6.1.88-rc1 review

6.1-stable review patch. If anyone has any objections, please let me know.

------------------

From: Coia Prant <[email protected]>

commit cf16ffa17c398434a77b8a373e69287c95b60de2 upstream.

Update the USB serial option driver to support Longsung U8300/U9300.

For U8300

Interface 4 is used by for QMI interface in stock firmware of U8300, the router which uses U8300 modem.
Interface 5 is used by for ADB interface in stock firmware of U8300, the router which uses U8300 modem.

Interface mapping is:
0: unknown (Debug), 1: AT (Modem), 2: AT, 3: PPP (NDIS / Pipe), 4: QMI, 5: ADB

T:  Bus=05 Lev=01 Prnt=03 Port=02 Cnt=01 Dev#=  4 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1c9e ProdID=9b05 Rev=03.18
S:  Manufacturer=Android
S:  Product=Android
C:  #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=83(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=85(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=87(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
I:  If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=89(I) Atr=03(Int.) MxPS=   8 Ivl=32ms
I:  If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E:  Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

For U9300

Interface 1 is used by for ADB interface in stock firmware of U9300, the router which uses U9300 modem.
Interface 4 is used by for QMI interface in stock firmware of U9300, the router which uses U9300 modem.

Interface mapping is:
0: ADB, 1: AT (Modem), 2: AT, 3: PPP (NDIS / Pipe), 4: QMI

Note: Interface 3 of some models of the U9300 series can send AT commands.

T:  Bus=05 Lev=01 Prnt=05 Port=04 Cnt=01 Dev#=  6 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1c9e ProdID=9b3c Rev=03.18
S:  Manufacturer=Android
S:  Product=Android
C:  #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=83(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=85(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=87(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
I:  If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=89(I) Atr=03(Int.) MxPS=   8 Ivl=32ms

Tested successfully using Modem Manager on U9300.
Tested successfully AT commands using If=1, If=2 and If=3 on U9300.

---
 drivers/usb/serial/option.c |    4 ++++
 1 file changed, 4 insertions(+)

@@ -2052,6 +2052,10 @@ static const struct usb_device_id option
 	  .driver_info = RSVD(3) },
 	{ USB_DEVICE_INTERFACE_CLASS(LONGCHEER_VENDOR_ID, 0x9803, 0xff),
 	  .driver_info = RSVD(4) },
+	{ USB_DEVICE(LONGCHEER_VENDOR_ID, 0x9b05),	/* Longsung U8300 */
+	  .driver_info = RSVD(4) | RSVD(5) },
+	{ USB_DEVICE(LONGCHEER_VENDOR_ID, 0x9b3c),	/* Longsung U9300 */
+	  .driver_info = RSVD(0) | RSVD(4) },
 	{ USB_DEVICE(LONGCHEER_VENDOR_ID, ZOOM_PRODUCT_4597) },
 	{ USB_DEVICE(LONGCHEER_VENDOR_ID, IBALL_3_5G_CONNECT) },
 	{ USB_DEVICE(HAIER_VENDOR_ID, HAIER_PRODUCT_CE100) },

6.1-stable review patch. If anyone has any objections, please let me know.

------------------

From: Jerry Meng <[email protected]>

commit c840244aba7ad2b83ed904378b36bd6aef25511c upstream.

EM060K_129, EM060K_12a, EM060K_12b and EM0060K_12c are EM060K's sub-models, having the same name "Quectel EM060K-GL" and the same interface layout.

MBIM + GNSS + DIAG + NMEA + AT + QDSS + DPL

T:  Bus=03 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#=  8 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=2c7c ProdID=0129 Rev= 5.04
S:  Manufacturer=Quectel
S:  Product=Quectel EM060K-GL
S:  SerialNumber=f6fa08b6
C:* #Ifs= 8 Cfg#= 1 Atr=a0 MxPwr=500mA
A:  FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim
E:  Ad=81(I) Atr=03(Int.) MxPS=  64 Ivl=32ms
I:  If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E:  Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=0f(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=82(I) Atr=03(Int.) MxPS=  64 Ivl=32ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=40 Driver=option
E:  Ad=85(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E:  Ad=87(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms

I:* If#= 6 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=70 Driver=(none)
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 7 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=80 Driver=(none)
E: Ad=8f(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

---
 drivers/usb/serial/option.c |   16 ++++++++++++++++
 1 file changed, 16 insertions(+)

@@ -255,6 +255,10 @@ static void option_instat_callback(struc
 #define QUECTEL_PRODUCT_EM061K_LMS		0x0124
 #define QUECTEL_PRODUCT_EC25			0x0125
 #define QUECTEL_PRODUCT_EM060K_128		0x0128
+#define QUECTEL_PRODUCT_EM060K_129		0x0129
+#define QUECTEL_PRODUCT_EM060K_12a		0x012a
+#define QUECTEL_PRODUCT_EM060K_12b		0x012b
+#define QUECTEL_PRODUCT_EM060K_12c		0x012c
 #define QUECTEL_PRODUCT_EG91			0x0191
 #define QUECTEL_PRODUCT_EG95			0x0195
 #define QUECTEL_PRODUCT_BG96			0x0296

@@ -1218,6 +1222,18 @@ static const struct usb_device_id option
 	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K_128, 0xff, 0xff, 0x30) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K_128, 0xff, 0x00, 0x40) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K_128, 0xff, 0xff, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K_129, 0xff, 0xff, 0x30) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K_129, 0xff, 0x00, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K_129, 0xff, 0xff, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K_12a, 0xff, 0xff, 0x30) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K_12a, 0xff, 0x00, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K_12a, 0xff, 0xff, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K_12b, 0xff, 0xff, 0x30) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K_12b, 0xff, 0x00, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K_12b, 0xff, 0xff, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K_12c, 0xff, 0xff, 0x30) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K_12c, 0xff, 0x00, 0x40) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K_12c, 0xff, 0xff, 0x40) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM061K_LCN, 0xff, 0xff, 0x30) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM061K_LCN, 0xff, 0x00, 0x40) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM061K_LCN, 0xff, 0xff, 0x40) },

6.1-stable review patch. If anyone has any objections, please let me know.

------------------

From: Vanillan Wang <[email protected]>

commit 311f97a4c7c22a01f8897bddf00428dfd0668e79 upstream.

Update the USB serial option driver support for the Rolling LTE modules.

- VID:PID 33f8:01a2, RW101-GL for laptop debug M.2 cards(with MBIM interface for /Linux/Chrome OS)
0x01a2: mbim, diag, at, pipe
- VID:PID 33f8:01a3, RW101-GL for laptop debug M.2 cards(with MBIM interface for /Linux/Chrome OS)
0x01a3: mbim, pipe
- VID:PID 33f8:01a4, RW101-GL for laptop debug M.2 cards(with MBIM interface for /Linux/Chrome OS)
0x01a4: mbim, diag, at, pipe
- VID:PID 33f8:0104, RW101-GL for laptop debug M.2 cards(with RMNET interface for /Linux/Chrome OS)
0x0104: RMNET, diag, at, pipe
- VID:PID 33f8:0115, RW135-GL for laptop debug M.2 cards(with MBIM interface for /Linux/Chrome OS)
0x0115: MBIM, diag, at, pipe

Here are the outputs of usb-devices:

T:  Bus=01 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#=  5 Spd=480 MxCh= 0
D:  Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=33f8 ProdID=01a2 Rev=05.15
S:  Manufacturer=Rolling Wireless S.a.r.l.
S:  Product=Rolling Module
S:  SerialNumber=12345678
C:  #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
E:  Ad=82(I) Atr=03(Int.) MxPS=  64 Ivl=32ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=84(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
I:  If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

T:  Bus=01 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#=  8 Spd=480 MxCh= 0
D:  Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=33f8 ProdID=01a3 Rev=05.15
S:  Manufacturer=Rolling Wireless S.a.r.l.
S:  Product=Rolling Module
S:  SerialNumber=12345678
C:  #Ifs= 3 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
E:  Ad=82(I) Atr=03(Int.) MxPS=  64 Ivl=32ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

T:  Bus=01 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 17 Spd=480 MxCh= 0
D:  Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=33f8 ProdID=01a4 Rev=05.15
S:  Manufacturer=Rolling Wireless S.a.r.l.
S:  Product=Rolling Module
S:  SerialNumber=12345678
C:  #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
E:  Ad=82(I) Atr=03(Int.) MxPS=  64 Ivl=32ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=85(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
I:  If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

T:  Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=5000 MxCh= 0
D:  Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs=  1
P:  Vendor=33f8 ProdID=0104 Rev=05.04
S:  Manufacturer=Rolling Wireless S.a.r.l.
S:  Product=Rolling Module
S:  SerialNumber=ba2eb033
C:  #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=896mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E:  Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E:  Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:  If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E:  Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E:  Ad=83(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E:  Ad=03(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E:  Ad=84(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E:  Ad=85(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=40 Driver=option
E:  Ad=04(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E:  Ad=86(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E:  Ad=87(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
I:  If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E:  Ad=0f(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E:  Ad=88(I) Atr=03(Int.) MxPS=   8 Ivl=32ms
E:  Ad=8e(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:  If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
E:  Ad=05(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E:  Ad=89(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms

T:  Bus=01 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 16 Spd=480 MxCh= 0
D:  Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=33f8 ProdID=0115 Rev=05.15
S:  Manufacturer=Rolling Wireless S.a.r.l.
S:  Product=Rolling Module
S:  SerialNumber=12345678
C:  #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
E:  Ad=82(I) Atr=03(Int.) MxPS=  64 Ivl=32ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=85(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
I:  If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

---
 drivers/usb/serial/option.c |    8 ++++++++
 1 file changed, 8 insertions(+)

@@ -2307,6 +2307,14 @@ static const struct usb_device_id option
 	{ USB_DEVICE_INTERFACE_CLASS(0x305a, 0x1404, 0xff) },			/* GosunCn GM500 RNDIS */
 	{ USB_DEVICE_INTERFACE_CLASS(0x305a, 0x1405, 0xff) },			/* GosunCn GM500 MBIM */
 	{ USB_DEVICE_INTERFACE_CLASS(0x305a, 0x1406, 0xff) },			/* GosunCn GM500 ECM/NCM */
+	{ USB_DEVICE(0x33f8, 0x0104),						/* Rolling RW101-GL (laptop RMNET) */
+	  .driver_info = RSVD(4) | RSVD(5) },
+	{ USB_DEVICE_INTERFACE_CLASS(0x33f8, 0x01a2, 0xff) },			/* Rolling RW101-GL (laptop MBIM) */
+	{ USB_DEVICE_INTERFACE_CLASS(0x33f8, 0x01a3, 0xff) },			/* Rolling RW101-GL (laptop MBIM) */
+	{ USB_DEVICE_INTERFACE_CLASS(0x33f8, 0x01a4, 0xff),			/* Rolling RW101-GL (laptop MBIM) */
+	  .driver_info = RSVD(4) },
+	{ USB_DEVICE_INTERFACE_CLASS(0x33f8, 0x0115, 0xff),			/* Rolling RW135-GL (laptop MBIM) */
+	  .driver_info = RSVD(5) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(OPPO_VENDOR_ID, OPPO_PRODUCT_R11, 0xff, 0xff, 0x30) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(SIERRA_VENDOR_ID, SIERRA_PRODUCT_EM9191, 0xff, 0xff, 0x30) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(SIERRA_VENDOR_ID, SIERRA_PRODUCT_EM9191, 0xff, 0xff, 0x40) },

6.1-stable review patch. If anyone has any objections, please let me know.

------------------

From: Daniele Palmas <[email protected]>

commit 582ee2f9d268d302595db3e36b985e5cbb93284d upstream.

Add the following Telit FN920C04 compositions:

0x10a0: rmnet + tty (AT/NMEA) + tty (AT) + tty (diag)

T:  Bus=03 Lev=01 Prnt=03 Port=06 Cnt=01 Dev#=  5 Spd=480  MxCh= 0
D:  Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1bc7 ProdID=10a0 Rev=05.15
S:  Manufacturer=Telit Cinterion
S:  Product=FN920
S:  SerialNumber=92c4c4d8
C:  #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=82(I) Atr=03(Int.) MxPS=   8 Ivl=32ms
I:  If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=84(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=86(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
I:  If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

0x10a4: rmnet + tty (AT) + tty (AT) + tty (diag)

T:  Bus=03 Lev=01 Prnt=03 Port=06 Cnt=01 Dev#=  8 Spd=480  MxCh= 0
D:  Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1bc7 ProdID=10a4 Rev=05.15
S:  Manufacturer=Telit Cinterion
S:  Product=FN920
S:  SerialNumber=92c4c4d8
C:  #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=82(I) Atr=03(Int.) MxPS=   8 Ivl=32ms
I:  If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=84(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=86(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
I:  If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

0x10a9: rmnet + tty (AT) + tty (diag) + DPL (data packet logging) + adb

T:  Bus=03 Lev=01 Prnt=03 Port=06 Cnt=01 Dev#=  9 Spd=480  MxCh= 0
D:  Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1bc7 ProdID=10a9 Rev=05.15
S:  Manufacturer=Telit Cinterion
S:  Product=FN920
S:  SerialNumber=92c4c4d8
C:  #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=82(I) Atr=03(Int.) MxPS=   8 Ivl=32ms
I:  If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=84(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
I:  If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 3 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=80 Driver=(none)
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

---
 drivers/usb/serial/option.c |    6 ++++++
 1 file changed, 6 insertions(+)

@@ -1376,6 +1376,12 @@ static const struct usb_device_id option
 	  .driver_info = NCTRL(2) | RSVD(3) },
 	{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1083, 0xff),	/* Telit FE990 (ECM) */
 	  .driver_info = NCTRL(0) | RSVD(1) },
+	{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x10a0, 0xff),	/* Telit FN20C04 (rmnet) */
+	  .driver_info = RSVD(0) | NCTRL(3) },
+	{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x10a4, 0xff),	/* Telit FN20C04 (rmnet) */
+	  .driver_info = RSVD(0) | NCTRL(3) },
+	{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x10a9, 0xff),	/* Telit FN20C04 (rmnet) */
+	  .driver_info = RSVD(0) | NCTRL(2) | RSVD(3) | RSVD(4) },
 	{ USB_DEVICE(TELIT_VENDOR_ID, TELIT_PRODUCT_ME910),
 	  .driver_info = NCTRL(0) | RSVD(1) | RSVD(3) },
 	{ USB_DEVICE(TELIT_VENDOR_ID, TELIT_PRODUCT_ME910_DUAL_MODEM),

6.1-stable review patch. If anyone has any objections, please let me know.

------------------

From: Greg Kroah-Hartman <[email protected]>

commit 1607830dadeefc407e4956336d9fcd9e9defd810 upstream.

This reverts commit 339f83612f3a569b194680768b22bf113c26a29d.

It has been found to cause problems in a number of Chromebook devices, so revert the change until it can be brought back in a safe way.

