mmc: sdhci-of-dwcmshc: Add CQE support
Subsystems (3)
v7 cover mmc: sdhci-of-dwcmshc: Add CQE support
Hello!
This is implementation of SDHCI CQE support for sdhci-of-dwcmshc driver. For enabling CQE support just set 'supports-cqe' in your DevTree file for appropriate mmc node.
Also, while implementing CQE support for the driver, I faced with a problem which I will describe below.
According to the IP block documentation CQE works only with "AMDA-2 only" mode which is activated only with v4 mode enabled. I see in dwcmshc_probe() function that v4 mode gets enabled only for 'sdhci_dwcmshc_bf3_pdata' platform data.
So my question is: is it correct to enable v4 mode for all platform data if 'SDHCI_CAN_64BIT_V4' bit is set in hw?
Because I`m afraid that enabling v4 mode for some platforms could break them down. On the other hand, if host controller says that it can do v4 (caps & SDHCI_CAN_64BIT_V4), lets do v4 or disable it manualy by some quirk. Anyway - RFC.
v2:
- Added dwcmshc specific cqe_disable hook to prevent losing in-flight cmd when an ioctl is issued and cqe_disable is called;
- Added processing 128Mb boundary for the host memory data buffer size and the data buffer. For implementing this processing an extra callback is added to the struct 'sdhci_ops'.
- Fixed typo.
v3:
- Fix warning reported by kernel test robot:
| Reported-by: kernel test robot <[email protected]> | Closes: https://lore.kernel.org/oe-kbuild-all/[email protected]/ | Closes: https://lore.kernel.org/oe-kbuild-all/[email protected]/
v4:
- Data reset moved to custom driver tuning hook.
- Removed unnecessary dwcmshc_sdhci_cqe_disable() func
- Removed unnecessary dwcmshc_cqhci_set_tran_desc. Export and use cqhci_set_tran_desc() instead.
- Provide a hook for cqhci_set_tran_desc() instead of cqhci_prep_tran_desc().
- Fix typo: int_clok_disable --> int_clock_disable
v5:
- Fix warning reported by kernel test robot:
| Reported-by: kernel test robot <[email protected]> | Closes: https://lore.kernel.org/oe-kbuild-all/[email protected]/
v6:
- Rebase to master branch
- Fix typo;
- Fix double blank line;
- Add cqhci_suspend() and cqhci_resume() functions
to support mmc suspend-to-ram (s2r);
- Move reading DWCMSHC_P_VENDOR_AREA2 register under "supports-cqe" condition as not all IPs have that register;
- Remove sdhci V4 mode from the list of prerequisites to init cqhci.
v7:
- Add disabling MMC_CAP2_CQE and MMC_CAP2_CQE_DCMD caps in case of CQE init fails to prevent problems in suspend/resume functions.
Sergey Khimich (2):
mmc: cqhci: Add cqhci set_tran_desc() callback
mmc: sdhci-of-dwcmshc: Implement SDHCI CQE support
drivers/mmc/host/Kconfig | 1 + drivers/mmc/host/cqhci-core.c | 11 +- drivers/mmc/host/cqhci.h | 4 + drivers/mmc/host/sdhci-of-dwcmshc.c | 191 +++++++++++++++++++++++++++- 4 files changed, 202 insertions(+), 5 deletions(-)
Signature · 1 line
2.30.2
PATCH v7 1/2 mmc: cqhci: Add cqhci set_tran_desc() callback
From: Sergey Khimich <[email protected]>
There are could be specific limitations for some mmc controllers for setting cqhci transfer descriptors. So add callback to allow implement driver specific function.
