rockchip: Add support for rv1126 based Sonoff iHost Gateway
Subsystems (3)
v2 cover rockchip: Add support for rv1126 based Sonoff iHost Gateway
Sonoff iHost is gateway device designed to provide a Smart Home Hub, it is based on Rockchip RV1126. It features Wifi, BT and Zigbee radios as required by many smart home devices.
Features:
- Rockchip RV1126
- 4GB DDR4
- 8GB eMMC
- microSD slot
- RMII Ethernet PHY
- 1x USB 2.0 Host
- 1x USB 2.0 OTG
- Realtek RTL8723DS WiFi/BT
- EFR32MG21 Silabs Zigbee radio
- Speaker/Microphone
Sync rv1126 dts from linux v6.8-rc1, add support for ddr4 ram and add board support for the Sonoff ihost.
Changes in v2:
- New patch to clean up distro boot from rv1126_common.h
- Remove board config not required with standard boot
Tim Lunn (6):
arm: dts: rockchip: Sync rv1126 dts from linux 6.8-rc1
ram: rockchip: Add rv1126 ddr4 support
rockchip: Convert rv1126 to standard boot
board: rockchip: Add Sonoff iHost board
rockchip: rv1126: select SPL_OPTEE_IMAGE
rockchip: rv1126: Move RAM disk address
arch/arm/dts/rv1126-edgeble-neu2-io.dts | 70 +++ arch/arm/dts/rv1126-edgeble-neu2.dtsi | 27 +- arch/arm/dts/rv1126-pinctrl.dtsi | 130 ++++++ arch/arm/dts/rv1126-sonoff-ihost-u-boot.dtsi | 13 + arch/arm/dts/rv1126-sonoff-ihost.dts | 29 ++ arch/arm/dts/rv1126-sonoff-ihost.dtsi | 404 ++++++++++++++++++ arch/arm/dts/rv1126.dtsi | 185 ++++++++ arch/arm/mach-rockchip/Kconfig | 1 + arch/arm/mach-rockchip/rv1126/Kconfig | 8 + board/itead/sonoff-ihost/Kconfig | 16 + board/itead/sonoff-ihost/MAINTAINERS | 6 + configs/sonoff-ihost-rv1126_defconfig | 60 +++ doc/board/rockchip/rockchip.rst | 1 + .../sdram-rv1126-ddr4-detect-1056.inc | 75 ++++ .../rockchip/sdram-rv1126-ddr4-detect-328.inc | 75 ++++ .../rockchip/sdram-rv1126-ddr4-detect-396.inc | 75 ++++ .../rockchip/sdram-rv1126-ddr4-detect-528.inc | 75 ++++ .../rockchip/sdram-rv1126-ddr4-detect-664.inc | 75 ++++ .../rockchip/sdram-rv1126-ddr4-detect-784.inc | 75 ++++ .../rockchip/sdram-rv1126-ddr4-detect-924.inc | 75 ++++ drivers/ram/rockchip/sdram_rv1126.c | 8 + include/configs/neural-compute-module-2.h | 6 - include/configs/rv1126_common.h | 5 +- include/configs/sonoff-ihost.h | 10 + 24 files changed, 1485 insertions(+), 19 deletions(-) create mode 100644 arch/arm/dts/rv1126-sonoff-ihost-u-boot.dtsi create mode 100644 arch/arm/dts/rv1126-sonoff-ihost.dts create mode 100644 arch/arm/dts/rv1126-sonoff-ihost.dtsi create mode 100644 board/itead/sonoff-ihost/Kconfig create mode 100644 board/itead/sonoff-ihost/MAINTAINERS create mode 100644 configs/sonoff-ihost-rv1126_defconfig create mode 100644 drivers/ram/rockchip/sdram-rv1126-ddr4-detect-1056.inc create mode 100644 drivers/ram/rockchip/sdram-rv1126-ddr4-detect-328.inc create mode 100644 drivers/ram/rockchip/sdram-rv1126-ddr4-detect-396.inc create mode 100644 drivers/ram/rockchip/sdram-rv1126-ddr4-detect-528.inc create mode 100644 drivers/ram/rockchip/sdram-rv1126-ddr4-detect-664.inc create mode 100644 drivers/ram/rockchip/sdram-rv1126-ddr4-detect-784.inc create mode 100644 drivers/ram/rockchip/sdram-rv1126-ddr4-detect-924.inc create mode 100644 include/configs/sonoff-ihost.h
Signature · 1 line
2.40.1
PATCH v2 1/6 arm: dts: rockchip: Sync rv1126 dts from linux 6.8-rc1
Sync linux dts files for rv1126 boards from linux v6.8-rc1 tag. Includes the newly added dts for Sonoff iHost.
---
(no changes since v1)
arch/arm/dts/rv1126-edgeble-neu2-io.dts | 70 ++++ arch/arm/dts/rv1126-edgeble-neu2.dtsi | 27 +- arch/arm/dts/rv1126-pinctrl.dtsi | 130 ++++++++ arch/arm/dts/rv1126-sonoff-ihost.dts | 29 ++ arch/arm/dts/rv1126-sonoff-ihost.dtsi | 404 ++++++++++++++++++++++++ arch/arm/dts/rv1126.dtsi | 185 +++++++++++ 6 files changed, 835 insertions(+), 10 deletions(-) create mode 100644 arch/arm/dts/rv1126-sonoff-ihost.dts create mode 100644 arch/arm/dts/rv1126-sonoff-ihost.dtsi
arch/arm/dts/rv1126-edgeble-neu2-io.dts +70 -0
@@ -20,6 +20,76 @@ chosen { stdout-path = "serial2:1500000n8"; }; + + vcc12v_dcin: vcc12v-dcin-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc12v_dcin"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + }; + + vcc5v0_sys: vcc5v0-sys-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc5v0_sys"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <&vcc12v_dcin>; + }; + + v3v3_sys: v3v3-sys-regulator { + compatible = "regulator-fixed"; + regulator-name = "v3v3_sys"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vcc5v0_sys>; + }; +}; + +&gmac { + assigned-clocks = <&cru CLK_GMAC_SRC>, <&cru CLK_GMAC_TX_RX>, + <&cru CLK_GMAC_ETHERNET_OUT>; + assigned-clock-parents = <&cru CLK_GMAC_SRC_M1>, <&cru RGMII_MODE_CLK>; + assigned-clock-rates = <125000000>, <0>, <25000000>; + clock_in_out = "input"; + phy-handle = <&phy>; + phy-mode = "rgmii"; + phy-supply = <&vcc_3v3>; + pinctrl-names = "default"; + pinctrl-0 = <&rgmiim1_miim &rgmiim1_bus2 &rgmiim1_bus4 &clk_out_ethernetm1_pins>; + tx_delay = <0x2a>; + rx_delay = <0x1a>; + status = "okay"; +}; + +&mdio { + phy: ethernet-phy@0 { + compatible = "ethernet-phy-id001c.c916", + "ethernet-phy-ieee802.3-c22"; + reg = <0x0>; + pinctrl-names = "default"; + pinctrl-0 = <ð_phy_rst>; + reset-assert-us = <20000>; + reset-deassert-us = <100000>; + reset-gpios = <&gpio0 RK_PB6 GPIO_ACTIVE_LOW>; + }; +}; + +&pinctrl { + ethernet { + eth_phy_rst: eth-phy-rst { + rockchip,pins = <0 RK_PB6 RK_FUNC_GPIO &pcfg_pull_down>; + }; + }; +}; + +&pwm11 { + status = "okay"; }; &sdmmc {
arch/arm/dts/rv1126-edgeble-neu2.dtsi +17 -10
@@ -11,15 +11,6 @@ mmc0 = &emmc; }; - vcc5v0_sys: vcc5v0-sys-regulator { - compatible = "regulator-fixed"; - regulator-name = "vcc5v0_sys"; - regulator-always-on; - regulator-boot-on; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - }; - vccio_flash: vccio-flash-regulator { compatible = "regulator-fixed"; enable-active-high;
@@ -52,7 +43,7 @@ bus-width = <8>; non-removable; pinctrl-names = "default"; - pinctrl-0 = <&emmc_bus8 &emmc_cmd &emmc_clk &emmc_rstnout>; + pinctrl-0 = <&emmc_bus8 &emmc_cmd &emmc_clk>; rockchip,default-sample-phase = <90>; vmmc-supply = <&vcc_3v3>; vqmmc-supply = <&vccio_flash>;
@@ -301,6 +292,22 @@ status = "okay"; }; +&sfc { + pinctrl-names = "default"; + pinctrl-0 = <&fspi_pins>; + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <50000000>; + spi-rx-bus-width = <4>; + spi-tx-bus-width = <1>; + }; +}; + &sdio { bus-width = <4>; cap-sd-highspeed;
arch/arm/dts/rv1126-pinctrl.dtsi +130 -0
165 lines not on this page · raw message
arch/arm/dts/rv1126-sonoff-ihost.dts new file +29 -0
@@ -0,0 +1,29 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2020 Rockchip Electronics Co., Ltd. + */ + +/dts-v1/; +#include "rv1126.dtsi" +#include "rv1126-sonoff-ihost.dtsi" + +/ { + model = "Sonoff iHost 4G"; + compatible = "itead,sonoff-ihost", "rockchip,rv1126"; +}; + +&cpu0 { + cpu-supply = <&vdd_arm>; +}; + +&cpu1 { + cpu-supply = <&vdd_arm>; +}; + +&cpu2 { + cpu-supply = <&vdd_arm>; +}; + +&cpu3 { + cpu-supply = <&vdd_arm>; +};
arch/arm/dts/rv1126-sonoff-ihost.dtsi new file +404 -0
404 lines not on this page · raw message
arch/arm/dts/rv1126.dtsi +185 -0
239 lines not on this page · raw message
Signature · 1 line
2.40.1
Re: [PATCH v2 1/6] arm: dts: rockchip: Sync rv1126 dts from linux 6.8-rc1
Quoted 4 lines · Tim Lunn
Sync linux dts files for rv1126 boards from linux v6.8-rc1 tag. Includes the newly added dts for Sonoff iHost.
Signed-off-by Tim Lunn <[email protected]>
Thanks,
- Kever
Quoted 1,019 lines
---
(no changes since v1)
arch/arm/dts/rv1126-edgeble-neu2-io.dts | 70 ++++ arch/arm/dts/rv1126-edgeble-neu2.dtsi | 27 +- arch/arm/dts/rv1126-pinctrl.dtsi | 130 ++++++++ arch/arm/dts/rv1126-sonoff-ihost.dts | 29 ++ arch/arm/dts/rv1126-sonoff-ihost.dtsi | 404 ++++++++++++++++++++++++ arch/arm/dts/rv1126.dtsi | 185 +++++++++++ 6 files changed, 835 insertions(+), 10 deletions(-)create mode 100644
arch/arm/dts/rv1126-sonoff-ihost.dtscreate mode 100644arch/arm/dts/rv1126-sonoff-ihost.dtsiarch/arm/dts/rv1126-edgeble-neu2-io.dts +70
-0@@ -20,6 +20,76 @@ chosen { stdout-path = "serial2:1500000n8"; }; + + vcc12v_dcin: vcc12v-dcin-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc12v_dcin"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + }; + + vcc5v0_sys: vcc5v0-sys-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc5v0_sys"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <&vcc12v_dcin>; + }; + + v3v3_sys: v3v3-sys-regulator { + compatible = "regulator-fixed"; + regulator-name = "v3v3_sys"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vcc5v0_sys>; + }; +}; + +&gmac { + assigned-clocks = <&cru CLK_GMAC_SRC>, <&cru CLK_GMAC_TX_RX>, + <&cru CLK_GMAC_ETHERNET_OUT>; + assigned-clock-parents = <&cru CLK_GMAC_SRC_M1>, <&cru RGMII_MODE_CLK>; + assigned-clock-rates = <125000000>, <0>, <25000000>; + clock_in_out = "input"; + phy-handle = <&phy>; + phy-mode = "rgmii"; + phy-supply = <&vcc_3v3>; + pinctrl-names = "default"; + pinctrl-0 = <&rgmiim1_miim &rgmiim1_bus2 &rgmiim1_bus4 &clk_out_ethernetm1_pins>; + tx_delay = <0x2a>; + rx_delay = <0x1a>; + status = "okay"; +}; + +&mdio { + phy: ethernet-phy@0 { + compatible = "ethernet-phy-id001c.c916", + "ethernet-phy-ieee802.3-c22"; + reg = <0x0>; + pinctrl-names = "default"; + pinctrl-0 = <ð_phy_rst>; + reset-assert-us = <20000>; + reset-deassert-us = <100000>; + reset-gpios = <&gpio0 RK_PB6 GPIO_ACTIVE_LOW>; + }; +}; + +&pinctrl { + ethernet { + eth_phy_rst: eth-phy-rst { + rockchip,pins = <0 RK_PB6 RK_FUNC_GPIO &pcfg_pull_down>; + }; + }; +}; + +&pwm11 { + status = "okay"; }; &sdmmc {arch/arm/dts/rv1126-edgeble-neu2.dtsi +17
-10@@ -11,15 +11,6 @@ mmc0 = &emmc; }; - vcc5v0_sys: vcc5v0-sys-regulator { - compatible = "regulator-fixed"; - regulator-name = "vcc5v0_sys"; - regulator-always-on; - regulator-boot-on; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - }; - vccio_flash: vccio-flash-regulator { compatible = "regulator-fixed"; enable-active-high;@@ -52,7 +43,7 @@ bus-width = <8>; non-removable; pinctrl-names = "default"; - pinctrl-0 = <&emmc_bus8 &emmc_cmd &emmc_clk &emmc_rstnout>; + pinctrl-0 = <&emmc_bus8 &emmc_cmd &emmc_clk>; rockchip,default-sample-phase = <90>; vmmc-supply = <&vcc_3v3>; vqmmc-supply = <&vccio_flash>;@@ -301,6 +292,22 @@ status = "okay"; }; +&sfc { + pinctrl-names = "default"; + pinctrl-0 = <&fspi_pins>; + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <50000000>; + spi-rx-bus-width = <4>; + spi-tx-bus-width = <1>; + }; +}; + &sdio { bus-width = <4>; cap-sd-highspeed;arch/arm/dts/rv1126-pinctrl.dtsi +130
-0@@ -11,6 +11,14 @@ * by adding changes at end of this file. */ &pinctrl { + clk_out_ethernet { + /omit-if-no-ref/ + clk_out_ethernetm1_pins: clk-out-ethernetm1-pins { + rockchip,pins = + /* clk_out_ethernet_m1 */ + <2 RK_PC5 2 &pcfg_pull_none>; + }; + }; emmc { /omit-if-no-ref/ emmc_rstnout: emmc-rstnout {@@ -51,6 +59,24 @@ <0 RK_PD5 2 &pcfg_pull_up_drv_level_2>; }; }; + fspi { + /omit-if-no-ref/ + fspi_pins: fspi-pins { + rockchip,pins = + /* fspi_clk */ + <1 RK_PA3 3 &pcfg_pull_down>, + /* fspi_cs0n */ + <0 RK_PD4 3 &pcfg_pull_up>, + /* fspi_d0 */ + <1 RK_PA0 3 &pcfg_pull_up>, + /* fspi_d1 */ + <1 RK_PA1 3 &pcfg_pull_up>, + /* fspi_d2 */ + <0 RK_PD6 3 &pcfg_pull_up>, + /* fspi_d3 */ + <1 RK_PA2 3 &pcfg_pull_up>; + }; + }; i2c0 { /omit-if-no-ref/ i2c0_xfer: i2c0-xfer {@@ -61,6 +87,86 @@ <0 RK_PB5 1 &pcfg_pull_none_drv_level_0_smt>; }; }; + i2c2 { + /omit-if-no-ref/ + i2c2_xfer: i2c2-xfer { + rockchip,pins = + /* i2c2_scl */ + <0 RK_PC2 1 &pcfg_pull_none_drv_level_0_smt>, + /* i2c2_sda */ + <0 RK_PC3 1 &pcfg_pull_none_drv_level_0_smt>; + }; + }; + pwm2 { + /omit-if-no-ref/ + pwm2m0_pins: pwm2m0-pins { + rockchip,pins = + /* pwm2_pin_m0 */ + <0 RK_PC0 3 &pcfg_pull_none>; + }; + }; + pwm11 { + /omit-if-no-ref/ + pwm11m0_pins: pwm11m0-pins { + rockchip,pins = + /* pwm11_pin_m0 */ + <3 RK_PA7 6 &pcfg_pull_none>; + }; + }; + rgmii { + /omit-if-no-ref/ + rgmiim1_miim: rgmiim1-miim { + rockchip,pins = + /* rgmii_mdc_m1 */ + <2 RK_PC2 2 &pcfg_pull_none>, + /* rgmii_mdio_m1 */ + <2 RK_PC1 2 &pcfg_pull_none>; + }; + /omit-if-no-ref/ + rgmiim1_rxer: rgmiim1-rxer { + rockchip,pins = + /* rgmii_rxer_m1 */ + <2 RK_PC0 2 &pcfg_pull_none>; + }; + /omit-if-no-ref/ + rgmiim1_bus2: rgmiim1-bus2 { + rockchip,pins = + /* rgmii_rxd0_m1 */ + <2 RK_PB5 2 &pcfg_pull_none>, + /* rgmii_rxd1_m1 */ + <2 RK_PB6 2 &pcfg_pull_none>, + /* rgmii_rxdv_m1 */ + <2 RK_PB4 2 &pcfg_pull_none>, + /* rgmii_txd0_m1 */ + <2 RK_PC3 2 &pcfg_pull_none_drv_level_3>, + /* rgmii_txd1_m1 */ + <2 RK_PC4 2 &pcfg_pull_none_drv_level_3>, + /* rgmii_txen_m1 */ + <2 RK_PC6 2 &pcfg_pull_none_drv_level_3>; + }; + /omit-if-no-ref/ + rgmiim1_bus4: rgmiim1-bus4 { + rockchip,pins = + /* rgmii_rxclk_m1 */ + <2 RK_PD3 2 &pcfg_pull_none>, + /* rgmii_rxd2_m1 */ + <2 RK_PC7 2 &pcfg_pull_none>, + /* rgmii_rxd3_m1 */ + <2 RK_PD0 2 &pcfg_pull_none>, + /* rgmii_txclk_m1 */ + <2 RK_PD2 2 &pcfg_pull_none_drv_level_3>, + /* rgmii_txd2_m1 */ + <2 RK_PD1 2 &pcfg_pull_none_drv_level_3>, + /* rgmii_txd3_m1 */ + <2 RK_PA4 2 &pcfg_pull_none_drv_level_3>; + }; + /omit-if-no-ref/ + rgmiim1_mclkinout: rgmiim1-mclkinout { + rockchip,pins = + /* rgmii_clk_m1 */ + <2 RK_PB7 2 &pcfg_pull_none>; + }; + }; sdmmc0 { /omit-if-no-ref/ sdmmc0_bus4: sdmmc0-bus4 {@@ -187,6 +293,14 @@ /* uart3_tx_m0 */ <3 RK_PC6 4 &pcfg_pull_up>; }; + /omit-if-no-ref/ + uart3m2_xfer: uart3m2-xfer { + rockchip,pins = + /* uart3_rx_m2 */ + <3 RK_PA1 4 &pcfg_pull_up>, + /* uart3_tx_m2 */ + <3 RK_PA0 4 &pcfg_pull_up>; + }; }; uart4 { /omit-if-no-ref/@@ -197,6 +311,14 @@ /* uart4_tx_m0 */ <3 RK_PA4 4 &pcfg_pull_up>; }; + /omit-if-no-ref/ + uart4m2_xfer: uart4m2-xfer { + rockchip,pins = + /* uart4_rx_m2 */ + <1 RK_PD4 3 &pcfg_pull_up>, + /* uart4_tx_m2 */ + <1 RK_PD5 3 &pcfg_pull_up>; + }; }; uart5 { /omit-if-no-ref/@@ -207,5 +329,13 @@ /* uart5_tx_m0 */ <3 RK_PA6 4 &pcfg_pull_up>; }; + /omit-if-no-ref/ + uart5m2_xfer: uart5m2-xfer { + rockchip,pins = + /* uart5_rx_m2 */ + <2 RK_PA1 3 &pcfg_pull_up>, + /* uart5_tx_m2 */ + <2 RK_PA0 3 &pcfg_pull_up>; + }; }; };arch/arm/dts/rv1126-sonoff-ihost.dts new file +29
-0@@ -0,0 +1,29 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2020 Rockchip Electronics Co., Ltd. + */ + +/dts-v1/; +#include "rv1126.dtsi" +#include "rv1126-sonoff-ihost.dtsi" + +/ { + model = "Sonoff iHost 4G"; + compatible = "itead,sonoff-ihost", "rockchip,rv1126"; +}; + +&cpu0 { + cpu-supply = <&vdd_arm>; +}; + +&cpu1 { + cpu-supply = <&vdd_arm>; +}; + +&cpu2 { + cpu-supply = <&vdd_arm>; +}; + +&cpu3 { + cpu-supply = <&vdd_arm>; +};arch/arm/dts/rv1126-sonoff-ihost.dtsi new file +404
-0@@ -0,0 +1,404 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2020 Rockchip Electronics Co., Ltd. + * Copyright (c) 2022 Edgeble AI Technologies Pvt. Ltd. + */ + +/ { + aliases { + ethernet0 = &gmac; + mmc0 = &emmc; + }; + + chosen { + stdout-path = "serial2:1500000n8"; + }; + + vcc5v0_sys: regulator-vcc5v0-sys { + compatible = "regulator-fixed"; + regulator-name = "vcc5v0_sys"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + sdio_pwrseq: pwrseq-sdio { + compatible = "mmc-pwrseq-simple"; + clocks = <&rk809 1>; + clock-names = "ext_clock"; + pinctrl-names = "default"; + pinctrl-0 = <&wifi_enable_h>; + reset-gpios = <&gpio1 RK_PD0 GPIO_ACTIVE_LOW>; + }; +}; + +&emmc { + bus-width = <8>; + cap-mmc-highspeed; + mmc-hs200-1_8v; + non-removable; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_bus8 &emmc_cmd &emmc_clk &emmc_rstnout>; + rockchip,default-sample-phase = <90>; + vmmc-supply = <&vcc_3v3>; + vqmmc-supply = <&vcc_1v8>; + status = "okay"; +}; + +&i2c0 { + clock-frequency = <400000>; + status = "okay"; + + rk809: pmic@20 { + compatible = "rockchip,rk809"; + reg = <0x20>; + interrupt-parent = <&gpio0>; + interrupts = <RK_PB1 IRQ_TYPE_LEVEL_LOW>; + #clock-cells = <1>; + clock-output-names = "rk808-clkout1", "rk808-clkout2"; + pinctrl-names = "default"; + pinctrl-0 = <&pmic_int_l>; + rockchip,system-power-controller; + wakeup-source; + + vcc1-supply = <&vcc5v0_sys>; + vcc2-supply = <&vcc5v0_sys>; + vcc3-supply = <&vcc5v0_sys>; + vcc4-supply = <&vcc5v0_sys>; + vcc5-supply = <&vcc_buck5>; + vcc6-supply = <&vcc_buck5>; + vcc7-supply = <&vcc5v0_sys>; + vcc8-supply = <&vcc3v3_sys>; + vcc9-supply = <&vcc5v0_sys>; + + regulators { + vdd_npu_vepu: DCDC_REG1 { + regulator-name = "vdd_npu_vepu"; + regulator-always-on; + regulator-boot-on; + regulator-initial-mode = <0x2>; + regulator-min-microvolt = <650000>; + regulator-max-microvolt = <950000>; + regulator-ramp-delay = <6001>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdd_arm: DCDC_REG2 { + regulator-name = "vdd_arm"; + regulator-always-on; + regulator-boot-on; + regulator-initial-mode = <0x2>; + regulator-min-microvolt = <725000>; + regulator-max-microvolt = <1350000>; + regulator-ramp-delay = <6001>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc_ddr: DCDC_REG3 { + regulator-name = "vcc_ddr"; + regulator-always-on; + regulator-boot-on; + regulator-initial-mode = <0x2>; + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + + vcc3v3_sys: DCDC_REG4 { + regulator-name = "vcc3v3_sys"; + regulator-always-on; + regulator-boot-on; + regulator-initial-mode = <0x2>; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <3300000>; + }; + }; + + vcc_buck5: DCDC_REG5 { + regulator-name = "vcc_buck5"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <2200000>; + regulator-max-microvolt = <2200000>; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <2200000>; + }; + }; + + vcc_0v8: LDO_REG1 { + regulator-name = "vcc_0v8"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <800000>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc1v8_pmu: LDO_REG2 { + regulator-name = "vcc1v8_pmu"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1800000>; + }; + }; + + vdd0v8_pmu: LDO_REG3 { + regulator-name = "vcc0v8_pmu"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <800000>; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <800000>; + }; + }; + + vcc_1v8: LDO_REG4 { + regulator-name = "vcc_1v8"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1800000>; + }; + }; + + vcc_dovdd: LDO_REG5 { + regulator-name = "vcc_dovdd"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc_dvdd: LDO_REG6 { + regulator-name = "vcc_dvdd"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc_avdd: LDO_REG7 { + regulator-name = "vcc_avdd"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vccio_sd: LDO_REG8 { + regulator-name = "vccio_sd"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc3v3_sd: LDO_REG9 { + regulator-name = "vcc3v3_sd"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc_5v0: SWITCH_REG1 { + regulator-name = "vcc_5v0"; + }; + + vcc_3v3: SWITCH_REG2 { + regulator-name = "vcc_3v3"; + regulator-always-on; + regulator-boot-on; + }; + }; + }; +}; + +&i2c2 { + status = "okay"; + clock-frequency = <400000>; + + pcf8563: rtc@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + #clock-cells = <0>; + interrupt-parent = <&gpio0>; + interrupts = <RK_PA2 IRQ_TYPE_LEVEL_LOW>; + clock-output-names = "xin32k"; + }; +}; + +&gmac { + assigned-clocks = <&cru CLK_GMAC_SRC_M1>, <&cru CLK_GMAC_SRC>, + <&cru CLK_GMAC_TX_RX>; + assigned-clock-parents = <&cru CLK_GMAC_RGMII_M1>, <&cru CLK_GMAC_SRC_M1>, + <&cru RMII_MODE_CLK>; + assigned-clock-rates = <0>, <50000000>; + clock_in_out = "output"; + phy-handle = <&phy>; + phy-mode = "rmii"; + phy-supply = <&vcc_3v3>; + pinctrl-names = "default"; + pinctrl-0 = <&rgmiim1_miim &rgmiim1_rxer &rgmiim1_bus2 &rgmiim1_mclkinout>; + status = "okay"; +}; + +&mdio { + phy: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0x0>; + pinctrl-names = "default"; + pinctrl-0 = <ð_phy_rst>; + reset-active-low; + reset-assert-us = <50000>; + reset-deassert-us = <10000>; + reset-gpios = <&gpio2 RK_PA6 GPIO_ACTIVE_LOW>; + }; +}; + +&pinctrl { + ethernet { + eth_phy_rst: eth-phy-rst { + rockchip,pins = <2 RK_PA6 RK_FUNC_GPIO &pcfg_pull_down>; + }; + }; + bt { + bt_enable: bt-enable { + rockchip,pins = <1 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + bt_wake_dev: bt-wake-dev { + rockchip,pins = <1 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + bt_wake_host: bt-wake-host { + rockchip,pins = <1 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + pmic { + pmic_int_l: pmic-int-l { + rockchip,pins = <0 RK_PB1 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + wifi { + wifi_enable_h: wifi-enable-h { + rockchip,pins = <1 RK_PD0 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; +}; + +&pmu_io_domains { + pmuio0-supply = <&vcc1v8_pmu>; + pmuio1-supply = <&vcc3v3_sys>; + vccio1-supply = <&vcc_1v8>; + vccio2-supply = <&vccio_sd>; + vccio3-supply = <&vcc_1v8>; + vccio4-supply = <&vcc_dovdd>; + vccio5-supply = <&vcc_1v8>; + vccio6-supply = <&vcc_1v8>; + vccio7-supply = <&vcc_dovdd>; + status = "okay"; +}; + +&saradc { + vref-supply = <&vcc_1v8>; + status = "okay"; +}; + +&sdio { + bus-width = <4>; + cap-sd-highspeed; + cap-sdio-irq; + keep-power-in-suspend; + max-frequency = <100000000>; + mmc-pwrseq = <&sdio_pwrseq>; + non-removable; + pinctrl-names = "default"; + pinctrl-0 = <&sdmmc1_clk &sdmmc1_cmd &sdmmc1_bus4>; + rockchip,default-sample-phase = <90>; + sd-uhs-sdr104; + vmmc-supply = <&vcc3v3_sys>; + vqmmc-supply = <&vcc_1v8>; + status = "okay"; +}; + +&sdmmc { + bus-width = <4>; + cap-mmc-highspeed; + cap-sd-highspeed; + card-detect-delay = <200>; + pinctrl-names = "default"; + pinctrl-0 = <&sdmmc0_clk &sdmmc0_cmd &sdmmc0_bus4 &sdmmc0_det>; + rockchip,default-sample-phase = <90>; + sd-uhs-sdr12; + sd-uhs-sdr25; + sd-uhs-sdr104; + vqmmc-supply = <&vccio_sd>; + status = "okay"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_xfer &uart0_ctsn &uart0_rtsn>; + uart-has-rtscts; + status = "okay"; + + bluetooth { + compatible = "realtek,rtl8723ds-bt"; + device-wake-gpios = <&gpio1 RK_PC7 GPIO_ACTIVE_HIGH>; /* BT_WAKE */ + enable-gpios = <&gpio1 RK_PC6 GPIO_ACTIVE_HIGH>; /* BT_RST */ + host-wake-gpios = <&gpio1 RK_PC5 GPIO_ACTIVE_HIGH>; /* BT_WAKE_HOST */ + max-speed = <2000000>; + pinctrl-names = "default"; + pinctrl-0 = <&bt_enable>, <&bt_wake_dev>, <&bt_wake_host>; + }; +}; + +&uart2 { + status = "okay"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3m2_xfer>; + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&uart4m2_xfer>; + status = "okay"; +};arch/arm/dts/rv1126.dtsi +185