---
 drivers/usb/class/cdc-wdm.c |    6 +-----
 1 file changed, 1 insertion(+), 5 deletions(-)

@@ -485,7 +485,6 @@ out_free_mem:
 static int service_outstanding_interrupt(struct wdm_device *desc)
 {
 	int rv = 0;
-	int used;
 
 	/* submit read urb only if the device is waiting for it */
 	if (!desc->resp_count || !--desc->resp_count)

@@ -500,10 +499,7 @@ static int service_outstanding_interrupt
 		goto out;
 	}
 
-	used = test_and_set_bit(WDM_RESPONDING, &desc->flags);
-	if (used)
-		goto out;
-
+	set_bit(WDM_RESPONDING, &desc->flags);
 	spin_unlock_irq(&desc->iuspin);
 	rv = usb_submit_urb(desc->response, GFP_KERNEL);
 	spin_lock_irq(&desc->iuspin);

6.1-stable review patch. If anyone has any objections, please let me know.

------------------

From: Minas Harutyunyan <[email protected]>

commit eed04fa96c48790c1cce73c8a248e9d460b088f8 upstream.

Fixed variable dereference issue in DDMA completion flow.

---
 drivers/usb/dwc2/hcd_ddma.c |    4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

@@ -867,13 +867,15 @@ static int dwc2_cmpl_host_isoc_dma_desc(
 	struct dwc2_dma_desc *dma_desc;
 	struct dwc2_hcd_iso_packet_desc *frame_desc;
 	u16 frame_desc_idx;
-	struct urb *usb_urb = qtd->urb->priv;
+	struct urb *usb_urb;
 	u16 remain = 0;
 	int rc = 0;
 
 	if (!qtd->urb)
 		return -EINVAL;
 
+	usb_urb = qtd->urb->priv;
+
 	dma_sync_single_for_cpu(hsotg->dev, qh->desc_list_dma + (idx *
 				sizeof(struct dwc2_dma_desc)),
 				sizeof(struct dwc2_dma_desc),

6.1-stable review patch. If anyone has any objections, please let me know.

------------------

From: Kai-Heng Feng <[email protected]>

commit d920a2ed8620be04a3301e1a9c2b7cc1de65f19d upstream.

SanDisks USB3 storage may disapper after system reboot:

usb usb2-port3: link state change
xhci_hcd 0000:00:14.0: clear port3 link state change, portsc: 0x2c0 usb usb2-port3: do warm reset, port only
xhci_hcd 0000:00:14.0: xhci_hub_status_data: stopping usb2 port polling xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2b0, return 0x2b0 usb usb2-port3: not warm reset yet, waiting 50ms
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2f0, return 0x2f0 usb usb2-port3: not warm reset yet, waiting 200ms
...
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x6802c0, return 0x7002c0 usb usb2-port3: not warm reset yet, waiting 200ms
xhci_hcd 0000:00:14.0: clear port3 reset change, portsc: 0x4802c0 xhci_hcd 0000:00:14.0: clear port3 warm(BH) reset change, portsc: 0x4002c0 xhci_hcd 0000:00:14.0: clear port3 link state change, portsc: 0x2c0 xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2c0, return 0x2c0 usb usb2-port3: not enabled, trying warm reset again...

This is due to the USB device still cause port change event after xHCI is shuted down:

xhci_hcd 0000:38:00.0: // Setting command ring address to 0xffffe001 xhci_hcd 0000:38:00.0: xhci_resume: starting usb3 port polling. xhci_hcd 0000:38:00.0: xhci_hub_status_data: stopping usb4 port polling xhci_hcd 0000:38:00.0: xhci_hub_status_data: stopping usb3 port polling xhci_hcd 0000:38:00.0: hcd_pci_runtime_resume: 0
xhci_hcd 0000:38:00.0: xhci_shutdown: stopping usb3 port polling. xhci_hcd 0000:38:00.0: // Halt the HC
xhci_hcd 0000:38:00.0: xhci_shutdown completed - status = 1 xhci_hcd 0000:00:14.0: xhci_shutdown: stopping usb1 port polling. xhci_hcd 0000:00:14.0: // Halt the HC
xhci_hcd 0000:00:14.0: xhci_shutdown completed - status = 1 xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x1203, return 0x203 xhci_hcd 0000:00:14.0: set port reset, actual port 2-3 status = 0x1311 xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x201203, return 0x100203 xhci_hcd 0000:00:14.0: clear port3 reset change, portsc: 0x1203 xhci_hcd 0000:00:14.0: clear port3 warm(BH) reset change, portsc: 0x1203 xhci_hcd 0000:00:14.0: clear port3 link state change, portsc: 0x1203 xhci_hcd 0000:00:14.0: clear port3 connect change, portsc: 0x1203 xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x1203, return 0x203 usb 2-3: device not accepting address 2, error -108
xhci_hcd 0000:00:14.0: xHCI dying or halted, can't queue_command xhci_hcd 0000:00:14.0: Set port 2-3 link state, portsc: 0x1203, write 0x11261 xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x1263, return 0x263 xhci_hcd 0000:00:14.0: set port reset, actual port 2-3 status = 0x1271 xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x12b1, return 0x2b1 usb usb2-port3: not reset yet, waiting 60ms
ACPI: PM: Preparing to enter system sleep state S5
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x12f1, return 0x2f1 usb usb2-port3: not reset yet, waiting 200ms
reboot: Restarting system

The port change event is caused by LPM transition, so disabling LPM at shutdown to make sure the device is in U0 for warmboot.

---
 drivers/usb/core/port.c |    4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

@@ -409,8 +409,10 @@ static void usb_port_shutdown(struct dev
 {
 	struct usb_port *port_dev = to_usb_port(dev);
 
-	if (port_dev->child)
+	if (port_dev->child) {
 		usb_disable_usb2_hardware_lpm(port_dev->child);
+		usb_unlocked_disable_lpm(port_dev->child);
+	}
 }
 
 static const struct dev_pm_ops usb_port_pm_ops = {

6.1-stable review patch. If anyone has any objections, please let me know.

------------------

From: Norihiko Hama <[email protected]>

commit 6334b8e4553cc69f51e383c9de545082213d785e upstream.

When ncm function is working and then stop usb0 interface for link down, eth_stop() is called. At this piont, accidentally if usb transport error should happen in usb_ep_enable(), 'in_ep' and/or 'out_ep' may not be enabled.

After that, ncm_disable() is called to disable for ncm unbind but gether_disconnect() is never called since 'in_ep' is not enabled.

As the result, ncm object is released in ncm unbind but 'dev->port_usb' associated to 'ncm->port' is not NULL.

And when ncm bind again to recover netdev, ncm object is reallocated but usb0 interface is already associated to previous released ncm object.

Therefore, once usb0 interface is up and eth_start_xmit() is called, released ncm object is dereferrenced and it might cause use-after-free memory.

[function unlink via configfs]
usb0: eth_stop dev->port_usb=ffffff9b179c3200
--> error happens in usb_ep_enable().
NCM: ncm_disable: ncm=ffffff9b179c3200
--> no gether_disconnect() since ncm->port.in_ep->enabled is false.
NCM: ncm_unbind: ncm unbind ncm=ffffff9b179c3200
NCM: ncm_free: ncm free ncm=ffffff9b179c3200 <-- released ncm

[function link via configfs]
NCM: ncm_alloc: ncm alloc ncm=ffffff9ac4f8a000
NCM: ncm_bind: ncm bind ncm=ffffff9ac4f8a000
NCM: ncm_set_alt: ncm=ffffff9ac4f8a000 alt=0
usb0: eth_open dev->port_usb=ffffff9b179c3200 <-- previous released ncm
usb0: eth_start dev->port_usb=ffffff9b179c3200 <-- eth_start_xmit()
--> dev->wrap()

  Unable to handle kernel paging request at virtual address dead00000000014f

This patch addresses the issue by checking if 'ncm->netdev' is not NULL at ncm_disable() to call gether_disconnect() to deassociate 'dev->port_usb'. It's more reasonable to check 'ncm->netdev' to call gether_connect/disconnect rather than check 'ncm->port.in_ep->enabled' since it might not be enabled but the gether connection might be established.

---
 drivers/usb/gadget/function/f_ncm.c |    4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

@@ -884,7 +884,7 @@ static int ncm_set_alt(struct usb_functi
 		if (alt > 1)
 			goto fail;
 
-		if (ncm->port.in_ep->enabled) {
+		if (ncm->netdev) {
 			DBG(cdev, "reset ncm\n");
 			ncm->netdev = NULL;
 			gether_disconnect(&ncm->port);

@@ -1369,7 +1369,7 @@ static void ncm_disable(struct usb_funct
 
 	DBG(cdev, "ncm deactivated\n");
 
-	if (ncm->port.in_ep->enabled) {
+	if (ncm->netdev) {
 		ncm->netdev = NULL;
 		gether_disconnect(&ncm->port);
 	}

6.1-stable review patch. If anyone has any objections, please let me know.

------------------

From: Alexander Usyskin <[email protected]>

commit 0dc04112bee6fdd6eb847ccb32214703022c0269 upstream.

Extend the quirk to disable MEI interface on Intel PCH Ignition (IGN) and SPS firmwares for RPL-S devices. These firmwares do not support the MEI protocol.

---
 drivers/misc/mei/pci-me.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

@@ -116,7 +116,7 @@ static const struct pci_device_id mei_me
 	{MEI_PCI_DEVICE(MEI_DEV_ID_ADP_P, MEI_ME_PCH15_CFG)},
 	{MEI_PCI_DEVICE(MEI_DEV_ID_ADP_N, MEI_ME_PCH15_CFG)},
 
-	{MEI_PCI_DEVICE(MEI_DEV_ID_RPL_S, MEI_ME_PCH15_CFG)},
+	{MEI_PCI_DEVICE(MEI_DEV_ID_RPL_S, MEI_ME_PCH15_SPS_CFG)},
 
 	{MEI_PCI_DEVICE(MEI_DEV_ID_MTL_M, MEI_ME_PCH15_CFG)},
 	{MEI_PCI_DEVICE(MEI_DEV_ID_ARL_S, MEI_ME_PCH15_CFG)},

6.1-stable review patch. If anyone has any objections, please let me know.

------------------

From: Samuel Thibault <[email protected]>

commit c8d2f34ea96ea3bce6ba2535f867f0d4ee3b22e1 upstream.

In case a console is set up really large and contains a really long word (> 256 characters), we have to stop before the length of the word buffer.

---
 drivers/accessibility/speakup/main.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

@@ -573,7 +573,7 @@ static u_long get_word(struct vc_data *v
 	}
 	attr_ch = get_char(vc, (u_short *)tmp_pos, &spk_attr);
 	buf[cnt++] = attr_ch;
-	while (tmpx < vc->vc_cols - 1) {
+	while (tmpx < vc->vc_cols - 1 && cnt < sizeof(buf) - 1) {
 		tmp_pos += 2;
 		tmpx++;
 		ch = get_char(vc, (u_short *)tmp_pos, &temp);

6.1-stable review patch. If anyone has any objections, please let me know.

------------------

From: Alan Stern <[email protected]>

commit a90bca2228c0646fc29a72689d308e5fe03e6d78 upstream.

The sysfs_break_active_protection() routine has an obvious reference leak in its error path. If the call to kernfs_find_and_get() fails then kn will be NULL, so the companion sysfs_unbreak_active_protection() routine won't get called (and would only cause an access violation by trying to dereference kn->parent if it was called). As a result, the reference to kobj acquired at the start of the function will never be released.

Fix the leak by adding an explicit kobject_put() call when kn is NULL.

---
 fs/sysfs/file.c |    2 ++
 1 file changed, 2 insertions(+)

@@ -450,6 +450,8 @@ struct kernfs_node *sysfs_break_active_p
 	kn = kernfs_find_and_get(kobj->sd, attr->name);
 	if (kn)
 		kernfs_break_active_protection(kn);
+	else
+		kobject_put(kobj);
 	return kn;
 }
 EXPORT_SYMBOL_GPL(sysfs_break_active_protection);

6.1-stable review patch. If anyone has any objections, please let me know.

------------------

From: Sean Christopherson <[email protected]>

commit fd706c9b1674e2858766bfbf7430534c2b26fbef upstream.

Add kvm_vcpu_arch.is_amd_compatible to cache if a vCPU's vendor model is compatible with AMD, i.e. if the vCPU vendor is AMD or Hygon, along with helpers to check if a vCPU is compatible AMD vs. Intel. To handle Intel vs. AMD behavior related to masking the LVTPC entry, KVM will need to check for vendor compatibility on every PMI injection, i.e. querying for AMD will soon be a moderately hot path.

Note! This subtly (or maybe not-so-subtly) makes "Intel compatible" KVM's default behavior, both if userspace omits (or never sets) CPUID 0x0 and if userspace sets a completely unknown vendor. One could argue that KVM should treat such vCPUs as not being compatible with Intel *or* AMD, but that would add useless complexity to KVM.

KVM needs to do *something* in the face of vendor specific behavior, and so unless KVM conjured up a magic third option, choosing to treat unknown vendors as neither Intel nor AMD means that checks on AMD compatibility would yield Intel behavior, and checks for Intel compatibility would yield AMD behavior. And that's far worse as it would effectively yield random behavior depending on whether KVM checked for AMD vs. Intel vs. !AMD vs. !Intel. And practically speaking, all x86 CPUs follow either Intel or AMD architecture, i.e. "supporting" an unknown third architecture adds no value.

Deliberately don't convert any of the existing guest_cpuid_is_intel() checks, as the Intel side of things is messier due to some flows explicitly checking for exactly vendor==Intel, versus some flows assuming anything that isn't "AMD compatible" gets Intel behavior. The Intel code will be cleaned up in the future.

Message-ID: <[email protected]>

---
 arch/x86/include/asm/kvm_host.h |    1 +
 arch/x86/kvm/cpuid.c            |    1 +
 arch/x86/kvm/cpuid.h            |   10 ++++++++++
 arch/x86/kvm/mmu/mmu.c          |    2 +-
 arch/x86/kvm/x86.c              |    2 +-
 5 files changed, 14 insertions(+), 2 deletions(-)

@@ -773,6 +773,7 @@ struct kvm_vcpu_arch {
 	int cpuid_nent;
 	struct kvm_cpuid_entry2 *cpuid_entries;
 	u32 kvm_cpuid_base;
+	bool is_amd_compatible;
 
 	u64 reserved_gpa_bits;
 	int maxphyaddr;

@@ -340,6 +340,7 @@ static void kvm_vcpu_after_set_cpuid(str
 
 	kvm_update_pv_runtime(vcpu);
 
+	vcpu->arch.is_amd_compatible = guest_cpuid_is_amd_or_hygon(vcpu);
 	vcpu->arch.maxphyaddr = cpuid_query_maxphyaddr(vcpu);
 	vcpu->arch.reserved_gpa_bits = kvm_vcpu_reserved_gpa_bits_raw(vcpu);
 

@@ -125,6 +125,16 @@ static inline bool guest_cpuid_is_intel(
 	return best && is_guest_vendor_intel(best->ebx, best->ecx, best->edx);
 }
 
+static inline bool guest_cpuid_is_amd_compatible(struct kvm_vcpu *vcpu)
+{
+	return vcpu->arch.is_amd_compatible;
+}
+
+static inline bool guest_cpuid_is_intel_compatible(struct kvm_vcpu *vcpu)
+{
+	return !guest_cpuid_is_amd_compatible(vcpu);
+}
+
 static inline int guest_cpuid_family(struct kvm_vcpu *vcpu)
 {
 	struct kvm_cpuid_entry2 *best;

@@ -4649,7 +4649,7 @@ static void reset_guest_rsvds_bits_mask(
 				context->cpu_role.base.level, is_efer_nx(context),
 				guest_can_use_gbpages(vcpu),
 				is_cr4_pse(context),
-				guest_cpuid_is_amd_or_hygon(vcpu));
+				guest_cpuid_is_amd_compatible(vcpu));
 }
 
 static void

@@ -3278,7 +3278,7 @@ static bool is_mci_status_msr(u32 msr)
 static bool can_set_mci_status(struct kvm_vcpu *vcpu)
 {
 	/* McStatusWrEn enabled? */
-	if (guest_cpuid_is_amd_or_hygon(vcpu))
+	if (guest_cpuid_is_amd_compatible(vcpu))
 		return !!(vcpu->arch.msr_hwcr & BIT_ULL(18));
 
 	return false;

6.1-stable review patch. If anyone has any objections, please let me know.

