Skip to contentSkip to conversation

pwm: imx27: workaround of the pwm output bug

PATCH Superseded [email protected] 5 participants 14 messages Dec 29, 2023 – Mar 5, 2024

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 pwm: imx27: workaround of the pwm output bug

From: Clark Wang <[email protected]>

This fixes the pwm output bug when decrease the duty cycle. This is a limited workaround for the PWM IP issue TKT0577206.

Root cause:
When the SAR FIFO is empty, the new write value will be directly applied to SAR even the current period is not over.
If the new SAR value is less than the old one, and the counter is greater than the new SAR value, the current period will not filp the level. This will result in a pulse with a duty cycle of 100%.

Workaround:
Add an old value SAR write before updating the new duty cycle to SAR. This will keep the new value is always in a not empty fifo, and can be wait to update after a period finished.

Limitation:
This workaround can only solve this issue when the PWM period is longer than 2us(or <500KHz).

---
 drivers/pwm/pwm-imx27.c | 67 ++++++++++++++++++++++++++++++++++++++---
 1 file changed, 62 insertions(+), 5 deletions(-)
drivers/pwm/pwm-imx27.c +62 -5
index 29a3089c534c..c21b2a9f02ae 100644
@@ -21,11 +21,13 @@
 #include <linux/platform_device.h>
 #include <linux/pwm.h>
 #include <linux/slab.h>
+#include <linux/spinlock.h>
 
 #define MX3_PWMCR			0x00    /* PWM Control Register */
 #define MX3_PWMSR			0x04    /* PWM Status Register */
 #define MX3_PWMSAR			0x0C    /* PWM Sample Register */
 #define MX3_PWMPR			0x10    /* PWM Period Register */
+#define MX3_PWMCNR			0x14    /* PWM Counter Register */
 
 #define MX3_PWMCR_FWM			GENMASK(27, 26)
 #define MX3_PWMCR_STOPEN		BIT(25)
@@ -91,6 +93,7 @@ struct pwm_imx27_chip {
 	 * value to return in that case.
 	 */
 	unsigned int duty_cycle;
+	spinlock_t lock;
 };
 
 #define to_pwm_imx27_chip(chip)	container_of(chip, struct pwm_imx27_chip, chip)
@@ -203,10 +206,10 @@ static void pwm_imx27_wait_fifo_slot(struct pwm_chip *chip,
 
 	sr = readl(imx->mmio_base + MX3_PWMSR);
 	fifoav = FIELD_GET(MX3_PWMSR_FIFOAV, sr);
-	if (fifoav == MX3_PWMSR_FIFOAV_4WORDS) {
+	if (fifoav >= MX3_PWMSR_FIFOAV_3WORDS) {
 		period_ms = DIV_ROUND_UP_ULL(pwm_get_period(pwm),
 					 NSEC_PER_MSEC);
-		msleep(period_ms);
+		msleep(period_ms * (fifoav - 2));
 
 		sr = readl(imx->mmio_base + MX3_PWMSR);
 		if (fifoav == FIELD_GET(MX3_PWMSR_FIFOAV, sr))
@@ -217,13 +220,15 @@ static void pwm_imx27_wait_fifo_slot(struct pwm_chip *chip,
 static int pwm_imx27_apply(struct pwm_chip *chip, struct pwm_device *pwm,
 			   const struct pwm_state *state)
 {
-	unsigned long period_cycles, duty_cycles, prescale;
+	unsigned long period_cycles, duty_cycles, prescale, counter_check, flags;
 	struct pwm_imx27_chip *imx = to_pwm_imx27_chip(chip);
+	void __iomem *reg_sar = imx->mmio_base + MX3_PWMSAR;
+	__force u32 sar_last, sar_current;
 	struct pwm_state cstate;
 	unsigned long long c;
 	unsigned long long clkrate;
 	int ret;
-	u32 cr;
+	u32 cr, timeout = 1000;
 
 	pwm_get_state(pwm, &cstate);
 
@@ -264,7 +269,57 @@ static int pwm_imx27_apply(struct pwm_chip *chip, struct pwm_device *pwm,
 		pwm_imx27_sw_reset(chip);
 	}
 
-	writel(duty_cycles, imx->mmio_base + MX3_PWMSAR);
+	/*
+	 * This is a limited workaround. When the SAR FIFO is empty, the new
+	 * write value will be directly applied to SAR even the current period
+	 * is not over.
+	 * If the new SAR value is less than the old one, and the counter is
+	 * greater than the new SAR value, the current period will not filp
+	 * the level. This will result in a pulse with a duty cycle of 100%.
+	 * So, writing the current value of the SAR to SAR here before updating
+	 * the new SAR value can avoid this issue.
+	 *
+	 * Add a spin lock and turn off the interrupt to ensure that the
+	 * real-time performance can be guaranteed as much as possible when
+	 * operating the following operations.
+	 *
+	 * 1. Add a threshold of 1.5us. If the time T between the read current
+	 * count value CNR and the end of the cycle is less than 1.5us, wait
+	 * for T to be longer than 1.5us before updating the SAR register.
+	 * This is to avoid the situation that when the first SAR is written,
+	 * the current cycle just ends and the SAR FIFO that just be written
+	 * is emptied again.
+	 *
+	 * 2. Use __raw_writel() to minimize the interval between two writes to
+	 * the SAR register to increase the fastest pwm frequency supported.
+	 *
+	 * When the PWM period is longer than 2us(or <500KHz), this workaround
+	 * can solve this problem.
+	 */
+	if (duty_cycles < imx->duty_cycle) {
+		c = clkrate * 1500;
+		do_div(c, NSEC_PER_SEC);
+		counter_check = c;
+		sar_last = cpu_to_le32(imx->duty_cycle);
+		sar_current = cpu_to_le32(duty_cycles);
+
+		spin_lock_irqsave(&imx->lock, flags);
+		if (state->period >= 2000) {
+			while ((period_cycles -
+				readl_relaxed(imx->mmio_base + MX3_PWMCNR))
+				< counter_check) {
+				if (!--timeout)
+					break;
+			};
+		}
+		if (!(MX3_PWMSR_FIFOAV &
+		      readl_relaxed(imx->mmio_base + MX3_PWMSR)))
+			__raw_writel(sar_last, reg_sar);
+		__raw_writel(sar_current, reg_sar);
+		spin_unlock_irqrestore(&imx->lock, flags);
+	} else
+		writel(duty_cycles, imx->mmio_base + MX3_PWMSAR);
+
 	writel(period_cycles, imx->mmio_base + MX3_PWMPR);
 
 	/*
@@ -325,6 +380,8 @@ static int pwm_imx27_probe(struct platform_device *pdev)
 		return dev_err_probe(&pdev->dev, PTR_ERR(imx->clk_per),
 				     "failed to get peripheral clock\n");
 
+	spin_lock_init(&imx->lock);
+	imx->duty_cycle = 0;
 	imx->chip.ops = &pwm_imx27_ops;
 	imx->chip.dev = &pdev->dev;
 	imx->chip.npwm = 1;
Signature · 1 line
2.25.1
#1 lore raw
kernel test robot noticed the following build warnings:

Hi,

kernel test robot noticed the following build warnings:

[auto build test WARNING on thierry-reding-pwm/for-next] [also build test WARNING on linus/master v6.7-rc7 next-20231222] [If your patch is applied to the wrong git tree, kindly drop us a note. And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch#_base_tree_information]

url:    https://github.com/intel-lab-lkp/linux/commits/pratikmanvar09-gmail-com/pwm-imx27-workaround-of-the-pwm-output-bug/20231229-143435
base:   https://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm.git for-next
patch link:    https://lore.kernel.org/r/20231229063013.1786-1-pratikmanvar09%40gmail.com
patch subject: [PATCH] pwm: imx27: workaround of the pwm output bug
config: arm-randconfig-r133-20231230 (https://download.01.org/0day-ci/archive/20231230/[email protected]/config)
compiler: clang version 18.0.0git (https://github.com/llvm/llvm-project 8a4266a626914765c0c69839e8a51be383013c1a)
reproduce: (https://download.01.org/0day-ci/archive/20231230/[email protected]/reproduce)

If you fix the issue in a separate patch/commit (i.e. not just a new version of the same patch/commit), kindly add following tags
| Reported-by: kernel test robot <[email protected]>
| Closes: https://lore.kernel.org/oe-kbuild-all/[email protected]/

sparse warnings: (new ones prefixed by >>)

>> drivers/pwm/pwm-imx27.c:303:26: sparse: sparse: incorrect type in assignment (different base types) @@     expected unsigned int [usertype] sar_last @@     got restricted __le32 [usertype] @@
   drivers/pwm/pwm-imx27.c:303:26: sparse:     expected unsigned int [usertype] sar_last
   drivers/pwm/pwm-imx27.c:303:26: sparse:     got restricted __le32 [usertype]
>> drivers/pwm/pwm-imx27.c:304:29: sparse: sparse: incorrect type in assignment (different base types) @@     expected unsigned int [usertype] sar_current @@     got restricted __le32 [usertype] @@

drivers/pwm/pwm-imx27.c:304:29: sparse: expected unsigned int [usertype] sar_current
drivers/pwm/pwm-imx27.c:304:29: sparse: got restricted __le32 [usertype]

vim +303 drivers/pwm/pwm-imx27.c

219
220 static int pwm_imx27_apply(struct pwm_chip *chip, struct pwm_device *pwm,
221 const struct pwm_state *state)
222 {
223 unsigned long period_cycles, duty_cycles, prescale, counter_check, flags;
224 struct pwm_imx27_chip *imx = to_pwm_imx27_chip(chip);
225 void __iomem *reg_sar = imx->mmio_base + MX3_PWMSAR;
226 __force u32 sar_last, sar_current;
227 struct pwm_state cstate;
228 unsigned long long c;
229 unsigned long long clkrate;
230 int ret;
231 u32 cr, timeout = 1000;
232
233 pwm_get_state(pwm, &cstate);
234
235 clkrate = clk_get_rate(imx->clk_per);
236 c = clkrate * state->period;
237
238 do_div(c, NSEC_PER_SEC);
239 period_cycles = c;
240
241 prescale = period_cycles / 0x10000 + 1;
242
243 period_cycles /= prescale;
244 c = clkrate * state->duty_cycle;
245 do_div(c, NSEC_PER_SEC);
246 duty_cycles = c;
247 duty_cycles /= prescale;
248
249 /*
250 * according to imx pwm RM, the real period value should be PERIOD
251 * value in PWMPR plus 2.
252 */
253 if (period_cycles > 2)
254 period_cycles -= 2;
255 else
256 period_cycles = 0;
257
258 /*
259 * Wait for a free FIFO slot if the PWM is already enabled, and flush
260 * the FIFO if the PWM was disabled and is about to be enabled.
261 */
262 if (cstate.enabled) {
263 pwm_imx27_wait_fifo_slot(chip, pwm);
264 } else {
265 ret = pwm_imx27_clk_prepare_enable(imx);
266 if (ret)
267 return ret;
268
269 pwm_imx27_sw_reset(chip);
270 }
271
272 /*
273 * This is a limited workaround. When the SAR FIFO is empty, the new
274 * write value will be directly applied to SAR even the current period
275 * is not over.
276 * If the new SAR value is less than the old one, and the counter is
277 * greater than the new SAR value, the current period will not filp
278 * the level. This will result in a pulse with a duty cycle of 100%.
279 * So, writing the current value of the SAR to SAR here before updating
280 * the new SAR value can avoid this issue.
281 *
282 * Add a spin lock and turn off the interrupt to ensure that the
283 * real-time performance can be guaranteed as much as possible when
284 * operating the following operations.
285 *
286 * 1. Add a threshold of 1.5us. If the time T between the read current
287 * count value CNR and the end of the cycle is less than 1.5us, wait
288 * for T to be longer than 1.5us before updating the SAR register.
289 * This is to avoid the situation that when the first SAR is written,
290 * the current cycle just ends and the SAR FIFO that just be written
291 * is emptied again.
292 *
293 * 2. Use __raw_writel() to minimize the interval between two writes to
294 * the SAR register to increase the fastest pwm frequency supported.
295 *
296 * When the PWM period is longer than 2us(or <500KHz), this workaround
297 * can solve this problem.
298 */
299 if (duty_cycles < imx->duty_cycle) {
300 c = clkrate * 1500;
301 do_div(c, NSEC_PER_SEC);
302 counter_check = c;

 > 303			sar_last = cpu_to_le32(imx->duty_cycle);
 > 304			sar_current = cpu_to_le32(duty_cycles);
   305	
   306			spin_lock_irqsave(&imx->lock, flags);
   307			if (state->period >= 2000) {
   308				while ((period_cycles -
   309					readl_relaxed(imx->mmio_base + MX3_PWMCNR))
   310					< counter_check) {
   311					if (!--timeout)
   312						break;
   313				};
   314			}
   315			if (!(MX3_PWMSR_FIFOAV &
   316			      readl_relaxed(imx->mmio_base + MX3_PWMSR)))
   317				__raw_writel(sar_last, reg_sar);
   318			__raw_writel(sar_current, reg_sar);
   319			spin_unlock_irqrestore(&imx->lock, flags);
   320		} else
   321			writel(duty_cycles, imx->mmio_base + MX3_PWMSAR);
   322	
   323		writel(period_cycles, imx->mmio_base + MX3_PWMPR);
   324	
   325		/*
   326		 * Store the duty cycle for future reference in cases where the
   327		 * MX3_PWMSAR register can't be read (i.e. when the PWM is disabled).
   328		 */
   329		imx->duty_cycle = duty_cycles;
   330	
   331		cr = MX3_PWMCR_PRESCALER_SET(prescale) |
   332		     MX3_PWMCR_STOPEN | MX3_PWMCR_DOZEN | MX3_PWMCR_WAITEN |
   333		     FIELD_PREP(MX3_PWMCR_CLKSRC, MX3_PWMCR_CLKSRC_IPG_HIGH) |
   334		     MX3_PWMCR_DBGEN;

335
336 if (state->polarity == PWM_POLARITY_INVERSED)
337 cr |= FIELD_PREP(MX3_PWMCR_POUTC,
338 MX3_PWMCR_POUTC_INVERTED);
339
340 if (state->enabled)
341 cr |= MX3_PWMCR_EN;
342
343 writel(cr, imx->mmio_base + MX3_PWMCR);
344
345 if (!state->enabled)
346 pwm_imx27_clk_disable_unprepare(imx);
347
348 return 0;
349 }
350

Signature · 2 lines
0-DAY CI Kernel Test Service
https://github.com/intel/lkp-tests/wiki
#2 lore raw

PATCH v2 1/1 pwm: imx27: workaround of the pwm output bug

From: Clark Wang <[email protected]>

This fixes the pwm output bug when decrease the duty cycle. This is a limited workaround for the PWM IP issue TKT0577206.

Root cause:
When the SAR FIFO is empty, the new write value will be directly applied to SAR even the current period is not over.
If the new SAR value is less than the old one, and the counter is greater than the new SAR value, the current period will not filp the level. This will result in a pulse with a duty cycle of 100%.

Workaround:
Add an old value SAR write before updating the new duty cycle to SAR. This will keep the new value is always in a not empty fifo, and can be wait to update after a period finished.

Limitation:
This workaround can only solve this issue when the PWM period is longer than 2us(or <500KHz).

---
V1 -> V2: fix sparse warnings reported-by: kernel test robot <[email protected]>

           Closes: https://lore.kernel.org/oe-kbuild-all/[email protected]/
 drivers/pwm/pwm-imx27.c | 67 ++++++++++++++++++++++++++++++++++++++---
 1 file changed, 62 insertions(+), 5 deletions(-)
drivers/pwm/pwm-imx27.c +62 -5
index 7d9bc43f12b0..1e500a5bf564 100644
@@ -21,11 +21,13 @@
 #include <linux/platform_device.h>
 #include <linux/pwm.h>
 #include <linux/slab.h>
+#include <linux/spinlock.h>
 
 #define MX3_PWMCR			0x00    /* PWM Control Register */
 #define MX3_PWMSR			0x04    /* PWM Status Register */
 #define MX3_PWMSAR			0x0C    /* PWM Sample Register */
 #define MX3_PWMPR			0x10    /* PWM Period Register */
+#define MX3_PWMCNR			0x14    /* PWM Counter Register */
 
 #define MX3_PWMCR_FWM			GENMASK(27, 26)
 #define MX3_PWMCR_STOPEN		BIT(25)
@@ -91,6 +93,7 @@ struct pwm_imx27_chip {
 	 * value to return in that case.
 	 */
 	unsigned int duty_cycle;
+	spinlock_t lock;
 };
 
 #define to_pwm_imx27_chip(chip)	container_of(chip, struct pwm_imx27_chip, chip)
@@ -203,10 +206,10 @@ static void pwm_imx27_wait_fifo_slot(struct pwm_chip *chip,
 
 	sr = readl(imx->mmio_base + MX3_PWMSR);
 	fifoav = FIELD_GET(MX3_PWMSR_FIFOAV, sr);
-	if (fifoav == MX3_PWMSR_FIFOAV_4WORDS) {
+	if (fifoav >= MX3_PWMSR_FIFOAV_3WORDS) {
 		period_ms = DIV_ROUND_UP_ULL(pwm_get_period(pwm),
 					 NSEC_PER_MSEC);
-		msleep(period_ms);
+		msleep(period_ms * (fifoav - 2));
 
 		sr = readl(imx->mmio_base + MX3_PWMSR);
 		if (fifoav == FIELD_GET(MX3_PWMSR_FIFOAV, sr))
@@ -217,13 +220,15 @@ static void pwm_imx27_wait_fifo_slot(struct pwm_chip *chip,
 static int pwm_imx27_apply(struct pwm_chip *chip, struct pwm_device *pwm,
 			   const struct pwm_state *state)
 {
-	unsigned long period_cycles, duty_cycles, prescale;
+	unsigned long period_cycles, duty_cycles, prescale, counter_check, flags;
 	struct pwm_imx27_chip *imx = to_pwm_imx27_chip(chip);
+	void __iomem *reg_sar = imx->mmio_base + MX3_PWMSAR;
+	__force u32 sar_last, sar_current;
 	struct pwm_state cstate;
 	unsigned long long c;
 	unsigned long long clkrate;
 	int ret;
-	u32 cr;
+	u32 cr, timeout = 1000;
 
 	pwm_get_state(pwm, &cstate);
 
@@ -264,7 +269,57 @@ static int pwm_imx27_apply(struct pwm_chip *chip, struct pwm_device *pwm,
 		pwm_imx27_sw_reset(chip);
 	}
 
-	writel(duty_cycles, imx->mmio_base + MX3_PWMSAR);
+	/*
+	 * This is a limited workaround. When the SAR FIFO is empty, the new
+	 * write value will be directly applied to SAR even the current period
+	 * is not over.
+	 * If the new SAR value is less than the old one, and the counter is
+	 * greater than the new SAR value, the current period will not filp
+	 * the level. This will result in a pulse with a duty cycle of 100%.
+	 * So, writing the current value of the SAR to SAR here before updating
+	 * the new SAR value can avoid this issue.
+	 *
+	 * Add a spin lock and turn off the interrupt to ensure that the
+	 * real-time performance can be guaranteed as much as possible when
+	 * operating the following operations.
+	 *
+	 * 1. Add a threshold of 1.5us. If the time T between the read current
+	 * count value CNR and the end of the cycle is less than 1.5us, wait
+	 * for T to be longer than 1.5us before updating the SAR register.
+	 * This is to avoid the situation that when the first SAR is written,
+	 * the current cycle just ends and the SAR FIFO that just be written
+	 * is emptied again.
+	 *
+	 * 2. Use __raw_writel() to minimize the interval between two writes to
+	 * the SAR register to increase the fastest pwm frequency supported.
+	 *
+	 * When the PWM period is longer than 2us(or <500KHz), this workaround
+	 * can solve this problem.
+	 */
+	if (duty_cycles < imx->duty_cycle) {
+		c = clkrate * 1500;
+		do_div(c, NSEC_PER_SEC);
+		counter_check = c;
+		sar_last = (__force u32) cpu_to_le32(imx->duty_cycle);
+		sar_current = (__force u32) cpu_to_le32(duty_cycles);
+
+		spin_lock_irqsave(&imx->lock, flags);
+		if (state->period >= 2000) {
+			while ((period_cycles -
+				readl_relaxed(imx->mmio_base + MX3_PWMCNR))
+				< counter_check) {
+				if (!--timeout)
+					break;
+			};
+		}
+		if (!(MX3_PWMSR_FIFOAV &
+		      readl_relaxed(imx->mmio_base + MX3_PWMSR)))
+			__raw_writel(sar_last, reg_sar);
+		__raw_writel(sar_current, reg_sar);
+		spin_unlock_irqrestore(&imx->lock, flags);
+	} else
+		writel(duty_cycles, imx->mmio_base + MX3_PWMSAR);
+
 	writel(period_cycles, imx->mmio_base + MX3_PWMPR);
 
 	/*
@@ -324,6 +379,8 @@ static int pwm_imx27_probe(struct platform_device *pdev)
 		return dev_err_probe(&pdev->dev, PTR_ERR(imx->clk_per),
 				     "failed to get peripheral clock\n");
 
+	spin_lock_init(&imx->lock);
+	imx->duty_cycle = 0;
 	imx->chip.ops = &pwm_imx27_ops;
 	imx->chip.dev = &pdev->dev;
 	imx->chip.npwm = 1;
Signature · 1 line
2.25.1
#3 lore raw

Hi Pratik,

Am 03.01.24 um 07:34 schrieb [email protected]:

Quoted 4 lines

From: Clark Wang <[email protected]>

This fixes the pwm output bug when decrease the duty cycle. This is a limited workaround for the PWM IP issue TKT0577206.

this looks like a patch from the vendor tree.

Could you please provide a link to the origin or at least to the document which describes TKT0577206?

As a i.MX6ULL user i couldn't find this issue in the chip errata. So are you sure that every PWM IP handled by this driver is affected?

Quoted 6 lines

Root cause:
When the SAR FIFO is empty, the new write value will be directly applied to SAR even the current period is not over.
If the new SAR value is less than the old one, and the counter is greater than the new SAR value, the current period will not filp the

s/filp/flip/ ?

Quoted 49 lines

level. This will result in a pulse with a duty cycle of 100%.

Workaround:
Add an old value SAR write before updating the new duty cycle to SAR. This will keep the new value is always in a not empty fifo, and can be wait to update after a period finished.

Limitation:
This workaround can only solve this issue when the PWM period is longer than 2us(or <500KHz).

---
V1 -> V2: fix sparse warnings reported-by: kernel test robot <[email protected]>

            Closes: https://lore.kernel.org/oe-kbuild-all/[email protected]/
  drivers/pwm/pwm-imx27.c | 67 ++++++++++++++++++++++++++++++++++++++---
  1 file changed, 62 insertions(+), 5 deletions(-)
drivers/pwm/pwm-imx27.c +3 -0
index 7d9bc43f12b0..1e500a5bf564 100644
@@ -21,11 +21,13 @@
  #include <linux/platform_device.h>
  #include <linux/pwm.h>
  #include <linux/slab.h>
+#include <linux/spinlock.h>
 
  #define MX3_PWMCR			0x00    /* PWM Control Register */
  #define MX3_PWMSR			0x04    /* PWM Status Register */
  #define MX3_PWMSAR			0x0C    /* PWM Sample Register */
  #define MX3_PWMPR			0x10    /* PWM Period Register */
+#define MX3_PWMCNR			0x14    /* PWM Counter Register */
 
  #define MX3_PWMCR_FWM			GENMASK(27, 26)
  #define MX3_PWMCR_STOPEN		BIT(25)
@@ -91,6 +93,7 @@ struct pwm_imx27_chip {
  	 * value to return in that case.
  	 */
  	unsigned int duty_cycle;
+	spinlock_t lock;
  };
 
  #define to_pwm_imx27_chip(chip)	container_of(chip, struct pwm_imx27_chip, chip)

drivers/pwm/pwm-imx27.c static void pwm_imx27_wait_fifo_slot(struct pwm_chip *chip, · line 212

Quoted 9 lines
drivers/pwm/pwm-imx27.c +2 -2
@@ -203,10 +206,10 @@ static void pwm_imx27_wait_fifo_slot(struct pwm_chip *chip,
 
  	sr = readl(imx->mmio_base + MX3_PWMSR);
  	fifoav = FIELD_GET(MX3_PWMSR_FIFOAV, sr);
-	if (fifoav == MX3_PWMSR_FIFOAV_4WORDS) {
+	if (fifoav >= MX3_PWMSR_FIFOAV_3WORDS) {
  		period_ms = DIV_ROUND_UP_ULL(pwm_get_period(pwm),
  					 NSEC_PER_MSEC);
-		msleep(period_ms);
+		msleep(period_ms * (fifoav - 2));

This touches a different workaround ("pwm: imx: Avoid sample FIFO overflow for i.MX PWM version2") without any explanation.

Quoted 22 lines
drivers/pwm/pwm-imx27.c +4 -2
  		sr = readl(imx->mmio_base + MX3_PWMSR);
  		if (fifoav == FIELD_GET(MX3_PWMSR_FIFOAV, sr))
@@ -217,13 +220,15 @@ static void pwm_imx27_wait_fifo_slot(struct pwm_chip *chip,
  static int pwm_imx27_apply(struct pwm_chip *chip, struct pwm_device *pwm,
  			   const struct pwm_state *state)
  {
-	unsigned long period_cycles, duty_cycles, prescale;
+	unsigned long period_cycles, duty_cycles, prescale, counter_check, flags;
  	struct pwm_imx27_chip *imx = to_pwm_imx27_chip(chip);
+	void __iomem *reg_sar = imx->mmio_base + MX3_PWMSAR;
+	__force u32 sar_last, sar_current;
  	struct pwm_state cstate;
  	unsigned long long c;
  	unsigned long long clkrate;
  	int ret;
-	u32 cr;
+	u32 cr, timeout = 1000;
 
  	pwm_get_state(pwm, &cstate);
 

drivers/pwm/pwm-imx27.c static int pwm_imx27_apply(struct pwm_chip *chip, struct pwm_device *pwm, · line 277

Quoted 10 lines
drivers/pwm/pwm-imx27.c +6 -1
@@ -264,7 +269,57 @@ static int pwm_imx27_apply(struct pwm_chip *chip, struct pwm_device *pwm,
  		pwm_imx27_sw_reset(chip);
  	}
 
-	writel(duty_cycles, imx->mmio_base + MX3_PWMSAR);
+	/*
+	 * This is a limited workaround. When the SAR FIFO is empty, the new
+	 * write value will be directly applied to SAR even the current period
+	 * is not over.
+	 * If the new SAR value is less than the old one, and the counter is
+	 * greater than the new SAR value, the current period will not filp

The same typo as in the commit message.

Quoted 35 lines
drivers/pwm/pwm-imx27.c +35 -0
+	 * the level. This will result in a pulse with a duty cycle of 100%.
+	 * So, writing the current value of the SAR to SAR here before updating
+	 * the new SAR value can avoid this issue.
+	 *
+	 * Add a spin lock and turn off the interrupt to ensure that the
+	 * real-time performance can be guaranteed as much as possible when
+	 * operating the following operations.
+	 *
+	 * 1. Add a threshold of 1.5us. If the time T between the read current
+	 * count value CNR and the end of the cycle is less than 1.5us, wait
+	 * for T to be longer than 1.5us before updating the SAR register.
+	 * This is to avoid the situation that when the first SAR is written,
+	 * the current cycle just ends and the SAR FIFO that just be written
+	 * is emptied again.
+	 *
+	 * 2. Use __raw_writel() to minimize the interval between two writes to
+	 * the SAR register to increase the fastest pwm frequency supported.
+	 *
+	 * When the PWM period is longer than 2us(or <500KHz), this workaround
+	 * can solve this problem.
+	 */
+	if (duty_cycles < imx->duty_cycle) {
+		c = clkrate * 1500;
+		do_div(c, NSEC_PER_SEC);
+		counter_check = c;
+		sar_last = (__force u32) cpu_to_le32(imx->duty_cycle);
+		sar_current = (__force u32) cpu_to_le32(duty_cycles);
+
+		spin_lock_irqsave(&imx->lock, flags);
+		if (state->period >= 2000) {
+			while ((period_cycles -
+				readl_relaxed(imx->mmio_base + MX3_PWMCNR))
+				< counter_check) {
+				if (!--timeout)
+					break;

drivers/pwm/pwm-imx27.c static int pwm_imx27_apply(struct pwm_chip *chip, struct pwm_device *pwm, · line 322

Quoted 10 lines
drivers/pwm/pwm-imx27.c +10 -0
+			};
+		}
+		if (!(MX3_PWMSR_FIFOAV &
+		      readl_relaxed(imx->mmio_base + MX3_PWMSR)))
+			__raw_writel(sar_last, reg_sar);
+		__raw_writel(sar_current, reg_sar);
+		spin_unlock_irqrestore(&imx->lock, flags);
+	} else
+		writel(duty_cycles, imx->mmio_base + MX3_PWMSAR);
+

This is hard to believe that checkpatch.pl is fine with this patch. Please use it before submission.

drivers/pwm/pwm-imx27.c static int pwm_imx27_probe(struct platform_device *pdev) · line 383

Quoted 9 lines
drivers/pwm/pwm-imx27.c +2 -0
  	writel(period_cycles, imx->mmio_base + MX3_PWMPR);
 
  	/*
@@ -324,6 +379,8 @@ static int pwm_imx27_probe(struct platform_device *pdev)
  		return dev_err_probe(&pdev->dev, PTR_ERR(imx->clk_per),
  				     "failed to get peripheral clock\n");
 
+	spin_lock_init(&imx->lock);
+	imx->duty_cycle = 0;

This line looks unrelated and unnecessary.

