Replace sshd_config patching by snippets
cover Replace sshd_config patching by snippets
To deal with system setups, sshd was configured in the following way:
- sshd_config is shipped completely by OE and DISTRO_FEATURES (pam, x11) are patched in during do_install
--> this is difficulty to maintain; e.g. sshd_config must be
synchronized between OpenSSH releases and OE adaptations manually inserted
- two different configuration files (sshd_config + sshd_config_readonly) are created; IMAGE_FEATURES decides which one is used and it is patched in a ROOTFS_COMMAND in the system
--> this make it difficult for third party recipes to incorporate
their changes (they have to go over both files)
--> the readonly HostKey locations and algorithms are hardcoded
which makes it difficult to place them e.g. on a persistent /opt partition and disable e.g. ecdsa
- depending on IMAGE_FEATURES (empty passwords, root login), both files are patched by a ROOTFS_POSTCOMMAND
--> these changes are lost when pkgmgmt is used for the image and
openssh being updated
The patchset:
- reduces changes to sshd_config to
| Include /etc/ssh/sshd_config.d/*.conf
--> This is already the done in current recipe and most mainline
Linux distributions are doing it
- moves configuration in new openssh-config recipe which is a weak dependency of openssh (and can be replaced by another IMAGE_INSTALL)
Recipe ships configuration as small snippets which might contain dynamically created content (e.g. 'UsePAM yes')
- IMAGE_FEATURE based setup is done by creating subpackages with the corresponding options. These subpackages are added to FEATURE_PACKAGES_ssh-server-openssh
- readonly rootfs setup has been enhanced by
| RO_KEYDIR ??= "/var/run/ssh"
| KEY_ALGORITHMS ??= "rsa ecdsa ed25519"
parameters which can be overridden.
Enrico Scholz (7):
openssh: replace complete configuration files by patch
openssh-config: initial checkin
openssh: move configuration tweaking in configuration recipe
image: prepare openssh configuration
openssh: replace 'allow-empty-password' rootfs scipt by configuration
openssh: replace 'allow-root-login' rootfs scipt by configuration
openssh: move read-only-rootfs setup in configuration snippet
meta/classes-recipe/core-image.bbclass | 19 ++- .../rootfs-postcommands.bbclass | 25 +--- .../openssh/openssh-config.bb | 51 ++++++++ .../60-allow-empty-password.conf | 1 + .../openssh-config/60-allow-root-login.conf | 1 + .../openssh/openssh-config/80-oe.conf | 5 + .../openssh/openssh/include-conf.patch | 32 +++++ .../openssh/openssh/ssh_config | 48 ------- .../openssh/openssh/sshd_config | 119 ------------------ .../openssh/openssh_9.6p1.bb | 20 +-- 10 files changed, 112 insertions(+), 209 deletions(-) create mode 100644 meta/recipes-connectivity/openssh/openssh-config.bb create mode 100644 meta/recipes-connectivity/openssh/openssh-config/60-allow-empty-password.conf create mode 100644 meta/recipes-connectivity/openssh/openssh-config/60-allow-root-login.conf create mode 100644 meta/recipes-connectivity/openssh/openssh-config/80-oe.conf create mode 100644 meta/recipes-connectivity/openssh/openssh/include-conf.patch delete mode 100644 meta/recipes-connectivity/openssh/openssh/ssh_config delete mode 100644 meta/recipes-connectivity/openssh/openssh/sshd_config
Signature · 1 line
2.44.0
PATCH 1/7 openssh: replace complete configuration files by patch
From: Enrico Scholz <[email protected]>
Instead of shipping the whole configuration files for openssh, add small patch includes configuration snippets from subdirectories.
This allows us to keep the original upstream configuration which is mainly useful for documentation purposes. It makes it more easy to identify OE specific setup.
--- .../openssh/openssh/include-conf.patch | 32 +++++ .../openssh/openssh/ssh_config | 48 ------- .../openssh/openssh/sshd_config | 119 ------------------ .../openssh/openssh_9.6p1.bb | 5 +- 4 files changed, 33 insertions(+), 171 deletions(-) create mode 100644 meta/recipes-connectivity/openssh/openssh/include-conf.patch delete mode 100644 meta/recipes-connectivity/openssh/openssh/ssh_config delete mode 100644 meta/recipes-connectivity/openssh/openssh/sshd_config
meta/recipes-connectivity/openssh/openssh/include-conf.patch new file +32 -0
@@ -0,0 +1,32 @@ +Include configuration snippets from subdirectory. + +NOTE: first configuration option wins. + +Upstream-Status: Inappropriate + +Index: openssh-9.5p1/ssh_config +=================================================================== +--- openssh-9.5p1.orig/ssh_config ++++ openssh-9.5p1/ssh_config +@@ -5,6 +5,8 @@ + # users, and the values can be changed in per-user configuration files + # or on the command line. + ++Include /etc/ssh/ssh_config.d/*.conf ++ + # Configuration data is parsed as follows: + # 1. command line options + # 2. user-specific file +Index: openssh-9.5p1/sshd_config +=================================================================== +--- openssh-9.5p1.orig/sshd_config ++++ openssh-9.5p1/sshd_config +@@ -10,6 +10,8 @@ + # possible, but leave them commented. Uncommented options override the + # default value. + ++Include /etc/ssh/sshd_config.d/*.conf ++ + #Port 22 + #AddressFamily any + #ListenAddress 0.0.0.0
meta/recipes-connectivity/openssh/openssh/ssh_config deleted +0 -48
48 lines not on this page · raw message
meta/recipes-connectivity/openssh/openssh/sshd_config deleted +0 -119
119 lines not on this page · raw message
meta/recipes-connectivity/openssh/openssh_9.6p1.bb +1 -4
@@ -12,8 +12,6 @@ DEPENDS = "zlib openssl virtual/crypt" DEPENDS += "${@bb.utils.contains('DISTRO_FEATURES', 'pam', 'libpam', '', d)}" SRC_URI = "http://ftp.openbsd.org/pub/OpenBSD/OpenSSH/portable/openssh-${PV}.tar.gz \ - file://sshd_config \ - file://ssh_config \ file://init \ ${@bb.utils.contains('DISTRO_FEATURES', 'pam', '${PAM_SRC_URI}', '', d)} \ file://sshd.service \
@@ -23,6 +21,7 @@ SRC_URI = "http://ftp.openbsd.org/pub/OpenBSD/OpenSSH/portable/openssh-${PV}.tar file://volatiles.99_sshd \ file://run-ptest \ file://fix-potential-signed-overflow-in-pointer-arithmatic.patch \ + file://include-conf.patch \ file://sshd_check_keys \ file://add-test-support-for-busybox.patch \ file://0001-regress-banner.sh-log-input-and-output-files-on-erro.patch \
@@ -101,8 +100,6 @@ CACHED_CONFIGUREVARS += "ac_cv_header_maillock_h=no" do_configure:prepend () { export LD="${CC}" - install -m 0644 ${WORKDIR}/sshd_config ${B}/ - install -m 0644 ${WORKDIR}/ssh_config ${B}/ } do_compile_ptest() {
Signature · 1 line
2.44.0
Patchtest results for [PATCH 1/7] openssh: replace complete configuration files by patch
Thank you for your submission. Patchtest identified one or more issues with the patch. Please see the log below for more information:
---
Testing patch /home/patchtest/share/mboxes/1-7-openssh-replace-complete-configuration-files-by-patch.patch
FAIL: test Signed-off-by presence: A patch file has been added without a Signed-off-by tag: 'include-conf.patch' (test_patch.TestPatch.test_signed_off_by_presence)
FAIL: test Upstream-Status presence: Upstream-Status is Inappropriate, but no reason was provided (test_patch.TestPatch.test_upstream_status_presence_format)
PASS: pretest src uri left files (test_metadata.TestMetadata.pretest_src_uri_left_files)
PASS: test CVE check ignore (test_metadata.TestMetadata.test_cve_check_ignore)
PASS: test CVE tag format (test_patch.TestPatch.test_cve_tag_format)
PASS: test Signed-off-by presence (test_mbox.TestMbox.test_signed_off_by_presence)
PASS: test author valid (test_mbox.TestMbox.test_author_valid)
PASS: test commit message presence (test_mbox.TestMbox.test_commit_message_presence)
PASS: test lic files chksum modified not mentioned (test_metadata.TestMetadata.test_lic_files_chksum_modified_not_mentioned)
PASS: test max line length (test_metadata.TestMetadata.test_max_line_length)
PASS: test mbox format (test_mbox.TestMbox.test_mbox_format)
PASS: test non-AUH upgrade (test_mbox.TestMbox.test_non_auh_upgrade)
PASS: test shortlog format (test_mbox.TestMbox.test_shortlog_format)
PASS: test shortlog length (test_mbox.TestMbox.test_shortlog_length)
PASS: test src uri left files (test_metadata.TestMetadata.test_src_uri_left_files)
SKIP: pretest pylint: No python related patches, skipping test (test_python_pylint.PyLint.pretest_pylint)
SKIP: test bugzilla entry format: No bug ID found (test_mbox.TestMbox.test_bugzilla_entry_format)
SKIP: test lic files chksum presence: No added recipes, skipping test (test_metadata.TestMetadata.test_lic_files_chksum_presence)
SKIP: test license presence: No added recipes, skipping test (test_metadata.TestMetadata.test_license_presence)
SKIP: test pylint: No python related patches, skipping test (test_python_pylint.PyLint.test_pylint)
SKIP: test series merge on head: Merge test is disabled for now (test_mbox.TestMbox.test_series_merge_on_head)
SKIP: test summary presence: No added recipes, skipping test (test_metadata.TestMetadata.test_summary_presence)
SKIP: test target mailing list: Series merged, no reason to check other mailing lists (test_mbox.TestMbox.test_target_mailing_list)
---
Please address the issues identified and
submit a new revision of the patch, or alternatively, reply to this email with an explanation of why the patch should be accepted. If you believe these results are due to an error in patchtest, please submit a bug at https://bugzilla.yoctoproject.org/ (use the 'Patchtest' category under 'Yocto Project Subprojects'). For more information on specific failures, see: https://wiki.yoctoproject.org/wiki/Patchtest. Thank you!
