dt-bindings: nvmem: layouts: add U-Boot environment variables layout
Subsystems (4)
PATCH v3 1/6 dt-bindings: nvmem: layouts: add U-Boot environment variables layout
From: Rafał Miłecki <[email protected]>
U-Boot env data is a way of storing firmware variables. It's a format that can be used of top of various storage devices. Its binding should be an NVMEM layout instead of a standalone device.
This patch adds layout binding which allows using it on top of MTD NVMEM device as well as any other. At the same time it deprecates the old combined binding.
---
V2: Add "-layout" suffix to compatibles to avoid conflict
.../nvmem/layouts/u-boot,env-layout.yaml | 55 +++++++++++++++++++ .../devicetree/bindings/nvmem/u-boot,env.yaml | 6 ++ 2 files changed, 61 insertions(+) create mode 100644 Documentation/devicetree/bindings/nvmem/layouts/u-boot,env-layout.yaml
Documentation/devicetree/bindings/nvmem/layouts/u-boot,env-layout.yaml new file +55 -0
@@ -0,0 +1,55 @@ +# SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/nvmem/layouts/u-boot,env-layout.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NVMEM layout of U-Boot environment variables + +maintainers: + - Rafał Miłecki <[email protected]> + +description: + U-Boot uses environment variables to store device parameters and + configuration. They may be used for booting process, setup or keeping end user + info. + + Data is stored using U-Boot specific formats (variant specific header and NUL + separated key-value pairs). + +properties: + compatible: + oneOf: + - description: A standalone env data block + const: u-boot,env-layout + - description: Two redundant blocks with active one flagged + const: u-boot,env-redundant-bool-layout + - description: Two redundant blocks with active having higher counter + const: u-boot,env-redundant-count-layout + - description: Broadcom's variant with custom header + const: brcm,env-layout + +additionalProperties: false + +examples: + - | + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + reg = <0x0 0x40000>; + label = "u-boot"; + read-only; + }; + + partition@40000 { + reg = <0x40000 0x10000>; + label = "u-boot-env"; + + nvmem-layout { + compatible = "u-boot,env-layout"; + }; + }; + };
Documentation/devicetree/bindings/nvmem/u-boot,env.yaml +6 -0
@@ -26,9 +26,15 @@ description: | Variables can be defined as NVMEM device subnodes. + Introduction of NVMEM layouts exposed a limitation of this binding design. + Description of NVMEM data content should be separated from NVMEM devices. + Since the introduction of U-Boot env data layout this binding is deprecated. + maintainers: - Rafał Miłecki <[email protected]> +deprecated: true + properties: compatible: oneOf:
Signature · 1 line
2.35.3
PATCH v3 2/6 nvmem: core: add nvmem_dev_size() helper
From: Rafał Miłecki <[email protected]>
This is required by layouts that need to read whole NVMEM content. It's especially useful for NVMEM devices without hardcoded layout (like U-Boot environment data block).
--- drivers/nvmem/core.c | 13 +++++++++++++ include/linux/nvmem-consumer.h | 1 + 2 files changed, 14 insertions(+)
drivers/nvmem/core.c +13 -0
@@ -2163,6 +2163,19 @@ const char *nvmem_dev_name(struct nvmem_device *nvmem) }EXPORT_SYMBOL_GPL (nvmem_dev_name); +/** +* nvmem_dev_size() - Get the size of a given nvmem device. +* +* @nvmem: nvmem device. +* +* Return: size of the nvmem device. +*/ +size_t nvmem_dev_size (struct nvmem_device *nvmem) +{ +return nvmem->size; +} +EXPORT_SYMBOL_GPL (nvmem_dev_size); +static int __init nvmem_init (void ) {int ret;
include/linux/nvmem-consumer.h +1 -0
@@ -81,6 +81,7 @@ int nvmem_device_cell_write(struct nvmem_device *nvmem, struct nvmem_cell_info *info, void *buf);const char *nvmem_dev_name (struct nvmem_device *nvmem); +size_t nvmem_dev_size (struct nvmem_device *nvmem);void nvmem_add_cell_lookups (struct nvmem_cell_lookup *entries,size_t nentries);
Signature · 1 line
2.35.3
PATCH v3 3/6 nvmem: u-boot-env: use nvmem_add_one_cell() nvmem subsystem helper
In reply to Rafał MiłeckiFrom: Rafał Miłecki <[email protected]>
Simplify adding NVMEM cells.
