Introduce ICSSG Ethernet driver
Subsystems (6)
v3 cover Introduce ICSSG Ethernet driver
Introduce ICSSG PRUETH support in uboot. The ICSSG driver is used in TI AM654 SR2.0.
The ICSSG PRU Sub-system runs on EMAC firmware. This series Introduces support for ICSSG driver in uboot. This series also adds the driver's dependencies.
The ICSSG2 node is added in device tree overlay so that it remains in sync with linux kernel.
The series introduces device tree and config changes and AM65x to enable ICSSG driver. The series also enables SPL_LOAD_FIT_APPLY_OVERLAY for AM65x in order to load overlay over spl.
This series has been tested on AM65x SR2.0, and the ICSSG interface is able to ping / dhcp and boot kernel using tftp in uboot.
To use ICSSG2 ethernet, the ICSSG firmware needs to be loaded to PRU RPROC cores and RPROC cores need to be booted with the firmware. This step is done inside driver similar to kernel.
The remoteproc driver uses request_fw_into_buf() API from fs-loader driver to load and start rproc with the required firmwares.
The users need to set env variables fw_storage_interface, fw_dev_part, fw_ubi_mtdpart, fw_ubi_volume to indicate which storage medium and partition they want to use to load firmware files from. By default the env fw_storage_interface=mmc and fw_dev_part=1:2 but users can modify these envs as per their requirements.
Log while running dhcp at u-boot:
k3-navss-ringacc ringacc@3c000000: Ring Accelerator probed rings:818, gp-rings[304,100] sci-dev-id:187 k3-navss-ringacc ringacc@3c000000: dma-ring-reset-quirk: disabled
prueth icssg2-eth: K3 ICSSG: rflow_id_base: 8, chn_name = rx0
link up on port 0, speed 1000, full duplex
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
DHCP client bound to address 192.168.4.97 (1037 ms)
This is v3 of the series [1].
Changes from v2 [2] to v3:
*) No functional changes.
*) Rebased the series on latest u-boot/next.
*) Dropped the RFC tag.
Changes from v1 to v2:
*) Modified the driver to load the firmware inside the driver only instead
of loading the firmware using commands at u-boot prompt. Added patch 3/16 for this.
*) Rebased the series on the latest u-boot/next.
*) Modified conf-0 configuration in k3-am65x-binman.dtsi as suggested by
Roger.
*) Dropped patch [3] as the patch is no longer needed.
*) Added patch 2/15 to modify fs-loader driver to use fw_storage_interface
env instead of storage_interface and keep the env storage_interface as fallback as suggested by Roger.
*) Added patch 15/15 to set default values to env fw_storage_interface and
fw_dev_part.
[1] https://lore.kernel.org/all/[email protected]/
[2] https://lore.kernel.org/all/[email protected]/
[3] https://lore.kernel.org/all/[email protected]/
NOTE: All the device tree changes introduced in this patch are already part of upstream linux kernel.
Thanks and Regards,
MD Danish Anwar
MD Danish Anwar (15):
dma: ti: k3-udma: Use ring_idx to pair k3 nav rings
misc: fs-loader: Use fw_storage_interface instead of storage_interface
remoteproc: uclass: Add methods to load firmware to rproc and boot
rproc
net: ti: icssg: Add Firmware Interface for ICSSG Ethernet driver.
net: ti: icssg: Add Firmware config and classification APIs.
net: ti: icssg: Add icssg queues APIs and macros
net: ti: icssg: Add ICSSG ethernet driver
net: ti: icssg: Add support sending FDB command to update rx_flow_id
net: ti: icssg: Enforce pinctrl state on the MDIO child node
arm: dts: k3-am654-base-board: Add ICSSG2 Ethernet support
arm: dts: k3-am65x-binman: Add ICSSG2 overlay and configuration
configs: am65x_evm_a53: Enable ICSSG Driver
configs: am65x_evm_a53: add SPL_LOAD_FIT_APPLY_OVERLAY
board: ti: am65x: Add check for k3-am654-icssg2 in
board_fit_config_match()
board: ti: am65x: Set fw_storage_interface and fw_dev_part ENVs
arch/arm/dts/Makefile | 3 +- arch/arm/dts/k3-am654-icssg2.dtso | 145 ++++ arch/arm/dts/k3-am65x-binman.dtsi | 65 +- board/ti/am65x/am65x.env | 4 + board/ti/am65x/evm.c | 11 +- configs/am65x_evm_a53_defconfig | 2 + .../driver-model/fs_firmware_loader.rst | 5 +- drivers/dma/ti/k3-udma.c | 11 +- drivers/misc/fs_loader.c | 5 +- drivers/net/ti/Kconfig | 9 + drivers/net/ti/Makefile | 1 + drivers/net/ti/icss_mii_rt.h | 192 +++++ drivers/net/ti/icssg_classifier.c | 376 +++++++++ drivers/net/ti/icssg_config.c | 463 +++++++++++ drivers/net/ti/icssg_config.h | 195 +++++ drivers/net/ti/icssg_prueth.c | 762 ++++++++++++++++++ drivers/net/ti/icssg_prueth.h | 92 +++ drivers/net/ti/icssg_queues.c | 51 ++ drivers/net/ti/icssg_switch_map.h | 209 +++++ drivers/remoteproc/Kconfig | 1 + drivers/remoteproc/rproc-uclass.c | 85 ++ include/remoteproc.h | 35 + 22 files changed, 2709 insertions(+), 13 deletions(-) create mode 100644 arch/arm/dts/k3-am654-icssg2.dtso create mode 100644 drivers/net/ti/icss_mii_rt.h create mode 100644 drivers/net/ti/icssg_classifier.c create mode 100644 drivers/net/ti/icssg_config.c create mode 100644 drivers/net/ti/icssg_config.h create mode 100644 drivers/net/ti/icssg_prueth.c create mode 100644 drivers/net/ti/icssg_prueth.h create mode 100644 drivers/net/ti/icssg_queues.c create mode 100644 drivers/net/ti/icssg_switch_map.h
base-commit: f28a77589e7505535a4eebdc7269df98f67dbe68
Signature · 1 line
2.34.1
RFC PATCH v3 1/15 dma: ti: k3-udma: Use ring_idx to pair k3 nav rings
Use ring_idx to pair rings. ring_idx will be same as tx flow_id for all non-negative flow_ids. For negative flow_ids, ring_idx will be tchan->id added with bchan_cnt.
--- drivers/dma/ti/k3-udma.c | 11 +++++++++-- 1 file changed, 9 insertions(+), 2 deletions(-)
drivers/dma/ti/k3-udma.c +9 -2
@@ -876,13 +876,20 @@ static int udma_alloc_tx_resources(struct udma_chan *uc) {struct k3_nav_ring_cfg ring_cfg;struct udma_dev *ud = uc->ud; -int ret; +struct udma_tchan *tchan; +int ring_idx, ret; ret =udma_get_tchan (uc);if (ret)return ret; - ret =k3_nav_ringacc_request_rings_pair (ud->ringacc, uc->tchan->id,-1 , + tchan = uc->tchan; +if (tchan->tflow_id >=0 ) + ring_idx = tchan->tflow_id; +else + ring_idx = ud->bchan_cnt + tchan->id; + + ret =k3_nav_ringacc_request_rings_pair (ud->ringacc, ring_idx,-1 , &uc->tchan->t_ring, &uc->tchan->tc_ring);if (ret) {
Signature · 1 line
2.34.1
RFC PATCH v3 2/15 misc: fs-loader: Use fw_storage_interface instead of storage_interface
In reply to MD Danish AnwarThe fs-loader driver reads env storage_interface and uses it to load firmware file into memory using the medium set by env. Update the driver to use env fw_storage_interface as this variable is only used to load firmwares. The env storage_interface will act as fallback so that the existing implementations do not break.
Also update the FS Loader documentation accordingly.
