3_VTM_TMPSENS0_CTRL_OFFSET + id *0x20 ; data[id].stat_offset = data[id].ctrl_offset +@@ -470,13 +500,13 @@ static int k3_j72xx_bandgap_probe(struct platform_device *pdev)else if (id ==0 && !workaround_needed)memcpy (derived_table, ref_table,TABLE_SIZE *4 ); - val =readl (data[id].bgp->cfg2_base + data[id].ctrl_offset); - val |= (K3_VTM_TMPSENS_CTRL_MAXT_OUTRG_EN | -K3_VTM_TMPSENS_CTRL_SOC | -K3_VTM_TMPSENS_CTRL_CLRZ |BIT (4 )); -writel (val, data[id].bgp->cfg2_base + data[id].ctrl_offset); - bgp->ts_data[id] = &data[id]; + } + +k3_j72xx_bandgap_init_hw (bgp); + +/* Register the thermal sensors */ +for (id =0 ; id < bgp->cnt; id++) { ti_thermal =devm_thermal_of_zone_register (bgp->dev, id, &data[id], &k3_of_thermal_ops);if (IS_ERR (ti_thermal)) {@@ -486,21 +516,7 @@ static int k3_j72xx_bandgap_probe(struct platform_device *pdev) } } -/* -* Program TSHUT thresholds -* Step 1: set the thresholds to ~123C and 105C WKUP_VTM_MISC_CTRL2 -* Step 2: WKUP_VTM_TMPSENS_CTRL_j set the MAXT_OUTRG_EN bit -* This is already taken care as per of init -* Step 3: WKUP_VTM_MISC_CTRL set the ANYMAXT_OUTRG_ALERT_EN bit -*/ - high_max =k3_j72xx_bandgap_temp_to_adc_code (MAX_TEMP ); - low_temp =k3_j72xx_bandgap_temp_to_adc_code (COOL_DOWN_TEMP ); - -writel ((low_temp <<16 ) | high_max, data[0 ].bgp->cfg2_base + -K3_VTM_MISC_CTRL2_OFFSET ); -mdelay (100 ); -writel (K3_VTM_ANYMAXT_OUTRG_ALERT_EN , data[0 ].bgp->cfg2_base + -K3_VTM_MISC_CTRL_OFFSET ); +platform_set_drvdata (pdev, bgp);print_look_up_table (dev, ref_table);/* @@ -527,6 +543,35 @@ static void k3_j72xx_bandgap_remove(struct platform_device *pdev)pm_runtime_disable (&pdev->dev); } +static int __maybe_unused k3_j72xx_bandgap_suspend (struct device *dev) +{ +pm_runtime_put_sync (dev); +pm_runtime_disable (dev); +return 0 ; +} + +static int __maybe_unused k3_j72xx_bandgap_resume (struct device *dev) +{ +struct k3_j72xx_bandgap *bgp =dev_get_drvdata (dev); +int ret; + +pm_runtime_enable (dev); + ret =pm_runtime_get_sync (dev); +if (ret <0 ) { +pm_runtime_put_noidle (dev); +pm_runtime_disable (dev); +return ret; + } + +k3_j72xx_bandgap_init_hw (bgp); + +return 0 ; +} + +static const struct dev_pm_ops k3_j72xx_bandgap_pm_ops = { +SET_SYSTEM_SLEEP_PM_OPS (k3_j72xx_bandgap_suspend, k3_j72xx_bandgap_resume) +}; +static const struct k3_j72xx_bandgap_data k3_j72xx_bandgap_j721e_data = { .has_errata_i2128 = true, };@@ -554,6 +599,7 @@ static struct platform_driver k3_j72xx_bandgap_sensor_driver = { .driver = { .name = "k3-j72xx-soc-thermal", .of_match_table = of_k3_j72xx_bandgap_match, + .pm = &k3_j72xx_bandgap_pm_ops, }, };
Signature · 3 lines
Thomas Richard, Bootlin Embedded Linux and Kernel engineering https://bootlin.com
J, KEERTHY
Acked-byQuoted 16 lines · Thomas Richard
Added Keerthy
Quoted 13 lines · Thomas Richard
From: Théo Lebrun <[email protected]>
This add suspend-to-ram support.
The
derived_tableis kept-as is, so the resume is only about pm_runtime_* calls and restoring the same registers as the probe.Extract the hardware initialization procedure to a function called at both probe-time & resume-time.
