Skip to contentSkip to conversation

dt-bindings: i2c: pca954x: Add custom properties for MAX7357

PATCH RESEND Applied Naresh Solanki 2 participants 3 messages Jan 30, 2024

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH RESEND v5 1/2 dt-bindings: i2c: pca954x: Add custom properties for MAX7357

From: Patrick Rudolph <[email protected]>

Maxim Max7357 has a configuration register to enable additional features. These features aren't enabled by default & its up to board designer to enable the same as it may have unexpected side effects.

These should be validated for proper functioning & detection of devices in secondary bus as sometimes it can cause secondary bus being disabled.

Add booleans for:
- maxim,isolate-stuck-channel
- maxim,send-flush-out-sequence
- maxim,preconnection-wiggle-test-enable

---
Changes in V5:
- Append Reviewer-by
Changes in V4:
- Drop max7358.
Changes in V3:
- Update commit message
Changes in V2:
- Update properties.

---
 .../bindings/i2c/i2c-mux-pca954x.yaml         | 30 +++++++++++++++++++
 1 file changed, 30 insertions(+)
Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml +30 -0
index 2d7bb998b0e9..9aa0585200c9 100644
@@ -71,6 +71,23 @@ properties:
     description: A voltage regulator supplying power to the chip. On PCA9846
       the regulator supplies power to VDD2 (core logic) and optionally to VDD1.
 
+  maxim,isolate-stuck-channel:
+    type: boolean
+    description: Allows to use non faulty channels while a stuck channel is
+      isolated from the upstream bus. If not set all channels are isolated from
+      the upstream bus until the fault is cleared.
+
+  maxim,send-flush-out-sequence:
+    type: boolean
+    description: Send a flush-out sequence to stuck auxiliary buses
+      automatically after a stuck channel is being detected.
+
+  maxim,preconnection-wiggle-test-enable:
+    type: boolean
+    description: Send a STOP condition to the auxiliary buses when the switch
+      register activates a channel to detect a stuck high fault. On fault the
+      channel is isolated from the upstream bus.
+
 required:
   - compatible
   - reg
@@ -95,6 +112,19 @@ allOf:
         "#interrupt-cells": false
         interrupt-controller: false
 
+  - if:
+      not:
+        properties:
+          compatible:
+            contains:
+              enum:
+                - maxim,max7357
+    then:
+      properties:
+        maxim,isolate-stuck-channel: false
+        maxim,send-flush-out-sequence: false
+        maxim,preconnection-wiggle-test-enable: false
+
 unevaluatedProperties: false
 
 examples:

base-commit: 41bccc98fb7931d63d03f326a746ac4d429c1dd3

Signature · 1 line
2.42.0
#1 lore raw

PATCH RESEND v5 2/2 i2c: muxes: pca954x: Enable features on MAX7357

From: Patrick Rudolph <[email protected]>

Enable additional features based on DT settings and unconditionally release the shared interrupt pin after 1.6 seconds and allow to use it as reset.

These features aren't enabled by default and it's up to board designer to validate for proper functioning and detection of devices in secondary bus as sometimes it can cause secondary bus being disabled.

---
Changes in V5:
- Fix typos
- Update comment
- Add newline in dev_warn
Changes in V4:
- Drop max7358
- Update #define
- Move conf variable
- Print warning when I2C_FUNC_SMBUS_WRITE_BYTE_DATA isn't supported Changes in V3:
- Delete unused #define
- Update pca954x_init
- Update commit message
Changes in V2:
- Update comments
- Update check for DT properties

---
 drivers/i2c/muxes/i2c-mux-pca954x.c | 43 ++++++++++++++++++++++++++++-
 1 file changed, 42 insertions(+), 1 deletion(-)
drivers/i2c/muxes/i2c-mux-pca954x.c +42 -1
index 2219062104fb..f5dfc33b97c0 100644
@@ -57,6 +57,20 @@
 
 #define PCA954X_IRQ_OFFSET 4
 
+/*
+ * MAX7357's configuration register is writeable after POR, but
+ * can be locked by setting the basic mode bit. MAX7358 configuration
+ * register is locked by default and needs to be unlocked first.
+ * The configuration register holds the following settings:
+ */
+#define MAX7357_CONF_INT_ENABLE			BIT(0)
+#define MAX7357_CONF_FLUSH_OUT			BIT(1)
+#define MAX7357_CONF_RELEASE_INT		BIT(2)
+#define MAX7357_CONF_DISCON_SINGLE_CHAN		BIT(4)
+#define MAX7357_CONF_PRECONNECT_TEST		BIT(7)
+
+#define MAX7357_POR_DEFAULT_CONF		MAX7357_CONF_INT_ENABLE
+
 enum pca_type {
 	max_7356,
 	max_7357,
@@ -470,7 +484,34 @@ static int pca954x_init(struct i2c_client *client, struct pca954x *data)
 	else
 		data->last_chan = 0; /* Disconnect multiplexer */
 
-	ret = i2c_smbus_write_byte(client, data->last_chan);
+	if (device_is_compatible(&client->dev, "maxim,max7357")) {
+		if (i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_WRITE_BYTE_DATA)) {
+			u8 conf = MAX7357_POR_DEFAULT_CONF;
+			/*
+			 * The interrupt signal is shared with the reset pin. Release the
+			 * interrupt after 1.6 seconds to allow using the pin as reset.
+			 */
+			conf |= MAX7357_CONF_RELEASE_INT;
+
+			if (device_property_read_bool(&client->dev, "maxim,isolate-stuck-channel"))
+				conf |= MAX7357_CONF_DISCON_SINGLE_CHAN;
+			if (device_property_read_bool(&client->dev,
+						      "maxim,send-flush-out-sequence"))
+				conf |= MAX7357_CONF_FLUSH_OUT;
+			if (device_property_read_bool(&client->dev,
+						      "maxim,preconnection-wiggle-test-enable"))
+				conf |= MAX7357_CONF_PRECONNECT_TEST;
+
+			ret = i2c_smbus_write_byte_data(client, data->last_chan, conf);
+		} else {
+			dev_warn(&client->dev, "Write byte data not supported."
+				 "Cannot enable enhanced mode features\n");
+			ret = i2c_smbus_write_byte(client, data->last_chan);
+		}
+	} else {
+		ret = i2c_smbus_write_byte(client, data->last_chan);
+	}
+
 	if (ret < 0)
 		data->last_chan = 0;
 
Signature · 1 line
2.42.0
maintainer Applied
#2 lore raw
In reply to Naresh Solanki

Hi Naresh,

Quoted 8 lines · Naresh Solanki

Maxim Max7357 has a configuration register to enable additional features. These features aren't enabled by default & its up to board designer to enable the same as it may have unexpected side effects.

These should be validated for proper functioning & detection of devices in secondary bus as sometimes it can cause secondary bus being disabled.

[...]

Applied to i2c/i2c-host on

git://git.kernel.org/pub/scm/linux/kernel/git/andi.shyti/linux.git

Thank you,
Andi

Patches applied
===============
[1/2] dt-bindings: i2c: pca954x: Add custom properties for MAX7357

      commit: 8e7d967f04df0fa2c2db00f47ac4cd5ea16ade91
[2/2] i2c: muxes: pca954x: Enable features on MAX7357
      commit: 6b572ea231236bb3be4b819d92119470ac121a9e