--- doc/develop/driver-model/fs_firmware_loader.rst | 5 ++++- drivers/misc/fs_loader.c | 5 ++++- 2 files changed, 8 insertions(+), 2 deletions(-)
doc/develop/driver-model/fs_firmware_loader.rst +4 -1
@@ -98,8 +98,11 @@ through the U-Boot environment variable during run time. For examples: +fw_storage_interface: + Firmware storage interface, it can be "mmc", "usb", "sata" or "ubi". storage_interface: - Storage interface, it can be "mmc", "usb", "sata" or "ubi". + Storage interface, it can be "mmc", "usb", "sata" or "ubi". This acts + as a fallback if fw_storage_interface is not set. fw_dev_part: Block device number and its partition, it can be "0:1". fw_ubi_mtdpart:
drivers/misc/fs_loader.c +4 -1
@@ -153,7 +153,10 @@ static int fw_get_filesystem_firmware(struct udevice *dev)char *storage_interface, *dev_part, *ubi_mtdpart, *ubi_volume;int ret; - storage_interface =env_get ("storage_interface" ); + storage_interface =env_get ("fw_storage_interface" ); +if (!storage_interface) + storage_interface =env_get ("storage_interface" ); + dev_part =env_get ("fw_dev_part" ); ubi_mtdpart =env_get ("fw_ubi_mtdpart" ); ubi_volume =env_get ("fw_ubi_volume" );
Signature · 1 line
2.34.1
Re: [RFC PATCH v3 02/15] misc: fs-loader: Use fw_storage_interface instead of storage_interface
Quoted 50 lines · MD Danish Anwar
The fs-loader driver reads env
storage_interfaceand uses it to load firmware file into memory using the medium set by env. Update the driver to use envfw_storage_interfaceas this variable is only used to load firmwares. The envstorage_interfacewill act as fallback so that the existing implementations do not break.Also update the FS Loader documentation accordingly.
Signed-off-by MD Danish Anwar <[email protected]>--- doc/develop/driver-model/fs_firmware_loader.rst | 5 ++++- drivers/misc/fs_loader.c | 5 ++++- 2 files changed, 8 insertions(+), 2 deletions(-)doc/develop/driver-model/fs_firmware_loader.rst +4
-1@@ -98,8 +98,11 @@ through the U-Boot environment variable during run time. For examples: +fw_storage_interface: + Firmware storage interface, it can be "mmc", "usb", "sata" or "ubi". storage_interface: - Storage interface, it can be "mmc", "usb", "sata" or "ubi". + Storage interface, it can be "mmc", "usb", "sata" or "ubi". This acts + as a fallback if fw_storage_interface is not set. fw_dev_part: Block device number and its partition, it can be "0:1". fw_ubi_mtdpart:drivers/misc/fs_loader.c +4
-1@@ -153,7 +153,10 @@ static int fw_get_filesystem_firmware(struct udevice *dev)char *storage_interface, *dev_part, *ubi_mtdpart, *ubi_volume;int ret; - storage_interface =env_get ("storage_interface" ); + storage_interface =env_get ("fw_storage_interface" ); +if (!storage_interface) + storage_interface =env_get ("storage_interface" ); + dev_part =env_get ("fw_dev_part" ); ubi_mtdpart =env_get ("fw_ubi_mtdpart" ); ubi_volume =env_get ("fw_ubi_volume" );Signature · 1 line
2.34.1
You should move these specific patches out of the series and debate on their merits seperately. mixing things like these in a single series that needs to go to multiple u-boot custodians just creates problems for everyone.
Signature · 3 lines
Regards, Nishanth Menon Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
Re: [RFC PATCH v3 02/15] misc: fs-loader: Use fw_storage_interface instead of storage_interface
Hi Nishant,
Quoted 40 lines · Nishanth Menon
Quoted 39 lines · MD Danish Anwar
The fs-loader driver reads env
storage_interfaceand uses it to load firmware file into memory using the medium set by env. Update the driver to use envfw_storage_interfaceas this variable is only used to load firmwares. The envstorage_interfacewill act as fallback so that the existing implementations do not break.Also update the FS Loader documentation accordingly.
Signed-off-by MD Danish Anwar <[email protected]>--- doc/develop/driver-model/fs_firmware_loader.rst | 5 ++++- drivers/misc/fs_loader.c | 5 ++++- 2 files changed, 8 insertions(+), 2 deletions(-)doc/develop/driver-model/fs_firmware_loader.rst +4
-1@@ -98,8 +98,11 @@ through the U-Boot environment variable during run time. For examples: +fw_storage_interface: + Firmware storage interface, it can be "mmc", "usb", "sata" or "ubi". storage_interface: - Storage interface, it can be "mmc", "usb", "sata" or "ubi". + Storage interface, it can be "mmc", "usb", "sata" or "ubi". This acts + as a fallback if fw_storage_interface is not set. fw_dev_part: Block device number and its partition, it can be "0:1". fw_ubi_mtdpart:drivers/misc/fs_loader.c +0
-0@@ -153,7 +153,10 @@ static int fw_get_filesystem_firmware(struct udevice *dev)char *storage_interface, *dev_part, *ubi_mtdpart, *ubi_volume;int ret;
Quoted 17 lines
Quoted 11 lines
drivers/misc/fs_loader.c +4
-1- storage_interface =env_get ("storage_interface" ); + storage_interface =env_get ("fw_storage_interface" ); +if (!storage_interface) + storage_interface =env_get ("storage_interface" ); + dev_part =env_get ("fw_dev_part" ); ubi_mtdpart =env_get ("fw_ubi_mtdpart" ); ubi_volume =env_get ("fw_ubi_volume" );Signature · 1 line
2.34.1You should move these specific patches out of the series and debate on their merits seperately. mixing things like these in a single series that needs to go to multiple u-boot custodians just creates problems for everyone.
I have kept these patches in the series because ICSSG driver depends on these patches. I didn't want to post multiple series and map dependencies so I posted all patches in one series. Patch 1 to 3 are dependency for ICSSG driver. Patch 4 to 9 are ICSSG driver patches. Patch 10 to 15 are AM65x-EVM specific patches (DTS and configs).
The first 3 patches will also go to different u-boot custodians as first one is dma related, second one is related to fs-loader driver and the third one modifies the remoteproc driver. So instead of posting all these separately, I wanted to post it along with the ICSSG driver series so that folks can understand why these three patches are needed.
Signature · 2 lines
Thanks and Regards, Md Danish Anwar
RFC PATCH v3 3/15 remoteproc: uclass: Add methods to load firmware to rproc and boot rproc
In reply to MD Danish AnwarAdd APIs to set a firmware_name to a rproc and boot the rproc with the same firmware.
Clients can call rproc_set_firmware() API to set firmware_name for a rproc whereas rproc_boot() will load the firmware set by rproc_set_firmware() to a buffer by calling request_firmware_into_buf(). rproc_boot() will then load the firmware file to the remote processor and start the remote processor.
Also include "fs-loader.h" and make remoteproc driver select FS_LOADER in Kconfig so that we can call request_firmware_into_buf() from remoteproc driver.
--- drivers/remoteproc/Kconfig | 1 + drivers/remoteproc/rproc-uclass.c | 85 +++++++++++++++++++++++++++++++ include/remoteproc.h | 35 +++++++++++++ 3 files changed, 121 insertions(+)
drivers/remoteproc/Kconfig +1 -0
@@ -10,6 +10,7 @@ menu "Remote Processor drivers" # All users should depend on DM config REMOTEPROC bool + select FS_LOADER depends on DM # Please keep the configuration alphabetically sorted.
drivers/remoteproc/rproc-uclass.c +85 -0
94 lines not on this page · raw message
include/remoteproc.h +35 -0
@@ -402,6 +402,7 @@ enum rproc_mem_type {* @name: Platform-specific way of naming the Remote proc * @mem_type: one of 'enum rproc_mem_type' * @driver_plat_data: driver specific platform data that may be needed. +* @fw_name: firmware name * * This can be accessed with dev_get_uclass_plat() for any UCLASS_REMOTEPROC * device.