PATCH v2 1/7 openssh: replace complete configuration files by patch
In reply to Enrico ScholzFrom: Enrico Scholz <[email protected]>
Instead of shipping the whole configuration files for openssh, add small patch includes configuration snippets from subdirectories.
This allows us to keep the original upstream configuration which is mainly useful for documentation purposes. It makes it more easy to identify OE specific setup.
--- .../openssh/openssh/include-conf.patch | 32 +++++ .../openssh/openssh/ssh_config | 48 ------- .../openssh/openssh/sshd_config | 119 ------------------ .../openssh/openssh_9.6p1.bb | 5 +- 4 files changed, 33 insertions(+), 171 deletions(-) create mode 100644 meta/recipes-connectivity/openssh/openssh/include-conf.patch delete mode 100644 meta/recipes-connectivity/openssh/openssh/ssh_config delete mode 100644 meta/recipes-connectivity/openssh/openssh/sshd_config
meta/recipes-connectivity/openssh/openssh/include-conf.patch new file +32 -0
@@ -0,0 +1,32 @@ +Include configuration snippets from subdirectory. + +NOTE: first configuration option wins. + +Upstream-Status: Inappropriate [configuration] + +Index: openssh-9.5p1/ssh_config +=================================================================== +--- openssh-9.5p1.orig/ssh_config ++++ openssh-9.5p1/ssh_config +@@ -5,6 +5,8 @@ + # users, and the values can be changed in per-user configuration files + # or on the command line. + ++Include /etc/ssh/ssh_config.d/*.conf ++ + # Configuration data is parsed as follows: + # 1. command line options + # 2. user-specific file +Index: openssh-9.5p1/sshd_config +=================================================================== +--- openssh-9.5p1.orig/sshd_config ++++ openssh-9.5p1/sshd_config +@@ -10,6 +10,8 @@ + # possible, but leave them commented. Uncommented options override the + # default value. + ++Include /etc/ssh/sshd_config.d/*.conf ++ + #Port 22 + #AddressFamily any + #ListenAddress 0.0.0.0
meta/recipes-connectivity/openssh/openssh/ssh_config deleted +0 -48
48 lines not on this page · raw message
meta/recipes-connectivity/openssh/openssh/sshd_config deleted +0 -119
119 lines not on this page · raw message
meta/recipes-connectivity/openssh/openssh_9.6p1.bb +1 -4
@@ -12,8 +12,6 @@ DEPENDS = "zlib openssl virtual/crypt" DEPENDS += "${@bb.utils.contains('DISTRO_FEATURES', 'pam', 'libpam', '', d)}" SRC_URI = "http://ftp.openbsd.org/pub/OpenBSD/OpenSSH/portable/openssh-${PV}.tar.gz \ - file://sshd_config \ - file://ssh_config \ file://init \ ${@bb.utils.contains('DISTRO_FEATURES', 'pam', '${PAM_SRC_URI}', '', d)} \ file://sshd.service \
@@ -23,6 +21,7 @@ SRC_URI = "http://ftp.openbsd.org/pub/OpenBSD/OpenSSH/portable/openssh-${PV}.tar file://volatiles.99_sshd \ file://run-ptest \ file://fix-potential-signed-overflow-in-pointer-arithmatic.patch \ + file://include-conf.patch \ file://sshd_check_keys \ file://add-test-support-for-busybox.patch \ file://0001-regress-banner.sh-log-input-and-output-files-on-erro.patch \
@@ -101,8 +100,6 @@ CACHED_CONFIGUREVARS += "ac_cv_header_maillock_h=no" do_configure:prepend () { export LD="${CC}" - install -m 0644 ${WORKDIR}/sshd_config ${B}/ - install -m 0644 ${WORKDIR}/ssh_config ${B}/ } do_compile_ptest() {
Signature · 1 line
2.44.0
Patchtest results for [PATCH 1/7, v2] openssh: replace complete configuration files by patch
Thank you for your submission. Patchtest identified one or more issues with the patch. Please see the log below for more information:
---
Testing patch /home/patchtest/share/mboxes/1-7-v2-openssh-replace-complete-configuration-files-by-patch.patch
FAIL: test Signed-off-by presence: A patch file has been added without a Signed-off-by tag: 'include-conf.patch' (test_patch.TestPatch.test_signed_off_by_presence)
PASS: pretest src uri left files (test_metadata.TestMetadata.pretest_src_uri_left_files)
PASS: test CVE check ignore (test_metadata.TestMetadata.test_cve_check_ignore)
PASS: test CVE tag format (test_patch.TestPatch.test_cve_tag_format)
PASS: test Signed-off-by presence (test_mbox.TestMbox.test_signed_off_by_presence)
PASS: test Upstream-Status presence (test_patch.TestPatch.test_upstream_status_presence_format)
PASS: test author valid (test_mbox.TestMbox.test_author_valid)
PASS: test commit message presence (test_mbox.TestMbox.test_commit_message_presence)
PASS: test lic files chksum modified not mentioned (test_metadata.TestMetadata.test_lic_files_chksum_modified_not_mentioned)
PASS: test max line length (test_metadata.TestMetadata.test_max_line_length)
PASS: test mbox format (test_mbox.TestMbox.test_mbox_format)
PASS: test non-AUH upgrade (test_mbox.TestMbox.test_non_auh_upgrade)
PASS: test shortlog format (test_mbox.TestMbox.test_shortlog_format)
PASS: test shortlog length (test_mbox.TestMbox.test_shortlog_length)
PASS: test src uri left files (test_metadata.TestMetadata.test_src_uri_left_files)
SKIP: pretest pylint: No python related patches, skipping test (test_python_pylint.PyLint.pretest_pylint)
SKIP: test bugzilla entry format: No bug ID found (test_mbox.TestMbox.test_bugzilla_entry_format)
SKIP: test lic files chksum presence: No added recipes, skipping test (test_metadata.TestMetadata.test_lic_files_chksum_presence)
SKIP: test license presence: No added recipes, skipping test (test_metadata.TestMetadata.test_license_presence)
SKIP: test pylint: No python related patches, skipping test (test_python_pylint.PyLint.test_pylint)
SKIP: test series merge on head: Merge test is disabled for now (test_mbox.TestMbox.test_series_merge_on_head)
SKIP: test summary presence: No added recipes, skipping test (test_metadata.TestMetadata.test_summary_presence)
SKIP: test target mailing list: Series merged, no reason to check other mailing lists (test_mbox.TestMbox.test_target_mailing_list)
---
Please address the issues identified and
submit a new revision of the patch, or alternatively, reply to this email with an explanation of why the patch should be accepted. If you believe these results are due to an error in patchtest, please submit a bug at https://bugzilla.yoctoproject.org/ (use the 'Patchtest' category under 'Yocto Project Subprojects'). For more information on specific failures, see: https://wiki.yoctoproject.org/wiki/Patchtest. Thank you!
PATCH v3 1/7 openssh: replace complete configuration files by patch
In reply to Enrico ScholzFrom: Enrico Scholz <[email protected]>
Instead of shipping the whole configuration files for openssh, add small patch includes configuration snippets from subdirectories.
This allows us to keep the original upstream configuration which is mainly useful for documentation purposes. It makes it more easy to identify OE specific setup.
--- .../openssh/openssh/include-conf.patch | 34 +++++ .../openssh/openssh/ssh_config | 48 ------- .../openssh/openssh/sshd_config | 119 ------------------ .../openssh/openssh_9.6p1.bb | 5 +- 4 files changed, 35 insertions(+), 171 deletions(-) create mode 100644 meta/recipes-connectivity/openssh/openssh/include-conf.patch delete mode 100644 meta/recipes-connectivity/openssh/openssh/ssh_config delete mode 100644 meta/recipes-connectivity/openssh/openssh/sshd_config
meta/recipes-connectivity/openssh/openssh/include-conf.patch new file +34 -0
@@ -0,0 +1,34 @@ +Include configuration snippets from subdirectory. + +NOTE: first configuration option wins. + +Upstream-Status: Inappropriate [configuration] + +Signed-off-by: Enrico Scholz <[email protected]> + +Index: openssh-9.5p1/ssh_config +=================================================================== +--- openssh-9.5p1.orig/ssh_config ++++ openssh-9.5p1/ssh_config +@@ -5,6 +5,8 @@ + # users, and the values can be changed in per-user configuration files + # or on the command line. + ++Include /etc/ssh/ssh_config.d/*.conf ++ + # Configuration data is parsed as follows: + # 1. command line options + # 2. user-specific file +Index: openssh-9.5p1/sshd_config +=================================================================== +--- openssh-9.5p1.orig/sshd_config ++++ openssh-9.5p1/sshd_config +@@ -10,6 +10,8 @@ + # possible, but leave them commented. Uncommented options override the + # default value. + ++Include /etc/ssh/sshd_config.d/*.conf ++ + #Port 22 + #AddressFamily any + #ListenAddress 0.0.0.0
meta/recipes-connectivity/openssh/openssh/ssh_config deleted +0 -48
48 lines not on this page · raw message
meta/recipes-connectivity/openssh/openssh/sshd_config deleted +0 -119
119 lines not on this page · raw message
meta/recipes-connectivity/openssh/openssh_9.6p1.bb +1 -4
@@ -12,8 +12,6 @@ DEPENDS = "zlib openssl virtual/crypt" DEPENDS += "${@bb.utils.contains('DISTRO_FEATURES', 'pam', 'libpam', '', d)}" SRC_URI = "http://ftp.openbsd.org/pub/OpenBSD/OpenSSH/portable/openssh-${PV}.tar.gz \ - file://sshd_config \ - file://ssh_config \ file://init \ ${@bb.utils.contains('DISTRO_FEATURES', 'pam', '${PAM_SRC_URI}', '', d)} \ file://sshd.service \
@@ -23,6 +21,7 @@ SRC_URI = "http://ftp.openbsd.org/pub/OpenBSD/OpenSSH/portable/openssh-${PV}.tar file://volatiles.99_sshd \ file://run-ptest \ file://fix-potential-signed-overflow-in-pointer-arithmatic.patch \ + file://include-conf.patch \ file://sshd_check_keys \ file://add-test-support-for-busybox.patch \ file://0001-regress-banner.sh-log-input-and-output-files-on-erro.patch \
@@ -101,8 +100,6 @@ CACHED_CONFIGUREVARS += "ac_cv_header_maillock_h=no" do_configure:prepend () { export LD="${CC}" - install -m 0644 ${WORKDIR}/sshd_config ${B}/ - install -m 0644 ${WORKDIR}/ssh_config ${B}/ } do_compile_ptest() {
Signature · 1 line
2.44.0
Re: [OE-core] [PATCH 1/7, v3] openssh: replace complete configuration files by patch
Why is the patch inappropriate for upstream submission? To me it looks like it should be at least proposed.
