LVDS Controller Support for SAM9X75 SoC
Subsystems (7)
Dharma Balasubiramani
maintainerv8 cover LVDS Controller Support for SAM9X75 SoC
This patch series introduces LVDS controller support for the SAM9X75 SoC. The LVDS controller is designed to work with Microchip's sam9x7 series System-on-Chip (SoC) devices, providing Low Voltage Differential Signaling capabilities.
Patch series Changelog:
- Include configs: at91: Enable LVDS serializer
- include all necessary To/Cc entries.
The Individual Changelogs are available on the respective patches.
Dharma Balasubiramani (4):
dt-bindings: display: bridge: add sam9x75-lvds binding drm/bridge: add lvds controller support for sam9x7
MAINTAINERS: add SAM9X7 SoC's LVDS controller
ARM: configs: at91: Enable LVDS serializer support
.../bridge/microchip,sam9x75-lvds.yaml | 55 +++++ MAINTAINERS | 8 + arch/arm/configs/at91_dt_defconfig | 1 + drivers/gpu/drm/bridge/Kconfig | 7 + drivers/gpu/drm/bridge/Makefile | 1 + drivers/gpu/drm/bridge/microchip-lvds.c | 229 ++++++++++++++++++ 6 files changed, 301 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/bridge/microchip,sam9x75-lvds.yaml create mode 100644 drivers/gpu/drm/bridge/microchip-lvds.c
Signature · 1 line
2.25.1
Dharma Balasubiramani
maintainerPATCH v8 1/4 dt-bindings: display: bridge: add sam9x75-lvds binding
Add the 'sam9x75-lvds' compatible binding, which describes the Low Voltage Differential Signaling (LVDS) Controller found on some Microchip's sam9x7 series System-on-Chip (SoC) devices. This binding will be used to define the properties and configuration for the LVDS Controller in DT.
---
Changelog
v7 -> v8
v6 -> v7
v5 -> v6
v4 -> v5
- No changes.
v3 -> v4
- Rephrase the commit subject.
v2 -> v3
- No changes.
v1 -> v2
- Remove '|' in description, as there is no formatting to preserve.
- Remove 'gclk' from clock-names as there is only one clock(pclk).
- Remove the unused headers and include only used ones.
- Change the compatible name specific to SoC (sam9x75) instead of entire series.
- Change file name to match the compatible name.
--- .../bridge/microchip,sam9x75-lvds.yaml | 55 +++++++++++++++++++ 1 file changed, 55 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/bridge/microchip,sam9x75-lvds.yaml
Documentation/devicetree/bindings/display/bridge/microchip,sam9x75-lvds.yaml new file +55 -0
@@ -0,0 +1,55 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/bridge/microchip,sam9x75-lvds.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Microchip SAM9X75 LVDS Controller + +maintainers: + - Dharma Balasubiramani <[email protected]> + +description: + The Low Voltage Differential Signaling Controller (LVDSC) manages data + format conversion from the LCD Controller internal DPI bus to OpenLDI + LVDS output signals. LVDSC functions include bit mapping, balanced mode + management, and serializer. + +properties: + compatible: + const: microchip,sam9x75-lvds + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + items: + - description: Peripheral Bus Clock + + clock-names: + items: + - const: pclk + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/clock/at91.h> + lvds-controller@f8060000 { + compatible = "microchip,sam9x75-lvds"; + reg = <0xf8060000 0x100>; + interrupts = <56 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 56>; + clock-names = "pclk"; + };
Signature · 1 line
2.25.1
Dharma Balasubiramani
maintainerPATCH v8 2/4 drm/bridge: add lvds controller support for sam9x7
In reply to Dharma BalasubiramaniAdd a new LVDS controller driver for sam9x7 which does the following:
- Prepares and enables the LVDS Peripheral clock
- Defines its connector type as DRM_MODE_CONNECTOR_LVDS and adds itself to the global bridge list.
- Identifies its output endpoint as panel and adds it to the encoder display pipeline
- Enables the LVDS serializer
---
Changelog
v7 -> v8
- Assign ret variable properly before checking it for err.
v6 -> v7
- Remove setting encoder type from bridge driver.
- Drop clk_disable() from pm_runtime_get_sync() error handling.
- Use devm_clk_get() instead of prepared version.
- Hence use clk_prepare_enable() and clk_disable_unprepare().
- Use devm_drm_of_get_bridge() instead of devm_drm_panel_bridge_add().
- Add error check for devm_pm_runtime_enable().
- Use dev_err() instead of DRM_DEV_ERROR() as it is deprecated.
- Add missing Acked-by tag.
v5 -> v6
- No Changes.
v4 -> v5
- Drop the unused variable 'format'.
- Use DRM wrapper for dev_err() to maintain uniformity.
