Update the max31790 driver
Subsystems (2)
v2 cover Update the max31790 driver
Add the max31790 binding document and support maxim,pwmout-pin-as-tach-input vendor property for the max31790 device.
Changes in v2:
- Drop "driver" in the patch 1/3 commit title [Krzysztof] - Update filename of the maxim,max31790.yaml [Krzysztof] - Add the common fan schema to $ref [Krzysztof] - Update the node name to "fan-controller" in maxim,max31790.yaml [Krzysztof] - Update the vendor property name to "maxim,pwmout-pin-as-tach-input" [Rob]
Chanh Nguyen (3):
dt-bindings: hwmon: Add maxim max31790 bindings
hwmon: (max31790): Support config PWM output becomes TACH
dt-bindings: hwmon: max31790: Add maxim,pwmout-pin-as-tach-input
property
.../bindings/hwmon/maxim,max31790.yaml | 63 +++++++++++++++++++ drivers/hwmon/max31790.c | 31 +++++++++ 2 files changed, 94 insertions(+) create mode 100644 Documentation/devicetree/bindings/hwmon/maxim,max31790.yaml
Signature · 1 line
2.17.1
PATCH v2 1/3 dt-bindings: hwmon: Add maxim max31790 bindings
Add a device tree bindings for max31790 device.
---
Changes in v2:
- Update filename of the maxim,max31790.yaml [Krzysztof] - Add the common fan schema to $ref [Krzysztof] - Update the node name to "fan-controller" in maxim,max31790.yaml [Krzysztof] - Drop "driver" in commit title [Krzysztof] --- .../bindings/hwmon/maxim,max31790.yaml | 52 +++++++++++++++++++ 1 file changed, 52 insertions(+) create mode 100644 Documentation/devicetree/bindings/hwmon/maxim,max31790.yaml
Documentation/devicetree/bindings/hwmon/maxim,max31790.yaml new file +52 -0
@@ -0,0 +1,52 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/hwmon/maxim,max31790.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: The Maxim MAX31790 Fan Controller + +maintainers: + - Guenter Roeck <[email protected]> + +description: > + The MAX31790 controls the speeds of up to six fans using six + independent PWM outputs. The desired fan speeds (or PWM duty cycles) + are written through the I2C interface. + + Datasheets: + https://datasheets.maximintegrated.com/en/ds/MAX31790.pdf + +properties: + compatible: + const: maxim,max31790 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + resets: + maxItems: 1 + +required: + - compatible + - reg + +allOf: + - $ref: fan-common.yaml# + +unevaluatedProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + fan-controller@20 { + compatible = "maxim,max31790"; + reg = <0x20>; + }; + };
Signature · 1 line
2.17.1
Re: [PATCH v2 1/3] dt-bindings: hwmon: Add maxim max31790 bindings
Quoted 2 lines · Chanh Nguyen
Add a device tree bindings for max31790 device.
Nothing improved in commit msg, where is the rationale of split of bindings?
A nit, subject: drop second/last, redundant "bindings". The "dt-bindings" prefix is already stating that these are bindings. See also:
https://elixir.bootlin.com/linux/v6.7-rc8/source/Documentation/devicetree/bindings/submitting-patches.rst#L18
Quoted 58 lines
Signed-off-by Chanh Nguyen <[email protected]>---
Changes in v2:- Update filename of the maxim,max31790.yaml [Krzysztof] - Add the common fan schema to $ref [Krzysztof] - Update the node name to "fan-controller" in maxim,max31790.yaml [Krzysztof] - Drop "driver" in commit title [Krzysztof] --- .../bindings/hwmon/maxim,max31790.yaml | 52 +++++++++++++++++++ 1 file changed, 52 insertions(+) create mode 100644 Documentation/devicetree/bindings/hwmon/maxim,max31790.yamlDocumentation/devicetree/bindings/hwmon/maxim,max31790.yaml new file +40
-0@@ -0,0 +1,52 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/hwmon/maxim,max31790.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: The Maxim MAX31790 Fan Controller + +maintainers: + - Guenter Roeck <[email protected]> + +description: > + The MAX31790 controls the speeds of up to six fans using six + independent PWM outputs. The desired fan speeds (or PWM duty cycles) + are written through the I2C interface. + + Datasheets: + https://datasheets.maximintegrated.com/en/ds/MAX31790.pdf + +properties: + compatible: + const: maxim,max31790 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + resets: + maxItems: 1 + +required: + - compatible + - reg + +allOf: + - $ref: fan-common.yaml# + +unevaluatedProperties: false
Documentation/devicetree/bindings/hwmon/maxim,max31790.yaml line 50
Quoted 10 lines
Documentation/devicetree/bindings/hwmon/maxim,max31790.yaml new file +10
-0+ +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + fan-controller@20 { + compatible = "maxim,max31790"; + reg = <0x20>;
Make the example complete - add all properties, like clocks, resets and any others which are applicable.
Best regards,
Krzysztof
Re: [PATCH v2 1/3] dt-bindings: hwmon: Add maxim max31790 bindings
Quoted 6 lines · Krzysztof Kozlowski
Quoted 2 lines · Chanh Nguyen
Add a device tree bindings for max31790 device.
Nothing improved in commit msg, where is the rationale of split of bindings?
Yes Krzysztof, I will use "tach-ch" property from the fan-common.yaml to solve my case. So I will not need a split of bindings.
Finally, my patch series will only be two patches. They are "dt-bindings: hwmon: Add maxim max31790" and "hwmon: (max31790): Support config PWM output becomes TACH".
I'm going to update that in the patch v3 series.
Quoted 5 lines
A nit, subject: drop second/last, redundant "bindings". The "dt-bindings" prefix is already stating that these are bindings. See also:
https://elixir.bootlin.com/linux/v6.7-rc8/source/Documentation/devicetree/bindings/submitting-patches.rst#L18
Thank Krzysztof, I'll drop "bindings" in commit msg.
Quoted 63 lines
Quoted 63 lines
Signed-off-by Chanh Nguyen <[email protected]>---
Changes in v2:- Update filename of the maxim,max31790.yaml [Krzysztof] - Add the common fan schema to $ref [Krzysztof] - Update the node name to "fan-controller" in maxim,max31790.yaml [Krzysztof] - Drop "driver" in commit title [Krzysztof] --- .../bindings/hwmon/maxim,max31790.yaml | 52 +++++++++++++++++++ 1 file changed, 52 insertions(+)create mode 100644
Documentation/devicetree/bindings/hwmon/maxim,max31790.yamlDocumentation/devicetree/bindings/hwmon/maxim,max31790.yaml new file +45
-0@@ -0,0 +1,52 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/hwmon/maxim,max31790.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: The Maxim MAX31790 Fan Controller + +maintainers: + - Guenter Roeck <[email protected]> + +description: > + The MAX31790 controls the speeds of up to six fans using six + independent PWM outputs. The desired fan speeds (or PWM duty cycles) + are written through the I2C interface. + + Datasheets: + https://datasheets.maximintegrated.com/en/ds/MAX31790.pdf + +properties: + compatible: + const: maxim,max31790 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + resets: + maxItems: 1 + +required: + - compatible + - reg + +allOf: + - $ref: fan-common.yaml# + +unevaluatedProperties: false + +examples: + - | + i2c { + #address-cells = <1>;
Quoted 9 lines
Documentation/devicetree/bindings/hwmon/maxim,max31790.yaml line 50
Quoted 5 lines
Documentation/devicetree/bindings/hwmon/maxim,max31790.yaml new file +5
-0+ #size-cells = <0>; + + fan-controller@20 { + compatible = "maxim,max31790"; + reg = <0x20>;Make the example complete - add all properties, like clocks, resets and any others which are applicable.
Ok Krzysztof, I'll update that in the patch v3
Quoted 3 lines
Best regards,
Krzysztof
PATCH v2 2/3 hwmon: (max31790): Support config PWM output becomes TACH
In reply to Chanh NguyenPWMOUT pins on MAX31790 can be configured as a tachometer input pin by setting bit[0] in the Configuration Register. When the bit[0] of a channel is set, the PWMOUT pin becomes the tach input pin for the channel plus six.
This commit allows the kernel to set those pins when necessary if the maxim,pwmout-pin-as-tach-input DT property exists.