@@ -411,6 +412,7 @@ struct dm_rproc_uclass_pdata {const char *name;enum rproc_mem_type mem_type;void *driver_plat_data; +char *fw_name; };/**
@@ -704,6 +706,35 @@ unsigned long rproc_parse_resource_table(struct udevice *dev,struct resource_table *rproc_find_resource_table (struct udevice *dev,unsigned int addr,int *tablesz); +/** +* rproc_set_firmware() - assign a new firmware +* @rproc_dev: device for wich new firmware is being assigned +* @fw_name: new firmware name to be assigned +* +* This function allows remoteproc drivers or clients to configure a custom +* firmware name. The function does not trigger a remote processor boot, +* only sets the firmware name used for a subsequent boot. +* +* This function sets the fw_name field in uclass pdata of the Remote proc +* +* Return: 0 on success or a negative value upon failure +*/ +int rproc_set_firmware (struct udevice *rproc_dev,const char *fw_name); + +/** +* rproc_boot() - boot a remote processor +* @rproc_dev: rproc device to boot +* @fw_size: Size of the memory to allocate for firmeware +* +* Boot a remote processor (i.e. load its firmware, power it on, ...). +* +* This function first loads the firmware set in the uclass pdata of Remote +* processor to a buffer and then loads firmware to the remote processor +* using rproc_load(). +* +* Return: 0 on success, and an appropriate error value otherwise +*/ +int rproc_boot (struct udevice *rproc_dev,size_t fw_size);#else static inline int rproc_init (void ) {return -ENOSYS ; }static inline int rproc_dev_init (int id) {return -ENOSYS ; }
@@ -743,6 +774,10 @@ static inline int rproc_elf_load_rsc_table(struct udevice *dev, ulong fw_addr, ulong fw_size, ulong *rsc_addr, ulong *rsc_size) { return -ENOSYS; } +static inline int rproc_set_firmware (struct udevice *rproc_dev,const char *fw_name) +{return -ENOSYS ; } +static inline int rproc_boot (struct udevice *rproc_dev,size_t fw_size) +{return -ENOSYS ; }#endif #endif /* _RPROC_H_ */
Signature · 1 line
2.34.1
RFC PATCH v3 4/15 net: ti: icssg: Add Firmware Interface for ICSSG Ethernet driver.
In reply to MD Danish AnwarAdd firmware interface related headers and macros for ICSSG Ethernet driver. These macros will be later used by the ICSSG ethernet driver.
--- drivers/net/ti/icssg_switch_map.h | 209 ++++++++++++++++++++++++++++++ 1 file changed, 209 insertions(+) create mode 100644 drivers/net/ti/icssg_switch_map.h
drivers/net/ti/icssg_switch_map.h new file +209 -0
@@ -0,0 +1,209 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* Texas Instruments ICSSG Ethernet driver +* +* Copyright (C) 2020 Texas Instruments Incorporated - https://www.ti.com/ +* +*/ + +#ifndef __NET_TI_ICSSG_SWITCH_MAP_H +#define __NET_TI_ICSSG_SWITCH_MAP_H + +/*Time after which FDB entries are checked for aged out values. Value in nanoseconds*/ +#define FDB_AGEING_TIMEOUT_OFFSET 0x0014 + +/*default VLAN tag for Host Port*/ +#define HOST_PORT_DF_VLAN_OFFSET 0x001C + +/*Same as HOST_PORT_DF_VLAN_OFFSET*/ +#define EMAC_ICSSG_SWITCH_PORT0_DEFAULT_VLAN_OFFSET HOST_PORT_DF_VLAN_OFFSET + +/*default VLAN tag for P1 Port*/ +#define P1_PORT_DF_VLAN_OFFSET 0x0020 + +/*Same as P1_PORT_DF_VLAN_OFFSET*/ +#define EMAC_ICSSG_SWITCH_PORT1_DEFAULT_VLAN_OFFSET P1_PORT_DF_VLAN_OFFSET + +/*default VLAN tag for P2 Port*/ +#define P2_PORT_DF_VLAN_OFFSET 0x0024 + +/*Same as P2_PORT_DF_VLAN_OFFSET*/ +#define EMAC_ICSSG_SWITCH_PORT2_DEFAULT_VLAN_OFFSET P2_PORT_DF_VLAN_OFFSET + +/*VLAN-FID Table offset. 4096 VIDs. 2B per VID = 8KB = 0x2000*/ +#define VLAN_STATIC_REG_TABLE_OFFSET 0x0100 + +/*VLAN-FID Table offset for EMAC*/ +#define EMAC_ICSSG_SWITCH_DEFAULT_VLAN_TABLE_OFFSET VLAN_STATIC_REG_TABLE_OFFSET + +/*packet descriptor Q reserved memory*/ +#define PORT_DESC0_HI 0x2104 + +/*packet descriptor Q reserved memory*/ +#define PORT_DESC0_LO 0x2F6C + +/*packet descriptor Q reserved memory*/ +#define PORT_DESC1_HI 0x3DD4 + +/*packet descriptor Q reserved memory*/ +#define PORT_DESC1_LO 0x4C3C + +/*packet descriptor Q reserved memory*/ +#define HOST_DESC0_HI 0x5AA4 + +/*packet descriptor Q reserved memory*/ +#define HOST_DESC0_LO 0x5F0C + +/*packet descriptor Q reserved memory*/ +#define HOST_DESC1_HI 0x6374 + +/*packet descriptor Q reserved memory*/ +#define HOST_DESC1_LO 0x67DC + +/*special packet descriptor Q reserved memory*/ +#define HOST_SPPD0 0x7AAC + +/*special packet descriptor Q reserved memory*/ +#define HOST_SPPD1 0x7EAC + +/*_Small_Description_*/ +#define TIMESYNC_FW_WC_CYCLECOUNT_OFFSET 0x83EC + +/*IEP count hi roll over count*/ +#define TIMESYNC_FW_WC_HI_ROLLOVER_COUNT_OFFSET 0x83F4 + +/*_Small_Description_*/ +#define TIMESYNC_FW_WC_COUNT_HI_SW_OFFSET_OFFSET 0x83F8 + +/*Set clock descriptor*/ +#define TIMESYNC_FW_WC_SETCLOCK_DESC_OFFSET 0x83FC + +/*_Small_Description_*/ +#define TIMESYNC_FW_WC_SYNCOUT_REDUCTION_FACTOR_OFFSET 0x843C + +/*_Small_Description_*/ +#define TIMESYNC_FW_WC_SYNCOUT_REDUCTION_COUNT_OFFSET 0x8440 + +/*_Small_Description_*/ +#define TIMESYNC_FW_WC_SYNCOUT_START_TIME_CYCLECOUNT_OFFSET 0x8444 + +/*Control variable to generate SYNC1*/ +#define TIMESYNC_FW_WC_ISOM_PIN_SIGNAL_EN_OFFSET 0x844C + +/*SystemTime Sync0 periodicity*/ +#define TIMESYNC_FW_ST_SYNCOUT_PERIOD_OFFSET 0x8450 + +/*pktTxDelay for P1 = link speed dependent p1 mac delay + p1 phy delay*/ +#define TIMESYNC_FW_WC_PKTTXDELAY_P1_OFFSET 0x8454 + +/*pktTxDelay for P2 = link speed dependent p2 mac delay + p2 phy delay*/ +#define TIMESYNC_FW_WC_PKTTXDELAY_P2_OFFSET 0x8458 + +/*Set clock operation done signal for next task*/ +#define TIMESYNC_FW_SIG_PNFW_OFFSET 0x845C + +/*Set clock operation done signal for next task*/ +#define TIMESYNC_FW_SIG_TIMESYNCFW_OFFSET 0x8460 + +/*New list is copied at this time*/ +#define TAS_CONFIG_CHANGE_TIME 