Best regards

Quoted 3 lines
drivers/pwm/pwm-imx27.c +0 -0
  	imx->chip.ops = &pwm_imx27_ops;
  	imx->chip.dev = &pdev->dev;
  	imx->chip.npwm = 1;
#4 lore raw
In reply to [email protected]

Hi Stefan,

Thanks for your review.
Please see my reply below inline.

Quoted 5 lines
Quoted 4 lines

From: Clark Wang <[email protected]>

This fixes the pwm output bug when decrease the duty cycle. This is a limited workaround for the PWM IP issue TKT0577206.

this looks like a patch from the vendor tree.

[Pratik]: Yes, this is the patch from NXP. Please see original link of the patch https://github.com/nxp-imx/linux-imx/commit/16181cc4eee61d87cbaba0e5a479990507816317

Quoted 2 lines

Could you please provide a link to the origin or at least to the document which describes TKT0577206?

[Pratik]: Please refer i.MX8MN errata #ERR051198 in https://www.nxp.com/docs/en/errata/IMX8MN_0N14Y.pdf.

Quoted 2 lines

As a i.MX6ULL user i couldn't find this issue in the chip errata. So are you sure that every PWM IP handled by this driver is affected?

[Pratik]: Yes, looks like this issue is on all platforms which uses this PWM IP.

Quoted 56 lines
Quoted 5 lines

Root cause:
When the SAR FIFO is empty, the new write value will be directly applied to SAR even the current period is not over.
If the new SAR value is less than the old one, and the counter is greater than the new SAR value, the current period will not filp the

s/filp/flip/ ?

Quoted 50 lines

level. This will result in a pulse with a duty cycle of 100%.

Workaround:
Add an old value SAR write before updating the new duty cycle to SAR. This will keep the new value is always in a not empty fifo, and can be wait to update after a period finished.

Limitation:
This workaround can only solve this issue when the PWM period is longer than 2us(or <500KHz).

---
V1 -> V2: fix sparse warnings reported-by: kernel test robot <[email protected]>

            Closes: https://lore.kernel.org/oe-kbuild-all/[email protected]/
  drivers/pwm/pwm-imx27.c | 67 ++++++++++++++++++++++++++++++++++++++---
  1 file changed, 62 insertions(+), 5 deletions(-)
drivers/pwm/pwm-imx27.c +3 -0
index 7d9bc43f12b0..1e500a5bf564 100644
@@ -21,11 +21,13 @@
  #include <linux/platform_device.h>
  #include <linux/pwm.h>
  #include <linux/slab.h>
+#include <linux/spinlock.h>
 
  #define MX3_PWMCR			0x00    /* PWM Control Register */
  #define MX3_PWMSR			0x04    /* PWM Status Register */
  #define MX3_PWMSAR			0x0C    /* PWM Sample Register */
  #define MX3_PWMPR			0x10    /* PWM Period Register */
+#define MX3_PWMCNR			0x14    /* PWM Counter Register */
 
  #define MX3_PWMCR_FWM			GENMASK(27, 26)
  #define MX3_PWMCR_STOPEN		BIT(25)
@@ -91,6 +93,7 @@ struct pwm_imx27_chip {
  	 * value to return in that case.
  	 */
  	unsigned int duty_cycle;
+	spinlock_t lock;
  };
 
  #define to_pwm_imx27_chip(chip)	container_of(chip, struct pwm_imx27_chip, chip)
@@ -203,10 +206,10 @@ static void pwm_imx27_wait_fifo_slot(struct pwm_chip *chip,
 
Quoted 10 lines

drivers/pwm/pwm-imx27.c static void pwm_imx27_wait_fifo_slot(struct pwm_chip *chip, · line 212

Quoted 8 lines
drivers/pwm/pwm-imx27.c +2 -2
  	sr = readl(imx->mmio_base + MX3_PWMSR);
  	fifoav = FIELD_GET(MX3_PWMSR_FIFOAV, sr);
-	if (fifoav == MX3_PWMSR_FIFOAV_4WORDS) {
+	if (fifoav >= MX3_PWMSR_FIFOAV_3WORDS) {
  		period_ms = DIV_ROUND_UP_ULL(pwm_get_period(pwm),
  					 NSEC_PER_MSEC);
-		msleep(period_ms);
+		msleep(period_ms * (fifoav - 2));

This touches a different workaround ("pwm: imx: Avoid sample FIFO overflow for i.MX PWM version2") without any explanation.

[Pratik]: Sure, I will look into this. Thanks!

Quoted 72 lines
Quoted 22 lines
drivers/pwm/pwm-imx27.c +4 -2
  		sr = readl(imx->mmio_base + MX3_PWMSR);
  		if (fifoav == FIELD_GET(MX3_PWMSR_FIFOAV, sr))
@@ -217,13 +220,15 @@ static void pwm_imx27_wait_fifo_slot(struct pwm_chip *chip,
  static int pwm_imx27_apply(struct pwm_chip *chip, struct pwm_device *pwm,
  			   const struct pwm_state *state)
  {
-	unsigned long period_cycles, duty_cycles, prescale;
+	unsigned long period_cycles, duty_cycles, prescale, counter_check, flags;
  	struct pwm_imx27_chip *imx = to_pwm_imx27_chip(chip);
+	void __iomem *reg_sar = imx->mmio_base + MX3_PWMSAR;
+	__force u32 sar_last, sar_current;
  	struct pwm_state cstate;
  	unsigned long long c;
  	unsigned long long clkrate;
  	int ret;
-	u32 cr;
+	u32 cr, timeout = 1000;
 
  	pwm_get_state(pwm, &cstate);
 

drivers/pwm/pwm-imx27.c static int pwm_imx27_apply(struct pwm_chip *chip, struct pwm_device *pwm, · line 277

Quoted 10 lines
drivers/pwm/pwm-imx27.c +6 -1
@@ -264,7 +269,57 @@ static int pwm_imx27_apply(struct pwm_chip *chip, struct pwm_device *pwm,
  		pwm_imx27_sw_reset(chip);
  	}
 
-	writel(duty_cycles, imx->mmio_base + MX3_PWMSAR);
+	/*
+	 * This is a limited workaround. When the SAR FIFO is empty, the new
+	 * write value will be directly applied to SAR even the current period
+	 * is not over.
+	 * If the new SAR value is less than the old one, and the counter is
+	 * greater than the new SAR value, the current period will not filp

The same typo as in the commit message.

Quoted 39 lines
drivers/pwm/pwm-imx27.c +39 -0
+	 * the level. This will result in a pulse with a duty cycle of 100%.
+	 * So, writing the current value of the SAR to SAR here before updating
+	 * the new SAR value can avoid this issue.
+	 *
+	 * Add a spin lock and turn off the interrupt to ensure that the
+	 * real-time performance can be guaranteed as much as possible when
+	 * operating the following operations.
+	 *
+	 * 1. Add a threshold of 1.5us. If the time T between the read current
+	 * count value CNR and the end of the cycle is less than 1.5us, wait
+	 * for T to be longer than 1.5us before updating the SAR register.
+	 * This is to avoid the situation that when the first SAR is written,
+	 * the current cycle just ends and the SAR FIFO that just be written
+	 * is emptied again.
+	 *
+	 * 2. Use __raw_writel() to minimize the interval between two writes to
+	 * the SAR register to increase the fastest pwm frequency supported.
+	 *
+	 * When the PWM period is longer than 2us(or <500KHz), this workaround
+	 * can solve this problem.
+	 */
+	if (duty_cycles < imx->duty_cycle) {
+		c = clkrate * 1500;
+		do_div(c, NSEC_PER_SEC);
+		counter_check = c;
+		sar_last = (__force u32) cpu_to_le32(imx->duty_cycle);
+		sar_current = (__force u32) cpu_to_le32(duty_cycles);
+
+		spin_lock_irqsave(&imx->lock, flags);
+		if (state->period >= 2000) {
+			while ((period_cycles -
+				readl_relaxed(imx->mmio_base + MX3_PWMCNR))
+				< counter_check) {
+				if (!--timeout)
+					break;
+			};
+		}
+		if (!(MX3_PWMSR_FIFOAV &
+		      readl_relaxed(imx->mmio_base + MX3_PWMSR)))
Quoted 8 lines

drivers/pwm/pwm-imx27.c static int pwm_imx27_apply(struct pwm_chip *chip, struct pwm_device *pwm, · line 322

Quoted 6 lines
drivers/pwm/pwm-imx27.c +6 -0
+			__raw_writel(sar_last, reg_sar);
+		__raw_writel(sar_current, reg_sar);
+		spin_unlock_irqrestore(&imx->lock, flags);
+	} else
+		writel(duty_cycles, imx->mmio_base + MX3_PWMSAR);
+

This is hard to believe that checkpatch.pl is fine with this patch. Please use it before submission.