------------------

From: Sean Christopherson <[email protected]>

commit 9e985cbf2942a1bb8fcef9adc2a17d90fd7ca8ee upstream.

Drop support for virtualizing adaptive PEBS, as KVM's implementation is architecturally broken without an obvious/easy path forward, and because exposing adaptive PEBS can leak host LBRs to the guest, i.e. can leak host kernel addresses to the guest.

Bug #1 is that KVM doesn't account for the upper 32 bits of IA32_FIXED_CTR_CTRL when (re)programming fixed counters, e.g fixed_ctrl_field() drops the upper bits, reprogram_fixed_counters() stores local variables as u8s and truncates the upper bits too, etc.

Bug #2 is that, because KVM _always_ sets precise_ip to a non-zero value for PEBS events, perf will _always_ generate an adaptive record, even if the guest requested a basic record. Note, KVM will also enable adaptive PEBS in individual *counter*, even if adaptive PEBS isn't exposed to the guest, but this is benign as MSR_PEBS_DATA_CFG is guaranteed to be zero, i.e. the guest will only ever see Basic records.

Bug #3 is in perf. intel_pmu_disable_fixed() doesn't clear the upper bits either, i.e. leaves ICL_FIXED_0_ADAPTIVE set, and intel_pmu_enable_fixed() effectively doesn't clear ICL_FIXED_0_ADAPTIVE either. I.e. perf _always_ enables ADAPTIVE counters, regardless of what KVM requests.

Bug #4 is that adaptive PEBS *might* effectively bypass event filters set by the host, as "Updated Memory Access Info Group" records information that might be disallowed by userspace via KVM_SET_PMU_EVENT_FILTER.

Bug #5 is that KVM doesn't ensure LBR MSRs hold guest values (or at least zeros) when entering a vCPU with adaptive PEBS, which allows the guest to read host LBRs, i.e. host RIPs/addresses, by enabling "LBR Entries" records.

Disable adaptive PEBS support as an immediate fix due to the severity of the LBR leak in particular, and because fixing all of the bugs will be non-trivial, e.g. not suitable for backporting to stable kernels.

Note! This will break live migration, but trying to make KVM play nice with live migration would be quite complicated, wouldn't be guaranteed to work (i.e. KVM might still kill/confuse the guest), and it's not clear that there are any publicly available VMMs that support adaptive PEBS, let alone live migrate VMs that support adaptive PEBS, e.g. QEMU doesn't support PEBS in any capacity.

---
 arch/x86/kvm/vmx/vmx.c |   24 ++++++++++++++++++++++--
 1 file changed, 22 insertions(+), 2 deletions(-)

@@ -7742,8 +7742,28 @@ static u64 vmx_get_perf_capabilities(voi
 
 	if (vmx_pebs_supported()) {
 		perf_cap |= host_perf_cap & PERF_CAP_PEBS_MASK;
-		if ((perf_cap & PERF_CAP_PEBS_FORMAT) < 4)
-			perf_cap &= ~PERF_CAP_PEBS_BASELINE;
+
+		/*
+		 * Disallow adaptive PEBS as it is functionally broken, can be
+		 * used by the guest to read *host* LBRs, and can be used to
+		 * bypass userspace event filters.  To correctly and safely
+		 * support adaptive PEBS, KVM needs to:
+		 *
+		 * 1. Account for the ADAPTIVE flag when (re)programming fixed
+		 *    counters.
+		 *
+		 * 2. Gain support from perf (or take direct control of counter
+		 *    programming) to support events without adaptive PEBS
+		 *    enabled for the hardware counter.
+		 *
+		 * 3. Ensure LBR MSRs cannot hold host data on VM-Entry with
+		 *    adaptive PEBS enabled and MSR_PEBS_DATA_CFG.LBRS=1.
+		 *
+		 * 4. Document which PMU events are effectively exposed to the
+		 *    guest via adaptive PEBS, and make adaptive PEBS mutually
+		 *    exclusive with KVM_SET_PMU_EVENT_FILTER if necessary.
+		 */
+		perf_cap &= ~PERF_CAP_PEBS_BASELINE;
 	}
 
 	return perf_cap;

6.1-stable review patch. If anyone has any objections, please let me know.

------------------

From: Sandipan Das <[email protected]>

commit 49ff3b4aec51e3abfc9369997cc603319b02af9a upstream.

On AMD and Hygon platforms, the local APIC does not automatically set the mask bit of the LVTPC register when handling a PMI and there is no need to clear it in the kernel's PMI handler.

For guests, the mask bit is currently set by kvm_apic_local_deliver() and unless it is cleared by the guest kernel's PMI handler, PMIs stop arriving and break use-cases like sampling with perf record.

This does not affect non-PerfMonV2 guests because PMIs are handled in the guest kernel by x86_pmu_handle_irq() which always clears the LVTPC mask bit irrespective of the vendor.

Before:

  $ perf record -e cycles:u true
  [ perf record: Woken up 1 times to write data ]
  [ perf record: Captured and wrote 0.001 MB perf.data (1 samples) ]

After:

  $ perf record -e cycles:u true
  [ perf record: Woken up 1 times to write data ]
  [ perf record: Captured and wrote 0.002 MB perf.data (19 samples) ]

Message-ID: <[email protected]>

---
 arch/x86/kvm/lapic.c |    3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

@@ -2548,7 +2548,8 @@ int kvm_apic_local_deliver(struct kvm_la
 		trig_mode = reg & APIC_LVT_LEVEL_TRIGGER;
 
 		r = __apic_accept_irq(apic, mode, vector, 1, trig_mode, NULL);
-		if (r && lvt_type == APIC_LVTPC)
+		if (r && lvt_type == APIC_LVTPC &&
+		    guest_cpuid_is_intel_compatible(apic->vcpu))
 			kvm_lapic_set_reg(apic, APIC_LVTPC, reg | APIC_LVT_MASKED);
 		return r;
 	}

6.1-stable review patch. If anyone has any objections, please let me know.

------------------

From: Yaxiong Tian <[email protected]>

commit 50449ca66cc5a8cbc64749cf4b9f3d3fc5f4b457 upstream.

On arm64 machines, swsusp_save() faults if it attempts to access MEMBLOCK_NOMAP memory ranges. This can be reproduced in QEMU using UEFI when booting with rodata=off debug_pagealloc=off and CONFIG_KFENCE=n:

  Unable to handle kernel paging request at virtual address ffffff8000000000
  Mem abort info:
    ESR = 0x0000000096000007
    EC = 0x25: DABT (current EL), IL = 32 bits
    SET = 0, FnV = 0
    EA = 0, S1PTW = 0
    FSC = 0x07: level 3 translation fault
  Data abort info:
    ISV = 0, ISS = 0x00000007, ISS2 = 0x00000000
    CM = 0, WnR = 0, TnD = 0, TagAccess = 0
    GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0
  swapper pgtable: 4k pages, 39-bit VAs, pgdp=00000000eeb0b000
  [ffffff8000000000] pgd=180000217fff9803, p4d=180000217fff9803, pud=180000217fff9803, pmd=180000217fff8803, pte=0000000000000000
  Internal error: Oops: 0000000096000007 [#1] SMP
  Internal error: Oops: 0000000096000007 [#1] SMP
  Modules linked in: xt_multiport ipt_REJECT nf_reject_ipv4 xt_conntrack nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 libcrc32c iptable_filter bpfilter rfkill at803x snd_hda_codec_hdmi snd_hda_intel snd_intel_dspcfg dwmac_generic stmmac_platform snd_hda_codec stmmac joydev pcs_xpcs snd_hda_core phylink ppdev lp parport ramoops reed_solomon ip_tables x_tables nls_iso8859_1 vfat multipath linear amdgpu amdxcp drm_exec gpu_sched drm_buddy hid_generic usbhid hid radeon video drm_suballoc_helper drm_ttm_helper ttm i2c_algo_bit drm_display_helper cec drm_kms_helper drm
  CPU: 0 PID: 3663 Comm: systemd-sleep Not tainted 6.6.2+ #76
  Source Version: 4e22ed63a0a48e7a7cff9b98b7806d8d4add7dc0
  Hardware name: Greatwall GW-XXXXXX-XXX/GW-XXXXXX-XXX, BIOS KunLun BIOS V4.0 01/19/2021
  pstate: 600003c5 (nZCv DAIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
  pc : swsusp_save+0x280/0x538
  lr : swsusp_save+0x280/0x538
  sp : ffffffa034a3fa40
  x29: ffffffa034a3fa40 x28: ffffff8000001000 x27: 0000000000000000
  x26: ffffff8001400000 x25: ffffffc08113e248 x24: 0000000000000000
  x23: 0000000000080000 x22: ffffffc08113e280 x21: 00000000000c69f2
  x20: ffffff8000000000 x19: ffffffc081ae2500 x18: 0000000000000000
  x17: 6666662074736420 x16: 3030303030303030 x15: 3038666666666666
  x14: 0000000000000b69 x13: ffffff9f89088530 x12: 00000000ffffffea
  x11: 00000000ffff7fff x10: 00000000ffff7fff x9 : ffffffc08193f0d0
  x8 : 00000000000bffe8 x7 : c0000000ffff7fff x6 : 0000000000000001
  x5 : ffffffa0fff09dc8 x4 : 0000000000000000 x3 : 0000000000000027
  x2 : 0000000000000000 x1 : 0000000000000000 x0 : 000000000000004e
  Call trace:
   swsusp_save+0x280/0x538
   swsusp_arch_suspend+0x148/0x190
   hibernation_snapshot+0x240/0x39c
   hibernate+0xc4/0x378
   state_store+0xf0/0x10c
   kobj_attr_store+0x14/0x24

The reason is swsusp_save() -> copy_data_pages() -> page_is_saveable() -> kernel_page_present() assuming that a page is always present when can_set_direct_map() is false (all of rodata_full, debug_pagealloc_enabled() and arm64_kfence_can_set_direct_map() false), irrespective of the MEMBLOCK_NOMAP ranges. Such MEMBLOCK_NOMAP regions should not be saved during hibernation.

This problem was introduced by changes to the pfn_valid() logic in commit a7d9f306ba70 ("arm64: drop pfn_valid_within() and simplify pfn_valid()").

Similar to other architectures, drop the !can_set_direct_map() check in kernel_page_present() so that page_is_savable() skips such pages.

---
 arch/arm64/mm/pageattr.c |    3 ---
 1 file changed, 3 deletions(-)

@@ -220,9 +220,6 @@ bool kernel_page_present(struct page *pa
 	pte_t *ptep;
 	unsigned long addr = (unsigned long)page_address(page);
 
-	if (!can_set_direct_map())
-		return true;
-
 	pgdp = pgd_offset_k(addr);
 	if (pgd_none(READ_ONCE(*pgdp)))
 		return false;

6.1-stable review patch. If anyone has any objections, please let me know.

------------------

From: Yuntao Wang <[email protected]>

commit 46dad3c1e57897ab9228332f03e1c14798d2d3b9 upstream.

We allocate memory of size 'xlen + strlen(boot_command_line) + 1' for static_command_line, but the strings copied into static_command_line are extra_command_line and command_line, rather than extra_command_line and boot_command_line.

When strlen(command_line) > strlen(boot_command_line), static_command_line will overflow.

This patch just recovers strlen(command_line) which was miss-consolidated with strlen(boot_command_line) in the commit f5c7310ac73e ("init/main: add checks for the return value of memblock_alloc*()")

---
 init/main.c |    2 ++
 1 file changed, 2 insertions(+)

@@ -633,6 +633,8 @@ static void __init setup_command_line(ch
 	if (!saved_command_line)
 		panic("%s: Failed to allocate %zu bytes\n", __func__, len + ilen);
 
+	len = xlen + strlen(command_line) + 1;
+
 	static_command_line = memblock_alloc(len, SMP_CACHE_BYTES);
 	if (!static_command_line)
 		panic("%s: Failed to allocate %zu bytes\n", __func__, len);

6.1-stable review patch. If anyone has any objections, please let me know.

------------------

From: Miaohe Lin <[email protected]>

commit 1983184c22dd84a4d95a71e5c6775c2638557dc7 upstream.

