iommu/amd: SVA Support (Part 4) - SVA and IOPF
Subsystems (2)
Vasant Hegde
maintainerv5 cover iommu/amd: SVA Support (Part 4) - SVA and IOPF
This is part 4 of the 4-part series to introduce Share Virtual Address (SVA) support for devices, which can support PCI ATS, PASID and PRI capabilities. These devices are referred to as SVA-capable devices in this series.
It contains the following enhancements:
* Patch 1 - 3:
Rename, add support to enable/disable features, update DTE etc.
* Patch 4 - 10:
Add IOPF support
* Patch 11 - 14:
Introduce SVA support
This patch series is based on top of SVA Part 3 v5.
https://lore.kernel.org/linux-iommu/[email protected]/T/#t
Also depends on :
1) Baolu's IOPF improvement
https://lore.kernel.org/linux-iommu/[email protected]/
This is also available at github :
https://github.com/AMDESE/linux/tree/iommu_sva_part4_v4_v6.7_rc8
Thanks everyone who reviewed previous version and provided valuable feedbacks.
Changes from v4 -> v5:
- Rebased on top of v6.7-rc8 + SVA Part3 patches
- Few minor improvements like renaming structure name for better, introducing macros, etc
V4: https://lore.kernel.org/linux-iommu/[email protected]/
Changes from v3 -> v4:
- Moved amd_iommu_dev_update_dte() after set/clear_dte() so that we can avoid forward declaration
- Dropped "iommu/amd: Do not override PASID entry in GCR3 table"
- Added patch to fix PPR interrupt processing logic
- Renamed enable_iommus_v2() -> enable_iommus_ppr()
- Added ops->domain_alloc_sva()
- Added domain_alloc_sva() support and reorganize SVA patches
- In error path iommu_call_iopf_notifier() calls amd_iommu_complete_ppr() instead of amd_iommu_page_response()
v3: https://lore.kernel.org/linux-iommu/[email protected]/T/#t
Changes from v2 -> v3:
- Rename sva.c -> pasid.c
- Changed amd_iommu_sva_supported() -> amd_iommu_pasid_supported()
- Added patch to update/flush DTE
- Rework part of SVA support
- Move IOPF enablement to PASID bind time
v2: https://lore.kernel.org/linux-iommu/[email protected]/T/#u
Changes from v1 -> v2:
- Added new patch to fix PASID override issue in GCR3 table
- Complete rework of SVA code on top of Tina's SVA series.
- Rework SVA enable code
- Reworked IOPF handler code on top of Baolu's IOPF improvement series.
v1: https://lore.kernel.org/linux-iommu/[email protected]/T/#t
Thank you,
Vasant / Suravee
Jason Gunthorpe (1):
iommu: Add ops->domain_alloc_sva()
Suravee Suthikulpanit (5):
iommu/amd: Move PPR-related functions into ppr.c iommu/amd: Define per-IOMMU iopf_queue iommu/amd: Add support for page response iommu/amd: Introduce logic to enable/disable IOPF iommu/amd: Add GCR3 [un]initialization function
Vasant Hegde (5):
iommu/amd: Rename amd_iommu_v2_supported() as
amd_iommu_pasid_supported()
iommu/amd: Introduce per device DTE update function iommu/amd: Fix PPR interrupt processing logic iommu/amd: Initial SVA support for AMD IOMMU iommu/amd: Add SVA domain support
Wei Huang (3):
iommu/amd: Add support for enabling/disabling IOMMU features iommu/amd: Add support for add/remove device for IOPF iommu/amd: Add IO page fault notifier handler
drivers/iommu/amd/Kconfig | 2 + drivers/iommu/amd/Makefile | 2 +- drivers/iommu/amd/amd_iommu.h | 51 +++- drivers/iommu/amd/amd_iommu_types.h | 32 +++ drivers/iommu/amd/init.c | 79 ++----- drivers/iommu/amd/iommu.c | 190 +++++++++------ drivers/iommu/amd/pasid.c | 271 +++++++++++++++++++++ drivers/iommu/amd/ppr.c | 354 ++++++++++++++++++++++++++++ drivers/iommu/iommu-sva.c | 16 +- include/linux/iommu.h | 3 + 10 files changed, 858 insertions(+), 142 deletions(-) create mode 100644 drivers/iommu/amd/pasid.c create mode 100644 drivers/iommu/amd/ppr.c
Signature · 1 line
2.31.1
Vasant Hegde
maintainerPATCH v5 1/14 iommu/amd: Rename amd_iommu_v2_supported() as amd_iommu_pasid_supported()
To reflect its usage. No functional changes intended.
--- drivers/iommu/amd/amd_iommu.h | 2 +- drivers/iommu/amd/init.c | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-)
drivers/iommu/amd/amd_iommu.h +1 -1
@@ -38,7 +38,7 @@ extern int amd_iommu_guest_ir;extern enum io_pgtable_fmt amd_iommu_pgtable;extern int amd_iommu_gpt_level; -bool amd_iommu_v2_supported (void ); +bool amd_iommu_pasid_supported (void );struct amd_iommu *get_amd_iommu (unsigned int idx);u8 amd_iommu_pc_get_max_banks (unsigned int idx);bool amd_iommu_pc_supported (void );
drivers/iommu/amd/init.c +1 -1
@@ -3652,7 +3652,7 @@ __setup("ivrs_ioapic", parse_ivrs_ioapic);__setup ("ivrs_hpet" , parse_ivrs_hpet);__setup ("ivrs_acpihid" , parse_ivrs_acpihid); -bool amd_iommu_v2_supported (void ) +bool amd_iommu_pasid_supported (void ) {/* CPU page table size should match IOMMU guest page table size */ if (cpu_feature_enabled(X86_FEATURE_LA57) &&
Signature · 1 line
2.31.1
Vasant Hegde
maintainerPATCH v5 2/14 iommu/amd: Introduce per device DTE update function
In reply to Vasant HegdeConsolidate per device update and flush logic into separate function. Also make it as global function as it will be used in subsequent series to update the DTE.
--- drivers/iommu/amd/amd_iommu.h | 1 + drivers/iommu/amd/iommu.c | 26 ++++++++++++++++++-------- 2 files changed, 19 insertions(+), 8 deletions(-)
drivers/iommu/amd/amd_iommu.h +1 -0
@@ -64,6 +64,7 @@ int amd_iommu_clear_gcr3(struct iommu_dev_data *dev_data, ioasid_t pasid);void amd_iommu_flush_all_caches (struct amd_iommu *iommu);void amd_iommu_update_and_flush_device_table (struct protection_domain *domain);void amd_iommu_domain_update (struct protection_domain *domain); +void amd_iommu_dev_update_dte (struct iommu_dev_data *dev_data,bool set);void amd_iommu_domain_flush_complete (struct protection_domain *domain);void amd_iommu_domain_flush_pages (struct protection_domain *domain,u64 address,size_t size);
drivers/iommu/amd/iommu.c +18 -8
@@ -2000,6 +2000,21 @@ static void clear_dte_entry(struct amd_iommu *iommu, u16 devid)amd_iommu_apply_erratum_63 (iommu, devid); } +/* Update and flush DTE for the given device */ +void amd_iommu_dev_update_dte (struct iommu_dev_data *dev_data,bool set) +{ +struct amd_iommu *iommu =get_amd_iommu_from_dev (dev_data->dev); + +if (set) +set_dte_entry (iommu, dev_data); +else +clear_dte_entry (iommu, dev_data->devid); + +clone_aliases (iommu, dev_data->dev); +device_flush_dte (dev_data); +iommu_completion_wait (iommu); +} +static int do_attach (struct iommu_dev_data *dev_data,struct protection_domain *domain) {
@@ -2039,10 +2054,7 @@ static int do_attach(struct iommu_dev_data *dev_data, }/* Update device table */ -set_dte_entry (iommu, dev_data); -clone_aliases (iommu, dev_data->dev); - -device_flush_dte (dev_data); +amd_iommu_dev_update_dte (dev_data, true);return ret; }
@@ -2061,11 +2073,9 @@ static void do_detach(struct iommu_dev_data *dev_data)/* Update data structures */ dev_data->domain =NULL ;list_del (&dev_data->list); -clear_dte_entry (iommu, dev_data->devid); -clone_aliases (iommu, dev_data->dev); -/* Flush the DTE entry */ -device_flush_dte (dev_data); +/* Clear DTE and flush the entry */ +amd_iommu_dev_update_dte (dev_data, false);/* Flush IOTLB and wait for the flushes to finish */ amd_iommu_domain_flush_all (domain);
Signature · 1 line
2.31.1
Re: [PATCH v5 02/14] iommu/amd: Introduce per device DTE update function
Quoted 9 lines · Vasant Hegde
Consolidate per device update and flush logic into separate function. Also make it as global function as it will be used in subsequent series to update the DTE.
Signed-off-by Vasant Hegde <[email protected]>--- drivers/iommu/amd/amd_iommu.h | 1 + drivers/iommu/amd/iommu.c | 26 ++++++++++++++++++-------- 2 files changed, 19 insertions(+), 8 deletions(-)
Jason
Vasant Hegde
maintainerPATCH v5 3/14 iommu/amd: Add support for enabling/disabling IOMMU features
In reply to Vasant HegdeFrom: Wei Huang <[email protected]>
Add support for struct iommu_ops.dev_{enable/disable}_feat. Please note that the empty feature switches will be populated by subsequent patches.
--- drivers/iommu/amd/iommu.c | 28 ++++++++++++++++++++++++++++ 1 file changed, 28 insertions(+)
drivers/iommu/amd/iommu.c +28 -0
@@ -2799,6 +2799,32 @@ static const struct iommu_dirty_ops amd_dirty_ops = { .read_and_clear_dirty = amd_iommu_read_and_clear_dirty, }; +static int amd_iommu_dev_enable_feature (struct device *dev, +enum iommu_dev_features feat) +{ +int ret; + +switch (feat) { +default : + ret = -EINVAL ; +break ; + } +return ret; +} + +static int amd_iommu_dev_disable_feature (struct device *dev, +enum iommu_dev_features feat) +{ +int ret; + +switch (feat) { +default : + ret = -EINVAL ; +break ; + } +return ret; +} +const struct iommu_ops amd_iommu_ops = { .capable = amd_iommu_capable, .domain_alloc = amd_iommu_domain_alloc,
@@ -2811,6 +2837,8 @@ const struct iommu_ops amd_iommu_ops = { .is_attach_deferred = amd_iommu_is_attach_deferred, .pgsize_bitmap = AMD_IOMMU_PGSIZES, .def_domain_type = amd_iommu_def_domain_type, + .dev_enable_feat = amd_iommu_dev_enable_feature, + .dev_disable_feat = amd_iommu_dev_disable_feature, .default_domain_ops = &(const struct iommu_domain_ops ) { .attach_dev = amd_iommu_attach_device, .map_pages = amd_iommu_map_pages,
Signature · 1 line
2.31.1
Vasant Hegde
maintainerPATCH v5 4/14 iommu/amd: Move PPR-related functions into ppr.c
In reply to Vasant HegdeFrom: Suravee Suthikulpanit <[email protected]>
In preparation to subsequent PPR-related patches, and also remove static declaration for certain helper functions so that it can be reused in other files.
Also rename below functions:
alloc_ppr_log -> amd_iommu_alloc_ppr_log
iommu_enable_ppr_log -> amd_iommu_enable_ppr_log
free_ppr_log -> amd_iommu_free_ppr_log
iommu_poll_ppr_log -> amd_iommu_poll_ppr_log
--- drivers/iommu/amd/Makefile | 2 +- drivers/iommu/amd/amd_iommu.h | 17 +++++- drivers/iommu/amd/init.c | 65 +++----------------- drivers/iommu/amd/iommu.c | 55 +---------------- drivers/iommu/amd/ppr.c | 112 ++++++++++++++++++++++++++++++++++ 5 files changed, 137 insertions(+), 114 deletions(-) create mode 100644 drivers/iommu/amd/ppr.c
drivers/iommu/amd/Makefile +1 -1
@@ -1,3 +1,3 @@ # SPDX-License-Identifier: GPL-2.0-only -obj-$(CONFIG_AMD_IOMMU) += iommu.o init.o quirks.o io_pgtable.o io_pgtable_v2.o +obj-$(CONFIG_AMD_IOMMU) += iommu.o init.o quirks.o io_pgtable.o io_pgtable_v2.o ppr.o obj-$(CONFIG_AMD_IOMMU_DEBUGFS) += debugfs.o
drivers/iommu/amd/amd_iommu.h +14 -3
@@ -17,10 +17,16 @@ irqreturn_t amd_iommu_int_thread_pprlog(int irq, void *data);irqreturn_t amd_iommu_int_thread_galog (int irq,void *data);irqreturn_t amd_iommu_int_handler (int irq,void *data);void amd_iommu_apply_erratum_63 (struct amd_iommu *iommu,u16 devid); +void amd_iommu_restart_log (struct amd_iommu *iommu,const char *evt_type, +u8 cntrl_intr,u8 cntrl_log, +u32 status_run_mask,u32 status_overflow_mask);void amd_iommu_restart_event_logging (struct amd_iommu *iommu);void amd_iommu_restart_ga_log (struct amd_iommu *iommu);void amd_iommu_restart_ppr_log (struct amd_iommu *iommu);void amd_iommu_set_rlookup_table (struct amd_iommu *iommu,u16 devid); +void iommu_feature_enable (struct amd_iommu *iommu,u8 bit); +void *__init iommu_alloc_4k_pages (struct amd_iommu *iommu, +gfp_t gfp,size_t size);#ifdef CONFIG_AMD_IOMMU_DEBUGFS void amd_iommu_debugfs_setup (struct amd_iommu *iommu);
@@ -57,6 +63,14 @@ int amd_iommu_set_gcr3(struct iommu_dev_data *dev_data, ioasid_t pasid, unsigned long gcr3);int amd_iommu_clear_gcr3 (struct iommu_dev_data *dev_data,ioasid_t pasid); +/* PPR */ +int __init amd_iommu_alloc_ppr_log (struct amd_iommu *iommu); +void __init amd_iommu_free_ppr_log (struct amd_iommu *iommu); +void amd_iommu_enable_ppr_log (struct amd_iommu *iommu); +void amd_iommu_poll_ppr_log (struct amd_iommu *iommu); +int amd_iommu_complete_ppr (struct pci_dev *pdev,u32 pasid, +int status,int tag); +/* * This function flushes all internal caches of * the IOMMU used by this driver.
@@ -86,9 +100,6 @@ static inline int amd_iommu_create_irq_domain(struct amd_iommu *iommu)#define PPR_INVALID 0x1#define PPR_FAILURE 0xf -int amd_iommu_complete_ppr (struct pci_dev *pdev,u32 pasid, -int status,int tag); -static inline bool is_rd890_iommu (struct pci_dev *pdev) { return (pdev->vendor == PCI_VENDOR_ID_ATI) &&
drivers/iommu/amd/init.c +9 -56
113 lines not on this page · raw message
drivers/iommu/amd/iommu.c +1 -54
67 lines not on this page · raw message
drivers/iommu/amd/ppr.c new file +112 -0
112 lines not on this page · raw message
Signature · 1 line
2.31.1
Re: [PATCH v5 04/14] iommu/amd: Move PPR-related functions into ppr.c
Quoted 15 lines · Vasant Hegde
From: Suravee Suthikulpanit <[email protected]>
In preparation to subsequent PPR-related patches, and also remove static declaration for certain helper functions so that it can be reused in other files.
Also rename below functions:
alloc_ppr_log->amd_iommu_alloc_ppr_log
iommu_enable_ppr_log->amd_iommu_enable_ppr_log
free_ppr_log->amd_iommu_free_ppr_log
iommu_poll_ppr_log->amd_iommu_poll_ppr_logSigned-off-by Suravee Suthikulpanit <[email protected]>Co-developed-by Vasant Hegde <[email protected]>Signed-off-by Vasant Hegde <[email protected]>
Quoted 8 lines
--- drivers/iommu/amd/Makefile | 2 +- drivers/iommu/amd/amd_iommu.h | 17 +++++- drivers/iommu/amd/init.c | 65 +++----------------- drivers/iommu/amd/iommu.c | 55 +---------------- drivers/iommu/amd/ppr.c | 112 ++++++++++++++++++++++++++++++++++ 5 files changed, 137 insertions(+), 114 deletions(-) create mode 100644 drivers/iommu/amd/ppr.c
Jason
Vasant Hegde
maintainerPATCH v5 5/14 iommu/amd: Fix PPR interrupt processing logic
In reply to Vasant Hegde* Do not re-read ppr head pointer as its just updated by the driver.
* Do not read PPR buffer tail pointer inside while loop. If IOMMU generates PPR events continuously then completing interrupt processing takes long time. In worst case it may cause infinite loop.
--- drivers/iommu/amd/ppr.c | 4 ---- 1 file changed, 4 deletions(-)
drivers/iommu/amd/ppr.c +0 -4
@@ -104,9 +104,5 @@ void amd_iommu_poll_ppr_log(struct amd_iommu *iommu)writel (head, iommu->mmio_base +MMIO_PPR_HEAD_OFFSET );/* TODO: PPR Handler will be added when we add IOPF support */ - -/* Refresh ring-buffer information */ - head =readl (iommu->mmio_base +MMIO_PPR_HEAD_OFFSET ); - tail =readl (iommu->mmio_base +MMIO_PPR_TAIL_OFFSET ); } }
Signature · 1 line
2.31.1
Re: [PATCH v5 05/14] iommu/amd: Fix PPR interrupt processing logic
Quoted 11 lines · Vasant Hegde
* Do not re-read ppr head pointer as its just updated by the driver.
* Do not read PPR buffer tail pointer inside while loop. If IOMMU generates PPR events continuously then completing interrupt processing takes long time. In worst case it may cause infinite loop.
Suggested-by Tom Lendacky <[email protected]>Signed-off-by Vasant Hegde <[email protected]>--- drivers/iommu/amd/ppr.c | 4 ---- 1 file changed, 4 deletions(-)
Jason
Vasant Hegde
maintainerPATCH v5 6/14 iommu/amd: Define per-IOMMU iopf_queue
In reply to Vasant HegdeFrom: Suravee Suthikulpanit <[email protected]>
AMD IOMMU hardware supports PCI Peripheral Paging Request (PPR) using a PPR log, which is a circular buffer containing requests from downstream end-point devices.
There is one PPR log per IOMMU instance. Therefore, allocate an iopf_queue per IOMMU instance during driver initialization, and free the queue during driver deinitialization.
Also rename enable_iommus_v2() -> enable_iommus_ppr() to reflect its usage.
--- drivers/iommu/amd/amd_iommu.h | 5 ++++ drivers/iommu/amd/amd_iommu_types.h | 4 +++ drivers/iommu/amd/init.c | 12 ++++++--- drivers/iommu/amd/ppr.c | 42 +++++++++++++++++++++++++++++ 4 files changed, 60 insertions(+), 3 deletions(-)
drivers/iommu/amd/amd_iommu.h +5 -0
@@ -45,6 +45,11 @@ extern enum io_pgtable_fmt amd_iommu_pgtable;extern int amd_iommu_gpt_level;bool amd_iommu_pasid_supported (void ); + +/* IOPF */ +int amd_iommu_iopf_init (struct amd_iommu *iommu); +void amd_iommu_iopf_uninit (struct amd_iommu *iommu); +struct amd_iommu *get_amd_iommu (unsigned int idx);u8 amd_iommu_pc_get_max_banks (unsigned int idx);bool amd_iommu_pc_supported (void );
drivers/iommu/amd/amd_iommu_types.h +4 -0
@@ -770,6 +770,10 @@ struct amd_iommu {/* DebugFS Info */ struct dentry *debugfs;#endif + +/* IOPF support */ +struct iopf_queue *iopf_queue; +unsigned char iopfq_name[32 ]; };static inline struct amd_iommu *dev_to_amd_iommu (struct device *dev)
drivers/iommu/amd/init.c +9 -3
@@ -1638,6 +1638,7 @@ static void __init free_iommu_one(struct amd_iommu *iommu)amd_iommu_free_ppr_log (iommu);free_ga_log (iommu);iommu_unmap_mmio_space (iommu); +amd_iommu_iopf_uninit (iommu); }static void __init free_iommu_all (void )
@@ -2789,12 +2790,17 @@ static void early_enable_iommus(void) } } -static void enable_iommus_v2 (void ) +static void enable_iommus_ppr (void ) {struct amd_iommu *iommu; -for_each_iommu (iommu) +if (!amd_iommu_gt_ppr_supported ()) +return ; + +for_each_iommu (iommu) {amd_iommu_enable_ppr_log (iommu); +amd_iommu_iopf_init (iommu); + } }static void enable_iommus_vapic (void )
@@ -3130,7 +3136,7 @@ static int amd_iommu_enable_interrupts(void)* PPR and GA log interrupt for all IOMMUs. */ enable_iommus_vapic (); -enable_iommus_v2 (); +enable_iommus_ppr (); out:return ret;
drivers/iommu/amd/ppr.c +42 -0
45 lines not on this page · raw message
Signature · 1 line
2.31.1
Re: [PATCH v5 06/14] iommu/amd: Define per-IOMMU iopf_queue
Quoted 16 lines · Vasant Hegde
From: Suravee Suthikulpanit <[email protected]>
AMD IOMMU hardware supports PCI Peripheral Paging Request (PPR) using a PPR log, which is a circular buffer containing requests from downstream end-point devices.
There is one PPR log per IOMMU instance. Therefore, allocate an
iopf_queueper IOMMU instance during driver initialization, and free the queue during driver deinitialization.Also rename
enable_iommus_v2()->enable_iommus_ppr()to reflect its usage.Signed-off-by Suravee Suthikulpanit <[email protected]>Co-developed-by Vasant Hegde <[email protected]>Signed-off-by Vasant Hegde <[email protected]>
Quoted 6 lines
--- drivers/iommu/amd/amd_iommu.h | 5 ++++ drivers/iommu/amd/amd_iommu_types.h | 4 +++ drivers/iommu/amd/init.c | 12 ++++++--- drivers/iommu/amd/ppr.c | 42 +++++++++++++++++++++++++++++ 4 files changed, 60 insertions(+), 3 deletions(-)
Jason
Vasant Hegde
maintainerPATCH v5 7/14 iommu/amd: Add support for page response
In reply to Vasant HegdeFrom: Suravee Suthikulpanit <[email protected]>
This generates AMD IOMMU COMPLETE_PPR_REQUEST for the specified device with the specified PRI Response Code.
--- drivers/iommu/amd/amd_iommu.h | 3 +++ drivers/iommu/amd/iommu.c | 1 + drivers/iommu/amd/ppr.c | 15 +++++++++++++++ 3 files changed, 19 insertions(+)
drivers/iommu/amd/amd_iommu.h +3 -0
@@ -49,6 +49,9 @@ bool amd_iommu_pasid_supported(void);/* IOPF */ int amd_iommu_iopf_init (struct amd_iommu *iommu);void amd_iommu_iopf_uninit (struct amd_iommu *iommu); +int amd_iommu_page_response (struct device *dev, +struct iopf_fault *evt, +struct iommu_page_response *resp);struct amd_iommu *get_amd_iommu (unsigned int idx);u8 amd_iommu_pc_get_max_banks (unsigned int idx);
drivers/iommu/amd/iommu.c +1 -0
@@ -2786,6 +2786,7 @@ const struct iommu_ops amd_iommu_ops = { .def_domain_type = amd_iommu_def_domain_type, .dev_enable_feat = amd_iommu_dev_enable_feature, .dev_disable_feat = amd_iommu_dev_disable_feature, + .page_response = amd_iommu_page_response, .default_domain_ops = &(const struct iommu_domain_ops ) { .attach_dev = amd_iommu_attach_device, .map_pages = amd_iommu_map_pages,
drivers/iommu/amd/ppr.c +15 -0
@@ -148,3 +148,18 @@ void amd_iommu_iopf_uninit(struct amd_iommu *iommu)raw_spin_unlock_irqrestore (&iommu->lock, flags); } + +int amd_iommu_page_response (struct device *dev, +struct iopf_fault *evt, +struct iommu_page_response *resp) +{ +struct pci_dev *pdev; + +if (!dev || !dev_is_pci (dev)) +return -ENODEV ; + + pdev =to_pci_dev (dev); + +return amd_iommu_complete_ppr (pdev, resp->pasid, resp->code, + resp->grpid); +}
Signature · 1 line
2.31.1
Re: [PATCH v5 07/14] iommu/amd: Add support for page response
Quoted 12 lines · Vasant Hegde
drivers/iommu/amd/ppr.c +4
-0@@ -148,3 +148,18 @@ void amd_iommu_iopf_uninit(struct amd_iommu *iommu)raw_spin_unlock_irqrestore (&iommu->lock, flags); } + +int amd_iommu_page_response (struct device *dev, +struct iopf_fault *evt, +struct iommu_page_response *resp)
drivers/iommu/amd/ppr.c void amd_iommu_iopf_uninit(struct amd_iommu *iommu) · line 164
Quoted 10 lines
drivers/iommu/amd/ppr.c +10
-0+{ +struct pci_dev *pdev; + +if (!dev || !dev_is_pci (dev)) +return -ENODEV ; + + pdev =to_pci_dev (dev); + +return amd_iommu_complete_ppr (pdev, resp->pasid, resp->code, + resp->grpid);
Converting this to a pci_dev seems pointless? Nothing reaches into the PCI struct. Why do it?
We don't need sanity checking here on the fast path..
Jason
Vasant Hegde
maintainerRe: [PATCH v5 07/14] iommu/amd: Add support for page response
Jason,
Quoted 19 lines · Jason Gunthorpe
Quoted 17 lines · Vasant Hegde
drivers/iommu/amd/ppr.c +9
-0@@ -148,3 +148,18 @@ void amd_iommu_iopf_uninit(struct amd_iommu *iommu)raw_spin_unlock_irqrestore (&iommu->lock, flags); } + +int amd_iommu_page_response (struct device *dev, +struct iopf_fault *evt, +struct iommu_page_response *resp) +{ +struct pci_dev *pdev; + +if (!dev || !dev_is_pci (dev)) +return -ENODEV ;
Quoted 8 lines
drivers/iommu/amd/ppr.c void amd_iommu_iopf_uninit(struct amd_iommu *iommu) · line 164
Quoted 5 lines
drivers/iommu/amd/ppr.c +5
-0+ + pdev =to_pci_dev (dev); + +return amd_iommu_complete_ppr (pdev, resp->pasid, resp->code, + resp->grpid);Converting this to a
pci_devseems pointless? Nothing reaches into the PCI struct. Why do it?
I can update amd_iommu_complete_ppr() to accept 'struct device' instead of pdev as we don't need pdev reference inside amd_iommu_complete_ppr().
Will fix it in v6.
-Vasant
Vasant Hegde
maintainerPATCH v5 8/14 iommu/amd: Add support for add/remove device for IOPF
In reply to Vasant HegdeFrom: Wei Huang <[email protected]>
Which adds/removes the device to the corresponding per-IOMMU iopf_queue. It also registers device fault handler. These interfaces are called from IOPF feature enable/disable path.
--- drivers/iommu/amd/amd_iommu.h | 2 ++ drivers/iommu/amd/ppr.c | 35 +++++++++++++++++++++++++++++++++++ 2 files changed, 37 insertions(+)
drivers/iommu/amd/amd_iommu.h +2 -0
@@ -49,6 +49,8 @@ bool amd_iommu_pasid_supported(void);/* IOPF */ int amd_iommu_iopf_init (struct amd_iommu *iommu);void amd_iommu_iopf_uninit (struct amd_iommu *iommu); +int amd_iommu_iopf_add_device (struct amd_iommu *iommu,struct device *dev); +int amd_iommu_iopf_remove_device (struct amd_iommu *iommu,struct device *dev);int amd_iommu_page_response (struct device *dev,struct iopf_fault *evt,struct iommu_page_response *resp);
drivers/iommu/amd/ppr.c +35 -0
@@ -163,3 +163,38 @@ int amd_iommu_page_response(struct device *dev,return amd_iommu_complete_ppr (pdev, resp->pasid, resp->code, resp->grpid); } + +int amd_iommu_iopf_add_device (struct amd_iommu *iommu,struct device *dev) +{ +unsigned long flags; +int ret = -EINVAL ; + +raw_spin_lock_irqsave (&iommu->lock, flags); + +if (!iommu->iopf_queue) { +raw_spin_unlock_irqrestore (&iommu->lock, flags); +return ret; + } + + ret =iopf_queue_add_device (iommu->iopf_queue, dev); + +raw_spin_unlock_irqrestore (&iommu->lock, flags); +return ret; +} + +int amd_iommu_iopf_remove_device (struct amd_iommu *iommu,struct device *dev) +{ +unsigned long flags; + +raw_spin_lock_irqsave (&iommu->lock, flags); + +if (!iommu->iopf_queue) { +raw_spin_unlock_irqrestore (&iommu->lock, flags); +return -EINVAL ; + } + +iopf_queue_remove_device (iommu->iopf_queue, dev); + +raw_spin_unlock_irqrestore (&iommu->lock, flags); +return 0 ; +}
Signature · 1 line
2.31.1
Re: [PATCH v5 08/14] iommu/amd: Add support for add/remove device for IOPF
Quoted 5 lines · Vasant Hegde
From: Wei Huang <[email protected]>
Which adds/removes the device to the corresponding per-IOMMU
iopf_queue. It also registers device fault handler. These interfaces are called from IOPF feature enable/disable path.
"fault handler"? Not anymore right?
They should not be called from the iopf feature path :(
Quoted 9 lines
drivers/iommu/amd/ppr.c +1
-0@@ -163,3 +163,38 @@ int amd_iommu_page_response(struct device *dev,return amd_iommu_complete_ppr (pdev, resp->pasid, resp->code, resp->grpid); } +
drivers/iommu/amd/ppr.c int amd_iommu_page_response(struct device *dev, · line 176
Quoted 10 lines
drivers/iommu/amd/ppr.c +10
-0+int amd_iommu_iopf_add_device (struct amd_iommu *iommu,struct device *dev) +{ +unsigned long flags; +int ret = -EINVAL ; + +raw_spin_lock_irqsave (&iommu->lock, flags); + +if (!iommu->iopf_queue) { +raw_spin_unlock_irqrestore (&iommu->lock, flags); +return ret;
goto out_unlock if you are going to write it like that
Jason
Vasant Hegde
maintainerRe: [PATCH v5 08/14] iommu/amd: Add support for add/remove device for IOPF
Jason,
Quoted 8 lines · Jason Gunthorpe
Quoted 5 lines · Vasant Hegde
From: Wei Huang <[email protected]>
Which adds/removes the device to the corresponding per-IOMMU
iopf_queue. It also registers device fault handler. These interfaces are called from IOPF feature enable/disable path."fault handler"? Not anymore right?
Yes. It adds device to IOMMU IOPF queue so that we can handler faults from device.
Quoted 2 lines
They should not be called from the iopf feature path :(
We enable IOPF feature (and device PASID) in set_dev_pasid() path when we attach first PASID to device.