Alex
Quoted 282 lines · Enrico Scholz via lists.openembedded.org
From: Enrico Scholz <[email protected]>
Instead of shipping the whole configuration files for openssh, add small patch includes configuration snippets from subdirectories.
This allows us to keep the original upstream configuration which is mainly useful for documentation purposes. It makes it more easy to identify OE specific setup.
Signed-off-by Enrico Scholz <[email protected]>--- .../openssh/openssh/include-conf.patch | 34 +++++ .../openssh/openssh/ssh_config | 48 ------- .../openssh/openssh/sshd_config | 119 ------------------ .../openssh/openssh_9.6p1.bb | 5 +- 4 files changed, 35 insertions(+), 171 deletions(-) create mode 100644 meta/recipes-connectivity/openssh/openssh/include-conf.patch delete mode 100644 meta/recipes-connectivity/openssh/openssh/ssh_config delete mode 100644 meta/recipes-connectivity/openssh/openssh/sshd_configmeta/recipes-connectivity/openssh/openssh/include-conf.patch new file +34
-0@@ -0,0 +1,34 @@ +Include configuration snippets from subdirectory. + +NOTE: first configuration option wins. + +Upstream-Status: Inappropriate [configuration] + +Signed-off-by: Enrico Scholz <[email protected]> + +Index: openssh-9.5p1/ssh_config +=================================================================== +--- openssh-9.5p1.orig/ssh_config ++++ openssh-9.5p1/ssh_config +@@ -5,6 +5,8 @@ + # users, and the values can be changed in per-user configuration files + # or on the command line. + ++Include /etc/ssh/ssh_config.d/*.conf ++ + # Configuration data is parsed as follows: + # 1. command line options + # 2. user-specific file +Index: openssh-9.5p1/sshd_config +=================================================================== +--- openssh-9.5p1.orig/sshd_config ++++ openssh-9.5p1/sshd_config +@@ -10,6 +10,8 @@ + # possible, but leave them commented. Uncommented options override the + # default value. + ++Include /etc/ssh/sshd_config.d/*.conf ++ + #Port 22 + #AddressFamily any + #ListenAddress 0.0.0.0meta/recipes-connectivity/openssh/openssh/ssh_config deleted +0
-48@@ -1,48 +0,0 @@ -# $OpenBSD: ssh_config,v 1.35 2020/07/17 03:43:42 dtucker Exp $ - -# This is the ssh client system-wide configuration file. See -# ssh_config(5) for more information. This file provides defaults for -# users, and the values can be changed in per-user configuration files -# or on the command line. - -# Configuration data is parsed as follows: -# 1. command line options -# 2. user-specific file -# 3. system-wide file -# Any configuration value is only changed the first time it is set. -# Thus, host-specific definitions should be at the beginning of the -# configuration file, and defaults at the end. - -# Site-wide defaults for some commonly used options. For a comprehensive -# list of available options, their meanings and defaults, please see the -# ssh_config(5) man page. - -Include /etc/ssh/ssh_config.d/*.conf - -# Host * -# ForwardAgent no -# ForwardX11 no -# PasswordAuthentication yes -# HostbasedAuthentication no -# GSSAPIAuthentication no -# GSSAPIDelegateCredentials no -# BatchMode no -# CheckHostIP yes -# AddressFamily any -# ConnectTimeout 0 -# StrictHostKeyChecking ask -# IdentityFile ~/.ssh/id_rsa -# IdentityFile ~/.ssh/id_dsa -# IdentityFile ~/.ssh/id_ecdsa -# IdentityFile ~/.ssh/id_ed25519 -# Port 22 -# Ciphers aes128-ctr,aes192-ctr,aes256-ctr,aes128-cbc,3des-cbc -# MACs hmac-md5,hmac-sha1,[email protected] -# EscapeChar ~ -# Tunnel no -# TunnelDevice any:any -# PermitLocalCommand no -# VisualHostKey no -# ProxyCommand ssh -q -W %h:%p gateway.example.com -# RekeyLimit 1G 1h -# UserKnownHostsFile ~/.ssh/known_hosts.d/%kmeta/recipes-connectivity/openssh/openssh/sshd_config deleted +0
-119@@ -1,119 +0,0 @@ -# $OpenBSD: sshd_config,v 1.104 2021/07/02 05:11:21 dtucker Exp $ - -# This is the sshd server system-wide configuration file. See -# sshd_config(5) for more information. - -# This sshd was compiled with PATH=/usr/bin:/bin:/usr/sbin:/sbin - -# The strategy used for options in the default sshd_config shipped with -# OpenSSH is to specify options with their default value where -# possible, but leave them commented. Uncommented options override the -# default value. - -Include /etc/ssh/sshd_config.d/*.conf - -#Port 22 -#AddressFamily any -#ListenAddress 0.0.0.0 -#ListenAddress :: - -#HostKey /etc/ssh/ssh_host_rsa_key -#HostKey /etc/ssh/ssh_host_ecdsa_key -#HostKey /etc/ssh/ssh_host_ed25519_key - -# Ciphers and keying -#RekeyLimit default none - -# Logging -#SyslogFacility AUTH -#LogLevel INFO - -# Authentication: - -#LoginGraceTime 2m -#PermitRootLogin prohibit-password -#StrictModes yes -#MaxAuthTries 6 -#MaxSessions 10 - -#PubkeyAuthentication yes - -# The default is to check both .ssh/authorized_keys and .ssh/authorized_keys2 -# but this is overridden so installations will only check .ssh/authorized_keys -AuthorizedKeysFile .ssh/authorized_keys - -#AuthorizedPrincipalsFile none - -#AuthorizedKeysCommand none -#AuthorizedKeysCommandUser nobody - -# For this to work you will also need host keys in /etc/ssh/ssh_known_hosts -#HostbasedAuthentication no -# Change to yes if you don't trust ~/.ssh/known_hosts for -# HostbasedAuthentication -#IgnoreUserKnownHosts no -# Don't read the user's ~/.rhosts and ~/.shosts files -#IgnoreRhosts yes - -# To disable tunneled clear text passwords, change to no here! -#PasswordAuthentication yes -#PermitEmptyPasswords no - -# Change to yes to enable keyboard-interactive authentication (beware issues -# with some PAM modules and threads) -KbdInteractiveAuthentication no - -# Kerberos options -#KerberosAuthentication no -#KerberosOrLocalPasswd yes -#KerberosTicketCleanup yes -#KerberosGetAFSToken no - -# GSSAPI options -#GSSAPIAuthentication no -#GSSAPICleanupCredentials yes - -# Set this to 'yes' to enable PAM authentication, account processing, -# and session processing. If this is enabled, PAM authentication will -# be allowed through the KbdInteractiveAuthentication and -# PasswordAuthentication. Depending on your PAM configuration, -# PAM authentication via KbdInteractiveAuthentication may bypass -# the setting of "PermitRootLogin without-password". -# If you just want the PAM account and session checks to run without -# PAM authentication, then enable this but set PasswordAuthentication -# and KbdInteractiveAuthentication to 'no'. -#UsePAM no - -#AllowAgentForwarding yes -#AllowTcpForwarding yes -#GatewayPorts no -#X11Forwarding no -#X11DisplayOffset 10 -#X11UseLocalhost yes -#PermitTTY yes -#PrintMotd yes -#PrintLastLog yes -#TCPKeepAlive yes -#PermitUserEnvironment no -Compression no -ClientAliveInterval 15 -ClientAliveCountMax 4 -#UseDNS no -#PidFile /var/run/sshd.pid -#MaxStartups 10:30:100 -#PermitTunnel no -#ChrootDirectory none -#VersionAddendum none - -# no default banner path -#Banner none - -# override default of no subsystems -Subsystem sftp /usr/libexec/sftp-server - -# Example of overriding settings on a per-user basis -#Match User anoncvs -# X11Forwarding no -# AllowTcpForwarding no -# PermitTTY no -# ForceCommand cvs servermeta/recipes-connectivity/openssh/openssh_9.6p1.bb +1
-5@@ -12,8 +12,6 @@ DEPENDS = "zlib openssl virtual/crypt" DEPENDS += "${@bb.utils.contains('DISTRO_FEATURES', 'pam', 'libpam', '', d)}" SRC_URI = "http://ftp.openbsd.org/pub/OpenBSD/OpenSSH/portable/openssh-${PV}.tar.gz \ - file://sshd_config \ - file://ssh_config \ file://init \ ${@bb.utils.contains('DISTRO_FEATURES', 'pam', '${PAM_SRC_URI}', '', d)} \ file://sshd.service \@@ -23,6 +21,7 @@ SRC_URI = "http://ftp.openbsd.org/pub/OpenBSD/OpenSSH/portable/openssh-${PV}.tar file://volatiles.99_sshd \ file://run-ptest \ file://fix-potential-signed-overflow-in-pointer-arithmatic.patch \ + file://include-conf.patch \ file://sshd_check_keys \ file://add-test-support-for-busybox.patch \ file://0001-regress-banner.sh-log-input-and-output-files-on-erro.patch \@@ -101,8 +100,6 @@ CACHED_CONFIGUREVARS += "ac_cv_header_maillock_h=no" do_configure:prepend () { export LD="${CC}" - install -m 0644 ${WORKDIR}/sshd_config ${B}/ - install -m 0644 ${WORKDIR}/ssh_config ${B}/ } do_compile_ptest() { --2.44.0
-=-=-=-=-=-=-=-=-=-=-=-
Links: You receive all messages sent to this group.
