Skip to contentSkip to conversation

mpt3sas: Update/reload SBR without rebooting HBA

PATCH Applied Ranjan Kumar 2 participants 5 messages Dec 28, 2023 – Jan 30, 2024

Subsystems (2)
lore
Share & tools
lore

Ranjan Kumar

author maintainer
#0 lore raw

v3 cover mpt3sas: Update/reload SBR without rebooting HBA

Support for additional IOCTL to set SBR
Reload bit in the Host Diagnostic register.

v1->v2:
- Fixed Smatch Warning
- Improvised indentation
- Updated driver version

v2->v3:
- Fixed kernel test robot warning
- Fixed W=1 compilation warning reported by test robot

Ranjan Kumar (2):
mpt3sas: Reload SBR without rebooting HBA
mpt3sas: Update driver version to 48.100.00.00

 drivers/scsi/mpt3sas/mpt3sas_base.c  | 99 +++++++++++++++++++---------
 drivers/scsi/mpt3sas/mpt3sas_base.h  |  8 ++-
 drivers/scsi/mpt3sas/mpt3sas_ctl.c   | 54 +++++++++++++++
 drivers/scsi/mpt3sas/mpt3sas_ctl.h   | 10 +++
 drivers/scsi/mpt3sas/mpt3sas_scsih.c |  1 +
 5 files changed, 138 insertions(+), 34 deletions(-)
Signature · 1 line
2.31.1
author maintainer
#1 lore raw

PATCH v3 1/2 mpt3sas: Reload SBR without rebooting HBA

Added a new IOCTL command MPT3ENABLEDIAGSBRRELOAD.
As a part of firmware update operation, applications use this IOCTL command to set the SBR reload bit in the Host Diagnostic register. So that HBA firmware is updated without power-cycling the system.

---
 drivers/scsi/mpt3sas/mpt3sas_base.c  | 99 +++++++++++++++++++---------
 drivers/scsi/mpt3sas/mpt3sas_base.h  |  4 ++
 drivers/scsi/mpt3sas/mpt3sas_ctl.c   | 54 +++++++++++++++
 drivers/scsi/mpt3sas/mpt3sas_ctl.h   | 10 +++
 drivers/scsi/mpt3sas/mpt3sas_scsih.c |  1 +
 5 files changed, 136 insertions(+), 32 deletions(-)
drivers/scsi/mpt3sas/mpt3sas_base.c +67 -32
index 8761bc58d965..fc8c45e15235 100644
@@ -5481,7 +5481,7 @@ mpt3sas_atto_validate_nvram(struct MPT3SAS_ADAPTER *ioc,
  * mpt3sas_atto_get_sas_addr - get the ATTO SAS address from mfg page 1
  *
  * @ioc : per adapter object
- * @*sas_addr : return sas address
+ * @sas_addr : return sas address
  * Return: 0 for success, non-zero for failure.
  */
 static int
@@ -7914,26 +7914,22 @@ mpt3sas_base_validate_event_type(struct MPT3SAS_ADAPTER *ioc, u32 *event_type)
 }
 
 /**
- * _base_diag_reset - the "big hammer" start of day reset
- * @ioc: per adapter object
- *
- * Return: 0 for success, non-zero for failure.
- */
-static int
-_base_diag_reset(struct MPT3SAS_ADAPTER *ioc)
-{
-	u32 host_diagnostic;
-	u32 ioc_state;
-	u32 count;
-	u32 hcb_size;
-
-	ioc_info(ioc, "sending diag reset !!\n");
-
-	pci_cfg_access_lock(ioc->pdev);
+* mpt3sas_base_unlock_and_get_host_diagnostic- enable Host Diagnostic Register writes
+* @ioc: per adapter object
+* @host_diagnostic: host diagnostic register content
+*
+* Return: 0 for success, non-zero for failure.
+*/
 
-	drsprintk(ioc, ioc_info(ioc, "clear interrupts\n"));
+int
+mpt3sas_base_unlock_and_get_host_diagnostic(struct MPT3SAS_ADAPTER *ioc,
+	u32 *host_diagnostic)
+{
 