When I did hard offline test with hugetlb pages, below deadlock occurs:

======================================================
WARNING: possible circular locking dependency detected 6.8.0-11409-gf6cef5f8c37f #1 Not tainted
------------------------------------------------------
bash/46904 is trying to acquire lock:
ffffffffabe68910 (cpu_hotplug_lock){++++}-{0:0}, at: static_key_slow_dec+0x16/0x60

but task is already holding lock:
ffffffffabf92ea8 (pcp_batch_high_lock){+.+.}-{3:3}, at: zone_pcp_disable+0x16/0x40

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #1 (pcp_batch_high_lock){+.+.}-{3:3}:

       __mutex_lock+0x6c/0x770
       page_alloc_cpu_online+0x3c/0x70
       cpuhp_invoke_callback+0x397/0x5f0
       __cpuhp_invoke_callback_range+0x71/0xe0
       _cpu_up+0xeb/0x210
       cpu_up+0x91/0xe0
       cpuhp_bringup_mask+0x49/0xb0
       bringup_nonboot_cpus+0xb7/0xe0
       smp_init+0x25/0xa0
       kernel_init_freeable+0x15f/0x3e0
       kernel_init+0x15/0x1b0
       ret_from_fork+0x2f/0x50
       ret_from_fork_asm+0x1a/0x30

-> #0 (cpu_hotplug_lock){++++}-{0:0}:

       __lock_acquire+0x1298/0x1cd0
       lock_acquire+0xc0/0x2b0
       cpus_read_lock+0x2a/0xc0
       static_key_slow_dec+0x16/0x60
       __hugetlb_vmemmap_restore_folio+0x1b9/0x200
       dissolve_free_huge_page+0x211/0x260
       __page_handle_poison+0x45/0xc0
       memory_failure+0x65e/0xc70
       hard_offline_page_store+0x55/0xa0
       kernfs_fop_write_iter+0x12c/0x1d0
       vfs_write+0x387/0x550
       ksys_write+0x64/0xe0
       do_syscall_64+0xca/0x1e0
       entry_SYSCALL_64_after_hwframe+0x6d/0x75

other info that might help us debug this:

 Possible unsafe locking scenario:

       CPU0                    CPU1
       ----                    ----
  lock(pcp_batch_high_lock);
                               lock(cpu_hotplug_lock);
                               lock(pcp_batch_high_lock);

rlock(cpu_hotplug_lock);

*** DEADLOCK ***

5 locks held by bash/46904:
#0: ffff98f6c3bb23f0 (sb_writers#5){.+.+}-{0:0}, at: ksys_write+0x64/0xe0 #1: ffff98f6c328e488 (&of->mutex){+.+.}-{3:3}, at: kernfs_fop_write_iter+0xf8/0x1d0 #2: ffff98ef83b31890 (kn->active#113){.+.+}-{0:0}, at: kernfs_fop_write_iter+0x100/0x1d0 #3: ffffffffabf9db48 (mf_mutex){+.+.}-{3:3}, at: memory_failure+0x44/0xc70 #4: ffffffffabf92ea8 (pcp_batch_high_lock){+.+.}-{3:3}, at: zone_pcp_disable+0x16/0x40

stack backtrace:
CPU: 10 PID: 46904 Comm: bash Kdump: loaded Not tainted 6.8.0-11409-gf6cef5f8c37f #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014
Call Trace:
 <TASK>
 dump_stack_lvl+0x68/0xa0
 check_noncircular+0x129/0x140
 __lock_acquire+0x1298/0x1cd0
 lock_acquire+0xc0/0x2b0
 cpus_read_lock+0x2a/0xc0
 static_key_slow_dec+0x16/0x60
 __hugetlb_vmemmap_restore_folio+0x1b9/0x200
 dissolve_free_huge_page+0x211/0x260
 __page_handle_poison+0x45/0xc0
 memory_failure+0x65e/0xc70
 hard_offline_page_store+0x55/0xa0
 kernfs_fop_write_iter+0x12c/0x1d0
 vfs_write+0x387/0x550
 ksys_write+0x64/0xe0
 do_syscall_64+0xca/0x1e0
 entry_SYSCALL_64_after_hwframe+0x6d/0x75
RIP: 0033:0x7fc862314887
Code: 10 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb b7 0f 1f 00 f3 0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 b8 01 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 51 c3 48 83 ec 28 48 89 54 24 18 48 89 74 24
RSP: 002b:00007fff19311268 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 000000000000000c RCX: 00007fc862314887
RDX: 000000000000000c RSI: 000056405645fe10 RDI: 0000000000000001
RBP: 000056405645fe10 R08: 00007fc8623d1460 R09: 000000007fffffff
R10: 0000000000000000 R11: 0000000000000246 R12: 000000000000000c
R13: 00007fc86241b780 R14: 00007fc862417600 R15: 00007fc862416a00

In short, below scene breaks the lock dependency chain:

memory_failure
__page_handle_poison
zone_pcp_disable -- lock(pcp_batch_high_lock)
dissolve_free_huge_page
__hugetlb_vmemmap_restore_folio
static_key_slow_dec
cpus_read_lock -- rlock(cpu_hotplug_lock)

Fix this by calling drain_all_pages() instead.

This issue won't occur until commit a6b40850c442 ("mm: hugetlb: replace hugetlb_free_vmemmap_enabled with a static_key"). As it introduced rlock(cpu_hotplug_lock) in dissolve_free_huge_page() code path while lock(pcp_batch_high_lock) is already in the __page_handle_poison().

---
 mm/memory-failure.c |   18 +++++++++++++++---
 1 file changed, 15 insertions(+), 3 deletions(-)

@@ -84,11 +84,23 @@ static int __page_handle_poison(struct p
 {
 	int ret;
 
-	zone_pcp_disable(page_zone(page));
+	/*
+	 * zone_pcp_disable() can't be used here. It will
+	 * hold pcp_batch_high_lock and dissolve_free_huge_page() might hold
+	 * cpu_hotplug_lock via static_key_slow_dec() when hugetlb vmemmap
+	 * optimization is enabled. This will break current lock dependency
+	 * chain and leads to deadlock.
+	 * Disabling pcp before dissolving the page was a deterministic
+	 * approach because we made sure that those pages cannot end up in any
+	 * PCP list. Draining PCP lists expels those pages to the buddy system,
+	 * but nothing guarantees that those pages do not get back to a PCP
+	 * queue if we need to refill those.
+	 */
 	ret = dissolve_free_huge_page(page);
-	if (!ret)
+	if (!ret) {
+		drain_all_pages(page_zone(page));
 		ret = take_page_off_buddy(page);
-	zone_pcp_enable(page_zone(page));
+	}
 
 	return ret;
 }

6.1-stable review patch. If anyone has any objections, please let me know.

------------------

From: xinhui pan <[email protected]>

commit 6fef2d4c00b5b8561ad68dd2b68173f5c6af1e75 upstream.

Verify the parameters of amdgpu_vm_bo_(map/replace_map/clearing_mappings) in one common place.

---
 drivers/gpu/drm/amd/amdgpu/amdgpu_vm.c |   72 +++++++++++++++++++++------------
 1 file changed, 46 insertions(+), 26 deletions(-)

@@ -1400,6 +1400,37 @@ static void amdgpu_vm_bo_insert_map(stru
 	trace_amdgpu_vm_bo_map(bo_va, mapping);
 }
 
+/* Validate operation parameters to prevent potential abuse */
+static int amdgpu_vm_verify_parameters(struct amdgpu_device *adev,
+					  struct amdgpu_bo *bo,
+					  uint64_t saddr,
+					  uint64_t offset,
+					  uint64_t size)
+{
+	uint64_t tmp, lpfn;
+
+	if (saddr & AMDGPU_GPU_PAGE_MASK
+	    || offset & AMDGPU_GPU_PAGE_MASK
+	    || size & AMDGPU_GPU_PAGE_MASK)
+		return -EINVAL;
+
+	if (check_add_overflow(saddr, size, &tmp)
+	    || check_add_overflow(offset, size, &tmp)
+	    || size == 0 /* which also leads to end < begin */)
+		return -EINVAL;
+
+	/* make sure object fit at this offset */
+	if (bo && offset + size > amdgpu_bo_size(bo))
+		return -EINVAL;
+
+	/* Ensure last pfn not exceed max_pfn */
+	lpfn = (saddr + size - 1) >> AMDGPU_GPU_PAGE_SHIFT;
+	if (lpfn >= adev->vm_manager.max_pfn)
+		return -EINVAL;
+
+	return 0;
+}
+
 /**
  * amdgpu_vm_bo_map - map bo inside a vm
  *

@@ -1426,21 +1457,14 @@ int amdgpu_vm_bo_map(struct amdgpu_devic
 	struct amdgpu_bo *bo = bo_va->base.bo;
 	struct amdgpu_vm *vm = bo_va->base.vm;
 	uint64_t eaddr;
+	int r;
 
-	/* validate the parameters */
-	if (saddr & ~PAGE_MASK || offset & ~PAGE_MASK || size & ~PAGE_MASK)
-		return -EINVAL;
-	if (saddr + size <= saddr || offset + size <= offset)
-		return -EINVAL;
-
-	/* make sure object fit at this offset */
-	eaddr = saddr + size - 1;
-	if ((bo && offset + size > amdgpu_bo_size(bo)) ||
-	    (eaddr >= adev->vm_manager.max_pfn << AMDGPU_GPU_PAGE_SHIFT))
-		return -EINVAL;
+	r = amdgpu_vm_verify_parameters(adev, bo, saddr, offset, size);
+	if (r)
+		return r;
 
 	saddr /= AMDGPU_GPU_PAGE_SIZE;
-	eaddr /= AMDGPU_GPU_PAGE_SIZE;
+	eaddr = saddr + (size - 1) / AMDGPU_GPU_PAGE_SIZE;
 
 	tmp = amdgpu_vm_it_iter_first(&vm->va, saddr, eaddr);
 	if (tmp) {

@@ -1493,17 +1517,9 @@ int amdgpu_vm_bo_replace_map(struct amdg
 	uint64_t eaddr;
 	int r;
 
-	/* validate the parameters */
-	if (saddr & ~PAGE_MASK || offset & ~PAGE_MASK || size & ~PAGE_MASK)
-		return -EINVAL;
-	if (saddr + size <= saddr || offset + size <= offset)
-		return -EINVAL;
-
-	/* make sure object fit at this offset */
-	eaddr = saddr + size - 1;
-	if ((bo && offset + size > amdgpu_bo_size(bo)) ||
-	    (eaddr >= adev->vm_manager.max_pfn << AMDGPU_GPU_PAGE_SHIFT))
-		return -EINVAL;
+	r = amdgpu_vm_verify_parameters(adev, bo, saddr, offset, size);
+	if (r)
+		return r;
 
 	/* Allocate all the needed memory */
 	mapping = kmalloc(sizeof(*mapping), GFP_KERNEL);

@@ -1517,7 +1533,7 @@ int amdgpu_vm_bo_replace_map(struct amdg
 	}
 
 	saddr /= AMDGPU_GPU_PAGE_SIZE;
-	eaddr /= AMDGPU_GPU_PAGE_SIZE;
+	eaddr = saddr + (size - 1) / AMDGPU_GPU_PAGE_SIZE;
 
 	mapping->start = saddr;
 	mapping->last = eaddr;

@@ -1604,10 +1620,14 @@ int amdgpu_vm_bo_clear_mappings(struct a
 	struct amdgpu_bo_va_mapping *before, *after, *tmp, *next;
 	LIST_HEAD(removed);
 	uint64_t eaddr;
+	int r;
+
+	r = amdgpu_vm_verify_parameters(adev, NULL, saddr, 0, size);
+	if (r)
+		return r;
 
-	eaddr = saddr + size - 1;
 	saddr /= AMDGPU_GPU_PAGE_SIZE;
-	eaddr /= AMDGPU_GPU_PAGE_SIZE;
+	eaddr = saddr + (size - 1) / AMDGPU_GPU_PAGE_SIZE;
 
 	/* Allocate all the needed memory */
 	before = kzalloc(sizeof(*before), GFP_KERNEL);

6.1-stable review patch. If anyone has any objections, please let me know.

------------------

From: Zack Rusin <[email protected]>

commit d4c972bff3129a9dd4c22a3999fd8eba1a81531a upstream.

The table of primary plane formats wasn't sorted at all, leading to applications picking our least desirable formats by defaults.

Sort the primary plane formats according to our order of preference.

Nice side-effect of this change is that it makes IGT's kms_atomic plane-invalid-params pass because the test picks the first format which for vmwgfx was DRM_FORMAT_XRGB1555 and uses fb's with odd sizes which make Pixman, which IGT depends on assert due to the fact that our 16bpp formats aren't 32 bit aligned like Pixman requires all formats to be.

---
 drivers/gpu/drm/vmwgfx/vmwgfx_kms.h |    4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

@@ -246,10 +246,10 @@ struct vmw_framebuffer_bo {
 
 
 static const uint32_t __maybe_unused vmw_primary_plane_formats[] = {
-	DRM_FORMAT_XRGB1555,
-	DRM_FORMAT_RGB565,
 	DRM_FORMAT_XRGB8888,
 	DRM_FORMAT_ARGB8888,
+	DRM_FORMAT_RGB565,
+	DRM_FORMAT_XRGB1555,
 };
 
 static const uint32_t __maybe_unused vmw_cursor_plane_formats[] = {

6.1-stable review patch. If anyone has any objections, please let me know.

------------------

From: Zack Rusin <[email protected]>

commit a60ccade88f926e871a57176e86a34bbf0db0098 upstream.

The conditional was supposed to prevent enabling of a crtc state without a set primary plane. Accidently it also prevented disabling crtc state with a set primary plane. Neither is correct.

Fix the conditional and just driver-warn when a crtc state has been enabled without a primary plane which will help debug broken userspace.

Fixes IGT's kms_atomic_interruptible and kms_atomic_transition tests.

---
 drivers/gpu/drm/vmwgfx/vmwgfx_kms.c |   11 ++++++++---
 1 file changed, 8 insertions(+), 3 deletions(-)

@@ -793,6 +793,7 @@ int vmw_du_cursor_plane_atomic_check(str
 int vmw_du_crtc_atomic_check(struct drm_crtc *crtc,
 			     struct drm_atomic_state *state)
 {
+	struct vmw_private *vmw = vmw_priv(crtc->dev);
 	struct drm_crtc_state *new_state = drm_atomic_get_new_crtc_state(state,
 									 crtc);
 	struct vmw_display_unit *du = vmw_crtc_to_du(new_state->crtc);

@@ -800,9 +801,13 @@ int vmw_du_crtc_atomic_check(struct drm_
 	bool has_primary = new_state->plane_mask &
 			   drm_plane_mask(crtc->primary);
 
-	/* We always want to have an active plane with an active CRTC */
-	if (has_primary != new_state->enable)
-		return -EINVAL;
+	/*
+	 * This is fine in general, but broken userspace might expect
+	 * some actual rendering so give a clue as why it's blank.
+	 */
+	if (new_state->enable && !has_primary)
+		drm_dbg_driver(&vmw->drm,
+			       "CRTC without a primary plane will be blank.\n");
 
 
 	if (new_state->connector_mask != connector_mask &&

6.1-stable review patch. If anyone has any objections, please let me know.

------------------

From: Dave Airlie <[email protected]>

commit fff1386cc889d8fb4089d285f883f8cba62d82ce upstream.

Running a lot of VK CTS in parallel against nouveau, once every few hours you might see something like this crash.

BUG: kernel NULL pointer dereference, address: 0000000000000008
PGD 8000000114e6e067 P4D 8000000114e6e067 PUD 109046067 PMD 0
Oops: 0000 [#1] PREEMPT SMP PTI
CPU: 7 PID: 53891 Comm: deqp-vk Not tainted 6.8.0-rc6+ #27
Hardware name: Gigabyte Technology Co., Ltd. Z390 I AORUS PRO WIFI/Z390 I AORUS PRO WIFI-CF, BIOS F8 11/05/2021
RIP: 0010:gp100_vmm_pgt_mem+0xe3/0x180 [nouveau]
Code: c7 48 01 c8 49 89 45 58 85 d2 0f 84 95 00 00 00 41 0f b7 46 12 49 8b 7e 08 89 da 42 8d 2c f8 48 8b 47 08 41 83 c7 01 48 89 ee <48> 8b 40 08 ff d0 0f 1f 00 49 8b 7e 08 48 89 d9 48 8d 75 04 48 c1
RSP: 0000:ffffac20c5857838 EFLAGS: 00010202
RAX: 0000000000000000 RBX: 00000000004d8001 RCX: 0000000000000001
RDX: 00000000004d8001 RSI: 00000000000006d8 RDI: ffffa07afe332180
RBP: 00000000000006d8 R08: ffffac20c5857ad0 R09: 0000000000ffff10
R10: 0000000000000001 R11: ffffa07af27e2de0 R12: 000000000000001c
R13: ffffac20c5857ad0 R14: ffffa07a96fe9040 R15: 000000000000001c
FS:  00007fe395eed7c0(0000) GS:ffffa07e2c980000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000008 CR3: 000000011febe001 CR4: 00000000003706f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:

...