---
V3: Split PATCH 3/3 into two
drivers/nvmem/u-boot-env.c | 55 +++++++++++++++----------------------- 1 file changed, 21 insertions(+), 34 deletions(-)
drivers/nvmem/u-boot-env.c +21 -34
@@ -23,13 +23,10 @@ enum u_boot_env_format {struct u_boot_env {struct device *dev; +struct nvmem_device *nvmem;enum u_boot_env_format format;struct mtd_info *mtd; - -/* Cells */ -struct nvmem_cell_info *cells; -int ncells; };struct u_boot_env_image_single {
@@ -94,43 +91,36 @@ static int u_boot_env_read_post_process_ethaddr(void *context, const char *id, istatic int u_boot_env_add_cells (struct u_boot_env *priv,uint8_t *buf,size_t data_offset,size_t data_len) { +struct nvmem_device *nvmem = priv->nvmem;struct device *dev = priv->dev;char *data = buf + data_offset;char *var, *value, *eq; -int idx; - - priv->ncells =0 ; -for (var = data; var < data + data_len && *var; var +=strlen (var) +1 ) - priv->ncells++; - - priv->cells =devm_kcalloc (dev, priv->ncells,sizeof (*priv->cells),GFP_KERNEL ); -if (!priv->cells) -return -ENOMEM ; -for (var = data, idx =0 ; +for (var = data; var < data + data_len && *var; - var = value +strlen (value) +1 , idx++) { + var = value +strlen (value) +1 ) { +struct nvmem_cell_info info = {}; + eq =strchr (var,'=' );if (!eq)break ; *eq ='\0' ; value = eq +1 ; - priv->cells[idx].name =devm_kstrdup (dev, var,GFP_KERNEL ); -if (!priv->cells[idx].name) + info.name =devm_kstrdup (dev, var,GFP_KERNEL ); +if (!info.name)return -ENOMEM ; - priv->cells[idx].offset = data_offset + value - data; - priv->cells[idx].bytes =strlen (value); - priv->cells[idx].np =of_get_child_by_name (dev->of_node, priv->cells[idx].name); + info.offset = data_offset + value - data; + info.bytes =strlen (value); + info.np =of_get_child_by_name (dev->of_node, info.name);if (!strcmp (var,"ethaddr" )) { - priv->cells[idx].raw_len =strlen (value); - priv->cells[idx].bytes =ETH_ALEN ; - priv->cells[idx].read_post_process = u_boot_env_read_post_process_ethaddr; + info.raw_len =strlen (value); + info.bytes =ETH_ALEN ; + info.read_post_process = u_boot_env_read_post_process_ethaddr; } - } -if (WARN_ON (idx != priv->ncells)) - priv->ncells = idx; +nvmem_add_one_cell (nvmem, &info); + }return 0 ; }
@@ -209,7 +199,6 @@ static int u_boot_env_probe(struct platform_device *pdev)struct device *dev = &pdev->dev;struct device_node *np = dev->of_node;struct u_boot_env *priv; -int err; priv =devm_kzalloc (dev,sizeof (*priv),GFP_KERNEL );if (!priv)
@@ -224,17 +213,15 @@ static int u_boot_env_probe(struct platform_device *pdev)return PTR_ERR (priv->mtd); } - err =u_boot_env_parse (priv); -if (err) -return err; - config.dev = dev; - config.cells = priv->cells; - config.ncells = priv->ncells; config.priv = priv; config.size = priv->mtd->size; -return PTR_ERR_OR_ZERO (devm_nvmem_register (dev, &config)); + priv->nvmem =devm_nvmem_register (dev, &config); +if (IS_ERR (priv->nvmem)) +return PTR_ERR (priv->nvmem); + +return u_boot_env_parse (priv); }static const struct of_device_id u_boot_env_of_match_table[] = {
Signature · 1 line
2.35.3
PATCH v3 4/6 nvmem: u-boot-env: use nvmem device helpers
In reply to Rafał MiłeckiFrom: Rafał Miłecki <[email protected]>
Use nvmem_dev_size() and nvmem_device_read() to make this driver less mtd dependent.