+	u32 count;
+	*host_diagnostic = 0;
 	count = 0;
+
 	do {
 		/* Write magic sequence to WriteSequence register
 		 * Loop until in diagnostic mode
@@ -7952,30 +7948,67 @@ _base_diag_reset(struct MPT3SAS_ADAPTER *ioc)
 
 		if (count++ > 20) {
 			ioc_info(ioc,
-			    "Stop writing magic sequence after 20 retries\n");
+				    "Stop writing magic sequence after 20 retries\n");
 			_base_dump_reg_set(ioc);
-			goto out;
+			return -EFAULT;
 		}
 
-		host_diagnostic = ioc->base_readl_ext_retry(&ioc->chip->HostDiagnostic);
+		*host_diagnostic = ioc->base_readl_ext_retry(&ioc->chip->HostDiagnostic);
 		drsprintk(ioc,
-			  ioc_info(ioc, "wrote magic sequence: count(%d), host_diagnostic(0x%08x)\n",
-				   count, host_diagnostic));
+			     ioc_info(ioc, "wrote magic sequence: count(%d), host_diagnostic(0x%08x)\n",
+				     count, *host_diagnostic));
 
-	} while ((host_diagnostic & MPI2_DIAG_DIAG_WRITE_ENABLE) == 0);
+	} while ((*host_diagnostic & MPI2_DIAG_DIAG_WRITE_ENABLE) == 0);
+	return 0;
+}
 
-	hcb_size = ioc->base_readl(&ioc->chip->HCBSize);
+/**
+ * mpt3sas_base_lock_host_diagnostic: Disable Host Diagnostic Register writes
+ * @ioc: per adapter object
+ */
 
+void
+mpt3sas_base_lock_host_diagnostic(struct MPT3SAS_ADAPTER *ioc)
+{
+	drsprintk(ioc, ioc_info(ioc, "disable writes to the diagnostic register\n"));
+	writel(MPI2_WRSEQ_FLUSH_KEY_VALUE, &ioc->chip->WriteSequence);
+}
+
+/**
+ * _base_diag_reset - the "big hammer" start of day reset
+ * @ioc: per adapter object
+ *
+ * Return: 0 for success, non-zero for failure.
+ */
+static int
+_base_diag_reset(struct MPT3SAS_ADAPTER *ioc)
+{
+	u32 host_diagnostic;
+	u32 ioc_state;
+	u32 count;
+	u32 hcb_size;
+
+	ioc_info(ioc, "sending diag reset !!\n");
+
+	pci_cfg_access_lock(ioc->pdev);
+
+	drsprintk(ioc, ioc_info(ioc, "clear interrupts\n"));
+
+	mutex_lock(&ioc->hostdiag_unlock_mutex);
+	if (mpt3sas_base_unlock_and_get_host_diagnostic(ioc, &host_diagnostic))
+		goto out;
+
+	hcb_size = ioc->base_readl(&ioc->chip->HCBSize);
 	drsprintk(ioc, ioc_info(ioc, "diag reset: issued\n"));
 	writel(host_diagnostic | MPI2_DIAG_RESET_ADAPTER,
 	     &ioc->chip->HostDiagnostic);
 
-	/*This delay allows the chip PCIe hardware time to finish reset tasks*/
+	/* This delay allows the chip PCIe hardware time to finish reset tasks */
 	msleep(MPI2_HARD_RESET_PCIE_FIRST_READ_DELAY_MICRO_SEC/1000);
 
 	/* Approximately 300 second max wait */
 	for (count = 0; count < (300000000 /
-		MPI2_HARD_RESET_PCIE_SECOND_READ_DELAY_MICRO_SEC); count++) {
+	    MPI2_HARD_RESET_PCIE_SECOND_READ_DELAY_MICRO_SEC); count++) {
 
 		host_diagnostic = ioc->base_readl_ext_retry(&ioc->chip->HostDiagnostic);
 