---
Changes in v2:
- Update the vendor property name to "maxim,pwmout-pin-as-tach-input" [Rob]
--- drivers/hwmon/max31790.c | 31 +++++++++++++++++++++++++++++++ 1 file changed, 31 insertions(+)
drivers/hwmon/max31790.c +31 -0
@@ -12,6 +12,7 @@#include <linux/init.h> #include <linux/jiffies.h> #include <linux/module.h> +#include <linux/property.h> #include <linux/slab.h> /* MAX31790 registers */
@@ -506,9 +507,12 @@ static int max31790_probe(struct i2c_client *client) {struct i2c_adapter *adapter = client->adapter;struct device *dev = &client->dev; +u8 pwmout_to_tach[NR_CHANNEL ];struct max31790_data *data;struct device *hwmon_dev;int err; +u8 tmp; +int i;if (!i2c_check_functionality (adapter,I2C_FUNC_SMBUS_BYTE_DATA |I2C_FUNC_SMBUS_WORD_DATA ))
@@ -528,6 +532,33 @@ static int max31790_probe(struct i2c_client *client)if (err)return err; +if (device_property_present (dev,"maxim,pwmout-pin-as-tach-input" )) { + err =device_property_read_u8_array (dev,"maxim,pwmout-pin-as-tach-input" , + pwmout_to_tach,NR_CHANNEL ); +if (err) { +/* The maxim,pwmout-pin-as-tach-input is an array of six values */ +dev_warn (dev,"The maxim,pwmout-pin-as-tach-input property exist but malform" ); + }else { +for (i =0 ; i <NR_CHANNEL ; i++) { + tmp = data->fan_config[i]; +if (pwmout_to_tach[i]) + data->fan_config[i] |=MAX31790_FAN_CFG_TACH_INPUT ; +else + data->fan_config[i] &= ~(MAX31790_FAN_CFG_TACH_INPUT ); + +if (tmp != data->fan_config[i]) { + err =i2c_smbus_write_byte_data (client, +MAX31790_REG_FAN_CONFIG (i), + data->fan_config[i]); +if (err <0 ) +dev_warn (dev, +"Fail to apply fan configuration at channel %d" , + i); + } + } + } + } + hwmon_dev = devm_hwmon_device_register_with_info(dev, client->name, data, &max31790_chip_info,
Signature · 1 line
2.17.1
Re: [PATCH v2 2/3] hwmon: (max31790): Support config PWM output becomes TACH
Le 14/04/2024 à 06:22, Chanh Nguyen a écrit :
Quoted 11 lines
PWMOUT pins on MAX31790 can be configured as a tachometer input pin by setting bit[0] in the Configuration Register. When the bit[0] of a channel is set, the PWMOUT pin becomes the tach input pin for the channel plus six.
This commit allows the kernel to set those pins when necessary if the maxim,pwmout-pin-as-tach-input DT property exists.
Signed-off-by Chanh Nguyen <[email protected]>---
Changes in v2:
- Update the vendor property name to "maxim,pwmout-pin-as-tach-input" [Rob]
...
drivers/hwmon/max31790.c static int max31790_probe(struct i2c_client *client) · line 540
Quoted 10 lines
drivers/hwmon/max31790.c +6
-0@@ -528,6 +532,33 @@ static int max31790_probe(struct i2c_client *client)if (err)return err; +if (device_property_present (dev,"maxim,pwmout-pin-as-tach-input" )) { + err =device_property_read_u8_array (dev,"maxim,pwmout-pin-as-tach-input" , + pwmout_to_tach,NR_CHANNEL ); +if (err) { +/* The maxim,pwmout-pin-as-tach-input is an array of six values */ +dev_warn (dev,"The maxim,pwmout-pin-as-tach-input property exist but malform" );
Nit: exists
Nit: malformed or "is malformed"
CJ
Re: [PATCH v2 2/3] hwmon: (max31790): Support config PWM output becomes TACH
Quoted 8 lines · Christophe JAILLET
Le 14/04/2024 à 06:22, Chanh Nguyen a écrit :
Quoted 7 lines
PWMOUT pins on MAX31790 can be configured as a tachometer input pin by setting bit[0] in the Configuration Register. When the bit[0] of a channel is set, the PWMOUT pin becomes the tach input pin for the channel plus six.
This commit allows the kernel to set those pins when necessary if the maxim,pwmout-pin-as-tach-input DT property exists.
Quoted 6 lines
Quoted 4 lines
Signed-off-by Chanh Nguyen <[email protected]>---
Changes in v2:
- Update the vendor property name to "maxim,pwmout-pin-as-tach-input" [Rob]...
Hi CJ, what does it mean?
Quoted 18 lines
Quoted 11 lines
(quoted diff) +5
-0@@ -528,6 +532,33 @@ static int max31790_probe(struct i2c_client *client) if (err) return err; + if (device_property_present(dev, "maxim,pwmout-pin-as-tach-input")) { + err = device_property_read_u8_array(dev, "maxim,pwmout-pin-as-tach-input", + pwmout_to_tach, NR_CHANNEL); + if (err) { + /* The maxim,pwmout-pin-as-tach-input is an array of sixQuoted 3 lines
values */
+dev_warn(dev, "The maxim,pwmout-pin-as-tach-input property exist but malform");Nit: exists
Nit: malformed or "is malformed"
Thank CJ,
I'll update that in the patch v3
Quoted 1 line
CJ
Re: [PATCH v2 2/3] hwmon: (max31790): Support config PWM output becomes TACH
Le 16/04/2024 à 07:27, Chanh Nguyen a écrit :
Quoted 11 lines · Christophe JAILLET
Quoted 8 lines
Le 14/04/2024 à 06:22, Chanh Nguyen a écrit :
Quoted 7 lines
PWMOUT pins on MAX31790 can be configured as a tachometer input pin by setting bit[0] in the Configuration Register. When the bit[0] of a channel is set, the PWMOUT pin becomes the tach input pin for the channel plus six.
This commit allows the kernel to set those pins when necessary if the maxim,pwmout-pin-as-tach-input DT property exists.
Quoted 8 lines
Quoted 6 lines
Quoted 4 lines
Signed-off-by Chanh Nguyen <[email protected]>---
Changes in v2:
- Update the vendor property name to "maxim,pwmout-pin-as-tach-input" [Rob]...
Hi CJ, what does it mean?
Hi,
just a shortcut of my name : Christophe Jaillet.
CJ
Quoted 27 lines
Quoted 10 lines
Quoted 10 lines
(quoted diff) +3
-0@@ -528,6 +532,33 @@ static int max31790_probe(struct i2c_client *client) if (err) return err; + if (device_property_present(dev, "maxim,pwmout-pin-as-tach-input")) { + err = device_property_read_u8_array(dev, "maxim,pwmout-pin-as-tach-input", + pwmout_to_tach, NR_CHANNEL);Quoted 9 lines
Quoted 5 lines
(quoted diff) +2
-0+ if (err) { + /* The maxim,pwmout-pin-as-tach-input is an array of sixvalues */
+dev_warn(dev, "The maxim,pwmout-pin-as-tach-input property exist but malform");Nit: exists
Nit: malformed or "is malformed"Thank CJ,
I'll update that in the patch v3
Quoted 1 line
CJ
Re: [PATCH v2 2/3] hwmon: (max31790): Support config PWM output becomes TACH
Quoted 17 lines · Christophe JAILLET
Le 16/04/2024 à 07:27, Chanh Nguyen a écrit :
Quoted 16 lines · Christophe JAILLET
Quoted 13 lines
Le 14/04/2024 à 06:22, Chanh Nguyen a écrit :
Quoted 11 lines
PWMOUT pins on MAX31790 can be configured as a tachometer input pin by setting bit[0] in the Configuration Register. When the bit[0] of a channel is set, the PWMOUT pin becomes the tach input pin for the channel plus six.
This commit allows the kernel to set those pins when necessary if the maxim,pwmout-pin-as-tach-input DT property exists.
Signed-off-by Chanh Nguyen <[email protected]>---
Changes in v2:
- Update the vendor property name to "maxim,pwmout-pin-as-tach-input" [Rob]
Quoted 7 lines
Quoted 3 lines
Quoted 1 line
...
Hi CJ, what does it mean?
Hi,
just a shortcut of my name : Christophe Jaillet.
Thank CJ! It's a pleasure to see your comments. I'm happy to meet your review in the next patches.
Best Regards,
Chanh Ng
Quoted 30 lines
CJ
Quoted 27 lines
Quoted 10 lines
Quoted 10 lines
(quoted diff) +3
-0@@ -528,6 +532,33 @@ static int max31790_probe(struct i2c_client *client) if (err) return err; + if (device_property_present(dev, "maxim,pwmout-pin-as-tach-input")) { + err = device_property_read_u8_array(dev, "maxim,pwmout-pin-as-tach-input", + pwmout_to_tach, NR_CHANNEL);Quoted 9 lines
Quoted 5 lines
(quoted diff) +2
-0+ if (err) { + /* The maxim,pwmout-pin-as-tach-input is an array ofsix values */
+dev_warn(dev, "The maxim,pwmout-pin-as-tach-input property exist but malform");Nit: exists
Nit: malformed or "is malformed"Thank CJ,
I'll update that in the patch v3
Quoted 1 line
CJ
PATCH v2 3/3 dt-bindings: hwmon: max31790: Add maxim,pwmout-pin-as-tach-input property
In reply to Chanh NguyenThe max31790 supports six pins, which are dedicated PWM outputs. Any of the six PWM outputs can also be configured to serve as tachometer inputs, allowing for up to 12 tachometer fans to be monitored.
Add a new vendor-specific property, 'maxim,pwmout-pin-as-tach-input', to allow PWMOUT to become a TACH input.
An array of six integers responds to six PWM channels for configuring the PWM to TACH mode. When set to 0, the associated PWMOUT produces a PWM waveform for control of fan speed. When set to 1, PWMOUT becomes a TACH input.
