Skip to contentSkip to conversation

hwmon: Add driver for NZXT Kraken X and Z series AIO CPU coolers

PATCH Applied Aleksa Savic 2 participants 2 messages Jan 29, 2024 – Feb 2, 2024

Subsystems (3)
lore
Share & tools
lore

Aleksa Savic

author maintainer
#0 lore raw

PATCH 1/1 hwmon: Add driver for NZXT Kraken X and Z series AIO CPU coolers

This driver enables hardware monitoring support for NZXT Kraken X53/X63/X73 and Z53/Z63/Z73 all-in-one CPU liquid coolers.

All models expose liquid temperature and pump speed (in RPM), as well as PWM control (natively only through a temp-PWM curve, but the driver also emulates fixed PWM control on top of that). The Z-series models additionally expose the speed and duty of an optionally connected fan, with the same PWM control capabilities.

Pump and fan duty control mode can be set through pwm[1-2]_enable, where 1 is for the manual control mode and 2 is for the liquid temp to PWM curve mode. Writing a 0 disables control of the channel through the driver after setting its duty to 100%. As it is not possible to query the device for the active mode, the driver keeps track of it.

The temperature of the curves relates to the fixed [20-59] C range, per device limitations, and correlating to the detected liquid temperature. Only PWM values (ranging from 0-255) can be set.

The addressable RGB LEDs and LCD screen, included only on Z-series models, are not supported in this driver.

---
 Documentation/hwmon/index.rst        |    1 +
 Documentation/hwmon/nzxt-kraken3.rst |   74 ++
 MAINTAINERS                          |    8 +
 drivers/hwmon/Kconfig                |   10 +
 drivers/hwmon/Makefile               |    1 +
 drivers/hwmon/nzxt-kraken3.c         | 1008 ++++++++++++++++++++++++++
 6 files changed, 1102 insertions(+)
 create mode 100644 Documentation/hwmon/nzxt-kraken3.rst
 create mode 100644 drivers/hwmon/nzxt-kraken3.c
Documentation/hwmon/index.rst +1 -0
index c7ed1f73ac06..7b3bc243b115 100644
@@ -171,6 +171,7 @@ Hardware Monitoring Kernel Drivers
    nsa320
    ntc_thermistor
    nzxt-kraken2
+   nzxt-kraken3
    nzxt-smart2
    occ
    oxp-sensors
Documentation/hwmon/nzxt-kraken3.rst new file +74 -0

74 lines not on this page · raw message

MAINTAINERS +8 -0
index 5e7239cb40ea..f5e66daebf1e 100644
@@ -15811,6 +15811,14 @@ S:	Maintained
 F:	Documentation/hwmon/nzxt-kraken2.rst
 F:	drivers/hwmon/nzxt-kraken2.c
 
+NZXT-KRAKEN3 HARDWARE MONITORING DRIVER
+M:	Jonas Malaco <[email protected]>
+M:	Aleksa Savic <[email protected]>
+L:	[email protected]
+S:	Maintained
+F:	Documentation/hwmon/nzxt-kraken3.rst
+F:	drivers/hwmon/nzxt-kraken3.c
+
 NZXT-SMART2 HARDWARE MONITORING DRIVER
 M:	Aleksandr Mezin <[email protected]>
 L:	[email protected]
drivers/hwmon/Kconfig +10 -0
index a608264da87d..10b8f219fac6 100644
@@ -1674,6 +1674,16 @@ config SENSORS_NZXT_KRAKEN2
 	  This driver can also be built as a module. If so, the module
 	  will be called nzxt-kraken2.
 
+config SENSORS_NZXT_KRAKEN3
+	tristate "NZXT Kraken X53/X63/X73, Z53/Z63/Z73 coolers"
+	depends on USB_HID
+	help
+	  If you say yes here you get support for hardware monitoring for the
+	  NZXT Kraken X53/X63/X73, Z53/Z63/Z73 all-in-one CPU liquid coolers.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called nzxt-kraken3.
+
 config SENSORS_NZXT_SMART2
 	tristate "NZXT RGB & Fan Controller/Smart Device v2"
 	depends on USB_HID
drivers/hwmon/Makefile +1 -0
index 47be39af5c03..5ffeb0ad7fbb 100644
@@ -173,6 +173,7 @@ obj-$(CONFIG_SENSORS_NPCM7XX)	+= npcm750-pwm-fan.o
 obj-$(CONFIG_SENSORS_NSA320)	+= nsa320-hwmon.o
 obj-$(CONFIG_SENSORS_NTC_THERMISTOR)	+= ntc_thermistor.o
 obj-$(CONFIG_SENSORS_NZXT_KRAKEN2) += nzxt-kraken2.o
+obj-$(CONFIG_SENSORS_NZXT_KRAKEN3) += nzxt-kraken3.o
 obj-$(CONFIG_SENSORS_NZXT_SMART2) += nzxt-smart2.o
 obj-$(CONFIG_SENSORS_OXP) += oxp-sensors.o
 obj-$(CONFIG_SENSORS_PC87360)	+= pc87360.o
drivers/hwmon/nzxt-kraken3.c new file +1008 -0

1,008 lines not on this page · raw message

Signature · 1 line
2.43.0
maintainer Applied
#1 lore raw
Quoted 19 lines · Aleksa Savic

This driver enables hardware monitoring support for NZXT Kraken X53/X63/X73 and Z53/Z63/Z73 all-in-one CPU liquid coolers.

All models expose liquid temperature and pump speed (in RPM), as well as PWM control (natively only through a temp-PWM curve, but the driver also emulates fixed PWM control on top of that). The Z-series models additionally expose the speed and duty of an optionally connected fan, with the same PWM control capabilities.

Pump and fan duty control mode can be set through pwm[1-2]_enable, where 1 is for the manual control mode and 2 is for the liquid temp to PWM curve mode. Writing a 0 disables control of the channel through the driver after setting its duty to 100%. As it is not possible to query the device for the active mode, the driver keeps track of it.

The temperature of the curves relates to the fixed [20-59] C range, per device limitations, and correlating to the detected liquid temperature. Only PWM values (ranging from 0-255) can be set.

Quoted 8 lines

The addressable RGB LEDs and LCD screen, included only on Z-series models, are not supported in this driver.

Applied.

Thanks,
Guenter