---
V2: Don't introduce memleak when handling nvmem_device_read() failures
V3: Split PATCH 3/3 into two
drivers/nvmem/u-boot-env.c | 23 +++++++++++++++-------- 1 file changed, 15 insertions(+), 8 deletions(-)
drivers/nvmem/u-boot-env.c +15 -8
@@ -127,27 +127,34 @@ static int u_boot_env_add_cells(struct u_boot_env *priv, uint8_t *buf,static int u_boot_env_parse (struct u_boot_env *priv) { +struct nvmem_device *nvmem = priv->nvmem;struct device *dev = priv->dev;size_t crc32_data_offset;size_t crc32_data_len;size_t crc32_offset;size_t data_offset;size_t data_len; +size_t dev_size;uint32_t crc32;uint32_t calc; -size_t bytes;uint8_t *buf; +int bytes;int err; - buf =kcalloc (1 , priv->mtd->size,GFP_KERNEL ); + dev_size =nvmem_dev_size (nvmem); + + buf =kcalloc (1 , dev_size,GFP_KERNEL );if (!buf) { err = -ENOMEM ; goto err_out; } - err =mtd_read (priv->mtd,0 , priv->mtd->size, &bytes, buf); -if ((err && !mtd_is_bitflip (err)) || bytes != priv->mtd->size) { -dev_err (dev,"Failed to read from mtd: %d\n" , err); + bytes =nvmem_device_read (nvmem,0 , dev_size, buf); +if (bytes <0 ) { + err = bytes; + goto err_kfree; + }else if (bytes != dev_size) { + err = -EIO ; goto err_kfree; }
@@ -169,8 +176,8 @@ static int u_boot_env_parse(struct u_boot_env *priv)break ; } crc32 =le32_to_cpu (*(__le32 *)(buf + crc32_offset)); - crc32_data_len = priv->mtd->size - crc32_data_offset; - data_len = priv->mtd->size - data_offset; + crc32_data_len = dev_size - crc32_data_offset; + data_len = dev_size - data_offset; calc =crc32 (~0 , buf + crc32_data_offset, crc32_data_len) ^ ~0L ;if (calc != crc32) {
@@ -179,7 +186,7 @@ static int u_boot_env_parse(struct u_boot_env *priv) goto err_kfree; } - buf[priv->mtd->size -1 ] ='\0' ; + buf[dev_size -1 ] ='\0' ; err =u_boot_env_add_cells (priv, buf, data_offset, data_len);if (err)dev_err (dev,"Failed to add cells: %d\n" , err);
Signature · 1 line
2.35.3
PATCH v3 5/6 nvmem: u-boot-env: improve coding style
In reply to Rafał MiłeckiFrom: Rafał Miłecki <[email protected]>
1. Prefer kzalloc() over kcalloc()
See memory-allocation.rst which says: "to be on the safe side it's best to use routines that set memory to zero, like kzalloc()"
2. Drop dev_err() for u_boot_env_add_cells() fail
It can fail only on -ENOMEM. We don't want to print error then.
3. Add extra "crc32_addr" variable
It makes code reading header's crc32 easier to understand / review.
---
V2: New patch with suggestions from Miquel
drivers/nvmem/u-boot-env.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-)
drivers/nvmem/u-boot-env.c +4 -4
@@ -132,6 +132,7 @@ static int u_boot_env_parse(struct u_boot_env *priv)size_t crc32_data_offset;size_t crc32_data_len;size_t crc32_offset; +__le32 *crc32_addr;size_t data_offset;size_t data_len;size_t dev_size;
@@ -143,7 +144,7 @@ static int u_boot_env_parse(struct u_boot_env *priv) dev_size =nvmem_dev_size (nvmem); - buf =kcalloc (1 , dev_size,GFP_KERNEL ); + buf =kzalloc (dev_size,GFP_KERNEL );if (!buf) { err = -ENOMEM ; goto err_out;
@@ -175,7 +176,8 @@ static int u_boot_env_parse(struct u_boot_env *priv) data_offset = offsetof(struct u_boot_env_image_broadcom , data);break ; } - crc32 =le32_to_cpu (*(__le32 *)(buf + crc32_offset)); + crc32_addr = (__le32 *)(buf + crc32_offset); + crc32 =le32_to_cpu (*crc32_addr); crc32_data_len = dev_size - crc32_data_offset; data_len = dev_size - data_offset;
@@ -188,8 +190,6 @@ static int u_boot_env_parse(struct u_boot_env *priv) buf[dev_size -1 ] ='\0' ; err =u_boot_env_add_cells (priv, buf, data_offset, data_len); -if (err) -dev_err (dev,"Failed to add cells: %d\n" , err); err_kfree:kfree (buf);
Signature · 1 line
2.35.3
PATCH v3 6/6 nvmem: layouts: add U-Boot env layout
In reply to Rafał MiłeckiFrom: Rafał Miłecki <[email protected]>
Move all generic (NVMEM devices independent) code from NVMEM device driver to NVMEM layout driver. Then add a simple NVMEM layout code on top of it.