The probe-time loop is split in two to ensure doing the hardware initialization before registering thermal zones. That ensures our callbacks cannot be called while in bad state.
Thomas,
Thanks for adding suspend/resume support.
FWIW
- Keerthy
Quoted 196 lines
Quoted 196 lines
Signed-off-by Théo Lebrun <[email protected]>Signed-off-by Thomas Richard <[email protected]>---
v2:
- Fix warnings/errors reported by kernel test robotdrivers/thermal/k3_j72xx_bandgap.c | 112 ++++++++++++++++++++--------- 1 file changed, 79 insertions(+), 33 deletions(-)drivers/thermal/k3_j72xx_bandgap.c +79
-33@@ -178,6 +178,7 @@ struct k3_j72xx_bandgap {void __iomem *base;void __iomem *cfg2_base;struct k3_thermal_data *ts_data[K3_VTM_MAX_NUM_TS ]; +int cnt; };/* common data structures */ @@ -338,24 +339,53 @@ static void print_look_up_table(struct device *dev, int *ref_table)dev_dbg (dev,"%d %d %d\n" , i, derived_table[i], ref_table[i]); } +static void k3_j72xx_bandgap_init_hw (struct k3_j72xx_bandgap *bgp) +{ +struct k3_thermal_data *data; +int id, high_max, low_temp; +u32 val; + +for (id =0 ; id < bgp->cnt; id++) { + data = bgp->ts_data[id]; + val =readl (bgp->cfg2_base + data->ctrl_offset); + val |= (K3_VTM_TMPSENS_CTRL_MAXT_OUTRG_EN | +K3_VTM_TMPSENS_CTRL_SOC | +K3_VTM_TMPSENS_CTRL_CLRZ |BIT (4 )); +writel (val, bgp->cfg2_base + data->ctrl_offset); + } + +/* +* Program TSHUT thresholds +* Step 1: set the thresholds to ~123C and 105C WKUP_VTM_MISC_CTRL2 +* Step 2: WKUP_VTM_TMPSENS_CTRL_j set the MAXT_OUTRG_EN bit +* This is already taken care as per of init +* Step 3: WKUP_VTM_MISC_CTRL set the ANYMAXT_OUTRG_ALERT_EN bit +*/ + high_max =k3_j72xx_bandgap_temp_to_adc_code (MAX_TEMP ); + low_temp =k3_j72xx_bandgap_temp_to_adc_code (COOL_DOWN_TEMP ); + +writel ((low_temp <<16 ) | high_max, bgp->cfg2_base +K3_VTM_MISC_CTRL2_OFFSET ); +mdelay (100 ); +writel (K3_VTM_ANYMAXT_OUTRG_ALERT_EN , bgp->cfg2_base +K3_VTM_MISC_CTRL_OFFSET ); +} +struct k3_j72xx_bandgap_data {const bool has_errata_i2128; };static int k3_j72xx_bandgap_probe (struct platform_device *pdev) { -int ret =0 , cnt, val, id; -int high_max, low_temp; -struct resource *res; +const struct k3_j72xx_bandgap_data *driver_data; +struct thermal_zone_device *ti_thermal;struct device *dev = &pdev->dev; +bool workaround_needed = false;struct k3_j72xx_bandgap *bgp;struct k3_thermal_data *data; -bool workaround_needed = false; -const struct k3_j72xx_bandgap_data *driver_data; -struct thermal_zone_device *ti_thermal; -int *ref_table;struct err_values err_vals;void __iomem *fuse_base; +int ret =0 , val, id; +struct resource *res; +int *ref_table;const s64 golden_factors[] = {-490019999999999936 ,@@ -422,10 +452,10 @@ static int k3_j72xx_bandgap_probe(struct platform_device *pdev)/* Get the sensor count in the VTM */ val =readl (bgp->base +K3_VTM_DEVINFO_PWR0_OFFSET ); - cnt = val &K3_VTM_DEVINFO_PWR0_TEMPSENS_CT_MASK ; - cnt >>=__ffs (K3_VTM_DEVINFO_PWR0_TEMPSENS_CT_MASK ); + bgp->cnt = val &K3_VTM_DEVINFO_PWR0_TEMPSENS_CT_MASK ; + bgp->cnt >>=__ffs (K3_VTM_DEVINFO_PWR0_TEMPSENS_CT_MASK ); - data =devm_kcalloc (bgp->dev, cnt,sizeof (*data),GFP_KERNEL ); + data =devm_kcalloc (bgp->dev, bgp->cnt,sizeof (*data),GFP_KERNEL );if (!data) { ret = -ENOMEM ; goto err_alloc;@@ -449,8 +479,8 @@ static int k3_j72xx_bandgap_probe(struct platform_device *pdev)else init_table (3 , ref_table, pvt_wa_factors); -/* Register the thermal sensors */ -for (id =0 ; id < cnt; id++) { +/* Precompute the derived table & fill each thermal sensor struct */ +for (id =0 ; id < bgp->cnt; id++) { data[id].bgp = bgp; data[id].ctrl_offset =K3_VTM_TMPSENS0_CTRL_OFFSET + id *0x20 ; data[id].stat_offset = data[id].ctrl_offset +@@ -470,13 +500,13 @@ static int k3_j72xx_bandgap_probe(struct platform_device *pdev)else if (id ==0 && !workaround_needed)memcpy (derived_table, ref_table,TABLE_SIZE *4 ); - val =readl (data[id].bgp->cfg2_base + data[id].ctrl_offset); - val |= (K3_VTM_TMPSENS_CTRL_MAXT_OUTRG_EN | -K3_VTM_TMPSENS_CTRL_SOC | -K3_VTM_TMPSENS_CTRL_CLRZ |BIT (4 )); -writel (val, data[id].bgp->cfg2_base + data[id].ctrl_offset); - bgp->ts_data[id] = &data[id]; + } + +k3_j72xx_bandgap_init_hw (bgp); + +/* Register the thermal sensors */ +for (id =0 ; id < bgp->cnt; id++) { ti_thermal =devm_thermal_of_zone_register (bgp->dev, id, &data[id], &k3_of_thermal_ops);if (IS_ERR (ti_thermal)) {@@ -486,21 +516,7 @@ static int k3_j72xx_bandgap_probe(struct platform_device *pdev) } } -/* -* Program TSHUT thresholds -* Step 1: set the thresholds to ~123C and 105C WKUP_VTM_MISC_CTRL2 -* Step 2: WKUP_VTM_TMPSENS_CTRL_j set the MAXT_OUTRG_EN bit -* This is already taken care as per of init -* Step 3: WKUP_VTM_MISC_CTRL set the ANYMAXT_OUTRG_ALERT_EN bit -*/ - high_max =k3_j72xx_bandgap_temp_to_adc_code (MAX_TEMP ); - low_temp =k3_j72xx_bandgap_temp_to_adc_code (COOL_DOWN_TEMP ); - -writel ((low_temp <<16 ) | high_max, data[0 ].bgp->cfg2_base + -K3_VTM_MISC_CTRL2_OFFSET ); -mdelay (100 ); -writel (K3_VTM_ANYMAXT_OUTRG_ALERT_EN , data[0 ].bgp->cfg2_base + -K3_VTM_MISC_CTRL_OFFSET ); +platform_set_drvdata (pdev, bgp);print_look_up_table (dev, ref_table);/* @@ -527,6 +543,35 @@ static void k3_j72xx_bandgap_remove(struct platform_device *pdev)pm_runtime_disable (&pdev->dev); } +static int __maybe_unused k3_j72xx_bandgap_suspend (struct device *dev) +{ +pm_runtime_put_sync (dev); +pm_runtime_disable (dev); +return 0 ; +} + +static int __maybe_unused k3_j72xx_bandgap_resume (struct device *dev) +{ +struct k3_j72xx_bandgap *bgp =dev_get_drvdata (dev); +int ret; + +pm_runtime_enable (dev); + ret =pm_runtime_get_sync (dev); +if (ret <0 ) { +pm_runtime_put_noidle (dev); +pm_runtime_disable (dev); +return ret; + } + +k3_j72xx_bandgap_init_hw (bgp); + +return 0 ; +} + +static const struct dev_pm_ops k3_j72xx_bandgap_pm_ops = { +SET_SYSTEM_SLEEP_PM_OPS (k3_j72xx_bandgap_suspend, k3_j72xx_bandgap_resume) +}; +static const struct k3_j72xx_bandgap_data k3_j72xx_bandgap_j721e_data = { .has_errata_i2128 = true, };@@ -554,6 +599,7 @@ static struct platform_driver k3_j72xx_bandgap_sensor_driver = { .driver = { .name = "k3-j72xx-soc-thermal", .of_match_table = of_k3_j72xx_bandgap_match, + .pm = &k3_j72xx_bandgap_pm_ops, }, };