View/Reply Online (#196975): https://lists.openembedded.org/g/openembedded-core/message/196975
Mute This Topic: https://lists.openembedded.org/mt/104882201/1686489
Group Owner: [email protected]
Unsubscribe: https://lists.openembedded.org/g/openembedded-core/unsub [[email protected]]
-=-=-=-=-=-=-=-=-=-=-=-
Re: [OE-core] [PATCH 1/7, v3] openssh: replace complete configuration files by patch
Quoted 4 lines · Alexander Kanavin
Why is the patch inappropriate for upstream submission? To me it looks like it should be at least proposed.
++Include
/etc/ssh/sshd_config.d/*.conf
Underlying feature exists for 4 years and nearly every major linux distribution (including OE) has such a line. So I assume there is a reason that it is not upstream yet.
I added an upstream report
(https://bugzilla.mindrot.org/show_bug.cgi?id=3672) and will update patch status when resubmitting.
Enrico
Re: [OE-core] [PATCH 1/7, v3] openssh: replace complete configuration files by patch
In reply to Enrico ScholzPlease always resend the whole series, the maintainer should have to go and cherry pick patches from various versions once the series has been dropped.
Quoted 282 lines · Enrico Scholz via lists.openembedded.org
From: Enrico Scholz <[email protected]>
Instead of shipping the whole configuration files for openssh, add small patch includes configuration snippets from subdirectories.
This allows us to keep the original upstream configuration which is mainly useful for documentation purposes. It makes it more easy to identify OE specific setup.
Signed-off-by Enrico Scholz <[email protected]>--- .../openssh/openssh/include-conf.patch | 34 +++++ .../openssh/openssh/ssh_config | 48 ------- .../openssh/openssh/sshd_config | 119 ------------------ .../openssh/openssh_9.6p1.bb | 5 +- 4 files changed, 35 insertions(+), 171 deletions(-) create mode 100644 meta/recipes-connectivity/openssh/openssh/include-conf.patch delete mode 100644 meta/recipes-connectivity/openssh/openssh/ssh_config delete mode 100644 meta/recipes-connectivity/openssh/openssh/sshd_configmeta/recipes-connectivity/openssh/openssh/include-conf.patch new file +34
-0@@ -0,0 +1,34 @@ +Include configuration snippets from subdirectory. + +NOTE: first configuration option wins. + +Upstream-Status: Inappropriate [configuration] + +Signed-off-by: Enrico Scholz <[email protected]> + +Index: openssh-9.5p1/ssh_config +=================================================================== +--- openssh-9.5p1.orig/ssh_config ++++ openssh-9.5p1/ssh_config +@@ -5,6 +5,8 @@ + # users, and the values can be changed in per-user configuration files + # or on the command line. + ++Include /etc/ssh/ssh_config.d/*.conf ++ + # Configuration data is parsed as follows: + # 1. command line options + # 2. user-specific file +Index: openssh-9.5p1/sshd_config +=================================================================== +--- openssh-9.5p1.orig/sshd_config ++++ openssh-9.5p1/sshd_config +@@ -10,6 +10,8 @@ + # possible, but leave them commented. Uncommented options override the + # default value. + ++Include /etc/ssh/sshd_config.d/*.conf ++ + #Port 22 + #AddressFamily any + #ListenAddress 0.0.0.0meta/recipes-connectivity/openssh/openssh/ssh_config deleted +0
-48@@ -1,48 +0,0 @@ -# $OpenBSD: ssh_config,v 1.35 2020/07/17 03:43:42 dtucker Exp $ - -# This is the ssh client system-wide configuration file. See -# ssh_config(5) for more information. This file provides defaults for -# users, and the values can be changed in per-user configuration files -# or on the command line. - -# Configuration data is parsed as follows: -# 1. command line options -# 2. user-specific file -# 3. system-wide file -# Any configuration value is only changed the first time it is set. -# Thus, host-specific definitions should be at the beginning of the -# configuration file, and defaults at the end. - -# Site-wide defaults for some commonly used options. For a comprehensive -# list of available options, their meanings and defaults, please see the -# ssh_config(5) man page. - -Include /etc/ssh/ssh_config.d/*.conf - -# Host * -# ForwardAgent no -# ForwardX11 no -# PasswordAuthentication yes -# HostbasedAuthentication no -# GSSAPIAuthentication no -# GSSAPIDelegateCredentials no -# BatchMode no -# CheckHostIP yes -# AddressFamily any -# ConnectTimeout 0 -# StrictHostKeyChecking ask -# IdentityFile ~/.ssh/id_rsa -# IdentityFile ~/.ssh/id_dsa -# IdentityFile ~/.ssh/id_ecdsa -# IdentityFile ~/.ssh/id_ed25519 -# Port 22 -# Ciphers aes128-ctr,aes192-ctr,aes256-ctr,aes128-cbc,3des-cbc -# MACs hmac-md5,hmac-sha1,[email protected] -# EscapeChar ~ -# Tunnel no -# TunnelDevice any:any -# PermitLocalCommand no -# VisualHostKey no -# ProxyCommand ssh -q -W %h:%p gateway.example.com -# RekeyLimit 1G 1h -# UserKnownHostsFile ~/.ssh/known_hosts.d/%kmeta/recipes-connectivity/openssh/openssh/sshd_config deleted +0
-119@@ -1,119 +0,0 @@ -# $OpenBSD: sshd_config,v 1.104 2021/07/02 05:11:21 dtucker Exp $ - -# This is the sshd server system-wide configuration file. See -# sshd_config(5) for more information. - -# This sshd was compiled with PATH=/usr/bin:/bin:/usr/sbin:/sbin - -# The strategy used for options in the default sshd_config shipped with -# OpenSSH is to specify options with their default value where -# possible, but leave them commented. Uncommented options override the -# default value. - -Include /etc/ssh/sshd_config.d/*.conf - -#Port 22 -#AddressFamily any -#ListenAddress 0.0.0.0 -#ListenAddress :: - -#HostKey /etc/ssh/ssh_host_rsa_key -#HostKey /etc/ssh/ssh_host_ecdsa_key -#HostKey /etc/ssh/ssh_host_ed25519_key - -# Ciphers and keying -#RekeyLimit default none - -# Logging -#SyslogFacility AUTH -#LogLevel INFO - -# Authentication: - -#LoginGraceTime 2m -#PermitRootLogin prohibit-password -#StrictModes yes -#MaxAuthTries 6 -#MaxSessions 10 - -#PubkeyAuthentication yes - -# The default is to check both .ssh/authorized_keys and .ssh/authorized_keys2 -# but this is overridden so installations will only check .ssh/authorized_keys -AuthorizedKeysFile .ssh/authorized_keys - -#AuthorizedPrincipalsFile none - -#AuthorizedKeysCommand none -#AuthorizedKeysCommandUser nobody - -# For this to work you will also need host keys in /etc/ssh/ssh_known_hosts -#HostbasedAuthentication no -# Change to yes if you don't trust ~/.ssh/known_hosts for -# HostbasedAuthentication -#IgnoreUserKnownHosts no -# Don't read the user's ~/.rhosts and ~/.shosts files -#IgnoreRhosts yes - -# To disable tunneled clear text passwords, change to no here! -#PasswordAuthentication yes -#PermitEmptyPasswords no - -# Change to yes to enable keyboard-interactive authentication (beware issues -# with some PAM modules and threads) -KbdInteractiveAuthentication no - -# Kerberos options -#KerberosAuthentication no -#KerberosOrLocalPasswd yes -#KerberosTicketCleanup yes -#KerberosGetAFSToken no - -# GSSAPI options -#GSSAPIAuthentication no -#GSSAPICleanupCredentials yes - -# Set this to 'yes' to enable PAM authentication, account processing, -# and session processing. If this is enabled, PAM authentication will -# be allowed through the KbdInteractiveAuthentication and -# PasswordAuthentication. Depending on your PAM configuration, -# PAM authentication via KbdInteractiveAuthentication may bypass -# the setting of "PermitRootLogin without-password". -# If you just want the PAM account and session checks to run without -# PAM authentication, then enable this but set PasswordAuthentication -# and KbdInteractiveAuthentication to 'no'. -#UsePAM no - -#AllowAgentForwarding yes -#AllowTcpForwarding yes -#GatewayPorts no -#X11Forwarding no -#X11DisplayOffset 10 -#X11UseLocalhost yes -#PermitTTY yes -#PrintMotd yes -#PrintLastLog yes -#TCPKeepAlive yes -#PermitUserEnvironment no -Compression no -ClientAliveInterval 15 -ClientAliveCountMax 4 -#UseDNS no -#PidFile /var/run/sshd.pid -#MaxStartups 10:30:100 -#PermitTunnel no -#ChrootDirectory none -#VersionAddendum none - -# no default banner path -#Banner none - -# override default of no subsystems -Subsystem sftp /usr/libexec/sftp-server - -# Example of overriding settings on a per-user basis -#Match User anoncvs -# X11Forwarding no -# AllowTcpForwarding no -# PermitTTY no -# ForceCommand cvs servermeta/recipes-connectivity/openssh/openssh_9.6p1.bb +1
-4@@ -12,8 +12,6 @@ DEPENDS = "zlib openssl virtual/crypt" DEPENDS += "${@bb.utils.contains('DISTRO_FEATURES', 'pam', 'libpam', '', d)}" SRC_URI = "http://ftp.openbsd.org/pub/OpenBSD/OpenSSH/portable/openssh-${PV}.tar.gz \ - file://sshd_config \ - file://ssh_config \ file://init \ ${@bb.utils.contains('DISTRO_FEATURES', 'pam', '${PAM_SRC_URI}', '', d)} \ file://sshd.service \@@ -23,6 +21,7 @@ SRC_URI = "http://ftp.openbsd.org/pub/OpenBSD/OpenSSH/portable/openssh-${PV}.tar file://volatiles.99_sshd \ file://run-ptest \ file://fix-potential-signed-overflow-in-pointer-arithmatic.patch \ + file://include-conf.patch \ file://sshd_check_keys \ file://add-test-support-for-busybox.patch \ file://0001-regress-banner.sh-log-input-and-output-files-on-erro.patch \@@ -101,8 +100,6 @@ CACHED_CONFIGUREVARS += "ac_cv_header_maillock_h=no" do_configure:prepend () { export LD="${CC}" - install -m 0644 ${WORKDIR}/sshd_config ${B}/ - install -m 0644 ${WORKDIR}/ssh_config ${B}/ } do_compile_ptest() {Signature · 11 lines
2.44.0 -=-=-=-=-=-=-=-=-=-=-=- Links: You receive all messages sent to this group. View/Reply Online (#196975): https://lists.openembedded.org/g/openembedded-core/message/196975 Mute This Topic: https://lists.openembedded.org/mt/104882201/3617179 Group Owner: [email protected] Unsubscribe: https://lists.openembedded.org/g/openembedded-core/unsub [[email protected]] -=-=-=-=-=-=-=-=-=-=-=-
Signature · 3 lines
Alexandre Belloni, co-owner and COO, Bootlin Embedded Linux and Kernel engineering https://bootlin.com
PATCH 2/7 openssh-config: initial checkin
In reply to Enrico ScholzFrom: Enrico Scholz <[email protected]>
Place OE specific openssh setup (which was removed in a previous patch) in a configuration snippet.
