i3c: master: some improvment for i3c master
Frank Li
maintainerv5 cover i3c: master: some improvment for i3c master
There are three major improvement
1. Add actual size in i3c_transfer because i3c allow target early termiate transfer.
2. Add API for i3c_dev_gettstatus_format1 for i3c comand GET_STATUS.
3. svc master add hotjoin support.
4. Add tty over i3c support.
change log see each patches.
Frank Li (7):
i3c: master: add enable(disable) hot join in sys entry
i3c: master: svc: add hot join support
i3c: add actual_len in i3c_priv_xfer
i3c: master: svc: rename read_len as actual_len
i3c: master: svc: return actual transfer data len
i3c: add API i3c_dev_gettstatus_format1() to get target device status
tty: i3c: add TTY over I3C master support
drivers/i3c/device.c | 24 ++ drivers/i3c/internals.h | 1 + drivers/i3c/master.c | 109 +++++++ drivers/i3c/master/svc-i3c-master.c | 95 ++++-- drivers/tty/Kconfig | 13 + drivers/tty/Makefile | 1 + drivers/tty/i3c_tty.c | 443 ++++++++++++++++++++++++++++ include/linux/i3c/device.h | 3 + include/linux/i3c/master.h | 5 + 9 files changed, 677 insertions(+), 17 deletions(-) create mode 100644 drivers/tty/i3c_tty.c
Signature · 1 line
2.34.1
Frank Li
maintainerPATCH v5 1/7 i3c: master: add enable(disable) hot join in sys entry
Add hotjoin entry in sys file system allow user enable/disable hotjoin feature.
Add (*enable(disable)_hotjoin)() to i3c_master_controller_ops. Add api i3c_master_enable(disable)_hotjoin();
---
Notes:
Change from v4 to v5
- using kstrtobool()
> + if (!master ||
> + !master->ops ||
> + !master->ops->enable_hotjoin ||
> + !master->ops->disable_hotjoin
> + )
break into two if, which will be more clear. and one line is 101 chars.
Change from v3 to v4
-none
Change from v1 to v2.
- Hotjoin control by sys entry, default enable hotjoin, which standard i3c feature, user can disable by echo 0 > /sys/bus/i3c/i3c-0/hotjoin
drivers/i3c/master.c | 83 ++++++++++++++++++++++++++++++++++++++ include/linux/i3c/master.h | 5 +++ 2 files changed, 88 insertions(+)
drivers/i3c/master.c +83 -0
@@ -526,6 +526,88 @@ static ssize_t i2c_scl_frequency_show(struct device *dev, }static DEVICE_ATTR_RO (i2c_scl_frequency); +static int i3c_set_hotjoin (struct i3c_master_controller *master,bool enable) +{ +int ret; + +if (!master || !master->ops) +return -EINVAL ; + +if (!master->ops->enable_hotjoin || !master->ops->disable_hotjoin) +return -EINVAL ; + +i3c_bus_normaluse_lock (&master->bus); + +if (enable) + ret = master->ops->enable_hotjoin (master); +else + ret = master->ops->disable_hotjoin (master); + + master->hotjoin = enable; + +i3c_bus_normaluse_unlock (&master->bus); + +return ret; +} + +static ssize_t hotjoin_store (struct device *dev,struct device_attribute *attr, +const char *buf,size_t count) +{ +struct i3c_bus *i3cbus =dev_to_i3cbus (dev); +int ret; +bool res; + +if (!i3cbus->cur_master) +return -EINVAL ; + +if (kstrtobool (buf, &res)) +return -EINVAL ; + + ret =i3c_set_hotjoin (i3cbus->cur_master->common.master, res); +if (ret) +return ret; + +return count; +} + +/* +* i3c_master_enable_hotjoin - Enable hotjoin +* @master: I3C master object +* +* Return: a 0 in case of success, an negative error code otherwise. +*/ +int i3c_master_enable_hotjoin (struct i3c_master_controller *master) +{ +return i3c_set_hotjoin (master, true); +} +EXPORT_SYMBOL_GPL (i3c_master_enable_hotjoin); + +/* +* i3c_master_disable_hotjoin - Disable hotjoin +* @master: I3C master object +* +* Return: a 0 in case of success, an negative error code otherwise. +*/ +int i3c_master_disable_hotjoin (struct i3c_master_controller *master) +{ +return i3c_set_hotjoin (master, false); +} +EXPORT_SYMBOL_GPL (i3c_master_disable_hotjoin); + +static ssize_t hotjoin_show (struct device *dev,struct device_attribute *da,char *buf) +{ +struct i3c_bus *i3cbus =dev_to_i3cbus (dev); +ssize_t ret; + +i3c_bus_normaluse_lock (i3cbus); + ret =sysfs_emit (buf,"%d\n" , i3cbus->cur_master->common.master->hotjoin); +i3c_bus_normaluse_unlock (i3cbus); + +return ret; +} + +static DEVICE_ATTR_RW (hotjoin); +static struct attribute *i3c_masterdev_attrs[] = { &dev_attr_mode.attr, &dev_attr_current_master.attr,
@@ -536,6 +618,7 @@ static struct attribute *i3c_masterdev_attrs[] = { &dev_attr_pid.attr, &dev_attr_dynamic_address.attr, &dev_attr_hdrcap.attr, + &dev_attr_hotjoin.attr,NULL , };ATTRIBUTE_GROUPS (i3c_masterdev);
include/linux/i3c/master.h +5 -0
@@ -452,6 +452,8 @@ struct i3c_master_controller_ops {int (*disable_ibi)(struct i3c_dev_desc *dev);void (*recycle_ibi_slot)(struct i3c_dev_desc *dev,struct i3c_ibi_slot *slot); +int (*enable_hotjoin)(struct i3c_master_controller *master); +int (*disable_hotjoin)(struct i3c_master_controller *master); };/**
@@ -487,6 +489,7 @@ struct i3c_master_controller {const struct i3c_master_controller_ops *ops; unsigned int secondary : 1; unsigned int init_done : 1; + unsigned int hotjoin: 1;struct {struct list_head i3c;struct list_head i2c;
@@ -543,6 +546,8 @@ int i3c_master_register(struct i3c_master_controller *master,const struct i3c_master_controller_ops *ops, bool secondary);void i3c_master_unregister (struct i3c_master_controller *master); +int i3c_master_enable_hotjoin (struct i3c_master_controller *master); +int i3c_master_disable_hotjoin (struct i3c_master_controller *master);/** * i3c_dev_get_master_data() - get master private data attached to an I3C
Signature · 1 line
2.34.1
Frank Li
maintainerPATCH v5 2/7 i3c: master: svc: add hot join support
In reply to Frank LiAdd hot join support for svc master controller. Disable hot join defaultly. User can use sys entry to enable hot join.