 ? gp100_vmm_pgt_mem+0xe3/0x180 [nouveau]
 ? gp100_vmm_pgt_mem+0x37/0x180 [nouveau]
 nvkm_vmm_iter+0x351/0xa20 [nouveau]
 ? __pfx_nvkm_vmm_ref_ptes+0x10/0x10 [nouveau]
 ? __pfx_gp100_vmm_pgt_mem+0x10/0x10 [nouveau]
 ? __pfx_gp100_vmm_pgt_mem+0x10/0x10 [nouveau]
 ? __lock_acquire+0x3ed/0x2170
 ? __pfx_gp100_vmm_pgt_mem+0x10/0x10 [nouveau]
 nvkm_vmm_ptes_get_map+0xc2/0x100 [nouveau]
 ? __pfx_nvkm_vmm_ref_ptes+0x10/0x10 [nouveau]
 ? __pfx_gp100_vmm_pgt_mem+0x10/0x10 [nouveau]
 nvkm_vmm_map_locked+0x224/0x3a0 [nouveau]

Adding any sort of useful debug usually makes it go away, so I hand wrote the function in a line, and debugged the asm.

Every so often pt->memory->ptrs is NULL. This ptrs ptr is set in the nv50_instobj_acquire called from nvkm_kmap.

If Thread A and Thread B both get to nv50_instobj_acquire around the same time, and Thread A hits the refcount_set line, and in lockstep thread B succeeds at refcount_inc_not_zero, there is a chance the ptrs value won't have been stored since refcount_set is unordered. Force a memory barrier here, I picked smp_mb, since we want it on all CPUs and it's write followed by a read.

v2: use paired smp_rmb/smp_wmb.

---
 drivers/gpu/drm/nouveau/nvkm/subdev/instmem/nv50.c |    7 ++++++-
 1 file changed, 6 insertions(+), 1 deletion(-)

@@ -221,8 +221,11 @@ nv50_instobj_acquire(struct nvkm_memory
 	void __iomem *map = NULL;
 
 	/* Already mapped? */
-	if (refcount_inc_not_zero(&iobj->maps))
+	if (refcount_inc_not_zero(&iobj->maps)) {
+		/* read barrier match the wmb on refcount set */
+		smp_rmb();
 		return iobj->map;
+	}
 
 	/* Take the lock, and re-check that another thread hasn't
 	 * already mapped the object in the meantime.

@@ -249,6 +252,8 @@ nv50_instobj_acquire(struct nvkm_memory
 			iobj->base.memory.ptrs = &nv50_instobj_fast;
 		else
 			iobj->base.memory.ptrs = &nv50_instobj_slow;
+		/* barrier to ensure the ptrs are written before refcount is set */
+		smp_wmb();
 		refcount_set(&iobj->maps, 1);
 	}
 

6.1-stable review patch. If anyone has any objections, please let me know.

------------------

From: Qiang Zhang <[email protected]>

commit 89f9a1e876b5a7ad884918c03a46831af202c8a0 upstream.

On the time to free xbc memory in xbc_exit(), memblock may has handed over memory to buddy allocator. So it doesn't make sense to free memory back to memblock. memblock_free() called by xbc_exit() even causes UAF bugs on architectures with CONFIG_ARCH_KEEP_MEMBLOCK disabled like x86. Following KASAN logs shows this case.

This patch fixes the xbc memory free problem by calling memblock_free() in early xbc init error rewind path and calling memblock_free_late() in xbc exit path to free memory to buddy allocator.

[    9.410890] ==================================================================
[    9.418962] BUG: KASAN: use-after-free in memblock_isolate_range+0x12d/0x260
[    9.426850] Read of size 8 at addr ffff88845dd30000 by task swapper/0/1

[    9.435901] CPU: 9 PID: 1 Comm: swapper/0 Tainted: G     U             6.9.0-rc3-00208-g586b5dfb51b9 #5
[    9.446403] Hardware name: Intel Corporation RPLP LP5 (CPU:RaptorLake)/RPLP LP5 (ID:13), BIOS IRPPN02.01.01.00.00.19.015.D-00000000 Dec 28 2023
[    9.460789] Call Trace:
[    9.463518]  <TASK>
[    9.465859]  dump_stack_lvl+0x53/0x70
[    9.469949]  print_report+0xce/0x610
[    9.473944]  ? __virt_addr_valid+0xf5/0x1b0
[    9.478619]  ? memblock_isolate_range+0x12d/0x260
[    9.483877]  kasan_report+0xc6/0x100
[    9.487870]  ? memblock_isolate_range+0x12d/0x260
[    9.493125]  memblock_isolate_range+0x12d/0x260
[    9.498187]  memblock_phys_free+0xb4/0x160
[    9.502762]  ? __pfx_memblock_phys_free+0x10/0x10
[    9.508021]  ? mutex_unlock+0x7e/0xd0
[    9.512111]  ? __pfx_mutex_unlock+0x10/0x10
[    9.516786]  ? kernel_init_freeable+0x2d4/0x430
[    9.521850]  ? __pfx_kernel_init+0x10/0x10
[    9.526426]  xbc_exit+0x17/0x70
[    9.529935]  kernel_init+0x38/0x1e0
[    9.533829]  ? _raw_spin_unlock_irq+0xd/0x30
[    9.538601]  ret_from_fork+0x2c/0x50
[    9.542596]  ? __pfx_kernel_init+0x10/0x10
[    9.547170]  ret_from_fork_asm+0x1a/0x30
[    9.551552]  </TASK>

[    9.555649] The buggy address belongs to the physical page:
[    9.561875] page: refcount:0 mapcount:0 mapping:0000000000000000 index:0x1 pfn:0x45dd30
[    9.570821] flags: 0x200000000000000(node=0|zone=2)
[    9.576271] page_type: 0xffffffff()
[    9.580167] raw: 0200000000000000 ffffea0011774c48 ffffea0012ba1848 0000000000000000
[    9.588823] raw: 0000000000000001 0000000000000000 00000000ffffffff 0000000000000000
[    9.597476] page dumped because: kasan: bad access detected

[    9.605362] Memory state around the buggy address:
[    9.610714]  ffff88845dd2ff00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[    9.618786]  ffff88845dd2ff80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[    9.626857] >ffff88845dd30000: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[    9.634930]                    ^
[    9.638534]  ffff88845dd30080: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[    9.646605]  ffff88845dd30100: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[    9.654675] ==================================================================

---
 include/linux/bootconfig.h |    7 ++++++-
 lib/bootconfig.c           |   19 +++++++++++--------
 2 files changed, 17 insertions(+), 9 deletions(-)

@@ -287,7 +287,12 @@ int __init xbc_init(const char *buf, siz
 int __init xbc_get_info(int *node_size, size_t *data_size);
 
 /* XBC cleanup data structures */
-void __init xbc_exit(void);
+void __init _xbc_exit(bool early);
+
+static inline void xbc_exit(void)
+{
+	_xbc_exit(false);
+}
 
 /* XBC embedded bootconfig data in kernel */
 #ifdef CONFIG_BOOT_CONFIG_EMBED

@@ -61,9 +61,12 @@ static inline void * __init xbc_alloc_me
 	return memblock_alloc(size, SMP_CACHE_BYTES);
 }
 
-static inline void __init xbc_free_mem(void *addr, size_t size)
+static inline void __init xbc_free_mem(void *addr, size_t size, bool early)
 {
-	memblock_free(addr, size);
+	if (early)
+		memblock_free(addr, size);
+	else if (addr)
+		memblock_free_late(__pa(addr), size);
 }
 
 #else /* !__KERNEL__ */

@@ -73,7 +76,7 @@ static inline void *xbc_alloc_mem(size_t
 	return malloc(size);
 }
 
-static inline void xbc_free_mem(void *addr, size_t size)
+static inline void xbc_free_mem(void *addr, size_t size, bool early)
 {
 	free(addr);
 }

@@ -904,13 +907,13 @@ static int __init xbc_parse_tree(void)
  * If you need to reuse xbc_init() with new boot config, you can
  * use this.
  */
-void __init xbc_exit(void)
+void __init _xbc_exit(bool early)
 {
-	xbc_free_mem(xbc_data, xbc_data_size);
+	xbc_free_mem(xbc_data, xbc_data_size, early);
 	xbc_data = NULL;
 	xbc_data_size = 0;
 	xbc_node_num = 0;
-	xbc_free_mem(xbc_nodes, sizeof(struct xbc_node) * XBC_NODE_MAX);
+	xbc_free_mem(xbc_nodes, sizeof(struct xbc_node) * XBC_NODE_MAX, early);
 	xbc_nodes = NULL;
 	brace_index = 0;
 }

@@ -963,7 +966,7 @@ int __init xbc_init(const char *data, si
 	if (!xbc_nodes) {
 		if (emsg)
 			*emsg = "Failed to allocate bootconfig nodes";
-		xbc_exit();
+		_xbc_exit(true);
 		return -ENOMEM;
 	}
 	memset(xbc_nodes, 0, sizeof(struct xbc_node) * XBC_NODE_MAX);

@@ -977,7 +980,7 @@ int __init xbc_init(const char *data, si
 			*epos = xbc_err_pos;
 		if (emsg)
 			*emsg = xbc_err_msg;
-		xbc_exit();
+		_xbc_exit(true);
 	} else
 		ret = xbc_node_num;
 

6.1-stable review patch. If anyone has any objections, please let me know.

------------------

From: Jeongjun Park <[email protected]>

commit c4a7dc9523b59b3e73fd522c73e95e072f876b16 upstream.

The size of the nilfs_type_by_mode array in the fs/nilfs2/dir.c file is defined as "S_IFMT >> S_SHIFT", but the nilfs_set_de_type() function, which uses this array, specifies the index to read from the array in the same way as "(mode & S_IFMT) >> S_SHIFT".

static void nilfs_set_de_type(struct nilfs_dir_entry *de, struct inode
*inode)

{
	umode_t mode = inode->i_mode;

	de->file_type = nilfs_type_by_mode[(mode & S_IFMT)>>S_SHIFT]; // oob
}

However, when the index is determined this way, an out-of-bounds (OOB) error occurs by referring to an index that is 1 larger than the array size when the condition "mode & S_IFMT == S_IFMT" is satisfied. Therefore, a patch to resize the nilfs_type_by_mode array should be applied to prevent OOB errors.

---
 fs/nilfs2/dir.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

@@ -243,7 +243,7 @@ nilfs_filetype_table[NILFS_FT_MAX] = {
 
 #define S_SHIFT 12
 static unsigned char
-nilfs_type_by_mode[S_IFMT >> S_SHIFT] = {
+nilfs_type_by_mode[(S_IFMT >> S_SHIFT) + 1] = {
 	[S_IFREG >> S_SHIFT]	= NILFS_FT_REG_FILE,
 	[S_IFDIR >> S_SHIFT]	= NILFS_FT_DIR,
 	[S_IFCHR >> S_SHIFT]	= NILFS_FT_CHRDEV,

6.1-stable review patch. If anyone has any objections, please let me know.

------------------

From: Arınç ÜNAL <[email protected]>

commit ff221029a51fd54cacac66e193e0c75e4de940e7 upstream.

MT7531_CPU_PMAP represents the destination port mask for trapped-to-CPU frames (further restricted by PCR_MATRIX).

Currently the driver sets the first CPU port as the single port in this bit mask, which works fine regardless of whether the device tree defines port 5, 6 or 5+6 as CPU ports. This is because the logic coincides with DSA's logic of picking the first CPU port as the CPU port that all user ports are affine to, by default.

An upcoming change would like to influence DSA's selection of the default CPU port to no longer be the first one, and in that case, this logic needs adaptation.

Since there is no observed leakage or duplication of frames if all CPU ports are defined in this bit mask, simply include them all.

---
 drivers/net/dsa/mt7530.c |   15 +++++++--------
 drivers/net/dsa/mt7530.h |    1 +
 2 files changed, 8 insertions(+), 8 deletions(-)

@@ -1236,6 +1236,13 @@ mt753x_cpu_port_enable(struct dsa_switch
 	if (priv->id == ID_MT7530 || priv->id == ID_MT7621)
 		mt7530_rmw(priv, MT7530_MFC, CPU_MASK, CPU_EN | CPU_PORT(port));
 
+	/* Add the CPU port to the CPU port bitmap for MT7531. Trapped frames
+	 * will be forwarded to the CPU port that is affine to the inbound user
+	 * port.
+	 */
+	if (priv->id == ID_MT7531)
+		mt7530_set(priv, MT7531_CFC, MT7531_CPU_PMAP(BIT(port)));
+
 	/* CPU port gets connected to all user ports of
 	 * the switch.
 	 */

@@ -2534,16 +2541,8 @@ static int
 mt7531_setup_common(struct dsa_switch *ds)
 {
 	struct mt7530_priv *priv = ds->priv;
-	struct dsa_port *cpu_dp;
 	int ret, i;
 
-	/* BPDU to CPU port */
-	dsa_switch_for_each_cpu_port(cpu_dp, ds) {
-		mt7530_rmw(priv, MT7531_CFC, MT7531_CPU_PMAP_MASK,
-			   BIT(cpu_dp->index));
-		break;
-	}
-
 	mt753x_trap_frames(priv);
 
 	/* Enable and reset MIB counters */

@@ -57,6 +57,7 @@ enum mt753x_id {
 #define  MT7531_MIRROR_PORT_GET(x)	(((x) >> 16) & MIRROR_MASK)
 #define  MT7531_MIRROR_PORT_SET(x)	(((x) & MIRROR_MASK) << 16)
 #define  MT7531_CPU_PMAP_MASK		GENMASK(7, 0)
+#define  MT7531_CPU_PMAP(x)		FIELD_PREP(MT7531_CPU_PMAP_MASK, x)
 
 #define MT753X_MIRROR_REG(id)		(((id) == ID_MT7531) ? \
 					 MT7531_CFC : MT7530_MFC)

6.1-stable review patch. If anyone has any objections, please let me know.

------------------

From: Vladimir Oltean <[email protected]>

commit b79d7c14f48083abb3fb061370c0c64a569edf4c upstream.

Since the introduction of the OF bindings, DSA has always had a policy that in case multiple CPU ports are present in the device tree, the numerically smallest one is always chosen.

The MT7530 switch family, except the switch on the MT7988 SoC, has 2 CPU ports, 5 and 6, where port 6 is preferable on the MT7531BE switch because it has higher bandwidth.

The MT7530 driver developers had 3 options:
- to modify DSA when the MT7531 switch support was introduced, such as to prefer the better port
- to declare both CPU ports in device trees as CPU ports, and live with the sub-optimal performance resulting from not preferring the better port
- to declare just port 6 in the device tree as a CPU port

Of course they chose the path of least resistance (3rd option), kicking the can down the road. The hardware description in the device tree is supposed to be stable - developers are not supposed to adopt the strategy of piecemeal hardware description, where the device tree is updated in lockstep with the features that the kernel currently supports.

Now, as a result of the fact that they did that, any attempts to modify the device tree and describe both CPU ports as CPU ports would make DSA change its default selection from port 6 to 5, effectively resulting in a performance degradation visible to users with the MT7531BE switch as can be seen below.