---
Changes in v2:
- Update the vendor property name to "maxim,pwmout-pin-as-tach-input" [Rob]
- Update commit message [Krzysztof]
--- .../devicetree/bindings/hwmon/maxim,max31790.yaml | 11 +++++++++++ 1 file changed, 11 insertions(+)
Documentation/devicetree/bindings/hwmon/maxim,max31790.yaml +11 -0
@@ -30,6 +30,16 @@ properties: resets: maxItems: 1 + maxim,pwmout-pin-as-tach-input: + description: | + An array of six integers responds to six PWM channels for + configuring the pwm to tach mode. + When set to 0, the associated PWMOUT produces a PWM waveform for + control of fan speed. When set to 1, PWMOUT becomes a TACH input + $ref: /schemas/types.yaml#/definitions/uint8-array + maxItems: 6 + minItems: 6 + required: - compatible - reg
@@ -48,5 +58,6 @@ examples: fan-controller@20 { compatible = "maxim,max31790"; reg = <0x20>; + maxim,pwmout-pin-as-tach-input = /bits/ 8 <0 0 0 0 1 1>; }; };
Signature · 1 line
2.17.1
Re: [PATCH v2 3/3] dt-bindings: hwmon: max31790: Add maxim,pwmout-pin-as-tach-input property
Quoted 12 lines · Chanh Nguyen
The max31790 supports six pins, which are dedicated PWM outputs. Any of the six PWM outputs can also be configured to serve as tachometer inputs, allowing for up to 12 tachometer fans to be monitored.
Add a new vendor-specific property, 'maxim,pwmout-pin-as-tach-input', to allow PWMOUT to become a TACH input.
An array of six integers responds to six PWM channels for configuring the PWM to TACH mode. When set to 0, the associated PWMOUT produces a PWM waveform for control of fan speed. When set to 1, PWMOUT becomes a TACH input.
Quoted 5 lines
Signed-off-by Chanh Nguyen <[email protected]>---
Changes in v2:
- Update the vendor property name to "maxim,pwmout-pin-as-tach-input" [Rob]
- Update commit message [Krzysztof]
Please put binding before its user.
Quoted 11 lines
--- .../devicetree/bindings/hwmon/maxim,max31790.yaml | 11 +++++++++++ 1 file changed, 11 insertions(+)Documentation/devicetree/bindings/hwmon/maxim,max31790.yaml +0
-0@@ -30,6 +30,16 @@ properties: resets: maxItems: 1
Documentation/devicetree/bindings/hwmon/maxim,max31790.yaml properties: · line 41
Quoted 10 lines
Documentation/devicetree/bindings/hwmon/maxim,max31790.yaml +9
-0+ maxim,pwmout-pin-as-tach-input: + description: | + An array of six integers responds to six PWM channels for + configuring the pwm to tach mode. + When set to 0, the associated PWMOUT produces a PWM waveform for + control of fan speed. When set to 1, PWMOUT becomes a TACH input + $ref: /schemas/types.yaml#/definitions/uint8-array + maxItems: 6 + minItems: 6
tach-ch solves your case. You define which inputs should be used for tach.
Best regards,
Krzysztof
Re: [PATCH v2 3/3] dt-bindings: hwmon: max31790: Add maxim,pwmout-pin-as-tach-input property
Quoted 13 lines · Krzysztof Kozlowski
Quoted 12 lines · Chanh Nguyen
The max31790 supports six pins, which are dedicated PWM outputs. Any of the six PWM outputs can also be configured to serve as tachometer inputs, allowing for up to 12 tachometer fans to be monitored.
Add a new vendor-specific property, 'maxim,pwmout-pin-as-tach-input', to allow PWMOUT to become a TACH input.
An array of six integers responds to six PWM channels for configuring the PWM to TACH mode. When set to 0, the associated PWMOUT produces a PWM waveform for control of fan speed. When set to 1, PWMOUT becomes a TACH input.
Quoted 8 lines
Quoted 5 lines
Signed-off-by Chanh Nguyen <[email protected]>---
Changes in v2:
- Update the vendor property name to "maxim,pwmout-pin-as-tach-input" [Rob]
- Update commit message [Krzysztof]Please put binding before its user.
Hi Krzysztof, I'll drop this [Path 3/3] in the patch series v3.
My patch series will only be two patches. They are "dt-bindings: hwmon: Add maxim max31790" and "hwmon: (max31790): Support config PWM output becomes TACH"
Quoted 12 lines
Quoted 12 lines
--- .../devicetree/bindings/hwmon/maxim,max31790.yaml | 11 +++++++++++ 1 file changed, 11 insertions(+)Documentation/devicetree/bindings/hwmon/maxim,max31790.yaml +0
-0@@ -30,6 +30,16 @@ properties: resets: maxItems: 1
Quoted 12 lines
Documentation/devicetree/bindings/hwmon/maxim,max31790.yaml properties: · line 41
Quoted 9 lines
Documentation/devicetree/bindings/hwmon/maxim,max31790.yaml +9
-0+ maxim,pwmout-pin-as-tach-input: + description: | + An array of six integers responds to six PWM channels for + configuring the pwm to tach mode. + When set to 0, the associated PWMOUT produces a PWM waveform for + control of fan speed. When set to 1, PWMOUT becomes a TACH input + $ref: /schemas/types.yaml#/definitions/uint8-array + maxItems: 6 + minItems: 6tach-ch solves your case. You define which inputs should be used for tach.
Agree Krzysztof. I'll use the tach-ch property from the fan-common.yaml to solve my case. So I will not need to define a new vendor property as "maxim,pwmout-pin-as-tach-input". I'll drop this [Path 3/3] in the patch series v3.
Quoted 3 lines
Best regards,
Krzysztof
Re: [PATCH v2 3/3] dt-bindings: hwmon: max31790: Add maxim,pwmout-pin-as-tach-input property
Quoted 53 lines · Chanh Nguyen
Quoted 13 lines · Krzysztof Kozlowski
Quoted 12 lines · Chanh Nguyen
The max31790 supports six pins, which are dedicated PWM outputs. Any of the six PWM outputs can also be configured to serve as tachometer inputs, allowing for up to 12 tachometer fans to be monitored.
Add a new vendor-specific property, 'maxim,pwmout-pin-as-tach-input', to allow PWMOUT to become a TACH input.
An array of six integers responds to six PWM channels for configuring the PWM to TACH mode. When set to 0, the associated PWMOUT produces a PWM waveform for control of fan speed. When set to 1, PWMOUT becomes a TACH input.
Quoted 8 lines
Quoted 5 lines
Signed-off-by Chanh Nguyen <[email protected]>---
Changes in v2:
- Update the vendor property name to "maxim,pwmout-pin-as-tach-input" [Rob]
- Update commit message [Krzysztof]Please put binding before its user.
Hi Krzysztof, I'll drop this [Path 3/3] in the patch series v3.
My patch series will only be two patches. They are "dt-bindings: hwmon: Add maxim max31790" and "hwmon: (max31790): Support config PWM output becomes TACH"
Quoted 14 lines
Quoted 14 lines
---
.../devicetree/bindings/hwmon/maxim,max31790.yaml | 11 +++++++++++1 file changed, 11 insertions(+)Documentation/devicetree/bindings/hwmon/maxim,max31790.yaml +0
-0@@ -30,6 +30,16 @@ properties:resets:
maxItems: 1
+ maxim,pwmout-pin-as-tach-input:
+ description: |
+ An array of six integers responds to six PWM channels forQuoted 9 lines
Quoted 6 lines
+ configuring the pwm to tach mode.
+ When set to 0, the associated PWMOUT produces a PWM waveform for + control of fan speed. When set to 1, PWMOUT becomes a TACH input + $ref: /schemas/types.yaml#/definitions/uint8-array
+ maxItems: 6
+ minItems: 6tach-ch solves your case. You define which inputs should be used for tach.
Quoted 6 lines
Agree Krzysztof. I'll use the tach-ch property from the
fan-common.yamlto solve my case. So I will not need to define a new vendor property as "maxim,pwmout-pin-as-tach-input". I'll drop this [Path 3/3] in the patch series v3.Quoted 3 lines
Best regards,
Krzysztof
Hi Krzysztof,
I checked in the Documentation/devicetree/bindings/hwmon/fan-common.yaml. I found the tach-ch property, but it seems define the tach channel used for fan.
tach-ch:
description:
The tach channel used for the fan.
$ref: /schemas/types.yaml#/definitions/uint8-array
In my purpose, I would like to configure the pwm output pins to become tachometer input pins by setting bit[0] in the Configuration Register.
I think a vendor property is suitable for this purpose. It is only available on specific MAX31790 fan controllers and not on other fan controller devices. So I think we can't use the "tach-ch" in fan-common.yaml.
I discussed it in the thread
https://lore.kernel.org/lkml/[email protected]/ , but I have not yet received Rob's response.
Please share your comment with me. I hope that will help us make a final decision.
Thank Krzysztof very much!
Re: [PATCH v2 3/3] dt-bindings: hwmon: max31790: Add maxim,pwmout-pin-as-tach-input property
Quoted 88 lines · Chanh Nguyen
Quoted 62 lines · Chanh Nguyen
Quoted 23 lines · Krzysztof Kozlowski
Quoted 13 lines · Chanh Nguyen
The max31790 supports six pins, which are dedicated PWM outputs. Any of the
six PWM outputs can also be configured to serve as tachometer inputs, allowing for up to 12 tachometer fans to be monitored.Add a new vendor-specific property, 'maxim,pwmout-pin-as-tach-input', to allow PWMOUT to become a TACH input.
An array of six integers responds to six PWM channels for configuring the PWM to TACH mode. When set to 0, the associated PWMOUT produces a PWM waveform for control of fan speed. When set to 1, PWMOUT becomes a TACH input.
Quoted 8 lines
Signed-off-by Chanh Nguyen <[email protected]>---
Changes in v2:
- Update the vendor property name to
"maxim,pwmout-pin-as-tach-input" [Rob]
- Update commit
message
[Krzysztof]Quoted 2 lines
Please put binding before its user.
