ARM: imx_v6_v7_defconfig: Select CONFIG_USB_ONBOARD_HUB
Subsystems (3)
Fabio Estevam
reviewerPATCH 1/2 ARM: imx_v6_v7_defconfig: Select CONFIG_USB_ONBOARD_HUB
From: Fabio Estevam <[email protected]>
The imx6qdl-udoo board has a USB2514 Hub connected to the USB Host1 port.
Select CONFIG_USB_ONBOARD_HUB so that USB hub can be functional.
--- arch/arm/configs/imx_v6_v7_defconfig | 1 + 1 file changed, 1 insertion(+)
arch/arm/configs/imx_v6_v7_defconfig +1 -0
@@ -336,6 +336,7 @@ CONFIG_USB_SERIAL_FTDI_SIO=m CONFIG_USB_SERIAL_OPTION=m CONFIG_USB_TEST=m CONFIG_USB_EHSET_TEST_FIXTURE=m +CONFIG_USB_ONBOARD_HUB=y CONFIG_NOP_USB_XCEIV=y CONFIG_USB_MXS_PHY=y CONFIG_USB_GADGET=y
Signature · 7 lines
2.34.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Fabio Estevam
reviewerPATCH 2/2 ARM: dts: imx6qdl-udoo: Enable USB host
From: Fabio Estevam <[email protected]>
Commit 8f2ca252ee1f ("ARM: dts: imx6qdl-udoo: Disable USB host to work around boot issues") disabled USB host to avoid boot hang.
Properly describe the USB2514 USB hub to fix this issue.
Tested on a imx6q-udoo board and verified that it boots fine and USB host functionality works.
--- arch/arm/boot/dts/nxp/imx/imx6qdl-udoo.dtsi | 25 ++++++++++----------- 1 file changed, 12 insertions(+), 13 deletions(-)
arch/arm/boot/dts/nxp/imx/imx6qdl-udoo.dtsi +12 -13
@@ -59,16 +59,6 @@ panel_in: endpoint { }; }; - reg_usb_h1_vbus: regulator-usb-h1-vbus { - compatible = "regulator-fixed"; - regulator-name = "usb_h1_vbus"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - startup-delay-us = <2>; /* USB2415 requires a POR of 1 us minimum */ - gpio = <&gpio7 12 0>; - }; - reg_panel: regulator-panel { compatible = "regulator-fixed"; regulator-name = "lcd_panel";
@@ -285,9 +275,18 @@ &uart4 { &usbh1 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usbh>; - vbus-supply = <®_usb_h1_vbus>; - clocks = <&clks IMX6QDL_CLK_CKO>; - status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + usb-port@1 { + compatible = "usb424,2514"; + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clks IMX6QDL_CLK_CKO>; + reset-gpios = <&gpio7 12 GPIO_ACTIVE_LOW>; + }; }; &usbotg {
Signature · 7 lines
2.34.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Shawn Guo
AppliedQuoted 8 lines · Fabio Estevam
From: Fabio Estevam <[email protected]>
The imx6qdl-udoo board has a USB2514 Hub connected to the USB Host1 port.
Select
CONFIG_USB_ONBOARD_HUBso that USB hub can be functional.Signed-off-by Fabio Estevam <[email protected]>
Applied both, thanks!
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel