nxp: imx: Add support for Apalis Evaluation Board v1.2
Subsystems (2)
v2 cover nxp: imx: Add support for Apalis Evaluation Board v1.2
From: Hiago De Franco <[email protected]>
This patch series introduces support for the new Apalis Evaluation Board v1.2. With the introduction of v1.2, a common dtsi file, containing shared configurations for both apalis-eval.dts and apalis-eval-v1.2.dts, has been created. The eval and eval-v1.2 dts files will now capture the differences between these two boards. Additionally, updates have been made to nxp/imx/Makefile and arm/fsl.yaml to accommodate these changes.
v1:
- https://lore.kernel.org/all/[email protected]/
v2:
- Add missing off-on-delay-us property with 100ms to reg_3v3_mmc and reg_3v3_sd.
- Fix startup-delay-us property from 100us (reg_3v3_mmc and reg_3v3_sd) and 1ms (reg_can1 and reg_can2) to 10ms.
- Fix pinctrl mux from 0xb000 to 0x1b0b0.
- Add Acked-by: Conor Dooley.
- Add Reviewed-by: Francesco Dolcini.
Hiago De Franco (2):
dt-bindings: arm: fsl: Add toradex,apalis_imx6q-eval-v1.2 board
arm: dts: nxp: imx: Add support for Apalis Evaluation Board v1.2
.../devicetree/bindings/arm/fsl.yaml | 3 +- arch/arm/boot/dts/nxp/imx/Makefile | 1 + .../dts/nxp/imx/imx6q-apalis-eval-v1.2.dts | 200 ++++++++++++++++++ .../boot/dts/nxp/imx/imx6q-apalis-eval.dts | 108 +--------- .../boot/dts/nxp/imx/imx6q-apalis-eval.dtsi | 120 +++++++++++ 5 files changed, 325 insertions(+), 107 deletions(-) create mode 100644 arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval-v1.2.dts create mode 100644 arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval.dtsi
Signature · 1 line
2.43.0
PATCH v2 1/2 dt-bindings: arm: fsl: Add toradex,apalis_imx6q-eval-v1.2 board
From: Hiago De Franco <[email protected]>
Add the toradex,apalis_imx6q-eval-v1.2 compatible string for version 1.2 of the Apalis Evaluation Board.
Version v1.2 includes the following changes compared to v1.1:
- 8-bit MMC connector replaced with a 4-bit uSD connector.
- Audio codec NAU88C22 added.
- M24C02 EEPROM i2c added.
- MIPI-CSI-2 connector directly to the board added.
- PCIe switch PEX8605 removed and PCIe now is routed directly to Mini PCIe connector.
- Power measurement IC INA219 added.
- Replaced DVI with HDMI connector.
- Single-channel USB to UART converter replaced with four-channel USB to UART/JTAG.
- Temperature sensor TMP75 added.
Please note that version v1.0 (which reached EOL) is compatible with v1.1, therefore toradex,apalis_imx6q-eval compatible string should be used for both v1.0 and v1.1.
---
v2:
- Add Acked-by: Conor Dooley.
--- Documentation/devicetree/bindings/arm/fsl.yaml | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
Documentation/devicetree/bindings/arm/fsl.yaml +2 -1
@@ -384,7 +384,8 @@ properties: - toradex,apalis_imx6q-ixora # Apalis iMX6Q/D Module on Ixora Carrier Board - toradex,apalis_imx6q-ixora-v1.1 # Apalis iMX6Q/D Module on Ixora V1.1 Carrier Board - toradex,apalis_imx6q-ixora-v1.2 # Apalis iMX6Q/D Module on Ixora V1.2 Carrier Board - - toradex,apalis_imx6q-eval # Apalis iMX6Q/D Module on Apalis Evaluation Board + - toradex,apalis_imx6q-eval # Apalis iMX6Q/D Module on Apalis Evaluation Board v1.0/v1.1 + - toradex,apalis_imx6q-eval-v1.2 # Apalis iMX6Q/D Module on Apalis Evaluation Board v1.2 - const: toradex,apalis_imx6q - const: fsl,imx6q
Signature · 1 line
2.43.0
PATCH v2 2/2 arm: dts: nxp: imx: Add support for Apalis Evaluation Board v1.2
In reply to Hiago De FrancoFrom: Hiago De Franco <[email protected]>
Add support for the new Apalis Evaluation Board v1.2. Because only the imx6q-apalis-eval.dts was available, the imx6q-apalis-eval.dtsi has been created which has common hardware configurations for v1.0, v1.1 and v1.2. Both imx6q-apalis-eval.dts and imx6q-apalis-eval-v1.2.dts files include imx6q-apalis-eval.dtsi.
Versions 1.0 and 1.1 are compatible with each other and should use imx6q-apalis-eval.dts file. Now for v1.2, the new device-tree file should be used.
---
v2:
- Add missing off-on-delay-us property with 100ms to reg_3v3_mmc and reg_3v3_sd.
- Fix startup-delay-us property from 100us (reg_3v3_mmc and reg_3v3_sd) and 1ms (reg_can1 and reg_can2) to 10ms.
- Fix pinctrl mux from 0xb000 to 0x1b0b0.
- Add Reviewed-by: Francesco Dolcini.
--- arch/arm/boot/dts/nxp/imx/Makefile | 1 + .../dts/nxp/imx/imx6q-apalis-eval-v1.2.dts | 200 ++++++++++++++++++ .../boot/dts/nxp/imx/imx6q-apalis-eval.dts | 108 +--------- .../boot/dts/nxp/imx/imx6q-apalis-eval.dtsi | 120 +++++++++++ 4 files changed, 323 insertions(+), 106 deletions(-) create mode 100644 arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval-v1.2.dts create mode 100644 arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval.dtsi
arch/arm/boot/dts/nxp/imx/Makefile +1 -0
@@ -147,6 +147,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6dl-yapp4-phoenix.dtb \ imx6dl-yapp4-ursa.dtb \ imx6q-apalis-eval.dtb \ + imx6q-apalis-eval-v1.2.dtb \ imx6q-apalis-ixora.dtb \ imx6q-apalis-ixora-v1.1.dtb \ imx6q-apalis-ixora-v1.2.dtb \
arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval-v1.2.dts new file +200 -0
200 lines not on this page · raw message
arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval.dts +2 -106
147 lines not on this page · raw message
arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval.dtsi new file +120 -0
120 lines not on this page · raw message
Signature · 1 line
2.43.0
Shawn Guo
AppliedQuoted 3 lines · Hiago De Franco
Hiago De Franco (2):
dt-bindings: arm: fsl: Add toradex,apalis_imx6q-eval-v1.2 board
arm: dts: nxp: imx: Add support for Apalis Evaluation Board v1.2
Changed the subject prefix of the second one to 'ARM: dts: imx: ...'
Applied both, thanks!
Shawn