Add CSI2RX capture support on TI J7 platforms
v3 cover Add CSI2RX capture support on TI J7 platforms
Hi,
This series adds support for CSI2RX capture support on J7 platforms, series was tested for CSI2RX capture on OV5640 sensor and RPI camera v2 IMX219 sensor on J721e Common Processor Board, J721E Starter kit, J721S2 Common Processor Board, AM68 Starter Kit, J784s4 EVM and AM69 Starter kit.
V1: https://lore.kernel.org/all/[email protected]/
V2: https://lore.kernel.org/all/[email protected]/
Changelog:V2->V3:
* Fix order of properties in patch 6/7/8 as per dts coding style.V1->V2:
* Address feedback from Jai and Andrew
* Rename overlays to indicate first platform supported/dual camera.
* Add missed build test.
* Add board schematics for all commit messages.
Test logs:
J721E EVM OV5640 - https://gist.github.com/vaishnavachath/b08521386cfbe1939facf39b8b2d796b
J721S2 EVM OV5640 - https://gist.github.com/vaishnavachath/1b0d60da6b6464cf12334cd5e161a79b
J784s4 EVM OV5640 - https://gist.github.com/vaishnavachath/02b70df94d2d41662eff99f4ce966d67
TDA4VM SK IMX219 - https://gist.github.com/vaishnavachath/64fc6edd6cc060027812bebd6573df07
AM68 SK IMX219 - https://gist.github.com/vaishnavachath/d522254ff5e797bc853e0706fbea932a
AM69 SK IMX219 - https://gist.github.com/vaishnavachath/8dbd960cc89d691886df371c53aac399
Only a single set of overlays for dual RPI IMX219 is included in the series for reference and other overlays to test OV5640 can be found here:
https://gist.github.com/vaishnavachath/d0a052106892fe9f3096733931e9ad5f
Vaishnav Achath (9):
arm64: dts: ti: k3-j721s2-common-proc-board: Enable camera peripherals
arm64: dts: ti: k3-j784s4-evm: Enable camera peripherals
arm64: dts: ti: k3-am68-sk-base-board: Enable camera peripherals
arm64: dts: ti: k3-am69-sk: Enable camera peripherals
arm64: dts: ti: k3-j721e-sk: Model CSI2RX connector mux
arm64: dts: ti: k3-j721e-main: Add CSI2RX capture nodes
arm64: dts: ti: k3-j721s2-main: Add CSI2RX capture nodes
arm64: dts: ti: k3-j784s4-main: Add CSI2RX capture nodes
arm64: dts: ti: k3-j721e-sk: Add overlay for IMX219
arch/arm64/boot/dts/ti/Makefile | 13 ++ .../boot/dts/ti/k3-am68-sk-base-board.dts | 50 +++++ arch/arm64/boot/dts/ti/k3-am69-sk.dts | 51 +++++ arch/arm64/boot/dts/ti/k3-j721e-main.dtsi | 122 ++++++++++++ .../dts/ti/k3-j721e-sk-csi2-dual-imx219.dtso | 125 ++++++++++++ arch/arm64/boot/dts/ti/k3-j721e-sk.dts | 19 +- .../dts/ti/k3-j721s2-common-proc-board.dts | 25 +++ arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi | 123 +++++++++++- arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 25 +++ arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi | 183 +++++++++++++++++- 10 files changed, 732 insertions(+), 4 deletions(-) create mode 100644 arch/arm64/boot/dts/ti/k3-j721e-sk-csi2-dual-imx219.dtso
Signature · 1 line
2.34.1
PATCH v3 1/9 arm64: dts: ti: k3-j721s2-common-proc-board: Enable camera peripherals
CSI cameras are controlled using I2C. On J721S2 Common Processor Board, this is routed to I2C-5, so enable the instance and the TCA6408 GPIO expander on the bus.
Common Processor Board schematics: https://www.ti.com/lit/zip/sprr411
J721S2 SoM schematics: https://www.ti.com/lit/zip/sprr439
---
V1->V2: Update commit message with schematics.