Hi Krzysztof, I'll drop this [Path 3/3] in the patch series v3.
My patch series will only be two patches. They are "dt-bindings: hwmon:
Add maxim max31790" and "hwmon: (max31790): Support config PWM output becomes TACH"Quoted 17 lines
Quoted 17 lines
---
.../devicetree/bindings/hwmon/maxim,max31790.yaml | 11 +++++++++++1 file changed, 11 insertions(+)diff --git
a/Documentation/devicetree/bindings/hwmon/maxim,max31790.yamlb/Documentation/devicetree/bindings/hwmon/maxim,max31790.yamlindexa561e5a3e9e4..2d4f50bc7c41100644Documentation/devicetree/bindings/hwmon/maxim,max31790.yaml +0
-0@@ -30,6 +30,16 @@ properties:resets:
maxItems: 1
+ maxim,pwmout-pin-as-tach-input:
+ description: |
+ An array of six integers responds to six PWM channels for + configuring the pwm to tach mode.Quoted 9 lines
Quoted 5 lines
+ When set to 0, the associated PWMOUT produces a PWM waveform for + control of fan speed. When set to 1, PWMOUT becomes a TACH input + $ref: /schemas/types.yaml#/definitions/uint8-array
+ maxItems: 6
+ minItems: 6tach-ch solves your case. You define which inputs should be used for tach.
Quoted 9 lines
Agree Krzysztof. I'll use the tach-ch property from the
fan-common.yamlto solve my case. So I will not need to define a new vendor property as "maxim,pwmout-pin-as-tach-input". I'll drop this [Path 3/3] in the patch series v3.Quoted 3 lines
Best regards,
KrzysztofHi Krzysztof,
I checked in the
Documentation/devicetree/bindings/hwmon/fan-common.yaml. I found the tach-ch property, but it seems define the tach channel used for fan.tach-ch:
description:
The tach channel used for the fan.
$ref: /schemas/types.yaml#/definitions/uint8-array
Quoted 7 lines
In my purpose, I would like to configure the pwm output pins to become tachometer input pins by setting bit[0] in the Configuration Register.
I think a vendor property is suitable for this purpose. It is only available on specific MAX31790 fan controllers and not on other fan controller devices. So I think we can't use the "tach-ch" in
fan-common.yaml.
Can you explain why you think that only MAX31790 fan controllers are capable of an arbitrary mapping of PWM outputs to TACH inputs?
Re: [PATCH v2 3/3] dt-bindings: hwmon: max31790: Add maxim,pwmout-pin-as-tach-input property
Quoted 2 lines · Conor Dooley
[EXTERNAL EMAIL NOTICE: This email originated from an external sender. Please be mindful of safe email handling and proprietary information protection practices.]
Sorry Conor, there may be confusion here. I mean the mapping of the PWM output to the TACH input, which is on the MAX31790, and it is not sure a common feature on all fan controllers.
I would like to open a discussion about whether we should use the tach-ch property on the fan-common.yaml
I'm looking forward to hearing comments from everyone. For me, both tach-ch and vendor property are good.
Thank you, Conor!
Guenter Roeck
maintainerRe: [PATCH v2 3/3] dt-bindings: hwmon: max31790: Add maxim,pwmout-pin-as-tach-input property
Quoted 6 lines · Chanh Nguyen
Quoted 2 lines · Conor Dooley
[EXTERNAL EMAIL NOTICE: This email originated from an external sender. Please be mindful of safe email handling and proprietary information protection practices.]
The quote doesn't make much sense.
Quoted 2 lines
Sorry Conor, there may be confusion here. I mean the mapping of the PWM output to the TACH input, which is on the MAX31790, and it is not sure a common feature on all fan controllers.
I think the term "mapping" is a bit confusing here.
tach-ch, as I understand it, is supposed to associate a tachometer input with a pwm output, meaning the fan speed measured with the tachometer input is expected to change if the pwm output changes.
On MAX31790, it is possible to configure a pwm output pin as tachometer input pin. That is something completely different. Also, the association is fixed. If the first pwm channel is used as tachometer channel, it would show up as 7th tachometer channel. If the 6th pwm channel is configured to be used as tachometer input, it would show up as 12th tachometer channel.
Overall, the total number of channels on MAX31790 is always 12. 6 of them are always tachometer inputs, the others can be configured to either be a pwm output or a tachometer input.
pwm outputs on MAX31790 are always tied to the matching tachometer inputs (pwm1 <--> tach1 etc) and can not be reconfigured, meaning tach-ch for channel X would always be X.
Quoted 4 lines
I would like to open a discussion about whether we should use the tach-ch property on the
fan-common.yamlI'm looking forward to hearing comments from everyone. For me, both tach-ch and vendor property are good.
I am not even sure how to define tach-ch to mean "use the pwm output pin associated with this tachometer input channel not as pwm output but as tachometer input". That would be a boolean, not a number.
Guenter
Re: [PATCH v2 3/3] dt-bindings: hwmon: max31790: Add maxim,pwmout-pin-as-tach-input property
Quoted 33 lines · Guenter Roeck
Quoted 6 lines · Chanh Nguyen
Quoted 2 lines · Conor Dooley
[EXTERNAL EMAIL NOTICE: This email originated from an external sender. Please be mindful of safe email handling and proprietary information protection practices.]
The quote doesn't make much sense.
Quoted 2 lines
Sorry Conor, there may be confusion here. I mean the mapping of the PWM output to the TACH input, which is on the MAX31790, and it is not sure a common feature on all fan controllers.
I think the term "mapping" is a bit confusing here.
tach-ch, as I understand it, is supposed to associate a tachometer input with a pwm output, meaning the fan speed measured with the tachometer input is expected to change if the pwm output changes.
On MAX31790, it is possible to configure a pwm output pin as tachometer input pin. That is something completely different. Also, the association is fixed. If the first pwm channel is used as tachometer channel, it would show up as 7th tachometer channel. If the 6th pwm channel is configured to be used as tachometer input, it would show up as 12th tachometer channel.
Overall, the total number of channels on MAX31790 is always 12. 6 of them are always tachometer inputs, the others can be configured to either be a pwm output or a tachometer input.
pwm outputs on MAX31790 are always tied to the matching tachometer inputs (pwm1 <--> tach1 etc) and can not be reconfigured, meaning tach-ch for channel X would always be X.
Quoted 8 lines
Quoted 4 lines
I would like to open a discussion about whether we should use the tach-ch property on the
fan-common.yamlI'm looking forward to hearing comments from everyone. For me, both tach-ch and vendor property are good.
I am not even sure how to define tach-ch to mean "use the pwm output pin associated with this tachometer input channel not as pwm output but as tachometer input". That would be a boolean, not a number.
Thanks for explanation. So this is basically pin controller function choice - kind of output or input, although not in terms of GPIO.
Shouldn't we have then fan children which will be consumers of PWMs? Having a consumer makes pin PWM output. Then tach-ch says which pins are tachometer for given fan? Just like aspeed,g6-pwm-tach.yaml has?
Best regards,
Krzysztof
Re: [PATCH v2 3/3] dt-bindings: hwmon: max31790: Add maxim,pwmout-pin-as-tach-input property
Quoted 10 lines · Krzysztof Kozlowski
Quoted 9 lines · Guenter Roeck
Quoted 6 lines · Chanh Nguyen
Quoted 2 lines · Conor Dooley
[EXTERNAL EMAIL NOTICE: This email originated from an external sender. Please be mindful of safe email handling and proprietary information protection practices.]
The quote doesn't make much sense.
The reply is to me questioning part of their earlier reply:
> I think a vendor property is suitable for this purpose. It is only available > on specific MAX31790 fan controllers and not on other fan controller > devices. So I think we can't use the "tach-ch" in fan-common.yaml.
Can you explain why you think that only MAX31790 fan controllers are capable of an arbitrary mapping of PWM outputs to TACH inputs?
Quoted 16 lines
Quoted 16 lines
Quoted 3 lines
Sorry Conor, there may be confusion here. I mean the mapping of the PWM output to the TACH input, which is on the MAX31790, and it is not sure a common feature on all fan controllers.
I think the term "mapping" is a bit confusing here.
tach-ch, as I understand it, is supposed to associate a tachometer input with a pwm output, meaning the fan speed measured with the tachometer input is expected to change if the pwm output changes.
On MAX31790, it is possible to configure a pwm output pin as tachometer input pin. That is something completely different. Also, the association is fixed. If the first pwm channel is used as tachometer channel, it would show up as 7th tachometer channel. If the 6th pwm channel is configured to be used as tachometer input, it would show up as 12th tachometer channel.
Quoted 8 lines
Quoted 8 lines
Overall, the total number of channels on MAX31790 is always 12. 6 of them are always tachometer inputs, the others can be configured to either be a pwm output or a tachometer input.
pwm outputs on MAX31790 are always tied to the matching tachometer inputs (pwm1 <--> tach1 etc) and can not be reconfigured, meaning tach-ch for channel X would always be X.
Are they? Granted, I probably didn't read this as well as you did, but figure 3, 4 5 & 6 seem to show mappings that are not 1:1, with PWMOUT1 controlling several fans, each of which report back via a different tach channel. I think the fan controller binding accounts for this though:
the child nodes would reference the same PWM provider but have different tach-ch values.
Quoted 10 lines
Quoted 9 lines
Quoted 5 lines
I would like to open a discussion about whether we should use the tach-ch property on the
fan-common.yamlI'm looking forward to hearing comments from everyone. For me, both tach-ch and vendor property are good.