--- drivers/mmc/host/cqhci-core.c | 11 ++++++++--- drivers/mmc/host/cqhci.h | 4 ++++ 2 files changed, 12 insertions(+), 3 deletions(-)
drivers/mmc/host/cqhci-core.c +8 -3
@@ -474,8 +474,8 @@ static int cqhci_dma_map(struct mmc_host *host, struct mmc_request *mrq)return sg_count; } -static void cqhci_set_tran_desc (u8 *desc,dma_addr_t addr,int len,bool end, -bool dma64) +void cqhci_set_tran_desc (u8 *desc,dma_addr_t addr,int len,bool end, +bool dma64) {__le32 *attr = (__le32 __force *)desc;
@@ -495,6 +495,7 @@ static void cqhci_set_tran_desc(u8 *desc, dma_addr_t addr, int len, bool end, dataddr[0 ] =cpu_to_le32 (addr); } } +EXPORT_SYMBOL (cqhci_set_tran_desc);static int cqhci_prep_tran_desc (struct mmc_request *mrq,struct cqhci_host *cq_host,int tag)
@@ -522,7 +523,11 @@ static int cqhci_prep_tran_desc(struct mmc_request *mrq,if ((i+1 ) == sg_count) end = true; -cqhci_set_tran_desc (desc, addr, len, end, dma64); +if (cq_host->ops->set_tran_desc) + cq_host->ops->set_tran_desc (cq_host, &desc, addr, len, end, dma64); +else +cqhci_set_tran_desc (desc, addr, len, end, dma64); + desc += cq_host->trans_desc_len; }
drivers/mmc/host/cqhci.h +4 -0
@@ -293,6 +293,9 @@ struct cqhci_host_ops {int (*program_key)(struct cqhci_host *cq_host,const union cqhci_crypto_cfg_entry *cfg,int slot);#endif +void (*set_tran_desc)(struct cqhci_host *cq_host,u8 **desc, +dma_addr_t addr,int len,bool end,bool dma64); + };static inline void cqhci_writel (struct cqhci_host *host,u32 val,int reg)
@@ -318,6 +321,7 @@ irqreturn_t cqhci_irq(struct mmc_host *mmc, u32 intmask, int cmd_error,int cqhci_init (struct cqhci_host *cq_host,struct mmc_host *mmc,bool dma64);struct cqhci_host *cqhci_pltfm_init (struct platform_device *pdev);int cqhci_deactivate (struct mmc_host *mmc); +void cqhci_set_tran_desc (u8 *desc,dma_addr_t addr,int len,bool end,bool dma64);static inline int cqhci_suspend (struct mmc_host *mmc) {return cqhci_deactivate (mmc);
Signature · 1 line
2.30.2
Re: [PATCH v7 1/2] mmc: cqhci: Add cqhci set_tran_desc() callback
Quoted 7 lines · Sergey Khimich
From: Sergey Khimich <[email protected]>
There are could be specific limitations for some mmc controllers for setting cqhci transfer descriptors. So add callback to allow implement driver specific function.
Signed-off-by Sergey Khimich <[email protected]>
Quoted 63 lines
--- drivers/mmc/host/cqhci-core.c | 11 ++++++++--- drivers/mmc/host/cqhci.h | 4 ++++ 2 files changed, 12 insertions(+), 3 deletions(-)drivers/mmc/host/cqhci-core.c +8
-3@@ -474,8 +474,8 @@ static int cqhci_dma_map(struct mmc_host *host, struct mmc_request *mrq)return sg_count; } -static void cqhci_set_tran_desc (u8 *desc,dma_addr_t addr,int len,bool end, -bool dma64) +void cqhci_set_tran_desc (u8 *desc,dma_addr_t addr,int len,bool end, +bool dma64) {__le32 *attr = (__le32 __force *)desc;@@ -495,6 +495,7 @@ static void cqhci_set_tran_desc(u8 *desc, dma_addr_t addr, int len, bool end, dataddr[0 ] =cpu_to_le32 (addr); } } +EXPORT_SYMBOL (cqhci_set_tran_desc);static int cqhci_prep_tran_desc (struct mmc_request *mrq,struct cqhci_host *cq_host,int tag)@@ -522,7 +523,11 @@ static int cqhci_prep_tran_desc(struct mmc_request *mrq,if ((i+1 ) == sg_count) end = true; -cqhci_set_tran_desc (desc, addr, len, end, dma64); +if (cq_host->ops->set_tran_desc) + cq_host->ops->set_tran_desc (cq_host, &desc, addr, len, end, dma64); +else +cqhci_set_tran_desc (desc, addr, len, end, dma64); + desc += cq_host->trans_desc_len; }drivers/mmc/host/cqhci.h +4
-0@@ -293,6 +293,9 @@ struct cqhci_host_ops {int (*program_key)(struct cqhci_host *cq_host,const union cqhci_crypto_cfg_entry *cfg,int slot);#endif +void (*set_tran_desc)(struct cqhci_host *cq_host,u8 **desc, +dma_addr_t addr,int len,bool end,bool dma64); + };static inline void cqhci_writel (struct cqhci_host *host,u32 val,int reg)@@ -318,6 +321,7 @@ irqreturn_t cqhci_irq(struct mmc_host *mmc, u32 intmask, int cmd_error,int cqhci_init (struct cqhci_host *cq_host,struct mmc_host *mmc,bool dma64);struct cqhci_host *cqhci_pltfm_init (struct platform_device *pdev);int cqhci_deactivate (struct mmc_host *mmc); +void cqhci_set_tran_desc (u8 *desc,dma_addr_t addr,int len,bool end,bool dma64);static inline int cqhci_suspend (struct mmc_host *mmc) {return cqhci_deactivate (mmc);
PATCH v7 2/2 mmc: sdhci-of-dwcmshc: Implement SDHCI CQE support
In reply to Sergey KhimichFrom: Sergey Khimich <[email protected]>
For enabling CQE support just set 'supports-cqe' in your DevTree file for appropriate mmc node.