---
Notes:
Change from v4 to v5
- default disable hotjoin
- add help func is_events_enabled()
Change from v3 to v4
-fix build warning
All warnings (new ones prefixed by >>):
drivers/i3c/master/svc-i3c-master.c:212: warning: Function parameter or member 'lock' not described in 'svc_i3c_master'
>> drivers/i3c/master/svc-i3c-master.c:212: warning: Function parameter or member 'enabled_events' not described in 'svc_i3c_master'
2 warnings as Errors
drivers/i3c/master/svc-i3c-master.c | 61 +++++++++++++++++++++++++++-- 1 file changed, 57 insertions(+), 4 deletions(-)
drivers/i3c/master/svc-i3c-master.c +57 -4
@@ -128,6 +128,9 @@/* This parameter depends on the implementation and may be tuned */ #define SVC_I3C_FIFO_SIZE 16 +#define SVC_I3C_EVENT_IBI BIT(0) +#define SVC_I3C_EVENT_HOTJOIN BIT(1) +struct svc_i3c_cmd {u8 addr;bool rnw;
@@ -176,6 +179,7 @@ struct svc_i3c_regs_save {* @ibi.tbq_slot: To be queued IBI slot * @ibi.lock: IBI lock * @lock: Transfer lock, protect between IBI work thread and callbacks from master +* @enabled_events: Bit masks for enable events (IBI, HotJoin). */ struct svc_i3c_master {struct i3c_master_controller base;
@@ -205,6 +209,7 @@ struct svc_i3c_master {spinlock_t lock; } ibi;struct mutex lock; +int enabled_events; };/**
@@ -219,6 +224,11 @@ struct svc_i3c_i2c_dev_data {struct i3c_generic_ibi_pool *ibi_pool; }; +static inline bool is_events_enabled (struct svc_i3c_master *master,u32 mask) +{ +return !!(master->enabled_events & mask); +} +static bool svc_i3c_master_error (struct svc_i3c_master *master) {u32 mstatus, merrwarn;
@@ -428,13 +438,16 @@ static void svc_i3c_master_ibi_work(struct work_struct *work)switch (ibitype) {case SVC_I3C_MSTATUS_IBITYPE_IBI : dev =svc_i3c_master_dev_from_addr (master, ibiaddr); -if (!dev) +if (!dev || !is_events_enabled (master,SVC_I3C_EVENT_IBI ))svc_i3c_master_nack_ibi (master);else svc_i3c_master_handle_ibi (master, dev);break ;case SVC_I3C_MSTATUS_IBITYPE_HOT_JOIN : -svc_i3c_master_ack_ibi (master, false); +if (is_events_enabled (master,SVC_I3C_EVENT_HOTJOIN )) +svc_i3c_master_ack_ibi (master, false); +else +svc_i3c_master_nack_ibi (master);break ;case SVC_I3C_MSTATUS_IBITYPE_MASTER_REQUEST :svc_i3c_master_nack_ibi (master);
@@ -471,7 +484,9 @@ static void svc_i3c_master_ibi_work(struct work_struct *work)svc_i3c_master_emit_stop (master);break ;case SVC_I3C_MSTATUS_IBITYPE_HOT_JOIN : -queue_work (master->base.wq, &master->hj_work); +svc_i3c_master_emit_stop (master); +if (is_events_enabled (master,SVC_I3C_EVENT_HOTJOIN )) +queue_work (master->base.wq, &master->hj_work);break ;case SVC_I3C_MSTATUS_IBITYPE_MASTER_REQUEST :default :
@@ -1471,6 +1486,7 @@ static int svc_i3c_master_enable_ibi(struct i3c_dev_desc *dev)return ret; } + master->enabled_events |=SVC_I3C_EVENT_IBI ;svc_i3c_master_enable_interrupts (master,SVC_I3C_MINT_SLVSTART );return i3c_master_enec_locked (m, dev->info.dyn_addr,I3C_CCC_EVENT_SIR );
@@ -1482,7 +1498,9 @@ static int svc_i3c_master_disable_ibi(struct i3c_dev_desc *dev)struct svc_i3c_master *master =to_svc_i3c_master (m);int ret; -svc_i3c_master_disable_interrupts (master); + master->enabled_events &= ~SVC_I3C_EVENT_IBI ; +if (!master->enabled_events) +svc_i3c_master_disable_interrupts (master); ret =i3c_master_disec_locked (m, dev->info.dyn_addr,I3C_CCC_EVENT_SIR );
@@ -1492,6 +1510,39 @@ static int svc_i3c_master_disable_ibi(struct i3c_dev_desc *dev)return ret; } +static int svc_i3c_master_enable_hotjoin (struct i3c_master_controller *m) +{ +struct svc_i3c_master *master =to_svc_i3c_master (m); +int ret; + + ret =pm_runtime_resume_and_get (master->dev); +if (ret <0 ) { +dev_err (master->dev,"<%s> Cannot get runtime PM.\n" , __func__); +return ret; + } + + master->enabled_events |=SVC_I3C_EVENT_HOTJOIN ; + +svc_i3c_master_enable_interrupts (master,SVC_I3C_MINT_SLVSTART ); + +return 0 ; +} + +static int svc_i3c_master_disable_hotjoin (struct i3c_master_controller *m) +{ +struct svc_i3c_master *master =to_svc_i3c_master (m); + + master->enabled_events &= ~SVC_I3C_EVENT_HOTJOIN ; + +if (!master->enabled_events) +svc_i3c_master_disable_interrupts (master); + +pm_runtime_mark_last_busy (master->dev); +pm_runtime_put_autosuspend (master->dev); + +return 0 ; +} +static void svc_i3c_master_recycle_ibi_slot (struct i3c_dev_desc *dev,struct i3c_ibi_slot *slot) {
@@ -1518,6 +1569,8 @@ static const struct i3c_master_controller_ops svc_i3c_master_ops = { .recycle_ibi_slot = svc_i3c_master_recycle_ibi_slot, .enable_ibi = svc_i3c_master_enable_ibi, .disable_ibi = svc_i3c_master_disable_ibi, + .enable_hotjoin = svc_i3c_master_enable_hotjoin, + .disable_hotjoin = svc_i3c_master_disable_hotjoin, };static int svc_i3c_master_prepare_clks (struct svc_i3c_master *master)
Signature · 1 line
2.34.1
Frank Li
maintainerPATCH v5 3/7 i3c: add actual_len in i3c_priv_xfer
In reply to Frank LiIn MIPI I3C Specification:
"Ninth Bit of SDR Target Returned (Read) Data as End-of-Data: In I2C, the ninth Data bit from Target to Controller is an ACK by the Controller. By contrast, in I3C this bit allows the Target to end a Read, and allows the Controller to Abort a Read. In SDR terms, the ninth bit of Read data is referred to as the T-Bit (for ‘Transition’)"
I3C allow devices early terminate data transfer. So need "actual_len" field to indicate how much get by i3c_priv_xfer.