--- .../openssh/openssh-config.bb | 30 +++++++++++++++++++ .../openssh/openssh-config/80-oe.conf | 5 ++++ .../openssh/openssh_9.6p1.bb | 2 ++ 3 files changed, 37 insertions(+) create mode 100644 meta/recipes-connectivity/openssh/openssh-config.bb create mode 100644 meta/recipes-connectivity/openssh/openssh-config/80-oe.conf
meta/recipes-connectivity/openssh/openssh-config.bb new file +30 -0
@@ -0,0 +1,30 @@ +SUMMARY = "OE openssh configuration" +DESCRIPTION = "Provides openssh configuration snippets which correspond to IMAGE_FEATURE" +LICENSE = "MIT" +LIC_FILES_CHKSUM = "file://${COREBASE}/meta/COPYING.MIT;md5=3da9cfbcb788c80a0384361b4de20420" + +SRC_URI = "\ + file://80-oe.conf \ +" + +do_install() { + d=${D}${sysconfdir}/ssh/sshd_config.d + install -d "$d" + install -p -m 0644 \ + ${WORKDIR}/80-oe.conf \ + "$d"/ +} + +python populate_packages:prepend() { + dir = d.expand('${sysconfdir}/ssh/sshd_config.d') + + do_split_packages(d, dir, '^60-(.*)\.conf', + output_pattern='${PN}-%s', + description="openssh config for '%s' feature", + extra_depends='', + prepend=True) +} + +PACKAGES_DYNAMIC = "${PN}-*" + +FILES:${PN} = "${sysconfdir}/ssh/sshd_config.d/80-oe.conf"
meta/recipes-connectivity/openssh/openssh-config/80-oe.conf new file +5 -0
@@ -0,0 +1,5 @@ +KbdInteractiveAuthentication no + +Compression no +ClientAliveInterval 15 +ClientAliveCountMax 4
meta/recipes-connectivity/openssh/openssh_9.6p1.bb +2 -0
@@ -191,6 +191,8 @@ RCONFLICTS:${PN}-sshd = "dropbear" CONFFILES:${PN}-sshd = "${sysconfdir}/ssh/sshd_config" CONFFILES:${PN}-ssh = "${sysconfdir}/ssh/ssh_config" +RRECOMMENDS:${PN} += "openssh-config" + ALTERNATIVE_PRIORITY = "90" ALTERNATIVE:${PN}-scp = "scp" ALTERNATIVE:${PN}-ssh = "ssh"
Signature · 1 line
2.44.0
Patchtest results for [PATCH 2/7] openssh-config: initial checkin
Thank you for your submission. Patchtest identified one or more issues with the patch. Please see the log below for more information:
---
Testing patch /home/patchtest/share/mboxes/2-7-openssh-config-initial-checkin.patch
FAIL: test lic files chksum modified not mentioned: LIC_FILES_CHKSUM changed without "License-Update:" tag and description in commit message (test_metadata.TestMetadata.test_lic_files_chksum_modified_not_mentioned)
PASS: pretest src uri left files (test_metadata.TestMetadata.pretest_src_uri_left_files)
PASS: test CVE check ignore (test_metadata.TestMetadata.test_cve_check_ignore)
PASS: test Signed-off-by presence (test_mbox.TestMbox.test_signed_off_by_presence)
PASS: test author valid (test_mbox.TestMbox.test_author_valid)
PASS: test commit message presence (test_mbox.TestMbox.test_commit_message_presence)
PASS: test lic files chksum presence (test_metadata.TestMetadata.test_lic_files_chksum_presence)
PASS: test license presence (test_metadata.TestMetadata.test_license_presence)
PASS: test max line length (test_metadata.TestMetadata.test_max_line_length)
PASS: test mbox format (test_mbox.TestMbox.test_mbox_format)
PASS: test non-AUH upgrade (test_mbox.TestMbox.test_non_auh_upgrade)
PASS: test shortlog format (test_mbox.TestMbox.test_shortlog_format)
PASS: test shortlog length (test_mbox.TestMbox.test_shortlog_length)
PASS: test src uri left files (test_metadata.TestMetadata.test_src_uri_left_files)
PASS: test summary presence (test_metadata.TestMetadata.test_summary_presence)
SKIP: pretest pylint: No python related patches, skipping test (test_python_pylint.PyLint.pretest_pylint)
SKIP: test CVE tag format: No new CVE patches introduced (test_patch.TestPatch.test_cve_tag_format)
SKIP: test Signed-off-by presence: No new CVE patches introduced (test_patch.TestPatch.test_signed_off_by_presence)
SKIP: test Upstream-Status presence: No new CVE patches introduced (test_patch.TestPatch.test_upstream_status_presence_format)
SKIP: test bugzilla entry format: No bug ID found (test_mbox.TestMbox.test_bugzilla_entry_format)
SKIP: test pylint: No python related patches, skipping test (test_python_pylint.PyLint.test_pylint)
SKIP: test series merge on head: Merge test is disabled for now (test_mbox.TestMbox.test_series_merge_on_head)
SKIP: test target mailing list: Series merged, no reason to check other mailing lists (test_mbox.TestMbox.test_target_mailing_list)
---
Please address the issues identified and
submit a new revision of the patch, or alternatively, reply to this email with an explanation of why the patch should be accepted. If you believe these results are due to an error in patchtest, please submit a bug at https://bugzilla.yoctoproject.org/ (use the 'Patchtest' category under 'Yocto Project Subprojects'). For more information on specific failures, see: https://wiki.yoctoproject.org/wiki/Patchtest. Thank you!
Re: Patchtest results for [PATCH 2/7] openssh-config: initial checkin
Quoted 1 line · [email protected] writes:
FAIL: test lic files chksum modified not mentioned:
LIC_FILES_CHKSUMchanged without "License-Update:" tag and description in commit message (test_metadata.TestMetadata.test_lic_files_chksum_modified_not_mentioned)
This failure seems to be bogus; patch creates a new recipe with a new LIC_FILES_CHKSUM. It does not change/update an existing tag.
Enrico
Re: [OE-core] Patchtest results for [PATCH 2/7] openssh-config: initial checkin
Quoted 5 lines · Enrico Scholz via lists.openembedded.org
Quoted 1 line · [email protected] writes:
FAIL: test lic files chksum modified not mentioned:
LIC_FILES_CHKSUMchanged without "License-Update:" tag and description in commit message (test_metadata.TestMetadata.test_lic_files_chksum_modified_not_mentioned)This failure seems to be bogus; patch creates a new recipe with a new
LIC_FILES_CHKSUM. It does not change/update an existing tag.
Noted. We'll have to tweak the test...
Quoted 12 lines
Enrico
-=-=-=-=-=-=-=-=-=-=-=-
Links: You receive all messages sent to this group.
View/Reply Online (#196963): https://lists.openembedded.org/g/openembedded-core/message/196963
Mute This Topic: https://lists.openembedded.org/mt/104868543/7611679
Group Owner: [email protected]
Unsubscribe: https://lists.openembedded.org/g/openembedded-core/unsub [[email protected]]
-=-=-=-=-=-=-=-=-=-=-=-
PATCH 3/7 openssh: move configuration tweaking in configuration recipe
In reply to Enrico ScholzFrom: Enrico Scholz <[email protected]>
Instead of applying DISTRO_FEATURE based setup directly to sshd_config, add it to our configuration snippet.