.../dts/ti/k3-j721s2-common-proc-board.dts | 25 +++++++++++++++++++ 1 file changed, 25 insertions(+)
arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts +25 -0
@@ -147,6 +147,13 @@ J721S2_IOPAD(0x060, PIN_INPUT_PULLUP, 13) /* (AC27) MCASP2_AXR1.I2C3_SDA */ >; }; + main_i2c5_pins_default: main-i2c5-default-pins { + pinctrl-single,pins = < + J721S2_IOPAD(0x01c, PIN_INPUT, 8) /* (Y24) MCAN15_TX.I2C5_SCL */ + J721S2_IOPAD(0x018, PIN_INPUT, 8) /* (W23) MCAN14_RX.I2C5_SDA */ + >; + }; + main_mmc1_pins_default: main-mmc1-default-pins { pinctrl-single,pins = < J721S2_IOPAD(0x104, PIN_INPUT, 0) /* (P23) MMC1_CLK */
@@ -356,6 +363,24 @@ exp2: gpio@22 { }; }; +&main_i2c5 { + pinctrl-names = "default"; + pinctrl-0 = <&main_i2c5_pins_default>; + clock-frequency = <400000>; + status = "okay"; + + exp5: gpio@20 { + compatible = "ti,tca6408"; + reg = <0x20>; + gpio-controller; + #gpio-cells = <2>; + gpio-line-names = "CSI2_EXP_RSTZ", "CSI2_EXP_A_GPIO0", + "CSI2_EXP_A_GPIO1", "CSI2_EXP_A_GPIO2", + "CSI2_EXP_B_GPIO1", "CSI2_EXP_B_GPIO2", + "CSI2_EXP_B_GPIO3", "CSI2_EXP_B_GPIO4"; + }; +}; + &main_sdhci0 { /* eMMC */ status = "okay";
Signature · 1 line
2.34.1
PATCH v3 2/9 arm64: dts: ti: k3-j784s4-evm: Enable camera peripherals
In reply to Vaishnav AchathCSI cameras are controlled using I2C. On J784S4 EVM, this is routed to I2C-5, so enable the instance and the TCA6408 GPIO expander on the bus.
J784S4 EVM schematics: https://www.ti.com/lit/zip/sprr458
---
V1->V2: Update commit message with schematics.
arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 25 ++++++++++++++++++++++++ 1 file changed, 25 insertions(+)
arch/arm64/boot/dts/ti/k3-j784s4-evm.dts +25 -0
@@ -297,6 +297,13 @@ J784S4_IOPAD(0x0e4, PIN_INPUT_PULLUP, 0) /* (AP37) I2C0_SDA */ >; }; + main_i2c5_pins_default: main-i2c5-default-pins { + pinctrl-single,pins = < + J784S4_IOPAD(0x01c, PIN_INPUT, 8) /* (AG34) MCAN15_TX.I2C5_SCL */ + J784S4_IOPAD(0x018, PIN_INPUT, 8) /* (AK36) MCAN14_RX.I2C5_SDA */ + >; + }; + main_mmc1_pins_default: main-mmc1-default-pins { bootph-all; pinctrl-single,pins = <
@@ -761,6 +768,24 @@ exp2: gpio@22 { }; }; +&main_i2c5 { + pinctrl-names = "default"; + pinctrl-0 = <&main_i2c5_pins_default>; + clock-frequency = <400000>; + status = "okay"; + + exp5: gpio@20 { + compatible = "ti,tca6408"; + reg = <0x20>; + gpio-controller; + #gpio-cells = <2>; + gpio-line-names = "CSI2_EXP_RSTZ", "CSI2_EXP_A_GPIO0", + "CSI2_EXP_A_GPIO1", "CSI2_EXP_A_GPIO3", + "CSI2_EXP_B_GPIO1", "CSI2_EXP_B_GPIO2", + "CSI2_EXP_B_GPIO3", "CSI2_EXP_B_GPIO4"; + }; +}; + &main_sdhci0 { bootph-all; /* eMMC */
Signature · 1 line
2.34.1
PATCH v3 3/9 arm64: dts: ti: k3-am68-sk-base-board: Enable camera peripherals
In reply to Vaishnav AchathCSI cameras are controlled using I2C. On AM68 Starter Kit, this is routed to I2C-1, so enable the instance and the TCA9543 I2C switch on the bus.
AM68 SK schematics: https://www.ti.com/lit/zip/sprr463
---
V1->V2: Update commit message with schematics.
.../boot/dts/ti/k3-am68-sk-base-board.dts | 50 +++++++++++++++++++ 1 file changed, 50 insertions(+)
arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts +50 -0
@@ -169,6 +169,13 @@ tfp410_out: endpoint { }; }; }; + + csi_mux: mux-controller { + compatible = "gpio-mux"; + #mux-state-cells = <1>; + mux-gpios = <&exp3 1 GPIO_ACTIVE_HIGH>; + idle-state = <0>; + }; }; &main_pmx0 {
@@ -186,6 +193,13 @@ J721S2_IOPAD(0x0e4, PIN_INPUT, 0) /* (AE24) I2C0_SDA */ >; }; + main_i2c1_pins_default: main-i2c1-default-pins { + pinctrl-single,pins = < + J721S2_IOPAD(0x0ac, PIN_INPUT, 13) /* (AC25) MCASP0_AXR15.I2C1_SCL */ + J721S2_IOPAD(0x0b0, PIN_INPUT, 13) /* (AD26) MCASP1_AXR3.I2C1_SDA */ + >; + }; + main_mmc1_pins_default: main-mmc1-default-pins { pinctrl-single,pins = < J721S2_IOPAD(0x104, PIN_INPUT, 0) /* (P23) MMC1_CLK */
@@ -431,6 +445,42 @@ exp1: gpio@21 { }; }; +&main_i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&main_i2c1_pins_default>; + status = "okay"; + + exp3: gpio@20 { + compatible = "ti,tca6408"; + reg = <0x20>; + gpio-controller; + #gpio-cells = <2>; + gpio-line-names = "CSI_VIO_SEL", "CSI_SEL_FPC_EXPn", + "IO_EXP_CSI2_EXP_RSTz","CSI0_B_GPIO1", + "CSI1_B_GPIO1"; + }; + + i2c-mux@70 { + compatible = "nxp,pca9543"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x70>; + + cam0_i2c: i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + }; + + cam1_i2c: i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + }; + + }; +}; + &main_i2c4 { status = "okay"; pinctrl-names = "default";
Signature · 1 line
2.34.1
PATCH v3 4/9 arm64: dts: ti: k3-am69-sk: Enable camera peripherals
In reply to Vaishnav AchathCSI cameras are controlled using I2C. On AM69 Starter Kit, this is routed to I2C-1, so enable the instance, TCA9543 I2C switch and the TCA6408 GPIO expander on the bus. AM69 SK has the CSI2RX routed to a MIPI CSI connector and to 22-pin RPi camera connector through an analog mux with GPIO control, model that so that an overlay can control the mux state according to connected cameras.