---
Notes:
change from v4 to v5
- Add Miquel review tag
include/linux/i3c/device.h | 2 ++ 1 file changed, 2 insertions(+)
include/linux/i3c/device.h +2 -0
@@ -54,6 +54,7 @@ enum i3c_hdr_mode {* struct i3c_priv_xfer - I3C SDR private transfer * @rnw: encodes the transfer direction. true for a read, false for a write * @len: transfer length in bytes of the transfer +* @actual_len: actual length in bytes are transferred by the controller * @data: input/output buffer * @data.in: input buffer. Must point to a DMA-able buffer * @data.out: output buffer. Must point to a DMA-able buffer
@@ -62,6 +63,7 @@ enum i3c_hdr_mode {struct i3c_priv_xfer {u8 rnw;u16 len; +u16 actual_len;union {void *in;const void *out;
Signature · 1 line
2.34.1
Frank Li
maintainerPATCH v5 4/7 i3c: master: svc: rename read_len as actual_len
In reply to Frank LiI3C transfer (SDR), target can early terminate read transfer. I3C transfer (HDR), target can end write transfer. I2C transfer, target can NACK write transfer.
'actual_len' is better name than 'read_len'.
---
Notes:
change from v4 to v5:
use i3c: master: svc: prefix
drivers/i3c/master/svc-i3c-master.c | 26 +++++++++++++------------- 1 file changed, 13 insertions(+), 13 deletions(-)
drivers/i3c/master/svc-i3c-master.c +13 -13
@@ -137,7 +137,7 @@ struct svc_i3c_cmd {u8 *in;const void *out;unsigned int len; -unsigned int read_len; +unsigned int actual_len;bool continued; };
@@ -1038,7 +1038,7 @@ static int svc_i3c_master_write(struct svc_i3c_master *master,static int svc_i3c_master_xfer (struct svc_i3c_master *master,bool rnw,unsigned int xfer_type,u8 addr,u8 *in,const u8 *out,unsigned int xfer_len, -unsigned int *read_len,bool continued) +unsigned int *actual_len,bool continued) {u32 reg;int ret;
@@ -1051,7 +1051,7 @@ static int svc_i3c_master_xfer(struct svc_i3c_master *master,SVC_I3C_MCTRL_IBIRESP_NACK |SVC_I3C_MCTRL_DIR (rnw) |SVC_I3C_MCTRL_ADDR (addr) | -SVC_I3C_MCTRL_RDTERM (*read_len), +SVC_I3C_MCTRL_RDTERM (*actual_len), master->regs + SVC_I3C_MCTRL); ret = readl_poll_timeout(master->regs + SVC_I3C_MSTATUS, reg,
@@ -1089,7 +1089,7 @@ static int svc_i3c_master_xfer(struct svc_i3c_master *master, goto emit_stop;if (rnw) - *read_len = ret; + *actual_len = ret; ret =readl_poll_timeout (master->regs +SVC_I3C_MSTATUS , reg,SVC_I3C_MSTATUS_COMPLETE (reg),0 ,1000 );
@@ -1171,7 +1171,7 @@ static void svc_i3c_master_start_xfer_locked(struct svc_i3c_master *master) ret =svc_i3c_master_xfer (master, cmd->rnw, xfer->type, cmd->addr, cmd->in, cmd->out, - cmd->len, &cmd->read_len, + cmd->len, &cmd->actual_len, cmd->continued);if (ret)break ;
@@ -1257,7 +1257,7 @@ static int svc_i3c_master_send_bdcast_ccc_cmd(struct svc_i3c_master *master, cmd->in =NULL ; cmd->out = buf; cmd->len = xfer_len; - cmd->read_len =0 ; + cmd->actual_len =0 ; cmd->continued = false;mutex_lock (&master->lock);
@@ -1277,7 +1277,7 @@ static int svc_i3c_master_send_direct_ccc_cmd(struct svc_i3c_master *master, struct i3c_ccc_cmd *ccc) {unsigned int xfer_len = ccc->dests[0 ].payload.len; -unsigned int read_len = ccc->rnw ? xfer_len :0 ; +unsigned int actual_len = ccc->rnw ? xfer_len :0 ;struct svc_i3c_xfer *xfer;struct svc_i3c_cmd *cmd;int ret;
@@ -1295,7 +1295,7 @@ static int svc_i3c_master_send_direct_ccc_cmd(struct svc_i3c_master *master, cmd->in =NULL ; cmd->out = &ccc->id; cmd->len =1 ; - cmd->read_len =0 ; + cmd->actual_len =0 ; cmd->continued = true;/* Directed message */
@@ -1305,7 +1305,7 @@ static int svc_i3c_master_send_direct_ccc_cmd(struct svc_i3c_master *master, cmd->in = ccc->rnw ? ccc->dests[0 ].payload.data :NULL ; cmd->out = ccc->rnw ?NULL : ccc->dests[0 ].payload.data, cmd->len = xfer_len; - cmd->read_len = read_len; + cmd->actual_len = actual_len; cmd->continued = false;mutex_lock (&master->lock);
@@ -1314,8 +1314,8 @@ static int svc_i3c_master_send_direct_ccc_cmd(struct svc_i3c_master *master,svc_i3c_master_dequeue_xfer (master, xfer);mutex_unlock (&master->lock); -if (cmd->read_len != xfer_len) - ccc->dests[0 ].payload.len = cmd->read_len; +if (cmd->actual_len != xfer_len) + ccc->dests[0 ].payload.len = cmd->actual_len; ret = xfer->ret;svc_i3c_master_free_xfer (xfer);
@@ -1365,7 +1365,7 @@ static int svc_i3c_master_priv_xfers(struct i3c_dev_desc *dev, cmd->in = xfers[i].rnw ? xfers[i].data.in :NULL ; cmd->out = xfers[i].rnw ?NULL : xfers[i].data.out; cmd->len = xfers[i].len; - cmd->read_len = xfers[i].rnw ? xfers[i].len :0 ; + cmd->actual_len = xfers[i].rnw ? xfers[i].len :0 ; cmd->continued = (i +1 ) < nxfers; }
@@ -1405,7 +1405,7 @@ static int svc_i3c_master_i2c_xfers(struct i2c_dev_desc *dev, cmd->in = cmd->rnw ? xfers[i].buf :NULL ; cmd->out = cmd->rnw ?NULL : xfers[i].buf; cmd->len = xfers[i].len; - cmd->read_len = cmd->rnw ? xfers[i].len :0 ; + cmd->actual_len = cmd->rnw ? xfers[i].len :0 ; cmd->continued = (i +1 < nxfers); }
Signature · 1 line
2.34.1
Frank Li
maintainerPATCH v5 5/7 i3c: master: svc: return actual transfer data len
In reply to Frank LiI3C allow devices early terminate data transfer. So set "actual_len" to indicate how much data get by i3c_priv_xfer.