--- meta/recipes-connectivity/openssh/openssh-config.bb | 10 ++++++++++ meta/recipes-connectivity/openssh/openssh_9.6p1.bb | 8 -------- 2 files changed, 10 insertions(+), 8 deletions(-)
meta/recipes-connectivity/openssh/openssh-config.bb +10 -0
@@ -13,6 +13,16 @@ do_install() { install -p -m 0644 \ ${WORKDIR}/80-oe.conf \ "$d"/ + + f=$d/80-oe.conf + + if [ "${@bb.utils.filter('DISTRO_FEATURES', 'pam', d)}" ]; then + echo "UsePAM yes" >> "$f" + fi + + if [ "${@bb.utils.filter('DISTRO_FEATURES', 'x11', d)}" ]; then + echo "X11Forwarding yes" >> "$f" + fi } python populate_packages:prepend() {
meta/recipes-connectivity/openssh/openssh_9.6p1.bb +0 -8
@@ -109,11 +109,6 @@ do_compile_ptest() { do_install:append () { if [ "${@bb.utils.filter('DISTRO_FEATURES', 'pam', d)}" ]; then install -D -m 0644 ${WORKDIR}/sshd ${D}${sysconfdir}/pam.d/sshd - sed -i -e 's:#UsePAM no:UsePAM yes:' ${D}${sysconfdir}/ssh/sshd_config - fi - - if [ "${@bb.utils.filter('DISTRO_FEATURES', 'x11', d)}" ]; then - sed -i -e 's:#X11Forwarding no:X11Forwarding yes:' ${D}${sysconfdir}/ssh/sshd_config fi install -d ${D}${sysconfdir}/init.d
@@ -188,9 +183,6 @@ RPROVIDES:${PN}-sshd = "sshd" RCONFLICTS:${PN} = "dropbear" RCONFLICTS:${PN}-sshd = "dropbear" -CONFFILES:${PN}-sshd = "${sysconfdir}/ssh/sshd_config" -CONFFILES:${PN}-ssh = "${sysconfdir}/ssh/ssh_config" - RRECOMMENDS:${PN} += "openssh-config" ALTERNATIVE_PRIORITY = "90"
Signature · 1 line
2.44.0
PATCH 4/7 image: prepare openssh configuration
In reply to Enrico ScholzFrom: Enrico Scholz <[email protected]>
Add an OPENSSH_FEATURE_CONFIGURATION variable which will hold openssh configuration packages.
--- meta/classes-recipe/core-image.bbclass | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-)
meta/classes-recipe/core-image.bbclass +4 -1
@@ -55,7 +55,7 @@ FEATURE_PACKAGES_tools-sdk = "packagegroup-core-sdk packagegroup-core-standalone FEATURE_PACKAGES_nfs-server = "packagegroup-core-nfs-server" FEATURE_PACKAGES_nfs-client = "packagegroup-core-nfs-client" FEATURE_PACKAGES_ssh-server-dropbear = "packagegroup-core-ssh-dropbear" -FEATURE_PACKAGES_ssh-server-openssh = "packagegroup-core-ssh-openssh" +FEATURE_PACKAGES_ssh-server-openssh = "packagegroup-core-ssh-openssh ${OPENSSH_FEATURE_CONFIGURATION}" FEATURE_PACKAGES_hwcodecs = "${MACHINE_HWCODECS}"
@@ -83,4 +83,7 @@ CORE_IMAGE_EXTRA_INSTALL ?= "" IMAGE_INSTALL ?= "${CORE_IMAGE_BASE_INSTALL}" +OPENSSH_FEATURE_CONFIGURATION = "\ +" + inherit image
Signature · 1 line
2.44.0
PATCH 5/7 openssh: replace 'allow-empty-password' rootfs scipt by configuration
In reply to Enrico ScholzFrom: Enrico Scholz <[email protected]>
Install 'openssh-config-allow-empty-password' when corresponding IMAGE_FEATURES are active.
--- meta/classes-recipe/core-image.bbclass | 1 + meta/classes-recipe/rootfs-postcommands.bbclass | 6 ------ meta/recipes-connectivity/openssh/openssh-config.bb | 2 ++ .../openssh/openssh-config/60-allow-empty-password.conf | 1 + 4 files changed, 4 insertions(+), 6 deletions(-) create mode 100644 meta/recipes-connectivity/openssh/openssh-config/60-allow-empty-password.conf
meta/classes-recipe/core-image.bbclass +1 -0
@@ -84,6 +84,7 @@ CORE_IMAGE_EXTRA_INSTALL ?= "" IMAGE_INSTALL ?= "${CORE_IMAGE_BASE_INSTALL}" OPENSSH_FEATURE_CONFIGURATION = "\ + ${@bb.utils.contains_any('IMAGE_FEATURES', [ 'debug-tweaks', 'allow-empty-password' ], 'openssh-config-allow-empty-password', '',d)} \ " inherit image
meta/classes-recipe/rootfs-postcommands.bbclass +0 -6
@@ -246,12 +246,6 @@ zap_empty_root_password () { # allow dropbear/openssh to accept logins from accounts with an empty password string # ssh_allow_empty_password () { - for config in sshd_config sshd_config_readonly; do - if [ -e ${IMAGE_ROOTFS}${sysconfdir}/ssh/$config ]; then - sed -i 's/^[#[:space:]]*PermitEmptyPasswords.*/PermitEmptyPasswords yes/' ${IMAGE_ROOTFS}${sysconfdir}/ssh/$config - fi - done - if [ -e ${IMAGE_ROOTFS}${sbindir}/dropbear ] ; then if grep -q DROPBEAR_EXTRA_ARGS ${IMAGE_ROOTFS}${sysconfdir}/default/dropbear 2>/dev/null ; then if ! grep -q "DROPBEAR_EXTRA_ARGS=.*-B" ${IMAGE_ROOTFS}${sysconfdir}/default/dropbear ; then
meta/recipes-connectivity/openssh/openssh-config.bb +2 -0
@@ -4,6 +4,7 @@ LICENSE = "MIT" LIC_FILES_CHKSUM = "file://${COREBASE}/meta/COPYING.MIT;md5=3da9cfbcb788c80a0384361b4de20420" SRC_URI = "\ + file://60-allow-empty-password.conf \ file://80-oe.conf \ "
@@ -11,6 +12,7 @@ do_install() { d=${D}${sysconfdir}/ssh/sshd_config.d install -d "$d" install -p -m 0644 \ + ${WORKDIR}/60-allow-empty-password.conf \ ${WORKDIR}/80-oe.conf \ "$d"/
meta/recipes-connectivity/openssh/openssh-config/60-allow-empty-password.conf new file +1 -0
@@ -0,0 +1 @@ +PermitEmptyPasswords yes
Signature · 1 line
2.44.0
PATCH 6/7 openssh: replace 'allow-root-login' rootfs scipt by configuration
In reply to Enrico ScholzFrom: Enrico Scholz <[email protected]>
Install 'openssh-config-allow-root-login' when corresponding IMAGE_FEATURES are active.
--- meta/classes-recipe/core-image.bbclass | 1 + meta/classes-recipe/rootfs-postcommands.bbclass | 6 ------ meta/recipes-connectivity/openssh/openssh-config.bb | 2 ++ .../openssh/openssh-config/60-allow-root-login.conf | 1 + 4 files changed, 4 insertions(+), 6 deletions(-) create mode 100644 meta/recipes-connectivity/openssh/openssh-config/60-allow-root-login.conf
meta/classes-recipe/core-image.bbclass +1 -0
@@ -85,6 +85,7 @@ IMAGE_INSTALL ?= "${CORE_IMAGE_BASE_INSTALL}" OPENSSH_FEATURE_CONFIGURATION = "\ ${@bb.utils.contains_any('IMAGE_FEATURES', [ 'debug-tweaks', 'allow-empty-password' ], 'openssh-config-allow-empty-password', '',d)} \ + ${@bb.utils.contains_any('IMAGE_FEATURES', [ 'debug-tweaks', 'allow-root-login' ], 'openssh-config-allow-root-login', '',d)} \ " inherit image
meta/classes-recipe/rootfs-postcommands.bbclass +0 -6
@@ -268,12 +268,6 @@ ssh_allow_empty_password () { # allow dropbear/openssh to accept root logins # ssh_allow_root_login () { - for config in sshd_config sshd_config_readonly; do - if [ -e ${IMAGE_ROOTFS}${sysconfdir}/ssh/$config ]; then - sed -i 's/^[#[:space:]]*PermitRootLogin.*/PermitRootLogin yes/' ${IMAGE_ROOTFS}${sysconfdir}/ssh/$config - fi - done - if [ -e ${IMAGE_ROOTFS}${sbindir}/dropbear ] ; then if grep -q DROPBEAR_EXTRA_ARGS ${IMAGE_ROOTFS}${sysconfdir}/default/dropbear 2>/dev/null ; then sed -i '/^DROPBEAR_EXTRA_ARGS=/ s/-w//' ${IMAGE_ROOTFS}${sysconfdir}/default/dropbear
meta/recipes-connectivity/openssh/openssh-config.bb +2 -0
@@ -5,6 +5,7 @@ LIC_FILES_CHKSUM = "file://${COREBASE}/meta/COPYING.MIT;md5=3da9cfbcb788c80a0384 SRC_URI = "\ file://60-allow-empty-password.conf \ + file://60-allow-root-login.conf \ file://80-oe.conf \ "
@@ -13,6 +14,7 @@ do_install() { install -d "$d" install -p -m 0644 \ ${WORKDIR}/60-allow-empty-password.conf \ + ${WORKDIR}/60-allow-root-login.conf \ ${WORKDIR}/80-oe.conf \ "$d"/
meta/recipes-connectivity/openssh/openssh-config/60-allow-root-login.conf new file +1 -0
@@ -0,0 +1 @@ +PermitRootLogin yes
Signature · 1 line
2.44.0
PATCH 7/7 openssh: move read-only-rootfs setup in configuration snippet
In reply to Enrico ScholzFrom: Enrico Scholz <[email protected]>
This patch replaces the duplicate 'sshd_config_readonly' configuration file and logic behind by an extra packages which is installed when corresponding IMAGE_FEATURES are set.
**NOTE**: this causes a regression when host keys are added manually to the image. Users have to do
| OPENSSH_FEATURE_CONFIGURATION:remove = "openssh-config-read-only-rootfs"
in this case, or create a .bbappend for openssh-config which sets RO_KEYDIR.