I am not even sure how to define tach-ch to mean "use the pwm output pin associated with this tachometer input channel not as pwm output but as tachometer input". That would be a boolean, not a number.
Quoted 5 lines
Thanks for explanation. So this is basically pin controller function choice - kind of output or input, although not in terms of GPIO.
Shouldn't we have then fan children which will be consumers of PWMs?
In this case, the max31790 has the PWM hardware, so it would be the provider...
Quoted 2 lines
Having a consumer makes pin PWM output. Then tach-ch says which pins are tachometer for given fan? Just like aspeed,g6-pwm-tach.yaml has?
...and it seems to me like there should be several fan child nodes as in the aspeed binding you mention here that are the consumers. The binding as written seems to only support a single fan.
Re: [PATCH v2 3/3] dt-bindings: hwmon: max31790: Add maxim,pwmout-pin-as-tach-input property
In reply to Guenter RoeckQuoted 25 lines · Guenter Roeck
Quoted 6 lines · Chanh Nguyen
Quoted 2 lines · Conor Dooley
[EXTERNAL EMAIL NOTICE: This email originated from an external sender. Please be mindful of safe email handling and proprietary information protection practices.]
The quote doesn't make much sense.
Quoted 2 lines
Sorry Conor, there may be confusion here. I mean the mapping of the PWM output to the TACH input, which is on the MAX31790, and it is not sure a common feature on all fan controllers.
I think the term "mapping" is a bit confusing here.
tach-ch, as I understand it, is supposed to associate a tachometer input with a pwm output, meaning the fan speed measured with the tachometer input is expected to change if the pwm output changes.
On MAX31790, it is possible to configure a pwm output pin as tachometer input pin. That is something completely different. Also, the association is fixed. If the first pwm channel is used as tachometer channel, it would show up as 7th tachometer channel. If the 6th pwm channel is configured to be used as tachometer input, it would show up as 12th tachometer channel.
Quoted 3 lines
Overall, the total number of channels on MAX31790 is always 12. 6 of them are always tachometer inputs, the others can be configured to either be a pwm output or a tachometer input.
Thank you, Guenter, for your explanation. That is also my understanding of the MAX31790 feature.
So, I think we should introduce a vendor property to configure the pwm output pins to become tachometer input pins. We shouldn't use the tach-ch property. Because they are completely different, I think.
What's your idea ? Please help share me, Guenter
Quoted 5 lines
pwm outputs on MAX31790 are always tied to the matching tachometer inputs (pwm1 <--> tach1 etc) and can not be reconfigured, meaning tach-ch for channel X would always be X.
Quoted 9 lines
Quoted 4 lines
I would like to open a discussion about whether we should use the tach-ch property on the
fan-common.yamlI'm looking forward to hearing comments from everyone. For me, both tach-ch and vendor property are good.
I am not even sure how to define tach-ch to mean "use the pwm output pin associated with this tachometer input channel not as pwm output but as tachometer input". That would be a boolean, not a number.
Thank Guenter,
I reviewed again the "tach-ch" property, which is used in the https://elixir.bootlin.com/linux/v6.9-rc6/source/Documentation/devicetree/bindings/hwmon/aspeed,g6-pwm-tach.yaml#L68 and https://elixir.bootlin.com/linux/v6.9-rc6/source/drivers/hwmon/aspeed-g6-pwm-tach.c#L434
That is something completely different from my purpose.
Quoted 2 lines
Guenter
Guenter Roeck
maintainerRe: [PATCH v2 3/3] dt-bindings: hwmon: max31790: Add maxim,pwmout-pin-as-tach-input property
Quoted 54 lines · Chanh Nguyen
Quoted 25 lines · Guenter Roeck
Quoted 6 lines · Chanh Nguyen
Quoted 2 lines · Conor Dooley
[EXTERNAL EMAIL NOTICE: This email originated from an external sender. Please be mindful of safe email handling and proprietary information protection practices.]
The quote doesn't make much sense.
Quoted 2 lines
Sorry Conor, there may be confusion here. I mean the mapping of the PWM output to the TACH input, which is on the MAX31790, and it is not sure a common feature on all fan controllers.
I think the term "mapping" is a bit confusing here.
tach-ch, as I understand it, is supposed to associate a tachometer input with a pwm output, meaning the fan speed measured with the tachometer input is expected to change if the pwm output changes.
On MAX31790, it is possible to configure a pwm output pin as tachometer input pin. That is something completely different. Also, the association is fixed. If the first pwm channel is used as tachometer channel, it would show up as 7th tachometer channel. If the 6th pwm channel is configured to be used as tachometer input, it would show up as 12th tachometer channel.
Quoted 3 lines
Overall, the total number of channels on MAX31790 is always 12. 6 of them are always tachometer inputs, the others can be configured to either be a pwm output or a tachometer input.
Thank you, Guenter, for your explanation. That is also my understanding of the MAX31790 feature.
So, I think we should introduce a vendor property to configure the pwm output pins to become tachometer input pins. We shouldn't use the tach-ch property. Because they are completely different, I think.
What's your idea ? Please help share me, Guenter
Quoted 5 lines
pwm outputs on MAX31790 are always tied to the matching tachometer inputs (pwm1 <--> tach1 etc) and can not be reconfigured, meaning tach-ch for channel X would always be X.
Quoted 9 lines
Quoted 4 lines
I would like to open a discussion about whether we should use the tach-ch property on the
fan-common.yamlI'm looking forward to hearing comments from everyone. For me, both tach-ch and vendor property are good.
I am not even sure how to define tach-ch to mean "use the pwm output pin associated with this tachometer input channel not as pwm output but as tachometer input". That would be a boolean, not a number.
Quoted 6 lines
Thank Guenter,
I reviewed again the "tach-ch" property, which is used in the https://elixir.bootlin.com/linux/v6.9-rc6/source/Documentation/devicetree/bindings/hwmon/aspeed,g6-pwm-tach.yaml#L68 and https://elixir.bootlin.com/linux/v6.9-rc6/source/drivers/hwmon/aspeed-g6-pwm-tach.c#L434
That is something completely different from my purpose.
Based on its definition, tach-ch is associated with fans, and it looks like the .yaml file groups multiple sets of fans into a single fan node.
In the simple case that would be
tach-ch = <1> ... tach-ch = <12>
or, if all fans are controlled by a single pwm
tach-ch = <1 2 3 4 5 6 8 9 10 11 12>
The existence of tachometer channel 7..12 implies that pwm channel (tachometer channel - 6) is used as tachometer channel. That should be sufficient to program the chip for that channel. All you'd have to do is to ensure that pwm channel "X" is not listed as tachometer channel "X + 6", and program pwm channel "X - 6" for tachometer channels 7..12 as tachometer channels.
Hope this helps,
Guenter
Re: [PATCH v2 3/3] dt-bindings: hwmon: max31790: Add maxim,pwmout-pin-as-tach-input property
Quoted 71 lines · Guenter Roeck
Quoted 54 lines · Chanh Nguyen
Quoted 25 lines · Guenter Roeck
Quoted 6 lines · Chanh Nguyen
Quoted 2 lines · Conor Dooley
[EXTERNAL EMAIL NOTICE: This email originated from an external sender. Please be mindful of safe email handling and proprietary information protection practices.]
The quote doesn't make much sense.
Quoted 2 lines
Sorry Conor, there may be confusion here. I mean the mapping of the PWM output to the TACH input, which is on the MAX31790, and it is not sure a common feature on all fan controllers.
I think the term "mapping" is a bit confusing here.
tach-ch, as I understand it, is supposed to associate a tachometer input with a pwm output, meaning the fan speed measured with the tachometer input is expected to change if the pwm output changes.
On MAX31790, it is possible to configure a pwm output pin as tachometer input pin. That is something completely different. Also, the association is fixed. If the first pwm channel is used as tachometer channel, it would show up as 7th tachometer channel. If the 6th pwm channel is configured to be used as tachometer input, it would show up as 12th tachometer channel.
Quoted 3 lines
Overall, the total number of channels on MAX31790 is always 12. 6 of them are always tachometer inputs, the others can be configured to either be a pwm output or a tachometer input.
Thank you, Guenter, for your explanation. That is also my understanding of the MAX31790 feature.
So, I think we should introduce a vendor property to configure the pwm output pins to become tachometer input pins. We shouldn't use the tach-ch property. Because they are completely different, I think.
What's your idea ? Please help share me, Guenter
Quoted 5 lines
pwm outputs on MAX31790 are always tied to the matching tachometer inputs (pwm1 <--> tach1 etc) and can not be reconfigured, meaning tach-ch for channel X would always be X.
Quoted 9 lines
Quoted 4 lines
I would like to open a discussion about whether we should use the tach-ch property on the
fan-common.yamlI'm looking forward to hearing comments from everyone. For me, both tach-ch and vendor property are good.
I am not even sure how to define tach-ch to mean "use the pwm output pin associated with this tachometer input channel not as pwm output but as tachometer input". That would be a boolean, not a number.
Quoted 6 lines
Thank Guenter,
I reviewed again the "tach-ch" property, which is used in the https://elixir.bootlin.com/linux/v6.9-rc6/source/Documentation/devicetree/bindings/hwmon/aspeed,g6-pwm-tach.yaml#L68 and https://elixir.bootlin.com/linux/v6.9-rc6/source/drivers/hwmon/aspeed-g6-pwm-tach.c#L434
That is something completely different from my purpose.