-0@@ -21,6 +21,13 @@ aliases { i2c0 = &i2c0; + i2c2 = &i2c2; + serial0 = &uart0; + serial1 = &uart1; + serial2 = &uart2; + serial3 = &uart3; + serial4 = &uart4; + serial5 = &uart5; }; cpus {@@ -83,6 +90,11 @@ clock-frequency = <24000000>; }; + display_subsystem { + compatible = "rockchip,display-subsystem"; + ports = <&vop_out>; + }; + xin24m: oscillator { compatible = "fixed-clock"; clock-frequency = <24000000>;@@ -125,6 +137,26 @@ reg = <0xfe86c000 0x20>; }; + qos_iep: qos@fe8a0000 { + compatible = "rockchip,rv1126-qos", "syscon"; + reg = <0xfe8a0000 0x20>; + }; + + qos_rga_rd: qos@fe8a0080 { + compatible = "rockchip,rv1126-qos", "syscon"; + reg = <0xfe8a0080 0x20>; + }; + + qos_rga_wr: qos@fe8a0100 { + compatible = "rockchip,rv1126-qos", "syscon"; + reg = <0xfe8a0100 0x20>; + }; + + qos_vop: qos@fe8a0180 { + compatible = "rockchip,rv1126-qos", "syscon"; + reg = <0xfe8a0180 0x20>; + }; + gic: interrupt-controller@feff0000 { compatible = "arm,gic-400"; interrupt-controller;@@ -170,6 +202,25 @@ pm_qos = <&qos_sdio>; #power-domain-cells = <0>; }; + + power-domain@RV1126_PD_VO { + reg = <RV1126_PD_VO>; + clocks = <&cru ACLK_RGA>, + <&cru HCLK_RGA>, + <&cru CLK_RGA_CORE>, + <&cru ACLK_VOP>, + <&cru HCLK_VOP>, + <&cru DCLK_VOP>, + <&cru PCLK_DSIHOST>, + <&cru ACLK_IEP>, + <&cru HCLK_IEP>, + <&cru CLK_IEP_CORE>; + pm_qos = <&qos_rga_rd>, + <&qos_rga_wr>, + <&qos_vop>, + <&qos_iep>; + #power-domain-cells = <0>; + }; }; };@@ -187,6 +238,20 @@ status = "disabled"; }; + i2c2: i2c@ff400000 { + compatible = "rockchip,rv1126-i2c", "rockchip,rk3399-i2c"; + reg = <0xff400000 0x1000>; + interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; + rockchip,grf = <&pmugrf>; + clocks = <&pmucru CLK_I2C2>, <&pmucru PCLK_I2C2>; + clock-names = "i2c", "pclk"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_xfer>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + uart1: serial@ff410000 { compatible = "rockchip,rv1126-uart", "snps,dw-apb-uart"; reg = <0xff410000 0x100>;@@ -203,6 +268,17 @@ status = "disabled"; }; + pwm2: pwm@ff430020 { + compatible = "rockchip,rv1126-pwm", "rockchip,rk3328-pwm"; + reg = <0xff430020 0x10>; + clock-names = "pwm", "pclk"; + clocks = <&pmucru CLK_PWM0>, <&pmucru PCLK_PWM0>; + pinctrl-names = "default"; + pinctrl-0 = <&pwm2m0_pins>; + #pwm-cells = <3>; + status = "disabled"; + }; + pmucru: clock-controller@ff480000 { compatible = "rockchip,rv1126-pmucru"; reg = <0xff480000 0x1000>;@@ -232,6 +308,17 @@ clock-names = "apb_pclk"; }; + pwm11: pwm@ff550030 { + compatible = "rockchip,rv1126-pwm", "rockchip,rk3328-pwm"; + reg = <0xff550030 0x10>; + clock-names = "pwm", "pclk"; + clocks = <&cru CLK_PWM2>, <&cru PCLK_PWM2>; + pinctrl-0 = <&pwm11m0_pins>; + pinctrl-names = "default"; + #pwm-cells = <3>; + status = "disabled"; + }; + uart0: serial@ff560000 { compatible = "rockchip,rv1126-uart", "snps,dw-apb-uart"; reg = <0xff560000 0x100>;@@ -332,6 +419,92 @@ clock-names = "pclk", "timer"; }; + vop: vop@ffb00000 { + compatible = "rockchip,rv1126-vop"; + reg = <0xffb00000 0x200>, <0xffb00a00 0x400>; + interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "aclk_vop", "dclk_vop", "hclk_vop"; + clocks = <&cru ACLK_VOP>, <&cru DCLK_VOP>, <&cru HCLK_VOP>; + reset-names = "axi", "ahb", "dclk"; + resets = <&cru SRST_VOP_A>, <&cru SRST_VOP_H>, <&cru SRST_VOP_D>; + iommus = <&vop_mmu>; + power-domains = <&power RV1126_PD_VO>; + status = "disabled"; + + vop_out: port { + #address-cells = <1>; + #size-cells = <0>; + + vop_out_rgb: endpoint@0 { + reg = <0>; + }; + + vop_out_dsi: endpoint@1 { + reg = <1>; + }; + }; + }; + + vop_mmu: iommu@ffb00f00 { + compatible = "rockchip,iommu"; + reg = <0xffb00f00 0x100>; + interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "aclk", "iface"; + clocks = <&cru ACLK_VOP>, <&cru HCLK_VOP>; + #iommu-cells = <0>; + power-domains = <&power RV1126_PD_VO>; + status = "disabled"; + }; + + gmac: ethernet@ffc40000 { + compatible = "rockchip,rv1126-gmac", "snps,dwmac-4.20a"; + reg = <0xffc40000 0x4000>; + interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq", "eth_wake_irq"; + rockchip,grf = <&grf>; + clocks = <&cru CLK_GMAC_SRC>, <&cru CLK_GMAC_TX_RX>, + <&cru CLK_GMAC_TX_RX>, <&cru CLK_GMAC_REF>, + <&cru ACLK_GMAC>, <&cru PCLK_GMAC>, + <&cru CLK_GMAC_TX_RX>, <&cru CLK_GMAC_PTPREF>; + clock-names = "stmmaceth", "mac_clk_rx", + "mac_clk_tx", "clk_mac_ref", + "aclk_mac", "pclk_mac", + "clk_mac_speed", "ptp_ref"; + resets = <&cru SRST_GMAC_A>; + reset-names = "stmmaceth"; + + snps,mixed-burst; + snps,tso; + + snps,axi-config = <&stmmac_axi_setup>; + snps,mtl-rx-config = <&mtl_rx_setup>; + snps,mtl-tx-config = <&mtl_tx_setup>; + status = "disabled"; + + mdio: mdio { + compatible = "snps,dwmac-mdio"; + #address-cells = <0x1>; + #size-cells = <0x0>; + }; + + stmmac_axi_setup: stmmac-axi-config { + snps,wr_osr_lmt = <4>; + snps,rd_osr_lmt = <8>; + snps,blen = <0 0 0 0 16 8 4>; + }; + + mtl_rx_setup: rx-queues-config { + snps,rx-queues-to-use = <1>; + queue0 {}; + }; + + mtl_tx_setup: tx-queues-config { + snps,tx-queues-to-use = <1>; + queue0 {}; + }; + }; + emmc: mmc@ffc50000 { compatible = "rockchip,rv1126-dw-mshc", "rockchip,rk3288-dw-mshc"; reg = <0xffc50000 0x4000>;@@ -370,6 +543,18 @@ status = "disabled"; }; + sfc: spi@ffc90000 { + compatible = "rockchip,sfc"; + reg = <0xffc90000 0x4000>; + interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>; + assigned-clocks = <&cru SCLK_SFC>; + assigned-clock-rates = <80000000>; + clock-names = "clk_sfc", "hclk_sfc"; + clocks = <&cru SCLK_SFC>, <&cru HCLK_SFC>; + power-domains = <&power RV1126_PD_NVM>; + status = "disabled"; + }; + pinctrl: pinctrl { compatible = "rockchip,rv1126-pinctrl"; rockchip,grf = <&grf>;
PATCH v2 2/6 ram: rockchip: Add rv1126 ddr4 support
In reply to Tim LunnAdd support for ddr4 on rv1126. Timing detection files are imported from downstream Rockchip BSP u-boot. Allow selecting ddr4 ram with define CONFIG_RAM_ROCKCHIP_DDR4.
---
(no changes since v1)
.../sdram-rv1126-ddr4-detect-1056.inc | 75 +++++++++++++++++++ .../rockchip/sdram-rv1126-ddr4-detect-328.inc | 75 +++++++++++++++++++ .../rockchip/sdram-rv1126-ddr4-detect-396.inc | 75 +++++++++++++++++++ .../rockchip/sdram-rv1126-ddr4-detect-528.inc | 75 +++++++++++++++++++ .../rockchip/sdram-rv1126-ddr4-detect-664.inc | 75 +++++++++++++++++++ .../rockchip/sdram-rv1126-ddr4-detect-784.inc | 75 +++++++++++++++++++ .../rockchip/sdram-rv1126-ddr4-detect-924.inc | 75 +++++++++++++++++++ drivers/ram/rockchip/sdram_rv1126.c | 8 ++ 8 files changed, 533 insertions(+) create mode 100644 drivers/ram/rockchip/sdram-rv1126-ddr4-detect-1056.inc create mode 100644 drivers/ram/rockchip/sdram-rv1126-ddr4-detect-328.inc create mode 100644 drivers/ram/rockchip/sdram-rv1126-ddr4-detect-396.inc create mode 100644 drivers/ram/rockchip/sdram-rv1126-ddr4-detect-528.inc create mode 100644 drivers/ram/rockchip/sdram-rv1126-ddr4-detect-664.inc create mode 100644 drivers/ram/rockchip/sdram-rv1126-ddr4-detect-784.inc create mode 100644 drivers/ram/rockchip/sdram-rv1126-ddr4-detect-924.inc
drivers/ram/rockchip/sdram-rv1126-ddr4-detect-1056.inc new file +75 -0
@@ -0,0 +1,75 @@ +{ + { + { + .rank = 0x1, + .col = 0xA, + .bk = 0x2, + .bw = 0x1, + .dbw = 0x0, + .row_3_4 = 0x0, + .cs0_row = 0x11, + .cs1_row = 0x0, + .cs0_high16bit_row = 0x11, + .cs1_high16bit_row = 0x0, + .ddrconfig = 0 + }, + { + {0x561d1219}, + {0x10030703}, + {0x00000002}, + {0x00001111}, + {0x0000000c}, + {0x0000034b}, + 0x000000ff + } + }, + { + .ddr_freq = 1056, /* clock rate(MHz) */ + .dramtype = DDR4, + .num_channels = 1, + .stride = 0, + .odt = 1 + }, + { + { + {0x00000000, 0x43041010}, /* MSTR */ + {0x00000064, 0x008000b9}, /* RFSHTMG */ + {0x000000d0, 0x00020103}, /* INIT0 */ + {0x000000d4, 0x00690000}, /* INIT1 */ + {0x000000d8, 0x00000100}, /* INIT2 */ + {0x000000dc, 0x07340401}, /* INIT3 */ + {0x000000e0, 0x00100000}, /* INIT4 */ + {0x000000e4, 0x00110000}, /* INIT5 */ + {0x000000e8, 0x00000420}, /* INIT6 */ + {0x000000ec, 0x00000800}, /* INIT7 */ + {0x000000f4, 0x000f011f}, /* RANKCTL */ + {0x00000100, 0x0f102411}, /* DRAMTMG0 */ + {0x00000104, 0x0004041a}, /* DRAMTMG1 */ + {0x00000108, 0x0608060d}, /* DRAMTMG2 */ + {0x0000010c, 0x0040400c}, /* DRAMTMG3 */ + {0x00000110, 0x08030409}, /* DRAMTMG4 */ + {0x00000114, 0x06060403}, /* DRAMTMG5 */ + {0x00000120, 0x07070d07}, /* DRAMTMG8 */ + {0x00000124, 0x00020309}, /* DRAMTMG9 */ + {0x00000180, 0x01000040}, /* ZQCTL0 */ + {0x00000184, 0x00000000}, /* ZQCTL1 */ + {0x00000190, 0x07060004}, /* DFITMG0 */ + {0x00000198, 0x07000101}, /* DFILPCFG0 */ + {0x000001a0, 0xc0400003}, /* DFIUPD0 */ + {0x00000240, 0x06000614}, /* ODTCFG */ + {0x00000244, 0x00000201}, /* ODTMAP */ + {0x00000250, 0x00001f00}, /* SCHED */ + {0x00000490, 0x00000001}, /* PCTRL_0 */ + {0xffffffff, 0xffffffff} + } + }, + { + { + {0x00000004, 0x0000008c}, /* PHYREG01 */ + {0x00000014, 0x00000010}, /* PHYREG05 */ + {0x00000018, 0x00000000}, /* PHYREG06 */ + {0x0000001c, 0x0000000b}, /* PHYREG07 */ + {0xffffffff, 0xffffffff} + } + } +},
drivers/ram/rockchip/sdram-rv1126-ddr4-detect-328.inc new file +75 -0
75 lines not on this page · raw message
drivers/ram/rockchip/sdram-rv1126-ddr4-detect-396.inc new file +75 -0
75 lines not on this page · raw message
drivers/ram/rockchip/sdram-rv1126-ddr4-detect-528.inc new file +75 -0
75 lines not on this page · raw message
drivers/ram/rockchip/sdram-rv1126-ddr4-detect-664.inc new file +75 -0
75 lines not on this page · raw message
drivers/ram/rockchip/sdram-rv1126-ddr4-detect-784.inc new file +75 -0
75 lines not on this page · raw message
drivers/ram/rockchip/sdram-rv1126-ddr4-detect-924.inc new file +75 -0
75 lines not on this page · raw message
drivers/ram/rockchip/sdram_rv1126.c +8 -0
@@ -76,6 +76,14 @@ struct rv1126_sdram_params sdram_configs[] = {# include "sdram-rv1126-lpddr4-detect-784.inc" # include "sdram-rv1126-lpddr4-detect-924.inc" # include "sdram-rv1126-lpddr4-detect-1056.inc" +#elif defined(CONFIG_RAM_ROCKCHIP_DDR4 ) +# include "sdram-rv1126-ddr4-detect-328.inc" +# include "sdram-rv1126-ddr4-detect-396.inc" +# include "sdram-rv1126-ddr4-detect-528.inc" +# include "sdram-rv1126-ddr4-detect-664.inc" +# include "sdram-rv1126-ddr4-detect-784.inc" +# include "sdram-rv1126-ddr4-detect-924.inc" +# include "sdram-rv1126-ddr4-detect-1056.inc" #else # include "sdram-rv1126-ddr3-detect-328.inc" # include "sdram-rv1126-ddr3-detect-396.inc"
Signature · 1 line
2.40.1
Re: [PATCH v2 2/6] ram: rockchip: Add rv1126 ddr4 support
Quoted 5 lines · Tim Lunn
Add support for ddr4 on rv1126. Timing detection files are imported from downstream Rockchip BSP u-boot. Allow selecting ddr4 ram with define
CONFIG_RAM_ROCKCHIP_DDR4.Signed-off-by Tim Lunn <[email protected]>
Thanks,
- Kever
Quoted 607 lines
---
(no changes since v1)
.../sdram-rv1126-ddr4-detect-1056.inc | 75 +++++++++++++++++++ .../rockchip/sdram-rv1126-ddr4-detect-328.inc | 75 +++++++++++++++++++ .../rockchip/sdram-rv1126-ddr4-detect-396.inc | 75 +++++++++++++++++++ .../rockchip/sdram-rv1126-ddr4-detect-528.inc | 75 +++++++++++++++++++ .../rockchip/sdram-rv1126-ddr4-detect-664.inc | 75 +++++++++++++++++++ .../rockchip/sdram-rv1126-ddr4-detect-784.inc | 75 +++++++++++++++++++ .../rockchip/sdram-rv1126-ddr4-detect-924.inc | 75 +++++++++++++++++++ drivers/ram/rockchip/sdram_rv1126.c | 8 ++ 8 files changed, 533 insertions(+)create mode 100644
drivers/ram/rockchip/sdram-rv1126-ddr4-detect-1056.inccreate mode 100644drivers/ram/rockchip/sdram-rv1126-ddr4-detect-328.inccreate mode 100644drivers/ram/rockchip/sdram-rv1126-ddr4-detect-396.inccreate mode 100644drivers/ram/rockchip/sdram-rv1126-ddr4-detect-528.inccreate mode 100644drivers/ram/rockchip/sdram-rv1126-ddr4-detect-664.inccreate mode 100644drivers/ram/rockchip/sdram-rv1126-ddr4-detect-784.inccreate mode 100644drivers/ram/rockchip/sdram-rv1126-ddr4-detect-924.incdrivers/ram/rockchip/sdram-rv1126-ddr4-detect-1056.inc new file +75
-0@@ -0,0 +1,75 @@ +{ + { + { + .rank = 0x1, + .col = 0xA, + .bk = 0x2, + .bw = 0x1, + .dbw = 0x0, + .row_3_4 = 0x0, + .cs0_row = 0x11, + .cs1_row = 0x0, + .cs0_high16bit_row = 0x11, + .cs1_high16bit_row = 0x0, + .ddrconfig = 0 + }, + { + {0x561d1219}, + {0x10030703}, + {0x00000002}, + {0x00001111}, + {0x0000000c}, + {0x0000034b}, + 0x000000ff + } + }, + { + .ddr_freq = 1056, /* clock rate(MHz) */ + .dramtype = DDR4, + .num_channels = 1, + .stride = 0, + .odt = 1 + }, + { + { + {0x00000000, 0x43041010}, /* MSTR */ + {0x00000064, 0x008000b9}, /* RFSHTMG */ + {0x000000d0, 0x00020103}, /* INIT0 */ + {0x000000d4, 0x00690000}, /* INIT1 */ + {0x000000d8, 0x00000100}, /* INIT2 */ + {0x000000dc, 0x07340401}, /* INIT3 */ + {0x000000e0, 0x00100000}, /* INIT4 */ + {0x000000e4, 0x00110000}, /* INIT5 */ + {0x000000e8, 0x00000420}, /* INIT6 */ + {0x000000ec, 0x00000800}, /* INIT7 */ + {0x000000f4, 0x000f011f}, /* RANKCTL */ + {0x00000100, 0x0f102411}, /* DRAMTMG0 */ + {0x00000104, 0x0004041a}, /* DRAMTMG1 */ + {0x00000108, 0x0608060d}, /* DRAMTMG2 */ + {0x0000010c, 0x0040400c}, /* DRAMTMG3 */ + {0x00000110, 0x08030409}, /* DRAMTMG4 */ + {0x00000114, 0x06060403}, /* DRAMTMG5 */ + {0x00000120, 0x07070d07}, /* DRAMTMG8 */ + {0x00000124, 0x00020309}, /* DRAMTMG9 */ + {0x00000180, 0x01000040}, /* ZQCTL0 */ + {0x00000184, 0x00000000}, /* ZQCTL1 */ + {0x00000190, 0x07060004}, /* DFITMG0 */ + {0x00000198, 0x07000101}, /* DFILPCFG0 */ + {0x000001a0, 0xc0400003}, /* DFIUPD0 */ + {0x00000240, 0x06000614}, /* ODTCFG */ + {0x00000244, 0x00000201}, /* ODTMAP */ + {0x00000250, 0x00001f00}, /* SCHED */ + {0x00000490, 0x00000001}, /* PCTRL_0 */ + {0xffffffff, 0xffffffff} + } + }, + { + { + {0x00000004, 0x0000008c}, /* PHYREG01 */ + {0x00000014, 0x00000010}, /* PHYREG05 */ + {0x00000018, 0x00000000}, /* PHYREG06 */ + {0x0000001c, 0x0000000b}, /* PHYREG07 */ + {0xffffffff, 0xffffffff} + } + } +},drivers/ram/rockchip/sdram-rv1126-ddr4-detect-328.inc new file +75
-0@@ -0,0 +1,75 @@ +{ + { + { + .rank = 0x1, + .col = 0xA, + .bk = 0x2, + .bw = 0x1, + .dbw = 0x0, + .row_3_4 = 0x0, + .cs0_row = 0x11, + .cs1_row = 0x0, + .cs0_high16bit_row = 0x11, + .cs1_high16bit_row = 0x0, + .ddrconfig = 0 + }, + { + {0x4d110a08}, + {0x06020501}, + {0x00000002}, + {0x00001111}, + {0x0000000c}, + {0x00000232}, + 0x000000ff + } + }, + { + .ddr_freq = 328, /* clock rate(MHz) */ + .dramtype = DDR4, + .num_channels = 1, + .stride = 0, + .odt = 0 + }, + { + { + {0x00000000, 0x43049010}, /* MSTR */ + {0x00000064, 0x0027003a}, /* RFSHTMG */ + {0x000000d0, 0x00020052}, /* INIT0 */ + {0x000000d4, 0x00220000}, /* INIT1 */ + {0x000000d8, 0x00000100}, /* INIT2 */ + {0x000000dc, 0x00040000}, /* INIT3 */ + {0x000000e0, 0x00000000}, /* INIT4 */ + {0x000000e4, 0x00110000}, /* INIT5 */ + {0x000000e8, 0x00000420}, /* INIT6 */ + {0x000000ec, 0x00000400}, /* INIT7 */ + {0x000000f4, 0x000f011f}, /* RANKCTL */ + {0x00000100, 0x09060b06}, /* DRAMTMG0 */ + {0x00000104, 0x00020209}, /* DRAMTMG1 */ + {0x00000108, 0x0505040a}, /* DRAMTMG2 */ + {0x0000010c, 0x0040400c}, /* DRAMTMG3 */ + {0x00000110, 0x05030206}, /* DRAMTMG4 */ + {0x00000114, 0x03030202}, /* DRAMTMG5 */ + {0x00000120, 0x03030b03}, /* DRAMTMG8 */ + {0x00000124, 0x00020208}, /* DRAMTMG9 */ + {0x00000180, 0x01000040}, /* ZQCTL0 */ + {0x00000184, 0x00000000}, /* ZQCTL1 */ + {0x00000190, 0x07030003}, /* DFITMG0 */ + {0x00000198, 0x07000101}, /* DFILPCFG0 */ + {0x000001a0, 0xc0400003}, /* DFIUPD0 */ + {0x00000240, 0x06000604}, /* ODTCFG */ + {0x00000244, 0x00000201}, /* ODTMAP */ + {0x00000250, 0x00001f00}, /* SCHED */ + {0x00000490, 0x00000001}, /* PCTRL_0 */ + {0xffffffff, 0xffffffff} + } + }, + { + { + {0x00000004, 0x0000008c}, /* PHYREG01 */ + {0x00000014, 0x0000000a}, /* PHYREG05 */ + {0x00000018, 0x00000000}, /* PHYREG06 */ + {0x0000001c, 0x00000009}, /* PHYREG07 */ + {0xffffffff, 0xffffffff} + } + } +},drivers/ram/rockchip/sdram-rv1126-ddr4-detect-396.inc new file +75