Quoted 14 lines
Quoted 14 lines
drivers/iommu/amd/ppr.c +5
-0@@ -163,3 +163,38 @@ int amd_iommu_page_response(struct device *dev,return amd_iommu_complete_ppr (pdev, resp->pasid, resp->code, resp->grpid); } + +int amd_iommu_iopf_add_device (struct amd_iommu *iommu,struct device *dev) +{ +unsigned long flags; +int ret = -EINVAL ;
Quoted 8 lines
drivers/iommu/amd/ppr.c int amd_iommu_page_response(struct device *dev, · line 176
Quoted 6 lines
drivers/iommu/amd/ppr.c +6
-0+ +raw_spin_lock_irqsave (&iommu->lock, flags); + +if (!iommu->iopf_queue) { +raw_spin_unlock_irqrestore (&iommu->lock, flags); +return ret;goto
out_unlockif you are going to write it like that
Ok.
-Vasant
Vasant Hegde
maintainerPATCH v5 9/14 iommu/amd: Add IO page fault notifier handler
In reply to Vasant HegdeFrom: Wei Huang <[email protected]>
Whenever there is a page fault IOMMU logs entry to ppr log and sends interrupt to host. We have to handle the page fault and respond to IOMMU.
Add support to validate page fault request and hook it to core iommu page fault handler.
--- drivers/iommu/amd/amd_iommu_types.h | 8 +++ drivers/iommu/amd/ppr.c | 99 ++++++++++++++++++++++++++++- 2 files changed, 106 insertions(+), 1 deletion(-)
drivers/iommu/amd/amd_iommu_types.h +8 -0
@@ -251,6 +251,14 @@#define PPR_ENTRY_SIZE 16#define PPR_LOG_SIZE (PPR_ENTRY_SIZE * PPR_LOG_ENTRIES) +/* PAGE_SERVICE_REQUEST PPR Log Buffer Entry flags */ +#define PPR_FLAG_EXEC 0x002/* Execute permission requested */ +#define PPR_FLAG_READ 0x004/* Read permission requested */ +#define PPR_FLAG_WRITE 0x020/* Write permission requested */ +#define PPR_FLAG_US 0x040/* 1: User, 0: Supervisor */ +#define PPR_FLAG_RVSD 0x080/* Reserved bit not zero */ +#define PPR_FLAG_GN 0x100/* GVA and PASID is valid */ +#define PPR_REQ_TYPE (x) (((x) >> 60) & 0xfULL)#define PPR_FLAGS (x) (((x) >> 48) & 0xfffULL)#define PPR_DEVID (x) ((x) & 0xffffULL)
drivers/iommu/amd/ppr.c +98 -1
111 lines not on this page · raw message
Signature · 1 line
2.31.1
Vasant Hegde
maintainerPATCH v5 10/14 iommu/amd: Introduce logic to enable/disable IOPF
In reply to Vasant HegdeFrom: Suravee Suthikulpanit <[email protected]>
Add support to enable/disable IOPF feature. So that PRI capable device can make use of page fault handler in SVA mode.
Note that enable_feature(IOPF) just returns success, as this interface is going away. IOPF handler will be setup in PASID bind path. Following patch will add this support.
Also add IOMMU_IOPF as dependency to AMD_IOMMU driver.
--- drivers/iommu/amd/Kconfig | 1 + drivers/iommu/amd/amd_iommu.h | 2 ++ drivers/iommu/amd/iommu.c | 8 +++-- drivers/iommu/amd/ppr.c | 57 +++++++++++++++++++++++++++++++++++ 4 files changed, 66 insertions(+), 2 deletions(-)
drivers/iommu/amd/Kconfig +1 -0
@@ -10,6 +10,7 @@ config AMD_IOMMU select IOMMU_API select IOMMU_IOVA select IOMMU_IO_PGTABLE + select IOMMU_IOPF select IOMMUFD_DRIVER if IOMMUFD depends on X86_64 && PCI && ACPI && HAVE_CMPXCHG_DOUBLE help
drivers/iommu/amd/amd_iommu.h +2 -0
@@ -54,6 +54,8 @@ int amd_iommu_iopf_remove_device(struct amd_iommu *iommu, struct device *dev);int amd_iommu_page_response (struct device *dev,struct iopf_fault *evt,struct iommu_page_response *resp); +int amd_iommu_iopf_enable_device (struct device *dev); +int amd_iommu_iopf_disable_device (struct device *dev);struct amd_iommu *get_amd_iommu (unsigned int idx);u8 amd_iommu_pc_get_max_banks (unsigned int idx);
drivers/iommu/amd/iommu.c +6 -2
@@ -2749,9 +2749,11 @@ static const struct iommu_dirty_ops amd_dirty_ops = {static int amd_iommu_dev_enable_feature (struct device *dev,enum iommu_dev_features feat) { -int ret; +int ret =0 ;switch (feat) { +case IOMMU_DEV_FEAT_IOPF : +break ;default : ret = -EINVAL ;break ;
@@ -2762,9 +2764,11 @@ static int amd_iommu_dev_enable_feature(struct device *dev,static int amd_iommu_dev_disable_feature (struct device *dev,enum iommu_dev_features feat) { -int ret; +int ret =0 ;switch (feat) { +case IOMMU_DEV_FEAT_IOPF : +break ;default : ret = -EINVAL ;break ;
drivers/iommu/amd/ppr.c +57 -0
60 lines not on this page · raw message
Signature · 1 line
2.31.1
Re: [PATCH v5 10/14] iommu/amd: Introduce logic to enable/disable IOPF
Quoted 27 lines · Vasant Hegde
drivers/iommu/amd/ppr.c +19
-0@@ -295,3 +295,60 @@ int amd_iommu_iopf_remove_device(struct amd_iommu *iommu, struct device *dev)raw_spin_unlock_irqrestore (&iommu->lock, flags);return 0 ; } + +static int iopf_update_device (struct device *dev,bool enable) +{ +struct pci_dev *pdev =dev_is_pci (dev) ?to_pci_dev (dev) :NULL ; +struct amd_iommu *iommu =get_amd_iommu_from_dev (dev); +struct iommu_dev_data *dev_data =dev_iommu_priv_get (dev); +struct protection_domain *pdom = dev_data->domain; +int ret =0 ; + +if (!pdev || !pdom) +return -EINVAL ; + +spin_lock (&dev_data->lock); + +if (enable) { +if (dev_data->ppr) + goto out; + + ret =amd_iommu_iopf_add_device (iommu, dev);
drivers/iommu/amd/ppr.c int amd_iommu_iopf_remove_device(struct amd_iommu *iommu, struct device *dev) · line 326
Quoted 10 lines
drivers/iommu/amd/ppr.c +10
-0+if (ret) + goto out; + + dev_data->ppr = true; + }else { + ret =amd_iommu_iopf_remove_device (iommu, dev); + dev_data->ppr = false; + } + +amd_iommu_dev_update_dte (dev_data, true);
This dte change is in the wrong place. When the domain is first attached we know if it requires PRI or not. At that moment the DTE should be set properly, it should not be set wrong and then changed later.
Remember what I said earlier there should be one DTE write on the attach paths.
So probably all of this should go away and be moved into set dte
(and again the whole dte setting flow needs cleaning, I think you should do that before trying to build more complex stuff on top)
Jason
Vasant Hegde
maintainerRe: [PATCH v5 10/14] iommu/amd: Introduce logic to enable/disable IOPF
Jason,
Quoted 35 lines · Jason Gunthorpe
Quoted 34 lines · Vasant Hegde
drivers/iommu/amd/ppr.c +26
-0@@ -295,3 +295,60 @@ int amd_iommu_iopf_remove_device(struct amd_iommu *iommu, struct device *dev)raw_spin_unlock_irqrestore (&iommu->lock, flags);return 0 ; } + +static int iopf_update_device (struct device *dev,bool enable) +{ +struct pci_dev *pdev =dev_is_pci (dev) ?to_pci_dev (dev) :NULL ; +struct amd_iommu *iommu =get_amd_iommu_from_dev (dev); +struct iommu_dev_data *dev_data =dev_iommu_priv_get (dev); +struct protection_domain *pdom = dev_data->domain; +int ret =0 ; + +if (!pdev || !pdom) +return -EINVAL ; + +spin_lock (&dev_data->lock); + +if (enable) { +if (dev_data->ppr) + goto out; + + ret =amd_iommu_iopf_add_device (iommu, dev); +if (ret) + goto out; + + dev_data->ppr = true; + }else { + ret =amd_iommu_iopf_remove_device (iommu, dev); + dev_data->ppr = false;
Quoted 8 lines
drivers/iommu/amd/ppr.c int amd_iommu_iopf_remove_device(struct amd_iommu *iommu, struct device *dev) · line 326
Quoted 3 lines
drivers/iommu/amd/ppr.c +3
-0+ } + +amd_iommu_dev_update_dte (dev_data, true);This dte change is in the wrong place. When the domain is first attached we know if it requires PRI or not. At that moment the DTE should be set properly, it should not be set wrong and then changed later.
We want to enable PPR support only after setting up the handler.
Quoted 8 lines
Remember what I said earlier there should be one DTE write on the attach paths.
So probably all of this should go away and be moved into set dte
(and again the whole dte setting flow needs cleaning, I think you should do that before trying to build more complex stuff on top)
Yeah. I want to fix few things in that path. But that's outside this series.
-Vasant
Re: [PATCH v5 10/14] iommu/amd: Introduce logic to enable/disable IOPF
Quoted 6 lines · Vasant Hegde
Quoted 4 lines
This dte change is in the wrong place. When the domain is first attached we know if it requires PRI or not. At that moment the DTE should be set properly, it should not be set wrong and then changed later.
We want to enable PPR support only after setting up the handler.
That's backwards. It means error handling can't really be sane..
Quoted 4 lines
Quoted 2 lines
(and again the whole dte setting flow needs cleaning, I think you should do that before trying to build more complex stuff on top)
Yeah. I want to fix few things in that path. But that's outside this series.
I was looking at it and there are many security bugs in here now that iommufd can change the DTE at any time. The current design assumes DMA will be stopped and ignores the spec guidance on how to do a safe DTE update :(
I'm really not comfortable with adding more stuff here until the security issue is solved. Especially if the more stuff is drifting further from being correct. If you can keep the updates in set_dte then maybe with some reluctance. But not like this with random touches to the DTE all over the place.
I was looking at what it would take and got part way through. It is a very similar problem to ARM and I drafted a similar solution.
Jason
Vasant Hegde
maintainerRe: [PATCH v5 10/14] iommu/amd: Introduce logic to enable/disable IOPF
Jason,
Quoted 10 lines · Jason Gunthorpe
Quoted 6 lines · Vasant Hegde
Quoted 4 lines
This dte change is in the wrong place. When the domain is first attached we know if it requires PRI or not. At that moment the DTE should be set properly, it should not be set wrong and then changed later.
We want to enable PPR support only after setting up the handler.
That's backwards. It means error handling can't really be sane..
Why do you think enabling feature only when we are really going to use it backwards?
Quoted 10 lines
Quoted 5 lines
Quoted 3 lines
(and again the whole dte setting flow needs cleaning, I think you should do that before trying to build more complex stuff on top)
Yeah. I want to fix few things in that path. But that's outside this series.
I was looking at it and there are many security bugs in here now that iommufd can change the DTE at any time. The current design assumes DMA will be stopped and ignores the spec guidance on how to do a safe DTE update :(
What security issues are you referring? Can you elaborate?
Quoted 6 lines
I'm really not comfortable with adding more stuff here until the security issue is solved. Especially if the more stuff is drifting further from being correct. If you can keep the updates in
set_dtethen maybe with some reluctance. But not like this with random touches to the DTE all over the place.
Currently all DTE update is happening inside set_dte only (dirty bit enable is an exception that may need to moved inside set_dte). This patch just invokes that set_dte and invalidates cache.
-Vasant
Quoted 5 lines
I was looking at what it would take and got part way through. It is a very similar problem to ARM and I drafted a similar solution.
Jason
Re: [PATCH v5 10/14] iommu/amd: Introduce logic to enable/disable IOPF
Quoted 8 lines · Vasant Hegde
Quoted 7 lines · Jason Gunthorpe
Quoted 5 lines · Vasant Hegde
Quoted 4 lines
This dte change is in the wrong place. When the domain is first attached we know if it requires PRI or not. At that moment the DTE should be set properly, it should not be set wrong and then changed later.
Quoted 6 lines
Quoted 3 lines
Quoted 1 line
We want to enable PPR support only after setting up the handler.
That's backwards. It means error handling can't really be sane..
Why do you think enabling feature only when we are really going to use it backwards?
Because you touch the DTE twice, it means the domain is installed in an inconsistent state where it is not actually working properly. Domain updates should not "tear" like that.
You already know what is going to happen at the very start of attach, you don't need to "enable it after" just do it right the first time through.
There is a clear protocol and ordering requirement for the PRI enablement. Lu described it in a comment, make sure you follow it.
You also have to think about what happens during detach and what happens on all the pairs of attach -> attach.
The error unwinds are tricky, the only way I could make it all be correct for ARM was to fix the attach handling so that there is no failure scenario after the DTE is updated. ie the attach functions either do nothing or fully succeed.
The situation where attach fails and leaves the HW in an unknown state is really hard to deal with - and without the reliable global blocked domain the core code can't 100% rescue it either.
Quoted 11 lines
Quoted 9 lines
Quoted 4 lines
Quoted 2 lines
(and again the whole dte setting flow needs cleaning, I think you should do that before trying to build more complex stuff on top)
Yeah. I want to fix few things in that path. But that's outside this series.
I was looking at it and there are many security bugs in here now that iommufd can change the DTE at any time. The current design assumes DMA will be stopped and ignores the spec guidance on how to do a safe DTE update :(
What security issues are you referring? Can you elaborate?
The DTE is not updated correctly. The HW can read inconsistent versions of it with unpredictable - and possibly security bad - results.
Like it doesn't even write the two qwords of the DTE in a predicatble order! Let alone worrying about the 3 qw update or being correct with races during an ITE touch :(
This doesn't matter so much if there is no DMA active while the DTE is being changed, which could sort of reasonably be assumed up till iommufd allowed it to happen under userspace control.
Now a driver cannot make the assumption that DMA is halted. It must follow all the protocols to ensure that HW observes only exactly the DTEs/etc it is trying to build and not something random.
The documentation is pretty clear how this is supposed to work. It is the same as ARM. Use atomic 64/128 bit stores, rely on 'ignored behavior' or use the valid bit.
This also means, broadly, you can't allow the DTE to evolve during the operation of attach/detach as the in-between states may become userspace visible and may be harmful in some way.
Quoted 9 lines
Quoted 5 lines
I'm really not comfortable with adding more stuff here until the security issue is solved. Especially if the more stuff is drifting further from being correct. If you can keep the updates in
set_dtethen maybe with some reluctance. But not like this with random touches to the DTE all over the place.Currently all DTE update is happening inside
set_dteonly (dirty bit enable is an exception that may need to moved insideset_dte). This patch just invokes thatset_dteand invalidates cache.
So then why all this strangeness?? Just set dev_data->ppr earlier in attach and order the handler setup properly.
It should be really simple:
// All protected by the core's group mutex
if (domain->needs_pri) {
dev_data->ppr = true;
if (!dev_data->num_pri_domains)
// enable fault queues for the device
dev_data->num_pri_domains++}
if (old_domain->needs_pri) {
dev_data->num_pri_domains--;
if (!dev_data->num_pri_domains) {
dev_data->ppr = false;
disable pri at PCI()
}}
set_dte()
if (domain->needs_pr)
enable pri at PCI()
The order here is really important too!
Since PRI can only be supported when a GCR3 is present, this should all be part of some generic 'install GCR3 table DTE' routine that is called on all the attach paths.
Jason
Vasant Hegde
maintainerRe: [PATCH v5 10/14] iommu/amd: Introduce logic to enable/disable IOPF
Quoted 16 lines · Jason Gunthorpe
Quoted 8 lines · Vasant Hegde
Quoted 7 lines · Jason Gunthorpe
Quoted 5 lines · Vasant Hegde
Quoted 4 lines
This dte change is in the wrong place. When the domain is first attached we know if it requires PRI or not. At that moment the DTE should be set properly, it should not be set wrong and then changed later.