Based on its definition, tach-ch is associated with fans, and it looks like the .yaml file groups multiple sets of fans into a single fan node.
In the simple case that would be
tach-ch = <1>
...
tach-ch = <12>
Quoted 9 lines
or, if all fans are controlled by a single pwm
tach-ch = <1 2 3 4 5 6 8 9 10 11 12>The existence of tachometer channel 7..12 implies that pwm channel (tachometer channel - 6) is used as tachometer channel. That should be sufficient to program the chip for that channel. All you'd have to do is to ensure that pwm channel "X" is not listed as tachometer channel "X + 6", and program pwm channel "X - 6" for tachometer channels 7..12 as tachometer channels.
Hi Guenter,
I applied the patch [2/3] in my patch series (https://lore.kernel.org/lkml/[email protected]/)
My device tree is configured as below, I would like to configure PWMOUT pins 5 and 6 to become the tachometer input pins.
fan-controller@20 {
compatible = "maxim,max31790";
reg = <0x20>;
maxim,pwmout-pin-as-tach-input = /bits/ 8 <0 0 0 0 1 1>;
};The sysfs is generated by the max31790 driver are shown below. We can see the PWM5 and PWM6 are not visible, and the fan11 and fan12 are visible. And all FAN devices are on my system, which worked as expected.
root@my-platform:/sys/class/hwmon/hwmon14# ls device fan12_input fan1_target fan2_target fan3_target fan4_target fan6_enable of_node pwm2 pwm4 fan11_fault fan1_enable fan2_enable fan3_enable fan4_enable fan5_enable fan6_fault power pwm2_enable pwm4_enable fan11_input fan1_fault fan2_fault fan3_fault fan4_fault fan5_fault fan6_input pwm1 pwm3 subsystem fan12_fault fan1_input fan2_input fan3_input fan4_input fan5_input name pwm1_enable pwm3_enable uevent
Please share your comments!
Quoted 3 lines
Hope this helps,
Guenter
Re: [PATCH v2 3/3] dt-bindings: hwmon: max31790: Add maxim,pwmout-pin-as-tach-input property
Quoted 57 lines · Chanh Nguyen
Quoted 41 lines · Guenter Roeck
Quoted 20 lines · Chanh Nguyen
Quoted 10 lines · Guenter Roeck
On 4/25/24 03:33, Chanh Nguyen wrote:
pwm outputs on MAX31790 are always tied to the matching tachometer inputs
(pwm1 <--> tach1 etc) and can not be reconfigured, meaning tach-ch for channel X would always be X.Quoted 3 lines
I would like to open a discussion about whether we should use the tach-ch property on the
fan-common.yamlQuoted 8 lines
Quoted 3 lines
I'm looking forward to hearing comments from everyone. For me, both tach-ch and vendor property are good.
I am not even sure how to define tach-ch to mean "use the pwm output pin associated with this tachometer input channel not as pwm output but as tachometer input". That would be a boolean, not a number.
Quoted 7 lines
Thank Guenter,
I reviewed again the "tach-ch" property, which is used in the https://elixir.bootlin.com/linux/v6.9-rc6/source/Documentation/devicetree/bindings/hwmon/aspeed,g6-pwm-tach.yaml#L68
and https://elixir.bootlin.com/linux/v6.9-rc6/source/drivers/hwmon/aspeed-g6-pwm-tach.c#L434That is something completely different from my purpose.
Based on its definition, tach-ch is associated with fans, and it looks like the .yaml file groups multiple sets of fans into a single fan node.
In the simple case that would be
tach-ch = <1>
...
tach-ch = <12>or, if all fans are controlled by a single pwm
tach-ch = <1 2 3 4 5 6 8 9 10 11 12>Quoted 10 lines
The existence of tachometer channel 7..12 implies that pwm channel (tachometer
channel - 6) is used as tachometer channel. That should be sufficient to program
the chip for that channel. All you'd have to do is to ensure that pwm channel
"X" is not listed as tachometer channel "X + 6", and program pwm channel "X - 6"
for tachometer channels 7..12 as tachometer channels.Hi Guenter,
I applied the patch [2/3] in my patch series (https://lore.kernel.org/lkml/[email protected]/)
Quoted 8 lines
My device tree is configured as below, I would like to configure PWMOUT pins 5 and 6 to become the tachometer input pins.
fan-controller@20 { compatible = "maxim,max31790"; reg = <0x20>; maxim,pwmout-pin-as-tach-input = /bits/ 8 <0 0 0 0 1 1>; };
Why are you still operating off a binding that looks like this? I thought that both I and Krzysztof told you to go and take a look at how the aspeed,g6-pwm-tach.yaml binding looped and do something similar here. You'd end up with something like:
fan-controller@20 {
compatible = "maxim,max31790";
reg = <0x20>;
fan-0 {
pwms = <&pwm-provider ...>;
tach-ch = 6;
};
fan-1 {
pwms = <&pwm-provider ...>;
tach-ch = 7;
};
};You can, as tach-ch or pwms do not need to be unique, set multiple channels up as using the same tachs and/or pwms.
In the case of this particular fan controller, I think that the max31790 is actually the pwm provider so you'd modify it something like:
pwm-provider: fan-controller@20 {
compatible = "maxim,max31790";
reg = <0x20>;
#pwm-cells = <N>;
fan-0 {
pwms = <&pwm-provider ...>;
tach-ch = <6>;
};
fan-1 {
pwms = <&pwm-provider ...>;
tach-ch = <7>;
};
};I just wrote this in my mail client's editor, so it may not be not valid, but it is how the fan bindings expect you to represent this kind of scenario.
Cheers,
Conor.
Quoted 20 lines
The sysfs is generated by the max31790 driver are shown below. We can see the PWM5 and PWM6 are not visible, and the fan11 and fan12 are visible. And all FAN devices are on my system, which worked as expected.
root@my-platform:/sys/class/hwmon/hwmon14# ls device fan12_input fan1_target fan2_target fan3_target fan4_target fan6_enable of_node pwm2 pwm4 fan11_fault fan1_enable fan2_enable fan3_enable fan4_enable fan5_enable fan6_fault power pwm2_enable pwm4_enable fan11_input fan1_fault fan2_fault fan3_fault fan4_fault fan5_fault fan6_input pwm1 pwm3 subsystem fan12_fault fan1_input fan2_input fan3_input fan4_input fan5_input name pwm1_enable pwm3_enable ueventPlease share your comments!
Quoted 3 lines
Hope this helps,
Guenter
Re: [PATCH v2 3/3] dt-bindings: hwmon: max31790: Add maxim,pwmout-pin-as-tach-input property
Quoted 108 lines · Conor Dooley
Quoted 57 lines · Chanh Nguyen
Quoted 41 lines · Guenter Roeck
Quoted 20 lines · Chanh Nguyen
Quoted 10 lines · Guenter Roeck
On 4/25/24 03:33, Chanh Nguyen wrote:
pwm outputs on MAX31790 are always tied to the matching tachometer inputs
(pwm1 <--> tach1 etc) and can not be reconfigured, meaning tach-ch for channel X would always be X.Quoted 3 lines
I would like to open a discussion about whether we should use the tach-ch property on the
fan-common.yamlQuoted 8 lines
Quoted 3 lines
I'm looking forward to hearing comments from everyone. For me, both tach-ch and vendor property are good.
I am not even sure how to define tach-ch to mean "use the pwm output pin associated with this tachometer input channel not as pwm output but as tachometer input". That would be a boolean, not a number.
Quoted 7 lines
Thank Guenter,
I reviewed again the "tach-ch" property, which is used in the https://elixir.bootlin.com/linux/v6.9-rc6/source/Documentation/devicetree/bindings/hwmon/aspeed,g6-pwm-tach.yaml#L68
and https://elixir.bootlin.com/linux/v6.9-rc6/source/drivers/hwmon/aspeed-g6-pwm-tach.c#L434That is something completely different from my purpose.
Based on its definition, tach-ch is associated with fans, and it looks like the .yaml file groups multiple sets of fans into a single fan node.
In the simple case that would be
tach-ch = <1>
...
tach-ch = <12>or, if all fans are controlled by a single pwm
tach-ch = <1 2 3 4 5 6 8 9 10 11 12>Quoted 10 lines
The existence of tachometer channel 7..12 implies that pwm channel (tachometer
channel - 6) is used as tachometer channel. That should be sufficient to program
the chip for that channel. All you'd have to do is to ensure that pwm channel
"X" is not listed as tachometer channel "X + 6", and program pwm channel "X - 6"
for tachometer channels 7..12 as tachometer channels.Hi Guenter,
I applied the patch [2/3] in my patch series (https://lore.kernel.org/lkml/[email protected]/)
Quoted 8 lines
My device tree is configured as below, I would like to configure PWMOUT pins 5 and 6 to become the tachometer input pins.
fan-controller@20 { compatible = "maxim,max31790"; reg = <0x20>; maxim,pwmout-pin-as-tach-input = /bits/ 8 <0 0 0 0 1 1>; };Why are you still operating off a binding that looks like this? I thought that both I and Krzysztof told you to go and take a look at how the aspeed,g6-pwm-tach.yaml binding looped and do something similar here. You'd end up with something like:
fan-controller@20 { compatible = "maxim,max31790"; reg = <0x20>; fan-0 { pwms = <&pwm-provider ...>; tach-ch = 6; }; fan-1 { pwms = <&pwm-provider ...>; tach-ch = 7; }; };You can, as tach-ch or pwms do not need to be unique, set multiple channels up as using the same tachs and/or pwms.