--- drivers/mmc/host/Kconfig | 1 + drivers/mmc/host/sdhci-of-dwcmshc.c | 191 +++++++++++++++++++++++++++- 2 files changed, 190 insertions(+), 2 deletions(-)
drivers/mmc/host/Kconfig +1 -0
@@ -233,6 +233,7 @@ config MMC_SDHCI_OF_DWCMSHC depends on MMC_SDHCI_PLTFM depends on OF depends on COMMON_CLK + select MMC_CQHCI help This selects Synopsys DesignWare Cores Mobile Storage Controller support.
drivers/mmc/host/sdhci-of-dwcmshc.c +189 -2
269 lines not on this page · raw message
Signature · 1 line
2.30.2
Re: [PATCH v7 2/2] mmc: sdhci-of-dwcmshc: Implement SDHCI CQE support
Quoted 6 lines · Sergey Khimich
From: Sergey Khimich <[email protected]>
For enabling CQE support just set 'supports-cqe' in your DevTree file for appropriate mmc node.
Signed-off-by Sergey Khimich <[email protected]>
Seems like it needs a re-base on latest mmc next, but nevertheless:
Quoted 303 lines
--- drivers/mmc/host/Kconfig | 1 + drivers/mmc/host/sdhci-of-dwcmshc.c | 191 +++++++++++++++++++++++++++- 2 files changed, 190 insertions(+), 2 deletions(-)drivers/mmc/host/Kconfig +1
-0@@ -233,6 +233,7 @@ config MMC_SDHCI_OF_DWCMSHC depends on MMC_SDHCI_PLTFM depends on OF depends on COMMON_CLK + select MMC_CQHCI help This selects Synopsys DesignWare Cores Mobile Storage Controller support.drivers/mmc/host/sdhci-of-dwcmshc.c +189
-2@@ -21,6 +21,7 @@#include <linux/sizes.h> #include "sdhci-pltfm.h" +#include "cqhci.h" #define SDHCI_DWCMSHC_ARG2_STUFF GENMASK(31, 16)@@ -52,6 +53,9 @@#define AT_CTRL_SWIN_TH_VAL_MASK GENMASK(31, 24)/* bits [31:24] */ #define AT_CTRL_SWIN_TH_VAL 0x9/* sampling window threshold */ +/* DWC IP vendor area 2 pointer */ +#define DWCMSHC_P_VENDOR_AREA2 0xea +/* Rockchip specific Registers */ #define DWCMSHC_EMMC_DLL_CTRL 0x800#define DWCMSHC_EMMC_DLL_RXCLK 0x804@@ -167,6 +171,10 @@#define BOUNDARY_OK (addr, len) \ ((addr | (SZ_128M - 1)) == ((addr + len - 1) | (SZ_128M - 1))) +#define DWCMSHC_SDHCI_CQE_TRNS_MODE (SDHCI_TRNS_MULTI | \ + SDHCI_TRNS_BLK_CNT_EN | \ + SDHCI_TRNS_DMA) +enum dwcmshc_rk_type {DWCMSHC_RK3568 ,DWCMSHC_RK3588 ,@@ -182,7 +190,9 @@ struct rk35xx_priv {struct dwcmshc_priv {struct clk *bus_clk; -int vendor_specific_area1;/* P_VENDOR_SPECIFIC_AREA reg */ +int vendor_specific_area1;/* P_VENDOR_SPECIFIC_AREA1 reg */ +int vendor_specific_area2;/* P_VENDOR_SPECIFIC_AREA2 reg */ +void *priv;/* pointer to SoC private stuff */ u16 delay_line;u16 flags;@@ -441,6 +451,90 @@ static void dwcmshc_hs400_enhanced_strobe(struct mmc_host *mmc,sdhci_writel (host, vendor, reg); } +static int dwcmshc_execute_tuning (struct mmc_host *mmc,u32 opcode) +{ +int err =sdhci_execute_tuning (mmc, opcode); +struct sdhci_host *host =mmc_priv (mmc); + +if (err) +return err; + +/* +* Tuning can leave the IP in an active state (Buffer Read Enable bit +* set) which prevents the entry to low power states (i.e. S0i3). Data +* reset will clear it. +*/ +sdhci_reset (host,SDHCI_RESET_DATA ); + +return 0 ; +} + +static u32 dwcmshc_cqe_irq_handler (struct sdhci_host *host,u32 intmask) +{ +int cmd_error =0 ; +int data_error =0 ; + +if (!sdhci_cqe_irq (host, intmask, &cmd_error, &data_error)) +return