[Pratik]: I used the checkpatch.pl in this patch and that runs without any warnings/errors!

Quoted 10 lines

drivers/pwm/pwm-imx27.c static int pwm_imx27_probe(struct platform_device *pdev) · line 383

Quoted 9 lines
drivers/pwm/pwm-imx27.c +2 -0
  	writel(period_cycles, imx->mmio_base + MX3_PWMPR);
 
  	/*
@@ -324,6 +379,8 @@ static int pwm_imx27_probe(struct platform_device *pdev)
  		return dev_err_probe(&pdev->dev, PTR_ERR(imx->clk_per),
  				     "failed to get peripheral clock\n");
 
+	spin_lock_init(&imx->lock);
+	imx->duty_cycle = 0;

This line looks unrelated and unnecessary.

[Pratik]: Right. I will remove this line in next patch version.

Quoted 4 lines

Best regards

Quoted 3 lines
drivers/pwm/pwm-imx27.c +0 -0
  	imx->chip.ops = &pwm_imx27_ops;
  	imx->chip.dev = &pdev->dev;
  	imx->chip.npwm = 1;
#5 lore raw

Hi Pratik,

Am 04.02.24 um 07:36 schrieb [email protected]:

Quoted 7 lines

Hi Stefan,

Thanks for your review.
Please see my reply below inline.

Quoted 2 lines
Quoted 2 lines

From: Clark Wang <[email protected]>

Quoted 8 lines
Quoted 3 lines
Quoted 2 lines

This fixes the pwm output bug when decrease the duty cycle. This is a limited workaround for the PWM IP issue TKT0577206.

this looks like a patch from the vendor tree.

[Pratik]: Yes, this is the patch from NXP. Please see original link of the patch https://github.com/nxp-imx/linux-imx/commit/16181cc4eee61d87cbaba0e5a479990507816317

Quoted 2 lines

Could you please provide a link to the origin or at least to the document which describes TKT0577206?

[Pratik]: Please refer i.MX8MN errata #ERR051198 in https://www.nxp.com/docs/en/errata/IMX8MN_0N14Y.pdf.

Thanks, i think this ERR... reference is better than TKT... because it's links to the errata documents and other Freescale/NXP drivers use them too. So having this code in a comment would be great.

Quoted 151 lines
Quoted 3 lines

As a i.MX6ULL user i couldn't find this issue in the chip errata. So are you sure that every PWM IP handled by this driver is affected?

[Pratik]: Yes, looks like this issue is on all platforms which uses this PWM IP.

Quoted 56 lines
Quoted 5 lines

Root cause:
When the SAR FIFO is empty, the new write value will be directly applied to SAR even the current period is not over.
If the new SAR value is less than the old one, and the counter is greater than the new SAR value, the current period will not filp the

s/filp/flip/ ?

Quoted 50 lines

level. This will result in a pulse with a duty cycle of 100%.

Workaround:
Add an old value SAR write before updating the new duty cycle to SAR. This will keep the new value is always in a not empty fifo, and can be wait to update after a period finished.

Limitation:
This workaround can only solve this issue when the PWM period is longer than 2us(or <500KHz).

---
V1 -> V2: fix sparse warnings reported-by: kernel test robot <[email protected]>

             Closes: https://lore.kernel.org/oe-kbuild-all/[email protected]/
   drivers/pwm/pwm-imx27.c | 67 ++++++++++++++++++++++++++++++++++++++---
   1 file changed, 62 insertions(+), 5 deletions(-)
drivers/pwm/pwm-imx27.c +3 -0
index 7d9bc43f12b0..1e500a5bf564 100644
@@ -21,11 +21,13 @@
   #include <linux/platform_device.h>
   #include <linux/pwm.h>
   #include <linux/slab.h>
+#include <linux/spinlock.h>
 
   #define MX3_PWMCR			0x00    /* PWM Control Register */
   #define MX3_PWMSR			0x04    /* PWM Status Register */
   #define MX3_PWMSAR			0x0C    /* PWM Sample Register */
   #define MX3_PWMPR			0x10    /* PWM Period Register */
+#define MX3_PWMCNR			0x14    /* PWM Counter Register */
 
   #define MX3_PWMCR_FWM			GENMASK(27, 26)
   #define MX3_PWMCR_STOPEN		BIT(25)
@@ -91,6 +93,7 @@ struct pwm_imx27_chip {
   	 * value to return in that case.
   	 */
   	unsigned int duty_cycle;
+	spinlock_t lock;
   };
 
   #define to_pwm_imx27_chip(chip)	container_of(chip, struct pwm_imx27_chip, chip)
@@ -203,10 +206,10 @@ static void pwm_imx27_wait_fifo_slot(struct pwm_chip *chip,
 
Quoted 10 lines

drivers/pwm/pwm-imx27.c static void pwm_imx27_wait_fifo_slot(struct pwm_chip *chip, · line 212

Quoted 8 lines
drivers/pwm/pwm-imx27.c +2 -2
   	sr = readl(imx->mmio_base + MX3_PWMSR);
   	fifoav = FIELD_GET(MX3_PWMSR_FIFOAV, sr);
-	if (fifoav == MX3_PWMSR_FIFOAV_4WORDS) {
+	if (fifoav >= MX3_PWMSR_FIFOAV_3WORDS) {
   		period_ms = DIV_ROUND_UP_ULL(pwm_get_period(pwm),
   					 NSEC_PER_MSEC);
-		msleep(period_ms);
+		msleep(period_ms * (fifoav - 2));

This touches a different workaround ("pwm: imx: Avoid sample FIFO overflow for i.MX PWM version2") without any explanation.

[Pratik]: Sure, I will look into this. Thanks!

Quoted 71 lines
Quoted 21 lines
drivers/pwm/pwm-imx27.c +4 -2
   		sr = readl(imx->mmio_base + MX3_PWMSR);
   		if (fifoav == FIELD_GET(MX3_PWMSR_FIFOAV, sr))
@@ -217,13 +220,15 @@ static void pwm_imx27_wait_fifo_slot(struct pwm_chip *chip,
   static int pwm_imx27_apply(struct pwm_chip *chip, struct pwm_device *pwm,
   			   const struct pwm_state *state)
   {
-	unsigned long period_cycles, duty_cycles, prescale;
+	unsigned long period_cycles, duty_cycles, prescale, counter_check, flags;
   	struct pwm_imx27_chip *imx = to_pwm_imx27_chip(chip);
+	void __iomem *reg_sar = imx->mmio_base + MX3_PWMSAR;
+	__force u32 sar_last, sar_current;
   	struct pwm_state cstate;
   	unsigned long long c;
   	unsigned long long clkrate;
   	int ret;
-	u32 cr;
+	u32 cr, timeout = 1000;
 
   	pwm_get_state(pwm, &cstate);
 

drivers/pwm/pwm-imx27.c static int pwm_imx27_apply(struct pwm_chip *chip, struct pwm_device *pwm, · line 277

Quoted 10 lines
drivers/pwm/pwm-imx27.c +6 -1
@@ -264,7 +269,57 @@ static int pwm_imx27_apply(struct pwm_chip *chip, struct pwm_device *pwm,
   		pwm_imx27_sw_reset(chip);
   	}
 
-	writel(duty_cycles, imx->mmio_base + MX3_PWMSAR);
+	/*
+	 * This is a limited workaround. When the SAR FIFO is empty, the new
+	 * write value will be directly applied to SAR even the current period
+	 * is not over.
+	 * If the new SAR value is less than the old one, and the counter is
+	 * greater than the new SAR value, the current period will not filp

The same typo as in the commit message.

Quoted 39 lines
drivers/pwm/pwm-imx27.c +39 -0
+	 * the level. This will result in a pulse with a duty cycle of 100%.
+	 * So, writing the current value of the SAR to SAR here before updating
+	 * the new SAR value can avoid this issue.
+	 *
+	 * Add a spin lock and turn off the interrupt to ensure that the
+	 * real-time performance can be guaranteed as much as possible when
+	 * operating the following operations.
+	 *
+	 * 1. Add a threshold of 1.5us. If the time T between the read current
+	 * count value CNR and the end of the cycle is less than 1.5us, wait
+	 * for T to be longer than 1.5us before updating the SAR register.
+	 * This is to avoid the situation that when the first SAR is written,
+	 * the current cycle just ends and the SAR FIFO that just be written
+	 * is emptied again.
+	 *
+	 * 2. Use __raw_writel() to minimize the interval between two writes to
+	 * the SAR register to increase the fastest pwm frequency supported.
+	 *
+	 * When the PWM period is longer than 2us(or <500KHz), this workaround
+	 * can solve this problem.
+	 */
+	if (duty_cycles < imx->duty_cycle) {
+		c = clkrate * 1500;
+		do_div(c, NSEC_PER_SEC);
+		counter_check = c;
+		sar_last = (__force u32) cpu_to_le32(imx->duty_cycle);
+		sar_current = (__force u32) cpu_to_le32(duty_cycles);
+
+		spin_lock_irqsave(&imx->lock, flags);
+		if (state->period >= 2000) {
+			while ((period_cycles -
+				readl_relaxed(imx->mmio_base + MX3_PWMCNR))
+				< counter_check) {
+				if (!--timeout)
+					break;
+			};
+		}
+		if (!(MX3_PWMSR_FIFOAV &
+		      readl_relaxed(imx->mmio_base + MX3_PWMSR)))
Quoted 8 lines

drivers/pwm/pwm-imx27.c static int pwm_imx27_apply(struct pwm_chip *chip, struct pwm_device *pwm, · line 322

Quoted 6 lines
drivers/pwm/pwm-imx27.c +6 -0
+			__raw_writel(sar_last, reg_sar);
+		__raw_writel(sar_current, reg_sar);
+		spin_unlock_irqrestore(&imx->lock, flags);
+	} else
+		writel(duty_cycles, imx->mmio_base + MX3_PWMSAR);
+

This is hard to believe that checkpatch.pl is fine with this patch. Please use it before submission.