--- meta/classes-recipe/core-image.bbclass | 12 ++++++++++++ meta/classes-recipe/rootfs-postcommands.bbclass | 13 +------------ meta/recipes-connectivity/openssh/openssh-config.bb | 7 +++++++ meta/recipes-connectivity/openssh/openssh_9.6p1.bb | 7 +------ 4 files changed, 21 insertions(+), 18 deletions(-)
meta/classes-recipe/core-image.bbclass +12 -0
@@ -84,8 +84,20 @@ CORE_IMAGE_EXTRA_INSTALL ?= "" IMAGE_INSTALL ?= "${CORE_IMAGE_BASE_INSTALL}" OPENSSH_FEATURE_CONFIGURATION = "\ + ${@'openssh-config-read-only-rootfs' if etc_is_readonly(d) else ''} \ ${@bb.utils.contains_any('IMAGE_FEATURES', [ 'debug-tweaks', 'allow-empty-password' ], 'openssh-config-allow-empty-password', '',d)} \ ${@bb.utils.contains_any('IMAGE_FEATURES', [ 'debug-tweaks', 'allow-root-login' ], 'openssh-config-allow-root-login', '',d)} \ " +def etc_is_readonly(d): + features = (d.getVar('IMAGE_FEATURES') or "").split() + + if 'read-only-rootfs' not in features: + return False + + if 'stateless-rootfs' in features: + return True + + return 'overlayfs-etc' not in features + inherit image
meta/classes-recipe/rootfs-postcommands.bbclass +1 -12
@@ -188,21 +188,10 @@ read_only_rootfs_hook () { fi # If we're using openssh and the /etc/ssh directory has no pre-generated keys, - # we should configure openssh to use the configuration file /etc/ssh/sshd_config_readonly - # and the keys under /var/run/ssh. + # we should configure dropbear to use the keys under /var/lib/dropbear # If overlayfs-etc is used this is not done as /etc is treated as writable # If stateless-rootfs is enabled this is always done as we don't want to save keys then if ${@ 'true' if not bb.utils.contains('IMAGE_FEATURES', 'overlayfs-etc', True, False, d) or bb.utils.contains('IMAGE_FEATURES', 'stateless-rootfs', True, False, d) else 'false'}; then - if [ -d ${IMAGE_ROOTFS}/etc/ssh ]; then - if [ -e ${IMAGE_ROOTFS}/etc/ssh/ssh_host_rsa_key ]; then - echo "SYSCONFDIR=\${SYSCONFDIR:-/etc/ssh}" >> ${IMAGE_ROOTFS}/etc/default/ssh - echo "SSHD_OPTS=" >> ${IMAGE_ROOTFS}/etc/default/ssh - else - echo "SYSCONFDIR=\${SYSCONFDIR:-/var/run/ssh}" >> ${IMAGE_ROOTFS}/etc/default/ssh - echo "SSHD_OPTS='-f /etc/ssh/sshd_config_readonly'" >> ${IMAGE_ROOTFS}/etc/default/ssh - fi - fi - # Also tweak the key location for dropbear in the same way. if [ -d ${IMAGE_ROOTFS}/etc/dropbear ]; then if [ ! -e ${IMAGE_ROOTFS}/etc/dropbear/dropbear_rsa_host_key ]; then
meta/recipes-connectivity/openssh/openssh-config.bb +7 -0
@@ -9,6 +9,9 @@ SRC_URI = "\ file://80-oe.conf \ " +RO_KEYDIR ??= "/var/run/ssh" +KEY_ALGORITHMS ??= "rsa ecdsa ed25519" + do_install() { d=${D}${sysconfdir}/ssh/sshd_config.d install -d "$d"
@@ -27,6 +30,10 @@ do_install() { if [ "${@bb.utils.filter('DISTRO_FEATURES', 'x11', d)}" ]; then echo "X11Forwarding yes" >> "$f" fi + + for alg in ${KEY_ALGORITHMS}; do + printf 'HostKey %s/ssh_host_%s_key\n' '${RO_KEYDIR}' "$alg" + done > $d/60-read-only-rootfs.conf } python populate_packages:prepend() {
meta/recipes-connectivity/openssh/openssh_9.6p1.bb +1 -6
@@ -121,11 +121,6 @@ do_install:append () { # Create config files for read-only rootfs install -d ${D}${sysconfdir}/ssh - install -m 644 ${D}${sysconfdir}/ssh/sshd_config ${D}${sysconfdir}/ssh/sshd_config_readonly - sed -i '/HostKey/d' ${D}${sysconfdir}/ssh/sshd_config_readonly - echo "HostKey /var/run/ssh/ssh_host_rsa_key" >> ${D}${sysconfdir}/ssh/sshd_config_readonly - echo "HostKey /var/run/ssh/ssh_host_ecdsa_key" >> ${D}${sysconfdir}/ssh/sshd_config_readonly - echo "HostKey /var/run/ssh/ssh_host_ed25519_key" >> ${D}${sysconfdir}/ssh/sshd_config_readonly install -d ${D}${systemd_system_unitdir} if ${@bb.utils.contains('PACKAGECONFIG','systemd-sshd-socket-mode','true','false',d)}; then
@@ -165,7 +160,7 @@ PACKAGES =+ "${PN}-keygen ${PN}-scp ${PN}-ssh ${PN}-sshd ${PN}-sftp ${PN}-misc $ FILES:${PN}-scp = "${bindir}/scp.${BPN}" FILES:${PN}-ssh = "${bindir}/ssh.${BPN} ${sysconfdir}/ssh/ssh_config" FILES:${PN}-sshd = "${sbindir}/sshd ${sysconfdir}/init.d/sshd ${systemd_system_unitdir}" -FILES:${PN}-sshd += "${sysconfdir}/ssh/moduli ${sysconfdir}/ssh/sshd_config ${sysconfdir}/ssh/sshd_config_readonly ${sysconfdir}/default/volatiles/99_sshd ${sysconfdir}/pam.d/sshd" +FILES:${PN}-sshd += "${sysconfdir}/ssh/moduli ${sysconfdir}/ssh/sshd_config ${sysconfdir}/default/volatiles/99_sshd ${sysconfdir}/pam.d/sshd" FILES:${PN}-sshd += "${libexecdir}/${BPN}/sshd_check_keys" FILES:${PN}-sftp = "${bindir}/sftp" FILES:${PN}-sftp-server = "${libexecdir}/sftp-server"
Signature · 1 line
2.44.0
It's a very much welcome refactoring (existing code is an inconsistent mess), but there's also a feature freeze right now, and this patchset is invasive. Can you resubmit once the LTS is out?
Alex
Quoted 95 lines · Enrico Scholz via lists.openembedded.org
To deal with system setups, sshd was configured in the following way:
-
sshd_configis shipped completely by OE andDISTRO_FEATURES(pam, x11) are patched in duringdo_install--> this is difficulty to maintain; e.g.
sshd_configmust be
synchronized between OpenSSH releases and OE adaptations manually inserted- two different configuration files (
sshd_config+sshd_config_readonly) are created;IMAGE_FEATURESdecides which one is used and it is patched in aROOTFS_COMMANDin the system--> this make it difficult for third party recipes to incorporate
their changes (they have to go over both files)--> the readonly HostKey locations and algorithms are hardcoded
which makes it difficult to place them e.g. on a persistent /opt partition and disable e.g. ecdsa- depending on
IMAGE_FEATURES(empty passwords, root login), both files are patched by aROOTFS_POSTCOMMAND--> these changes are lost when pkgmgmt is used for the image and
openssh being updatedThe patchset:
- reduces changes to
sshd_configto| Include
/etc/ssh/sshd_config.d/*.conf--> This is already the done in current recipe and most mainline
Linux distributions are doing it- moves configuration in new openssh-config recipe which is a weak dependency of openssh (and can be replaced by another
IMAGE_INSTALL)Recipe ships configuration as small snippets which might contain dynamically created content (e.g. 'UsePAM yes')
-
IMAGE_FEATUREbased setup is done by creating subpackages with the corresponding options. These subpackages are added to FEATURE_PACKAGES_ssh-server-openssh- readonly rootfs setup has been enhanced by
| RO_KEYDIR ??= "/var/run/ssh" | KEY_ALGORITHMS ??= "rsa ecdsa ed25519" parameters which can be overridden.Enrico Scholz (7):
openssh: replace complete configuration files by patch
openssh-config: initial checkin
openssh: move configuration tweaking in configuration recipe
image: prepare openssh configuration
openssh: replace 'allow-empty-password' rootfs scipt by configuration
openssh: replace 'allow-root-login' rootfs scipt by configuration
openssh: move read-only-rootfs setup in configuration snippetmeta/classes-recipe/core-image.bbclass | 19 ++- .../rootfs-postcommands.bbclass | 25 +--- .../openssh/openssh-config.bb | 51 ++++++++ .../60-allow-empty-password.conf | 1 + .../openssh-config/60-allow-root-login.conf | 1 + .../openssh/openssh-config/80-oe.conf | 5 + .../openssh/openssh/include-conf.patch | 32 +++++ .../openssh/openssh/ssh_config | 48 ------- .../openssh/openssh/sshd_config | 119 ------------------ .../openssh/openssh_9.6p1.bb | 20 +-- 10 files changed, 112 insertions(+), 209 deletions(-) create mode 100644 meta/recipes-connectivity/openssh/openssh-config.bb create mode 100644 meta/recipes-connectivity/openssh/openssh-config/60-allow-empty-password.conf create mode 100644 meta/recipes-connectivity/openssh/openssh-config/60-allow-root-login.conf create mode 100644 meta/recipes-connectivity/openssh/openssh-config/80-oe.conf create mode 100644 meta/recipes-connectivity/openssh/openssh/include-conf.patch delete mode 100644 meta/recipes-connectivity/openssh/openssh/ssh_config delete mode 100644 meta/recipes-connectivity/openssh/openssh/sshd_config--
2.44.0-=-=-=-=-=-=-=-=-=-=-=-
Links: You receive all messages sent to this group.
