Skip to contentSkip to conversation

media: dt-bindings: nxp,imx8-jpeg: Add clocks entries

PATCH In review Mirela Rabulea 3 participants 5 messages Apr 8, 2024 – Apr 22, 2024

Subsystems (4)
lore
Share & tools
lore

Mirela Rabulea

author maintainer
#0 lore raw

PATCH v6 1/2 media: dt-bindings: nxp,imx8-jpeg: Add clocks entries

From: Fabio Estevam <[email protected]>

The JPEG decoder/encoder present in iMX8QXP and iMX8QM SoCs need the PER and IPG clocks to be functional, so add the clock entries.

This also fixes the following schema warning:

imx8qm-apalis-eval.dtb: jpegdec@58400000: 'assigned-clock-rates', 'assigned-clocks', 'clock-names', 'clocks' do not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/media/nxp,imx8-jpeg.yaml#

---
Changes since v5:
- Remove one extra ":" from subject (thanks Fabio!)
- Use <[email protected]> address for both Author and Signed-of (Fabio's feedback)

Changes since v4:
- Remove redundant description and update subject prefix (per Krzysztof's feddback)

Changes since v3:
- Add items for clocks (per Krzysztof's feddback)
- Add description for clocks (per Conor's feddback to the other similar patch from Alexander)
- Add "media:" to the subject
- Add Mirela's signed-off
- For the similar patches that were sent for this issue, should Co-developed-by/Signed-off-by be added? Alexander Stein? Frank Li?

Changes since v2:
- Remove clock-names. (Mirela)

 .../devicetree/bindings/media/nxp,imx8-jpeg.yaml      | 11 +++++++++++
 1 file changed, 11 insertions(+)
Documentation/devicetree/bindings/media/nxp,imx8-jpeg.yaml +11 -0
index 3d9d1db37040..2be30c5fdc83 100644
@@ -31,6 +31,11 @@ properties:
   reg:
     maxItems: 1
 
+  clocks:
+    items:
+      - description: AXI DMA engine clock for fetching JPEG bitstream from memory (per)
+      - description: IP bus clock for register access (ipg)
+
   interrupts:
     description: |
       There are 4 slots available in the IP, which the driver may use
@@ -49,6 +54,7 @@ properties:
 required:
   - compatible
   - reg
+  - clocks
   - interrupts
   - power-domains
 
@@ -56,12 +62,15 @@ additionalProperties: false
 
 examples:
   - |
+    #include <dt-bindings/clock/imx8-lpcg.h>
     #include <dt-bindings/interrupt-controller/arm-gic.h>
     #include <dt-bindings/firmware/imx/rsrc.h>
 
     jpegdec: jpegdec@58400000 {
         compatible = "nxp,imx8qxp-jpgdec";
         reg = <0x58400000 0x00050000 >;
+        clocks = <&img_jpeg_dec_lpcg IMX_LPCG_CLK_0>,
+                 <&img_jpeg_dec_lpcg IMX_LPCG_CLK_4>;
         interrupts = <GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH>,
                      <GIC_SPI 310 IRQ_TYPE_LEVEL_HIGH>,
                      <GIC_SPI 311 IRQ_TYPE_LEVEL_HIGH>,
@@ -76,6 +85,8 @@ examples:
     jpegenc: jpegenc@58450000 {
         compatible = "nxp,imx8qm-jpgenc", "nxp,imx8qxp-jpgenc";
         reg = <0x58450000 0x00050000 >;
+        clocks = <&img_jpeg_enc_lpcg IMX_LPCG_CLK_0>,
+                 <&img_jpeg__lpcg IMX_LPCG_CLK_4>;
         interrupts = <GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>,
                      <GIC_SPI 306 IRQ_TYPE_LEVEL_HIGH>,
                      <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>,
Signature · 1 line
2.25.1
author maintainer
#1 lore raw

PATCH v6 2/2 arm64: dts: imx8-ss-img: Remove JPEG clock-names

From: Fabio Estevam <[email protected]>

Per nxp,imx8-jpeg.yaml, the clock-names entry is not valid.

Remove them.