Without preferring port 6:

[ ID][Role] Interval Transfer Bitrate Retr

[  5][TX-C]   0.00-20.00  sec   374 MBytes   157 Mbits/sec  734    sender
[  5][TX-C]   0.00-20.00  sec   373 MBytes   156 Mbits/sec    receiver
[  7][RX-C]   0.00-20.00  sec  1.81 GBytes   778 Mbits/sec    0    sender
[  7][RX-C]   0.00-20.00  sec  1.81 GBytes   777 Mbits/sec    receiver

With preferring port 6:

[ ID][Role] Interval           Transfer     Bitrate         Retr
[  5][TX-C]   0.00-20.00  sec  1.99 GBytes   856 Mbits/sec  273    sender
[  5][TX-C]   0.00-20.00  sec  1.99 GBytes   855 Mbits/sec    receiver
[  7][RX-C]   0.00-20.00  sec  1.72 GBytes   737 Mbits/sec   15    sender
[  7][RX-C]   0.00-20.00  sec  1.71 GBytes   736 Mbits/sec    receiver

Using one port for WAN and the other ports for LAN is a very popular use case which is what this test emulates.

As such, this change proposes that we retroactively modify stable kernels (which don't support the modification of the CPU port assignments, so as to let user space fix the problem and restore the throughput) to keep the mt7530 driver preferring port 6 even with device trees where the hardware is more fully described.

---
 drivers/net/dsa/mt7530.c |   15 +++++++++++++++
 include/net/dsa.h        |    8 ++++++++
 net/dsa/dsa2.c           |   24 +++++++++++++++++++++++-
 3 files changed, 46 insertions(+), 1 deletion(-)

@@ -419,6 +419,20 @@ static void mt7530_pll_setup(struct mt75
 	core_set(priv, CORE_TRGMII_GSW_CLK_CG, REG_GSWCK_EN);
 }
 
+/* If port 6 is available as a CPU port, always prefer that as the default,
+ * otherwise don't care.
+ */
+static struct dsa_port *
+mt753x_preferred_default_local_cpu_port(struct dsa_switch *ds)
+{
+	struct dsa_port *cpu_dp = dsa_to_port(ds, 6);
+
+	if (dsa_port_is_cpu(cpu_dp))
+		return cpu_dp;
+
+	return NULL;
+}
+
 /* Setup port 6 interface mode and TRGMII TX circuit */
 static int
 mt7530_pad_clk_setup(struct dsa_switch *ds, phy_interface_t interface)

@@ -3405,6 +3419,7 @@ static int mt753x_set_mac_eee(struct dsa
 static const struct dsa_switch_ops mt7530_switch_ops = {
 	.get_tag_protocol	= mtk_get_tag_protocol,
 	.setup			= mt753x_setup,
+	.preferred_default_local_cpu_port = mt753x_preferred_default_local_cpu_port,
 	.get_strings		= mt7530_get_strings,
 	.get_ethtool_stats	= mt7530_get_ethtool_stats,
 	.get_sset_count		= mt7530_get_sset_count,

@@ -969,6 +969,14 @@ struct dsa_switch_ops {
 	void	(*port_disable)(struct dsa_switch *ds, int port);
 
 	/*
+	 * Compatibility between device trees defining multiple CPU ports and
+	 * drivers which are not OK to use by default the numerically smallest
+	 * CPU port of a switch for its local ports. This can return NULL,
+	 * meaning "don't know/don't care".
+	 */
+	struct dsa_port *(*preferred_default_local_cpu_port)(struct dsa_switch *ds);
+
+	/*
 	 * Port's MAC EEE settings
 	 */
 	int	(*set_mac_eee)(struct dsa_switch *ds, int port,

@@ -425,6 +425,24 @@ static int dsa_tree_setup_default_cpu(st
 	return 0;
 }
 
+static struct dsa_port *
+dsa_switch_preferred_default_local_cpu_port(struct dsa_switch *ds)
+{
+	struct dsa_port *cpu_dp;
+
+	if (!ds->ops->preferred_default_local_cpu_port)
+		return NULL;
+
+	cpu_dp = ds->ops->preferred_default_local_cpu_port(ds);
+	if (!cpu_dp)
+		return NULL;
+
+	if (WARN_ON(!dsa_port_is_cpu(cpu_dp) || cpu_dp->ds != ds))
+		return NULL;
+
+	return cpu_dp;
+}
+
 /* Perform initial assignment of CPU ports to user ports and DSA links in the
  * fabric, giving preference to CPU ports local to each switch. Default to
  * using the first CPU port in the switch tree if the port does not have a CPU

@@ -432,12 +450,16 @@ static int dsa_tree_setup_default_cpu(st
  */
 static int dsa_tree_setup_cpu_ports(struct dsa_switch_tree *dst)
 {
-	struct dsa_port *cpu_dp, *dp;
+	struct dsa_port *preferred_cpu_dp, *cpu_dp, *dp;
 
 	list_for_each_entry(cpu_dp, &dst->ports, list) {
 		if (!dsa_port_is_cpu(cpu_dp))
 			continue;
 
+		preferred_cpu_dp = dsa_switch_preferred_default_local_cpu_port(cpu_dp->ds);
+		if (preferred_cpu_dp && preferred_cpu_dp != cpu_dp)
+			continue;
+
 		/* Prefer a local CPU port */
 		dsa_switch_for_each_port(dp, cpu_dp->ds) {
 			/* Prefer the first local CPU port found */

6.1-stable review patch. If anyone has any objections, please let me know.

------------------

From: Arınç ÜNAL <[email protected]>

commit 5f563c31ff0c40ce395d0bae7daa94c7950dac97 upstream.

The MT7530 switch after reset initialises with a core clock frequency that works with a 25MHz XTAL connected to it. For 40MHz XTAL, the core clock frequency must be set to 500MHz.

The mt7530_pll_setup() function is responsible of setting the core clock frequency. Currently, it runs on MT7530 with 25MHz and 40MHz XTAL. This causes MT7530 switch with 25MHz XTAL to egress and ingress frames improperly.

Introduce a check to run it only on MT7530 with 40MHz XTAL.

The core clock frequency is set by writing to a switch PHY's register. Access to the PHY's register is done via the MDIO bus the switch is also on. Therefore, it works only when the switch makes switch PHYs listen on the MDIO bus the switch is on. This is controlled either by the state of the ESW_P1_LED_1 pin after reset deassertion or modifying bit 5 of the modifiable trap register.

When ESW_P1_LED_1 is pulled high, PHY indirect access is used. That means accessing PHY registers via the PHY indirect access control register of the switch.

When ESW_P1_LED_1 is pulled low, PHY direct access is used. That means accessing PHY registers via the MDIO bus the switch is on.

For MT7530 switch with 40MHz XTAL on a board with ESW_P1_LED_1 pulled high, the core clock frequency won't be set to 500MHz, causing the switch to egress and ingress frames improperly.

Run mt7530_pll_setup() after PHY direct access is set on the modifiable trap register.

With these two changes, all MT7530 switches with 25MHz and 40MHz, and P1_LED_1 pulled high or low, will egress and ingress frames properly.

---
 drivers/net/dsa/mt7530.c |    5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

@@ -2434,8 +2434,6 @@ mt7530_setup(struct dsa_switch *ds)
 		     SYS_CTRL_PHY_RST | SYS_CTRL_SW_RST |
 		     SYS_CTRL_REG_RST);
 
-	mt7530_pll_setup(priv);
-
 	/* Lower Tx driving for TRGMII path */
 	for (i = 0; i < NUM_TRGMII_CTRL; i++)
 		mt7530_write(priv, MT7530_TRGMII_TD_ODT(i),

@@ -2453,6 +2451,9 @@ mt7530_setup(struct dsa_switch *ds)
 
 	priv->p6_interface = PHY_INTERFACE_MODE_NA;
 
+	if ((val & HWTRAP_XTAL_MASK) == HWTRAP_XTAL_40MHZ)
+		mt7530_pll_setup(priv);
+
 	mt753x_trap_frames(priv);
 
 	/* Enable and reset MIB counters */

6.1-stable review patch. If anyone has any objections, please let me know.

------------------

From: Arınç ÜNAL <[email protected]>

commit 06dfcd4098cfdc4d4577d94793a4f9125386da8b upstream.

The commit 40b5d2f15c09 ("net: dsa: mt7530: Add support for EEE features") brought EEE support but did not enable EEE on MT7531 switch MACs. EEE is enabled on MT7531 switch MACs by pulling the LAN2LED0 pin low on the board (bootstrapping), unsetting the EEE_DIS bit on the trap register, or setting the internal EEE switch bit on the CORE_PLL_GROUP4 register. Thanks to SkyLake Huang (黃啟澤) from MediaTek for providing information on the internal EEE switch bit.

There are existing boards that were not designed to pull the pin low. Because of that, the EEE status currently depends on the board design.

The EEE_DIS bit on the trap pertains to the LAN2LED0 pin which is usually used to control an LED. Once the bit is unset, the pin will be low. That will make the active low LED turn on. The pin is controlled by the switch PHY. It seems that the PHY controls the pin in the way that it inverts the pin state. That means depending on the wiring of the LED connected to LAN2LED0 on the board, the LED may be on without an active link.

To not cause this unwanted behaviour whilst enabling EEE on all boards, set the internal EEE switch bit on the CORE_PLL_GROUP4 register.

My testing on MT7531 shows a certain amount of traffic loss when EEE is enabled. That said, I haven't come across a board that enables EEE. So enable EEE on the switch MACs but disable EEE advertisement on the switch PHYs. This way, we don't change the behaviour of the majority of the boards that have this switch. The mediatek-ge PHY driver already disables EEE advertisement on the switch PHYs but my testing shows that it is somehow enabled afterwards. Disabling EEE advertisement before the PHY driver initialises keeps it off.

With this change, EEE can now be enabled using ethtool.

---
 drivers/net/dsa/mt7530.c |   17 ++++++++++++-----
 drivers/net/dsa/mt7530.h |    1 +
 2 files changed, 13 insertions(+), 5 deletions(-)

@@ -2675,18 +2675,25 @@ mt7531_setup(struct dsa_switch *ds)
 	priv->p5_interface = PHY_INTERFACE_MODE_NA;
 	priv->p6_interface = PHY_INTERFACE_MODE_NA;
 
-	/* Enable PHY core PLL, since phy_device has not yet been created
-	 * provided for phy_[read,write]_mmd_indirect is called, we provide
-	 * our own mt7531_ind_mmd_phy_[read,write] to complete this
-	 * function.
+	/* Enable Energy-Efficient Ethernet (EEE) and PHY core PLL, since
+	 * phy_device has not yet been created provided for
+	 * phy_[read,write]_mmd_indirect is called, we provide our own
+	 * mt7531_ind_mmd_phy_[read,write] to complete this function.
 	 */
 	val = mt7531_ind_c45_phy_read(priv, MT753X_CTRL_PHY_ADDR,
 				      MDIO_MMD_VEND2, CORE_PLL_GROUP4);
-	val |= MT7531_PHY_PLL_BYPASS_MODE;
+	val |= MT7531_RG_SYSPLL_DMY2 | MT7531_PHY_PLL_BYPASS_MODE;
 	val &= ~MT7531_PHY_PLL_OFF;
 	mt7531_ind_c45_phy_write(priv, MT753X_CTRL_PHY_ADDR, MDIO_MMD_VEND2,
 				 CORE_PLL_GROUP4, val);
 
+	/* Disable EEE advertisement on the switch PHYs. */
+	for (i = MT753X_CTRL_PHY_ADDR;
+	     i < MT753X_CTRL_PHY_ADDR + MT7530_NUM_PHYS; i++) {
+		mt7531_ind_c45_phy_write(priv, i, MDIO_MMD_AN, MDIO_AN_EEE_ADV,
+					 0);
+	}
+
 	mt7531_setup_common(ds);
 
 	/* Setup VLAN ID 0 for VLAN-unaware bridges */

@@ -673,6 +673,7 @@ enum mt7531_clk_skew {
 #define  RG_SYSPLL_DDSFBK_EN		BIT(12)
 #define  RG_SYSPLL_BIAS_EN		BIT(11)
 #define  RG_SYSPLL_BIAS_LPF_EN		BIT(10)
+#define  MT7531_RG_SYSPLL_DMY2		BIT(6)
 #define  MT7531_PHY_PLL_OFF		BIT(5)
 #define  MT7531_PHY_PLL_BYPASS_MODE	BIT(4)
 

6.1-stable review patch. If anyone has any objections, please let me know.

------------------

From: Namjae Jeon <[email protected]>

commit c119f4ede3fa90a9463f50831761c28f989bfb20 upstream.

If ->ProtocolId is SMB2_TRANSFORM_PROTO_NUM, smb2 request size validation could be skipped. if request size is smaller than sizeof(struct smb2_query_info_req), slab-out-of-bounds read can happen in smb2_allocate_rsp_buf(). This patch allocate response buffer after decrypting transform request. smb3_decrypt_req() will validate transform request size and avoid slab-out-of-bound in smb2_allocate_rsp_buf().

---
 fs/smb/server/server.c |   13 +++++--------
 1 file changed, 5 insertions(+), 8 deletions(-)

@@ -167,20 +167,17 @@ static void __handle_ksmbd_work(struct k
 	int rc;
 	bool is_chained = false;
 
-	if (conn->ops->allocate_rsp_buf(work))
-		return;
-
 	if (conn->ops->is_transform_hdr &&
 	    conn->ops->is_transform_hdr(work->request_buf)) {
 		rc = conn->ops->decrypt_req(work);
-		if (rc < 0) {
-			conn->ops->set_rsp_status(work, STATUS_DATA_ERROR);
-			goto send;
-		}
-
+		if (rc < 0)
+			return;
 		work->encrypted = true;
 	}
 
+	if (conn->ops->allocate_rsp_buf(work))
+		return;
+
 	rc = conn->ops->init_rsp_hdr(work);
 	if (rc) {
 		/* either uid or tid is not correct */

6.1-stable review patch. If anyone has any objections, please let me know.

------------------

From: Namjae Jeon <[email protected]>

commit 17cf0c2794bdb6f39671265aa18aea5c22ee8c4a upstream.

The response buffer should be allocated in smb2_allocate_rsp_buf before validating request. But the fields in payload as well as smb2 header is used in smb2_allocate_rsp_buf(). This patch add simple buffer size validation to avoid potencial out-of-bounds in request buffer.

---
 fs/smb/server/smb2pdu.c |    4 ++++
 1 file changed, 4 insertions(+)

@@ -534,6 +534,10 @@ int smb2_allocate_rsp_buf(struct ksmbd_w
 	if (cmd == SMB2_QUERY_INFO_HE) {
 		struct smb2_query_info_req *req;
 
+		if (get_rfc1002_len(work->request_buf) <
+		    offsetof(struct smb2_query_info_req, OutputBufferLength))
+			return -EINVAL;
+
 		req = smb2_get_msg(work->request_buf);
 		if ((req->InfoType == SMB2_O_INFO_FILE &&
 		     (req->FileInfoClass == FILE_FULL_EA_INFORMATION ||

6.1-stable review patch. If anyone has any objections, please let me know.

------------------

From: Marios Makassikis <[email protected]>

commit 4973b04d3ea577db80c501c5f14e68ec69fe1794 upstream.

File overwrite case is explicitly handled, so it is not necessary to pass RENAME_NOREPLACE to vfs_rename.

Clearing the flag fixes rename operations when the share is a ntfs-3g mount. The latter uses an older version of fuse with no support for flags in the ->rename op.