Thanks to proper layout it's possible to support U-Boot env data stored on any kind of NVMEM device.
For backward compatibility with old DT bindings we need to keep old NVMEM device driver functional. To avoid code duplication export and reuse a parsing function.
---
V2: Support new compatibles & use device_get_match_data() helper
V3: Use imperative in commit body
IMPORTANT:
This is based on top of the:
[PATCH v6.8 1/2] nvmem: layouts: refactor .add_cells() callback arguments
MAINTAINERS | 1 + drivers/nvmem/Kconfig | 3 +- drivers/nvmem/layouts/Kconfig | 11 ++ drivers/nvmem/layouts/Makefile | 1 + drivers/nvmem/layouts/u-boot-env.c | 204 +++++++++++++++++++++++++++++ drivers/nvmem/layouts/u-boot-env.h | 15 +++ drivers/nvmem/u-boot-env.c | 158 +--------------------- 7 files changed, 235 insertions(+), 158 deletions(-) create mode 100644 drivers/nvmem/layouts/u-boot-env.c create mode 100644 drivers/nvmem/layouts/u-boot-env.h
MAINTAINERS +1 -0
@@ -22282,6 +22282,7 @@ U-BOOT ENVIRONMENT VARIABLES M: Rafał Miłecki <[email protected]> S: Maintained F: Documentation/devicetree/bindings/nvmem/u-boot,env.yaml +F: drivers/nvmem/layouts/u-boot-env.c F: drivers/nvmem/u-boot-env.c UACCE ACCELERATOR FRAMEWORK
drivers/nvmem/Kconfig +1 -2
@@ -363,8 +363,7 @@ config NVMEM_SUNXI_SID config NVMEM_U_BOOT_ENV tristate "U-Boot environment variables support" depends on OF && MTD - select CRC32 - select GENERIC_NET_UTILS + select NVMEM_LAYOUT_U_BOOT_ENV help U-Boot stores its setup as environment variables. This driver adds support for verifying & exporting such data. It also exposes variables
drivers/nvmem/layouts/Kconfig +11 -0
@@ -26,6 +26,17 @@ config NVMEM_LAYOUT_ONIE_TLV If unsure, say N. +config NVMEM_LAYOUT_U_BOOT_ENV + tristate "U-Boot environment variables layout" + select CRC32 + select GENERIC_NET_UTILS + help + U-Boot stores its setup as environment variables. This driver adds + support for verifying & exporting such data. It also exposes variables + as NVMEM cells so they can be referenced by other drivers. + + If unsure, say N. + endmenu endif
drivers/nvmem/layouts/Makefile +1 -0
@@ -5,3 +5,4 @@ obj-$(CONFIG_NVMEM_LAYOUT_SL28_VPD) += sl28vpd.o obj-$(CONFIG_NVMEM_LAYOUT_ONIE_TLV) += onie-tlv.o +obj-$(CONFIG_NVMEM_LAYOUT_U_BOOT_ENV) += u-boot-env.o
drivers/nvmem/layouts/u-boot-env.c new file +204 -0
204 lines not on this page · raw message
drivers/nvmem/layouts/u-boot-env.h new file +15 -0
@@ -0,0 +1,15 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +#ifndef _LINUX_NVMEM_LAYOUTS_U_BOOT_ENV_H +#define _LINUX_NVMEM_LAYOUTS_U_BOOT_ENV_H + +enum u_boot_env_format { +U_BOOT_FORMAT_SINGLE , +U_BOOT_FORMAT_REDUNDANT , +U_BOOT_FORMAT_BROADCOM , +}; + +int u_boot_env_parse (struct device *dev,struct nvmem_device *nvmem, +enum u_boot_env_format format); + +#endif /* ifndef _LINUX_NVMEM_LAYOUTS_U_BOOT_ENV_H */
drivers/nvmem/u-boot-env.c +2 -156
190 lines not on this page · raw message
Signature · 1 line
2.35.3
Re: [PATCH V3 6/6] nvmem: layouts: add U-Boot env layout
Quoted 15 lines · Rafał Miłecki
From: Rafał Miłecki <[email protected]>
Move all generic (NVMEM devices independent) code from NVMEM device driver to NVMEM layout driver. Then add a simple NVMEM layout code on top of it.