---
Notes:
change from v4 to v5
update prefix
add Miquel's review tag
drivers/i3c/master/svc-i3c-master.c | 8 ++++++++ 1 file changed, 8 insertions(+)
drivers/i3c/master/svc-i3c-master.c +8 -0
@@ -138,6 +138,7 @@ struct svc_i3c_cmd {const void *out;unsigned int len;unsigned int actual_len; +struct i3c_priv_xfer *xfer;bool continued; };
@@ -1061,6 +1062,7 @@ static int svc_i3c_master_xfer(struct svc_i3c_master *master,if (readl (master->regs +SVC_I3C_MERRWARN ) &SVC_I3C_MERRWARN_NACK ) { ret = -ENXIO ; + *actual_len =0 ; goto emit_stop; }
@@ -1078,6 +1080,7 @@ static int svc_i3c_master_xfer(struct svc_i3c_master *master,*/ if (SVC_I3C_MSTATUS_IBIWON (reg)) { ret = -ENXIO ; + *actual_len =0 ; goto emit_stop; }
@@ -1173,6 +1176,10 @@ static void svc_i3c_master_start_xfer_locked(struct svc_i3c_master *master) cmd->addr, cmd->in, cmd->out, cmd->len, &cmd->actual_len, cmd->continued); +/* cmd->xfer is NULL if I2C or CCC transfer */ +if (cmd->xfer) + cmd->xfer->actual_len = cmd->actual_len; +if (ret)break ; }
@@ -1360,6 +1367,7 @@ static int svc_i3c_master_priv_xfers(struct i3c_dev_desc *dev,for (i =0 ; i < nxfers; i++) {struct svc_i3c_cmd *cmd = &xfer->cmds[i]; + cmd->xfer = &xfers[i]; cmd->addr = master->addrs[data->index]; cmd->rnw = xfers[i].rnw; cmd->in = xfers[i].rnw ? xfers[i].data.in :NULL ;
Signature · 1 line
2.34.1
Frank Li
maintainerPATCH v5 6/7 i3c: add API i3c_dev_gettstatus_format1() to get target device status
In reply to Frank LiI3C standard 5.1.9.3.15 Get Device Status (GETSTATUS):
Get request for one I3C Target Device to return its current status.
Add API to fetch it with format1.
---
Notes:
Change from v4 to v5
- none
drivers/i3c/device.c | 24 ++++++++++++++++++++++++ drivers/i3c/internals.h | 1 + drivers/i3c/master.c | 26 ++++++++++++++++++++++++++ include/linux/i3c/device.h | 1 + 4 files changed, 52 insertions(+)
drivers/i3c/device.c +24 -0
@@ -196,6 +196,30 @@ void i3c_device_free_ibi(struct i3c_device *dev) }EXPORT_SYMBOL_GPL (i3c_device_free_ibi); +/** +* i3c_device_getstatus_format1() - Get device status with format 1. +* @dev: device for which you want to get status. +* @status: I3C status format 1 +* +* Return: 0 in case of success, a negative error core otherwise. +*/ +int i3c_device_getstatus_format1 (struct i3c_device *dev,u16 *status) +{ +int ret = -EINVAL ; + +if (!status) +return -EINVAL ; + +i3c_bus_normaluse_lock (dev->bus); +if (dev->desc) + ret =i3c_dev_getstatus_format1_locked (dev->desc, status); + +i3c_bus_normaluse_unlock (dev->bus); + +return ret; +} +EXPORT_SYMBOL_GPL (i3c_device_getstatus_format1); +/** * i3cdev_to_dev() - Returns the device embedded in @i3cdev * @i3cdev: I3C device
drivers/i3c/internals.h +1 -0
@@ -24,4 +24,5 @@ int i3c_dev_enable_ibi_locked(struct i3c_dev_desc *dev);int i3c_dev_request_ibi_locked (struct i3c_dev_desc *dev,const struct i3c_ibi_setup *req);void i3c_dev_free_ibi_locked (struct i3c_dev_desc *dev); +int i3c_dev_getstatus_format1_locked (struct i3c_dev_desc *dev,u16 *status);#endif /* I3C_INTERNAL_H */
drivers/i3c/master.c +26 -0
@@ -2923,6 +2923,32 @@ void i3c_dev_free_ibi_locked(struct i3c_dev_desc *dev) dev->ibi =NULL ; } +int i3c_dev_getstatus_format1_locked (struct i3c_dev_desc *dev,u16 *status) +{ +struct i3c_master_controller *master =i3c_dev_get_master (dev); +struct i3c_ccc_getstatus *format1; +struct i3c_ccc_cmd_dest dest; +struct i3c_ccc_cmd cmd; +int ret; + + format1 =i3c_ccc_cmd_dest_init (&dest, dev->info.dyn_addr,sizeof (*format1)); +if (!format1) +return -ENOMEM ; + +i3c_ccc_cmd_init (&cmd, true,I3C_CCC_GETSTATUS , &dest,1 ); + + ret =i3c_master_send_ccc_cmd_locked (master, &cmd); +if (ret) + goto out; + + *status =be16_to_cpu (format1->status); + +out: +i3c_ccc_cmd_dest_cleanup (&dest); + +return ret; +} +static int __init i3c_init (void ) {int res;
include/linux/i3c/device.h +1 -0
@@ -345,4 +345,5 @@ void i3c_device_free_ibi(struct i3c_device *dev);int i3c_device_enable_ibi (struct i3c_device *dev);int i3c_device_disable_ibi (struct i3c_device *dev); +int i3c_device_getstatus_format1 (struct i3c_device *dev,u16 *status);#endif /* I3C_DEV_H */
Signature · 1 line
2.34.1
Frank Li
maintainerPATCH v5 7/7 tty: i3c: add TTY over I3C master support
In reply to Frank LiIn typical embedded Linux systems, UART consoles require at least two pins, TX and RX. In scenarios where I2C/I3C devices like sensors or PMICs are present, we can save these two pins by using this driver. Pins is crucial resources, especially in small chip packages.