Quoted 6 lines
Quoted 3 lines
Quoted 1 line
We want to enable PPR support only after setting up the handler.
That's backwards. It means error handling can't really be sane..
Why do you think enabling feature only when we are really going to use it backwards?
Quoted 7 lines
Because you touch the DTE twice, it means the domain is installed in an inconsistent state where it is not actually working properly. Domain updates should not "tear" like that.
You already know what is going to happen at the very start of attach, you don't need to "enable it after" just do it right the first time through.
First time we will not know whether device will actually use fault handler or not. All we will know is whether IOMMU and device is capable of PRI or not.
We can make assumption that it may use and just enable it.
Quoted 3 lines
There is a clear protocol and ordering requirement for the PRI enablement. Lu described it in a comment, make sure you follow it.
Where? in intel driver? (they seems to be using feature_enable() path)
I did look into latest "iommu: Prepare to deliver page faults to user space" series. I don't see anything specific to PRI enablement flow.
Quoted 3 lines
You also have to think about what happens during detach and what happens on all the pairs of attach -> attach.
ok.
Quoted 9 lines
The error unwinds are tricky, the only way I could make it all be correct for ARM was to fix the attach handling so that there is no failure scenario after the DTE is updated. ie the attach functions either do nothing or fully succeed.
The situation where attach fails and leaves the HW in an unknown state is really hard to deal with - and without the reliable global blocked domain the core code can't 100% rescue it either.
If attach fails we throw error message and skip updating DTE. I believe core layer understands that driver failed to attach device and puts device/group to its original domain. So things should work fine.
Quoted 29 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 3 lines
(and again the whole dte setting flow needs cleaning, I think you should do that before trying to build more complex stuff on top)
Quoted 8 lines
Quoted 6 lines
Quoted 1 line
Yeah. I want to fix few things in that path. But that's outside this series.
I was looking at it and there are many security bugs in here now that iommufd can change the DTE at any time. The current design assumes DMA will be stopped and ignores the spec guidance on how to do a safe DTE update :(
What security issues are you referring? Can you elaborate?
The DTE is not updated correctly. The HW can read inconsistent versions of it with unpredictable - and possibly security bad - results.
Like it doesn't even write the two qwords of the DTE in a predicatble order! Let alone worrying about the 3 qw update or being correct with races during an ITE touch :(
This doesn't matter so much if there is no DMA active while the DTE is being changed, which could sort of reasonably be assumed up till iommufd allowed it to happen under userspace control.
Now a driver cannot make the assumption that DMA is halted. It must follow all the protocols to ensure that HW observes only exactly the DTEs/etc it is trying to build and not something random.
Quoted 7 lines
The documentation is pretty clear how this is supposed to work. It is the same as ARM. Use atomic 64/128 bit stores, rely on 'ignored behavior' or use the valid bit.
This also means, broadly, you can't allow the DTE to evolve during the operation of attach/detach as the in-between states may become userspace visible and may be harmful in some way.
We make DTE changes in set_dte() function only (except dirty bit change that will be consolidated).
Quoted 14 lines
Quoted 10 lines
Quoted 6 lines
I'm really not comfortable with adding more stuff here until the security issue is solved. Especially if the more stuff is drifting further from being correct. If you can keep the updates in
set_dtethen maybe with some reluctance. But not like this with random touches to the DTE all over the place.Currently all DTE update is happening inside
set_dteonly (dirty bit enable is an exception that may need to moved insideset_dte). This patch just invokes thatset_dteand invalidates cache.So then why all this strangeness?? Just set
dev_data->pprearlier in attach and order the handler setup properly.
Quoted 7 lines
It should be really simple:
// All protected by the core's group mutex
if (domain->needs_pri) { dev_data->ppr = true; if (!dev_data->num_pri_domains)
What is PRI domain?
If I have to enable PRI in attach path then I don't need to track number of domain stuff. I can simply do something like
if (pdom_is_sva_capable(pdom)) // enable PRI in IOMMU // enable device PRI
and in detach path,
if (PRI is enabled) // disable IOMMU/device PRI stuff
-Vasant
Quoted 24 lines
// enable fault queues for the device dev_data->num_pri_domains++}
if (old_domain->needs_pri) { dev_data->num_pri_domains--; if (!dev_data->num_pri_domains) { dev_data->ppr = false; disable pri at PCI() }}
set_dte()if (
domain->needs_pr)
enable pri atPCI()The order here is really important too!
Since PRI can only be supported when a GCR3 is present, this should all be part of some generic 'install GCR3 table DTE' routine that is called on all the attach paths.
Jason
Re: [PATCH v5 10/14] iommu/amd: Introduce logic to enable/disable IOPF
Quoted 6 lines · Vasant Hegde
Quoted 2 lines
There is a clear protocol and ordering requirement for the PRI enablement. Lu described it in a comment, make sure you follow it.
Where? in intel driver? (they seems to be using
feature_enable()path)I did look into latest "iommu: Prepare to deliver page faults to user space" series. I don't see anything specific to PRI enablement flow.
The latest version is here.
https://lore.kernel.org/linux-iommu/[email protected]/
Best regards,
baolu
Vasant Hegde
maintainerRe: [PATCH v5 10/14] iommu/amd: Introduce logic to enable/disable IOPF
Baolu,
Quoted 12 lines · Baolu Lu
Quoted 6 lines · Vasant Hegde
Quoted 2 lines
There is a clear protocol and ordering requirement for the PRI enablement. Lu described it in a comment, make sure you follow it.
Where? in intel driver? (they seems to be using
feature_enable()path)I did look into latest "iommu: Prepare to deliver page faults to user space" series. I don't see anything specific to PRI enablement flow.
The latest version is here.
Thanks!
-Vasant
Re: [PATCH v5 10/14] iommu/amd: Introduce logic to enable/disable IOPF
In reply to Vasant HegdeQuoted 6 lines · Vasant Hegde
Quoted 3 lines
You already know what is going to happen at the very start of attach, you don't need to "enable it after" just do it right the first time through.
First time we will not know whether device will actually use fault handler or not. All we will know is whether IOMMU and device is capable of PRI or not.
I don't understand this, you should know all of this before you get to setting the DTE. What is missing?
Quoted 7 lines
Quoted 3 lines
The situation where attach fails and leaves the HW in an unknown state is really hard to deal with - and without the reliable global blocked domain the core code can't 100% rescue it either.
If attach fails we throw error message and skip updating DTE. I believe core layer understands that driver failed to attach device and puts device/group to its original domain. So things should work fine.
It is not just the DTE, the whole thing including changing PCIE config space and so forth has to be kept correct.
Quoted 6 lines
Quoted 3 lines
This also means, broadly, you can't allow the DTE to evolve during the operation of attach/detach as the in-between states may become userspace visible and may be harmful in some way.
We make DTE changes in
set_dte()function only (except dirty bit change that will be consolidated).
Sure, but set_dte doesn't take care to sequence the update.
Quoted 14 lines
Quoted 14 lines
Quoted 8 lines
Quoted 4 lines
security issue is solved. Especially if the more stuff is drifting further from being correct. If you can keep the updates in
set_dtethen maybe with some reluctance. But not like this with random touches to the DTE all over the place.Currently all DTE update is happening inside
set_dteonly (dirty bit enable is an exception that may need to moved insideset_dte). This patch just invokes thatset_dteand invalidates cache.So then why all this strangeness?? Just set
dev_data->pprearlier in attach and order the handler setup properly.It should be really simple:
Quoted 7 lines
Quoted 5 lines
// All protected by the core's group mutex
if (domain->needs_pri) { dev_data->ppr = true; if (!dev_data->num_pri_domains)What is PRI domain?
Right now it is only a SVA domain, it is a domain that wishes to use PRI. Quite soon we are going to expand this to PAGING domains as well.
Quoted 9 lines
If I have to enable PRI in attach path then I don't need to track number of domain stuff. I can simply do something like
if (pdom_is_sva_capable(pdom)) // enable PRI in IOMMU // enable device PRIand in detach path,
if (PRI is enabled) // disable IOMMU/device PRI stuff
Each PASID can have PRI on or not, so you need to keep track of how many PASIDs are using PRI at any moment and keep things in sync that way.
If there are no PRI handlers installed then the PCI config space should disable PRI and all the PRI bits flushed and disabled.
At some point you need to determine if any PASIDs have domains that need PRI. A counter is a simple solution.
Jason
Vasant Hegde
maintainerRe: [PATCH v5 10/14] iommu/amd: Introduce logic to enable/disable IOPF
Jason,
Quoted 11 lines · Jason Gunthorpe
Quoted 6 lines · Vasant Hegde
Quoted 3 lines
You already know what is going to happen at the very start of attach, you don't need to "enable it after" just do it right the first time through.
First time we will not know whether device will actually use fault handler or not. All we will know is whether IOMMU and device is capable of PRI or not.
I don't understand this, you should know all of this before you get to setting the DTE. What is missing?
In attach path we will know the device capabilities (like PRI) but we will not know whether device is going to use it or not. Its like device has capability, let us enable it without assuming device may use it.
IMO enable_feature() was better place as device had a control and we would have enabled only when its needed.
Anyway for now I have moved device PRI and IOPF handler to attach device path. Will try to post it soon.
Quoted 56 lines
Quoted 8 lines
Quoted 4 lines
The situation where attach fails and leaves the HW in an unknown state is really hard to deal with - and without the reliable global blocked domain the core code can't 100% rescue it either.
If attach fails we throw error message and skip updating DTE. I believe core layer understands that driver failed to attach device and puts device/group to its original domain. So things should work fine.
It is not just the DTE, the whole thing including changing PCIE config space and so forth has to be kept correct.
Quoted 6 lines
Quoted 3 lines
This also means, broadly, you can't allow the DTE to evolve during the operation of attach/detach as the in-between states may become userspace visible and may be harmful in some way.
We make DTE changes in
set_dte()function only (except dirty bit change that will be consolidated).Sure, but
set_dtedoesn't take care to sequence the update.Quoted 14 lines
Quoted 14 lines
Quoted 8 lines
Quoted 4 lines
security issue is solved. Especially if the more stuff is drifting further from being correct. If you can keep the updates in
set_dtethen maybe with some reluctance. But not like this with random touches to the DTE all over the place.Currently all DTE update is happening inside
set_dteonly (dirty bit enable is an exception that may need to moved insideset_dte). This patch just invokes thatset_dteand invalidates cache.So then why all this strangeness?? Just set
dev_data->pprearlier in attach and order the handler setup properly.It should be really simple:
Quoted 7 lines
Quoted 5 lines
// All protected by the core's group mutex
if (domain->needs_pri) { dev_data->ppr = true; if (!dev_data->num_pri_domains)What is PRI domain?
Right now it is only a SVA domain, it is a domain that wishes to use PRI. Quite soon we are going to expand this to PAGING domains as well.
Quoted 9 lines
If I have to enable PRI in attach path then I don't need to track number of domain stuff. I can simply do something like
if (pdom_is_sva_capable(pdom)) // enable PRI in IOMMU // enable device PRIand in detach path,
if (PRI is enabled) // disable IOMMU/device PRI stuff
Quoted 6 lines
Each PASID can have PRI on or not, so you need to keep track of how many PASIDs are using PRI at any moment and keep things in sync that way.
If there are no PRI handlers installed then the PCI config space should disable PRI and all the PRI bits flushed and disabled.
If we don't have handler then PRI is disabled in attach device path only.
So in detach path, if number of PASIDs are zero then we are good to disable PRI (at least for the current usage model).
Quoted 3 lines
At some point you need to determine if any PASIDs have domains that need PRI. A counter is a simple solution.
That we can implement it as use case evolves.
-Vasant
Re: [PATCH v5 10/14] iommu/amd: Introduce logic to enable/disable IOPF
Quoted 10 lines · Vasant Hegde
Quoted 9 lines · Jason Gunthorpe
Quoted 6 lines · Vasant Hegde
Quoted 3 lines
You already know what is going to happen at the very start of attach, you don't need to "enable it after" just do it right the first time through.
First time we will not know whether device will actually use fault handler or not. All we will know is whether IOMMU and device is capable of PRI or not.
Quoted 6 lines
Quoted 2 lines
I don't understand this, you should know all of this before you get to setting the DTE. What is missing?
In attach path we will know the device capabilities (like PRI) but we will not know whether device is going to use it or not. Its like device has capability, let us enable it without assuming device may use it.
I don't understand "device may use it"
At domain pasid attach time you have the domain being attached and information the device capabilities.
The decision is simple, if the domain is using PRI and the device supports PRI you enable PRI.
This means you enable PRI when you attach the first PRI domain to the GCR3, which will require rewriting the DTE during set_dev_pasid.
This is part of the same logical flow where you'd rewrite the DTE during set_dev_pasid to do things like IDENTITY and BLOCKING RID support.
Quoted 14 lines
Quoted 14 lines
Quoted 9 lines
If I have to enable PRI in attach path then I don't need to track number of domain stuff. I can simply do something like
if (pdom_is_sva_capable(pdom)) // enable PRI in IOMMU // enable device PRIand in detach path,
if (PRI is enabled) // disable IOMMU/device PRI stuffEach PASID can have PRI on or not, so you need to keep track of how many PASIDs are using PRI at any moment and keep things in sync that way.
Quoted 7 lines
Quoted 2 lines
If there are no PRI handlers installed then the PCI config space should disable PRI and all the PRI bits flushed and disabled.
If we don't have handler then PRI is disabled in attach device path only.
So in detach path, if number of PASIDs are zero then we are good to disable PRI (at least for the current usage model).
So this is why you are having the problem above, the PRI logic should not be in the attach_dev path because that does not take in a PRI capable domaine (currently only SVA)
It should be triggered in set_dev_pasid and remove_dev_pasid.
I'm trying to get you to organize things so they are ready for the next steps and things are not in the wrong spot.
Jason
Vasant Hegde
maintainerPATCH v5 11/14 iommu/amd: Add GCR3 [un]initialization function
In reply to Vasant HegdeFrom: Suravee Suthikulpanit <[email protected]>
These functions are used in PASID to device bind path. In this path it checks whether device GCR3 table is setup or not. If not it will setup GCR3 table.
Also in attach device path change default GCR3 table to use MAX supported PASIDs. Ideally it should use 1 level PASID table as its using PASID zero only. But we don't have support to extend PASID table yet. We will fix this later.
--- drivers/iommu/amd/amd_iommu.h | 3 ++ drivers/iommu/amd/iommu.c | 52 +++++++++++++++++++++++++++++++++-- 2 files changed, 53 insertions(+), 2 deletions(-)
drivers/iommu/amd/amd_iommu.h +3 -0
@@ -44,7 +44,10 @@ extern int amd_iommu_guest_ir;extern enum io_pgtable_fmt amd_iommu_pgtable;extern int amd_iommu_gpt_level; +/* SVA/PASID */ bool amd_iommu_pasid_supported (void ); +int amd_iommu_gcr3_init (struct iommu_dev_data *dev_data,ioasid_t pasids); +void amd_iommu_gcr3_uninit (struct iommu_dev_data *dev_data);/* IOPF */ int amd_iommu_iopf_init (struct amd_iommu *iommu);
drivers/iommu/amd/iommu.c +50 -2
71 lines not on this page · raw message
Signature · 1 line
2.31.1
Re: [PATCH v5 11/14] iommu/amd: Add GCR3 [un]initialization function
Quoted 39 lines · Vasant Hegde
From: Suravee Suthikulpanit <[email protected]>
These functions are used in PASID to device bind path. In this path it checks whether device GCR3 table is setup or not. If not it will setup GCR3 table.