Quoted 1 line

[Pratik]: I used the checkpatch.pl in this patch and that runs without any warnings/errors!

Okay, AFAIR the coding style suggests braces for the else case.

Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
drivers/pwm/pwm-imx27.c +0 -0
   	writel(period_cycles, imx->mmio_base + MX3_PWMPR);
 
   	/*
@@ -324,6 +379,8 @@ static int pwm_imx27_probe(struct platform_device *pdev)
   		return dev_err_probe(&pdev->dev, PTR_ERR(imx->clk_per),
   				     "failed to get peripheral clock\n");
 
Quoted 4 lines
Quoted 3 lines

drivers/pwm/pwm-imx27.c static int pwm_imx27_probe(struct platform_device *pdev) · line 383

Quoted 2 lines
drivers/pwm/pwm-imx27.c +2 -0
+	spin_lock_init(&imx->lock);
+	imx->duty_cycle = 0;

This line looks unrelated and unnecessary.

[Pratik]: Right. I will remove this line in next patch version.

Could you also please look at Uwe's comments [1]?

Thanks

[1] -
https://lore.kernel.org/all/[email protected]/

Quoted 5 lines
Quoted 5 lines

Best regards

Quoted 3 lines
drivers/pwm/pwm-imx27.c +0 -0
   	imx->chip.ops = &pwm_imx27_ops;
   	imx->chip.dev = &pdev->dev;
   	imx->chip.npwm = 1;
#6 lore raw
In reply to [email protected]

Hi Stefan,

Sorry for the abysmal delay.
Thanks for your review and suggestions.

Quoted 13 lines

Hi Pratik,

Am 04.02.24 um 07:36 schrieb [email protected]:

Quoted 10 lines

Hi Stefan,

Thanks for your review.
Please see my reply below inline.

Quoted 5 lines
Quoted 4 lines

From: Clark Wang <[email protected]>

This fixes the pwm output bug when decrease the duty cycle. This is a limited workaround for the PWM IP issue TKT0577206.

this looks like a patch from the vendor tree.

Quoted 8 lines
Quoted 5 lines

[Pratik]: Yes, this is the patch from NXP. Please see original link of the patch https://github.com/nxp-imx/linux-imx/commit/16181cc4eee61d87cbaba0e5a479990507816317

Quoted 2 lines

Could you please provide a link to the origin or at least to the document which describes TKT0577206?

[Pratik]: Please refer i.MX8MN errata #ERR051198 in https://www.nxp.com/docs/en/errata/IMX8MN_0N14Y.pdf.

Thanks, i think this ERR... reference is better than TKT... because it's links to the errata documents and other Freescale/NXP drivers use them too. So having this code in a comment would be great.

Sure, I will mention this #ERR051198 code in commit message.

Quoted 164 lines
Quoted 151 lines
Quoted 3 lines

As a i.MX6ULL user i couldn't find this issue in the chip errata. So are you sure that every PWM IP handled by this driver is affected?

[Pratik]: Yes, looks like this issue is on all platforms which uses this PWM IP.

Quoted 56 lines
Quoted 5 lines

Root cause:
When the SAR FIFO is empty, the new write value will be directly applied to SAR even the current period is not over.
If the new SAR value is less than the old one, and the counter is greater than the new SAR value, the current period will not filp the

s/filp/flip/ ?

Quoted 50 lines

level. This will result in a pulse with a duty cycle of 100%.

Workaround:
Add an old value SAR write before updating the new duty cycle to SAR. This will keep the new value is always in a not empty fifo, and can be wait to update after a period finished.

Limitation:
This workaround can only solve this issue when the PWM period is longer than 2us(or <500KHz).

---
V1 -> V2: fix sparse warnings reported-by: kernel test robot <[email protected]>

             Closes: https://lore.kernel.org/oe-kbuild-all/[email protected]/
   drivers/pwm/pwm-imx27.c | 67 ++++++++++++++++++++++++++++++++++++++---
   1 file changed, 62 insertions(+), 5 deletions(-)
drivers/pwm/pwm-imx27.c +3 -0
index 7d9bc43f12b0..1e500a5bf564 100644
@@ -21,11 +21,13 @@
   #include <linux/platform_device.h>
   #include <linux/pwm.h>
   #include <linux/slab.h>
+#include <linux/spinlock.h>
 
   #define MX3_PWMCR			0x00    /* PWM Control Register */
   #define MX3_PWMSR			0x04    /* PWM Status Register */
   #define MX3_PWMSAR			0x0C    /* PWM Sample Register */
   #define MX3_PWMPR			0x10    /* PWM Period Register */
+#define MX3_PWMCNR			0x14    /* PWM Counter Register */
 
   #define MX3_PWMCR_FWM			GENMASK(27, 26)
   #define MX3_PWMCR_STOPEN		BIT(25)
@@ -91,6 +93,7 @@ struct pwm_imx27_chip {
   	 * value to return in that case.
   	 */
   	unsigned int duty_cycle;
+	spinlock_t lock;
   };
 
   #define to_pwm_imx27_chip(chip)	container_of(chip, struct pwm_imx27_chip, chip)
@@ -203,10 +206,10 @@ static void pwm_imx27_wait_fifo_slot(struct pwm_chip *chip,
 
Quoted 10 lines

drivers/pwm/pwm-imx27.c static void pwm_imx27_wait_fifo_slot(struct pwm_chip *chip, · line 212

Quoted 8 lines
drivers/pwm/pwm-imx27.c +2 -2
   	sr = readl(imx->mmio_base + MX3_PWMSR);
   	fifoav = FIELD_GET(MX3_PWMSR_FIFOAV, sr);
-	if (fifoav == MX3_PWMSR_FIFOAV_4WORDS) {
+	if (fifoav >= MX3_PWMSR_FIFOAV_3WORDS) {
   		period_ms = DIV_ROUND_UP_ULL(pwm_get_period(pwm),
   					 NSEC_PER_MSEC);
-		msleep(period_ms);
+		msleep(period_ms * (fifoav - 2));

This touches a different workaround ("pwm: imx: Avoid sample FIFO overflow for i.MX PWM version2") without any explanation.

[Pratik]: Sure, I will look into this. Thanks!

Quoted 71 lines
Quoted 21 lines
drivers/pwm/pwm-imx27.c +4 -2
   		sr = readl(imx->mmio_base + MX3_PWMSR);
   		if (fifoav == FIELD_GET(MX3_PWMSR_FIFOAV, sr))
@@ -217,13 +220,15 @@ static void pwm_imx27_wait_fifo_slot(struct pwm_chip *chip,
   static int pwm_imx27_apply(struct pwm_chip *chip, struct pwm_device *pwm,
   			   const struct pwm_state *state)
   {
-	unsigned long period_cycles, duty_cycles, prescale;
+	unsigned long period_cycles, duty_cycles, prescale, counter_check, flags;
   	struct pwm_imx27_chip *imx = to_pwm_imx27_chip(chip);
+	void __iomem *reg_sar = imx->mmio_base + MX3_PWMSAR;
+	__force u32 sar_last, sar_current;
   	struct pwm_state cstate;
   	unsigned long long c;
   	unsigned long long clkrate;
   	int ret;
-	u32 cr;
+	u32 cr, timeout = 1000;
 
   	pwm_get_state(pwm, &cstate);
 

drivers/pwm/pwm-imx27.c static int pwm_imx27_apply(struct pwm_chip *chip, struct pwm_device *pwm, · line 277

Quoted 10 lines
drivers/pwm/pwm-imx27.c +6 -1
@@ -264,7 +269,57 @@ static int pwm_imx27_apply(struct pwm_chip *chip, struct pwm_device *pwm,
   		pwm_imx27_sw_reset(chip);
   	}
 
-	writel(duty_cycles, imx->mmio_base + MX3_PWMSAR);
+	/*
+	 * This is a limited workaround. When the SAR FIFO is empty, the new
+	 * write value will be directly applied to SAR even the current period
+	 * is not over.
+	 * If the new SAR value is less than the old one, and the counter is
+	 * greater than the new SAR value, the current period will not filp

The same typo as in the commit message.