This introduces support for using the I3C bus to transfer console tty data, effectively replacing the need for dedicated UART pins. This not only conserves valuable pin resources but also facilitates testing of I3C's advanced features, including early termination, in-band interrupt (IBI) support, and the creation of more complex data patterns. Additionally, it aids in identifying and addressing issues within the I3C controller driver.
---
Notes:
Change from v4 to v5
- send in i3c improvememtn patches.
Change from v2 to v4
- none
Change from v1 to v2
- update commit message.
- using goto for err handle
- using one working queue for all tty-i3c device
- fixed typo found by js
- update kconfig help
- using kfifo
Still below items not be fixed (according to Jiri Slaby's comments)
- rxwork thread: need trigger from two position.
- common thread queue: need some suggestion
Some idea about i3c tty in future
1. early console support
- early console is useful to debug boot problem. It requires as simple
as possible.
i3c SDR mode, 9th bit is parity. I3C target can't block master send out
data. so never block kernel boot even without any expected target connected. i3c master may send out a boardcast message as early console to every target devices. Only a "i3c-usb-acm" can show it to host's minicom. And this "i3c-usb-acm" can plug in at any time. Write a boardcast message is quite simple at I3C controller. After kernel system boot to certain phase, switch to this driver.
2. multi port supports. create multi virtual uart ports, so firmware, such as arm trust firmware can dump message to difference virtual ports.
3. compatible with UART network adaptor, which defined at MIPI DEBUG for I3C spec.
This driver is just first step.
drivers/tty/Kconfig | 13 ++ drivers/tty/Makefile | 1 + drivers/tty/i3c_tty.c | 443 ++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 457 insertions(+) create mode 100644 drivers/tty/i3c_tty.c
drivers/tty/Kconfig +13 -0
@@ -412,6 +412,19 @@ config RPMSG_TTY To compile this driver as a module, choose M here: the module will be called rpmsg_tty. +config I3C_TTY + tristate "TTY over I3C" + depends on I3C + help + Select this options if you'd like use TTY over I3C master controller + + This makes it possible for user-space programs to send and receive + data as a standard tty protocol. I3C provide relatively higher data + transfer rate and less pin numbers, SDA/SCL are shared with other + devices. + + If unsure, say N + endif # TTY source "drivers/tty/serdev/Kconfig"
drivers/tty/Makefile +1 -0
@@ -27,5 +27,6 @@ obj-$(CONFIG_GOLDFISH_TTY) += goldfish.o obj-$(CONFIG_MIPS_EJTAG_FDC_TTY) += mips_ejtag_fdc.o obj-$(CONFIG_VCC) += vcc.o obj-$(CONFIG_RPMSG_TTY) += rpmsg_tty.o +obj-$(CONFIG_I3C_TTY) += i3c_tty.o obj-y += ipwireless/
drivers/tty/i3c_tty.c new file +443 -0
443 lines not on this page · raw message
Signature · 1 line
2.34.1
Miquel Raynal
maintainerRe: [PATCH v5 7/7] tty: i3c: add TTY over I3C master support
Hi Frank,
[email protected] wrote on Thu, 30 Nov 2023 17:44:08 -0500:
Quoted 13 lines
In typical embedded Linux systems, UART consoles require at least two pins, TX and RX. In scenarios where I2C/I3C devices like sensors or PMICs are present, we can save these two pins by using this driver. Pins is crucial resources, especially in small chip packages.
This introduces support for using the I3C bus to transfer console tty data, effectively replacing the need for dedicated UART pins. This not only conserves valuable pin resources but also facilitates testing of I3C's advanced features, including early termination, in-band interrupt (IBI) support, and the creation of more complex data patterns. Additionally, it aids in identifying and addressing issues within the I3C controller driver.
Quoted 6 lines
Signed-off-by Frank Li <[email protected]>---
Notes:
Change from v4 to v5
- send in i3c improvememtn patches.
This is not what I said, I believe this patch and the previous patch should be sent separately.
Thanks,
Miquèl
Jiri Slaby
maintainerRe: [PATCH v5 7/7] tty: i3c: add TTY over I3C master support
In reply to Frank LiQuoted 14 lines · Frank Li
In typical embedded Linux systems, UART consoles require at least two pins, TX and RX. In scenarios where I2C/I3C devices like sensors or PMICs are present, we can save these two pins by using this driver. Pins is crucial resources, especially in small chip packages.
This introduces support for using the I3C bus to transfer console tty data, effectively replacing the need for dedicated UART pins. This not only conserves valuable pin resources but also facilitates testing of I3C's advanced features, including early termination, in-band interrupt (IBI) support, and the creation of more complex data patterns. Additionally, it aids in identifying and addressing issues within the I3C controller driver.
Signed-off-by Frank Li <[email protected]>
...
drivers/tty/Kconfig config RPMSG_TTY · line 419
Quoted 11 lines
drivers/tty/Kconfig +5
-0@@ -412,6 +412,19 @@ config RPMSG_TTY To compile this driver as a module, choose M here: the module will be called rpmsg_tty. +config I3C_TTY + tristate "TTY over I3C" + depends on I3C + help + Select this options if you'd like use TTY over I3C master controller
this option
to use
add a period to the end.
Quoted 11 lines
drivers/tty/Kconfig +8
-0+ + This makes it possible for user-space programs to send and receive + data as a standard tty protocol. I3C provide relatively higher data + transfer rate and less pin numbers, SDA/SCL are shared with other + devices. + + If unsure, say N + endif # TTY source "drivers/tty/serdev/Kconfig"
...
Quoted 3 lines
drivers/tty/i3c_tty.c new file +0
-0@@ -0,0 +1,443 @@
...
drivers/tty/i3c_tty.c line 37
Quoted 6 lines
drivers/tty/i3c_tty.c new file +6
-0+struct ttyi3c_port { +struct tty_port port; +int minor; +spinlock_t xlock;/* protect xmit */ +char tx_buff[I3C_TTY_TRANS_SIZE ]; +char rx_buff[I3C_TTY_TRANS_SIZE ];
These should be u8 as per the other changes throughout the tty layer.
drivers/tty/i3c_tty.c line 43
Quoted 6 lines
drivers/tty/i3c_tty.c new file +6
-0+struct i3c_device *i3cdev; +struct work_struct txwork; +struct work_struct rxwork; +struct completion txcomplete; +unsigned long status; +int buf_overrun;
Can this be ever negative?
drivers/tty/i3c_tty.c line 46
Quoted 3 lines
drivers/tty/i3c_tty.c new file +3
-0+}; + +struct workqueue_struct *workqueue;
Is this related:
Still below items not be fixed (according to Jiri Slaby's comments)
- rxwork thread: need trigger from two position.