@@ -7988,13 +8021,15 @@ _base_diag_reset(struct MPT3SAS_ADAPTER *ioc)
 		if (!(host_diagnostic & MPI2_DIAG_RESET_ADAPTER))
 			break;
 
-		msleep(MPI2_HARD_RESET_PCIE_SECOND_READ_DELAY_MICRO_SEC / 1000);
+		/* Wait to pass the second read delay window */
+		msleep(MPI2_HARD_RESET_PCIE_SECOND_READ_DELAY_MICRO_SEC/1000);
 	}
 
 	if (host_diagnostic & MPI2_DIAG_HCB_MODE) {
 
 		drsprintk(ioc,
-			  ioc_info(ioc, "restart the adapter assuming the HCB Address points to good F/W\n"));
+			ioc_info(ioc, "restart the adapter assuming the\n"
+					"HCB Address points to good F/W\n"));
 		host_diagnostic &= ~MPI2_DIAG_BOOT_DEVICE_SELECT_MASK;
 		host_diagnostic |= MPI2_DIAG_BOOT_DEVICE_SELECT_HCDW;
 		writel(host_diagnostic, &ioc->chip->HostDiagnostic);
@@ -8008,9 +8043,8 @@ _base_diag_reset(struct MPT3SAS_ADAPTER *ioc)
 	writel(host_diagnostic & ~MPI2_DIAG_HOLD_IOC_RESET,
 	    &ioc->chip->HostDiagnostic);
 
-	drsprintk(ioc,
-		  ioc_info(ioc, "disable writes to the diagnostic register\n"));
-	writel(MPI2_WRSEQ_FLUSH_KEY_VALUE, &ioc->chip->WriteSequence);
+	mpt3sas_base_lock_host_diagnostic(ioc);
+	mutex_unlock(&ioc->hostdiag_unlock_mutex);
 
 	drsprintk(ioc, ioc_info(ioc, "Wait for FW to go to the READY state\n"));
 	ioc_state = _base_wait_on_iocstate(ioc, MPI2_IOC_STATE_READY, 20);
@@ -8028,6 +8062,7 @@ _base_diag_reset(struct MPT3SAS_ADAPTER *ioc)
  out:
 	pci_cfg_access_unlock(ioc->pdev);
 	ioc_err(ioc, "diag reset: FAILED\n");
+	mutex_unlock(&ioc->hostdiag_unlock_mutex);
 	return -EFAULT;
 }
 
drivers/scsi/mpt3sas/mpt3sas_base.h +4 -0
index 6d0bc8c66700..de60ef8a7908 100644
@@ -1366,6 +1366,7 @@ struct MPT3SAS_ADAPTER {
 	u8		got_task_abort_from_ioctl;
 
 	struct mutex	reset_in_progress_mutex;
+	struct mutex    hostdiag_unlock_mutex;
 	spinlock_t	ioc_reset_in_progress_lock;
 	u8		ioc_link_reset_in_progress;
 
@@ -1790,6 +1791,9 @@ void mpt3sas_base_disable_msix(struct MPT3SAS_ADAPTER *ioc);
 int mpt3sas_blk_mq_poll(struct Scsi_Host *shost, unsigned int queue_num);
 void mpt3sas_base_pause_mq_polling(struct MPT3SAS_ADAPTER *ioc);
 void mpt3sas_base_resume_mq_polling(struct MPT3SAS_ADAPTER *ioc);
+int mpt3sas_base_unlock_and_get_host_diagnostic(struct MPT3SAS_ADAPTER *ioc,
+	u32 *host_diagnostic);
+void mpt3sas_base_lock_host_diagnostic(struct MPT3SAS_ADAPTER *ioc);
 
 /* scsih shared API */
 struct scsi_cmnd *mpt3sas_scsih_scsi_lookup_get(struct MPT3SAS_ADAPTER *ioc,
drivers/scsi/mpt3sas/mpt3sas_ctl.c +54 -0

