HID: i2c-hid: Revert to await reset ACK before reading report descriptor
Subsystems (2)
PATCH v3 1/1 HID: i2c-hid: Revert to await reset ACK before reading report descriptor
From: Kenny Levinsen <[email protected]>
In af93a167eda9, i2c_hid_parse was changed to continue with reading the report descriptor before waiting for reset to be acknowledged.
This has lead to two regressions:
1. We fail to handle reset acknowledgment if it happens while reading the report descriptor. The transfer sets I2C_HID_READ_PENDING, which causes the IRQ handler to return without doing anything.
This affects both a Wacom touchscreen and a Sensel touchpad.
2. On a Sensel touchpad, reading the report descriptor this quickly after reset results in all zeroes or partial zeroes.
The issues were observed on the Lenovo Thinkpad Z16 Gen 2.
The change in question was made based on a Microsoft article[0] stating that Windows 8 *may* read the report descriptor in parallel with awaiting reset acknowledgment, intended as a slight reset performance optimization. Perhaps they only do this if reset is not completing quickly enough for their tastes?
As the code is not currently ready to read registers in parallel with a pending reset acknowledgment, and as reading quickly breaks the report descriptor on the Sensel touchpad, revert to waiting for reset acknowledgment before proceeding to read the report descriptor.
--- drivers/hid/i2c-hid/i2c-hid-core.c | 29 ++++++++--------------------- 1 file changed, 8 insertions(+), 21 deletions(-)
drivers/hid/i2c-hid/i2c-hid-core.c +8 -21
@@ -735,12 +735,15 @@ static int i2c_hid_parse(struct hid_device *hid)mutex_lock (&ihid->reset_lock);do { ret =i2c_hid_start_hwreset (ihid); -if (ret) +if (ret ==0 ) + ret =i2c_hid_finish_hwreset (ihid); +else msleep (1000 ); }while (tries-- >0 && ret); +mutex_unlock (&ihid->reset_lock);if (ret) - goto abort_reset; +return ret; use_override =i2c_hid_get_dmi_hid_report_desc_override (client->name, &rsize);
@@ -750,11 +753,8 @@ static int i2c_hid_parse(struct hid_device *hid)i2c_hid_dbg (ihid,"Using a HID report descriptor override\n" ); }else { rdesc =kzalloc (rsize,GFP_KERNEL ); - -if (!rdesc) { - ret = -ENOMEM ; - goto abort_reset; - } +if (!rdesc) +return -ENOMEM ;i2c_hid_dbg (ihid,"asking HID report descriptor\n" );
@@ -763,23 +763,10 @@ static int i2c_hid_parse(struct hid_device *hid) rdesc, rsize);if (ret) {hid_err (hid,"reading report descriptor failed\n" ); - goto abort_reset; + goto out; } } -/* -* Windows directly reads the report-descriptor after sending reset -* and then waits for resets completion afterwards. Some touchpads -* actually wait for the report-descriptor to be read before signalling -* reset completion. -*/ - ret =i2c_hid_finish_hwreset (ihid); -abort_reset: -clear_bit (I2C_HID_RESET_PENDING , &ihid->flags); -mutex_unlock (&ihid->reset_lock); -if (ret) - goto out; -i2c_hid_dbg (ihid,"Report Descriptor: %*ph\n" , rsize, rdesc); ret =hid_parse_report (hid, rdesc, rsize);
Signature · 1 line
2.44.0
Quoted 97 lines · Hans de Goede
From: Kenny Levinsen <[email protected]>
In
af93a167eda9,i2c_hid_parsewas changed to continue with reading the report descriptor before waiting for reset to be acknowledged.This has lead to two regressions:
1. We fail to handle reset acknowledgment if it happens while reading the report descriptor. The transfer sets
I2C_HID_READ_PENDING, which causes the IRQ handler to return without doing anything.This affects both a Wacom touchscreen and a Sensel touchpad.
2. On a Sensel touchpad, reading the report descriptor this quickly after reset results in all zeroes or partial zeroes.
The issues were observed on the Lenovo Thinkpad Z16 Gen 2.
The change in question was made based on a Microsoft article[0] stating that Windows 8 *may* read the report descriptor in parallel with awaiting reset acknowledgment, intended as a slight reset performance optimization. Perhaps they only do this if reset is not completing quickly enough for their tastes?
As the code is not currently ready to read registers in parallel with a pending reset acknowledgment, and as reading quickly breaks the report descriptor on the Sensel touchpad, revert to waiting for reset acknowledgment before proceeding to read the report descriptor.