- common thread queue: need some suggestion
?
As I don't remember, could you elaborate again why you need your own workqueue? You need to do it in the commit log anyway.
...
Quoted 13 lines
drivers/tty/i3c_tty.c new file +13
-0+static ssize_t i3c_write (struct tty_struct *tty,const unsigned char *buf,size_t count) +{ +struct ttyi3c_port *sport = tty->driver_data; +unsigned long flags; +bool is_empty; +int ret; + +spin_lock_irqsave (&sport->xlock, flags); + ret =kfifo_in (&sport->port.xmit_fifo, buf, count); + is_empty =kfifo_is_empty (&sport->port.xmit_fifo); +spin_unlock_irqrestore (&sport->xlock, flags); + +if (!is_empty)
drivers/tty/i3c_tty.c line 122
Quoted 10 lines
drivers/tty/i3c_tty.c new file +10
-0+queue_work (workqueue, &sport->txwork); + +return ret; +} + +static int i3c_put_char (struct tty_struct *tty,unsigned char ch) +{ +struct ttyi3c_port *sport = tty->driver_data; +unsigned long flags; +int ret =0 ;
Unneeded initialization.
Quoted 7 lines
drivers/tty/i3c_tty.c new file +7
-0+ +spin_lock_irqsave (&sport->xlock, flags); + ret =kfifo_put (&sport->port.xmit_fifo, ch); +spin_unlock_irqrestore (&sport->xlock, flags); + +return ret; +}
...
drivers/tty/i3c_tty.c line 208
Quoted 5 lines
drivers/tty/i3c_tty.c new file +5
-0+static void tty_i3c_rxwork (struct work_struct *work) +{ + struct ttyi3c_port *sport = container_of(work, struct ttyi3c_port, rxwork); +struct i3c_priv_xfer xfers; +int retry =I3C_TTY_RETRY ;
Likely, should be unsigned.
Quoted 40 lines
drivers/tty/i3c_tty.c new file +40
-0+u16 status =BIT (0 ); +int ret; + +memset (&xfers,0 ,sizeof (xfers)); + xfers.data.in = sport->rx_buff; + xfers.len =I3C_TTY_TRANS_SIZE ; + xfers.rnw =1 ; + + do { + if (test_bit(I3C_TTY_RX_STOP, &sport->status)) + break; + + i3c_device_do_priv_xfers(sport->i3cdev, &xfers, 1); + + if (xfers.actual_len) { + ret = tty_insert_flip_string(&sport->port, sport->rx_buff, + xfers.actual_len); + if (ret < xfers.actual_len) + sport->buf_overrun++; + + retry = I3C_TTY_RETRY; + continue; + } + + status = BIT(0); + i3c_device_getstatus_format1(sport->i3cdev, &status); + /* + * Target side needs some time to fill data into fifo. Target side may not + * have hardware update status in real time. Software update status always + * needs some delays. + * + * Generally, target side have circular buffer in memory, it will be moved + * into FIFO by CPU or DMA. 'status' just show if circular buffer empty. But + * there are gap, especially CPU have not response irq to fill FIFO in time. + * So xfers.actual will be zero, wait for little time to avoid flood + * transfer in i3c bus. + */ + usleep_range(I3C_TTY_YIELD_US, 10 * I3C_TTY_YIELD_US); + retry--; +
drivers/tty/i3c_tty.c line 258
Quoted 10 lines
drivers/tty/i3c_tty.c new file +10
-0+ }while (retry && (status &BIT (0 ))); + +tty_flip_buffer_push (&sport->port); +} + +static void tty_i3c_txwork (struct work_struct *work) +{ + struct ttyi3c_port *sport = container_of(work, struct ttyi3c_port, txwork); +struct i3c_priv_xfer xfers; +int retry =I3C_TTY_RETRY ;
Detto.
drivers/tty/i3c_tty.c line 269
Quoted 11 lines
drivers/tty/i3c_tty.c new file +11
-0+unsigned long flags; +int ret; + + xfers.rnw =0 ; + xfers.data.out = sport->tx_buff; + +while (!kfifo_is_empty (&sport->port.xmit_fifo) && retry) { + xfers.len =kfifo_len (&sport->port.xmit_fifo); + xfers.len =min_t (u16,I3C_TTY_TRANS_SIZE , xfers.len); + + xfers.len =kfifo_out_peek (&sport->port.xmit_fifo, sport->tx_buff, xfers.len);
Can this simply be:
xfers.len = kfifo_out_peek(&sport->port.xmit_fifo, sport->tx_buff, I3C_TTY_TRANS_SIZE); ?
drivers/tty/i3c_tty.c line 282
Quoted 13 lines
drivers/tty/i3c_tty.c new file +13
-0+ + ret =i3c_device_do_priv_xfers (sport->i3cdev, &xfers,1 ); +if (ret) { +/* +* Target side may not move data out of FIFO. delay can't resolve problem, +* just reduce some possiblity. Target can't end I3C SDR mode write +* transfer, discard data is reasonable when FIFO overrun. +*/ +usleep_range (I3C_TTY_YIELD_US ,10 *I3C_TTY_YIELD_US ); + retry--; + }else { + retry =I3C_TTY_RETRY ; + ret =kfifo_out (&sport->port.xmit_fifo, sport->tx_buff, xfers.len);
Just to make sure: xfers.len is nor overwritten by i3c_device_do_priv_xfers(), right?
drivers/tty/i3c_tty.c line 107
Quoted 4 lines
drivers/tty/i3c_tty.c new file +4
-0+ } + } + +spin_lock_irqsave (&sport->xlock, flags);
Why do you take the lock here, but not during the kfifo operations above?