AM69 SK schematics: https://www.ti.com/lit/zip/sprr466
---
V1->V2: Update commit message with schematics.
arch/arm64/boot/dts/ti/k3-am69-sk.dts | 51 +++++++++++++++++++++++++++ 1 file changed, 51 insertions(+)
arch/arm64/boot/dts/ti/k3-am69-sk.dts +51 -0
@@ -322,6 +322,14 @@ tfp410_out: endpoint { }; }; }; + + csi_mux: mux-controller { + compatible = "gpio-mux"; + #mux-state-cells = <1>; + mux-gpios = <&exp2 1 GPIO_ACTIVE_HIGH>; + idle-state = <0>; + }; + }; &main_pmx0 {
@@ -341,6 +349,13 @@ J784S4_IOPAD(0x0e4, PIN_INPUT_PULLUP, 0) /* (AP37) I2C0_SDA */ >; }; + main_i2c1_pins_default: main-i2c1-default-pins { + pinctrl-single,pins = < + J784S4_IOPAD(0x0ac, PIN_INPUT_PULLUP, 13) /* (AE34) MCASP0_AXR15.I2C1_SCL */ + J784S4_IOPAD(0x0b0, PIN_INPUT_PULLUP, 13) /* (AL33) MCASP1_AXR3.I2C1_SDA */ + >; + }; + main_mmc1_pins_default: main-mmc1-default-pins { bootph-all; pinctrl-single,pins = <
@@ -775,6 +790,42 @@ exp1: gpio@21 { }; }; +&main_i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&main_i2c1_pins_default>; + clock-frequency = <400000>; + status = "okay"; + + exp2: gpio@21 { + compatible = "ti,tca6408"; + reg = <0x21>; + gpio-controller; + #gpio-cells = <2>; + gpio-line-names = "CSI_VIO_SEL", "CSI_MUX_SEL_2", "CSI2_RSTz", + "IO_EXP_CAM0_GPIO1", "IO_EXP_CAM1_GPIO1"; + }; + + i2c-mux@70 { + compatible = "nxp,pca9543"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x70>; + + cam0_i2c: i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + }; + + cam1_i2c: i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + }; + + }; +}; + &main_sdhci0 { bootph-all; /* eMMC */
Signature · 1 line
2.34.1
PATCH v3 5/9 arm64: dts: ti: k3-j721e-sk: Model CSI2RX connector mux
In reply to Vaishnav AchathJ721E SK has the CSI2RX routed to a MIPI CSI connector and to 15-pin RPi camera connector through an analog mux with GPIO control, model that so that an overlay can control the mux state according to connected cameras. Also provide labels to the I2C mux bus instances so that a generic overlay can be used across multiple platforms.
J721E SK schematics: https://www.ti.com/lit/zip/sprr438
---
V1->V2: Update commit message with schematics.
arch/arm64/boot/dts/ti/k3-j721e-sk.dts | 19 +++++++++++++++++-- 1 file changed, 17 insertions(+), 2 deletions(-)
arch/arm64/boot/dts/ti/k3-j721e-sk.dts +17 -2
@@ -286,6 +286,15 @@ tfp410_out: endpoint { }; }; }; + + csi_mux: mux-controller { + compatible = "gpio-mux"; + #mux-state-cells = <1>; + mux-gpios = <&main_gpio0 88 GPIO_ACTIVE_HIGH>; + idle-state = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&main_csi_mux_sel_pins_default>; + }; }; &main_pmx0 {
@@ -352,6 +361,12 @@ J721E_IOPAD(0x214, PIN_OUTPUT, 4) /* (V4) MCAN1_TX.USB1_DRVVBUS */ >; }; + main_csi_mux_sel_pins_default: main-csi-mux-sel-default-pins { + pinctrl-single,pins = < + J721E_IOPAD(0x164, PIN_OUTPUT, 7) /* (V29) RGMII5_TD2 */ + >; + }; + dp0_pins_default: dp0-default-pins { pinctrl-single,pins = < J721E_IOPAD(0x1c4, PIN_INPUT, 5) /* SPI0_CS1.DP0_HPD */
@@ -858,14 +873,14 @@ i2c-mux@70 { reg = <0x70>; /* CSI0 I2C */ - i2c@0 { + cam0_i2c: i2c@0 { #address-cells = <1>; #size-cells = <0>; reg = <0>; }; /* CSI1 I2C */ - i2c@1 { + cam1_i2c: i2c@1 { #address-cells = <1>; #size-cells = <0>; reg = <1>;
Signature · 1 line
2.34.1
PATCH v3 6/9 arm64: dts: ti: k3-j721e-main: Add CSI2RX capture nodes
In reply to Vaishnav AchathJ721E has two CSI2RX capture subsystem featuring Cadence CSI2RX, DPHY and TI's pixel grabbing wrapper. Add nodes for the same and keep them disabled by default.