0x000C + +/*config change error counter*/ +#define TAS_CONFIG_CHANGE_ERROR_COUNTER 0x0014 + +/*TAS List update pending flag*/ +#define TAS_CONFIG_PENDING 0x0018 + +/*TAS list update trigger flag*/ +#define TAS_CONFIG_CHANGE 0x0019 + +/*List length for new TAS schedule*/ +#define TAS_ADMIN_LIST_LENGTH 0x001A + +/*Currently active TAS list index*/ +#define TAS_ACTIVE_LIST_INDEX 0x001B + +/*Cycle time for the new TAS schedule*/ +#define TAS_ADMIN_CYCLE_TIME 0x001C + +/*Cycle counts remaining till the TAS list update*/ +#define TAS_CONFIG_CHANGE_CYCLE_COUNT 0x0020 + +/*Base Flow ID for sending packets to Host for Slice0*/ +#define PSI_L_REGULAR_FLOW_ID_BASE_OFFSET 0x0024 + +/*Same as PSI_L_REGULAR_FLOW_ID_BASE_OFFSET*/ +#define EMAC_ICSSG_SWITCH_PSI_L_REGULAR_FLOW_ID_BASE_OFFSET PSI_L_REGULAR_FLOW_ID_BASE_OFFSET + +/*Base Flow ID for sending mgmt and Tx TS to Host for Slice0*/ +#define PSI_L_MGMT_FLOW_ID_OFFSET 0x0026 + +/*Same as PSI_L_MGMT_FLOW_ID_OFFSET*/ +#define EMAC_ICSSG_SWITCH_PSI_L_MGMT_FLOW_ID_BASE_OFFSET PSI_L_MGMT_FLOW_ID_OFFSET + +/*Queue number for Special packets written here*/ +#define SPL_PKT_DEFAULT_PRIORITY 0x0028 + +/*Express Preemptible Queue Mask*/ +#define EXPRESS_PRE_EMPTIVE_Q_MASK 0x0029 + +/*Port1/Port2 Default Queue number for untagged packets, only 1B is used*/ +#define QUEUE_NUM_UNTAGGED 0x002A + +/*Stores the table used for priority regeneration. 1B per PCP/Queue*/ +#define PORT_Q_PRIORITY_REGEN_OFFSET 0x002C + +/* For marking Packet as priority/express (this feature is disabled) or +* cut-through/S&F. +*/ +#define EXPRESS_PRE_EMPTIVE_Q_MAP 0x0034 + +/*Stores the table used for priority mapping. 1B per PCP/Queue*/ +#define PORT_Q_PRIORITY_MAPPING_OFFSET 0x003C + +/*TAS gate mask for windows list0*/ +#define TAS_GATE_MASK_LIST0 0x0100 + +/*TAS gate mask for windows list1*/ +#define TAS_GATE_MASK_LIST1 0x0350 + +/*Memory to Enable/Disable Preemption on TX side*/ +#define PRE_EMPTION_ENABLE_TX 0x05A0 + +/*Active State of Preemption on TX side*/ +#define PRE_EMPTION_ACTIVE_TX 0x05A1 + +/*Memory to Enable/Disable Verify State Machine Preemption*/ +#define PRE_EMPTION_ENABLE_VERIFY 0x05A2 + +/*Verify Status of State Machine*/ +#define PRE_EMPTION_VERIFY_STATUS 0x05A3 + +/*Non Final Fragment Size supported by Link Partner*/ +#define PRE_EMPTION_ADD_FRAG_SIZE_REMOTE 0x05A4 + +/*Non Final Fragment Size supported by Firmware*/ +#define PRE_EMPTION_ADD_FRAG_SIZE_LOCAL 0x05A6 + +/*Time in ms the State machine waits for respond packet*/ +#define PRE_EMPTION_VERIFY_TIME 0x05A8 + +/*Memory used for R30 related management commands*/ +#define MGR_R30_CMD_OFFSET 0x05AC + +/*HW Buffer Pool0 base address*/ +#define BUFFER_POOL_0_ADDR_OFFSET 0x05BC + +/*16B for Host Egress MSMC Q (Pre-emptible) context*/ +#define HOST_RX_Q_PRE_CONTEXT_OFFSET 0x0684 + +/*Buffer for 8 FDB entries to be added by 'Add Multiple FDB entries IOCTL*/ +#define FDB_CMD_BUFFER 0x0894 + +/*16B for Host Egress MSMC Q (Express) context*/ +#define HOST_RX_Q_EXP_CONTEXT_OFFSET 0x0940 + +/*Start of 32 bits PA_STAT counters*/ +#define PA_STAT_32b_START_OFFSET 0x0080 + +#endif +/* __NET_TI_ICSSG_SWITCH_MAP_H */
Signature · 1 line
2.34.1
RFC PATCH v3 5/15 net: ti: icssg: Add Firmware config and classification APIs.
In reply to MD Danish AnwarAdd icssg_config.h / .c and icssg_classifier.c files. These are firmware configuration and classification related files. Add MII helper APIs and MACROs. These APIs and MACROs will be later used by ICSSG Ethernet driver. Also introduce icssg_prueth.h which has definition of prueth related structures.
--- drivers/net/ti/icss_mii_rt.h | 192 +++++++++++++++ drivers/net/ti/icssg_classifier.c | 376 ++++++++++++++++++++++++++++ drivers/net/ti/icssg_config.c | 397 ++++++++++++++++++++++++++++++ drivers/net/ti/icssg_config.h | 177 +++++++++++++ drivers/net/ti/icssg_prueth.h | 78 ++++++ 5 files changed, 1220 insertions(+) create mode 100644 drivers/net/ti/icss_mii_rt.h create mode 100644 drivers/net/ti/icssg_classifier.c create mode 100644 drivers/net/ti/icssg_config.c create mode 100644 drivers/net/ti/icssg_config.h create mode 100644 drivers/net/ti/icssg_prueth.h
drivers/net/ti/icss_mii_rt.h new file +192 -0
@@ -0,0 +1,192 @@ +/* SPDX-License-Identifier: GPL-2.0 */ + +/* PRU-ICSS MII_RT register definitions +* +* Copyright (C) 2015-2020 Texas Instruments Incorporated - http://www.ti.com +*/ + +#ifndef __NET_PRUSS_MII_RT_H__ +#define __NET_PRUSS_MII_RT_H__ + +#include <regmap.h> + +/* PRUSS_MII_RT Registers */ +#define PRUSS_MII_RT_RXCFG0 0x0 +#define PRUSS_MII_RT_RXCFG1 0x4 +#define PRUSS_MII_RT_TXCFG0 0x10 +#define PRUSS_MII_RT_TXCFG1 0x14 +#define PRUSS_MII_RT_TX_CRC0 0x20 +#define PRUSS_MII_RT_TX_CRC1 0x24 +#define PRUSS_MII_RT_TX_IPG0 0x30 +#define PRUSS_MII_RT_TX_IPG1 0x34 +#define PRUSS_MII_RT_PRS0 0x38 +#define PRUSS_MII_RT_PRS1 0x3c +#define PRUSS_MII_RT_RX_FRMS0 0x40 +#define PRUSS_MII_RT_RX_FRMS1 0x44 +#define PRUSS_MII_RT_RX_PCNT0 0x48 +#define PRUSS_MII_RT_RX_PCNT1 0x4c +#define PRUSS_MII_RT_RX_ERR0 0x50 +#define PRUSS_MII_RT_RX_ERR1 0x54 + +/* PRUSS_MII_RT_RXCFG0/1 bits */ +#define PRUSS_MII_RT_RXCFG_RX_ENABLE BIT(0) +#define PRUSS_MII_RT_RXCFG_RX_DATA_RDY_MODE_DIS BIT(1) +#define PRUSS_MII_RT_RXCFG_RX_CUT_PREAMBLE BIT(2) +#define PRUSS_MII_RT_RXCFG_RX_MUX_SEL BIT(3) +#define PRUSS_MII_RT_RXCFG_RX_L2_EN BIT(4) +#define PRUSS_MII_RT_RXCFG_RX_BYTE_SWAP BIT(5) +#define PRUSS_MII_RT_RXCFG_RX_AUTO_FWD_PRE BIT(6) +#define PRUSS_MII_RT_RXCFG_RX_L2_EOF_SCLR_DIS BIT(9) + +/* PRUSS_MII_RT_TXCFG0/1 bits */ +#define PRUSS_MII_RT_TXCFG_TX_ENABLE BIT(0) +#define PRUSS_MII_RT_TXCFG_TX_AUTO_PREAMBLE BIT(1) +#define PRUSS_MII_RT_TXCFG_TX_EN_MODE BIT(2) +#define PRUSS_MII_RT_TXCFG_TX_BYTE_SWAP BIT(3) +#define