- return -ENODEV instead of -EINVAL to maintain consistency with other DRM bridge drivers.
v3 -> v4
- No changes.
v2 ->v3
- Correct Typo error "serializer".
- Consolidate get() and prepare() functions and use devm_clk_get_prepared().
- Remove unused variable 'ret' in probe().
- Use devm_pm_runtime_enable() and drop the mchp_lvds_remove(). v1 -> v2
- Drop 'res' variable and combine two lines into one.
- Handle deferred probe properly, use dev_err_probe().
- Don't print anything on deferred probe. Dropped print.
- Remove the MODULE_ALIAS and add MODULE_DEVICE_TABLE().
- symbol 'mchp_lvds_driver' was not declared. It should be static.
--- drivers/gpu/drm/bridge/Kconfig | 7 + drivers/gpu/drm/bridge/Makefile | 1 + drivers/gpu/drm/bridge/microchip-lvds.c | 229 ++++++++++++++++++++++++ 3 files changed, 237 insertions(+) create mode 100644 drivers/gpu/drm/bridge/microchip-lvds.c
drivers/gpu/drm/bridge/Kconfig +7 -0
@@ -190,6 +190,13 @@ config DRM_MEGACHIPS_STDPXXXX_GE_B850V3_FW to DP++. This is used with the i.MX6 imx-ldb driver. You are likely to say N here. +config DRM_MICROCHIP_LVDS_SERIALIZER + tristate "Microchip LVDS serializer support" + depends on OF + depends on DRM_ATMEL_HLCDC + help + Support for Microchip's LVDS serializer. + config DRM_NWL_MIPI_DSI tristate "Northwest Logic MIPI DSI Host controller" depends on DRM
drivers/gpu/drm/bridge/Makefile +1 -0
@@ -13,6 +13,7 @@ obj-$(CONFIG_DRM_LONTIUM_LT9611) += lontium-lt9611.o obj-$(CONFIG_DRM_LONTIUM_LT9611UXC) += lontium-lt9611uxc.o obj-$(CONFIG_DRM_LVDS_CODEC) += lvds-codec.o obj-$(CONFIG_DRM_MEGACHIPS_STDPXXXX_GE_B850V3_FW) += megachips-stdpxxxx-ge-b850v3-fw.o +obj-$(CONFIG_DRM_MICROCHIP_LVDS_SERIALIZER) += microchip-lvds.o obj-$(CONFIG_DRM_NXP_PTN3460) += nxp-ptn3460.o obj-$(CONFIG_DRM_PARADE_PS8622) += parade-ps8622.o obj-$(CONFIG_DRM_PARADE_PS8640) += parade-ps8640.o
drivers/gpu/drm/bridge/microchip-lvds.c new file +229 -0
229 lines not on this page · raw message
Signature · 1 line
2.25.1
Re: [PATCH v8 2/4] drm/bridge: add lvds controller support for sam9x7
Quoted 44 lines · Dharma Balasubiramani
Add a new LVDS controller driver for sam9x7 which does the following:
- Prepares and enables the LVDS Peripheral clock
- Defines its connector type asDRM_MODE_CONNECTOR_LVDSand adds itself to the global bridge list.
- Identifies its output endpoint as panel and adds it to the encoder display pipeline
- Enables the LVDS serializerSigned-off-by Manikandan Muralidharan <[email protected]>Signed-off-by Dharma Balasubiramani <[email protected]>---
Changelog
v7 -> v8
- Assign ret variable properly before checking it for err.
v6 -> v7
- Remove setting encoder type from bridge driver.
- Dropclk_disable()frompm_runtime_get_sync()error handling.
- Usedevm_clk_get()instead of prepared version.
- Hence useclk_prepare_enable()andclk_disable_unprepare().
- Usedevm_drm_of_get_bridge()instead ofdevm_drm_panel_bridge_add().
- Add error check fordevm_pm_runtime_enable().
- Usedev_err()instead ofDRM_DEV_ERROR()as it is deprecated.
- Add missing Acked-by tag.
v5 -> v6
- No Changes.
v4 -> v5
- Drop the unused variable 'format'.
- Use DRM wrapper fordev_err()to maintain uniformity.
- return-ENODEVinstead of-EINVALto maintain consistency with other DRM bridge drivers.
v3 -> v4
- No changes.
v2 ->v3
- Correct Typo error "serializer".
- Consolidateget()andprepare()functions and usedevm_clk_get_prepared().
- Remove unused variable 'ret' inprobe().
- Usedevm_pm_runtime_enable()and drop themchp_lvds_remove(). v1 -> v2
- Drop 'res' variable and combine two lines into one.
- Handle deferred probe properly, usedev_err_probe().
- Don't print anything on deferred probe. Dropped print.
- Remove theMODULE_ALIASand addMODULE_DEVICE_TABLE().
- symbol 'mchp_lvds_driver' was not declared. It should be static.