Thanks to proper layout it's possible to support U-Boot env data stored on any kind of NVMEM device.
For backward compatibility with old DT bindings we need to keep old NVMEM device driver functional. To avoid code duplication export and reuse a parsing function.
Signed-off-by Rafał Miłecki <[email protected]>Reviewed-by Miquel Raynal <[email protected]>
Quoted 7 lines
---
V2: Support new compatibles & usedevice_get_match_data()helper
V3: Use imperative in commit bodyIMPORTANT:
This is based on top of the:
[PATCH v6.8 1/2] nvmem: layouts: refactor .add_cells() callback arguments
I applied patches 2-5 in this series, I'll let you rebase the remaining two after addressing the issues discussed in patch 1.
thanks,
gre gk-h
Rob Herring
maintainerQuoted 9 lines · Rafał Miłecki
From: Rafał Miłecki <[email protected]>
U-Boot env data is a way of storing firmware variables. It's a format that can be used of top of various storage devices. Its binding should be an NVMEM layout instead of a standalone device.
This patch adds layout binding which allows using it on top of MTD NVMEM device as well as any other. At the same time it deprecates the old combined binding.
I don't understand the issue. From a DT perspective, there isn't. A partition is not a device, but is describing the layout of storage already.
Rob
Miquel Raynal
maintainerHello,
[email protected] wrote on Wed, 3 Jan 2024 17:11:29 -0700:
Quoted 7 lines · Rafał Miłecki
Quoted 6 lines
From: Rafał Miłecki <[email protected]>
U-Boot env data is a way of storing firmware variables. It's a format that can be used of top of various storage devices. Its binding should be an NVMEM layout instead of a standalone device.
Quoted 7 lines
Quoted 3 lines
This patch adds layout binding which allows using it on top of MTD NVMEM device as well as any other. At the same time it deprecates the old combined binding.
I don't understand the issue. From a DT perspective, there isn't. A partition is not a device, but is describing the layout of storage already.
Actually I think what Rafał wants to do goes in the right direction but I also understand from a binding perspective it may be a little confusing, even more if we consider "NVMEM" a Linux specific concept.
There is today a "u-boot env" NVMEM *device* description which almost sits at the same level as eg. an eeprom device. We cannot compare "an eeprom device" and "a u-boot environment" of course. But that's truly what is currently described.
* Current situation
Flash device -> U-Boot env layout -> NVMEM cells
* Improved situation
Any storage device -> NVMEM -> U-Boot env layout -> NVMEM cells
The latter is of course the most relevant description as we expect storage devices to expose a storage-agnostic interface (NVMEM in this case) which can then be parsed (by NVMEM layouts) in a storage agnostic way.
In the current case, the current U-Boot env binding tells people to declare the env layout on top of a flash device (only). The current description also expects a partition node which is typical to flash devices. Whereas what we should have described in the first place is a layout that applies on any kind of NVMEM device.
Bonus point: We've been working the last couple years on clarifying bindings, especially with mtd partitions (with the partitions{} container) and NVMEM layouts (with the nvmem-layout{} container). The switch proposed in this patch makes use of the latter, of course.
Thanks,
Miquèl
Quoted 44 lines · Miquel Raynal
[email protected] wrote on Wed, 3 Jan 2024 17:11:29 -0700:
Quoted 7 lines · Rafał Miłecki
Quoted 6 lines
From: Rafał Miłecki <[email protected]>
U-Boot env data is a way of storing firmware variables. It's a format that can be used of top of various storage devices. Its binding should be an NVMEM layout instead of a standalone device.
Quoted 7 lines
Quoted 3 lines
This patch adds layout binding which allows using it on top of MTD NVMEM device as well as any other. At the same time it deprecates the old combined binding.
I don't understand the issue. From a DT perspective, there isn't. A partition is not a device, but is describing the layout of storage already.