Quoted 39 lines
drivers/pwm/pwm-imx27.c +39 -0
+	 * the level. This will result in a pulse with a duty cycle of 100%.
+	 * So, writing the current value of the SAR to SAR here before updating
+	 * the new SAR value can avoid this issue.
+	 *
+	 * Add a spin lock and turn off the interrupt to ensure that the
+	 * real-time performance can be guaranteed as much as possible when
+	 * operating the following operations.
+	 *
+	 * 1. Add a threshold of 1.5us. If the time T between the read current
+	 * count value CNR and the end of the cycle is less than 1.5us, wait
+	 * for T to be longer than 1.5us before updating the SAR register.
+	 * This is to avoid the situation that when the first SAR is written,
+	 * the current cycle just ends and the SAR FIFO that just be written
+	 * is emptied again.
+	 *
+	 * 2. Use __raw_writel() to minimize the interval between two writes to
+	 * the SAR register to increase the fastest pwm frequency supported.
+	 *
+	 * When the PWM period is longer than 2us(or <500KHz), this workaround
+	 * can solve this problem.
+	 */
+	if (duty_cycles < imx->duty_cycle) {
+		c = clkrate * 1500;
+		do_div(c, NSEC_PER_SEC);
+		counter_check = c;
+		sar_last = (__force u32) cpu_to_le32(imx->duty_cycle);
+		sar_current = (__force u32) cpu_to_le32(duty_cycles);
+
+		spin_lock_irqsave(&imx->lock, flags);
+		if (state->period >= 2000) {
+			while ((period_cycles -
+				readl_relaxed(imx->mmio_base + MX3_PWMCNR))
+				< counter_check) {
+				if (!--timeout)
+					break;
+			};
+		}
+		if (!(MX3_PWMSR_FIFOAV &
+		      readl_relaxed(imx->mmio_base + MX3_PWMSR)))
Quoted 8 lines

drivers/pwm/pwm-imx27.c static int pwm_imx27_apply(struct pwm_chip *chip, struct pwm_device *pwm, · line 322

Quoted 6 lines
drivers/pwm/pwm-imx27.c +6 -0
+			__raw_writel(sar_last, reg_sar);
+		__raw_writel(sar_current, reg_sar);
+		spin_unlock_irqrestore(&imx->lock, flags);
+	} else
+		writel(duty_cycles, imx->mmio_base + MX3_PWMSAR);
+

This is hard to believe that checkpatch.pl is fine with this patch. Please use it before submission.

Quoted 1 line

[Pratik]: I used the checkpatch.pl in this patch and that runs without any warnings/errors!

Okay, AFAIR the coding style suggests braces for the else case.

Quoted 11 lines
Quoted 11 lines

drivers/pwm/pwm-imx27.c static int pwm_imx27_probe(struct platform_device *pdev) · line 383

Quoted 10 lines
drivers/pwm/pwm-imx27.c +2 -0
   	writel(period_cycles, imx->mmio_base + MX3_PWMPR);
 
   	/*
@@ -324,6 +379,8 @@ static int pwm_imx27_probe(struct platform_device *pdev)
   		return dev_err_probe(&pdev->dev, PTR_ERR(imx->clk_per),
   				     "failed to get peripheral clock\n");
 
+	spin_lock_init(&imx->lock);
+	imx->duty_cycle = 0;

This line looks unrelated and unnecessary.

Quoted 7 lines
Quoted 1 line

[Pratik]: Right. I will remove this line in next patch version.

Could you also please look at Uwe's comments [1]?

Thanks

[1] -
https://lore.kernel.org/all/[email protected]/

Actually, I did not get much time to work on this. But, I will look into this now.

Quoted 5 lines
Quoted 5 lines
Quoted 5 lines

Best regards

Quoted 3 lines
drivers/pwm/pwm-imx27.c +0 -0
   	imx->chip.ops = &pwm_imx27_ops;
   	imx->chip.dev = &pdev->dev;
   	imx->chip.npwm = 1;

Thanks & Regards,
Pratik Manvar

#7 lore raw
In reply to [email protected]
Quoted 17 lines · On Fri, Dec 29, 2023 at 12:00:07PM +0530, [email protected] wrote:

From: Clark Wang <[email protected]>

This fixes the pwm output bug when decrease the duty cycle. This is a limited workaround for the PWM IP issue TKT0577206.

Root cause:
When the SAR FIFO is empty, the new write value will be directly applied to SAR even the current period is not over.
If the new SAR value is less than the old one, and the counter is greater than the new SAR value, the current period will not filp the level. This will result in a pulse with a duty cycle of 100%.

Workaround:
Add an old value SAR write before updating the new duty cycle to SAR. This will keep the new value is always in a not empty fifo, and can be wait to update after a period finished.

Quoted 8 lines

Limitation:
This workaround can only solve this issue when the PWM period is longer than 2us(or <500KHz).

You need to add your signed-off-by at the end when sending a patch, no matter if you are the author or not.

Francesco

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

#8 lore raw

PATCH v3 1/1 pwm: imx27: workaround of the pwm output bug

From: Clark Wang <[email protected]>

This fixes the pwm output bug when decrease the duty cycle. This is a limited workaround for the PWM IP issue TKT0577206.

Root cause:
When the SAR FIFO is empty, the new write value will be directly applied to SAR even the current period is not over.
If the new SAR value is less than the old one, and the counter is greater than the new SAR value, the current period will not filp the level. This will result in a pulse with a duty cycle of 100%.

Workaround:
Add an old value SAR write before updating the new duty cycle to SAR. This will keep the new value is always in a not empty fifo, and can be wait to update after a period finished.

Limitation:
This workaround can only solve this issue when the PWM period is longer than 2us(or <500KHz).

---
V1 -> V2: fix sparse warnings reported-by: kernel test robot <[email protected]>

           Closes: https://lore.kernel.org/oe-kbuild-all/[email protected]/

V2 -> V3: Add signed-off-by as suggested by Francesco Dolcini

 drivers/pwm/pwm-imx27.c | 67 ++++++++++++++++++++++++++++++++++++++---
 1 file changed, 62 insertions(+), 5 deletions(-)
drivers/pwm/pwm-imx27.c +62 -5
index 7d9bc43f12b0..1e500a5bf564 100644
@@ -21,11 +21,13 @@
 #include <linux/platform_device.h>
 #include <linux/pwm.h>
 #include <linux/slab.h>
+#include <linux/spinlock.h>
 
 #define MX3_PWMCR			0x00    /* PWM Control Register */
 #define MX3_PWMSR			0x04    /* PWM Status Register */
 #define MX3_PWMSAR			0x0C    /* PWM Sample Register */
 #define MX3_PWMPR			0x10    /* PWM Period Register */
+#define MX3_PWMCNR			0x14    /* PWM Counter Register */
 
 #define MX3_PWMCR_FWM			GENMASK(27, 26)
 #define MX3_PWMCR_STOPEN		BIT(25)
@@ -91,6 +93,7 @@ struct pwm_imx27_chip {
 	 * value to return in that case.
 	 */
 	unsigned int duty_cycle;
+	spinlock_t lock;
 };
 
 #define to_pwm_imx27_chip(chip)	container_of(chip, struct pwm_imx27_chip, chip)
@@ -203,10 +206,10 @@ static void pwm_imx27_wait_fifo_slot(struct pwm_chip *chip,
 
 	sr = readl(imx->mmio_base + MX3_PWMSR);
 	fifoav = FIELD_GET(MX3_PWMSR_FIFOAV, sr);
-	if (fifoav == MX3_PWMSR_FIFOAV_4WORDS) {
+	if (fifoav >= MX3_PWMSR_FIFOAV_3WORDS) {
 		period_ms = DIV_ROUND_UP_ULL(pwm_get_period(pwm),
 					 NSEC_PER_MSEC);
-		msleep(period_ms);
+		msleep(period_ms * (fifoav - 2));
 
 		sr = readl(imx->mmio_base + MX3_PWMSR);
 		if (fifoav == FIELD_GET(MX3_PWMSR_FIFOAV, sr))
@@ -217,13 +220,15 @@ static void pwm_imx27_wait_fifo_slot(struct pwm_chip *chip,
 static int pwm_imx27_apply(struct pwm_chip *chip, struct pwm_device *pwm,
 			   const struct pwm_state *state)
 {
-	unsigned long period_cycles, duty_cycles, prescale;
+	unsigned long period_cycles, duty_cycles, prescale, counter_check, flags;
 	struct pwm_imx27_chip *imx = to_pwm_imx27_chip(chip);
+	void __iomem *reg_sar = imx->mmio_base + MX3_PWMSAR;
+	__force u32 sar_last, sar_current;
 	struct pwm_state cstate;
 	unsigned long long c;
 	unsigned long long clkrate;
 	int ret;
-	u32 cr;
+	u32 cr, timeout = 1000;
 
 	pwm_get_state(pwm, &cstate);
 
@@ -264,7 +269,57 @@ static int pwm_imx27_apply(struct pwm_chip *chip, struct pwm_device *pwm,
 		pwm_imx27_sw_reset(chip);
 	}
 
-	writel(duty_cycles, imx->mmio_base + MX3_PWMSAR);
+	/*
+	 * This is a limited workaround. When the SAR FIFO is empty, the new
+	 * write value will be directly applied to SAR even the current period
+	 * is not over.
+	 * If the new SAR value is less than the old one, and the counter is
+	 * greater than the new SAR value, the current period will not filp
+	 * the level. This will result in a pulse with a duty cycle of 100%.
+	 * So, writing the current value of the SAR to SAR here before updating
+	 * the new SAR value can avoid this issue.
+	 *
+	 * Add a spin lock and turn off the interrupt to ensure that the
+	 * real-time performance can be guaranteed as much as possible when
+	 * operating the following operations.
+	 *
+	 * 1. Add a threshold of 1.5us. If the time T between the read current
+	 * count value CNR and the end of the cycle is less than 1.5us, wait
+	 * for T to be longer than 1.5us before updating the SAR register.
+	 * This is to avoid the situation that when the first SAR is written,
+	 * the current cycle just ends and the SAR FIFO that just be written
+	 * is emptied again.
+	 *
+	 * 2. Use __raw_writel() to minimize the interval between two writes to
+	 * the SAR register to increase the fastest pwm frequency supported.
+	 *
+	 * When the PWM period is longer than 2us(or <500KHz), this workaround
+	 * can solve this problem.
+	 */
+	if (duty_cycles < imx->duty_cycle) {
+		c = clkrate * 1500;
+		do_div(c, NSEC_PER_SEC);
+		counter_check = c;
+		sar_last = (__force u32) cpu_to_le32(imx->duty_cycle);
+		sar_current = (__force u32) cpu_to_le32(duty_cycles);
+
+		spin_lock_irqsave(&imx->lock, flags);
+		if (state->period >= 2000) {
+			while ((period_cycles -
+				readl_relaxed(imx->mmio_base + MX3_PWMCNR))
+				< counter_check) {
+				if (!--timeout)
+					break;
+			};
+		}
+		if (!(MX3_PWMSR_FIFOAV &
+		      readl_relaxed(imx->mmio_base + MX3_PWMSR)))
+			__raw_writel(sar_last, reg_sar);
+		__raw_writel(sar_current, reg_sar);
+		spin_unlock_irqrestore(&imx->lock, flags);
+	} else
+		writel(duty_cycles, imx->mmio_base + MX3_PWMSAR);
+
 	writel(period_cycles, imx->mmio_base + MX3_PWMPR);
 