-0@@ -0,0 +1,75 @@ +{ + { + { + .rank = 0x1, + .col = 0xA, + .bk = 0x2, + .bw = 0x1, + .dbw = 0x0, + .row_3_4 = 0x0, + .cs0_row = 0x11, + .cs1_row = 0x0, + .cs0_high16bit_row = 0x11, + .cs1_high16bit_row = 0x0, + .ddrconfig = 0 + }, + { + {0x4d110a0a}, + {0x07020501}, + {0x00000002}, + {0x00001111}, + {0x0000000c}, + {0x00000232}, + 0x000000ff + } + }, + { + .ddr_freq = 396, /* clock rate(MHz) */ + .dramtype = DDR4, + .num_channels = 1, + .stride = 0, + .odt = 0 + }, + { + { + {0x00000000, 0x43049010}, /* MSTR */ + {0x00000064, 0x00300046}, /* RFSHTMG */ + {0x000000d0, 0x00020062}, /* INIT0 */ + {0x000000d4, 0x00280000}, /* INIT1 */ + {0x000000d8, 0x00000100}, /* INIT2 */ + {0x000000dc, 0x00040000}, /* INIT3 */ + {0x000000e0, 0x00000000}, /* INIT4 */ + {0x000000e4, 0x00110000}, /* INIT5 */ + {0x000000e8, 0x00000420}, /* INIT6 */ + {0x000000ec, 0x00000400}, /* INIT7 */ + {0x000000f4, 0x000f011f}, /* RANKCTL */ + {0x00000100, 0x09070d07}, /* DRAMTMG0 */ + {0x00000104, 0x0002020a}, /* DRAMTMG1 */ + {0x00000108, 0x0505040a}, /* DRAMTMG2 */ + {0x0000010c, 0x0040400c}, /* DRAMTMG3 */ + {0x00000110, 0x05030206}, /* DRAMTMG4 */ + {0x00000114, 0x03030202}, /* DRAMTMG5 */ + {0x00000120, 0x04040b04}, /* DRAMTMG8 */ + {0x00000124, 0x00020208}, /* DRAMTMG9 */ + {0x00000180, 0x01000040}, /* ZQCTL0 */ + {0x00000184, 0x00000000}, /* ZQCTL1 */ + {0x00000190, 0x07030003}, /* DFITMG0 */ + {0x00000198, 0x07000101}, /* DFILPCFG0 */ + {0x000001a0, 0xc0400003}, /* DFIUPD0 */ + {0x00000240, 0x06000604}, /* ODTCFG */ + {0x00000244, 0x00000201}, /* ODTMAP */ + {0x00000250, 0x00001f00}, /* SCHED */ + {0x00000490, 0x00000001}, /* PCTRL_0 */ + {0xffffffff, 0xffffffff} + } + }, + { + { + {0x00000004, 0x0000008c}, /* PHYREG01 */ + {0x00000014, 0x0000000a}, /* PHYREG05 */ + {0x00000018, 0x00000000}, /* PHYREG06 */ + {0x0000001c, 0x00000009}, /* PHYREG07 */ + {0xffffffff, 0xffffffff} + } + } +},drivers/ram/rockchip/sdram-rv1126-ddr4-detect-528.inc new file +75
-0@@ -0,0 +1,75 @@ +{ + { + { + .rank = 0x1, + .col = 0xA, + .bk = 0x2, + .bw = 0x1, + .dbw = 0x0, + .row_3_4 = 0x0, + .cs0_row = 0x11, + .cs1_row = 0x0, + .cs0_high16bit_row = 0x11, + .cs1_high16bit_row = 0x0, + .ddrconfig = 0 + }, + { + {0x4d120a0d}, + {0x09020501}, + {0x00000002}, + {0x00001111}, + {0x0000000c}, + {0x00000232}, + 0x000000ff + } + }, + { + .ddr_freq = 528, /* clock rate(MHz) */ + .dramtype = DDR4, + .num_channels = 1, + .stride = 0, + .odt = 0 + }, + { + { + {0x00000000, 0x43049010}, /* MSTR */ + {0x00000064, 0x0040005d}, /* RFSHTMG */ + {0x000000d0, 0x00020082}, /* INIT0 */ + {0x000000d4, 0x00350000}, /* INIT1 */ + {0x000000d8, 0x00000100}, /* INIT2 */ + {0x000000dc, 0x00040000}, /* INIT3 */ + {0x000000e0, 0x00000000}, /* INIT4 */ + {0x000000e4, 0x00110000}, /* INIT5 */ + {0x000000e8, 0x00000420}, /* INIT6 */ + {0x000000ec, 0x00000400}, /* INIT7 */ + {0x000000f4, 0x000f011f}, /* RANKCTL */ + {0x00000100, 0x0a0a1209}, /* DRAMTMG0 */ + {0x00000104, 0x0002020e}, /* DRAMTMG1 */ + {0x00000108, 0x0505040a}, /* DRAMTMG2 */ + {0x0000010c, 0x0040400c}, /* DRAMTMG3 */ + {0x00000110, 0x05030206}, /* DRAMTMG4 */ + {0x00000114, 0x03030202}, /* DRAMTMG5 */ + {0x00000120, 0x04040b04}, /* DRAMTMG8 */ + {0x00000124, 0x00020208}, /* DRAMTMG9 */ + {0x00000180, 0x01000040}, /* ZQCTL0 */ + {0x00000184, 0x00000000}, /* ZQCTL1 */ + {0x00000190, 0x07030003}, /* DFITMG0 */ + {0x00000198, 0x07000101}, /* DFILPCFG0 */ + {0x000001a0, 0xc0400003}, /* DFIUPD0 */ + {0x00000240, 0x06000604}, /* ODTCFG */ + {0x00000244, 0x00000201}, /* ODTMAP */ + {0x00000250, 0x00001f00}, /* SCHED */ + {0x00000490, 0x00000001}, /* PCTRL_0 */ + {0xffffffff, 0xffffffff} + } + }, + { + { + {0x00000004, 0x0000008c}, /* PHYREG01 */ + {0x00000014, 0x0000000a}, /* PHYREG05 */ + {0x00000018, 0x00000000}, /* PHYREG06 */ + {0x0000001c, 0x00000009}, /* PHYREG07 */ + {0xffffffff, 0xffffffff} + } + } +},drivers/ram/rockchip/sdram-rv1126-ddr4-detect-664.inc new file +75
-0@@ -0,0 +1,75 @@ +{ + { + { + .rank = 0x1, + .col = 0xA, + .bk = 0x2, + .bw = 0x1, + .dbw = 0x0, + .row_3_4 = 0x0, + .cs0_row = 0x11, + .cs1_row = 0x0, + .cs0_high16bit_row = 0x11, + .cs1_high16bit_row = 0x0, + .ddrconfig = 0 + }, + { + {0x4d130a11}, + {0x0c020501}, + {0x00000002}, + {0x00001111}, + {0x0000000c}, + {0x0000023a}, + 0x000000ff + } + }, + { + .ddr_freq = 664, /* clock rate(MHz) */ + .dramtype = DDR4, + .num_channels = 1, + .stride = 0, + .odt = 1 + }, + { + { + {0x00000000, 0x43041010}, /* MSTR */ + {0x00000064, 0x00500075}, /* RFSHTMG */ + {0x000000d0, 0x000200a4}, /* INIT0 */ + {0x000000d4, 0x00420000}, /* INIT1 */ + {0x000000d8, 0x00000100}, /* INIT2 */ + {0x000000dc, 0x01040401}, /* INIT3 */ + {0x000000e0, 0x00000000}, /* INIT4 */ + {0x000000e4, 0x00110000}, /* INIT5 */ + {0x000000e8, 0x00000420}, /* INIT6 */ + {0x000000ec, 0x00000400}, /* INIT7 */ + {0x000000f4, 0x000f011f}, /* RANKCTL */ + {0x00000100, 0x0b0c160c}, /* DRAMTMG0 */ + {0x00000104, 0x00020211}, /* DRAMTMG1 */ + {0x00000108, 0x0505040a}, /* DRAMTMG2 */ + {0x0000010c, 0x0040400c}, /* DRAMTMG3 */ + {0x00000110, 0x05030306}, /* DRAMTMG4 */ + {0x00000114, 0x04040302}, /* DRAMTMG5 */ + {0x00000120, 0x05050b05}, /* DRAMTMG8 */ + {0x00000124, 0x00020208}, /* DRAMTMG9 */ + {0x00000180, 0x01000040}, /* ZQCTL0 */ + {0x00000184, 0x00000000}, /* ZQCTL1 */ + {0x00000190, 0x07030003}, /* DFITMG0 */ + {0x00000198, 0x07000101}, /* DFILPCFG0 */ + {0x000001a0, 0xc0400003}, /* DFIUPD0 */ + {0x00000240, 0x06000604}, /* ODTCFG */ + {0x00000244, 0x00000201}, /* ODTMAP */ + {0x00000250, 0x00001f00}, /* SCHED */ + {0x00000490, 0x00000001}, /* PCTRL_0 */ + {0xffffffff, 0xffffffff} + } + }, + { + { + {0x00000004, 0x0000008c}, /* PHYREG01 */ + {0x00000014, 0x0000000a}, /* PHYREG05 */ + {0x00000018, 0x00000000}, /* PHYREG06 */ + {0x0000001c, 0x00000009}, /* PHYREG07 */ + {0xffffffff, 0xffffffff} + } + } +},drivers/ram/rockchip/sdram-rv1126-ddr4-detect-784.inc new file +75
-0@@ -0,0 +1,75 @@ +{ + { + { + .rank = 0x1, + .col = 0xA, + .bk = 0x2, + .bw = 0x1, + .dbw = 0x0, + .row_3_4 = 0x0, + .cs0_row = 0x11, + .cs1_row = 0x0, + .cs0_high16bit_row = 0x11, + .cs1_high16bit_row = 0x0, + .ddrconfig = 0 + }, + { + {0x50160d14}, + {0x0e020502}, + {0x00000002}, + {0x00001111}, + {0x0000000c}, + {0x0000033a}, + 0x000000ff + } + }, + { + .ddr_freq = 784, /* clock rate(MHz) */ + .dramtype = DDR4, + .num_channels = 1, + .stride = 0, + .odt = 1 + }, + { + { + {0x00000000, 0x43041010}, /* MSTR */ + {0x00000064, 0x005f008a}, /* RFSHTMG */ + {0x000000d0, 0x000200c1}, /* INIT0 */ + {0x000000d4, 0x004e0000}, /* INIT1 */ + {0x000000d8, 0x00000100}, /* INIT2 */ + {0x000000dc, 0x03140401}, /* INIT3 */ + {0x000000e0, 0x00000000}, /* INIT4 */ + {0x000000e4, 0x00110000}, /* INIT5 */ + {0x000000e8, 0x00000420}, /* INIT6 */ + {0x000000ec, 0x00000400}, /* INIT7 */ + {0x000000f4, 0x000f011f}, /* RANKCTL */ + {0x00000100, 0x0c0e1a0e}, /* DRAMTMG0 */ + {0x00000104, 0x00030314}, /* DRAMTMG1 */ + {0x00000108, 0x0506050b}, /* DRAMTMG2 */ + {0x0000010c, 0x0040400c}, /* DRAMTMG3 */ + {0x00000110, 0x06030307}, /* DRAMTMG4 */ + {0x00000114, 0x04040302}, /* DRAMTMG5 */ + {0x00000120, 0x06060b06}, /* DRAMTMG8 */ + {0x00000124, 0x00020308}, /* DRAMTMG9 */ + {0x00000180, 0x01000040}, /* ZQCTL0 */ + {0x00000184, 0x00000000}, /* ZQCTL1 */ + {0x00000190, 0x07040003}, /* DFITMG0 */ + {0x00000198, 0x07000101}, /* DFILPCFG0 */ + {0x000001a0, 0xc0400003}, /* DFIUPD0 */ + {0x00000240, 0x0600060c}, /* ODTCFG */ + {0x00000244, 0x00000201}, /* ODTMAP */ + {0x00000250, 0x00001f00}, /* SCHED */ + {0x00000490, 0x00000001}, /* PCTRL_0 */ + {0xffffffff, 0xffffffff} + } + }, + { + { + {0x00000004, 0x0000008c}, /* PHYREG01 */ + {0x00000014, 0x0000000c}, /* PHYREG05 */ + {0x00000018, 0x00000000}, /* PHYREG06 */ + {0x0000001c, 0x00000009}, /* PHYREG07 */ + {0xffffffff, 0xffffffff} + } + } +},drivers/ram/rockchip/sdram-rv1126-ddr4-detect-924.inc new file +75