Actually I think what Rafał wants to do goes in the right direction but I also understand from a binding perspective it may be a little confusing, even more if we consider "NVMEM" a Linux specific concept.
There is today a "u-boot env" NVMEM *device* description which almost sits at the same level as eg. an eeprom device. We cannot compare "an eeprom device" and "a u-boot environment" of course. But that's truly what is currently described.
* Current situation
Flash device -> U-Boot env layout -> NVMEM cells* Improved situation
Any storage device -> NVMEM -> U-Boot env layout -> NVMEM cellsThe latter is of course the most relevant description as we expect storage devices to expose a storage-agnostic interface (NVMEM in this case) which can then be parsed (by NVMEM layouts) in a storage agnostic way.
In the current case, the current U-Boot env binding tells people to declare the env layout on top of a flash device (only). The current description also expects a partition node which is typical to flash devices. Whereas what we should have described in the first place is a layout that applies on any kind of NVMEM device.
Quoted 4 lines
Bonus point: We've been working the last couple years on clarifying bindings, especially with mtd partitions (with the partitions{} container) and NVMEM layouts (with the nvmem-layout{} container). The switch proposed in this patch makes use of the latter, of course.
Thanks Miquèl for filling bits I missed in commit description. Despite years in Linux/DT I still struggle with more complex designs documentation.
As per Rob's comment I think I see his point and a possible design confusion. If you look from a pure DT perspective then "partitions" and "nvmem-layout" serve a very similar purpose. They describe device's data content structure. For fixed structures we have very similar "fixed-partitions" and "fixed-cells".
If we were to design those bindings today I'm wondering if we couldn't have s/partitions/layout/ and s/nvmem-layout/layout/.
Rob: other than having different bindings for MTD vs. NVMEM layouts I think they overall design makes sense. A single device may have content structurized on more than 1 level:
1. You may have fixed layout at top level (multiple partitions)
2. Single partitions may have their own layouts (like U-Boot env data)
Maybe ideally above should look more like:
flash@0 {
compatible = "<flash-compatible>";
layout {
compatible = "fixed-layout";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
reg = <0x0 0x40000>;
label = "u-boot";
};
partition@40000 {
reg = <0x40000 0x10000>;
label = "u-boot-env";
layout {
compatible = "u-boot,env-layout";
};
};
partition@50000 {
reg = <0x50000 0x100000>;
label = "u-boot";
};
};
};but I can clearly see a use for nested "layout"s. As I said maybe we just shouldn't be so open in calling those MTD or NVMEM devices as that is kind of Linux specific.
I'm not sure if we should try renaming "nvmem-layout" to "layout" or "partitions" in similar way at this point.
Rob Herring
maintainerQuoted 21 lines · Rafał Miłecki
Quoted 20 lines · Miquel Raynal
[email protected] wrote on Wed, 3 Jan 2024 17:11:29 -0700:
Quoted 7 lines · Rafał Miłecki
Quoted 6 lines
From: Rafał Miłecki <[email protected]>
U-Boot env data is a way of storing firmware variables. It's a format that can be used of top of various storage devices. Its binding should be an NVMEM layout instead of a standalone device.
Quoted 7 lines
Quoted 3 lines
This patch adds layout binding which allows using it on top of MTD NVMEM device as well as any other. At the same time it deprecates the old combined binding.
I don't understand the issue. From a DT perspective, there isn't. A partition is not a device, but is describing the layout of storage already.
Actually I think what Rafał wants to do goes in the right direction but I also understand from a binding perspective it may be a little confusing, even more if we consider "NVMEM" a Linux specific concept.
Quoted 8 lines
Quoted 8 lines
There is today a "u-boot env" NVMEM *device* description which almost sits at the same level as eg. an eeprom device. We cannot compare "an eeprom device" and "a u-boot environment" of course. But that's truly what is currently described.
* Current situation
Flash device -> U-Boot env layout -> NVMEM cells
Isn't it?:
Flash device -> fixed-partitions -> U-Boot env layout -> NVMEM cells
Quoted 4 lines
Quoted 4 lines
* Improved situation
Any storage device -> NVMEM -> U-Boot env layout -> NVMEM cells
Why is this better? We don't need a container to say 'this is NVMEM stuff' or 'this is MTD stuff'. 'U-Boot env layout' can tell us 'this is NVMEM stuff' or whatever the kernel decides in the future.