---
 fs/smb/server/vfs.c |    5 +++++
 1 file changed, 5 insertions(+)

@@ -746,10 +746,15 @@ retry:
 		goto out4;
 	}
 
+	/*
+	 * explicitly handle file overwrite case, for compatibility with
+	 * filesystems that may not support rename flags (e.g: fuse)
+	 */
 	if ((flags & RENAME_NOREPLACE) && d_is_positive(new_dentry)) {
 		err = -EEXIST;
 		goto out4;
 	}
+	flags &= ~(RENAME_NOREPLACE);
 
 	if (old_child == trap) {
 		err = -EINVAL;

6.1-stable review patch. If anyone has any objections, please let me know.

------------------

From: Namjae Jeon <[email protected]>

commit 0268a7cc7fdc47d90b6c18859de7718d5059f6f1 upstream.

4byte padding cause the connection issue with the applications of MacOS. smb2_close response size increases by 4 bytes by padding, And the smb client of MacOS check it and stop the connection. This patch use struct_group_attr instead of struct_group for network_open_info to use
__packed to avoid padding.

---
 fs/smb/common/smb2pdu.h |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

@@ -699,7 +699,7 @@ struct smb2_close_rsp {
 	__le16 StructureSize; /* 60 */
 	__le16 Flags;
 	__le32 Reserved;
-	struct_group(network_open_info,
+	struct_group_attr(network_open_info, __packed,
 		__le64 CreationTime;
 		__le64 LastAccessTime;
 		__le64 LastWriteTime;

6.1-stable review patch. If anyone has any objections, please let me know.

------------------

From: Johan Hovold <[email protected]>

commit 1e560864159d002b453da42bd2c13a1805515a20 upstream.

A last minute revert in 6.7-final introduced a potential deadlock when enabling ASPM during probe of Qualcomm PCIe controllers as reported by lockdep:

============================================
WARNING: possible recursive locking detected
6.7.0 #40 Not tainted
--------------------------------------------
kworker/u16:5/90 is trying to acquire lock:
ffffacfa78ced000 (pci_bus_sem){++++}-{3:3}, at: pcie_aspm_pm_state_change+0x58/0xdc

but task is already holding lock:
ffffacfa78ced000 (pci_bus_sem){++++}-{3:3}, at: pci_walk_bus+0x34/0xbc

other info that might help us debug this:

   Possible unsafe locking scenario:

         CPU0
         ----
    lock(pci_bus_sem);
    lock(pci_bus_sem);

               *** DEADLOCK ***

  Call trace:
   print_deadlock_bug+0x25c/0x348
   __lock_acquire+0x10a4/0x2064
   lock_acquire+0x1e8/0x318
   down_read+0x60/0x184
   pcie_aspm_pm_state_change+0x58/0xdc
   pci_set_full_power_state+0xa8/0x114
   pci_set_power_state+0xc4/0x120
   qcom_pcie_enable_aspm+0x1c/0x3c [pcie_qcom]
   pci_walk_bus+0x64/0xbc
   qcom_pcie_host_post_init_2_7_0+0x28/0x34 [pcie_qcom]

The deadlock can easily be reproduced on machines like the Lenovo ThinkPad X13s by adding a delay to increase the race window during asynchronous probe where another thread can take a write lock.

Add a new pci_set_power_state_locked() and associated helper functions that can be called with the PCI bus semaphore held to avoid taking the read lock twice.

[bhelgaas: backported to v6.1.y, which contains b9c370b61d73 ("Revert
"PCI/ASPM: Remove pcie_aspm_pm_state_change()""), a backport of f93e71aea6c6. This omits the drivers/pci/controller/dwc/pcie-qcom.c hunk that updates qcom_pcie_enable_aspm(), which was added by 9f4f3dfad8cf ("PCI: qcom: Enable ASPM for platforms supporting 1.9.0 ops"), which is not present in v6.1.87.]

---
 drivers/pci/bus.c       |   49 +++++++++++++++++++-----------
 drivers/pci/pci.c       |   78 ++++++++++++++++++++++++++++++++----------------
 drivers/pci/pci.h       |    4 +-
 drivers/pci/pcie/aspm.c |   13 +++++---
 include/linux/pci.h     |    5 +++
 5 files changed, 100 insertions(+), 49 deletions(-)

@@ -379,21 +379,8 @@ void pci_bus_add_devices(const struct pc
 }
 EXPORT_SYMBOL(pci_bus_add_devices);
 
-/** pci_walk_bus - walk devices on/under bus, calling callback.
- *  @top      bus whose devices should be walked
- *  @cb       callback to be called for each device found
- *  @userdata arbitrary pointer to be passed to callback.
- *
- *  Walk the given bus, including any bridged devices
- *  on buses under this bus.  Call the provided callback
- *  on each device found.
- *
- *  We check the return of @cb each time. If it returns anything
- *  other than 0, we break out.
- *
- */
-void pci_walk_bus(struct pci_bus *top, int (*cb)(struct pci_dev *, void *),
-		  void *userdata)
+static void __pci_walk_bus(struct pci_bus *top, int (*cb)(struct pci_dev *, void *),
+			   void *userdata, bool locked)
 {
 	struct pci_dev *dev;
 	struct pci_bus *bus;

@@ -401,7 +388,8 @@ void pci_walk_bus(struct pci_bus *top, i
 	int retval;
 
 	bus = top;
-	down_read(&pci_bus_sem);
+	if (!locked)
+		down_read(&pci_bus_sem);
 	next = top->devices.next;
 	for (;;) {
 		if (next == &bus->devices) {

@@ -424,10 +412,37 @@ void pci_walk_bus(struct pci_bus *top, i
 		if (retval)
 			break;
 	}
-	up_read(&pci_bus_sem);
+	if (!locked)
+		up_read(&pci_bus_sem);
+}
+
+/**
+ *  pci_walk_bus - walk devices on/under bus, calling callback.
+ *  @top: bus whose devices should be walked
+ *  @cb: callback to be called for each device found
+ *  @userdata: arbitrary pointer to be passed to callback
+ *
+ *  Walk the given bus, including any bridged devices
+ *  on buses under this bus.  Call the provided callback
+ *  on each device found.
+ *
+ *  We check the return of @cb each time. If it returns anything
+ *  other than 0, we break out.
+ */
+void pci_walk_bus(struct pci_bus *top, int (*cb)(struct pci_dev *, void *), void *userdata)
+{
+	__pci_walk_bus(top, cb, userdata, false);
 }
 EXPORT_SYMBOL_GPL(pci_walk_bus);
 
+void pci_walk_bus_locked(struct pci_bus *top, int (*cb)(struct pci_dev *, void *), void *userdata)
+{
+	lockdep_assert_held(&pci_bus_sem);
+
+	__pci_walk_bus(top, cb, userdata, true);
+}
+EXPORT_SYMBOL_GPL(pci_walk_bus_locked);
+
 struct pci_bus *pci_bus_get(struct pci_bus *bus)
 {
 	if (bus)

@@ -556,12 +556,12 @@ bool pcie_wait_for_link(struct pci_dev *
 #ifdef CONFIG_PCIEASPM
 void pcie_aspm_init_link_state(struct pci_dev *pdev);
 void pcie_aspm_exit_link_state(struct pci_dev *pdev);
-void pcie_aspm_pm_state_change(struct pci_dev *pdev);
+void pcie_aspm_pm_state_change(struct pci_dev *pdev, bool locked);
 void pcie_aspm_powersave_config_link(struct pci_dev *pdev);
 #else
 static inline void pcie_aspm_init_link_state(struct pci_dev *pdev) { }
 static inline void pcie_aspm_exit_link_state(struct pci_dev *pdev) { }
-static inline void pcie_aspm_pm_state_change(struct pci_dev *pdev) { }
+static inline void pcie_aspm_pm_state_change(struct pci_dev *pdev, bool locked) { }
 static inline void pcie_aspm_powersave_config_link(struct pci_dev *pdev) { }
 #endif
 

@@ -1055,8 +1055,11 @@ void pcie_aspm_exit_link_state(struct pc
 	up_read(&pci_bus_sem);
 }
 
-/* @pdev: the root port or switch downstream port */
-void pcie_aspm_pm_state_change(struct pci_dev *pdev)
+/*
+ * @pdev: the root port or switch downstream port
+ * @locked: whether pci_bus_sem is held
+ */
+void pcie_aspm_pm_state_change(struct pci_dev *pdev, bool locked)
 {
 	struct pcie_link_state *link = pdev->link_state;
 

@@ -1066,12 +1069,14 @@ void pcie_aspm_pm_state_change(struct pc
 	 * Devices changed PM state, we should recheck if latency
 	 * meets all functions' requirement
 	 */
-	down_read(&pci_bus_sem);
+	if (!locked)
+		down_read(&pci_bus_sem);
 	mutex_lock(&aspm_lock);
 	pcie_update_aspm_capable(link->root);
 	pcie_config_aspm_path(link);
 	mutex_unlock(&aspm_lock);
-	up_read(&pci_bus_sem);
+	if (!locked)
+		up_read(&pci_bus_sem);
 }
 
 void pcie_aspm_powersave_config_link(struct pci_dev *pdev)

@@ -1383,6 +1383,7 @@ int pci_load_and_free_saved_state(struct
 				  struct pci_saved_state **state);
 int pci_platform_power_transition(struct pci_dev *dev, pci_power_t state);
 int pci_set_power_state(struct pci_dev *dev, pci_power_t state);
+int pci_set_power_state_locked(struct pci_dev *dev, pci_power_t state);
 pci_power_t pci_choose_state(struct pci_dev *dev, pm_message_t state);
 bool pci_pme_capable(struct pci_dev *dev, pci_power_t state);
 void pci_pme_active(struct pci_dev *dev, bool enable);

@@ -1553,6 +1554,8 @@ int pci_scan_bridge(struct pci_bus *bus,
 
 void pci_walk_bus(struct pci_bus *top, int (*cb)(struct pci_dev *, void *),
 		  void *userdata);
+void pci_walk_bus_locked(struct pci_bus *top, int (*cb)(struct pci_dev *, void *),
+			 void *userdata);
 int pci_cfg_space_size(struct pci_dev *dev);
 unsigned char pci_bus_max_busnr(struct pci_bus *bus);
 void pci_setup_bridge(struct pci_bus *bus);

@@ -1884,6 +1887,8 @@ static inline int pci_save_state(struct
 static inline void pci_restore_state(struct pci_dev *dev) { }
 static inline int pci_set_power_state(struct pci_dev *dev, pci_power_t state)
 { return 0; }
+static inline int pci_set_power_state_locked(struct pci_dev *dev, pci_power_t state)
+{ return 0; }
 static inline int pci_wake_from_d3(struct pci_dev *dev, bool enable)
 { return 0; }
 static inline pci_power_t pci_choose_state(struct pci_dev *dev,

Hello,

This rc kernel passes DAMON functionality test[1] on my test machine. Attaching the test results summary below. Please note that I retrieved the kernel from linux-stable-rc tree[2].

[1] https://github.com/awslabs/damon-tests/tree/next/corr
[2] cde450ef0f2f ("Linux 6.1.88-rc1")

Thanks,
SJ

[...]

---

ok 1 selftests: damon: debugfs_attrs.sh
ok 2 selftests: damon: debugfs_schemes.sh
ok 3 selftests: damon: debugfs_target_ids.sh
ok 4 selftests: damon: debugfs_empty_targets.sh
ok 5 selftests: damon: debugfs_huge_count_read_write.sh
ok 6 selftests: damon: debugfs_duplicate_context_creation.sh
ok 7 selftests: damon: sysfs.sh
ok 1 selftests: damon-tests: kunit.sh
ok 2 selftests: damon-tests: huge_count_read_write.sh
ok 3 selftests: damon-tests: buffer_overflow.sh
ok 4 selftests: damon-tests: rm_contexts.sh
ok 5 selftests: damon-tests: record_null_deref.sh
ok 6 selftests: damon-tests: dbgfs_target_ids_read_before_terminate_race.sh ok 7 selftests: damon-tests: dbgfs_target_ids_pid_leak.sh
ok 8 selftests: damon-tests: damo_tests.sh
ok 9 selftests: damon-tests: masim-record.sh
ok 10 selftests: damon-tests: build_i386.sh
ok 11 selftests: damon-tests: build_arm64.sh
ok 12 selftests: damon-tests: build_m68k.sh
ok 13 selftests: damon-tests: build_i386_idle_flag.sh
ok 14 selftests: damon-tests: build_i386_highpte.sh
ok 15 selftests: damon-tests: build_nomemcg.sh
[33m
[92mPASS [39m

Hi!

This causes compilation errors in our testing:

arch/arm/mach-omap2/pdata-quirks.c:259:15: error: variable 'pandora_soc_audio_gpios' has initializer but incomplete type
1991 259 | static struct gpiod_lookup_table pandora_soc_audio_gpios = {
1992 | ^~~~~~~~~~~~~~~~~~
1993arch/arm/mach-omap2/pdata-quirks.c:260:10: error: 'struct gpiod_lookup_table' has no member named 'dev_id'
1994 260 | .dev_id = "soc-audio",
1995 | ^~~~~~
1996arch/arm/mach-omap2/pdata-quirks.c:260:19: warning: excess elements in struct initializer
1997 260 | .dev_id = "soc-audio",
1998 | ^~~~~~~~~~~
1999arch/arm/mach-omap2/pdata-quirks.c:260:19: note: (near initialization for 'pandora_soc_audio_gpios') 2000arch/arm/mach-omap2/pdata-quirks.c:261:10: error: 'struct gpiod_lookup_table' has no member named 'table'
2001 261 | .table = {
2002 | ^~~~~
2003arch/arm/mach-omap2/pdata-quirks.c:261:18: error: extra brace group at end of initializer
2004 261 | .table = {
2005 | ^
2006arch/arm/mach-omap2/pdata-quirks.c:261:18: note: (near initialization for 'pandora_soc_audio_gpios') 2007arch/arm/mach-omap2/pdata-quirks.c:262:17: error: implicit declaration of function 'GPIO_LOOKUP'; did you mean 'IOP_LOOKUP'? [-Werror=implicit-function-declaration]

2008  262 |                 GPIO_LOOKUP("gpio-112-127", 6, "dac", GPIO_ACTIVE_HIGH),
2009      |                 ^~~~~~~~~~~
2010      |                 IOP_LOOKUP
2011arch/arm/mach-omap2/pdata-quirks.c:262:55: error: 'GPIO_ACTIVE_HIGH' undeclared here (not in a function); did you mean 'ACPI_ACTIVE_HIGH'?
2012  262 |                 GPIO_LOOKUP("gpio-112-127", 6, "dac", GPIO_ACTIVE_HIGH),
2013      |                                                       ^~~~~~~~~~~~~~~~
2014      |                                                       ACPI_ACTIVE_HIGH
2015arch/arm/mach-omap2/pdata-quirks.c:264:17: error: extra brace group at end of initializer
2016  264 |                 { }
2017      |                 ^

2018arch/arm/mach-omap2/pdata-quirks.c:264:17: note: (near initialization for 'pandora_soc_audio_gpios') 2019arch/arm/mach-omap2/pdata-quirks.c:261:18: warning: excess elements in struct initializer
2020 261 | .table = {
2021 | ^
2022arch/arm/mach-omap2/pdata-quirks.c:261:18: note: (near initialization for 'pandora_soc_audio_gpios')
2023 CC net/sched/sch_api.o
2024arch/arm/mach-omap2/pdata-quirks.c: In function 'omap3_pandora_legacy_init':
2025arch/arm/mach-omap2/pdata-quirks.c:271:9: error: implicit declaration of function 'gpiod_add_lookup_table' [-Werror=implicit-function-declaration]

2026  271 |         gpiod_add_lookup_table(&pandora_soc_audio_gpios);
2027      |         ^~~~~~~~~~~~~~~~~~~~~~

2028arch/arm/mach-omap2/pdata-quirks.c: At top level:
2029arch/arm/mach-omap2/pdata-quirks.c:259:34: error: storage size of 'pandora_soc_audio_gpios' isn't known 2030 259 | static struct gpiod_lookup_table pandora_soc_audio_gpios = {
2031 | ^~~~~~~~~~~~~~~~~~~~~~~
2032cc1: some warnings being treated as errors
2033make[2]: *** [scripts/Makefile.build:250: arch/arm/mach-omap2/pdata-quirks.o] Error 1 2034make[1]: *** [scripts/Makefile.build:500: arch/arm/mach-omap2] Error 2
2035make[1]: *** Waiting for unfinished jobs....
2036

https://gitlab.com/cip-project/cip-testing/linux-stable-rc-ci/-/jobs/6700371466
https://gitlab.com/cip-project/cip-testing/linux-stable-rc-ci/-/pipelines/1265143103

Best regards,
Pavel

DENX Software Engineering GmbH,        Managing Director: Erika Unter
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany

As Pavel reported,

LKFT also found these regressions on 6.1.