View/Reply Online (#196955): https://lists.openembedded.org/g/openembedded-core/message/196955
Mute This Topic: https://lists.openembedded.org/mt/104868003/1686489
Group Owner: [email protected]
Unsubscribe: https://lists.openembedded.org/g/openembedded-core/unsub [[email protected]]
-=-=-=-=-=-=-=-=-=-=-=-
Quoted 46 lines · Enrico Scholz via lists.openembedded.org
To deal with system setups, sshd was configured in the following way:
-
sshd_configis shipped completely by OE andDISTRO_FEATURES(pam, x11) are patched in duringdo_install--> this is difficulty to maintain; e.g.
sshd_configmust be synchronized between OpenSSH releases and OE adaptations manually inserted- two different configuration files (
sshd_config+sshd_config_readonly) are created;IMAGE_FEATURESdecides which one is used and it is patched in aROOTFS_COMMANDin the system--> this make it difficult for third party recipes to incorporate their changes (they have to go over both files)
--> the readonly HostKey locations and algorithms are hardcoded which makes it difficult to place them e.g. on a persistent /opt partition and disable e.g. ecdsa
- depending on
IMAGE_FEATURES(empty passwords, root login), both files are patched by aROOTFS_POSTCOMMAND--> these changes are lost when pkgmgmt is used for the image and openssh being updated
The patchset:
- reduces changes to
sshd_configto| Include
/etc/ssh/sshd_config.d/*.conf--> This is already the done in current recipe and most mainline Linux distributions are doing it
- moves configuration in new openssh-config recipe which is a weak dependency of openssh (and can be replaced by another
IMAGE_INSTALL)Recipe ships configuration as small snippets which might contain dynamically created content (e.g. 'UsePAM yes')
-
IMAGE_FEATUREbased setup is done by creating subpackages with the corresponding options. These subpackages are added to FEATURE_PACKAGES_ssh-server-openssh
Quoted 6 lines
- readonly rootfs setup has been enhanced by
|
RO_KEYDIR??= "/var/run/ssh"
|KEY_ALGORITHMS??= "rsa ecdsa ed25519"parameters which can be overridden.
Thanks for sending this. I suspect something like this might be desirable however unfortunately the timing is a little tricky as we're just past the feature freeze point for 5.0.
I know people often want to push for the inclusion of things into something like the LTS so I did put this through the automated testing, just to get an idea of the potential issues.
The first run had lots of these warnings:
https://autobuilder.yoctoproject.org/typhoon/#/builders/63/builds/8649/steps/14/logs/warnings
so I squashed a fix in for that. The second run had this:
https://autobuilder.yoctoproject.org/typhoon/#/builders/81/builds/6390/steps/12/logs/stdio
which suggests ssh connections into our image testing doesn't work. It is unclear why that is failing there but there were indications in the previous build that other ssh connections were working ok. It could be dropbear vs openssh at a guess. That build is still ongoing too so there may be other issues.
Anyway I just wanted to highlight the testing results and to say that this is something we should think about but it will have to wait until after 5.0 releases.
I haven't reviewed the patches in much detail, I mainly wanted to get the automated testing results shared.
Cheers,
Richard
Quoted 3 lines · Richard Purdie
Thanks for sending this. I suspect something like this might be desirable however unfortunately the timing is a little tricky as we're just past the feature freeze point for 5.0.
ok; my fault. I delayed it too much.
Would it be possible to communicate such schedules more visibly? E.g. put a link on https://wiki.yoctoproject.org/wiki/Releases ?
Quoted 1 line
https://autobuilder.yoctoproject.org/typhoon/#/builders/63/builds/8649/steps/14/logs/warnings
ok
Quoted 3 lines
so I squashed a fix in for that. The second run had this:
https://autobuilder.yoctoproject.org/typhoon/#/builders/81/builds/6390/steps/12/logs/stdio
It is difficulty for me to analyze this from the outside. The patchset requires that the 'openssh-sshd' IMAGE_FEATURE is set; installing the package manually does not suffice anymore.
I can not detect such an IMAGE_FEATURE configuration in step 10; but I might miss other setup.
Enrico
Quoted 11 lines · Enrico Scholz
Quoted 4 lines · Richard Purdie
Thanks for sending this. I suspect something like this might be desirable however unfortunately the timing is a little tricky as we're
just past the feature freeze point for 5.0.ok; my fault. I delayed it too much.
Would it be possible to communicate such schedules more visibly? E.g. put a link on https://wiki.yoctoproject.org/wiki/Releases ?
The dates are being updated here:
https://wiki.yoctoproject.org/wiki/Weekly_Status
and in weekly status emails sent to the yocto and openembedded-core mailing lists.
Quoted 5 lines
Quoted 1 line
https://autobuilder.yoctoproject.org/typhoon/#/builders/63/builds/8649/steps/14/logs/warnings
ok
Quoted 7 lines
Quoted 3 lines
so I squashed a fix in for that. The second run had this:
https://autobuilder.yoctoproject.org/typhoon/#/builders/81/builds/6390/steps/12/logs/stdio
It is difficulty for me to analyze this from the outside. The patchset requires that the 'openssh-sshd'
IMAGE_FEATUREis set; installing the package manually does not suffice anymore.
That is probably something we may need to improve since lots of others would expect installing the package to work.
I suspect meta/recipes-core/images/core-image-ptest.bb setting
IMAGE_INSTALL:append = " ${MCNAME}-ptest openssh"
will be the cause.
I don't really time to spend thinking about this now unfortunately as there will be other priorities for the release.
Cheers,
Richard
A message that is not in the archive (sent off-list or not yet received): [email protected]
Quoted 90 lines · Richard Purdie via lists.openembedded.org
Quoted 53 lines · Enrico Scholz via lists.openembedded.org
To deal with system setups, sshd was configured in the following way:
-
sshd_configis shipped completely by OE andDISTRO_FEATURES(pam,
x11) are patched in duringdo_install--> this is difficulty to maintain; e.g.
sshd_configmust be synchronized between OpenSSH releases and OE adaptations manually inserted- two different configuration files (
sshd_config+sshd_config_readonly)
are created;IMAGE_FEATURESdecides which one is used and it is patched
in aROOTFS_COMMANDin the system--> this make it difficult for third party recipes to incorporate
their changes (they have to go over both files)--> the readonly HostKey locations and algorithms are hardcoded which makes it difficult to place them e.g. on a persistent /opt partition and disable e.g. ecdsa
- depending on
IMAGE_FEATURES(empty passwords, root login), both files are patched by aROOTFS_POSTCOMMAND--> these changes are lost when pkgmgmt is used for the image and
openssh being updatedThe patchset:
- reduces changes to
sshd_configto| Include
/etc/ssh/sshd_config.d/*.conf--> This is already the done in current recipe and most mainline Linux distributions are doing it
- moves configuration in new openssh-config recipe which is a weak dependency of openssh (and can be replaced by another
IMAGE_INSTALL)Recipe ships configuration as small snippets which might contain dynamically created content (e.g. 'UsePAM yes')
-
IMAGE_FEATUREbased setup is done by creating subpackages with the corresponding options. These subpackages are added to FEATURE_PACKAGES_ssh-server-opensshQuoted 6 lines
- readonly rootfs setup has been enhanced by
|
RO_KEYDIR??= "/var/run/ssh"
|KEY_ALGORITHMS??= "rsa ecdsa ed25519"parameters which can be overridden.
Thanks for sending this. I suspect something like this might be desirable however unfortunately the timing is a little tricky as we're
just past the feature freeze point for 5.0.I know people often want to push for the inclusion of things into something like the LTS so I did put this through the automated testing,
just to get an idea of the potential issues.The first run had lots of these warnings:
https://autobuilder.yoctoproject.org/typhoon/#/builders/63/builds/8649/steps/14/logs/warnings
so I squashed a fix in for that. The second run had this:
https://autobuilder.yoctoproject.org/typhoon/#/builders/81/builds/6390/steps/12/logs/stdio
which suggests ssh connections into our image testing doesn't work. It
is unclear why that is failing there but there were indications in the
previous build that other ssh connections were working ok. It could be
dropbear vs openssh at a guess. That build is still ongoing too so there may be other issues.
Quoted 7 lines
Anyway I just wanted to highlight the testing results and to say that this is something we should think about but it will have to wait until
after 5.0 releases.I haven't reviewed the patches in much detail, I mainly wanted to get the automated testing results shared.
Some further related warnings:
https://autobuilder.yoctoproject.org/typhoon/#/builders/23/builds/9031/steps/11/logs/warnings
Cheers,
Richard
Quoted 3 lines · Richard Purdie
Some further related warnings:
https://autobuilder.yoctoproject.org/typhoon/#/builders/23/builds/9031/steps/11/logs/warnins
| stdio: WARNING: Nothing RPROVIDES 'nativesdk-openssh-config' ...
ok
I will reduce dependency from
|-RRECOMMENDS:${PN} += "openssh-config"
to
|+RRECOMMENDS:${PN}-sshd:class-target += "openssh-config"
| stdio: WARNING: Nothing RPROVIDES 'nativesdk-openssh-scp' ... | stdio: WARNING: Nothing RPROVIDES 'nativesdk-openssh-sshd' ... | stdio: WARNING: Nothing RPROVIDES 'nativesdk-openssh-ssh' ...
are these warnings really new?
Enrico
Quoted 5 lines · Enrico Scholz via lists.openembedded.org
| stdio: WARNING: Nothing RPROVIDES 'nativesdk-openssh-scp' ... | stdio: WARNING: Nothing RPROVIDES 'nativesdk-openssh-sshd' ... | stdio: WARNING: Nothing RPROVIDES 'nativesdk-openssh-ssh' ...are these warnings really new?
They are. Warnings are not allowed to creep in and linger around, so master is always free of them (except for intermittent ptest fails, which this one isn't).
Alex