intmask; + +cqhci_irq (host->mmc, intmask, cmd_error, data_error); + +return 0 ; +} + +static void dwcmshc_sdhci_cqe_enable (struct mmc_host *mmc) +{ +struct sdhci_host *host =mmc_priv (mmc); +u8 ctrl; + +sdhci_writew (host,DWCMSHC_SDHCI_CQE_TRNS_MODE ,SDHCI_TRANSFER_MODE ); + +sdhci_cqe_enable (mmc); + +/* +* The "DesignWare Cores Mobile Storage Host Controller +* DWC_mshc / DWC_mshc_lite Databook" says: +* when Host Version 4 Enable" is 1 in Host Control 2 register, +* SDHCI_CTRL_ADMA32 bit means ADMA2 is selected. +* Selection of 32-bit/64-bit System Addressing: +* either 32-bit or 64-bit system addressing is selected by +* 64-bit Addressing bit in Host Control 2 register. +* +* On the other hand the "DesignWare Cores Mobile Storage Host +* Controller DWC_mshc / DWC_mshc_lite User Guide" says, that we have to +* set DMA_SEL to ADMA2 _only_ mode in the Host Control 2 register. +*/ + ctrl =sdhci_readb (host,SDHCI_HOST_CONTROL ); + ctrl &= ~SDHCI_CTRL_DMA_MASK ; + ctrl |=SDHCI_CTRL_ADMA32 ; +sdhci_writeb (host, ctrl,SDHCI_HOST_CONTROL ); +} + +static void dwcmshc_set_tran_desc (struct cqhci_host *cq_host,u8 **desc, +dma_addr_t addr,int len,bool end,bool dma64) +{ +int tmplen, offset; + +if (likely (!len ||BOUNDARY_OK (addr, len))) { +cqhci_set_tran_desc (*desc, addr, len, end, dma64); +return ; + } + + offset = addr & (SZ_128M -1 ); + tmplen =SZ_128M - offset; +cqhci_set_tran_desc (*desc, addr, tmplen, false, dma64); + + addr += tmplen; + len -= tmplen; + *desc += cq_host->trans_desc_len; +cqhci_set_tran_desc (*desc, addr, len, end, dma64); +} + +static void dwcmshc_cqhci_dumpregs (struct mmc_host *mmc) +{ +sdhci_dumpregs (mmc_priv (mmc)); +} +static void dwcmshc_rk3568_set_clock (struct sdhci_host *host,unsigned int clock) {struct sdhci_pltfm_host *pltfm_host =sdhci_priv (host);@@ -649,6 +743,7 @@ static const struct sdhci_ops sdhci_dwcmshc_ops = { .get_max_clock = dwcmshc_get_max_clock, .reset = sdhci_reset, .adma_write_desc = dwcmshc_adma_write_desc, + .irq = dwcmshc_cqe_irq_handler, };static const struct sdhci_ops sdhci_dwcmshc_rk35xx_ops = {@@ -700,6 +795,73 @@ static const struct sdhci_pltfm_data sdhci_dwcmshc_th1520_pdata = { .quirks2 = SDHCI_QUIRK2_PRESET_VALUE_BROKEN, }; +static const struct cqhci_host_ops dwcmshc_cqhci_ops = { + .enable = dwcmshc_sdhci_cqe_enable, + .disable = sdhci_cqe_disable, + .dumpregs = dwcmshc_cqhci_dumpregs, + .set_tran_desc = dwcmshc_set_tran_desc, +}; + +static void dwcmshc_cqhci_init (struct sdhci_host *host,struct platform_device *pdev) +{ +struct cqhci_host *cq_host; +struct sdhci_pltfm_host *pltfm_host =sdhci_priv (host); +struct dwcmshc_priv *priv =sdhci_pltfm_priv (pltfm_host); +bool dma64 = false; +u16 clk; +int err; + + host->mmc->caps2 |=MMC_CAP2_CQE |MMC_CAP2_CQE_DCMD ; + cq_host =devm_kzalloc (&pdev->dev,sizeof (*cq_host),GFP_KERNEL ); +if (!cq_host) { +dev_err (mmc_dev (host->mmc),"Unable to setup CQE: not enough memory\n" ); + goto dsbl_cqe_caps; + } + +/* +* For dwcmshc host controller we have to enable internal clock +* before access to some registers from Vendor Specific Area 2. +*/ + clk =sdhci_readw (host,SDHCI_CLOCK_CONTROL ); + clk |=SDHCI_CLOCK_INT_EN ; +sdhci_writew (host, clk,SDHCI_CLOCK_CONTROL ); + clk =sdhci_readw (host,SDHCI_CLOCK_CONTROL ); +if (!(clk &SDHCI_CLOCK_INT_EN )) { +dev_err (mmc_dev (host->mmc),"Unable to setup CQE: internal clock enable error\n" ); + goto free_cq_host; + } + + cq_host->mmio = host->ioaddr + priv->vendor_specific_area2; + cq_host->ops = &dwcmshc_cqhci_ops; + +/* Enable using of 128-bit task descriptors */ + dma64 = host->flags &SDHCI_USE_64_BIT_DMA ; +if (dma64) { +dev_dbg (mmc_dev (host->mmc),"128-bit task descriptors\n" ); + cq_host->caps |=CQHCI_TASK_DESC_SZ_128 ; + } + err =cqhci_init (cq_host, host->mmc, dma64); +if (err) { +dev_err (mmc_dev (host->mmc),"Unable to setup CQE: error %d\n" , err); + goto int_clock_disable; + } + +dev_dbg (mmc_dev (host->mmc),"CQE init done\n" ); + +return ; + +int_clock_disable: + clk =sdhci_readw (host,SDHCI_CLOCK_CONTROL ); + clk &= ~SDHCI_CLOCK_INT_EN ; +sdhci_writew (host, clk,SDHCI_CLOCK_CONTROL ); + +free_cq_host: +devm_kfree (&pdev->dev, cq_host); + +dsbl_cqe_caps: + host->mmc->caps2 &= ~(MMC_CAP2_CQE |MMC_CAP2_CQE_DCMD ); +} +static int dwcmshc_rk35xx_init (struct sdhci_host *host,struct dwcmshc_priv *dwc_priv) {int err;@@ -796,7 +958,7 @@ static int dwcmshc_probe(struct platform_device *pdev)struct rk35xx_priv *rk_priv =NULL ;const struct sdhci_pltfm_data *pltfm_data;int err; -u32 extra; +u32 extra, caps; pltfm_data =device_get_match_data (&pdev->dev);if (!pltfm_data) {@@ -847,6 +1009,7 @@ static int dwcmshc_probe(struct platform_device *pdev) host->mmc_host_ops.request = dwcmshc_request; host->mmc_host_ops.hs400_enhanced_strobe = dwcmshc_hs400_enhanced_strobe; + host->mmc_host_ops.execute_tuning = dwcmshc_execute_tuning;if (pltfm_data == &sdhci_dwcmshc_rk35xx_pdata) { rk_priv =devm_kzalloc (&pdev->dev,sizeof (struct rk35xx_priv ),GFP_KERNEL );@@ -896,6 +1059,10 @@ static int dwcmshc_probe(struct platform_device *pdev)sdhci_enable_v4_mode (host);#endif + caps =sdhci_readl (host,SDHCI_CAPABILITIES ); +if (caps &SDHCI_CAN_64BIT_V4 ) +sdhci_enable_v4_mode (host); + host->mmc->caps |=MMC_CAP_WAIT_WHILE_BUSY ;pm_runtime_get_noresume (dev);@@ -906,6 +1073,14 @@ static int dwcmshc_probe(struct platform_device *pdev)if (err) goto err_rpm; +/* Setup Command Queue Engine if enabled */ +if (device_property_read_bool (&pdev->dev,"supports-cqe" )) { + priv->vendor_specific_area2 = +sdhci_readw (host,DWCMSHC_P_VENDOR_AREA2 ); + +dwcmshc_cqhci_init (host, pdev); + } +if (rk_priv)dwcmshc_rk35xx_postinit (host, priv);@@ -961,6 +1136,12 @@ static int dwcmshc_suspend(struct device *dev)pm_runtime_resume (dev); +if (host->mmc->caps2 &MMC_CAP2_CQE ) { + ret =cqhci_suspend (host->mmc); +if (ret) +return ret; + } + ret =sdhci_suspend_host (host);if (ret)return ret;@@ -1005,6 +1186,12 @@ static int dwcmshc_resume(struct device *dev)if (ret) goto disable_rockchip_clks; +if (host->mmc->caps2 &MMC_CAP2_CQE ) { + ret =cqhci_resume (host->mmc); +if (ret) + goto disable_rockchip_clks; + } +return 0 ; disable_rockchip_clks:
Quoted 71 lines · Sergey Khimich
Hello!