Also in attach device path change default GCR3 table to use MAX supported PASIDs. Ideally it should use 1 level PASID table as its using PASID zero only. But we don't have support to extend PASID table yet. We will fix this later.
Signed-off-by Suravee Suthikulpanit <[email protected]>Co-developed-by Vasant Hegde <[email protected]>Signed-off-by Vasant Hegde <[email protected]>--- drivers/iommu/amd/amd_iommu.h | 3 ++ drivers/iommu/amd/iommu.c | 52 +++++++++++++++++++++++++++++++++-- 2 files changed, 53 insertions(+), 2 deletions(-)drivers/iommu/amd/amd_iommu.h +3
-0@@ -44,7 +44,10 @@ extern int amd_iommu_guest_ir;extern enum io_pgtable_fmt amd_iommu_pgtable;extern int amd_iommu_gpt_level; +/* SVA/PASID */ bool amd_iommu_pasid_supported (void ); +int amd_iommu_gcr3_init (struct iommu_dev_data *dev_data,ioasid_t pasids); +void amd_iommu_gcr3_uninit (struct iommu_dev_data *dev_data);/* IOPF */ int amd_iommu_iopf_init (struct amd_iommu *iommu);drivers/iommu/amd/iommu.c +0
-0
drivers/iommu/amd/iommu.c static inline bool pdom_is_v2_pgtbl_mode(struct protection_domain *pdom) · line 99
Quoted 7 lines
drivers/iommu/amd/iommu.c +4
-0@@ -93,6 +93,11 @@ static inline bool pdom_is_v2_pgtbl_mode(struct protection_domain *pdom)return (pdom && (pdom->pd_mode ==PD_MODE_V2 )); } +static inline bool pdom_is_in_pt_mode (struct protection_domain *pdom) +{ +return (pdom->domain.type ==IOMMU_DOMAIN_IDENTITY ); +}
Why? And what about blocking someday?
Just use dev_data->gcr3_info.gcr3_tbl == NULL to indicate if GCR3 is loaded or not?
Quoted 11 lines
drivers/iommu/amd/iommu.c +4
-0/* * Allocate per device domain ID when using V2 page table */ @@ -1837,6 +1842,46 @@ int amd_iommu_clear_gcr3(struct iommu_dev_data *dev_data, ioasid_t pasid)return ret; } +int amd_iommu_gcr3_init (struct iommu_dev_data *dev_data,ioasid_t pasids) +{ +struct protection_domain *pdom = dev_data->domain; +int ret =0 ;
drivers/iommu/amd/iommu.c int amd_iommu_clear_gcr3(struct iommu_dev_data *dev_data, ioasid_t pasid) · line 1858
Quoted 10 lines
drivers/iommu/amd/iommu.c +10
-0+ +lockdep_assert_held (&dev_data->lock); + +/* +* We cannot support PASID w/ existing v1 page table in the same domain +* since it will be nested. However, existing domain w/ v2 page table +* can be used for PASID. +*/ +if (!pdom_is_v2_pgtbl_mode (pdom) && !pdom_is_in_pt_mode (pdom)) +return -EOPNOTSUPP ;
Put the test directly in the set dev pasid op and it should be more like
if (!dev_data->gcr3_info.gcr3_tbl && dev_data->domain->type & _IOMMU_DOMAIN_PAGING)
return -EINVAL;
And you need the mirroring test in alloc_dev to prevent changing the RID to things the driver does not yet support, I didn't notice that?
drivers/iommu/amd/iommu.c int amd_iommu_clear_gcr3(struct iommu_dev_data *dev_data, ioasid_t pasid) · line 1867
Quoted 8 lines
drivers/iommu/amd/iommu.c +8
-0+/* Allocate GCR3 table */ +if (pdom_is_in_pt_mode (pdom) && dev_data->gcr3_info.gcr3_tbl ==NULL ) { + ret =setup_gcr3_table (&dev_data->gcr3_info, +dev_to_node (dev_data->dev), pasids); + +/* Update device table */ +amd_iommu_dev_update_dte (dev_data, true); + }
This shouldn't be any different from do_attach()
drivers/iommu/amd/iommu.c int amd_iommu_clear_gcr3(struct iommu_dev_data *dev_data, ioasid_t pasid) · line 1868
Quoted 2 lines
drivers/iommu/amd/iommu.c +2
-0+ +return ret;
success oritened flow please
drivers/iommu/amd/iommu.c int amd_iommu_clear_gcr3(struct iommu_dev_data *dev_data, ioasid_t pasid) · line 1883
Quoted 12 lines
drivers/iommu/amd/iommu.c +12
-0+void amd_iommu_gcr3_uninit (struct iommu_dev_data *dev_data) +{ +lockdep_assert_held (&dev_data->lock); + +/* Free GCR3 table */ +if (pdom_is_in_pt_mode (dev_data->domain)) { +free_gcr3_table (&dev_data->gcr3_info); + +/* Update device table */ +amd_iommu_dev_update_dte (dev_data, true); + } +}
Is it really worth freeing it?
Quoted 5 lines
drivers/iommu/amd/iommu.c +0
-0static void set_dte_entry (struct amd_iommu *iommu,struct iommu_dev_data *dev_data) {@@ -1986,9 +2031,12 @@ static int do_attach(struct iommu_dev_data *dev_data,
drivers/iommu/amd/iommu.c static int do_attach(struct iommu_dev_data *dev_data, · line 2039
Quoted 10 lines
drivers/iommu/amd/iommu.c +5
-2/* Init GCR3 table and update device table */ if (domain->pd_mode ==PD_MODE_V2 ) { -/* By default, setup GCR3 table to support single PASID */ +/* +* By default, setup GCR3 table to support MAX PASIDs +* supported by the IOMMU HW. +*/ ret =setup_gcr3_table (&dev_data->gcr3_info, -dev_to_node (dev_data->dev),1 ); +dev_to_node (dev_data->dev),-1 );
-1 should be dev->iommu->max_pasids, but better would be this specific device's max pasid size, cached from pci_max_pasids()
Jason
Vasant Hegde
maintainerRe: [PATCH v5 11/14] iommu/amd: Add GCR3 [un]initialization function
Jason,
Quoted 43 lines · Jason Gunthorpe
Quoted 42 lines · Vasant Hegde
From: Suravee Suthikulpanit <[email protected]>
These functions are used in PASID to device bind path. In this path it checks whether device GCR3 table is setup or not. If not it will setup GCR3 table.
Also in attach device path change default GCR3 table to use MAX supported PASIDs. Ideally it should use 1 level PASID table as its using PASID zero only. But we don't have support to extend PASID table yet. We will fix this later.
Signed-off-by Suravee Suthikulpanit <[email protected]>Co-developed-by Vasant Hegde <[email protected]>Signed-off-by Vasant Hegde <[email protected]>--- drivers/iommu/amd/amd_iommu.h | 3 ++ drivers/iommu/amd/iommu.c | 52 +++++++++++++++++++++++++++++++++-- 2 files changed, 53 insertions(+), 2 deletions(-)drivers/iommu/amd/amd_iommu.h +3
-0@@ -44,7 +44,10 @@ extern int amd_iommu_guest_ir;extern enum io_pgtable_fmt amd_iommu_pgtable;extern int amd_iommu_gpt_level; +/* SVA/PASID */ bool amd_iommu_pasid_supported (void ); +int amd_iommu_gcr3_init (struct iommu_dev_data *dev_data,ioasid_t pasids); +void amd_iommu_gcr3_uninit (struct iommu_dev_data *dev_data);/* IOPF */ int amd_iommu_iopf_init (struct amd_iommu *iommu);drivers/iommu/amd/iommu.c +0
-0@@ -93,6 +93,11 @@ static inline bool pdom_is_v2_pgtbl_mode(struct protection_domain *pdom)return (pdom && (pdom->pd_mode ==PD_MODE_V2 )); }
Quoted 6 lines
drivers/iommu/amd/iommu.c static inline bool pdom_is_v2_pgtbl_mode(struct protection_domain *pdom) · line 99
Quoted 4 lines
drivers/iommu/amd/iommu.c +4
-0+static inline bool pdom_is_in_pt_mode (struct protection_domain *pdom) +{ +return (pdom->domain.type ==IOMMU_DOMAIN_IDENTITY ); +}Why? And what about blocking someday?
Today model allocates GCR3 if its in PT mode only. If we support PASID with BLOCKing domain then I will add that support.
Quoted 3 lines
Just use
dev_data->gcr3_info.gcr3_tbl== NULL to indicate if GCR3 is loaded or not?
Given number of combination (like v2, v1, pt) above check is not sufficient.
Quoted 26 lines
Quoted 12 lines
drivers/iommu/amd/iommu.c +4
-0/* * Allocate per device domain ID when using V2 page table */ @@ -1837,6 +1842,46 @@ int amd_iommu_clear_gcr3(struct iommu_dev_data *dev_data, ioasid_t pasid)return ret; } +int amd_iommu_gcr3_init (struct iommu_dev_data *dev_data,ioasid_t pasids) +{ +struct protection_domain *pdom = dev_data->domain; +int ret =0 ;drivers/iommu/amd/iommu.c int amd_iommu_clear_gcr3(struct iommu_dev_data *dev_data, ioasid_t pasid) · line 1858
Quoted 10 lines
drivers/iommu/amd/iommu.c +10
-0+ +lockdep_assert_held (&dev_data->lock); + +/* +* We cannot support PASID w/ existing v1 page table in the same domain +* since it will be nested. However, existing domain w/ v2 page table +* can be used for PASID. +*/ +if (!pdom_is_v2_pgtbl_mode (pdom) && !pdom_is_in_pt_mode (pdom)) +return -EOPNOTSUPP ;Put the test directly in the set dev pasid op and it should be more like
Quoted 2 lines
if (!dev_data->gcr3_info.gcr3_tbl &&
dev_data->domain->type&_IOMMU_DOMAIN_PAGING)return -EINVAL;
I don't think that's right place. sev_dev pasid doesn't need to know all domain combination, setting up gcr3 table, etc.
Quoted 4 lines
And you need the mirroring test in
alloc_devto prevent changing the RID to things the driver does not yet support, I didn't notice that?
You mean attach_dev() path?
Quoted 11 lines
drivers/iommu/amd/iommu.c int amd_iommu_clear_gcr3(struct iommu_dev_data *dev_data, ioasid_t pasid) · line 1867
Quoted 9 lines
drivers/iommu/amd/iommu.c +8
-0+/* Allocate GCR3 table */ +if (pdom_is_in_pt_mode (pdom) && dev_data->gcr3_info.gcr3_tbl ==NULL ) { + ret =setup_gcr3_table (&dev_data->gcr3_info, +dev_to_node (dev_data->dev), pasids); + +/* Update device table */ +amd_iommu_dev_update_dte (dev_data, true); + }This shouldn't be any different from
do_attach()
We have allocated new GCR3 table and DTE needs to be updated.
Quoted 5 lines
drivers/iommu/amd/iommu.c int amd_iommu_clear_gcr3(struct iommu_dev_data *dev_data, ioasid_t pasid) · line 1868
Quoted 3 lines
drivers/iommu/amd/iommu.c +2
-0+ +return ret;success oritened flow please
Ok.
Quoted 15 lines
drivers/iommu/amd/iommu.c int amd_iommu_clear_gcr3(struct iommu_dev_data *dev_data, ioasid_t pasid) · line 1883
Quoted 13 lines
drivers/iommu/amd/iommu.c +12
-0+void amd_iommu_gcr3_uninit (struct iommu_dev_data *dev_data) +{ +lockdep_assert_held (&dev_data->lock); + +/* Free GCR3 table */ +if (pdom_is_in_pt_mode (dev_data->domain)) { +free_gcr3_table (&dev_data->gcr3_info); + +/* Update device table */ +amd_iommu_dev_update_dte (dev_data, true); + } +}Is it really worth freeing it?
Why not? But I don't like the domain ID changes every time. So may be OK to drop the uninit. Will look into it.
Quoted 6 lines
Quoted 6 lines
drivers/iommu/amd/iommu.c +0
-0static void set_dte_entry (struct amd_iommu *iommu,struct iommu_dev_data *dev_data) {@@ -1986,9 +2031,12 @@ static int do_attach(struct iommu_dev_data *dev_data,
Quoted 13 lines
drivers/iommu/amd/iommu.c static int do_attach(struct iommu_dev_data *dev_data, · line 2039
Quoted 10 lines
drivers/iommu/amd/iommu.c +5
-2/* Init GCR3 table and update device table */ if (domain->pd_mode ==PD_MODE_V2 ) { -/* By default, setup GCR3 table to support single PASID */ +/* +* By default, setup GCR3 table to support MAX PASIDs +* supported by the IOMMU HW. +*/ ret =setup_gcr3_table (&dev_data->gcr3_info, -dev_to_node (dev_data->dev),1 ); +dev_to_node (dev_data->dev),-1 );-1 should be
dev->iommu->max_pasids, but better would be this specific device's max pasid size, cached frompci_max_pasids()
Ok will fix it.
-Vasant
Vasant Hegde
maintainerPATCH v5 12/14 iommu/amd: Initial SVA support for AMD IOMMU
In reply to Vasant HegdeThis includes :
- Add data structure to track per protection domain dev/pasid binding details
protection_domain->dev_data_list will track attached list of
dev_data/PASIDs.- Add support to check PASID is supported or not. Also setup gcr3 table and if PRI is supported then enable IOPF.
- Move 'to_pdomain()' to header file
- Add iommu_sva_set_dev_pasid(). It will check whether PASID is supported or not. Also adds PASID to SVA protection domain list as well as to device GCR3 table.
- Add iommu_ops.remove_dev_pasid support. It will unbind PASID from device. Also remove pasid data from protection domain.
- Add IOMMU_SVA as dependency to AMD_IOMMU driver
For a given PASID, iommu_set_dev_pasid() will bind all devices to same SVA protection domain (1 PASID : 1 SVA protection domain : N devices). This protection domain is different from device protection domain (one that's mapped in attach_device() path). IOMMU uses domain ID for caching, invalidation, etc. In SVA mode it will use per-device-domain-ID. Hence in invalidation path we retrieve domain ID from gcr3_info_table structure and use that for invalidation.