In the case of this particular fan controller, I think that the max31790 is actually the pwm provider so you'd modify it something like:pwm-provider: fan-controller@20 { compatible = "maxim,max31790"; reg = <0x20>; #pwm-cells = <N>; fan-0 { pwms = <&pwm-provider ...>; tach-ch = <6>; }; fan-1 { pwms = <&pwm-provider ...>; tach-ch = <7>; }; };
Quoted 4 lines
I just wrote this in my mail client's editor, so it may not be not valid, but it is how the fan bindings expect you to represent this kind of scenario.
My apologies for the late reply.
Thank you, Conor, for your recommendation!
I spend more time checking the aspeed,g6-pwm-tach.yaml . Finally, I'll support the child nodes by having different tach-ch values. My system is designed similar to Figure 6 (8 Tach Monitors, 4PMWs).
I'm going to push the patch series v3 soon.
This is a brief binding.
....
properties:
compatible:
const: maxim,max31790
reg:
maxItems: 1
clocks:
maxItems: 1
resets:
maxItems: 1
patternProperties:
"^fan-[0-9]+$":
$ref: fan-common.yaml#
unevaluatedProperties: false
required:
- compatible
- reg
additionalProperties: false
examples:
- |
i2c {
#address-cells = <1>;
#size-cells = <0>;
pwm_provider: fan-controller@20 {
compatible = "maxim,max31790";
reg = <0x20>;
clocks = <&sys_clk>;
resets = <&reset 0>;
fan-0 {
pwms = <&pwm_provider 1>;
tach-ch = <1 2>;
};
fan-1 {
pwms = <&pwm_provider 2>;
tach-ch = <7 8>;
};
};
};
As your example, I saw the #pwm-cells = <N> . Please let me know, what's the purpose of this property?
Thanks!
Chanh Ng
Quoted 23 lines
Cheers,
Conor.Quoted 20 lines
The sysfs is generated by the max31790 driver are shown below. We can see the PWM5 and PWM6 are not visible, and the fan11 and fan12 are visible. And all FAN devices are on my system, which worked as expected.
root@my-platform:/sys/class/hwmon/hwmon14# ls device fan12_input fan1_target fan2_target fan3_target fan4_target fan6_enable of_node pwm2 pwm4 fan11_fault fan1_enable fan2_enable fan3_enable fan4_enable fan5_enable fan6_fault power pwm2_enable pwm4_enable fan11_input fan1_fault fan2_fault fan3_fault fan4_fault fan5_fault fan6_input pwm1 pwm3 subsystem fan12_fault fan1_input fan2_input fan3_input fan4_input fan5_input name pwm1_enable pwm3_enable ueventPlease share your comments!
Quoted 3 lines
Hope this helps,
Guenter
Guenter Roeck
maintainerRe: [PATCH v2 3/3] dt-bindings: hwmon: max31790: Add maxim,pwmout-pin-as-tach-input property
Quoted 175 lines · Chanh Nguyen
Quoted 108 lines · Conor Dooley
Quoted 57 lines · Chanh Nguyen
Quoted 41 lines · Guenter Roeck
Quoted 20 lines · Chanh Nguyen
Quoted 10 lines · Guenter Roeck
On 4/25/24 03:33, Chanh Nguyen wrote:
pwm outputs on MAX31790 are always tied to the matching tachometer inputs
(pwm1 <--> tach1 etc) and can not be reconfigured, meaning tach-ch for channel X would always be X.Quoted 3 lines
I would like to open a discussion about whether we should use the tach-ch property on the
fan-common.yamlQuoted 8 lines
Quoted 3 lines
I'm looking forward to hearing comments from everyone. For me, both tach-ch and vendor property are good.
I am not even sure how to define tach-ch to mean "use the pwm output pin associated with this tachometer input channel not as pwm output but as tachometer input". That would be a boolean, not a number.
Quoted 7 lines
Thank Guenter,
I reviewed again the "tach-ch" property, which is used in the https://elixir.bootlin.com/linux/v6.9-rc6/source/Documentation/devicetree/bindings/hwmon/aspeed,g6-pwm-tach.yaml#L68
and https://elixir.bootlin.com/linux/v6.9-rc6/source/drivers/hwmon/aspeed-g6-pwm-tach.c#L434That is something completely different from my purpose.
Based on its definition, tach-ch is associated with fans, and it looks like the .yaml file groups multiple sets of fans into a single fan node.
In the simple case that would be
tach-ch = <1>
...
tach-ch = <12>or, if all fans are controlled by a single pwm
tach-ch = <1 2 3 4 5 6 8 9 10 11 12>Quoted 10 lines
The existence of tachometer channel 7..12 implies that pwm channel (tachometer
channel - 6) is used as tachometer channel. That should be sufficient to program
the chip for that channel. All you'd have to do is to ensure that pwm channel
"X" is not listed as tachometer channel "X + 6", and program pwm channel "X - 6"
for tachometer channels 7..12 as tachometer channels.Hi Guenter,
I applied the patch [2/3] in my patch series (https://lore.kernel.org/lkml/[email protected]/)
Quoted 8 lines
My device tree is configured as below, I would like to configure PWMOUT pins 5 and 6 to become the tachometer input pins.
fan-controller@20 {
compatible = "maxim,max31790";
reg = <0x20>;
maxim,pwmout-pin-as-tach-input = /bits/ 8 <0 0 0 0 1 1>; };Why are you still operating off a binding that looks like this? I thought that both I and Krzysztof told you to go and take a look at how the aspeed,g6-pwm-tach.yaml binding looped and do something similar here. You'd end up with something like:
fan-controller@20 {
compatible = "maxim,max31790";
reg = <0x20>;fan-0 {
pwms = <&pwm-provider ...>;
tach-ch = 6;
};fan-1 {
pwms = <&pwm-provider ...>;
tach-ch = 7;
};
};You can, as tach-ch or pwms do not need to be unique, set multiple channels up as using the same tachs and/or pwms.
In the case of this particular fan controller, I think that the max31790 is actually the pwm provider so you'd modify it something like:pwm-provider: fan-controller@20 {
compatible = "maxim,max31790";
reg = <0x20>;
#pwm-cells = <N>;fan-0 {
pwms = <&pwm-provider ...>;
tach-ch = <6>;
};fan-1 {
pwms = <&pwm-provider ...>;
tach-ch = <7>;
};
};Quoted 4 lines
I just wrote this in my mail client's editor, so it may not be not valid, but it is how the fan bindings expect you to represent this kind of scenario.
My apologies for the late reply.
Thank you, Conor, for your recommendation!
I spend more time checking the aspeed,g6-pwm-tach.yaml . Finally, I'll support the child nodes by having different tach-ch values. My system is designed similar to Figure 6 (8 Tach Monitors, 4PMWs).
I'm going to push the patch series v3 soon.
This is a brief binding.
....
properties:
compatible:
const: maxim,max31790reg:
maxItems: 1clocks:
maxItems: 1resets:
maxItems: 1patternProperties:
"^fan-[0-9]+$":
$ref: fan-common.yaml#
unevaluatedProperties: falserequired:
- compatible
- regadditionalProperties: false
examples:
- |
i2c {
#address-cells = <1>;
#size-cells = <0>;
pwm_provider: fan-controller@20 {
compatible = "maxim,max31790";
reg = <0x20>;
clocks = <&sys_clk>;
resets = <&reset 0>;fan-0 {
pwms = <&pwm_provider1>;
tach-ch = <1 2>;
};fan-1 {
pwms = <&pwm_provider2>;
tach-ch = <7 8>;
};
};
};
Quoted 2 lines
As your example, I saw the #pwm-cells = <N> . Please let me know, what's the purpose of this property?
It is the number of fields in "pwms" after the provider reference. In your case it would be 1 (the index). If the pwm has additional configuration parameters such as the frequency or polarity there would be additional entries.
Guenter
Re: [PATCH v2 3/3] dt-bindings: hwmon: max31790: Add maxim,pwmout-pin-as-tach-input property
Quoted 176 lines · Guenter Roeck
Quoted 175 lines · Chanh Nguyen
Quoted 108 lines · Conor Dooley
Quoted 57 lines · Chanh Nguyen
Quoted 41 lines · Guenter Roeck
Quoted 20 lines · Chanh Nguyen
Quoted 10 lines · Guenter Roeck
On 4/25/24 03:33, Chanh Nguyen wrote:
pwm outputs on MAX31790 are always tied to the matching tachometer inputs
(pwm1 <--> tach1 etc) and can not be reconfigured, meaning tach-ch for channel X would always be X.Quoted 3 lines
I would like to open a discussion about whether we should use the tach-ch property on the
fan-common.yamlQuoted 8 lines
Quoted 3 lines
I'm looking forward to hearing comments from everyone. For me, both tach-ch and vendor property are good.
I am not even sure how to define tach-ch to mean "use the pwm output pin associated with this tachometer input channel not as pwm output but as tachometer input". That would be a boolean, not a number.
Quoted 7 lines
Thank Guenter,
I reviewed again the "tach-ch" property, which is used in the https://elixir.bootlin.com/linux/v6.9-rc6/source/Documentation/devicetree/bindings/hwmon/aspeed,g6-pwm-tach.yaml#L68
and https://elixir.bootlin.com/linux/v6.9-rc6/source/drivers/hwmon/aspeed-g6-pwm-tach.c#L434That is something completely different from my purpose.