Quoted 22 lines
Quoted 12 lines
The latter is of course the most relevant description as we expect storage devices to expose a storage-agnostic interface (NVMEM in this case) which can then be parsed (by NVMEM layouts) in a storage agnostic way.
In the current case, the current U-Boot env binding tells people to declare the env layout on top of a flash device (only). The current description also expects a partition node which is typical to flash devices. Whereas what we should have described in the first place is a layout that applies on any kind of NVMEM device.
Quoted 4 lines
Bonus point: We've been working the last couple years on clarifying bindings, especially with mtd partitions (with the partitions{} container) and NVMEM layouts (with the nvmem-layout{} container). The switch proposed in this patch makes use of the latter, of course.
Thanks Miquèl for filling bits I missed in commit description. Despite years in Linux/DT I still struggle with more complex designs documentation.
Quoted 8 lines
As per Rob's comment I think I see his point and a possible design confusion. If you look from a pure DT perspective then "partitions" and "nvmem-layout" serve a very similar purpose. They describe device's data content structure. For fixed structures we have very similar "fixed-partitions" and "fixed-cells".
If we were to design those bindings today I'm wondering if we couldn't have s/partitions/layout/ and s/nvmem-layout/layout/.
Why!? It is just a name, and we can't get rid of the old names. We don't need 2 names.
Quoted 5 lines
Rob: other than having different bindings for MTD vs. NVMEM layouts I think they overall design makes sense. A single device may have content structurized on more than 1 level:
1. You may have fixed layout at top level (multiple partitions)
2. Single partitions may have their own layouts (like U-Boot env data)
Sure. Partitions is for 1 and Layouts is for 2.
Quoted 7 lines
Maybe ideally above should look more like:
flash@0 { compatible = "<flash-compatible>"; layout { compatible = "fixed-layout";
Why does 'partitions' and 'fixed-partitions' not work here?
Quoted 24 lines
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
reg = <0x0 0x40000>;
label = "u-boot";
};
partition@40000 {
reg = <0x40000 0x10000>;
label = "u-boot-env";
layout {
compatible = "u-boot,env-layout";
};
};
partition@50000 {
reg = <0x50000 0x100000>;
label = "u-boot";
};
};
};Quoted 3 lines
but I can clearly see a use for nested "layout"s. As I said maybe we just shouldn't be so open in calling those MTD or NVMEM devices as that is kind of Linux specific.
The overall structure should be agnostic to the subsystem. Specific compatibles like 'u-boot,env' can be tied to a subsystem.
Maybe some things need to be both MTD and NVMEM. MTD to operate on the opague region and NVMEM to access the contents.
Quoted 2 lines
I'm not sure if we should try renaming "nvmem-layout" to "layout" or "partitions" in similar way at this point.
You can't rename. It's an ABI though maybe the whole "nvmem-layout" is new enough we can. It's looking like it was a mistake to accept any of this.
Rob
Miquel Raynal
maintainerHi Rob,
[email protected] wrote on Mon, 15 Jan 2024 11:09:03 -0600:
Quoted 36 lines · Rafał Miłecki
Quoted 21 lines · Miquel Raynal
Quoted 20 lines
[email protected] wrote on Wed, 3 Jan 2024 17:11:29 -0700:
Quoted 7 lines · Rafał Miłecki
Quoted 6 lines
From: Rafał Miłecki <[email protected]>
U-Boot env data is a way of storing firmware variables. It's a format that can be used of top of various storage devices. Its binding should be an NVMEM layout instead of a standalone device.
Quoted 7 lines
Quoted 3 lines
This patch adds layout binding which allows using it on top of MTD NVMEM device as well as any other. At the same time it deprecates the old combined binding.
I don't understand the issue. From a DT perspective, there isn't. A partition is not a device, but is describing the layout of storage already.
Actually I think what Rafał wants to do goes in the right direction but I also understand from a binding perspective it may be a little confusing, even more if we consider "NVMEM" a Linux specific concept.
Quoted 8 lines
Quoted 8 lines
There is today a "u-boot env" NVMEM *device* description which almost sits at the same level as eg. an eeprom device. We cannot compare "an eeprom device" and "a u-boot environment" of course. But that's truly what is currently described.