Quoted 26 lines
drivers/tty/i3c_tty.c new file +25
-0+if (kfifo_is_empty (&sport->port.xmit_fifo)) +complete (&sport->txcomplete); +spin_unlock_irqrestore (&sport->xlock, flags); +} +static int __init i3c_tty_init (void ) +{ +int ret; + + i3c_tty_driver =tty_alloc_driver (I3C_TTY_MINORS , +TTY_DRIVER_REAL_RAW |TTY_DRIVER_DYNAMIC_DEV ); + +if (IS_ERR (i3c_tty_driver)) +return PTR_ERR (i3c_tty_driver); + + i3c_tty_driver->driver_name ="ttyI3C" ; + i3c_tty_driver->name ="ttyI3C" ; + i3c_tty_driver->minor_start =0 , + i3c_tty_driver->type =TTY_DRIVER_TYPE_SERIAL , + i3c_tty_driver->subtype =SERIAL_TYPE_NORMAL , + i3c_tty_driver->init_termios = tty_std_termios; + i3c_tty_driver->init_termios.c_cflag =B9600 |CS8 |CREAD |HUPCL | +CLOCAL ; + i3c_tty_driver->init_termios.c_lflag =0 ; + +tty_set_operations (i3c_tty_driver, &i3c_tty_ops);
drivers/tty/i3c_tty.c line 412
Quoted 10 lines
drivers/tty/i3c_tty.c new file +10
-0+ + ret =tty_register_driver (i3c_tty_driver); +if (ret) + goto err_tty_register_driver; + + ret =i3c_driver_register (&i3c_driver); +if (ret) + goto err_i3c_driver_register; + + workqueue =alloc_workqueue ("ttyI3C" ,0 ,0 );
Can it happen that you already queue something on this wq, while not allocated yet? I mean: should this be done first in i3c_tty_init()?
Quoted 15 lines
drivers/tty/i3c_tty.c new file +15
-0+if (!workqueue) { + ret =PTR_ERR (workqueue); + goto err_alloc_workqueue; + } + +return 0 ; + +err_alloc_workqueue: +i3c_driver_unregister (&i3c_driver); + +err_i3c_driver_register: +tty_unregister_driver (i3c_tty_driver); + +err_tty_register_driver: +tty_driver_kref_put (i3c_tty_driver);
drivers/tty/i3c_tty.c line 437
Quoted 10 lines
drivers/tty/i3c_tty.c new file +10
-0+ +return ret; +} + +static void __exit i3c_tty_exit(void) +{ +i3c_driver_unregister (&i3c_driver); +tty_unregister_driver (i3c_tty_driver); +tty_driver_kref_put (i3c_tty_driver); +idr_destroy (&i3c_tty_minors);
What about the wq?
Quoted 1 line
+}
regards,
Signature · 2 lines
js suse labs
Frank Li
maintainerRe: [PATCH v5 7/7] tty: i3c: add TTY over I3C master support
Quoted 74 lines · Jiri Slaby
Quoted 14 lines · Frank Li
In typical embedded Linux systems, UART consoles require at least two pins, TX and RX. In scenarios where I2C/I3C devices like sensors or PMICs are present, we can save these two pins by using this driver. Pins is crucial resources, especially in small chip packages.
This introduces support for using the I3C bus to transfer console tty data, effectively replacing the need for dedicated UART pins. This not only conserves valuable pin resources but also facilitates testing of I3C's advanced features, including early termination, in-band interrupt (IBI) support, and the creation of more complex data patterns. Additionally, it aids in identifying and addressing issues within the I3C controller driver.
Signed-off-by Frank Li <[email protected]>...
drivers/tty/Kconfig config RPMSG_TTY · line 418
Quoted 10 lines
drivers/tty/Kconfig +5
-0@@ -412,6 +412,19 @@ config RPMSG_TTY To compile this driver as a module, choose M here: the module will be called rpmsg_tty. +config I3C_TTY + tristate "TTY over I3C" + depends on I3C + help + Select this options if you'd like use TTY over I3C master controllerthis option
to use
add a period to the end.Quoted 10 lines
drivers/tty/Kconfig +8
-0+ + This makes it possible for user-space programs to send and receive + data as a standard tty protocol. I3C provide relatively higher data + transfer rate and less pin numbers, SDA/SCL are shared with other + devices. + + If unsure, say N + endif # TTY source "drivers/tty/serdev/Kconfig"...
Quoted 3 lines
drivers/tty/i3c_tty.c new file +0
-0@@ -0,0 +1,443 @@...
drivers/tty/i3c_tty.c line 37
Quoted 6 lines
drivers/tty/i3c_tty.c new file +6
-0+struct ttyi3c_port { +struct tty_port port; +int minor; +spinlock_t xlock;/* protect xmit */ +char tx_buff[I3C_TTY_TRANS_SIZE ]; +char rx_buff[I3C_TTY_TRANS_SIZE ];These should be u8 as per the other changes throughout the tty layer.
drivers/tty/i3c_tty.c line 43
Quoted 6 lines
drivers/tty/i3c_tty.c new file +6
-0+struct i3c_device *i3cdev; +struct work_struct txwork; +struct work_struct rxwork; +struct completion txcomplete; +unsigned long status; +int buf_overrun;Can this be ever negative?
drivers/tty/i3c_tty.c line 46
Quoted 3 lines
drivers/tty/i3c_tty.c new file +3
-0+}; + +struct workqueue_struct *workqueue;Is this related:
Still below items not be fixed (according to Jiri Slaby's comments)
- rxwork thread: need trigger from two position.
- common thread queue: need some suggestion
?
Quoted 2 lines
As I don't remember, could you elaborate again why you need your own workqueue? You need to do it in the commit log anyway.
I just learn from other drivers, such as USB ACM, usb gadget ACM driver. If use common workqueue, which one prefered.
I will send fixed version after i3c part accepted.
Frank
Quoted 213 lines
...
Quoted 13 lines
drivers/tty/i3c_tty.c new file +13
-0+static ssize_t i3c_write (struct tty_struct *tty,const unsigned char *buf,size_t count) +{ +struct ttyi3c_port *sport = tty->driver_data; +unsigned long flags; +bool is_empty; +int ret; + +spin_lock_irqsave (&sport->xlock, flags); + ret =kfifo_in (&sport->port.xmit_fifo, buf, count); + is_empty =kfifo_is_empty (&sport->port.xmit_fifo); +spin_unlock_irqrestore (&sport->xlock, flags); + +if (!is_empty)drivers/tty/i3c_tty.c line 122
Quoted 10 lines
drivers/tty/i3c_tty.c new file +10
-0+queue_work (workqueue, &sport->txwork); + +return ret; +} + +static int i3c_put_char (struct tty_struct *tty,unsigned char ch) +{ +struct ttyi3c_port *sport = tty->driver_data; +unsigned long flags; +int ret =0 ;Unneeded initialization.
Quoted 7 lines
drivers/tty/i3c_tty.c new file +7
-0+ +spin_lock_irqsave (&sport->xlock, flags); + ret =kfifo_put (&sport->port.xmit_fifo, ch); +spin_unlock_irqrestore (&sport->xlock, flags); + +return ret; +}...
drivers/tty/i3c_tty.c line 208
Quoted 5 lines
drivers/tty/i3c_tty.c new file +5
-0+static void tty_i3c_rxwork (struct work_struct *work) +{ + struct ttyi3c_port *sport = container_of(work, struct ttyi3c_port, rxwork); +struct i3c_priv_xfer xfers; +int retry =I3C_TTY_RETRY ;Likely, should be unsigned.
