Skip to contentSkip to conversation

scsi: aic7xxx: indent kconfig help text

PATCH Applied Prasad Pandit 2 participants 2 messages Apr 8, 2024 – Apr 12, 2024

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 scsi: aic7xxx: indent kconfig help text

From: Prasad Pandit <[email protected]>

Fix indentation of config option's help text by adding leading spaces. Generally help text is indented by two more spaces beyond the leading tab <\t> character. It helps Kconfig parsers to read file without error.

---
 drivers/scsi/aic7xxx/Kconfig.aic79xx | 75 ++++++++++-----------
 drivers/scsi/aic7xxx/Kconfig.aic7xxx | 97 ++++++++++++++--------------
 2 files changed, 87 insertions(+), 85 deletions(-)
drivers/scsi/aic7xxx/Kconfig.aic79xx +38 -37
index 4bc53eec4c83..863f0932ef59 100644
@@ -8,79 +8,80 @@ config SCSI_AIC79XX
 	depends on PCI && HAS_IOPORT && SCSI
 	select SCSI_SPI_ATTRS
 	help
-	This driver supports all of Adaptec's Ultra 320 PCI-X
-	based SCSI controllers.
+	  This driver supports all of Adaptec's Ultra 320 PCI-X
+	  based SCSI controllers.
 
 config AIC79XX_CMDS_PER_DEVICE
 	int "Maximum number of TCQ commands per device"
 	depends on SCSI_AIC79XX
 	default "32"
 	help
-	Specify the number of commands you would like to allocate per SCSI
-	device when Tagged Command Queueing (TCQ) is enabled on that device.
+	  Specify the number of commands you would like to allocate per SCSI
+	  device when Tagged Command Queueing (TCQ) is enabled on that device.
 
-	This is an upper bound value for the number of tagged transactions
-	to be used for any device.  The aic7xxx driver will automatically
-	vary this number based on device behavior.  For devices with a
-	fixed maximum, the driver will eventually lock to this maximum
-	and display a console message indicating this value.
+	  This is an upper bound value for the number of tagged transactions
+	  to be used for any device.  The aic7xxx driver will automatically
+	  vary this number based on device behavior.  For devices with a
+	  fixed maximum, the driver will eventually lock to this maximum
+	  and display a console message indicating this value.
 
-	Due to resource allocation issues in the Linux SCSI mid-layer, using
-	a high number of commands per device may result in memory allocation
-	failures when many devices are attached to the system.  For this reason,
-	the default is set to 32.  Higher values may result in higher performance
-	on some devices.  The upper bound is 253.  0 disables tagged queueing.
+	  Due to resource allocation issues in the Linux SCSI mid-layer, using
+	  a high number of commands per device may result in memory allocation
+	  failures when many devices are attached to the system.  For this
+	  reason, the default is set to 32. Higher values may result in higher
+	  performance on some devices. The upper bound is 253. 0 disables
+	  tagged queueing.
 
-	Per device tag depth can be controlled via the kernel command line
-	"tag_info" option.  See Documentation/scsi/aic79xx.rst for details.
+	  Per device tag depth can be controlled via the kernel command line
+	  "tag_info" option.  See Documentation/scsi/aic79xx.rst for details.
 
 config AIC79XX_RESET_DELAY_MS
 	int "Initial bus reset delay in milli-seconds"
 	depends on SCSI_AIC79XX
 	default "5000"
 	help
-	The number of milliseconds to delay after an initial bus reset.
-	The bus settle delay following all error recovery actions is
-	dictated by the SCSI layer and is not affected by this value.
+	  The number of milliseconds to delay after an initial bus reset.
+	  The bus settle delay following all error recovery actions is
+	  dictated by the SCSI layer and is not affected by this value.
 
-	Default: 5000 (5 seconds)
+	  Default: 5000 (5 seconds)
 
 config AIC79XX_BUILD_FIRMWARE
 	bool "Build Adapter Firmware with Kernel Build"
 	depends on SCSI_AIC79XX && !PREVENT_FIRMWARE_BUILD
 	help
-	This option should only be enabled if you are modifying the firmware
-	source to the aic79xx driver and wish to have the generated firmware
-	include files updated during a normal kernel build.  The assembler
-	for the firmware requires lex and yacc or their equivalents, as well
-	as the db v1 library.  You may have to install additional packages
-	or modify the assembler Makefile or the files it includes if your
-	build environment is different than that of the author.
+	  This option should only be enabled if you are modifying the firmware
+	  source to the aic79xx driver and wish to have the generated firmware
+	  include files updated during a normal kernel build.  The assembler
+	  for the firmware requires lex and yacc or their equivalents, as well
+	  as the db v1 library.  You may have to install additional packages
+	  or modify the assembler Makefile or the files it includes if your
+	  build environment is different than that of the author.
 
 config AIC79XX_DEBUG_ENABLE
 	bool "Compile in Debugging Code"
 	depends on SCSI_AIC79XX
 	default y
 	help
-	Compile in aic79xx debugging code that can be useful in diagnosing
-	driver errors.
+	  Compile in aic79xx debugging code that can be useful in diagnosing
+	  driver errors.
 
 config AIC79XX_DEBUG_MASK
 	int "Debug code enable mask (16383 for all debugging)"
 	depends on SCSI_AIC79XX
 	default "0"
 	help
-	Bit mask of debug options that is only valid if the
-	CONFIG_AIC79XX_DEBUG_ENABLE option is enabled.  The bits in this mask
-	are defined in the drivers/scsi/aic7xxx/aic79xx.h - search for the
-	variable ahd_debug in that file to find them.
+	  Bit mask of debug options that is only valid if the
+	  CONFIG_AIC79XX_DEBUG_ENABLE option is enabled.  The bits in this mask
+	  are defined in the drivers/scsi/aic7xxx/aic79xx.h - search for the
+	  variable ahd_debug in that file to find them.
 
 config AIC79XX_REG_PRETTY_PRINT
 	bool "Decode registers during diagnostics"
 	depends on SCSI_AIC79XX
 	default y
 	help
-	Compile in register value tables for the output of expanded register
-	contents in diagnostics.  This make it much easier to understand debug
-	output without having to refer to a data book and/or the aic7xxx.reg
-	file.
+	  Compile in register value tables for the output of expanded register
+	  contents in diagnostics.  This make it much easier to understand debug
+	  output without having to refer to a data book and/or the aic7xxx.reg
+	  file.
drivers/scsi/aic7xxx/Kconfig.aic7xxx +49 -48

133 lines not on this page · raw message

Signature · 1 line
2.44.0
#1 lore raw
Quoted 6 lines · Prasad Pandit

Fix indentation of config option's help text by adding leading spaces. Generally help text is indented by two more spaces beyond the leading tab <\t> character. It helps Kconfig parsers to read file without error.

Applied to 6.10/scsi-queue, thanks!

[1/1] scsi: aic7xxx: indent kconfig help text

      https://git.kernel.org/mkp/scsi/c/6c19ecf4ad1d
Signature · 1 line
Martin K. Petersen	Oracle Linux Engineering