 	/*
@@ -324,6 +379,8 @@ static int pwm_imx27_probe(struct platform_device *pdev)
 		return dev_err_probe(&pdev->dev, PTR_ERR(imx->clk_per),
 				     "failed to get peripheral clock\n");
 
+	spin_lock_init(&imx->lock);
+	imx->duty_cycle = 0;
 	imx->chip.ops = &pwm_imx27_ops;
 	imx->chip.dev = &pdev->dev;
 	imx->chip.npwm = 1;
Signature · 1 line
2.25.1
#9 lore raw

Hello Pratik,

Quoted 21 lines · On Wed, Jan 03, 2024 at 04:32:00PM +0530, [email protected] wrote:

From: Clark Wang <[email protected]>

This fixes the pwm output bug when decrease the duty cycle. This is a limited workaround for the PWM IP issue TKT0577206.

Root cause:
When the SAR FIFO is empty, the new write value will be directly applied to SAR even the current period is not over.
If the new SAR value is less than the old one, and the counter is greater than the new SAR value, the current period will not filp the level. This will result in a pulse with a duty cycle of 100%.

Workaround:
Add an old value SAR write before updating the new duty cycle to SAR. This will keep the new value is always in a not empty fifo, and can be wait to update after a period finished.

Limitation:
This workaround can only solve this issue when the PWM period is longer than 2us(or <500KHz).

Quoted 5 lines

A very similar patch was already send in 2021 [1], did it had review comments not addressed? Please have a look.

In general please refrain from sending a new patch version every other day, while every Linux kernel subsystem has different rules and a difference pace of development, in this specific case sending a v3 just adding your signed-off-by without allowing a little bit of time to wait for more feedback is just not sane.

[1] https://lore.kernel.org/all/?q=dfn%3Adrivers%2Fpwm%2Fpwm-imx27.c+AND+b%3A%22Clark+Wang%22

Francesco

#10 lore raw

Hi,

Am 03.01.24 um 13:20 schrieb Francesco Dolcini:

Quoted 32 lines

Hello Pratik,

Quoted 21 lines · On Wed, Jan 03, 2024 at 04:32:00PM +0530, [email protected] wrote:

From: Clark Wang <[email protected]>

This fixes the pwm output bug when decrease the duty cycle. This is a limited workaround for the PWM IP issue TKT0577206.

Root cause:
When the SAR FIFO is empty, the new write value will be directly applied to SAR even the current period is not over.
If the new SAR value is less than the old one, and the counter is greater than the new SAR value, the current period will not filp the level. This will result in a pulse with a duty cycle of 100%.

Workaround:
Add an old value SAR write before updating the new duty cycle to SAR. This will keep the new value is always in a not empty fifo, and can be wait to update after a period finished.

Limitation:
This workaround can only solve this issue when the PWM period is longer than 2us(or <500KHz).

Quoted 5 lines

A very similar patch was already send in 2021 [1], did it had review comments not addressed? Please have a look.

Quoted 7 lines

In general please refrain from sending a new patch version every other day, while every Linux kernel subsystem has different rules and a difference pace of development, in this specific case sending a v3 just adding your signed-off-by without allowing a little bit of time to wait for more feedback is just not sane.

[1] https://lore.kernel.org/all/?q=dfn%3Adrivers%2Fpwm%2Fpwm-imx27.c+AND+b%3A%22Clark+Wang%22

thank you, this is very helpful. Unfortunately i don't have the knowledge and resources to continue this work.

@Uwe It seems that you were able to reproduce this issue. Is it possible to trigger this via sysfs and some kind of script?

#11 lore raw

Hello Stefan,

Quoted 39 lines · Stefan Wahren

Am 03.01.24 um 13:20 schrieb Francesco Dolcini:

Quoted 38 lines

Hello Pratik,

Quoted 21 lines · On Wed, Jan 03, 2024 at 04:32:00PM +0530, [email protected] wrote:

From: Clark Wang <[email protected]>

This fixes the pwm output bug when decrease the duty cycle. This is a limited workaround for the PWM IP issue TKT0577206.

Root cause:
When the SAR FIFO is empty, the new write value will be directly applied to SAR even the current period is not over.
If the new SAR value is less than the old one, and the counter is greater than the new SAR value, the current period will not filp the level. This will result in a pulse with a duty cycle of 100%.

Workaround:
Add an old value SAR write before updating the new duty cycle to SAR. This will keep the new value is always in a not empty fifo, and can be wait to update after a period finished.

Limitation:
This workaround can only solve this issue when the PWM period is longer than 2us(or <500KHz).

Quoted 5 lines

A very similar patch was already send in 2021 [1], did it had review comments not addressed? Please have a look.

In general please refrain from sending a new patch version every other day, while every Linux kernel subsystem has different rules and a difference pace of development, in this specific case sending a v3 just adding your signed-off-by without allowing a little bit of time to wait for more feedback is just not sane.

Quoted 6 lines
Quoted 1 line

[1] https://lore.kernel.org/all/?q=dfn%3Adrivers%2Fpwm%2Fpwm-imx27.c+AND+b%3A%22Clark+Wang%22

thank you, this is very helpful. Unfortunately i don't have the knowledge and resources to continue this work.

@Uwe It seems that you were able to reproduce this issue. Is it possible to trigger this via sysfs and some kind of script?

When I read through the linked thread I was surprised to read that I could reproduce it. My best guess is that I did that using a long period and an LED connected to the PWM's output to make the effect easily visible. Something like: Configure for

	.duty_cycle = 1s, .period = 5s

and change that to

	.duty_cycle = 0s, .period = 5s

(e.g. using sysfs) when the output got high.

Best regards
Uwe

Signature · 2 lines
Pengutronix e.K.                           | Uwe Kleine-König            |
Industrial Linux Solutions                 | https://www.pengutronix.de/ |
#12 lore raw
In reply to [email protected]

Hello Francesco,

Sorry for the abysmal delay.
Thanks for your review and suggestions.

Quoted 30 lines

Hello Pratik,

Quoted 21 lines · On Wed, Jan 03, 2024 at 04:32:00PM +0530, [email protected] wrote:

From: Clark Wang <[email protected]>

This fixes the pwm output bug when decrease the duty cycle. This is a limited workaround for the PWM IP issue TKT0577206.

Root cause:
When the SAR FIFO is empty, the new write value will be directly applied to SAR even the current period is not over.
If the new SAR value is less than the old one, and the counter is greater than the new SAR value, the current period will not filp the level. This will result in a pulse with a duty cycle of 100%.

Workaround:
Add an old value SAR write before updating the new duty cycle to SAR. This will keep the new value is always in a not empty fifo, and can be wait to update after a period finished.

Limitation:
This workaround can only solve this issue when the PWM period is longer than 2us(or <500KHz).

Quoted 5 lines
Quoted 8 lines

A very similar patch was already send in 2021 [1], did it had review comments not addressed? Please have a look.

In general please refrain from sending a new patch version every other day, while every Linux kernel subsystem has different rules and a difference pace of development, in this specific case sending a v3 just adding your signed-off-by without allowing a little bit of time to wait for more feedback is just not sane.

Ok, I will keep this in mind. Thanks!

Quoted 2 lines

[1] https://lore.kernel.org/all/?q=dfn%3Adrivers%2Fpwm%2Fpwm-imx27.c+AND+b%3A%22Clark+Wang%22

Ok, I did not check this. I will look into this. Thanks!

Thanks & Regards,
Pratik Manvar

#13 lore raw
In reply to Francesco Dolcini
Quoted 22 lines · Francesco Dolcini
Quoted 21 lines · On Fri, Dec 29, 2023 at 12:00:07PM +0530, [email protected] wrote:

From: Clark Wang <[email protected]>

This fixes the pwm output bug when decrease the duty cycle. This is a limited workaround for the PWM IP issue TKT0577206.

Root cause:
When the SAR FIFO is empty, the new write value will be directly applied to SAR even the current period is not over.
If the new SAR value is less than the old one, and the counter is greater than the new SAR value, the current period will not filp the level. This will result in a pulse with a duty cycle of 100%.

Workaround:
Add an old value SAR write before updating the new duty cycle to SAR. This will keep the new value is always in a not empty fifo, and can be wait to update after a period finished.

Limitation:
This workaround can only solve this issue when the PWM period is longer than 2us(or <500KHz).

Quoted 7 lines
Quoted 4 lines

You need to add your signed-off-by at the end when sending a patch, no matter if you are the author or not.

FTR: This also applies to the v2 patch. I discarded both from the pwm patchwork.

Best regards
Uwe

Signature · 2 lines
Pengutronix e.K.                           | Uwe Kleine-König            |
Industrial Linux Solutions                 | https://www.pengutronix.de/ |