--- drivers/iommu/amd/Kconfig | 1 + drivers/iommu/amd/Makefile | 2 +- drivers/iommu/amd/amd_iommu.h | 11 ++ drivers/iommu/amd/amd_iommu_types.h | 19 +++ drivers/iommu/amd/iommu.c | 14 +- drivers/iommu/amd/pasid.c | 191 ++++++++++++++++++++++++++++ 6 files changed, 232 insertions(+), 6 deletions(-) create mode 100644 drivers/iommu/amd/pasid.c
drivers/iommu/amd/Kconfig +1 -0
@@ -10,6 +10,7 @@ config AMD_IOMMU select IOMMU_API select IOMMU_IOVA select IOMMU_IO_PGTABLE + select IOMMU_SVA select IOMMU_IOPF select IOMMUFD_DRIVER if IOMMUFD depends on X86_64 && PCI && ACPI && HAVE_CMPXCHG_DOUBLE
drivers/iommu/amd/Makefile +1 -1
@@ -1,3 +1,3 @@ # SPDX-License-Identifier: GPL-2.0-only -obj-$(CONFIG_AMD_IOMMU) += iommu.o init.o quirks.o io_pgtable.o io_pgtable_v2.o ppr.o +obj-$(CONFIG_AMD_IOMMU) += iommu.o init.o quirks.o io_pgtable.o io_pgtable_v2.o ppr.o pasid.o obj-$(CONFIG_AMD_IOMMU_DEBUGFS) += debugfs.o
drivers/iommu/amd/amd_iommu.h +11 -0
@@ -44,6 +44,11 @@ extern int amd_iommu_guest_ir;extern enum io_pgtable_fmt amd_iommu_pgtable;extern int amd_iommu_gpt_level; +/* Protection domain ops */ +int iommu_sva_set_dev_pasid (struct iommu_domain *domain, +struct device *dev,ioasid_t pasid); +void amd_iommu_remove_dev_pasid (struct device *dev,ioasid_t pasid); +/* SVA/PASID */ bool amd_iommu_pasid_supported (void );int amd_iommu_gcr3_init (struct iommu_dev_data *dev_data,ioasid_t pasids);
@@ -72,6 +77,7 @@ int amd_iommu_pc_set_reg(struct amd_iommu *iommu, u8 bank, u8 cntr,/* Device capabilities */ int amd_iommu_pdev_enable_cap_pri (struct pci_dev *pdev);void amd_iommu_pdev_disable_cap_pri (struct pci_dev *pdev); +bool amd_iommu_pdev_pri_supported (struct pci_dev *pdev);/* GCR3 setup */ int amd_iommu_set_gcr3(struct iommu_dev_data *dev_data,
@@ -196,6 +202,11 @@ static inline struct amd_iommu *get_amd_iommu_from_dev_data(struct iommu_dev_dat return iommu_get_iommu_dev(dev_data->dev, struct amd_iommu, iommu); } +static inline struct protection_domain *to_pdomain (struct iommu_domain *dom) +{ + return container_of(dom, struct protection_domain, domain); +} +bool translation_pre_enabled (struct amd_iommu *iommu);bool amd_iommu_is_attach_deferred (struct device *dev);int __init add_special_device (u8 type,u8 id,u32 *devid,bool cmd_line);
drivers/iommu/amd/amd_iommu_types.h +19 -0
@@ -8,7 +8,9 @@#ifndef _ASM_X86_AMD_IOMMU_TYPES_H#define _ASM_X86_AMD_IOMMU_TYPES_H +#include <linux/iommu.h> #include <linux/types.h> +#include <linux/mmu_notifier.h> #include <linux/mutex.h> #include <linux/msi.h> #include <linux/list.h>
@@ -511,6 +513,11 @@ extern struct kmem_cache *amd_iommu_irq_cache; list_for_each_entry((iommu), &amd_iommu_list, list)#define for_each_iommu_safe (iommu, next) \ list_for_each_entry_safe((iommu), (next), &amd_iommu_list, list) +/* Making iterating over protection_domain->dev_data_list easier */ +#define for_each_pdom_dev_data (pdom_dev_data, pdom) \ + list_for_each_entry(pdom_dev_data, &pdom->dev_data_list, list) +#define for_each_pdom_dev_data_safe (pdom_dev_data, next, pdom) \ + list_for_each_entry_safe((pdom_dev_data), (next), &pdom->dev_data_list, list)#define APERTURE_RANGE_SHIFT 27/* 128 MB */ #define APERTURE_RANGE_SIZE (1ULL << APERTURE_RANGE_SHIFT)
@@ -560,6 +567,16 @@ enum protection_domain_mode { PD_MODE_V2, }; +/* Track dev_data/PASID list for the protection domain */ +struct pdom_dev_data { +/* Points to attached device data */ +struct iommu_dev_data *dev_data; +/* PASID attached to the protection domain */ +ioasid_t pasid; +/* For protection_domain->dev_data_list */ +struct list_head list; +}; +/* * This structure contains generic data for IOMMU protection domains * independent of their use.
@@ -576,6 +593,8 @@ struct protection_domain {bool dirty_tracking;/* dirty tracking is enabled in the domain */ unsigned dev_cnt;/* devices assigned to this domain */ unsigned dev_iommu[MAX_IOMMUS ];/* per-IOMMU reference count */ + +struct list_head dev_data_list;/* List of pdom_dev_data */ };/*
drivers/iommu/amd/iommu.c +9 -5
@@ -196,11 +196,6 @@ static struct amd_iommu *rlookup_amd_iommu(struct device *dev)return __rlookup_amd_iommu (seg,PCI_SBDF_TO_DEVID (devid)); } -static struct protection_domain *to_pdomain (struct iommu_domain *dom) -{ - return container_of(dom, struct protection_domain, domain); -} -static struct iommu_dev_data *alloc_dev_data (struct amd_iommu *iommu,u16 devid) {struct iommu_dev_data *dev_data;
@@ -346,6 +341,13 @@ static inline bool pdev_pasid_supported(struct iommu_dev_data *dev_data)return (dev_data->flags &AMD_IOMMU_DEVICE_FLAG_PASID_SUP ); } +inline bool amd_iommu_pdev_pri_supported (struct pci_dev *pdev) +{ +struct iommu_dev_data *dev_data =dev_iommu_priv_get (&pdev->dev); + +return (dev_data->flags &AMD_IOMMU_DEVICE_FLAG_PRI_SUP ); +} +static u32 pdev_get_caps (struct pci_dev *pdev) {int features;
@@ -2309,6 +2311,7 @@ static struct protection_domain *protection_domain_alloc(unsigned int type)spin_lock_init (&domain->lock);INIT_LIST_HEAD (&domain->dev_list); +INIT_LIST_HEAD (&domain->dev_data_list); domain->nid =NUMA_NO_NODE ;switch (type) {
@@ -2838,6 +2841,7 @@ const struct iommu_ops amd_iommu_ops = { .def_domain_type = amd_iommu_def_domain_type, .dev_enable_feat = amd_iommu_dev_enable_feature, .dev_disable_feat = amd_iommu_dev_disable_feature, + .remove_dev_pasid = amd_iommu_remove_dev_pasid, .page_response = amd_iommu_page_response, .default_domain_ops = &(const struct iommu_domain_ops ) { .attach_dev = amd_iommu_attach_device,
drivers/iommu/amd/pasid.c new file +191 -0
191 lines not on this page · raw message
Signature · 1 line
2.31.1
Re: [PATCH v5 12/14] iommu/amd: Initial SVA support for AMD IOMMU
Quoted 7 lines · Vasant Hegde
drivers/iommu/amd/pasid.c new file +7
-0+static int iommu_pasid_enable (struct iommu_dev_data *dev_data) +{ +struct device *dev = dev_data->dev; +int ret =0 ; + +spin_lock (&dev_data->lock); +
drivers/iommu/amd/pasid.c line 45
Quoted 10 lines
drivers/iommu/amd/pasid.c new file +10
-0+if (is_pasid_enabled (dev_data)) + goto out; + +if (!amd_iommu_pasid_supported ()) { + ret = -ENODEV ; + goto out; + } + +/* attach_device path enables device PASID feature */ +if (!dev_data->pasid_enabled) {
How many times are we testing for this? Just check if the gcr3 table is installed once
drivers/iommu/amd/pasid.c line 55
Quoted 10 lines
drivers/iommu/amd/pasid.c new file +10
-0+ ret = -EINVAL ; + goto out; + } + + ret =amd_iommu_gcr3_init (dev_data, dev->iommu->max_pasids); + +out: +spin_unlock (&dev_data->lock); +return ret; +}
This seems like too much, and it doesn't need to be in a function..
1) Check directly if the gcr3 table is installed otherwise try to install it. That might be a usefull function
2) Precompute the max pasids during device probe and store it in iommu_dev_data. Just check if PASID >= max_pasid and fail
drivers/iommu/amd/pasid.c line 62
Quoted 6 lines
drivers/iommu/amd/pasid.c new file +6
-0+static void iommu_pasid_disable (struct iommu_dev_data *dev_data) +{ +spin_lock (&dev_data->lock); + +if (!is_gcr3_table_empty (dev_data)) + goto out;
Caller already checked this
drivers/iommu/amd/pasid.c line 65
Quoted 3 lines
drivers/iommu/amd/pasid.c new file +3
-0+ +if (dev_data->gcr3_info.gcr3_tbl ==NULL ) + goto out;
Can't happen, right?
Review
Quoted 2 lines
(quoted diff) +2
-0+ + amd_iommu_gcr3_uninit(dev_data);
Just write it out clearly in remove dev pasid
if (is_gcr3_table_empty(dev_data))
amd_iommu_gcr3_uninit(dev_data);
Quoted 18 lines
drivers/iommu/amd/pasid.c new file +18
-0+static int iommu_setup_pasid_pri (struct iommu_dev_data *dev_data) +{ +struct pci_dev *pdev; +int ret; + +if (is_pasid_enabled (dev_data)) +return 0 ; + + ret =iommu_pasid_enable (dev_data); +if (ret) +return ret; + + pdev =dev_is_pci (dev_data->dev) ?to_pci_dev (dev_data->dev) :NULL ; +if (!pdev || !amd_iommu_pdev_pri_supported (pdev)) +return 0 ; + +if (!dev_data->pri_enabled) +return -EINVAL ;
drivers/iommu/amd/pasid.c line 100
Quoted 10 lines
drivers/iommu/amd/pasid.c new file +10
-0+ + ret =amd_iommu_iopf_enable_device (dev_data->dev); + +return ret; +} + +static void remove_dev_pasid (struct pdom_dev_data *pdom_dev_data) +{ +/* Update GCR3 table and flush IOTLB */ +amd_iommu_clear_gcr3 (pdom_dev_data->dev_data, pdom_dev_data->pasid);
This is in the wrong place, there is only one DTE/GCR3 remove_dev is touching. The list iteration below is just to clean up the tracking list it should not touch HW. Move this up into amd_iommu_remove_dev_pasid.
And these functions related to the tracking list should be more general and called in more places. Just the tracking list itself should have a few patches to create it and situate it generically in the driver. Even the RID should be using the same mechanism.
Quoted 27 lines
drivers/iommu/amd/pasid.c new file +27
-0+int iommu_sva_set_dev_pasid (struct iommu_domain *domain, +struct device *dev,ioasid_t pasid) +{ +struct pdom_dev_data *pdom_dev_data; +struct protection_domain *sva_pdom =to_pdomain (domain); +struct iommu_dev_data *dev_data =dev_iommu_priv_get (dev); +unsigned long flags; +int ret = -EINVAL ; + +/* PASID zero is used for requests from the I/O device without PASID */ +if (pasid ==0 || pasid >= dev->iommu->max_pasids) +return ret; + +/* Make sure PASID/PRI is enabled */ + ret =iommu_setup_pasid_pri (dev_data); +if (ret) +return ret; + +/* Add PASID to protection domain pasid list */ + pdom_dev_data =kzalloc (sizeof (*pdom_dev_data),GFP_KERNEL ); +if (pdom_dev_data ==NULL ) +return ret; + + pdom_dev_data->pasid = pasid; + pdom_dev_data->dev_data = dev_data; + +/* Setup GCR3 table */
drivers/iommu/amd/pasid.c line 160
Quoted 10 lines
drivers/iommu/amd/pasid.c new file +10
-0+ ret =amd_iommu_set_gcr3 (dev_data, pasid, +iommu_virt_to_phys (domain->mm->pgd)); +if (ret) { +kfree (pdom_dev_data); +return ret; + } + +spin_lock_irqsave (&sva_pdom->lock, flags); +list_add (&pdom_dev_data->list, &sva_pdom->dev_data_list); +spin_unlock_irqrestore (&sva_pdom->lock, flags);
This doesn't seem right? The tracking list should be loaded before any change is made visible to the HW, or at least under the same lock.
Jason
Vasant Hegde
maintainerRe: [PATCH v5 12/14] iommu/amd: Initial SVA support for AMD IOMMU
Jason,
Quoted 14 lines · Jason Gunthorpe
Quoted 12 lines · Vasant Hegde
drivers/iommu/amd/pasid.c new file +12
-0+static int iommu_pasid_enable (struct iommu_dev_data *dev_data) +{ +struct device *dev = dev_data->dev; +int ret =0 ; + +spin_lock (&dev_data->lock); + +if (is_pasid_enabled (dev_data)) + goto out; + +if (!amd_iommu_pasid_supported ()) { + ret = -ENODEV ;
Quoted 8 lines
drivers/iommu/amd/pasid.c line 45
Quoted 5 lines
drivers/iommu/amd/pasid.c new file +5
-0+ goto out; + } + +/* attach_device path enables device PASID feature */ +if (!dev_data->pasid_enabled) {How many times are we testing for this? Just check if the gcr3 table is installed once
One time for IOMMU capability (amd_iommu_pasid_supported()) and one time for device capability.
is_pasid_enabled() is checked twice (once without lock, so that we can avoid lock in most cases and one inside lock to be sure no one else entered and enabled gcr3).
Quoted 14 lines
drivers/iommu/amd/pasid.c line 55
Quoted 11 lines
drivers/iommu/amd/pasid.c new file +10
-0+ ret = -EINVAL ; + goto out; + } + + ret =amd_iommu_gcr3_init (dev_data, dev->iommu->max_pasids); + +out: +spin_unlock (&dev_data->lock); +return ret; +}This seems like too much, and it doesn't need to be in a function..
Quoted 2 lines
1) Check directly if the gcr3 table is installed otherwise try to install it. That might be a usefull function
We need other checks to make sure both IOMMU and device is capable of PASID. Hence its a separate function.
Quoted 3 lines
2) Precompute the max pasids during device probe and store it in
iommu_dev_data. Just check if PASID >=max_pasidand fail
This is not required .. as set_dev_pasid() can directly check dev->iommu->max_pasids.
Quoted 9 lines
drivers/iommu/amd/pasid.c line 62
Quoted 7 lines
drivers/iommu/amd/pasid.c new file +6
-0+static void iommu_pasid_disable (struct iommu_dev_data *dev_data) +{ +spin_lock (&dev_data->lock); + +if (!is_gcr3_table_empty (dev_data)) + goto out;Caller already checked this
Yes. Will drop this check.
Quoted 6 lines
drivers/iommu/amd/pasid.c line 65
Quoted 4 lines
drivers/iommu/amd/pasid.c new file +3
-0+ +if (dev_data->gcr3_info.gcr3_tbl ==NULL ) + goto out;Can't happen, right?
Yes. Will drop.
Quoted 9 lines
Review
Quoted 3 lines
(quoted diff) +2
-0+ + amd_iommu_gcr3_uninit(dev_data);Just write it out clearly in remove dev pasid
if (
is_gcr3_table_empty(dev_data))
amd_iommu_gcr3_uninit(dev_data);
Ok.
Quoted 25 lines
Quoted 25 lines
drivers/iommu/amd/pasid.c new file +25
-0+static int iommu_setup_pasid_pri (struct iommu_dev_data *dev_data) +{ +struct pci_dev *pdev; +int ret; + +if (is_pasid_enabled (dev_data)) +return 0 ; + + ret =iommu_pasid_enable (dev_data); +if (ret) +return ret; + + pdev =dev_is_pci (dev_data->dev) ?to_pci_dev (dev_data->dev) :NULL ; +if (!pdev || !amd_iommu_pdev_pri_supported (pdev)) +return 0 ; + +if (!dev_data->pri_enabled) +return -EINVAL ; + + ret =amd_iommu_iopf_enable_device (dev_data->dev); + +return ret; +} + +static void remove_dev_pasid (struct pdom_dev_data *pdom_dev_data)
Quoted 8 lines
drivers/iommu/amd/pasid.c line 100
Quoted 3 lines
drivers/iommu/amd/pasid.c new file +3
-0+{ +/* Update GCR3 table and flush IOTLB */ +amd_iommu_clear_gcr3 (pdom_dev_data->dev_data, pdom_dev_data->pasid);This is in the wrong place, there is only one DTE/GCR3
remove_devis touching. The list iteration below is just to clean up the tracking list it should not touch HW. Move this up intoamd_iommu_remove_dev_pasid.
This is used in remove_dev_pasid and sva_mn_release path.
This just clears GCR3[pasid] entry. Its not updating DTE.