66 lines not on this page · raw message

drivers/scsi/mpt3sas/mpt3sas_ctl.h +10 -0
index 8f6ffb40261c..171709e91006 100644
@@ -98,6 +98,8 @@
 	struct mpt3_diag_read_buffer)
 #define MPT3ADDNLDIAGQUERY _IOWR(MPT3_MAGIC_NUMBER, 32, \
 	struct mpt3_addnl_diag_query)
+#define MPT3ENABLEDIAGSBRRELOAD _IOWR(MPT3_MAGIC_NUMBER, 33, \
+	struct mpt3_enable_diag_sbr_reload)
 
 /* Trace Buffer default UniqueId */
 #define MPT2DIAGBUFFUNIQUEID (0x07075900)
@@ -448,4 +450,12 @@ struct mpt3_addnl_diag_query {
 	uint32_t reserved2[2];
 };
 
+/**
+ * struct mpt3_enable_diag_sbr_reload - enable sbr reload
+ * @hdr - generic header
+ */
+struct mpt3_enable_diag_sbr_reload {
+	struct mpt3_ioctl_header hdr;
+};
+
 #endif /* MPT3SAS_CTL_H_INCLUDED */
drivers/scsi/mpt3sas/mpt3sas_scsih.c +1 -0
index 51b5788da040..ef8ee93005ea 100644
@@ -12240,6 +12240,7 @@ _scsih_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 
 	/* misc semaphores and spin locks */
 	mutex_init(&ioc->reset_in_progress_mutex);
+	mutex_init(&ioc->hostdiag_unlock_mutex);
 	/* initializing pci_access_mutex lock */
 	mutex_init(&ioc->pci_access_mutex);
 	spin_lock_init(&ioc->ioc_reset_in_progress_lock);
Signature · 1 line
2.31.1
author maintainer
#2 lore raw

PATCH v3 2/2 mpt3sas: Update driver version to 48.100.00.00

In reply to Ranjan Kumar

Update driver version to 48.100.00.00

---
 drivers/scsi/mpt3sas/mpt3sas_base.h | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/scsi/mpt3sas/mpt3sas_base.h +2 -2
index de60ef8a7908..bf100a4ebfc3 100644
@@ -77,8 +77,8 @@
 #define MPT3SAS_DRIVER_NAME		"mpt3sas"
 #define MPT3SAS_AUTHOR "Avago Technologies <[email protected]>"
 #define MPT3SAS_DESCRIPTION	"LSI MPT Fusion SAS 3.0 Device Driver"
-#define MPT3SAS_DRIVER_VERSION		"43.100.00.00"
-#define MPT3SAS_MAJOR_VERSION		43
+#define MPT3SAS_DRIVER_VERSION		"48.100.00.00"
+#define MPT3SAS_MAJOR_VERSION		48
 #define MPT3SAS_MINOR_VERSION		100
 #define MPT3SAS_BUILD_VERSION		0
 #define MPT3SAS_RELEASE_VERSION	00
Signature · 1 line
2.31.1
#3 lore raw
In reply to Ranjan Kumar

Ranjan,

Quoted 2 lines

Support for additional IOCTL to set SBR
Reload bit in the Host Diagnostic register.

Applied to 6.9/scsi-staging, thanks!

Signature · 1 line
Martin K. Petersen	Oracle Linux Engineering
#4 lore raw
In reply to Ranjan Kumar
Quoted 9 lines · Ranjan Kumar

Support for additional IOCTL to set SBR
Reload bit in the Host Diagnostic register.

v1->v2:
- Fixed Smatch Warning
- Improvised indentation
- Updated driver version

[...]

Applied to 6.9/scsi-queue, thanks!

[1/2] mpt3sas: Reload SBR without rebooting HBA

      https://git.kernel.org/mkp/scsi/c/c0767560b012
[2/2] mpt3sas: Update driver version to 48.100.00.00
      https://git.kernel.org/mkp/scsi/c/a34fc8c7361c
Signature · 1 line
Martin K. Petersen	Oracle Linux Engineering