Based on its definition, tach-ch is associated with fans, and it looks like the .yaml file groups multiple sets of fans into a single fan node.
In the simple case that would be
tach-ch = <1>
...
tach-ch = <12>or, if all fans are controlled by a single pwm
tach-ch = <1 2 3 4 5 6 8 9 10 11 12>Quoted 10 lines
The existence of tachometer channel 7..12 implies that pwm channel (tachometer
channel - 6) is used as tachometer channel. That should be sufficient to program
the chip for that channel. All you'd have to do is to ensure that pwm channel
"X" is not listed as tachometer channel "X + 6", and program pwm channel "X - 6"
for tachometer channels 7..12 as tachometer channels.Hi Guenter,
I applied the patch [2/3] in my patch series (https://lore.kernel.org/lkml/[email protected]/)
Quoted 8 lines
My device tree is configured as below, I would like to configure PWMOUT pins 5 and 6 to become the tachometer input pins.
fan-controller@20 {
compatible = "maxim,max31790";
reg = <0x20>;
maxim,pwmout-pin-as-tach-input = /bits/ 8 <0 0 0 0 1 1>; };Why are you still operating off a binding that looks like this? I thought that both I and Krzysztof told you to go and take a look at how the aspeed,g6-pwm-tach.yaml binding looped and do something similar here. You'd end up with something like:
fan-controller@20 {
compatible = "maxim,max31790";
reg = <0x20>;fan-0 {
pwms = <&pwm-provider ...>;
tach-ch = 6;
};fan-1 {
pwms = <&pwm-provider ...>;
tach-ch = 7;
};
};You can, as tach-ch or pwms do not need to be unique, set multiple channels up as using the same tachs and/or pwms.
In the case of this particular fan controller, I think that the max31790 is actually the pwm provider so you'd modify it something like:pwm-provider: fan-controller@20 {
compatible = "maxim,max31790";
reg = <0x20>;
#pwm-cells = <N>;fan-0 {
pwms = <&pwm-provider ...>;
tach-ch = <6>;
};fan-1 {
pwms = <&pwm-provider ...>;
tach-ch = <7>;
};
};Quoted 4 lines
I just wrote this in my mail client's editor, so it may not be not valid, but it is how the fan bindings expect you to represent this kind of scenario.
My apologies for the late reply.
Thank you, Conor, for your recommendation!
I spend more time checking the aspeed,g6-pwm-tach.yaml . Finally, I'll support the child nodes by having different tach-ch values. My system is designed similar to Figure 6 (8 Tach Monitors, 4PMWs).
I'm going to push the patch series v3 soon.
This is a brief binding.
....
properties:
compatible:
const: maxim,max31790reg:
maxItems: 1clocks:
maxItems: 1resets:
maxItems: 1patternProperties:
"^fan-[0-9]+$":
$ref: fan-common.yaml#
unevaluatedProperties: falserequired:
- compatible
- regadditionalProperties: false
examples:
- |
i2c {
#address-cells = <1>;
#size-cells = <0>;
pwm_provider: fan-controller@20 {
compatible = "maxim,max31790";
reg = <0x20>;
clocks = <&sys_clk>;
resets = <&reset 0>;fan-0 {
pwms = <&pwm_provider1>;
tach-ch = <1 2>;
};fan-1 {
pwms = <&pwm_provider2>;
tach-ch = <7 8>;
};
};
};
Quoted 8 lines
Quoted 2 lines
As your example, I saw the #pwm-cells = <N> . Please let me know, what's the purpose of this property?
It is the number of fields in "pwms" after the provider reference. In your case it would be 1 (the index). If the pwm has additional configuration parameters such as the frequency or polarity there would be additional entries.
Thank Guenter very much!
Please help review my binding. I'm looking forward to hearing any of your comments.
I'll update all comments on patch series v3 and push for review soon.
The patch series includes two commits:
[PATH 1/2] dt-bindings: hwmon: Add maxim max31790
[PATH 2/2] hwmon: (max31790): Support config PWM becomes TACH by tach-ch
Thanks,
Chanh Ng
Quoted 2 lines
Guenter
Re: [PATCH v2 3/3] dt-bindings: hwmon: max31790: Add maxim,pwmout-pin-as-tach-input property
In reply to Chanh NguyenQuoted 38 lines · Chanh Nguyen
Quoted 27 lines
Quoted 7 lines
Quoted 6 lines
Quoted 1 line
I am not even sure how to define tach-ch to mean "use the pwm output pin associated with this tachometer input channel not as pwm output but as tachometer input". That would be a boolean, not a number.
Quoted 7 lines
Thank Guenter,
I reviewed again the "tach-ch" property, which is used in the
https://elixir.bootlin.com/linux/v6.9-rc6/source/Documentation/devicetree/bindings/hwmon/aspeed,g6-pwm-tach.yaml#L68 and https://elixir.bootlin.com/linux/v6.9-rc6/source/drivers/hwmon/aspeed-g6-pwm-tach.c#L434That is something completely different from my purpose.
Based on its definition, tach-ch is associated with fans, and it looks like the .yaml file groups multiple sets of fans into a single fan node.
In the simple case that would be
tach-ch = <1>
...
tach-ch = <12>or, if all fans are controlled by a single pwm
tach-ch = <1 2 3 4 5 6 8 9 10 11 12>Quoted 10 lines
The existence of tachometer channel 7..12 implies that pwm channel (tachometer
channel - 6) is used as tachometer channel. That should be sufficient to program
the chip for that channel. All you'd have to do is to ensure that pwm channel
"X" is not listed as tachometer channel "X + 6", and program pwm channel "X - 6"
for tachometer channels 7..12 as tachometer channels.
Quoted 8 lines
Hi Guenter,
I applied the patch [2/3] in my patch series
(https://lore.kernel.org/lkml/[email protected]/)My device tree is configured as below, I would like to configure PWMOUT pins 5 and 6 to become the tachometer input pins.
And what is wrong in described common tach-ch property? I think we explained it three times and you did not provide any arguments, what's missing. Instead you say "I want something like this in DTS" which is not an argument and does not help discussion.
Best regards,
Krzysztof
Re: [PATCH v2 3/3] dt-bindings: hwmon: max31790: Add maxim,pwmout-pin-as-tach-input property
Quoted 44 lines · Krzysztof Kozlowski
Quoted 43 lines · Chanh Nguyen
Quoted 27 lines
Quoted 7 lines
Quoted 6 lines
Quoted 1 line
I am not even sure how to define tach-ch to mean "use the pwm output pin associated with this tachometer input channel not as pwm output but as tachometer input". That would be a boolean, not a number.
Quoted 7 lines
Thank Guenter,
I reviewed again the "tach-ch" property, which is used in the
https://elixir.bootlin.com/linux/v6.9-rc6/source/Documentation/devicetree/bindings/hwmon/aspeed,g6-pwm-tach.yaml#L68 and https://elixir.bootlin.com/linux/v6.9-rc6/source/drivers/hwmon/aspeed-g6-pwm-tach.c#L434That is something completely different from my purpose.
Based on its definition, tach-ch is associated with fans, and it looks like the .yaml file groups multiple sets of fans into a single fan node.
In the simple case that would be
tach-ch = <1>
...
tach-ch = <12>or, if all fans are controlled by a single pwm
tach-ch = <1 2 3 4 5 6 8 9 10 11 12>Quoted 10 lines
The existence of tachometer channel 7..12 implies that pwm channel (tachometer
channel - 6) is used as tachometer channel. That should be sufficient to program
the chip for that channel. All you'd have to do is to ensure that pwm channel
"X" is not listed as tachometer channel "X + 6", and program pwm channel "X - 6"
for tachometer channels 7..12 as tachometer channels.Hi Guenter,
I applied the patch [2/3] in my patch series
(https://lore.kernel.org/lkml/[email protected]/)
Quoted 9 lines
Quoted 3 lines
My device tree is configured as below, I would like to configure PWMOUT pins 5 and 6 to become the tachometer input pins.
And what is wrong in described common tach-ch property? I think we explained it three times and you did not provide any arguments, what's missing. Instead you say "I want something like this in DTS" which is not an argument and does not help discussion.
Hi Krzysztof,
Apologies for any inconvenience caused by the delayed response.
I'll to support the child nodes by having different tach-ch values. I suggest the child nodes and the "tach-ch" is optional, it will not be added to "required:". Do you have any comments? Please help me share!
This is a brief binding
...
properties:
compatible:
const: maxim,max31790
reg:
maxItems: 1
clocks:
maxItems: 1
resets:
maxItems: 1
patternProperties:
"^fan-[0-9]+$":
$ref: fan-common.yaml#
unevaluatedProperties: false
required:
- compatible
- reg
additionalProperties: false
examples:
- |
i2c {
#address-cells = <1>;
#size-cells = <0>;
pwm_provider: fan-controller@20 {
compatible = "maxim,max31790";
reg = <0x20>;
clocks = <&sys_clk>;
resets = <&reset 0>;
fan-0 {
pwms = <&pwm_provider 1>;
tach-ch = <1 2>;
};
fan-1 {
pwms = <&pwm_provider 2>;
tach-ch = <7 8>;
};
};
};
If it's OK, I'm going to push the patch series v3 soon.
Thanks,
Chanh Ng
Quoted 3 lines
Best regards,
Krzysztof