Quoted 40 lines
drivers/tty/i3c_tty.c new file +40
-0+u16 status =BIT (0 ); +int ret; + +memset (&xfers,0 ,sizeof (xfers)); + xfers.data.in = sport->rx_buff; + xfers.len =I3C_TTY_TRANS_SIZE ; + xfers.rnw =1 ; + + do { + if (test_bit(I3C_TTY_RX_STOP, &sport->status)) + break; + + i3c_device_do_priv_xfers(sport->i3cdev, &xfers, 1); + + if (xfers.actual_len) { + ret = tty_insert_flip_string(&sport->port, sport->rx_buff, + xfers.actual_len); + if (ret < xfers.actual_len) + sport->buf_overrun++; + + retry = I3C_TTY_RETRY; + continue; + } + + status = BIT(0); + i3c_device_getstatus_format1(sport->i3cdev, &status); + /* + * Target side needs some time to fill data into fifo. Target side may not + * have hardware update status in real time. Software update status always + * needs some delays. + * + * Generally, target side have circular buffer in memory, it will be moved + * into FIFO by CPU or DMA. 'status' just show if circular buffer empty. But + * there are gap, especially CPU have not response irq to fill FIFO in time. + * So xfers.actual will be zero, wait for little time to avoid flood + * transfer in i3c bus. + */ + usleep_range(I3C_TTY_YIELD_US, 10 * I3C_TTY_YIELD_US); + retry--; +drivers/tty/i3c_tty.c line 258
Quoted 10 lines
drivers/tty/i3c_tty.c new file +10
-0+ }while (retry && (status &BIT (0 ))); + +tty_flip_buffer_push (&sport->port); +} + +static void tty_i3c_txwork (struct work_struct *work) +{ + struct ttyi3c_port *sport = container_of(work, struct ttyi3c_port, txwork); +struct i3c_priv_xfer xfers; +int retry =I3C_TTY_RETRY ;Detto.
drivers/tty/i3c_tty.c line 269
Quoted 11 lines
drivers/tty/i3c_tty.c new file +11
-0+unsigned long flags; +int ret; + + xfers.rnw =0 ; + xfers.data.out = sport->tx_buff; + +while (!kfifo_is_empty (&sport->port.xmit_fifo) && retry) { + xfers.len =kfifo_len (&sport->port.xmit_fifo); + xfers.len =min_t (u16,I3C_TTY_TRANS_SIZE , xfers.len); + + xfers.len =kfifo_out_peek (&sport->port.xmit_fifo, sport->tx_buff, xfers.len);Can this simply be:
xfers.len =kfifo_out_peek(&sport->port.xmit_fifo, sport->tx_buff, I3C_TTY_TRANS_SIZE);
?drivers/tty/i3c_tty.c line 282
Quoted 13 lines
drivers/tty/i3c_tty.c new file +13
-0+ + ret =i3c_device_do_priv_xfers (sport->i3cdev, &xfers,1 ); +if (ret) { +/* +* Target side may not move data out of FIFO. delay can't resolve problem, +* just reduce some possiblity. Target can't end I3C SDR mode write +* transfer, discard data is reasonable when FIFO overrun. +*/ +usleep_range (I3C_TTY_YIELD_US ,10 *I3C_TTY_YIELD_US ); + retry--; + }else { + retry =I3C_TTY_RETRY ; + ret =kfifo_out (&sport->port.xmit_fifo, sport->tx_buff, xfers.len);Just to make sure: xfers.len is nor overwritten by
i3c_device_do_priv_xfers(), right?drivers/tty/i3c_tty.c line 107
Quoted 4 lines
drivers/tty/i3c_tty.c new file +4
-0+ } + } + +spin_lock_irqsave (&sport->xlock, flags);Why do you take the lock here, but not during the kfifo operations above?
Quoted 26 lines
drivers/tty/i3c_tty.c new file +25
-0+if (kfifo_is_empty (&sport->port.xmit_fifo)) +complete (&sport->txcomplete); +spin_unlock_irqrestore (&sport->xlock, flags); +} +static int __init i3c_tty_init (void ) +{ +int ret; + + i3c_tty_driver =tty_alloc_driver (I3C_TTY_MINORS , +TTY_DRIVER_REAL_RAW |TTY_DRIVER_DYNAMIC_DEV ); + +if (IS_ERR (i3c_tty_driver)) +return PTR_ERR (i3c_tty_driver); + + i3c_tty_driver->driver_name ="ttyI3C" ; + i3c_tty_driver->name ="ttyI3C" ; + i3c_tty_driver->minor_start =0 , + i3c_tty_driver->type =TTY_DRIVER_TYPE_SERIAL , + i3c_tty_driver->subtype =SERIAL_TYPE_NORMAL , + i3c_tty_driver->init_termios = tty_std_termios; + i3c_tty_driver->init_termios.c_cflag =B9600 |CS8 |CREAD |HUPCL | +CLOCAL ; + i3c_tty_driver->init_termios.c_lflag =0 ; + +tty_set_operations (i3c_tty_driver, &i3c_tty_ops);drivers/tty/i3c_tty.c line 412
Quoted 10 lines
drivers/tty/i3c_tty.c new file +10
-0+ + ret =tty_register_driver (i3c_tty_driver); +if (ret) + goto err_tty_register_driver; + + ret =i3c_driver_register (&i3c_driver); +if (ret) + goto err_i3c_driver_register; + + workqueue =alloc_workqueue ("ttyI3C" ,0 ,0 );Can it happen that you already queue something on this wq, while not allocated yet? I mean: should this be done first in
i3c_tty_init()?Quoted 15 lines
drivers/tty/i3c_tty.c new file +15
-0+if (!workqueue) { + ret =PTR_ERR (workqueue); + goto err_alloc_workqueue; + } + +return 0 ; + +err_alloc_workqueue: +i3c_driver_unregister (&i3c_driver); + +err_i3c_driver_register: +tty_unregister_driver (i3c_tty_driver); + +err_tty_register_driver: +tty_driver_kref_put (i3c_tty_driver);drivers/tty/i3c_tty.c line 437
Quoted 10 lines
drivers/tty/i3c_tty.c new file +10
-0+ +return ret; +} + +static void __exit i3c_tty_exit(void) +{ +i3c_driver_unregister (&i3c_driver); +tty_unregister_driver (i3c_tty_driver); +tty_driver_kref_put (i3c_tty_driver); +idr_destroy (&i3c_tty_minors);What about the wq?
Quoted 1 line
+}
regards,
Signature · 2 lines
js suse labs