Quoted 7 lines
--- drivers/gpu/drm/bridge/Kconfig | 7 + drivers/gpu/drm/bridge/Makefile | 1 + drivers/gpu/drm/bridge/microchip-lvds.c | 229 ++++++++++++++++++++++++ 3 files changed, 237 insertions(+) create mode 100644 drivers/gpu/drm/bridge/microchip-lvds.c
Signature · 2 lines
With best wishes Dmitry
Dharma Balasubiramani
maintainerPATCH v8 3/4 MAINTAINERS: add SAM9X7 SoC's LVDS controller
In reply to Dharma BalasubiramaniAdd the newly added LVDS controller for the SAM9X7 SoC to the existing MAINTAINERS entry.
---
Changelog
v7 -> v8
v6 -> v7
- No changes.
v5 -> v6
- Correct the file name sam9x7-lvds.yaml -> sam9x75-lvds.yaml. v4 -> v5
v3 -> v4
- No changes.
v2 -> v3
- Move the entry before "MICROCHIP SAMA5D2-COMPATIBLE ADC DRIVER". v1 -> v2
- No Changes.
--- MAINTAINERS | 8 ++++++++ 1 file changed, 8 insertions(+)
MAINTAINERS +8 -0
@@ -14563,6 +14563,14 @@ S: Supported F: Documentation/devicetree/bindings/pwm/atmel,at91sam-pwm.yaml F: drivers/pwm/pwm-atmel.c +MICROCHIP SAM9x7-COMPATIBLE LVDS CONTROLLER +M: Manikandan Muralidharan <[email protected]> +M: Dharma Balasubiramani <[email protected]> +L: [email protected] +S: Supported +F: Documentation/devicetree/bindings/display/bridge/microchip,sam9x75-lvds.yaml +F: drivers/gpu/drm/bridge/microchip-lvds.c + MICROCHIP SAMA5D2-COMPATIBLE ADC DRIVER M: Eugen Hristev <[email protected]> L: [email protected]
Signature · 1 line
2.25.1
Dharma Balasubiramani
maintainerPATCH v8 4/4 ARM: configs: at91: Enable LVDS serializer support
In reply to Dharma BalasubiramaniEnable LVDS serializer support for display pipeline.
---
Changelog
v7 -> v8
v6 -> v7
v5 -> v6
v4 -> v5
v3 -> v4
v2 -> v3
- No Changes.
--- arch/arm/configs/at91_dt_defconfig | 1 + 1 file changed, 1 insertion(+)
arch/arm/configs/at91_dt_defconfig +1 -0
@@ -143,6 +143,7 @@ CONFIG_VIDEO_OV2640=m CONFIG_VIDEO_OV7740=m CONFIG_DRM=y CONFIG_DRM_ATMEL_HLCDC=y +CONFIG_DRM_MICROCHIP_LVDS_SERIALIZER=y CONFIG_DRM_PANEL_SIMPLE=y CONFIG_DRM_PANEL_EDP=y CONFIG_FB_ATMEL=y
Signature · 1 line
2.25.1
Re: [PATCH v8 4/4] ARM: configs: at91: Enable LVDS serializer support
Quoted 5 lines · Dharma Balasubiramani
Enable LVDS serializer support for display pipeline.
Signed-off-by Dharma Balasubiramani <[email protected]>Acked-by Nicolas Ferre <[email protected]>
Applied to at91-defconfig, thanks!
Re: (subset) [PATCH v8 0/4] LVDS Controller Support for SAM9X75 SoC
In reply to Dharma BalasubiramaniHi,
Quoted 11 lines · Dharma Balasubiramani
This patch series introduces LVDS controller support for the SAM9X75 SoC. The LVDS controller is designed to work with Microchip's sam9x7 series System-on-Chip (SoC) devices, providing Low Voltage Differential Signaling capabilities.
Patch series Changelog:
- Include configs: at91: Enable LVDS serializer
- include all necessary To/Cc entries.
The Individual Changelogs are available on the respective patches.[...]
Thanks, Applied to https://gitlab.freedesktop.org/drm/misc/kernel.git (drm-misc-next)
[1/4] dt-bindings: display: bridge: add sam9x75-lvds binding
https://gitlab.freedesktop.org/drm/misc/kernel/-/commit/c24177ca3b27e5a7ddaab8d330cedecd7eb9244a [2/4] drm/bridge: add lvds controller support for sam9x7 https://gitlab.freedesktop.org/drm/misc/kernel/-/commit/179b0769fc5fc193d7837bdcb6ddee118a0fa9b8 [3/4] MAINTAINERS: add SAM9X7 SoC's LVDS controller https://gitlab.freedesktop.org/drm/misc/kernel/-/commit/e95752752eaf06c860811ac5ddf9badf6c1b43ca
Signature · 1 line
Neil