PRUSS_MII_RT_TXCFG_TX_MUX_SEL BIT(8) +#define PRUSS_MII_RT_TXCFG_PRE_TX_AUTO_SEQUENCE BIT(9) +#define PRUSS_MII_RT_TXCFG_PRE_TX_AUTO_ESC_ERR BIT(10) +#define PRUSS_MII_RT_TXCFG_TX_32_MODE_EN BIT(11) +#define PRUSS_MII_RT_TXCFG_TX_IPG_WIRE_CLK_EN BIT(12)/* SR2.0 onwards */ + +#define PRUSS_MII_RT_TXCFG_TX_START_DELAY_SHIFT 16 +#define PRUSS_MII_RT_TXCFG_TX_START_DELAY_MASK GENMASK(25, 16) + +#define PRUSS_MII_RT_TXCFG_TX_CLK_DELAY_SHIFT 28 +#define PRUSS_MII_RT_TXCFG_TX_CLK_DELAY_MASK GENMASK(30, 28) + +/* PRUSS_MII_RT_TX_IPG0/1 bits */ +#define PRUSS_MII_RT_TX_IPG_IPG_SHIFT 0 +#define PRUSS_MII_RT_TX_IPG_IPG_MASK GENMASK(9, 0) + +/* PRUSS_MII_RT_PRS0/1 bits */ +#define PRUSS_MII_RT_PRS_COL BIT(0) +#define PRUSS_MII_RT_PRS_CRS BIT(1) + +/* PRUSS_MII_RT_RX_FRMS0/1 bits */ +#define PRUSS_MII_RT_RX_FRMS_MIN_FRM_SHIFT 0 +#define PRUSS_MII_RT_RX_FRMS_MIN_FRM_MASK GENMASK(15, 0) + +#define PRUSS_MII_RT_RX_FRMS_MAX_FRM_SHIFT 16 +#define PRUSS_MII_RT_RX_FRMS_MAX_FRM_MASK GENMASK(31, 16) + +/* Min/Max in MII_RT_RX_FRMS */ +/* For EMAC and Switch */ +#define PRUSS_MII_RT_RX_FRMS_MAX (VLAN_ETH_FRAME_LEN + ETH_FCS_LEN) +#define PRUSS_MII_RT_RX_FRMS_MIN_FRM (64) + +/* for HSR and PRP */ +#define PRUSS_MII_RT_RX_FRMS_MAX_FRM_LRE (PRUSS_MII_RT_RX_FRMS_MAX + \ + ICSS_LRE_TAG_RCT_SIZE) +/* PRUSS_MII_RT_RX_PCNT0/1 bits */ +#define PRUSS_MII_RT_RX_PCNT_MIN_PCNT_SHIFT 0 +#define PRUSS_MII_RT_RX_PCNT_MIN_PCNT_MASK GENMASK(3, 0) + +#define PRUSS_MII_RT_RX_PCNT_MAX_PCNT_SHIFT 4 +#define PRUSS_MII_RT_RX_PCNT_MAX_PCNT_MASK GENMASK(7, 4) + +/* PRUSS_MII_RT_RX_ERR0/1 bits */ +#define PRUSS_MII_RT_RX_ERR_MIN_PCNT_ERR BIT(0) +#define PRUSS_MII_RT_RX_ERR_MAX_PCNT_ERR BIT(1) +#define PRUSS_MII_RT_RX_ERR_MIN_FRM_ERR BIT(2) +#define PRUSS_MII_RT_RX_ERR_MAX_FRM_ERR BIT(3) + +#define ICSSG_CFG_OFFSET 0 +#define RGMII_CFG_OFFSET 4 + +/* Constant to choose between MII0 and MII1 */ +#define ICSS_MII0 0 +#define ICSS_MII1 1 + +/* ICSSG_CFG Register bits */ +#define ICSSG_CFG_SGMII_MODE BIT(16) +#define ICSSG_CFG_TX_PRU_EN BIT(11) +#define ICSSG_CFG_RX_SFD_TX_SOF_EN BIT(10) +#define ICSSG_CFG_RTU_PRU_PSI_SHARE_EN BIT(9) +#define ICSSG_CFG_IEP1_TX_EN BIT(8) +#define ICSSG_CFG_MII1_MODE GENMASK(6, 5) +#define ICSSG_CFG_MII1_MODE_SHIFT 5 +#define ICSSG_CFG_MII0_MODE GENMASK(4, 3) +#define ICSSG_CFG_MII0_MODE_SHIFT 3 +#define ICSSG_CFG_RX_L2_G_EN BIT(2) +#define ICSSG_CFG_TX_L2_EN BIT(1) +#define ICSSG_CFG_TX_L1_EN BIT(0) + +enum mii_mode {MII_MODE_MII =0 ,MII_MODE_RGMII ,MII_MODE_SGMII }; + +/* RGMII CFG Register bits */ +#define RGMII_CFG_INBAND_EN_MII0 BIT(16) +#define RGMII_CFG_GIG_EN_MII0 BIT(17) +#define RGMII_CFG_INBAND_EN_MII1 BIT(20) +#define RGMII_CFG_GIG_EN_MII1 BIT(21) +#define RGMII_CFG_FULL_DUPLEX_MII0 BIT(18) +#define RGMII_CFG_FULL_DUPLEX_MII1 BIT(22) +#define RGMII_CFG_SPEED_MII0 GENMASK(2, 1) +#define RGMII_CFG_SPEED_MII1 GENMASK(6, 5) +#define RGMII_CFG_SPEED_MII0_SHIFT 1 +#define RGMII_CFG_SPEED_MII1_SHIFT 5 +#define RGMII_CFG_FULLDUPLEX_MII0 BIT(3) +#define RGMII_CFG_FULLDUPLEX_MII1 BIT(7) +#define RGMII_CFG_FULLDUPLEX_MII0_SHIFT 3 +#define RGMII_CFG_FULLDUPLEX_MII1_SHIFT 7 +#define RGMII_CFG_SPEED_10M 0 +#define RGMII_CFG_SPEED_100M 1 +#define RGMII_CFG_SPEED_1G 2 + +static inline void icssg_mii_update_ipg (struct regmap *mii_rt,int mii,u32 ipg) +{ +u32 val; + +if (mii ==ICSS_MII0 ) { +regmap_write (mii_rt,PRUSS_MII_RT_TX_IPG0 , ipg); + }else { +/* Errata workaround: IEP1 is not read by h/w unless IEP0 is written */ +regmap_read (mii_rt,PRUSS_MII_RT_TX_IPG0 , &val); +regmap_write (mii_rt,PRUSS_MII_RT_TX_IPG1 , ipg); +regmap_write (mii_rt,PRUSS_MII_RT_TX_IPG0 , val); + } +} + +static inline void icssg_update_rgmii_cfg (struct regmap *miig_rt,int speed, +bool full_duplex,int slice,struct prueth *priv) +{ +u32 gig_en_mask, gig_val =0 , full_duplex_mask, full_duplex_val =0 ; +u32 inband_en_mask, inband_val =0 ; + + gig_en_mask = (slice ==ICSS_MII0 ) ?RGMII_CFG_GIG_EN_MII0 : +RGMII_CFG_GIG_EN_MII1 ; +if (speed ==SPEED_1000 ) + gig_val = gig_en_mask; +regmap_update_bits (miig_rt,RGMII_CFG_OFFSET , gig_en_mask, gig_val); + + inband_en_mask = (slice ==ICSS_MII0 ) ?RGMII_CFG_INBAND_EN_MII0 : +RGMII_CFG_INBAND_EN_MII1 ; +if (speed ==SPEED_10 &&phy_interface_is_rgmii (priv->phydev)) + inband_val = inband_en_mask; +regmap_update_bits (miig_rt,RGMII_CFG_OFFSET , inband_en_mask, inband_val); + + full_duplex_mask = (slice ==ICSS_MII0 ) ?RGMII_CFG_FULL_DUPLEX_MII0 : +RGMII_CFG_FULL_DUPLEX_MII1 ; +if (full_duplex) + full_duplex_val = full_duplex_mask; +regmap_update_bits (miig_rt,RGMII_CFG_OFFSET , full_duplex_mask, + full_duplex_val); +} + +static inline void icssg_miig_set_interface_mode (struct regmap *miig_rt,int mii,int phy_if) +{ +u32 val, mask, shift; + + mask = mii ==ICSS_MII0 ?ICSSG_CFG_MII0_MODE :ICSSG_CFG_MII1_MODE ; + shift = mii ==ICSS_MII0 ?ICSSG_CFG_MII0_MODE_SHIFT :ICSSG_CFG_MII1_MODE_SHIFT ; + + val =MII_MODE_RGMII ; +if (phy_if ==PHY_INTERFACE_MODE_MII ) + val =MII_MODE_MII ; + + val <<= shift; +regmap_update_bits (miig_rt,ICSSG_CFG_OFFSET , mask, val); +regmap_read (miig_rt,ICSSG_CFG_OFFSET , &val); +} + +#endif /* __NET_PRUSS_MII_RT_H__ */
drivers/net/ti/icssg_classifier.c new file +376 -0
376 lines not on this page · raw message
drivers/net/ti/icssg_config.c new file +397 -0
397 lines not on this page · raw message
drivers/net/ti/icssg_config.h new file +177 -0
177 lines not on this page · raw message
drivers/net/ti/icssg_prueth.h new file +78 -0
78 lines not on this page · raw message
Signature · 1 line
2.34.1
RFC PATCH v3 6/15 net: ti: icssg: Add icssg queues APIs and macros
In reply to MD Danish AnwarAdd icssg_queue.c file. This file introduces macros and APIs related to ICSSG queues. These will be used by ICSSG Ethernet driver.