---
Changes since v5:
- Use <[email protected]> address for both Author and Signed-of (Fabio's feedback) Changes since v4:
- None
Changes since v3:
- Just added "imx8-ss-img:" in the subject

Changes since v2:
- Newly introduced.

 arch/arm64/boot/dts/freescale/imx8-ss-img.dtsi | 2 --
 1 file changed, 2 deletions(-)
arch/arm64/boot/dts/freescale/imx8-ss-img.dtsi +0 -2
index e7783cc2d830..77d2928997b4 100644
@@ -21,7 +21,6 @@ jpegdec: jpegdec@58400000 {
 		interrupts = <GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&img_jpeg_dec_lpcg IMX_LPCG_CLK_0>,
 			 <&img_jpeg_dec_lpcg IMX_LPCG_CLK_4>;
-		clock-names = "per", "ipg";
 		assigned-clocks = <&img_jpeg_dec_lpcg IMX_LPCG_CLK_0>,
 				  <&img_jpeg_dec_lpcg IMX_LPCG_CLK_4>;
 		assigned-clock-rates = <200000000>, <200000000>;
@@ -35,7 +34,6 @@ jpegenc: jpegenc@58450000 {
 		interrupts = <GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&img_jpeg_enc_lpcg IMX_LPCG_CLK_0>,
 			 <&img_jpeg_enc_lpcg IMX_LPCG_CLK_4>;
-		clock-names = "per", "ipg";
 		assigned-clocks = <&img_jpeg_enc_lpcg IMX_LPCG_CLK_0>,
 				  <&img_jpeg_enc_lpcg IMX_LPCG_CLK_4>;
 		assigned-clock-rates = <200000000>, <200000000>;
Signature · 1 line
2.25.1
#2 lore raw

Re: [PATCH v6 2/2] arm64: dts: imx8-ss-img: Remove JPEG clock-names

Quoted 7 lines · Mirela Rabulea

From: Fabio Estevam <[email protected]>

Per nxp,imx8-jpeg.yaml, the clock-names entry is not valid.

Remove them.

When you forward a patch from someone else, you should add your SoB. I fixed it up and applied the patch.

Shawn

#3 lore raw
In reply to Mirela Rabulea
Quoted 5 lines · Mirela Rabulea

From: Fabio Estevam <[email protected]>

The JPEG decoder/encoder present in iMX8QXP and iMX8QM SoCs need the PER and IPG clocks to be functional, so add the clock entries.

Quoted 8 lines

This also fixes the following schema warning:

imx8qm-apalis-eval.dtb: jpegdec@58400000: 'assigned-clock-rates', 'assigned-clocks', 'clock-names', 'clocks' do not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/media/nxp,imx8-jpeg.yaml#

---

This is like third version today? Give people chance to review your code and wait 24h before postings.

Best regards,
Krzysztof

Reviewed-by on v6 1/2
#4 lore raw
In reply to Mirela Rabulea
Quoted 5 lines · Mirela Rabulea

From: Fabio Estevam <[email protected]>

The JPEG decoder/encoder present in iMX8QXP and iMX8QM SoCs need the PER and IPG clocks to be functional, so add the clock entries.

Quoted 8 lines

This also fixes the following schema warning:

imx8qm-apalis-eval.dtb: jpegdec@58400000: 'assigned-clock-rates', 'assigned-clocks', 'clock-names', 'clocks' do not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/media/nxp,imx8-jpeg.yaml#

---

---

This is an automated instruction, just in case, because many review tags are being ignored. If you know the process, you can skip it (please do not feel offended by me posting it here - no bad intentions intended). If you do not know the process, here is a short explanation:

Please add Acked-by/Reviewed-by/Tested-by tags when posting new versions, under or above your Signed-off-by tag. Tag is "received", when provided in a message replied to you on the mailing list. Tools like b4 can help here. However, there's no need to repost patches *only* to add the tags. The upstream maintainer will do that for tags received on the version they apply.

https://elixir.bootlin.com/linux/v6.5-rc3/source/Documentation/process/submitting-patches.rst#L577

Best regards,
Krzysztof