Fixes af93a167eda9 ("HID: i2c-hid: Move i2c_hid_finish_hwreset() toafter reading the report-descriptor")
Signed-off-by Kenny Levinsen <[email protected]>[[email protected] Drop no longer necessary
abort_reseterror exit path]Signed-off-by Hans de Goede <[email protected]>--- drivers/hid/i2c-hid/i2c-hid-core.c | 29 ++++++++--------------------- 1 file changed, 8 insertions(+), 21 deletions(-)drivers/hid/i2c-hid/i2c-hid-core.c +8
-14@@ -735,12 +735,15 @@ static int i2c_hid_parse(struct hid_device *hid)mutex_lock (&ihid->reset_lock);do { ret =i2c_hid_start_hwreset (ihid); -if (ret) +if (ret ==0 ) + ret =i2c_hid_finish_hwreset (ihid); +else msleep (1000 ); }while (tries-- >0 && ret); +mutex_unlock (&ihid->reset_lock);if (ret) - goto abort_reset; +return ret; use_override =i2c_hid_get_dmi_hid_report_desc_override (client->name, &rsize);@@ -750,11 +753,8 @@ static int i2c_hid_parse(struct hid_device *hid)i2c_hid_dbg (ihid,"Using a HID report descriptor override\n" ); }else { rdesc =kzalloc (rsize,GFP_KERNEL ); - -if (!rdesc) { - ret = -ENOMEM ; - goto abort_reset; - } +if (!rdesc) +return -ENOMEM ;i2c_hid_dbg (ihid,"asking HID report descriptor\n" );@@ -763,23 +763,10 @@ static int i2c_hid_parse(struct hid_device *hid) rdesc, rsize);if (ret) {hid_err (hid,"reading report descriptor failed\n" ); - goto abort_reset; + goto out; } } -/* -* Windows directly reads the report-descriptor after sending reset -* and then waits for resets completion afterwards. Some touchpads -* actually wait for the report-descriptor to be read before signalling -* reset completion. -*/
drivers/hid/i2c-hid/i2c-hid-core.c static int i2c_hid_parse(struct hid_device *hid) · line 772
Quoted 10 lines
drivers/hid/i2c-hid/i2c-hid-core.c +0
-7- ret =i2c_hid_finish_hwreset (ihid); -abort_reset: -clear_bit (I2C_HID_RESET_PENDING , &ihid->flags); -mutex_unlock (&ihid->reset_lock); -if (ret) - goto out; -i2c_hid_dbg (ihid,"Report Descriptor: %*ph\n" , rsize, rdesc); ret =hid_parse_report (hid, rdesc, rsize);
Tested on my Z13 G2 system and confirmed this fixes the issue.
Quoted 42 lines · Mark Pearson
Quoted 41 lines · Hans de Goede
From: Kenny Levinsen <[email protected]>
In
af93a167eda9,i2c_hid_parsewas changed to continue with reading the report descriptor before waiting for reset to be acknowledged.This has lead to two regressions:
1. We fail to handle reset acknowledgment if it happens while reading the report descriptor. The transfer sets
I2C_HID_READ_PENDING, which causes the IRQ handler to return without doing anything.This affects both a Wacom touchscreen and a Sensel touchpad.
2. On a Sensel touchpad, reading the report descriptor this quickly after reset results in all zeroes or partial zeroes.
The issues were observed on the Lenovo Thinkpad Z16 Gen 2.
The change in question was made based on a Microsoft article[0] stating that Windows 8 *may* read the report descriptor in parallel with awaiting reset acknowledgment, intended as a slight reset performance optimization. Perhaps they only do this if reset is not completing quickly enough for their tastes?
As the code is not currently ready to read registers in parallel with a pending reset acknowledgment, and as reading quickly breaks the report descriptor on the Sensel touchpad, revert to waiting for reset acknowledgment before proceeding to read the report descriptor.
Fixes af93a167eda9 ("HID: i2c-hid: Move i2c_hid_finish_hwreset() toafter reading the report-descriptor")
Signed-off-by Kenny Levinsen <[email protected]>[[email protected] Drop no longer necessary
abort_reseterror exit path]Signed-off-by Hans de Goede <[email protected]>
[ .. snip .. ]
Quoted 3 lines
Tested on my Z13 G2 system and confirmed this fixes the issue.
Tested-by Mark Pearson <[email protected]>
Applied to hid.git#for-6.9/upstream-fixes. Thanks,
Signature · 2 lines
Jiri Kosina SUSE Labs