--- drivers/net/ti/icssg_prueth.h | 5 ++++ drivers/net/ti/icssg_queues.c | 51 +++++++++++++++++++++++++++++++++++ 2 files changed, 56 insertions(+) create mode 100644 drivers/net/ti/icssg_queues.c
drivers/net/ti/icssg_prueth.h +5 -0
@@ -75,4 +75,9 @@ void icssg_config_ipg(struct prueth *prueth, int speed, int mii);int icssg_config (struct prueth *prueth);int emac_set_port_state (struct prueth *prueth,enum icssg_port_state_cmd cmd); +/* Buffer queue helpers */ +int icssg_queue_pop (struct prueth *prueth,u8 queue); +void icssg_queue_push (struct prueth *prueth,int queue,u16 addr); +u32 icssg_queue_level (struct prueth *prueth,int queue); +#endif /* __NET_TI_ICSSG_PRUETH_H */
drivers/net/ti/icssg_queues.c new file +51 -0
51 lines not on this page · raw message
Signature · 1 line
2.34.1
RFC PATCH v3 7/15 net: ti: icssg: Add ICSSG ethernet driver
In reply to MD Danish AnwarThis is the PURSS Ethernet driver for TI AM654 Sr2.0 and laterSoCs with the ICSSG PRU Sub-system running EMAC firmware. This driver caters to either of the slices of the icssg subsystem.
One and exactly one of the slices is supported as the u-boot ethernet supports probing one interface at a time.
--- drivers/net/ti/Kconfig | 8 + drivers/net/ti/Makefile | 1 + drivers/net/ti/icssg_prueth.c | 697 ++++++++++++++++++++++++++++++++++ drivers/net/ti/icssg_prueth.h | 3 + 4 files changed, 709 insertions(+) create mode 100644 drivers/net/ti/icssg_prueth.c
drivers/net/ti/Kconfig +8 -0
@@ -49,3 +49,11 @@ config TI_AM65_CPSW_NUSS help This driver supports TI K3 MCU CPSW Nuss Ethernet controller in Texas Instruments K3 AM65x SoCs. + +config TI_ICSSG_PRUETH + bool "TI Gigabit PRU Ethernet driver" + depends on ARCH_K3 + select PHYLIB + help + Support Gigabit Ethernet ports over the ICSSG PRU Subsystem + This subsystem is available starting with the AM65 platform.
drivers/net/ti/Makefile +1 -0
@@ -6,3 +6,4 @@ obj-$(CONFIG_DRIVER_TI_CPSW) += cpsw.o cpsw-common.o cpsw_mdio.o obj-$(CONFIG_DRIVER_TI_EMAC) += davinci_emac.o obj-$(CONFIG_DRIVER_TI_KEYSTONE_NET) += keystone_net.o cpsw_mdio.o obj-$(CONFIG_TI_AM65_CPSW_NUSS) += am65-cpsw-nuss.o cpsw_mdio.o +obj-$(CONFIG_TI_ICSSG_PRUETH) += icssg_prueth.o cpsw_mdio.o icssg_classifier.o icssg_config.o icssg_queues.o
drivers/net/ti/icssg_prueth.c new file +697 -0
697 lines not on this page · raw message
drivers/net/ti/icssg_prueth.h +3 -0
@@ -68,6 +68,9 @@ struct prueth {bool mdio_manual_mode;int speed;int duplex; +u8 pru_core_id; +u8 rtu_core_id; +u8 txpru_core_id; };/* config helpers */
Signature · 1 line
2.34.1
RFC PATCH v3 8/15 net: ti: icssg: Add support sending FDB command to update rx_flow_id
In reply to MD Danish AnwarICSSG firmware supports FDB commands. Add support to send FDB commands from driver. Once rx_flow_id is obtained from dma, let firmware know that we are using this rx_flow_id by sending a FDB command.
--- drivers/net/ti/icssg_config.c | 66 +++++++++++++++++++++++++++++++++++ drivers/net/ti/icssg_config.h | 18 ++++++++++ drivers/net/ti/icssg_prueth.c | 6 ++++ drivers/net/ti/icssg_prueth.h | 6 ++++ 4 files changed, 96 insertions(+)
drivers/net/ti/icssg_config.c +66 -0
@@ -9,6 +9,7 @@#include "icssg_switch_map.h" #include "icss_mii_rt.h" #include <dm/device_compat.h> +#include <linux/iopoll.h> /* TX IPG Values to be set for 100M and 1G link speeds. These values are * in ocp_clk cycles. So need change if ocp_clk is changed for a specific
@@ -395,3 +396,68 @@ int emac_set_port_state(struct prueth *prueth,return ret; } + +int icssg_send_fdb_msg (struct prueth *prueth,struct mgmt_cmd *cmd, +struct mgmt_cmd_rsp *rsp) +{ +int slice = prueth->slice; +int ret, addr; + + addr =icssg_queue_pop (prueth, slice ==0 ? +ICSSG_CMD_POP_SLICE0 :ICSSG_CMD_POP_SLICE1 ); +if (addr <0 ) +return addr; + +/* First 4 bytes have FW owned buffer linking info which should +* not be touched +*/ +memcpy_toio ((void __iomem *)prueth->shram.pa + addr +4 , cmd,sizeof (*cmd)); +icssg_queue_push (prueth, slice ==0 ? +ICSSG_CMD_PUSH_SLICE0 :ICSSG_CMD_PUSH_SLICE1 , addr); + ret =read_poll_timeout (icssg_queue_pop, addr, addr >=0 , +2000 ,20000000 , prueth, slice ==0 ? +ICSSG_RSP_POP_SLICE0 :ICSSG_RSP_POP_SLICE1 ); + +if (ret) { +dev_err (prueth->dev,"Timedout sending HWQ message\n" ); +return ret; + } + +memcpy_fromio (rsp, (void __iomem *)prueth->shram.pa + addr,sizeof (*rsp)); +/* Return buffer back for to pool */ +icssg_queue_push (prueth, slice ==0 ? +ICSSG_RSP_PUSH_SLICE0 :ICSSG_RSP_PUSH_SLICE1 , addr); + +return 0 ; +} + +int emac_fdb_flow_id_updated (struct prueth *prueth) +{ +struct mgmt_cmd_rsp fdb_cmd_rsp = {0 }; +int slice = prueth->slice; +struct mgmt_cmd fdb_cmd = {0 }; +int ret =0 ; + + fdb_cmd.header =ICSSG_FW_MGMT_CMD_HEADER ; + fdb_cmd.type =ICSSG_FW_MGMT_FDB_CMD_TYPE_RX_FLOW ; + fdb_cmd.seqnum = ++(prueth->icssg_hwcmdseq); + fdb_cmd.param =0 ; + + fdb_cmd.param |= (slice <<4 ); + fdb_cmd.cmd_args[0 ] =0 ; + + ret =icssg_send_fdb_msg (prueth, &fdb_cmd, &fdb_cmd_rsp); +if (ret) +return ret; + +if (fdb_cmd.seqnum != fdb_cmd_rsp.seqnum) { +dev_err (prueth->dev,"seqnum doesn't match, cmd.seqnum %d != rsp.seqnum %d\n" , + fdb_cmd.seqnum, fdb_cmd_rsp.seqnum); +return -EINVAL ; + } + +if (fdb_cmd_rsp.status ==1 ) +return 0 ; + +return -EINVAL ; +}
drivers/net/ti/icssg_config.h +18 -0
@@ -80,6 +80,7 @@ struct icssg_rxq_ctx {#define ICSSG_FW_MGMT_FDB_CMD_TYPE 0x03#define ICSSG_FW_MGMT_CMD_TYPE 0x04#define ICSSG_FW_MGMT_PKT 0x80000000 +#define ICSSG_FW_MGMT_FDB_CMD_TYPE_RX_FLOW 0x05struct icssg_r30_cmd {u32 cmd[4 ];
@@ -156,6 +157,23 @@ struct icssg_setclock_desc {u32 CMP0_new; } __packed; +struct mgmt_cmd { +u8 param; +u8 seqnum; +u8 type; +u8 header; +u32 cmd_args[3 ]; +} __packed; + +struct mgmt_cmd_rsp { +u32 reserved; +u8 status; +u8 seqnum; +u8 type; +u8 header; +u32 cmd_args[3 ]; +} __packed; +#define ICSSG_CMD_POP_SLICE0 56#define ICSSG_CMD_POP_SLICE1 60
drivers/net/ti/icssg_prueth.c +6 -0
@@ -351,6 +351,12 @@ static int prueth_start(struct udevice *dev)dev_info (dev,"K3 ICSSG: rflow_id_base: %u, chn_name = %s\n" , dma_rx_cfg_data->flow_id_base, chn_name); + ret =emac_fdb_flow_id_updated (priv); +if (ret) { +dev_err (dev,"Failed to update Rx Flow ID %d" , ret); + goto phy_fail; + } + ret =phy_startup (priv->phydev);if (ret) {dev_err (dev,"phy_startup failed\n" );
drivers/net/ti/icssg_prueth.h +6 -0
@@ -71,6 +71,7 @@ struct prueth {u8 pru_core_id;u8 rtu_core_id;u8 txpru_core_id; +u8 icssg_hwcmdseq; };/* config helpers */
@@ -83,4 +84,9 @@ int icssg_queue_pop(struct prueth *prueth, u8 queue);void icssg_queue_push (struct prueth *prueth,int queue,u16 addr);u32 icssg_queue_level (struct prueth *prueth,int queue); +/* FDB helpers */ +int icssg_send_fdb_msg (struct prueth *prueth,struct mgmt_cmd *cmd, +struct mgmt_cmd_rsp *rsp); +int emac_fdb_flow_id_updated (struct prueth *prueth); +#endif /* __NET_TI_ICSSG_PRUETH_H */
Signature · 1 line
2.34.1
RFC PATCH v3 9/15 net: ti: icssg: Enforce pinctrl state on the MDIO child node
In reply to MD Danish AnwarThe binding represents the MDIO controller as a child device tree node of the MAC device tree node.
The U-Boot driver mostly ignores that child device tree node and just hardcodes the resources it uses to support both the MAC and MDIO in a single driver.
However, some resources like pinctrl muxing states are thus ignored. This has been a problem with some device trees that will put some pinctrl states on the MDIO device tree node.
Let's rework the driver a bit to create a dummy MDIO driver that we will then get during our initialization to force the core to select the right muxing.
--- drivers/net/ti/Kconfig | 1 + drivers/net/ti/icssg_prueth.c | 59 +++++++++++++++++++++++++++++++++++ 2 files changed, 60 insertions(+)
drivers/net/ti/Kconfig +1 -0
@@ -53,6 +53,7 @@ config TI_AM65_CPSW_NUSS config TI_ICSSG_PRUETH bool "TI Gigabit PRU Ethernet driver" depends on ARCH_K3 + imply DM_MDIO select PHYLIB help Support Gigabit Ethernet ports over the ICSSG PRU Subsystem
drivers/net/ti/icssg_prueth.c +59 -0
77 lines not on this page · raw message
Signature · 1 line
2.34.1
RFC PATCH v3 10/15 arm: dts: k3-am654-base-board: Add ICSSG2 Ethernet support
In reply to MD Danish AnwarICSSG2 provides dual Gigabit Ethernet support.
Add ICSSG2 ethernet node to an overlay k3-am654-icssg2.dtso
--- arch/arm/dts/Makefile | 3 +- arch/arm/dts/k3-am654-icssg2.dtso | 145 ++++++++++++++++++++++++++++++ 2 files changed, 147 insertions(+), 1 deletion(-) create mode 100644 arch/arm/dts/k3-am654-icssg2.dtso
arch/arm/dts/Makefile +2 -1
@@ -1396,7 +1396,8 @@ dtb-$(CONFIG_SOC_K3_AM654) += \ k3-am6548-iot2050-advanced-pg2.dtb \ k3-am6548-iot2050-advanced-m2.dtb \ k3-am6548-iot2050-advanced-m2-bkey-usb3-overlay.dtbo \ - k3-am6548-iot2050-advanced-m2-bkey-ekey-pcie-overlay.dtbo + k3-am6548-iot2050-advanced-m2-bkey-ekey-pcie-overlay.dtbo \ + k3-am654-icssg2.dtbo dtb-$(CONFIG_SOC_K3_J721E) += k3-j721e-common-proc-board.dtb \ k3-j721e-r5-common-proc-board.dtb \ k3-j7200-common-proc-board.dtb \
arch/arm/dts/k3-am654-icssg2.dtso new file +145 -0
145 lines not on this page · raw message
Signature · 1 line
2.34.1
RFC PATCH v3 11/15 arm: dts: k3-am65x-binman: Add ICSSG2 overlay and configuration
In reply to MD Danish AnwarAdd ICSSG2 overlay and configuration to tispl and u-boot images.
--- arch/arm/dts/k3-am65x-binman.dtsi | 65 +++++++++++++++++++++++++++++-- 1 file changed, 61 insertions(+), 4 deletions(-)
arch/arm/dts/k3-am65x-binman.dtsi +61 -4
@@ -98,6 +98,8 @@ #define SPL_AM654_EVM_DTB "spl/dts/k3-am654-base-board.dtb" #define AM654_EVM_DTB "u-boot.dtb" +#define AM654_EVM_ICSSG2_DTBO "arch/arm/dts/k3-am654-icssg2.dtbo" + &binman { ti-spl { insert-template = <&ti_spl_template>;
@@ -124,6 +126,20 @@ filename = SPL_AM654_EVM_DTB; }; }; + + fdt-1 { + description = "k3-am654-icssg2 overlay"; + type = "flat_dt"; + arch = "arm"; + compression = "none"; + ti-secure { + content = <&spl_am65x_evm_icssg2_dtb>; + keyfile = "custMpk.pem"; + }; + spl_am65x_evm_icssg2_dtb: blob-ext { + filename = AM654_EVM_ICSSG2_DTBO; + }; + }; }; configurations {
@@ -133,7 +149,7 @@ description = "k3-am654-base-board"; firmware = "atf"; loadables = "tee", "dm", "spl"; - fdt = "fdt-0"; + fdt = "fdt-0", "fdt-1"; }; }; };
@@ -168,6 +184,24 @@ }; }; + fdt-1 { + description = "k3-am654-icssg2 overlay"; + type = "flat_dt"; + arch = "arm"; + compression = "none"; + ti-secure { + content = <&am65x_evm_icssg2_dtb>; + keyfile = "custMpk.pem"; + + }; + am65x_evm_icssg2_dtb: blob-ext { + filename = AM654_EVM_ICSSG2_DTBO; + }; + hash { + algo = "crc32"; + }; + }; + }; configurations {
@@ -177,7 +211,7 @@ description = "k3-am654-base-board"; firmware = "uboot"; loadables = "uboot"; - fdt = "fdt-0"; + fdt = "fdt-0", "fdt-1"; }; }; };
@@ -205,6 +239,16 @@ filename = SPL_AM654_EVM_DTB; }; }; + + fdt-1 { + description = "k3-am654-icssg2 overlay"; + type = "flat_dt"; + arch = "arm"; + compression = "none"; + blob { + filename = AM654_EVM_ICSSG2_DTBO; + }; + }; }; configurations {
@@ -214,7 +258,7 @@ description = "k3-am654-base-board"; firmware = "atf"; loadables = "tee", "dm", "spl"; - fdt = "fdt-0"; + fdt = "fdt-0", "fdt-1"; }; }; };
@@ -243,6 +287,19 @@ algo = "crc32"; }; }; + + fdt-1 { + description = "k3-am654-icssg2"; + type = "flat_dt"; + arch = "arm"; + compression = "none"; + blob { + filename = AM654_EVM_ICSSG2_DTBO; + }; + hash { + algo = "crc32"; + }; + }; }; configurations {
@@ -252,7 +309,7 @@ description = "k3-am654-base-board"; firmware = "uboot"; loadables = "uboot"; - fdt = "fdt-0"; + fdt = "fdt-0", "fdt-1"; }; }; };
Signature · 1 line
2.34.1
RFC PATCH v3 12/15 configs: am65x_evm_a53: Enable ICSSG Driver
In reply to MD Danish AnwarEnable ICSSG driver in am65x_evm_a53_defconfig
--- configs/am65x_evm_a53_defconfig | 1 + 1 file changed, 1 insertion(+)
configs/am65x_evm_a53_defconfig +1 -0
@@ -129,6 +129,7 @@ CONFIG_PHY_FIXED=y CONFIG_E1000=y CONFIG_CMD_E1000=y CONFIG_TI_AM65_CPSW_NUSS=y +CONFIG_TI_ICSSG_PRUETH=y CONFIG_PCI_KEYSTONE=y CONFIG_PHY=y CONFIG_SPL_PHY=y
Signature · 1 line
2.34.1
RFC PATCH v3 13/15 configs: am65x_evm_a53: add SPL_LOAD_FIT_APPLY_OVERLAY
In reply to MD Danish AnwarWe want SPL to apply DTB overlays (e.g. ICSSG2 overlay) so enable SPL_LOAD_FIT_APPLY_OVERLAY.