J721E TRM (Section 12.7 Camera Subsystem):
https://www.ti.com/lit/zip/spruil1
---
V2->V3: Fix order of properties as per dts coding style. V1->V2: Update commit message with TRM.
arch/arm64/boot/dts/ti/k3-j721e-main.dtsi | 122 ++++++++++++++++++++++ 1 file changed, 122 insertions(+)
arch/arm64/boot/dts/ti/k3-j721e-main.dtsi +122 -0
@@ -572,6 +572,128 @@ main_timerio_output: pinctrl@104280 { pinctrl-single,function-mask = <0x0000001f>; }; + ti_csi2rx0: ticsi2rx@4500000 { + compatible = "ti,j721e-csi2rx-shim"; + reg = <0x0 0x4500000 0x0 0x1000>; + ranges; + #address-cells = <2>; + #size-cells = <2>; + dmas = <&main_udmap 0x4940>; + dma-names = "rx0"; + power-domains = <&k3_pds 26 TI_SCI_PD_EXCLUSIVE>; + status = "disabled"; + + cdns_csi2rx0: csi-bridge@4504000 { + compatible = "ti,j721e-csi2rx", "cdns,csi2rx"; + reg = <0x0 0x4504000 0x0 0x1000>; + clocks = <&k3_clks 26 2>, <&k3_clks 26 0>, <&k3_clks 26 2>, + <&k3_clks 26 2>, <&k3_clks 26 3>, <&k3_clks 26 3>; + clock-names = "sys_clk", "p_clk", "pixel_if0_clk", + "pixel_if1_clk", "pixel_if2_clk", "pixel_if3_clk"; + phys = <&dphy0>; + phy-names = "dphy"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + csi0_port0: port@0 { + reg = <0>; + status = "disabled"; + }; + + csi0_port1: port@1 { + reg = <1>; + status = "disabled"; + }; + + csi0_port2: port@2 { + reg = <2>; + status = "disabled"; + }; + + csi0_port3: port@3 { + reg = <3>; + status = "disabled"; + }; + + csi0_port4: port@4 { + reg = <4>; + status = "disabled"; + }; + }; + }; + }; + + ti_csi2rx1: ticsi2rx@4510000 { + compatible = "ti,j721e-csi2rx-shim"; + reg = <0x0 0x4510000 0x0 0x1000>; + ranges; + #address-cells = <2>; + #size-cells = <2>; + dmas = <&main_udmap 0x4960>; + dma-names = "rx0"; + power-domains = <&k3_pds 27 TI_SCI_PD_EXCLUSIVE>; + status = "disabled"; + + cdns_csi2rx1: csi-bridge@4514000 { + compatible = "ti,j721e-csi2rx", "cdns,csi2rx"; + reg = <0x0 0x4514000 0x0 0x1000>; + clocks = <&k3_clks 27 2>, <&k3_clks 27 0>, <&k3_clks 27 2>, + <&k3_clks 27 2>, <&k3_clks 27 3>, <&k3_clks 27 3>; + clock-names = "sys_clk", "p_clk", "pixel_if0_clk", + "pixel_if1_clk", "pixel_if2_clk", "pixel_if3_clk"; + phys = <&dphy1>; + phy-names = "dphy"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + csi1_port0: port@0 { + reg = <0>; + status = "disabled"; + }; + + csi1_port1: port@1 { + reg = <1>; + status = "disabled"; + }; + + csi1_port2: port@2 { + reg = <2>; + status = "disabled"; + }; + + csi1_port3: port@3 { + reg = <3>; + status = "disabled"; + }; + + csi1_port4: port@4 { + reg = <4>; + status = "disabled"; + }; + }; + }; + }; + + dphy0: phy@4580000 { + compatible = "cdns,dphy-rx"; + reg = <0x0 0x4580000 0x0 0x1100>; + #phy-cells = <0>; + power-domains = <&k3_pds 147 TI_SCI_PD_EXCLUSIVE>; + status = "disabled"; + }; + + dphy1: phy@4590000 { + compatible = "cdns,dphy-rx"; + reg = <0x0 0x4590000 0x0 0x1100>; + #phy-cells = <0>; + power-domains = <&k3_pds 148 TI_SCI_PD_EXCLUSIVE>; + status = "disabled"; + }; + serdes_wiz0: wiz@5000000 { compatible = "ti,j721e-wiz-16g"; #address-cells = <1>;
Signature · 1 line
2.34.1
Re: [PATCH v3 6/9] arm64: dts: ti: k3-j721e-main: Add CSI2RX capture nodes
Quoted 8 lines · Vaishnav Achath
J721E has two CSI2RX capture subsystem featuring Cadence CSI2RX, DPHY and TI's pixel grabbing wrapper. Add nodes for the same and keep them disabled by default.