-0@@ -0,0 +1,75 @@ +{ + { + { + .rank = 0x1, + .col = 0xA, + .bk = 0x2, + .bw = 0x1, + .dbw = 0x0, + .row_3_4 = 0x0, + .cs0_row = 0x11, + .cs1_row = 0x0, + .cs0_high16bit_row = 0x11, + .cs1_high16bit_row = 0x0, + .ddrconfig = 0 + }, + { + {0x531a0f17}, + {0x0e020603}, + {0x00000002}, + {0x00001111}, + {0x0000000c}, + {0x00000342}, + 0x000000ff + } + }, + { + .ddr_freq = 924, /* clock rate(MHz) */ + .dramtype = DDR4, + .num_channels = 1, + .stride = 0, + .odt = 1 + }, + { + { + {0x00000000, 0x43041010}, /* MSTR */ + {0x00000064, 0x007000a2}, /* RFSHTMG */ + {0x000000d0, 0x000200e3}, /* INIT0 */ + {0x000000d4, 0x005c0000}, /* INIT1 */ + {0x000000d8, 0x00000100}, /* INIT2 */ + {0x000000dc, 0x05240401}, /* INIT3 */ + {0x000000e0, 0x00080000}, /* INIT4 */ + {0x000000e4, 0x00110000}, /* INIT5 */ + {0x000000e8, 0x00000420}, /* INIT6 */ + {0x000000ec, 0x00000400}, /* INIT7 */ + {0x000000f4, 0x000f011f}, /* RANKCTL */ + {0x00000100, 0x0e0e1f10}, /* DRAMTMG0 */ + {0x00000104, 0x00030317}, /* DRAMTMG1 */ + {0x00000108, 0x0507050c}, /* DRAMTMG2 */ + {0x0000010c, 0x0040400c}, /* DRAMTMG3 */ + {0x00000110, 0x07030308}, /* DRAMTMG4 */ + {0x00000114, 0x05050303}, /* DRAMTMG5 */ + {0x00000120, 0x07070b07}, /* DRAMTMG8 */ + {0x00000124, 0x00020309}, /* DRAMTMG9 */ + {0x00000180, 0x01000040}, /* ZQCTL0 */ + {0x00000184, 0x00000000}, /* ZQCTL1 */ + {0x00000190, 0x07050003}, /* DFITMG0 */ + {0x00000198, 0x07000101}, /* DFILPCFG0 */ + {0x000001a0, 0xc0400003}, /* DFIUPD0 */ + {0x00000240, 0x06000610}, /* ODTCFG */ + {0x00000244, 0x00000201}, /* ODTMAP */ + {0x00000250, 0x00001f00}, /* SCHED */ + {0x00000490, 0x00000001}, /* PCTRL_0 */ + {0xffffffff, 0xffffffff} + } + }, + { + { + {0x00000004, 0x0000008c}, /* PHYREG01 */ + {0x00000014, 0x0000000e}, /* PHYREG05 */ + {0x00000018, 0x00000000}, /* PHYREG06 */ + {0x0000001c, 0x0000000a}, /* PHYREG07 */ + {0xffffffff, 0xffffffff} + } + } +},drivers/ram/rockchip/sdram_rv1126.c +8
-0@@ -76,6 +76,14 @@ struct rv1126_sdram_params sdram_configs[] = {# include "sdram-rv1126-lpddr4-detect-784.inc" # include "sdram-rv1126-lpddr4-detect-924.inc" # include "sdram-rv1126-lpddr4-detect-1056.inc" +#elif defined(CONFIG_RAM_ROCKCHIP_DDR4 ) +# include "sdram-rv1126-ddr4-detect-328.inc" +# include "sdram-rv1126-ddr4-detect-396.inc" +# include "sdram-rv1126-ddr4-detect-528.inc" +# include "sdram-rv1126-ddr4-detect-664.inc" +# include "sdram-rv1126-ddr4-detect-784.inc" +# include "sdram-rv1126-ddr4-detect-924.inc" +# include "sdram-rv1126-ddr4-detect-1056.inc" #else # include "sdram-rv1126-ddr3-detect-328.inc" # include "sdram-rv1126-ddr3-detect-396.inc"
PATCH v2 3/6 rockchip: Convert rv1126 to standard boot
In reply to Tim LunnRV1126 soc appears to have been missed with the conversion of rockchip socs to standard boot.
Remove remnants of distro boot for rv1126 common and the one existing board.
---
Changes in v2:
- New patch to clean up distro boot from rv1126_common.h
include/configs/neural-compute-module-2.h | 6 ------ include/configs/rv1126_common.h | 3 +-- 2 files changed, 1 insertion(+), 8 deletions(-)
include/configs/neural-compute-module-2.h +0 -6
@@ -12,10 +12,4 @@#include <configs/rv1126_common.h> -#undef BOOT_TARGET_DEVICES - -#define BOOT_TARGET_DEVICES (func) \ - func(MMC, mmc, 0) \ - func(MMC, mmc, 1) -#endif /* __NEURAL_COMPUTE_MODULE_2_H */
include/configs/rv1126_common.h +1 -2
@@ -28,7 +28,6 @@"kernel_addr_r=0x02008000\0" \"ramdisk_addr_r=0x0a200000\0" -#include <config_distro_bootcmd.h> #define CFG_EXTRA_ENV_SETTINGS \"fdt_high=0x0fffffff\0" \"initrd_high=0x0fffffff\0" \
@@ -36,6 +35,6 @@"partitions=" PARTS_DEFAULT \ENV_MEM_LAYOUT_SETTINGS \ROCKCHIP_DEVICE_SETTINGS \ - BOOTENV + "boot_targets=" BOOT_TARGETS "\0"#endif /* __CONFIG_RV1126_COMMON_H */
Signature · 1 line
2.40.1
Re: [PATCH v2 3/6] rockchip: Convert rv1126 to standard boot
Quoted 8 lines · Tim Lunn
RV1126 soc appears to have been missed with the conversion of rockchip socs to standard boot.
Remove remnants of distro boot for rv1126 common and the one existing board.
Thanks,
- Kever
Quoted 45 lines
---
Changes in v2:
- New patch to clean up distro boot fromrv1126_common.hinclude/configs/neural-compute-module-2.h | 6 ------ include/configs/rv1126_common.h | 3 +-- 2 files changed, 1 insertion(+), 8 deletions(-)include/configs/neural-compute-module-2.h +0
-6@@ -12,10 +12,4 @@#include <configs/rv1126_common.h> -#undef BOOT_TARGET_DEVICES - -#define BOOT_TARGET_DEVICES (func) \ - func(MMC, mmc, 0) \ - func(MMC, mmc, 1) -#endif /* __NEURAL_COMPUTE_MODULE_2_H */ include/configs/rv1126_common.h +1
-2@@ -28,7 +28,6 @@"kernel_addr_r=0x02008000\0" \"ramdisk_addr_r=0x0a200000\0" -#include <config_distro_bootcmd.h> #define CFG_EXTRA_ENV_SETTINGS \"fdt_high=0x0fffffff\0" \"initrd_high=0x0fffffff\0" \@@ -36,6 +35,6 @@"partitions=" PARTS_DEFAULT \ENV_MEM_LAYOUT_SETTINGS \ROCKCHIP_DEVICE_SETTINGS \ - BOOTENV + "boot_targets=" BOOT_TARGETS "\0"#endif /* __CONFIG_RV1126_COMMON_H */
PATCH v2 4/6 board: rockchip: Add Sonoff iHost board
In reply to Tim LunnSonoff iHost is gateway device designed to provide a Smart Home Hub, it is based on Rockchip RV1126. There is also a version with 2GB RAM based off the RV1109 dual core SoC however this works with the same config as the RV1126 for uboot purposes.
Features:
- Rockchip RV1126
- 4GB DDR4
- 8GB eMMC
- microSD slot
- RMII Ethernet PHY
- 1x USB 2.0 Host
- 1x USB 2.0 OTG
- Realtek RTL8723DS WiFi/BT
- EFR32MG21 Silabs Zigbee radio
- Speaker/Microphone
---
Changes in v2:
- Remove board config not required with standard boot
arch/arm/dts/rv1126-sonoff-ihost-u-boot.dtsi | 13 +++++ arch/arm/mach-rockchip/rv1126/Kconfig | 8 +++ board/itead/sonoff-ihost/Kconfig | 16 ++++++ board/itead/sonoff-ihost/MAINTAINERS | 6 ++ configs/sonoff-ihost-rv1126_defconfig | 60 ++++++++++++++++++++ doc/board/rockchip/rockchip.rst | 1 + include/configs/sonoff-ihost.h | 10 ++++ 7 files changed, 114 insertions(+) create mode 100644 arch/arm/dts/rv1126-sonoff-ihost-u-boot.dtsi create mode 100644 board/itead/sonoff-ihost/Kconfig create mode 100644 board/itead/sonoff-ihost/MAINTAINERS create mode 100644 configs/sonoff-ihost-rv1126_defconfig create mode 100644 include/configs/sonoff-ihost.h
arch/arm/dts/rv1126-sonoff-ihost-u-boot.dtsi new file +13 -0
@@ -0,0 +1,13 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) + +#include "rv1126-u-boot.dtsi" + +/ { + chosen { + u-boot,spl-boot-order = "same-as-spl", &sdmmc, &emmc; + }; +}; + +&sdio { + status = "disabled"; +};
arch/arm/mach-rockchip/rv1126/Kconfig +8 -0
@@ -14,6 +14,13 @@ config TARGET_RV1126_NEU2 IO board and Neu2 needs to mount on top of this IO board in order to create complete Edgeble Neural Compute Module 2(Neu2) IO platform. +config TARGET_RV1126_SONOFF_IHOST + bool "Sonoff iHost smart home hub" + help + Sonoff iHost is a smart home gateway based on Rockchip RV1126 SoC. + It features Wifi, Bluetooth and Zigbee radios that are used by many + smart home devices. + config SOC_SPECIFIC_OPTIONS # dummy def_bool y select HAS_CUSTOM_SYS_INIT_SP_ADDR
@@ -58,5 +65,6 @@ config TEXT_BASE default 0x600000 source board/edgeble/neural-compute-module-2/Kconfig +source board/itead/sonoff-ihost/Kconfig endif
board/itead/sonoff-ihost/Kconfig new file +16 -0
@@ -0,0 +1,16 @@ +if TARGET_RV1126_SONOFF_IHOST + +config SYS_BOARD + default "sonoff-ihost" + +config SYS_VENDOR + default "itead" + +config SYS_CONFIG_NAME + default "sonoff-ihost" + +config BOARD_SPECIFIC_OPTIONS # dummy + def_bool y + select RAM_ROCKCHIP_DDR4 + +endif
board/itead/sonoff-ihost/MAINTAINERS new file +6 -0
@@ -0,0 +1,6 @@ +RV1126-SONOFF-IHOST +M: Tim Lunn <[email protected]> +S: Maintained +F: board/itead/sonoff-ihost +F: include/configs/sonoff-ihost.h +F: configs/sonoff-ihost-rv1126_defconfig
configs/sonoff-ihost-rv1126_defconfig new file +60 -0
60 lines not on this page · raw message
doc/board/rockchip/rockchip.rst +1 -0
@@ -129,6 +129,7 @@ List of mainline supported Rockchip boards: * rv1126 - Edgeble Neural Compute Module 2 SoM - Neu2/Neu2k (neu2-io-r1126) + - Itead Sonoff iHost (sonoff-ihost-rv1126) Building --------
include/configs/sonoff-ihost.h new file +10 -0
@@ -0,0 +1,10 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ + +#ifndef __SONOFF_IHOST_H +#define __SONOFF_IHOST_H + +#define ROCKCHIP_DEVICE_SETTINGS + +#include <configs/rv1126_common.h> + +#endif /* __SONOFF_IHOST_H */
Signature · 1 line
2.40.1
Re: [PATCH v2 4/6] board: rockchip: Add Sonoff iHost board
Quoted 17 lines · Tim Lunn
Sonoff iHost is gateway device designed to provide a Smart Home Hub, it is based on Rockchip RV1126. There is also a version with 2GB RAM based off the RV1109 dual core SoC however this works with the same config as the RV1126 for uboot purposes.