Quoted 5 lines
And these functions related to the tracking list should be more general and called in more places. Just the tracking list itself should have a few patches to create it and situate it generically in the driver. Even the RID should be using the same mechanism.
That's after reworking protection domain structure. Not in this series.
Quoted 33 lines
Quoted 33 lines
drivers/iommu/amd/pasid.c new file +32
-0+int iommu_sva_set_dev_pasid (struct iommu_domain *domain, +struct device *dev,ioasid_t pasid) +{ +struct pdom_dev_data *pdom_dev_data; +struct protection_domain *sva_pdom =to_pdomain (domain); +struct iommu_dev_data *dev_data =dev_iommu_priv_get (dev); +unsigned long flags; +int ret = -EINVAL ; + +/* PASID zero is used for requests from the I/O device without PASID */ +if (pasid ==0 || pasid >= dev->iommu->max_pasids) +return ret; + +/* Make sure PASID/PRI is enabled */ + ret =iommu_setup_pasid_pri (dev_data); +if (ret) +return ret; + +/* Add PASID to protection domain pasid list */ + pdom_dev_data =kzalloc (sizeof (*pdom_dev_data),GFP_KERNEL ); +if (pdom_dev_data ==NULL ) +return ret; + + pdom_dev_data->pasid = pasid; + pdom_dev_data->dev_data = dev_data; + +/* Setup GCR3 table */ + ret =amd_iommu_set_gcr3 (dev_data, pasid, +iommu_virt_to_phys (domain->mm->pgd)); +if (ret) { +kfree (pdom_dev_data); +return ret;
Quoted 8 lines
drivers/iommu/amd/pasid.c line 160
Quoted 5 lines
drivers/iommu/amd/pasid.c new file +5
-0+ } + +spin_lock_irqsave (&sva_pdom->lock, flags); +list_add (&pdom_dev_data->list, &sva_pdom->dev_data_list); +spin_unlock_irqrestore (&sva_pdom->lock, flags);This doesn't seem right? The tracking list should be loaded before any change is made visible to the HW, or at least under the same lock.
Ok. I can move that up and then have error handler path to remove it.
-Vasant
Re: [PATCH v5 12/14] iommu/amd: Initial SVA support for AMD IOMMU
Quoted 27 lines · Vasant Hegde
Jason,
Quoted 14 lines · Jason Gunthorpe
Quoted 12 lines · Vasant Hegde
drivers/iommu/amd/pasid.c new file +12
-0+static int iommu_pasid_enable (struct iommu_dev_data *dev_data) +{ +struct device *dev = dev_data->dev; +int ret =0 ; + +spin_lock (&dev_data->lock); + +if (is_pasid_enabled (dev_data)) + goto out; + +if (!amd_iommu_pasid_supported ()) { + ret = -ENODEV ;Quoted 8 lines
drivers/iommu/amd/pasid.c line 45
Quoted 5 lines
drivers/iommu/amd/pasid.c new file +5
-0+ goto out; + } + +/* attach_device path enables device PASID feature */ +if (!dev_data->pasid_enabled) {How many times are we testing for this? Just check if the gcr3 table is installed once
Quoted 2 lines
One time for IOMMU capability (
amd_iommu_pasid_supported()) and one time for device capability.
Again I think this whole thing is out of sequence. The main focus should be on the gcr3 table. You should dirctly know if it has been installed or not via some direct means. Test all this stuff when you go to install it the first time.
Quoted 3 lines
is_pasid_enabled()is checked twice (once without lock, so that we can avoid lock in most cases and one inside lock to be sure no one else entered and enabled gcr3).
That never works, don't do that.
Quoted 15 lines
Quoted 15 lines
drivers/iommu/amd/pasid.c line 55
Quoted 12 lines
drivers/iommu/amd/pasid.c new file +10
-0+ ret = -EINVAL ; + goto out; + } + + ret =amd_iommu_gcr3_init (dev_data, dev->iommu->max_pasids); + +out: +spin_unlock (&dev_data->lock); +return ret; +}This seems like too much, and it doesn't need to be in a function..
Quoted 5 lines
Quoted 2 lines
1) Check directly if the gcr3 table is installed otherwise try to install it. That might be a usefull function
We need other checks to make sure both IOMMU and device is capable of PASID. Hence its a separate function.
That should be done at probe time and cached in the per-device max pasid valid. It is 0 if there is no pasid support.
Quoted 5 lines
Quoted 2 lines
2) Precompute the max pasids during device probe and store it in
iommu_dev_data. Just check if PASID >=max_pasidand failThis is not required .. as
set_dev_pasid()can directly checkdev->iommu->max_pasids.
That is not the same thing, dev->iommu->max_pasids is the PCI/DT capability only.
The driver still has to keep its own internal limit.
It is goofy and we should probably merge the driver limit and the core limit at some point - until then it is better to follow the pattern and keep a driver limit in the driver, doing all the work at probe time not during attach.
Quoted 10 lines
Quoted 9 lines
drivers/iommu/amd/pasid.c line 100
Quoted 4 lines
drivers/iommu/amd/pasid.c new file +4
-0+static void remove_dev_pasid (struct pdom_dev_data *pdom_dev_data) +{ +/* Update GCR3 table and flush IOTLB */ +amd_iommu_clear_gcr3 (pdom_dev_data->dev_data, pdom_dev_data->pasid);This is in the wrong place, there is only one DTE/GCR3
remove_devis touching. The list iteration below is just to clean up the tracking list it should not touch HW. Move this up intoamd_iommu_remove_dev_pasid.
Quoted 3 lines
This is used in
remove_dev_pasidandsva_mn_releasepath.This just clears GCR3[pasid] entry. Its not updating DTE.
Same argument, it should not be iterating, there is only ever one.
The release path is not removing the PASID, it is just disabling the GCR3 entry. The domain is still logically connected to that PASID as far as everything else is concerned.
Quoted 6 lines
Quoted 4 lines
And these functions related to the tracking list should be more general and called in more places. Just the tracking list itself should have a few patches to create it and situate it generically in the driver. Even the RID should be using the same mechanism.
That's after reworking protection domain structure. Not in this series.
:( I wish you'd get this stuff cleaned up properly first instead of building more mess on top of the wrong design.
Quoted 15 lines
Quoted 6 lines
Quoted 6 lines
drivers/iommu/amd/pasid.c new file +6
-0+/* Setup GCR3 table */ + ret =amd_iommu_set_gcr3 (dev_data, pasid, +iommu_virt_to_phys (domain->mm->pgd)); +if (ret) { +kfree (pdom_dev_data); +return ret;Quoted 8 lines
drivers/iommu/amd/pasid.c line 160
Quoted 5 lines
drivers/iommu/amd/pasid.c new file +5
-0+ } + +spin_lock_irqsave (&sva_pdom->lock, flags); +list_add (&pdom_dev_data->list, &sva_pdom->dev_data_list); +spin_unlock_irqrestore (&sva_pdom->lock, flags);This doesn't seem right? The tracking list should be loaded before any change is made visible to the HW, or at least under the same lock.
Quoted 1 line
Ok. I can move that up and then have error handler path to remove it.
Because, like this shows, it is hard to get it all right and it is even harder when everything is not consistent and there are two versions of the same flows.
Jason
Vasant Hegde
maintainerRe: [PATCH v5 12/14] iommu/amd: Initial SVA support for AMD IOMMU
Jason,
Quoted 28 lines · Jason Gunthorpe
Quoted 27 lines · Vasant Hegde
Jason,
Quoted 22 lines · Jason Gunthorpe
Quoted 7 lines · Vasant Hegde
drivers/iommu/amd/pasid.c new file +7
-0+static int iommu_pasid_enable (struct iommu_dev_data *dev_data) +{ +struct device *dev = dev_data->dev; +int ret =0 ; + +spin_lock (&dev_data->lock); +drivers/iommu/amd/pasid.c line 45
Quoted 10 lines
drivers/iommu/amd/pasid.c new file +10
-0+if (is_pasid_enabled (dev_data)) + goto out; + +if (!amd_iommu_pasid_supported ()) { + ret = -ENODEV ; + goto out; + } + +/* attach_device path enables device PASID feature */ +if (!dev_data->pasid_enabled) {How many times are we testing for this? Just check if the gcr3 table is installed once
Quoted 7 lines
Quoted 2 lines
One time for IOMMU capability (
amd_iommu_pasid_supported()) and one time for device capability.Again I think this whole thing is out of sequence. The main focus should be on the gcr3 table. You should dirctly know if it has been installed or not via some direct means. Test all this stuff when you go to install it the first time.
We are doing 1 SVA domain : 1 PASID : N devices model. That means we need to check all these things while attaching *first* PASID to device. (That's what we had discussed sometime back when I had all these things in feature_enable(SVA) path).
Ex: If device is in domain with V1 page table tries to attach PASID it should fail
If device is in domain of PT mode, then we should setup gcr3.
So I don't see how we can infer these things unless we have something like enable_feature(PASID).. which would have taken care of setting up things.
Quoted 7 lines
Quoted 4 lines
is_pasid_enabled()is checked twice (once without lock, so that we can avoid lock in most cases and one inside lock to be sure no one else entered and enabled gcr3).That never works, don't do that.
It does work as second one is lock protected. And the intention was to avoid locking for attaching second PASID onwards. Only for first time attaching PASID to device we will have check for two times.
Quoted 15 lines
Quoted 15 lines
Quoted 15 lines
drivers/iommu/amd/pasid.c line 55
Quoted 12 lines
drivers/iommu/amd/pasid.c new file +10
-0+ ret = -EINVAL ; + goto out; + } + + ret =amd_iommu_gcr3_init (dev_data, dev->iommu->max_pasids); + +out: +spin_unlock (&dev_data->lock); +return ret; +}This seems like too much, and it doesn't need to be in a function..
Quoted 8 lines
Quoted 5 lines
Quoted 2 lines
1) Check directly if the gcr3 table is installed otherwise try to install it. That might be a usefull function
We need other checks to make sure both IOMMU and device is capable of PASID. Hence its a separate function.
That should be done at probe time and cached in the per-device max pasid valid. It is 0 if there is no pasid support.
Ok. Yet another variable!
Quoted 9 lines
Quoted 6 lines
Quoted 3 lines
2) Precompute the max pasids during device probe and store it in
iommu_dev_data. Just check if PASID >=max_pasidand failThis is not required .. as
set_dev_pasid()can directly checkdev->iommu->max_pasids.That is not the same thing,
dev->iommu->max_pasidsis the PCI/DT capability only.
Its min of PCI device and corresponding IOMMU (see dev_iommu_get_max_pasids()).
Quoted 18 lines
The driver still has to keep its own internal limit.
It is goofy and we should probably merge the driver limit and the core limit at some point - until then it is better to follow the pattern and keep a driver limit in the driver, doing all the work at probe time not during attach.
Quoted 10 lines
Quoted 9 lines
drivers/iommu/amd/pasid.c line 100
Quoted 4 lines
drivers/iommu/amd/pasid.c new file +4
-0+static void remove_dev_pasid (struct pdom_dev_data *pdom_dev_data) +{ +/* Update GCR3 table and flush IOTLB */ +amd_iommu_clear_gcr3 (pdom_dev_data->dev_data, pdom_dev_data->pasid);This is in the wrong place, there is only one DTE/GCR3
remove_devis touching. The list iteration below is just to clean up the tracking list it should not touch HW. Move this up intoamd_iommu_remove_dev_pasid.
Quoted 5 lines
Quoted 3 lines
This is used in
remove_dev_pasidandsva_mn_releasepath.This just clears GCR3[pasid] entry. Its not updating DTE.
Same argument, it should not be iterating, there is only ever one.
We can have N device in same SVA domain. So we need to iterate to find the right entry in the list. So the flow is :
remove_dev_pasid()
// iterate over dev_data_list to find dev/pasid combination // Update gcr3[pasid] // remove entry from the list
I can take out 'update gcr3[pasid]' from remove_dev_pasid() and put it in sva_mn_release() and amd_iommu_remove_dev_pasid().. Just that its duplicate code!
Quoted 4 lines
The release path is not removing the PASID, it is just disabling the GCR3 entry. The domain is still logically connected to that PASID as far as everything else is concerned.
Right.. But for device side we need to clear the entry.
Quoted 26 lines
Quoted 7 lines
Quoted 5 lines
And these functions related to the tracking list should be more general and called in more places. Just the tracking list itself should have a few patches to create it and situate it generically in the driver. Even the RID should be using the same mechanism.
That's after reworking protection domain structure. Not in this series.
:( I wish you'd get this stuff cleaned up properly first instead of building more mess on top of the wrong design.
Quoted 15 lines
Quoted 14 lines
drivers/iommu/amd/pasid.c line 160
Quoted 11 lines
drivers/iommu/amd/pasid.c new file +11
-0+/* Setup GCR3 table */ + ret =amd_iommu_set_gcr3 (dev_data, pasid, +iommu_virt_to_phys (domain->mm->pgd)); +if (ret) { +kfree (pdom_dev_data); +return ret; + } + +spin_lock_irqsave (&sva_pdom->lock, flags); +list_add (&pdom_dev_data->list, &sva_pdom->dev_data_list); +spin_unlock_irqrestore (&sva_pdom->lock, flags);This doesn't seem right? The tracking list should be loaded before any change is made visible to the HW, or at least under the same lock.
Quoted 5 lines
Quoted 1 line
Ok. I can move that up and then have error handler path to remove it.
Because, like this shows, it is hard to get it all right and it is even harder when everything is not consistent and there are two versions of the same flows.
Ok.
-Vasant
Re: [PATCH v5 12/14] iommu/amd: Initial SVA support for AMD IOMMU
Quoted 40 lines · Vasant Hegde
Jason,
Quoted 28 lines · Jason Gunthorpe
Quoted 27 lines · Vasant Hegde
Jason,
Quoted 22 lines · Jason Gunthorpe
Quoted 7 lines · Vasant Hegde
drivers/iommu/amd/pasid.c new file +7
-0+static int iommu_pasid_enable (struct iommu_dev_data *dev_data) +{ +struct device *dev = dev_data->dev; +int ret =0 ; + +spin_lock (&dev_data->lock); +drivers/iommu/amd/pasid.c line 45
Quoted 10 lines
drivers/iommu/amd/pasid.c new file +10
-0+if (is_pasid_enabled (dev_data)) + goto out; + +if (!amd_iommu_pasid_supported ()) { + ret = -ENODEV ; + goto out; + } + +/* attach_device path enables device PASID feature */ +if (!dev_data->pasid_enabled) {How many times are we testing for this? Just check if the gcr3 table is installed once
Quoted 7 lines
Quoted 2 lines
One time for IOMMU capability (
amd_iommu_pasid_supported()) and one time for device capability.Again I think this whole thing is out of sequence. The main focus should be on the gcr3 table. You should dirctly know if it has been installed or not via some direct means. Test all this stuff when you go to install it the first time.
Quoted 4 lines
We are doing 1 SVA domain : 1 PASID : N devices model. That means we need to check all these things while attaching *first* PASID to device. (That's what we had discussed sometime back when I had all these things in
feature_enable(SVA)path).
I thought I said you 1 PASID is not technically correct, but you could get away it it for a short term. You should be planning to support N PASIDs because that is what the API defines.
Quoted 2 lines
Ex: If device is in domain with V1 page table tries to attach PASID it should fail
If device is in domain of PT mode, then we should setup gcr3.
Yes
Quoted 2 lines
So I don't see how we can infer these things unless we have something like
enable_feature(PASID).. which would have taken care of setting up things.
You just trivially check these conditions at the top of set_dev_pasid, look at what I did for ARM:
if (smmu_domain->smmu != master->smmu || pasid == IOMMU_NO_PASID) return -EINVAL; if (!master->cd_table.in_ste && sid_domain->type != IOMMU_DOMAIN_IDENTITY && sid_domain->type != IOMMU_DOMAIN_BLOCKED) return -EINVAL;
For AMD "cd_table in_ste" means that the DTE points to a GCR3 table already. This is trivially tracked in the DTE programming in set_dte because you know if the dte is being configured with a GCR3 or not.