J721E TRM (Section 12.7 Camera Subsystem):
https://www.ti.com/lit/zip/spruil1Signed-off-by Vaishnav Achath <[email protected]>
Quoted 9 lines
---
V2->V3: Fix order of properties as per dts coding style.V1->V2: Update commit message with TRM.arch/arm64/boot/dts/ti/k3-j721e-main.dtsi | 122 ++++++++++++++++++++++ 1 file changed, 122 insertions(+)[...]
Signature · 4 lines
Thanks, Jai GPG Fingerprint: 4DE0 D818 E5D5 75E8 D45A AFC5 43DE 91F9 249A 7145
PATCH v3 7/9 arm64: dts: ti: k3-j721s2-main: Add CSI2RX capture nodes
In reply to Vaishnav AchathJ721S2 has two CSI2RX capture subsystem featuring Cadence CSI2RX, DPHY and TI's pixel grabbing wrapper. Add nodes for the same and keep them disabled by default. J721S2 uses a dedicated BCDMA instance for CSI-RX traffic, so enable that as well.
J721S2 TRM (Section 12.7 Camera Subsystem):
https://www.ti.com/lit/zip/spruj28
---
V2->V3: Fix order of properties as per dts coding style. V1->V2: Update commit message with TRM.
arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi | 123 ++++++++++++++++++++- 1 file changed, 122 insertions(+), 1 deletion(-)
arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi +122 -1
@@ -1122,7 +1122,6 @@ main_bcdma_csi: dma-controller@311a0000 { ti,sci-dev-id = <225>; ti,sci-rm-range-rchan = <0x21>; ti,sci-rm-range-tchan = <0x22>; - status = "disabled"; }; cpts@310d0000 {
@@ -1233,6 +1232,128 @@ usb0: usb@6000000 { }; }; + ti_csi2rx0: ticsi2rx@4500000 { + compatible = "ti,j721e-csi2rx-shim"; + reg = <0x00 0x04500000 0x00 0x1000>; + ranges; + #address-cells = <2>; + #size-cells = <2>; + dmas = <&main_bcdma_csi 0 0x4940 0>; + dma-names = "rx0"; + power-domains = <&k3_pds 38 TI_SCI_PD_EXCLUSIVE>; + status = "disabled"; + + cdns_csi2rx0: csi-bridge@4504000 { + compatible = "ti,j721e-csi2rx", "cdns,csi2rx"; + reg = <0x00 0x04504000 0x00 0x1000>; + clocks = <&k3_clks 38 3>, <&k3_clks 38 1>, <&k3_clks 38 3>, + <&k3_clks 38 3>, <&k3_clks 38 4>, <&k3_clks 38 4>; + clock-names = "sys_clk", "p_clk", "pixel_if0_clk", + "pixel_if1_clk", "pixel_if2_clk", "pixel_if3_clk"; + phys = <&dphy0>; + phy-names = "dphy"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + csi0_port0: port@0 { + reg = <0>; + status = "disabled"; + }; + + csi0_port1: port@1 { + reg = <1>; + status = "disabled"; + }; + + csi0_port2: port@2 { + reg = <2>; + status = "disabled"; + }; + + csi0_port3: port@3 { + reg = <3>; + status = "disabled"; + }; + + csi0_port4: port@4 { + reg = <4>; + status = "disabled"; + }; + }; + }; + }; + + ti_csi2rx1: ticsi2rx@4510000 { + compatible = "ti,j721e-csi2rx-shim"; + reg = <0x00 0x04510000 0x00 0x1000>; + ranges; + #address-cells = <2>; + #size-cells = <2>; + dmas = <&main_bcdma_csi 0 0x4960 0>; + dma-names = "rx0"; + power-domains = <&k3_pds 39 TI_SCI_PD_EXCLUSIVE>; + status = "disabled"; + + cdns_csi2rx1: csi-bridge@4514000 { + compatible = "ti,j721e-csi2rx", "cdns,csi2rx"; + reg = <0x00 0x04514000 0x00 0x1000>; + clocks = <&k3_clks 39 3>, <&k3_clks 39 1>, <&k3_clks 39 3>, + <&k3_clks 39 3>, <&k3_clks 39 4>, <&k3_clks 39 4>; + clock-names = "sys_clk", "p_clk", "pixel_if0_clk", + "pixel_if1_clk", "pixel_if2_clk", "pixel_if3_clk"; + phys = <&dphy1>; + phy-names = "dphy"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + csi1_port0: port@0 { + reg = <0>; + status = "disabled"; + }; + + csi1_port1: port@1 { + reg = <1>; + status = "disabled"; + }; + + csi1_port2: port@2 { + reg = <2>; + status = "disabled"; + }; + + csi1_port3: port@3 { + reg = <3>; + status = "disabled"; + }; + + csi1_port4: port@4 { + reg = <4>; + status = "disabled"; + }; + }; + }; + }; + + dphy0: phy@4580000 { + compatible = "cdns,dphy-rx"; + reg = <0x00 0x04580000 0x00 0x1100>; + #phy-cells = <0>; + power-domains = <&k3_pds 152 TI_SCI_PD_EXCLUSIVE>; + status = "disabled"; + }; + + dphy1: phy@4590000 { + compatible = "cdns,dphy-rx"; + reg = <0x00 0x04590000 0x00 0x1100>; + #phy-cells = <0>; + power-domains = <&k3_pds 153 TI_SCI_PD_EXCLUSIVE>; + status = "disabled"; + }; + serdes_wiz0: wiz@5060000 { compatible = "ti,j721s2-wiz-10g"; #address-cells = <1>;