--- configs/am65x_evm_a53_defconfig | 1 + 1 file changed, 1 insertion(+)
configs/am65x_evm_a53_defconfig +1 -0
@@ -69,6 +69,7 @@ CONFIG_CMD_I2C=y CONFIG_CMD_MMC=y CONFIG_CMD_PCI=y CONFIG_CMD_REMOTEPROC=y +CONFIG_SPL_LOAD_FIT_APPLY_OVERLAY=y CONFIG_CMD_USB=y CONFIG_CMD_TIME=y CONFIG_MTDIDS_DEFAULT="nor0=47040000.spi.0"
Signature · 1 line
2.34.1
RFC PATCH v3 14/15 board: ti: am65x: Add check for k3-am654-icssg2 in board_fit_config_match()
In reply to MD Danish AnwarWhen CONFIG_TI_ICSSG_PRUETH is enabled, add config name check for the icssg2 overlay in board_fit_config_match() API.
--- board/ti/am65x/evm.c | 11 +++++++---- 1 file changed, 7 insertions(+), 4 deletions(-)
board/ti/am65x/evm.c +7 -4
@@ -90,10 +90,13 @@ int dram_init_banksize(void)#ifdef CONFIG_SPL_LOAD_FIT int board_fit_config_name_match (const char *name) { -#ifdef CONFIG_TARGET_AM654_A53_EVM -if (!strcmp (name,"k3-am654-base-board" )) -return 0 ; -#endif +if (IS_ENABLED (CONFIG_TI_ICSSG_PRUETH )) { +if (!strcmp (name,"k3-am654-icssg2" )) +return 0 ; + }else { +if (!strcmp (name,"k3-am654-base-board" )) +return 0 ; + }return -1 ; }
Signature · 1 line
2.34.1
Re: [RFC PATCH v3 14/15] board: ti: am65x: Add check for k3-am654-icssg2 in board_fit_config_match()
Quoted 20 lines · MD Danish Anwar
When
CONFIG_TI_ICSSG_PRUETHis enabled, add config name check for the icssg2 overlay inboard_fit_config_match()API.Signed-off-by MD Danish Anwar <[email protected]>--- board/ti/am65x/evm.c | 11 +++++++---- 1 file changed, 7 insertions(+), 4 deletions(-)board/ti/am65x/evm.c +0
-4@@ -90,10 +90,13 @@ int dram_init_banksize(void)#ifdef CONFIG_SPL_LOAD_FIT int board_fit_config_name_match (const char *name) { -#ifdef CONFIG_TARGET_AM654_A53_EVM -if (!strcmp (name,"k3-am654-base-board" )) -return 0 ; -#endif
board/ti/am65x/evm.c int dram_init_banksize(void) · line 102
Quoted 10 lines
board/ti/am65x/evm.c +7
-0+if (IS_ENABLED (CONFIG_TI_ICSSG_PRUETH )) { +if (!strcmp (name,"k3-am654-icssg2" )) +return 0 ; + }else { +if (!strcmp (name,"k3-am654-base-board" )) +return 0 ; + }return -1 ; }
It probably should support both configs being enabled.
if (IS_ENABLED(CONFIG_TI_ICSSG_PRUETH) && strcmp(name, "k3-am654-icssg2") == 0) return 0; if (IS_ENABLED(TARGET_AM654_A53_EVM) && strcmp(name, "k3-am654-base-board")) return 0; return -1;
regards,
dan carpenter
Re: [RFC PATCH v3 14/15] board: ti: am65x: Add check for k3-am654-icssg2 in board_fit_config_match()
Quoted 34 lines · Dan Carpenter
Quoted 20 lines · MD Danish Anwar
When
CONFIG_TI_ICSSG_PRUETHis enabled, add config name check for the icssg2 overlay inboard_fit_config_match()API.Signed-off-by MD Danish Anwar <[email protected]>--- board/ti/am65x/evm.c | 11 +++++++---- 1 file changed, 7 insertions(+), 4 deletions(-)board/ti/am65x/evm.c +0
-4@@ -90,10 +90,13 @@ int dram_init_banksize(void)#ifdef CONFIG_SPL_LOAD_FIT int board_fit_config_name_match (const char *name) { -#ifdef CONFIG_TARGET_AM654_A53_EVM -if (!strcmp (name,"k3-am654-base-board" )) -return 0 ; -#endif board/ti/am65x/evm.c int dram_init_banksize(void) · line 102
Quoted 10 lines
board/ti/am65x/evm.c +7
-0+if (IS_ENABLED (CONFIG_TI_ICSSG_PRUETH )) { +if (!strcmp (name,"k3-am654-icssg2" )) +return 0 ; + }else { +if (!strcmp (name,"k3-am654-base-board" )) +return 0 ; + }return -1 ; }It probably should support both configs being enabled.
Quoted 10 lines
if (IS_ENABLED(CONFIG_TI_ICSSG_PRUETH) && strcmp(name, "k3-am654-icssg2") == 0) return 0; if (IS_ENABLED(TARGET_AM654_A53_EVM) && strcmp(name, "k3-am654-base-board")) return 0; return -1;
Sure Dan. This seems reasonable. I will add check for both configs in next revision. Thanks for the review.
Quoted 2 lines
regards,
dan carpenter
Signature · 2 lines
Thanks and Regards, Danish
Re: [RFC PATCH v3 14/15] board: ti: am65x: Add check for k3-am654-icssg2 in board_fit_config_match()
In reply to Dan CarpenterQuoted 34 lines · Dan Carpenter
Quoted 20 lines · MD Danish Anwar
When
CONFIG_TI_ICSSG_PRUETHis enabled, add config name check for the icssg2 overlay inboard_fit_config_match()API.Signed-off-by MD Danish Anwar <[email protected]>--- board/ti/am65x/evm.c | 11 +++++++---- 1 file changed, 7 insertions(+), 4 deletions(-)board/ti/am65x/evm.c +0
-4@@ -90,10 +90,13 @@ int dram_init_banksize(void)#ifdef CONFIG_SPL_LOAD_FIT int board_fit_config_name_match (const char *name) { -#ifdef CONFIG_TARGET_AM654_A53_EVM -if (!strcmp (name,"k3-am654-base-board" )) -return 0 ; -#endif board/ti/am65x/evm.c int dram_init_banksize(void) · line 102
Quoted 10 lines
board/ti/am65x/evm.c +7
-0+if (IS_ENABLED (CONFIG_TI_ICSSG_PRUETH )) { +if (!strcmp (name,"k3-am654-icssg2" )) +return 0 ; + }else { +if (!strcmp (name,"k3-am654-base-board" )) +return 0 ; + }return -1 ; }It probably should support both configs being enabled.
Quoted 6 lines
if (IS_ENABLED(CONFIG_TI_ICSSG_PRUETH) && strcmp(name, "k3-am654-icssg2") == 0) return 0; if (IS_ENABLED(TARGET_AM654_A53_EVM) && strcmp(name, "k3-am654-base-board"))
I reversed this strcmp()...
strcmp(name, "k3-am654-base-board") == 0)
regards,
dan carpenter
RFC PATCH v3 15/15 board: ti: am65x: Set fw_storage_interface and fw_dev_part ENVs
In reply to MD Danish AnwarWhen ICSSG driver is enabled (CONFIG_TI_ICSSG_PRUETH=y) set fw_storage_interface and fw_dev_part env variables.
These variables need be set appropriately in order to load differnet ICSSG firmwares needed for ICSSG driver. By default the storage interface is mmc and the partition is 1:2. User can modify this based on their needs.
--- board/ti/am65x/am65x.env | 4 ++++ 1 file changed, 4 insertions(+)
board/ti/am65x/am65x.env +4 -0
@@ -30,3 +30,7 @@ get_fdt_ubi=ubifsload ${fdtaddr} ${bootdir}/${name_fdt} args_ubi=setenv bootargs console=${console} ${optargs} rootfstype=ubifs root=ubi0:rootfs rw ubi.mtd=ospi.rootfs +#if CONFIG_TI_ICSSG_PRUETH +fw_storage_interface=mmc +fw_dev_part=1:2 +#endif
Signature · 1 line
2.34.1