hwmon: (pmbus/mp2975) Fix IRQ masking
PATCH v2 1/1 hwmon: (pmbus/mp2975) Fix IRQ masking
From: Patrick Rudolph <[email protected]>
The MP2971/MP2973 use a custom 16bit register format for SMBALERT_MASK which doesn't follow the PMBUS specification.
Map the PMBUS defined bits used by the common code onto the custom format used by MPS and since the SMBALERT_MASK is currently never read by common code only implement the mapping for write transactions.
--- drivers/hwmon/pmbus/mp2975.c | 77 ++++++++++++++++++++++++++++++++++++ 1 file changed, 77 insertions(+)
drivers/hwmon/pmbus/mp2975.c +77 -0
@@ -392,6 +392,82 @@ static int mp2973_read_word_data(struct i2c_client *client, int page,return ret; } +static int mp2973_write_word_data (struct i2c_client *client,int page, +int reg,u16 word) +{ +u8 target, mask; +int ret; + +if (reg !=PMBUS_SMBALERT_MASK ) +return -ENODATA ; + +/* +* Vendor-specific SMBALERT_MASK register with 16 maskable bits. +*/ + ret =pmbus_read_word_data (client,0 ,0 ,PMBUS_SMBALERT_MASK ); +if (ret <0 ) +return ret; + + target = word &0xff ; + mask = word >>8 ; + +/* +* Set/Clear 'bit' in 'ret' based on condition followed by define for each bit in SMBALERT_MASK. +* Also bit 2 & 15 are reserved. +*/ +#define SWAP (cond, bit) (ret = (mask & cond) ? (ret & ~BIT(bit)) : (ret | BIT(bit))) + +#define MP2973_TEMP_OT 0 +#define MP2973_VIN_UVLO 1 +#define MP2973_VIN_OVP 3 +#define MP2973_MTP_FAULT 4 +#define MP2973_OTHER_COMM 5 +#define MP2973_MTP_BLK_TRIG 6 +#define MP2973_PACKET_ERROR 7 +#define MP2973_INVALID_DATA 8 +#define MP2973_INVALID_COMMAND 9 +#define MP2973_IOUT_OC_LV 10 +#define MP2973_IOUT_OC 11 +#define MP2973_VOUT_MAX_MIN_WARNING 12 +#define MP2973_VOLTAGE_UV 13 +#define MP2973_VOLTAGE_OV 14 + +switch (target) { +case PMBUS_STATUS_CML : +SWAP (PB_CML_FAULT_INVALID_DATA ,MP2973_INVALID_DATA ); +SWAP (PB_CML_FAULT_INVALID_COMMAND ,MP2973_INVALID_COMMAND ); +SWAP (PB_CML_FAULT_OTHER_COMM ,MP2973_OTHER_COMM ); +SWAP (PB_CML_FAULT_PACKET_ERROR ,MP2973_PACKET_ERROR ); +break ; +case PMBUS_STATUS_VOUT : +SWAP (PB_VOLTAGE_UV_FAULT ,MP2973_VOLTAGE_UV ); +SWAP (PB_VOLTAGE_OV_FAULT ,MP2973_VOLTAGE_OV ); +break ; +case PMBUS_STATUS_IOUT : +SWAP (PB_IOUT_OC_FAULT ,MP2973_IOUT_OC ); +SWAP (PB_IOUT_OC_LV_FAULT ,MP2973_IOUT_OC_LV ); +break ; +case PMBUS_STATUS_TEMPERATURE : +SWAP (PB_TEMP_OT_FAULT ,MP2973_TEMP_OT ); +break ; +/* +* Map remaining bits to MFR specific to let the PMBUS core mask +* those bits by default. +*/ +case PMBUS_STATUS_MFR_SPECIFIC : +SWAP (BIT (1 ),MP2973_VIN_UVLO ); +SWAP (BIT (3 ),MP2973_VIN_OVP ); +SWAP (BIT (4 ),MP2973_MTP_FAULT ); +SWAP (BIT (6 ),MP2973_MTP_BLK_TRIG ); +break ; +default : +return 0 ; + } +#undef SWAP + +return pmbus_write_word_data (client,0 ,PMBUS_SMBALERT_MASK , ret); +} +static int mp2975_read_word_data (struct i2c_client *client,int page,int phase,int reg) {
@@ -907,6 +983,7 @@ static struct pmbus_driver_info mp2973_info = {PMBUS_HAVE_TEMP |PMBUS_HAVE_STATUS_TEMP |PMBUS_HAVE_POUT | PMBUS_HAVE_PIN | PMBUS_HAVE_STATUS_INPUT, .read_word_data = mp2973_read_word_data, + .write_word_data = mp2973_write_word_data, #if IS_ENABLED(CONFIG_SENSORS_MP2975_REGULATOR) .num_regulators =1 , .reg_desc = mp2975_reg_desc,
base-commit: 90d35da658da8cff0d4ecbb5113f5fac9d00eb72
Signature · 1 line
2.42.0
Guenter Roeck
maintainerQuoted 5 lines · Naresh Solanki
From: Patrick Rudolph <[email protected]>
The MP2971/MP2973 use a custom 16bit register format for
SMBALERT_MASKwhich doesn't follow the PMBUS specification.
Quoted 7 lines
Map the PMBUS defined bits used by the common code onto the custom format used by MPS and since the
SMBALERT_MASKis currently never read by common code only implement the mapping for write transactions.Signed-off-by Patrick Rudolph <[email protected]>Signed-off-by Naresh Solanki <[email protected]>---
What will it take for people to start providing change logs ? Why is that do difficult, and why do people seem to assume that I have the time to look up old e-mail chains ?
I'll have to write some boilerplate reply. Until I get to do that, I'll simply ignore patches without change logs (which I will do once I have the boilerplate as well, only then it will look nicer).
Guenter
Hi Guenter
Quoted 15 lines · Guenter Roeck
Quoted 5 lines · Naresh Solanki
From: Patrick Rudolph <[email protected]>
The MP2971/MP2973 use a custom 16bit register format for
SMBALERT_MASKwhich doesn't follow the PMBUS specification.Quoted 7 lines
Map the PMBUS defined bits used by the common code onto the custom format used by MPS and since the
SMBALERT_MASKis currently never read by common code only implement the mapping for write transactions.Signed-off-by Patrick Rudolph <[email protected]>Signed-off-by Naresh Solanki <[email protected]>---
Quoted 7 lines
What will it take for people to start providing change logs ? Why is that do difficult, and why do people seem to assume that I have the time to look up old e-mail chains ?
I'll have to write some boilerplate reply. Until I get to do that, I'll simply ignore patches without change logs (which I will do once I have the boilerplate as well, only then it will look nicer).
Yes I understand change log is very important. I missed adding that. Will resend the patch with change logs.
Regards,
Naresh.
Quoted 3 lines
Guenter