Signature · 1 line
2.34.1
Re: [PATCH v3 7/9] arm64: dts: ti: k3-j721s2-main: Add CSI2RX capture nodes
Quoted 9 lines · Vaishnav Achath
J721S2 has two CSI2RX capture subsystem featuring Cadence CSI2RX, DPHY and TI's pixel grabbing wrapper. Add nodes for the same and keep them disabled by default. J721S2 uses a dedicated BCDMA instance for CSI-RX traffic, so enable that as well.
J721S2 TRM (Section 12.7 Camera Subsystem):
https://www.ti.com/lit/zip/spruj28Signed-off-by Vaishnav Achath <[email protected]>
Quoted 9 lines
---
V2->V3: Fix order of properties as per dts coding style.V1->V2: Update commit message with TRM.arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi | 123 ++++++++++++++++++++- 1 file changed, 122 insertions(+), 1 deletion(-)[...]
Signature · 4 lines
Thanks, Jai GPG Fingerprint: 4DE0 D818 E5D5 75E8 D45A AFC5 43DE 91F9 249A 7145
PATCH v3 8/9 arm64: dts: ti: k3-j784s4-main: Add CSI2RX capture nodes
In reply to Vaishnav AchathJ784S4 has three CSI2RX capture subsystem featuring Cadence CSI2RX, DPHY and TI's pixel grabbing wrapper. Add nodes for the same and keep them disabled by default. J784S4 uses a dedicated BCDMA instance for CSI-RX traffic, so enable that as well.
J784S4 TRM (Section 12.7 Camera Subsystem):
https://www.ti.com/lit/zip/spruj52
---
V2->V3: Fix order of properties as per dts coding style. V1->V2: Update commit message with TRM.
arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi | 183 ++++++++++++++++++++- 1 file changed, 182 insertions(+), 1 deletion(-)
arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi +182 -1
@@ -662,6 +662,188 @@ main_i2c6: i2c@2060000 { status = "disabled"; }; + ti_csi2rx0: ticsi2rx@4500000 { + compatible = "ti,j721e-csi2rx-shim"; + reg = <0x00 0x04500000 0x00 0x00001000>; + ranges; + #address-cells = <2>; + #size-cells = <2>; + dmas = <&main_bcdma_csi 0 0x4940 0>; + dma-names = "rx0"; + power-domains = <&k3_pds 72 TI_SCI_PD_EXCLUSIVE>; + status = "disabled"; + + cdns_csi2rx0: csi-bridge@4504000 { + compatible = "ti,j721e-csi2rx", "cdns,csi2rx"; + reg = <0x00 0x04504000 0x00 0x00001000>; + clocks = <&k3_clks 72 2>, <&k3_clks 72 0>, <&k3_clks 72 2>, + <&k3_clks 72 2>, <&k3_clks 72 3>, <&k3_clks 72 3>; + clock-names = "sys_clk", "p_clk", "pixel_if0_clk", + "pixel_if1_clk", "pixel_if2_clk", "pixel_if3_clk"; + phys = <&dphy0>; + phy-names = "dphy"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + csi0_port0: port@0 { + reg = <0>; + status = "disabled"; + }; + + csi0_port1: port@1 { + reg = <1>; + status = "disabled"; + }; + + csi0_port2: port@2 { + reg = <2>; + status = "disabled"; + }; + + csi0_port3: port@3 { + reg = <3>; + status = "disabled"; + }; + + csi0_port4: port@4 { + reg = <4>; + status = "disabled"; + }; + }; + }; + }; + + ti_csi2rx1: ticsi2rx@4510000 { + compatible = "ti,j721e-csi2rx-shim"; + reg = <0x00 0x04510000 0x00 0x1000>; + ranges; + #address-cells = <2>; + #size-cells = <2>; + dmas = <&main_bcdma_csi 0 0x4960 0>; + dma-names = "rx0"; + power-domains = <&k3_pds 73 TI_SCI_PD_EXCLUSIVE>; + status = "disabled"; + + cdns_csi2rx1: csi-bridge@4514000 { + compatible = "ti,j721e-csi2rx", "cdns,csi2rx"; + reg = <0x00 0x04514000 0x00 0x00001000>; + clocks = <&k3_clks 73 2>, <&k3_clks 73 0>, <&k3_clks 73 2>, + <&k3_clks 73 2>, <&k3_clks 73 3>, <&k3_clks 73 3>; + clock-names = "sys_clk", "p_clk", "pixel_if0_clk", + "pixel_if1_clk", "pixel_if2_clk", "pixel_if3_clk"; + phys = <&dphy1>; + phy-names = "dphy"; + ports { + #address-cells = <1>; + #size-cells = <0>; + + csi1_port0: port@0 { + reg = <0>; + status = "disabled"; + }; + + csi1_port1: port@1 { + reg = <1>; + status = "disabled"; + }; + + csi1_port2: port@2 { + reg = <2>; + status = "disabled"; + }; + + csi1_port3: port@3 { + reg = <3>; + status = "disabled"; + }; + + csi1_port4: port@4 { + reg = <4>; + status = "disabled"; + }; + }; + }; + }; + + ti_csi2rx2: ticsi2rx@4520000 { + compatible = "ti,j721e-csi2rx-shim"; + reg = <0x00 0x04520000 0x00 0x00001000>; + ranges; + #address-cells = <2>; + #size-cells = <2>; + dmas = <&main_bcdma_csi 0 0x4980 0>; + dma-names = "rx0"; + power-domains = <&k3_pds 74 TI_SCI_PD_EXCLUSIVE>; + status = "disabled"; + + cdns_csi2rx2: csi-bridge@4524000 { + compatible = "ti,j721e-csi2rx", "cdns,csi2rx"; + reg = <0x00 0x04524000 0x00 0x00001000>; + clocks = <&k3_clks 74 2>, <&k3_clks 74 0>, <&k3_clks 74 2>, + <&k3_clks 74 2>, <&k3_clks 74 3>, <&k3_clks 74 3>; + clock-names = "sys_clk", "p_clk", "pixel_if0_clk", + "pixel_if1_clk", "pixel_if2_clk", "pixel_if3_clk"; + phys = <&dphy2>; + phy-names = "dphy"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + csi2_port0: port@0 { + reg = <0>; + status = "disabled"; + }; + + csi2_port1: port@1 { + reg = <1>; + status = "disabled"; + }; + + csi2_port2: port@2 { + reg = <2>; + status = "disabled"; + }; + + csi2_port3: port@3 { + reg = <3>; + status = "disabled"; + }; + + csi2_port4: port@4 { + reg = <4>; + status = "disabled"; + }; + }; + }; + }; + + dphy0: phy@4580000 { + compatible = "cdns,dphy-rx"; + reg = <0x00 0x04580000 0x00 0x00001100>; + #phy-cells = <0>; + power-domains = <&k3_pds 212 TI_SCI_PD_EXCLUSIVE>; + status = "disabled"; + }; + + dphy1: phy@4590000 { + compatible = "cdns,dphy-rx"; + reg = <0x00 0x04590000 0x00 0x00001100>; + #phy-cells = <0>; + power-domains = <&k3_pds 213 TI_SCI_PD_EXCLUSIVE>; + status = "disabled"; + }; + + dphy2: phy@45a0000 { + compatible = "cdns,dphy-rx"; + reg = <0x00 0x045a0000 0x00 0x00001100>; + #phy-cells = <0>; + power-domains = <&k3_pds 214 TI_SCI_PD_EXCLUSIVE>; + status = "disabled"; + }; + main_sdhci0: mmc@4f80000 { compatible = "ti,j721e-sdhci-8bit"; reg = <0x00 0x04f80000 0x00 0x1000>,
@@ -1224,7 +1406,6 @@ main_bcdma_csi: dma-controller@311a0000 { ti,sci-dev-id = <281>; ti,sci-rm-range-rchan = <0x21>; ti,sci-rm-range-tchan = <0x22>; - status = "disabled"; }; cpts@310d0000 {
Signature · 1 line
2.34.1
Re: [PATCH v3 8/9] arm64: dts: ti: k3-j784s4-main: Add CSI2RX capture nodes
Quoted 9 lines · Vaishnav Achath
J784S4 has three CSI2RX capture subsystem featuring Cadence CSI2RX, DPHY and TI's pixel grabbing wrapper. Add nodes for the same and keep them disabled by default. J784S4 uses a dedicated BCDMA instance for CSI-RX traffic, so enable that as well.
J784S4 TRM (Section 12.7 Camera Subsystem):
https://www.ti.com/lit/zip/spruj52Signed-off-by Vaishnav Achath <[email protected]>
Quoted 9 lines
---
V2->V3: Fix order of properties as per dts coding style.V1->V2: Update commit message with TRM.arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi | 183 ++++++++++++++++++++- 1 file changed, 182 insertions(+), 1 deletion(-)[...]