The other cases represent the situations where we know how to upgrade a DTE for those domains to one with a GCR3. Everything else is blocked.
Quoted 9 lines
Quoted 5 lines
Quoted 3 lines
is_pasid_enabled()is checked twice (once without lock, so that we can avoid lock in most cases and one inside lock to be sure no one else entered and enabled gcr3).That never works, don't do that.
It does work as second one is lock protected. And the intention was to avoid locking for attaching second PASID onwards. Only for first time attaching PASID to device we will have check for two times.
You can get racy false negatives, that are hard to reason about.
CPU0 CPU 1
lock() change state to !a
if (!a)
forget it
a = false unlock()lock()
if (!a)
forget it
change state to a
a = trueunlock()
There are ways with atomics you can build those kinds of lockless patterns, but they are tricky and not justified here.
Jason
Vasant Hegde
maintainerRe: [PATCH v5 12/14] iommu/amd: Initial SVA support for AMD IOMMU
Quoted 41 lines · Jason Gunthorpe
Quoted 40 lines · Vasant Hegde
Jason,
Quoted 35 lines · Jason Gunthorpe
Quoted 27 lines · Vasant Hegde
Jason,
Quoted 14 lines · Jason Gunthorpe
Quoted 12 lines · Vasant Hegde
drivers/iommu/amd/pasid.c new file +12
-0+static int iommu_pasid_enable (struct iommu_dev_data *dev_data) +{ +struct device *dev = dev_data->dev; +int ret =0 ; + +spin_lock (&dev_data->lock); + +if (is_pasid_enabled (dev_data)) + goto out; + +if (!amd_iommu_pasid_supported ()) { + ret = -ENODEV ;Quoted 8 lines
drivers/iommu/amd/pasid.c line 45
Quoted 5 lines
drivers/iommu/amd/pasid.c new file +5
-0+ goto out; + } + +/* attach_device path enables device PASID feature */ +if (!dev_data->pasid_enabled) {How many times are we testing for this? Just check if the gcr3 table is installed once
Quoted 2 lines
One time for IOMMU capability (
amd_iommu_pasid_supported()) and one time for device capability.Again I think this whole thing is out of sequence. The main focus should be on the gcr3 table. You should dirctly know if it has been installed or not via some direct means. Test all this stuff when you go to install it the first time.
Quoted 8 lines
Quoted 4 lines
We are doing 1 SVA domain : 1 PASID : N devices model. That means we need to check all these things while attaching *first* PASID to device. (That's what we had discussed sometime back when I had all these things in
feature_enable(SVA)path).I thought I said you 1 PASID is not technically correct, but you could get away it it for a short term. You should be planning to support N PASIDs because that is what the API defines.
I am describing API in SVA context only. In that flow once we allocate a SVA domain for a PASID, then all devices for that PASID is attached to same domain.
Quoted 20 lines
Quoted 3 lines
Ex: If device is in domain with V1 page table tries to attach PASID it should fail
If device is in domain of PT mode, then we should setup gcr3.Yes
Quoted 2 lines
So I don't see how we can infer these things unless we have something like
enable_feature(PASID).. which would have taken care of setting up things.You just trivially check these conditions at the top of
set_dev_pasid, look at what I did for ARM:if (smmu_domain->smmu != master->smmu || pasid == IOMMU_NO_PASID) return -EINVAL; if (!master->cd_table.in_ste && sid_domain->type != IOMMU_DOMAIN_IDENTITY && sid_domain->type != IOMMU_DOMAIN_BLOCKED) return -EINVAL;
Quoted 6 lines
For AMD "
cd_tablein_ste" means that the DTE points to a GCR3 table already. This is trivially tracked in the DTE programming inset_dtebecause you know if the dte is being configured with a GCR3 or not.The other cases represent the situations where we know how to upgrade a DTE for those domains to one with a GCR3. Everything else is blocked.
I got something similar. I have reworked set/remove pasid path completely. I will try to post it soon.
Quoted 13 lines
Quoted 10 lines
Quoted 6 lines
Quoted 4 lines
is_pasid_enabled()is checked twice (once without lock, so that we can avoid lock in most cases and one inside lock to be sure no one else entered and enabled gcr3).That never works, don't do that.
It does work as second one is lock protected. And the intention was to avoid locking for attaching second PASID onwards. Only for first time attaching PASID to device we will have check for two times.
You can get racy false negatives, that are hard to reason about.
Quoted 13 lines
CPU0 CPU 1
lock()change state to !a
if (!a)
forget it
a = falseunlock()lock()
if (!a)
forget it
change state to a
a = trueunlock()
I don't hit above like scenario as its enable once/check awlays until all PASID binding is removed. Anyway I have reworked this part completely and removed most of these checks.
-Vasant
Re: [PATCH v5 12/14] iommu/amd: Initial SVA support for AMD IOMMU
Quoted 5 lines · Vasant Hegde
Quoted 5 lines
Quoted 4 lines
We are doing 1 SVA domain : 1 PASID : N devices model. That means we need to check all these things while attaching *first* PASID to device. (That's what we had discussed sometime back when I had all these things in
feature_enable(SVA)path).
Quoted 7 lines
Quoted 3 lines
I thought I said you 1 PASID is not technically correct, but you could get away it it for a short term. You should be planning to support N PASIDs because that is what the API defines.
I am describing API in SVA context only. In that flow once we allocate a SVA domain for a PASID, then all devices for that PASID is attached to same domain.
It is OK to take a shortcut here if it helps, but that is not the API model. Domains, SVA or not, do not have PASIDs. The only place a PASID comes is via the set_dev_pasid() argument and any domain should be attachable to any combination of PASIDs.
So the only place a PASID should be stored is in the elements of the invalidation tracking list of the domain. When you get that all completed it should all be uniform and a limitation like this should go away. But this is fine to hold over for a followup that completes the PASID support.
Quoted 15 lines
Quoted 15 lines
You just trivially check these conditions at the top of
set_dev_pasid, look at what I did for ARM:if (smmu_domain->smmu != master->smmu || pasid == IOMMU_NO_PASID) return -EINVAL; if (!master->cd_table.in_ste && sid_domain->type != IOMMU_DOMAIN_IDENTITY && sid_domain->type != IOMMU_DOMAIN_BLOCKED) return -EINVAL;For AMD "
cd_tablein_ste" means that the DTE points to a GCR3 table already. This is trivially tracked in the DTE programming inset_dtebecause you know if the dte is being configured with a GCR3 or not.
Quoted 5 lines
Quoted 2 lines
The other cases represent the situations where we know how to upgrade a DTE for those domains to one with a GCR3. Everything else is blocked.
I got something similar. I have reworked set/remove pasid path completely. I will try to post it soon.
Nice!
Jason
Vasant Hegde
maintainerPATCH v5 13/14 iommu: Add ops->domain_alloc_sva()
In reply to Vasant HegdeFrom: Jason Gunthorpe <[email protected]>
Make a new op that receives the device and the mm_struct that the SVA domain should be created for. Unlike domain_alloc_paging() the dev argument is never NULL here.
This allows drivers to fully initialize the SVA domain and allocate the mmu_notifier during allocation. It allows the notifier lifetime to follow the lifetime of the iommu_domain.
Since we have only one call site, upgrade the new op to return ERR_PTR instead of NULL.
--- drivers/iommu/iommu-sva.c | 16 +++++++++++----- include/linux/iommu.h | 3 +++ 2 files changed, 14 insertions(+), 5 deletions(-)
drivers/iommu/iommu-sva.c +11 -5
@@ -99,8 +99,8 @@ struct iommu_sva *iommu_sva_bind_device(struct device *dev, struct mm_struct *mm/* Allocate a new domain and set it on device pasid. */ domain =iommu_sva_domain_alloc (dev, mm); -if (!domain) { - ret = -ENOMEM ; +if (IS_ERR (domain)) { + ret =PTR_ERR (domain); goto out_free_handle; }
@@ -266,9 +266,15 @@ struct iommu_domain *iommu_sva_domain_alloc(struct device *dev,const struct iommu_ops *ops =dev_iommu_ops (dev);struct iommu_domain *domain; - domain = ops->domain_alloc (IOMMU_DOMAIN_SVA ); -if (!domain) -return NULL ; +if (ops->domain_alloc_sva) { + domain = ops->domain_alloc_sva (dev, mm); +if (IS_ERR (domain)) +return domain; + }else { + domain = ops->domain_alloc (IOMMU_DOMAIN_SVA ); +if (!domain) +return ERR_PTR (-ENOMEM ); + } domain->type =IOMMU_DOMAIN_SVA ;mmgrab (mm);
include/linux/iommu.h +3 -0
@@ -454,6 +454,7 @@ static inline int __iommu_copy_struct_from_user(* Upon failure, ERR_PTR must be returned. * @domain_alloc_paging: Allocate an iommu_domain that can be used for * UNMANAGED, DMA, and DMA_FQ domain types. +* @domain_alloc_sva: Allocate an iommu_domain for Shared Virtual Addressing. * @probe_device: Add device to iommu driver handling * @release_device: Remove device from iommu driver handling * @probe_finalize: Do final setup work after the device is added to an IOMMU
@@ -494,6 +495,8 @@ struct iommu_ops { struct device *dev, u32 flags, struct iommu_domain *parent, const struct iommu_user_data *user_data);struct iommu_domain *(*domain_alloc_paging)(struct device *dev); +struct iommu_domain *(*domain_alloc_sva)(struct device *dev, +struct mm_struct *mm);struct iommu_device *(*probe_device)(struct device *dev);void (*release_device)(struct device *dev);
Signature · 1 line
2.31.1
Vasant Hegde
maintainerPATCH v5 14/14 iommu/amd: Add SVA domain support
In reply to Vasant Hegde- Allocate SVA domain and setup mmu notifier. In free path unregister mmu notifier and free protection domain.
- Add mmu notifier callback function. It will retrieve SVA protection domain and invalidates IO/TLB.
--- drivers/iommu/amd/amd_iommu.h | 5 ++ drivers/iommu/amd/amd_iommu_types.h | 1 + drivers/iommu/amd/iommu.c | 10 ++-- drivers/iommu/amd/pasid.c | 80 +++++++++++++++++++++++++++++ 4 files changed, 93 insertions(+), 3 deletions(-)
drivers/iommu/amd/amd_iommu.h +5 -0
@@ -45,6 +45,11 @@ extern enum io_pgtable_fmt amd_iommu_pgtable;extern int amd_iommu_gpt_level;/* Protection domain ops */ +struct protection_domain *protection_domain_alloc (unsigned int type); +void protection_domain_free (struct protection_domain *domain); +struct iommu_domain *amd_iommu_domain_alloc_sva (struct device *dev, +struct mm_struct *mm); +void amd_iommu_domain_free (struct iommu_domain *dom);int iommu_sva_set_dev_pasid (struct iommu_domain *domain,struct device *dev,ioasid_t pasid);void amd_iommu_remove_dev_pasid (struct device *dev,ioasid_t pasid);
drivers/iommu/amd/amd_iommu_types.h +1 -0
@@ -594,6 +594,7 @@ struct protection_domain {unsigned dev_cnt;/* devices assigned to this domain */ unsigned dev_iommu[MAX_IOMMUS ];/* per-IOMMU reference count */ +struct mmu_notifier mn;/* mmu notifier for the SVA domain */ struct list_head dev_data_list;/* List of pdom_dev_data */ };
drivers/iommu/amd/iommu.c +7 -3
@@ -2251,7 +2251,7 @@ static void cleanup_domain(struct protection_domain *domain)WARN_ON (domain->dev_cnt !=0 ); } -static void protection_domain_free (struct protection_domain *domain) +void protection_domain_free (struct protection_domain *domain) {if (!domain)return ;
@@ -2294,7 +2294,7 @@ static int protection_domain_init_v2(struct protection_domain *pdom)return 0 ; } -static struct protection_domain *protection_domain_alloc (unsigned int type) +struct protection_domain *protection_domain_alloc (unsigned int type) {struct io_pgtable_ops *pgtbl_ops;struct protection_domain *domain;
@@ -2317,6 +2317,7 @@ static struct protection_domain *protection_domain_alloc(unsigned int type)switch (type) {/* No need to allocate io pgtable ops in passthrough mode */ case IOMMU_DOMAIN_IDENTITY : +case IOMMU_DOMAIN_SVA :return domain;case IOMMU_DOMAIN_DMA : pgtable = amd_iommu_pgtable;
@@ -2436,7 +2437,7 @@ amd_iommu_domain_alloc_user(struct device *dev, u32 flags,return do_iommu_domain_alloc (type, dev, flags); } -static void amd_iommu_domain_free (struct iommu_domain *dom) +void amd_iommu_domain_free (struct iommu_domain *dom) {struct protection_domain *domain;unsigned long flags;
@@ -2804,6 +2805,7 @@ static int amd_iommu_dev_enable_feature(struct device *dev,switch (feat) {case IOMMU_DEV_FEAT_IOPF : +case IOMMU_DEV_FEAT_SVA :break ;default : ret = -EINVAL ;
@@ -2819,6 +2821,7 @@ static int amd_iommu_dev_disable_feature(struct device *dev,switch (feat) {case IOMMU_DEV_FEAT_IOPF : +case IOMMU_DEV_FEAT_SVA :break ;default : ret = -EINVAL ;
@@ -2831,6 +2834,7 @@ const struct iommu_ops amd_iommu_ops = { .capable = amd_iommu_capable, .domain_alloc = amd_iommu_domain_alloc, .domain_alloc_user = amd_iommu_domain_alloc_user, + .domain_alloc_sva = amd_iommu_domain_alloc_sva, .probe_device = amd_iommu_probe_device, .release_device = amd_iommu_release_device, .probe_finalize = amd_iommu_probe_finalize,
drivers/iommu/amd/pasid.c +80 -0
89 lines not on this page · raw message
Signature · 1 line
2.31.1
Re: [PATCH v5 14/14] iommu/amd: Add SVA domain support
Quoted 6 lines · Vasant Hegde
- Allocate SVA domain and setup mmu notifier. In free path unregister mmu notifier and free protection domain.
- Add mmu notifier callback function. It will retrieve SVA protection domain and invalidates IO/TLB.
Quoted 7 lines
Signed-off-by Vasant Hegde <[email protected]>--- drivers/iommu/amd/amd_iommu.h | 5 ++ drivers/iommu/amd/amd_iommu_types.h | 1 + drivers/iommu/amd/iommu.c | 10 ++-- drivers/iommu/amd/pasid.c | 80 +++++++++++++++++++++++++++++ 4 files changed, 93 insertions(+), 3 deletions(-)
Jason
Vasant Hegde
maintainerQuoted 20 lines · Vasant Hegde
This is part 4 of the 4-part series to introduce Share Virtual Address (SVA) support for devices, which can support PCI ATS, PASID and PRI capabilities. These devices are referred to as SVA-capable devices in this series.
It contains the following enhancements:
* Patch 1 - 3:
Rename, add support to enable/disable features, update DTE etc.* Patch 4 - 10:
Add IOPF support* Patch 11 - 14:
Introduce SVA supportThis patch series is based on top of SVA Part 3 v5.
https://lore.kernel.org/linux-iommu/[email protected]/T/#t
Quoted 6 lines
Also depends on :
1) Baolu's IOPF improvementhttps://lore.kernel.org/linux-iommu/[email protected]/This is also available at github :
https://github.com/AMDESE/linux/tree/iommu_sva_part4_v4_v6.7_rc8
Sorry for the typo. Correct link :
https://github.com/AMDESE/linux/tree/iommu_sva_part4_v5_v6.7_rc8
-Vasant