* Current situation
Flash device -> U-Boot env layout -> NVMEM cellsIsn't it?:
Flash device -> fixed-partitions -> U-Boot env layout -> NVMEM cells
Quoted 1 line
Quoted 1 line
Quoted 7 lines
Quoted 3 lines
Quoted 3 lines
* Improved situation
Any storage device -> NVMEM -> U-Boot env layout -> NVMEM cellsWhy is this better? We don't need a container to say 'this is NVMEM stuff' or 'this is MTD stuff'. 'U-Boot env layout' can tell us 'this is NVMEM stuff' or whatever the kernel decides in the future.
Yes, I also want the U-boot env layout to tell us "this is nvmem stuff". But that's not the case today. Today, it says "this is NVMEM stuff on top of mtd stuff". This was a mistake in the first place, but this compatible is heavily tight to mtd and cannot work on anything else. And correcting this is IMO the right direction.
Quoted 27 lines
Quoted 27 lines
Quoted 11 lines
The latter is of course the most relevant description as we expect storage devices to expose a storage-agnostic interface (NVMEM in this case) which can then be parsed (by NVMEM layouts) in a storage agnostic way.
In the current case, the current U-Boot env binding tells people to declare the env layout on top of a flash device (only). The current description also expects a partition node which is typical to flash devices. Whereas what we should have described in the first place is a layout that applies on any kind of NVMEM device.
Quoted 4 lines
Bonus point: We've been working the last couple years on clarifying bindings, especially with mtd partitions (with the partitions{} container) and NVMEM layouts (with the nvmem-layout{} container). The switch proposed in this patch makes use of the latter, of course.
Thanks Miquèl for filling bits I missed in commit description. Despite years in Linux/DT I still struggle with more complex designs documentation.
As per Rob's comment I think I see his point and a possible design confusion. If you look from a pure DT perspective then "partitions" and "nvmem-layout" serve a very similar purpose. They describe device's data content structure. For fixed structures we have very similar "fixed-partitions" and "fixed-cells".
Quoted 5 lines
Quoted 2 lines
If we were to design those bindings today I'm wondering if we couldn't have s/partitions/layout/ and s/nvmem-layout/layout/.
Why!? It is just a name, and we can't get rid of the old names. We don't need 2 names.
We need 2 names because we are not capturing the same concepts here?
Quoted 10 lines
Quoted 5 lines
Rob: other than having different bindings for MTD vs. NVMEM layouts I think they overall design makes sense. A single device may have content structurized on more than 1 level:
1. You may have fixed layout at top level (multiple partitions)
2. Single partitions may have their own layouts (like U-Boot env data)Sure. Partitions is for 1 and Layouts is for 2.
Quoted 2 lines
Maybe ideally above should look more like:
Quoted 7 lines
Quoted 5 lines
flash@0 { compatible = "<flash-compatible>"; layout { compatible = "fixed-layout";Why does 'partitions' and 'fixed-partitions' not work here?
They do, and that's actually what we use. This example just illustrates another proposal from Rafal. No panic :)
Quoted 36 lines
Quoted 25 lines
#address-cells = <1>; #size-cells = <1>; partition@0 { reg = <0x0 0x40000>; label = "u-boot"; }; partition@40000 { reg = <0x40000 0x10000>; label = "u-boot-env"; layout { compatible = "u-boot,env-layout"; }; }; partition@50000 { reg = <0x50000 0x100000>; label = "u-boot"; }; }; };Quoted 3 lines
but I can clearly see a use for nested "layout"s. As I said maybe we just shouldn't be so open in calling those MTD or NVMEM devices as that is kind of Linux specific.
The overall structure should be agnostic to the subsystem. Specific compatibles like 'u-boot,env' can be tied to a subsystem.
Maybe some things need to be both MTD and NVMEM. MTD to operate on the opague region and NVMEM to access the contents.
Quoted 6 lines
Quoted 2 lines
I'm not sure if we should try renaming "nvmem-layout" to "layout" or "partitions" in similar way at this point.
You can't rename. It's an ABI though maybe the whole "nvmem-layout" is new enough we can. It's looking like it was a mistake to accept any of this.
I don't think so.
A partition and a layout are not the same concept, as acknowledged above. We need both, and we need both because we can encapsulate both as well:
flash { partitions { partA@x { layout { cell@Y } } } }
Renaming nvmem-layout to layout can be done if you want, I don't mind, but I don't see the point in doing that.
Thanks,
Miquèl