Signature · 4 lines
Thanks, Jai GPG Fingerprint: 4DE0 D818 E5D5 75E8 D45A AFC5 43DE 91F9 249A 7145
PATCH v3 9/9 arm64: dts: ti: k3-j721e-sk: Add overlay for IMX219
In reply to Vaishnav AchathRPi v2 Camera (IMX219) is an 8MP camera that can be used with SK-AM69, J721E SK, and AM68 SK through the 22-pin CSI-RX connector.
Add a reference overlay for dual IMX219 RPI camera v2 modules which can be used across AM68 SK, AM69 SK, TDA4VM SK boards that have a 15/22-pin FFC connector. Also enable build testing and symbols for all the three platforms.
---
V1->V2:
* Rename overlays to indicate first platform (j721e-sk) supported and dual camera.
* Add missed build test, fix missing newline.
arch/arm64/boot/dts/ti/Makefile | 13 ++ .../dts/ti/k3-j721e-sk-csi2-dual-imx219.dtso | 125 ++++++++++++++++++ 2 files changed, 138 insertions(+) create mode 100644 arch/arm64/boot/dts/ti/k3-j721e-sk-csi2-dual-imx219.dtso
arch/arm64/boot/dts/ti/Makefile +13 -0
@@ -69,6 +69,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-j721e-evm.dtb dtb-$(CONFIG_ARCH_K3) += k3-j721e-evm-gesi-exp-board.dtbo dtb-$(CONFIG_ARCH_K3) += k3-j721e-evm-pcie0-ep.dtbo dtb-$(CONFIG_ARCH_K3) += k3-j721e-sk.dtb +dtb-$(CONFIG_ARCH_K3) += k3-j721e-sk-csi2-dual-imx219.dtbo # Boards with J721s2 SoC dtb-$(CONFIG_ARCH_K3) += k3-am68-sk-base-board.dtb
@@ -106,8 +107,14 @@ k3-am642-tqma64xxl-mbax4xxl-sdcard-dtbs := \ k3-am642-tqma64xxl-mbax4xxl.dtb k3-am64-tqma64xxl-mbax4xxl-sdcard.dtbo k3-am642-tqma64xxl-mbax4xxl-wlan-dtbs := \ k3-am642-tqma64xxl-mbax4xxl.dtb k3-am64-tqma64xxl-mbax4xxl-wlan.dtbo +k3-am68-sk-base-board-csi2-dual-imx219-dtbs := k3-am68-sk-base-board.dtb \ + k3-j721e-sk-csi2-dual-imx219.dtbo +k3-am69-sk-csi2-dual-imx219-dtbs := k3-am69-sk.dtb \ + k3-j721e-sk-csi2-dual-imx219.dtbo k3-j721e-evm-pcie0-ep-dtbs := k3-j721e-common-proc-board.dtb \ k3-j721e-evm-pcie0-ep.dtbo +k3-j721e-sk-csi2-dual-imx219-dtbs := k3-j721e-sk.dtb \ + k3-j721e-sk-csi2-dual-imx219.dtbo k3-j721s2-evm-pcie1-ep-dtbs := k3-j721s2-common-proc-board.dtb \ k3-j721s2-evm-pcie1-ep.dtbo dtb- += k3-am625-beagleplay-csi2-ov5640.dtb \
@@ -122,7 +129,10 @@ dtb- += k3-am625-beagleplay-csi2-ov5640.dtb \ k3-am62a7-sk-hdmi-audio.dtb \ k3-am642-tqma64xxl-mbax4xxl-sdcard.dtb \ k3-am642-tqma64xxl-mbax4xxl-wlan.dtb \ + k3-am68-sk-base-board-csi2-dual-imx219-dtbs \ + k3-am69-sk-csi2-dual-imx219-dtbs \ k3-j721e-evm-pcie0-ep.dtb \ + k3-j721e-sk-csi2-dual-imx219-dtbs \ k3-j721s2-evm-pcie1-ep.dtb # Enable support for device-tree overlays
@@ -132,5 +142,8 @@ DTC_FLAGS_k3-am62-lp-sk += -@ DTC_FLAGS_k3-am62a7-sk += -@ DTC_FLAGS_k3-am642-tqma64xxl-mbax4xxl += -@ DTC_FLAGS_k3-am6548-iot2050-advanced-m2 += -@ +DTC_FLAGS_k3-am68-sk-base-board += -@ +DTC_FLAGS_k3-am69-sk += -@ DTC_FLAGS_k3-j721e-common-proc-board += -@ +DTC_FLAGS_k3-j721e-sk += -@ DTC_FLAGS_k3-j721s2-common-proc-board += -@
arch/arm64/boot/dts/ti/k3-j721e-sk-csi2-dual-imx219.dtso new file +125 -0
125 lines not on this page · raw message
Signature · 1 line
2.34.1