Features:
- Rockchip RV1126
- 4GB DDR4
- 8GB eMMC
- microSD slot
- RMII Ethernet PHY
- 1x USB 2.0 Host
- 1x USB 2.0 OTG
- Realtek RTL8723DS WiFi/BT
- EFR32MG21 Silabs Zigbee radio
- Speaker/Microphone
Quoted 1 line
Signed-off-by Tim Lunn <[email protected]>
Thanks,
- Kever
Quoted 192 lines
---
Changes in v2:
- Remove board config not required with standard bootarch/arm/dts/rv1126-sonoff-ihost-u-boot.dtsi | 13 +++++ arch/arm/mach-rockchip/rv1126/Kconfig | 8 +++ board/itead/sonoff-ihost/Kconfig | 16 ++++++ board/itead/sonoff-ihost/MAINTAINERS | 6 ++ configs/sonoff-ihost-rv1126_defconfig | 60 ++++++++++++++++++++ doc/board/rockchip/rockchip.rst | 1 + include/configs/sonoff-ihost.h | 10 ++++ 7 files changed, 114 insertions(+)create mode 100644
arch/arm/dts/rv1126-sonoff-ihost-u-boot.dtsicreate mode 100644 board/itead/sonoff-ihost/Kconfig create mode 100644 board/itead/sonoff-ihost/MAINTAINERS create mode 100644 configs/sonoff-ihost-rv1126_defconfig create mode 100644include/configs/sonoff-ihost.harch/arm/dts/rv1126-sonoff-ihost-u-boot.dtsi new file +13
-0@@ -0,0 +1,13 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) + +#include "rv1126-u-boot.dtsi" + +/ { + chosen { + u-boot,spl-boot-order = "same-as-spl", &sdmmc, &emmc; + }; +}; + +&sdio { + status = "disabled"; +};arch/arm/mach-rockchip/rv1126/Kconfig +8
-0@@ -14,6 +14,13 @@ config TARGET_RV1126_NEU2 IO board and Neu2 needs to mount on top of this IO board in order to create complete Edgeble Neural Compute Module 2(Neu2) IO platform. +config TARGET_RV1126_SONOFF_IHOST + bool "Sonoff iHost smart home hub" + help + Sonoff iHost is a smart home gateway based on Rockchip RV1126 SoC. + It features Wifi, Bluetooth and Zigbee radios that are used by many + smart home devices. + config SOC_SPECIFIC_OPTIONS # dummy def_bool y select HAS_CUSTOM_SYS_INIT_SP_ADDR@@ -58,5 +65,6 @@ config TEXT_BASE default 0x600000 source board/edgeble/neural-compute-module-2/Kconfig +source board/itead/sonoff-ihost/Kconfig endifboard/itead/sonoff-ihost/Kconfig new file +16
-0@@ -0,0 +1,16 @@ +if TARGET_RV1126_SONOFF_IHOST + +config SYS_BOARD + default "sonoff-ihost" + +config SYS_VENDOR + default "itead" + +config SYS_CONFIG_NAME + default "sonoff-ihost" + +config BOARD_SPECIFIC_OPTIONS # dummy + def_bool y + select RAM_ROCKCHIP_DDR4 + +endifboard/itead/sonoff-ihost/MAINTAINERS new file +6
-0@@ -0,0 +1,6 @@ +RV1126-SONOFF-IHOST +M: Tim Lunn <[email protected]> +S: Maintained +F: board/itead/sonoff-ihost +F: include/configs/sonoff-ihost.h +F: configs/sonoff-ihost-rv1126_defconfigconfigs/sonoff-ihost-rv1126_defconfig new file +60
-0@@ -0,0 +1,60 @@ +CONFIG_ARM=y +CONFIG_SPL_SKIP_LOWLEVEL_INIT_ONLY=y +CONFIG_TPL_SKIP_LOWLEVEL_INIT_ONLY=y +CONFIG_COUNTER_FREQUENCY=24000000 +CONFIG_SYS_ARCH_TIMER=y +CONFIG_ARCH_ROCKCHIP=y +CONFIG_NR_DRAM_BANKS=1 +CONFIG_DEFAULT_DEVICE_TREE="rv1126-sonoff-ihost" +CONFIG_SYS_MONITOR_LEN=614400 +CONFIG_ROCKCHIP_RV1126=y +CONFIG_TARGET_RV1126_SONOFF_IHOST=y +CONFIG_DEBUG_UART_BASE=0xff570000 +CONFIG_DEBUG_UART_CLOCK=24000000 +CONFIG_SYS_LOAD_ADDR=0xe00800 +CONFIG_DEBUG_UART=y +CONFIG_FIT_VERBOSE=y +CONFIG_NR_DRAM_BANKS=2 +CONFIG_SPL_FIT=y +CONFIG_SPL_LOAD_FIT=y +# CONFIG_USE_SPL_FIT_GENERATOR is not set +CONFIG_SYS_BOOTM_LEN=0x4000000 +CONFIG_DEFAULT_FDT_FILE="rv1126-sonoff-ihost.dtb" +# CONFIG_DISPLAY_CPUINFO is not set +CONFIG_DISPLAY_BOARDINFO_LATE=y +CONFIG_SPL_PAD_TO=0x7f8000 +CONFIG_SPL_NO_BSS_LIMIT=y +# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set +# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set +# CONFIG_CMD_BOOTD is not set +# CONFIG_CMD_ELF is not set +# CONFIG_CMD_IMI is not set +# CONFIG_CMD_XIMG is not set +CONFIG_CMD_GPT=y +# CONFIG_CMD_LOADB is not set +# CONFIG_CMD_LOADS is not set +CONFIG_CMD_MMC=y +# CONFIG_CMD_ITEST is not set +# CONFIG_CMD_SETEXPR is not set +# CONFIG_SPL_DOS_PARTITION is not set +# CONFIG_ISO_PARTITION is not set +CONFIG_EFI_PARTITION_ENTRIES_NUMBERS=64 +CONFIG_OF_SPL_REMOVE_PROPS="clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents" +CONFIG_ENV_IS_IN_MMC=y +CONFIG_SYS_RELOC_GD_ENV_ADDR=y +CONFIG_ROCKCHIP_GPIO=y +CONFIG_SYS_I2C_ROCKCHIP=y +CONFIG_MISC=y +CONFIG_MMC_DW=y +CONFIG_MMC_DW_ROCKCHIP=y +CONFIG_REGULATOR_PWM=y +CONFIG_PWM_ROCKCHIP=y +# CONFIG_RAM_ROCKCHIP_DEBUG is not set +CONFIG_BAUDRATE=1500000 +CONFIG_DEBUG_UART_SHIFT=2 +CONFIG_SYSRESET=y +# CONFIG_TPL_SYSRESET is not set +CONFIG_DM_THERMAL=y +CONFIG_SPL_TINY_MEMSET=y +CONFIG_LZO=y +CONFIG_ERRNO_STR=ydoc/board/rockchip/rockchip.rst +1
-0@@ -129,6 +129,7 @@ List of mainline supported Rockchip boards: * rv1126 - Edgeble Neural Compute Module 2 SoM - Neu2/Neu2k (neu2-io-r1126) + - Itead Sonoff iHost (sonoff-ihost-rv1126) Building --------include/configs/sonoff-ihost.h new file +10
-0@@ -0,0 +1,10 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ + +#ifndef __SONOFF_IHOST_H +#define __SONOFF_IHOST_H + +#define ROCKCHIP_DEVICE_SETTINGS + +#include <configs/rv1126_common.h> + +#endif /* __SONOFF_IHOST_H */
PATCH v2 5/6 rockchip: rv1126: select SPL_OPTEE_IMAGE
In reply to Tim Lunnrv1126 requires OPTEE as it provides pcsi support. Mainline Linux kernel will fail to boot without this.
Select SPL_OPTEE_IMAGE when building FIT image. TEE must be provided when building.
---
(no changes since v1)
arch/arm/mach-rockchip/Kconfig | 1 + 1 file changed, 1 insertion(+)
arch/arm/mach-rockchip/Kconfig +1 -0
@@ -359,6 +359,7 @@ config ROCKCHIP_RV1126 select PMIC_RK8XX select BOARD_LATE_INIT imply ROCKCHIP_COMMON_BOARD + select SPL_OPTEE_IMAGE if SPL_FIT imply OF_LIBFDT_OVERLAY imply ROCKCHIP_OTP imply MISC_INIT_R
Signature · 1 line
2.40.1
Re: [PATCH v2 5/6] rockchip: rv1126: select SPL_OPTEE_IMAGE
Quoted 7 lines · Tim Lunn
rv1126 requires OPTEE as it provides pcsi support. Mainline Linux kernel will fail to boot without this.
Select
SPL_OPTEE_IMAGEwhen building FIT image. TEE must be provided when building.Signed-off-by Tim Lunn <[email protected]>
Thanks,
- Kever
Quoted 19 lines
---
(no changes since v1)
arch/arm/mach-rockchip/Kconfig | 1 + 1 file changed, 1 insertion(+)arch/arm/mach-rockchip/Kconfig +1
-0@@ -359,6 +359,7 @@ config ROCKCHIP_RV1126 select PMIC_RK8XX select BOARD_LATE_INIT imply ROCKCHIP_COMMON_BOARD + select SPL_OPTEE_IMAGE if SPL_FIT imply OF_LIBFDT_OVERLAY imply ROCKCHIP_OTP imply MISC_INIT_R
PATCH v2 6/6 rockchip: rv1126: Move RAM disk address
In reply to Tim LunnOPTEE gets loaded into a memory region overlapping with the ram disk.
Fix the ramdisk address so it doesn't overlap with the OPTEE memory region.
---
(no changes since v1)
include/configs/rv1126_common.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
include/configs/rv1126_common.h +1 -1
@@ -26,7 +26,7 @@"fdt_addr_r=0x08300000\0" \"fdtoverlay_addr_r=0x02000000\0" \"kernel_addr_r=0x02008000\0" \ -"ramdisk_addr_r=0x0a200000\0" +"ramdisk_addr_r=0x0a400000\0" #define CFG_EXTRA_ENV_SETTINGS \"fdt_high=0x0fffffff\0" \
Signature · 1 line
2.40.1
Re: [PATCH v2 6/6] rockchip: rv1126: Move RAM disk address
Quoted 6 lines · Tim Lunn
OPTEE gets loaded into a memory region overlapping with the ram disk.
Fix the ramdisk address so it doesn't overlap with the OPTEE memory region.
Signed-off-by Tim Lunn <[email protected]>
Thanks,
- Kever
Quoted 21 lines
---
(no changes since v1)
include/configs/rv1126_common.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)include/configs/rv1126_common.h +1
-1@@ -26,7 +26,7 @@"fdt_addr_r=0x08300000\0" \"fdtoverlay_addr_r=0x02000000\0" \"kernel_addr_r=0x02008000\0" \ -"ramdisk_addr_r=0x0a200000\0" +"ramdisk_addr_r=0x0a400000\0" #define CFG_EXTRA_ENV_SETTINGS \"fdt_high=0x0fffffff\0" \