This is implementation of SDHCI CQE support for sdhci-of-dwcmshc driver. For enabling CQE support just set 'supports-cqe' in your DevTree file for appropriate mmc node.
Also, while implementing CQE support for the driver, I faced with a problem which I will describe below.
According to the IP block documentation CQE works only with "AMDA-2 only" mode which is activated only with v4 mode enabled. I see indwcmshc_probe()function that v4 mode gets enabled only for 'sdhci_dwcmshc_bf3_pdata' platform data.So my question is: is it correct to enable v4 mode for all platform data if '
SDHCI_CAN_64BIT_V4' bit is set in hw?Because I`m afraid that enabling v4 mode for some platforms could break them down. On the other hand, if host controller says that it can do v4 (caps &
SDHCI_CAN_64BIT_V4), lets do v4 or disable it manualy by some quirk. Anyway - RFC.v2:
- Added dwcmshc specificcqe_disablehook to prevent losing in-flight cmd when an ioctl is issued andcqe_disableis called;- Added processing 128Mb boundary for the host memory data buffer size and the data buffer. For implementing this processing an extra callback is added to the struct '
sdhci_ops'.- Fixed typo.
v3:
- Fix warning reported by kernel test robot:| Reported-by: kernel test robot <[email protected]> | Closes: https://lore.kernel.org/oe-kbuild-all/[email protected]/ | Closes: https://lore.kernel.org/oe-kbuild-all/[email protected]/v4:
- Data reset moved to custom driver tuning hook.
- Removed unnecessarydwcmshc_sdhci_cqe_disable()func
- Removed unnecessarydwcmshc_cqhci_set_tran_desc. Export and usecqhci_set_tran_desc()instead.
- Provide a hook forcqhci_set_tran_desc()instead ofcqhci_prep_tran_desc().
- Fix typo:int_clok_disable-->int_clock_disablev5:
- Fix warning reported by kernel test robot:
| Reported-by: kernel test robot <[email protected]>
| Closes: https://lore.kernel.org/oe-kbuild-all/[email protected]/v6:
- Rebase to master branch
- Fix typo;
- Fix double blank line;
- Addcqhci_suspend()andcqhci_resume()functions
to support mmc suspend-to-ram (s2r);
- Move readingDWCMSHC_P_VENDOR_AREA2register under "supports-cqe" condition as not all IPs have that register;
- Remove sdhci V4 mode from the list of prerequisites to init cqhci.v7:
- Add disablingMMC_CAP2_CQEandMMC_CAP2_CQE_DCMDcaps in case of CQE init fails to prevent problems in suspend/resume functions.Sergey Khimich (2):
mmc: cqhci: Add cqhciset_tran_desc()callback
mmc: sdhci-of-dwcmshc: Implement SDHCI CQE support
Quoted 6 lines
drivers/mmc/host/Kconfig | 1 + drivers/mmc/host/cqhci-core.c | 11 +- drivers/mmc/host/cqhci.h | 4 + drivers/mmc/host/sdhci-of-dwcmshc.c | 191 +++++++++++++++++++++++++++- 4 files changed, 202 insertions(+), 5 deletions(-)
Applied for next and by fixing a minor conflict when applying, thanks!
Kind regards
Uffe