The arm build failed with gcc-13 and clang-17 on the Linux stable-rc linux.6.1.y branch.

arm:
* omap2plus_defconfig - failed
* defconfig - failed

Suspecting commit :
-------
ASoC: ti: Convert Pandora ASoC to GPIO descriptors

    [ Upstream commit 319e6ac143b9e9048e527ab9dd2aabb8fdf3d60f ]

Build log:
---
arch/arm/mach-omap2/pdata-quirks.c:259:15: error: variable 'pandora_soc_audio_gpios' has initializer but incomplete type

  259 | static struct gpiod_lookup_table pandora_soc_audio_gpios = {
      |               ^~~~~~~~~~~~~~~~~~
arch/arm/mach-omap2/pdata-quirks.c:260:10: error: 'struct
gpiod_lookup_table' has no member named 'dev_id'
  260 |         .dev_id = "soc-audio",
      |          ^~~~~~
arch/arm/mach-omap2/pdata-quirks.c:260:19: warning: excess elements in
struct initializer
  260 |         .dev_id = "soc-audio",
      |                   ^~~~~~~~~~~

arch/arm/mach-omap2/pdata-quirks.c:260:19: note: (near initialization for 'pandora_soc_audio_gpios') arch/arm/mach-omap2/pdata-quirks.c:261:10: error: 'struct gpiod_lookup_table' has no member named 'table'

  261 |         .table = {
      |          ^~~~~

arch/arm/mach-omap2/pdata-quirks.c:261:18: error: extra brace group at end of initializer
261 | .table = {
| ^
arch/arm/mach-omap2/pdata-quirks.c:261:18: note: (near initialization for 'pandora_soc_audio_gpios') arch/arm/mach-omap2/pdata-quirks.c:262:17: error: implicit declaration of function 'GPIO_LOOKUP'; did you mean 'IOP_LOOKUP'? [-Werror=implicit-function-declaration]

  262 |                 GPIO_LOOKUP("gpio-112-127", 6, "dac", GPIO_ACTIVE_HIGH),
      |                 ^~~~~~~~~~~
      |                 IOP_LOOKUP
arch/arm/mach-omap2/pdata-quirks.c:262:55: error: 'GPIO_ACTIVE_HIGH'
undeclared here (not in a function); did you mean 'ACPI_ACTIVE_HIGH'?
  262 |                 GPIO_LOOKUP("gpio-112-127", 6, "dac", GPIO_ACTIVE_HIGH),
      |                                                       ^~~~~~~~~~~~~~~~
      |                                                       ACPI_ACTIVE_HIGH
arch/arm/mach-omap2/pdata-quirks.c:264:17: error: extra brace group at
end of initializer
  264 |                 { }
      |                 ^

arch/arm/mach-omap2/pdata-quirks.c:264:17: note: (near initialization for 'pandora_soc_audio_gpios') arch/arm/mach-omap2/pdata-quirks.c:261:18: warning: excess elements in struct initializer
261 | .table = {
| ^
arch/arm/mach-omap2/pdata-quirks.c:261:18: note: (near initialization for 'pandora_soc_audio_gpios') arch/arm/mach-omap2/pdata-quirks.c: In function 'omap3_pandora_legacy_init':
arch/arm/mach-omap2/pdata-quirks.c:271:9: error: implicit declaration of function 'gpiod_add_lookup_table' [-Werror=implicit-function-declaration]

  271 |         gpiod_add_lookup_table(&pandora_soc_audio_gpios);
      |         ^~~~~~~~~~~~~~~~~~~~~~
arch/arm/mach-omap2/pdata-quirks.c: At top level:
arch/arm/mach-omap2/pdata-quirks.c:259:34: error: storage size of
'pandora_soc_audio_gpios' isn't known
  259 | static struct gpiod_lookup_table pandora_soc_audio_gpios = {
      |                                  ^~~~~~~~~~~~~~~~~~~~~~~

cc1: some warnings being treated as errors
make[3]: *** [scripts/Makefile.build:250:
arch/arm/mach-omap2/pdata-quirks.o] Error 1

steps to reproduce:
---

# tuxmake --runtime podman --target-arch arm --toolchain gcc-13
--kconfig omap2plus_defconfig

Links
---
- https://storage.tuxsuite.com/public/linaro/lkft/builds/2fWG4dRZzA7WgJqyLQ8Rm05WTUo/
- https://qa-reports.linaro.org/lkft/linux-stable-rc-linux-6.1.y/build/v6.1.87-142-gcde450ef0f2f/testrun/23640116/suite/build/test/gcc-13-omap2plus_defconfig/details/

--
Linaro LKFT
https://lkft.linaro.org

Greg,

I'm curious why v6.1.88 is still released nevertheless the reports of the build regression on ARM32.

Thanks,

It would also be interesting to understand why commit 0f4048e1a0c6 ("ASoC:
ti: Convert Pandora ASoC to GPIO descriptors") was necessary. It doesn't immediately look like a bug fix.

Thanks,
Guenter

Because I missed this, I thought I had dropped it already, sorry about that. I'll go do a new release with this commit reverted.

thanks,

greg k-h

Built and booted successfully on RISC-V RV64 (HiFive Unmatched).

On ARCH_BRCMSTB using 32-bit and 64-bit ARM kernels, build tested on BMIPS_GENERIC:

Florian

Hi Greg,

We are observing the same build errors that have already been reported with OMAP GPIO ...

Test results for stable-v6.1:

    10 builds:	4 pass, 6 fail
    10 boots:	10 pass, 0 fail
    38 tests:	38 pass, 0 fail

Linux version: 6.1.88-rc1-gcde450ef0f2f
Boards tested: tegra124-jetson-tk1, tegra20-ventana,

                tegra210-p2371-2180, tegra210-p3450-0000,
                tegra30-cardhu-a04

Builds failed: aarch64+defconfig+jetson, arm+multi_v7

Jon

nvpublic

Hi Greg,

Le 4/23/24 à 23:37, Greg Kroah-Hartman a écrit :

I tested 6.1.88-rc1 (cde450ef0f2f5) on Kalray kvx arch (not upstream yet) and everything looks good!

It ran on real hw (k200, k200lp and k300 boards), on qemu as well as on our internal instruction set simulator (ISS).

Tests were run on several interfaces/drivers (usb, qsfp ethernet, eMMC, PCIe endpoint+RC, SPI, remoteproc, uart, iommu). LTP and uClibc-ng testsuites are also run without any regression.

Everything looks fine to us.

Yann

W dniu 23.04.2024 o 23:37, Greg Kroah-Hartman pisze:

Hello,

Tested on a HP 17-by0001nw laptop with an Intel Kaby Lake CPU and Ubuntu 20.04.

Stack:

- amd64,
- ext4 on top of LVM on top of LUKS on top of mdraid on top of NVMe and SATA drives (the SATA drive in the write-mostly mode).

Tested (lightly):
- suspend to RAM,
- suspend to disk,
- virtual machines in QEMU (both i386 and amd64 guests),

- GPU (Intel HD Graphics 620, with 2 Unigine benchmarks)
- WiFi (Realtek RTL8822BE),
- Bluetooth (Realtek RTL8822BE),

- PCI soundcard (Intel HD Audio),
- USB soundcard (Logitech Pro X),
- webcam.

Filesystems tested very lightly (mounting, listing and opening files):
- NFS,
- exFAT
- NTFS via FUSE

Nitpicks:
- three times, the USB keyboard stopped working during boot or thaw from hibernation:
    [  692.295997] usb 1-3.4.3: device descriptor read/64, error -32
    [  692.568182] usb 1-3.4.3: device descriptor read/64, error -32
    [  693.008193] usb 1-3.4.3: device descriptor read/64, error -32
    [  693.280333] usb 1-3.4.3: device descriptor read/64, error -32
    [  693.552617] usb 1-3.4.3: Device not responding to setup address. [  693.760552] usb 1-3.4.3: Device not responding to setup address. [  693.968383] usb 1-3.4.3: device not accepting address 7, error -71 [...]
    [  698.660224] usb 1-3.4.3: device not accepting address 11, error -71 [  698.660303] usb 1-3.4-port3: unable to enumerate USB device

  It happened later on Linux 6.1.86-rc1 (twice), so I suspect faulty hardware. The keyboard is connected via an external hub.

- Bluetooth: inability to send files from mobile phone to laptop unless the BT session was established beforehand,
    - did not happen after restart, too many variables to blame kernel upgrade.

Greetings,

Mateusz

KernelCI report for stable-rc/linux-6.1.y for this week :-

## stable-rc HEAD for linux-6.1.y:
Date: 2024-04-24
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git/log/?h=cde450ef0f2f55f2c1d63110616bc88f9af5cf38

## Build failures:
arm:
- multi_v7_defconfig (gcc-10) and omap2plus_defconfig (gcc-10)
- Build details :- https://linux.kernelci.org/build/stable-rc/branch/linux-6.1.y/kernel/v6.1.87-142-gcde450ef0f2f/
- Errors Summary
arch/arm/mach-omap2/pdata-quirks.c:271:2: error: implicit declaration of function ‘gpiod_add_lookup_table’ [-Werror=implicit-function-declaration] arch/arm/mach-omap2/pdata-quirks.c:264:3: error: extra brace group at end of initializer
arch/arm/mach-omap2/pdata-quirks.c:262:41: error: ‘GPIO_ACTIVE_HIGH’ undeclared here (not in a function); did you mean ‘ACPI_ACTIVE_HIGH’? arch/arm/mach-omap2/pdata-quirks.c:262:3: error: implicit declaration of function ‘GPIO_LOOKUP’; did you mean ‘IOP_LOOKUP’? [-Werror=implicit-function-declaration] arch/arm/mach-omap2/pdata-quirks.c:261:3: error: ‘struct gpiod_lookup_table’ has no member named ‘table’ arch/arm/mach-omap2/pdata-quirks.c:261:11: error: extra brace group at end of initializer
arch/arm/mach-omap2/pdata-quirks.c:260:3: error: ‘struct gpiod_lookup_table’ has no member named ‘dev_id’ arch/arm/mach-omap2/pdata-quirks.c:259:34: error: storage size of ‘pandora_soc_audio_gpios’ isn’t known arch/arm/mach-omap2/pdata-quirks.c:259:15: error: variable ‘pandora_soc_audio_gpios’ has initializer but incomplete type

## Boot failures:
No **new** boot failures seen for the stable-rc/linux-6.1.y commit head \o/

Thanks,
Shreeya Patel

I'm seeing boot issues with NFS boots on i.MX8MP-EVK - the boot grinds to a halt with

[   20.360083] platform 38330000.blk-ctrl: deferred probe pending
[   20.365958] platform 32f10000.blk-ctrl: deferred probe pending
[   20.371821] platform 32f10108.usb: deferred probe pending
[   20.377240] platform 382f0040.usb-phy: deferred probe pending
[   20.383017] platform 33800000.pcie: deferred probe pending
[   20.388531] platform 32ec0000.blk-ctrl: deferred probe pending

...

38330000.blk-ctrl imx8m-blk-ctrl: failed to get noc entries
32f10000.blk-ctrl imx8mp-blk-ctrl: failed to get noc entries
32f10108.usb platform: supplier 32f10000.blk-ctrl not ready
382f0040.usb-phy platform: supplier 32f10000.blk-ctrl not ready
33800000.pcie platform: supplier 32f10000.blk-ctrl not ready
32ec0000.blk-ctrl imx8m-blk-ctrl: failed to get noc entries

in userspace. A bisect seems to get a bit confused, it lands on 994b8a6164e700277d0360add4 ("ARM: davinci: Drop unused includes") though I do note there are a bunch of PCI commits in stable:

# bad: [cde450ef0f2f55f2c1d63110616bc88f9af5cf38] Linux 6.1.88-rc1
# good: [6741e066ec7633450d3186946035c1f80c4226b8] Linux 6.1.87
git bisect start 'cde450ef0f2f55f2c1d63110616bc88f9af5cf38' '6741e066ec7633450d3186946035c1f80c4226b8' # bad: [cde450ef0f2f55f2c1d63110616bc88f9af5cf38] Linux 6.1.88-rc1
git bisect bad cde450ef0f2f55f2c1d63110616bc88f9af5cf38
# bad: [a355bccd5a9eb683690638e9919179df7346cc54] ASoC: ti: Convert Pandora ASoC to GPIO descriptors git bisect bad a355bccd5a9eb683690638e9919179df7346cc54
# good: [a88f4bc403029938ecf02b9a7c7e399aff38999f] netfilter: nf_tables: Fix potential data-race in __nft_obj_type_get() git bisect good a88f4bc403029938ecf02b9a7c7e399aff38999f
# good: [68ba80017542c03d7cfc945d11c6dcff2960a035] drm: nv04: Fix out of bounds access
git bisect good 68ba80017542c03d7cfc945d11c6dcff2960a035
# good: [df22a0b3b1614738c37d258546b7cc65838fa845] thunderbolt: Log function name of the called quirk git bisect good df22a0b3b1614738c37d258546b7cc65838fa845
# good: [3a11c47c99785089964286bf924ed19f3b158b26] PCI: switchtec: Use normal comment style
git bisect good 3a11c47c99785089964286bf924ed19f3b158b26
# bad: [994b8a6164e700277d0360add4b57d15266164e3] ARM: davinci: Drop unused includes
git bisect bad 994b8a6164e700277d0360add4b57d15266164e3
# good: [fadeaa2b2eb578d5c326332758c7935740be954e] PCI: switchtec: Add support for PCIe Gen5 devices git bisect good fadeaa2b2eb578d5c326332758c7935740be954e

# first bad commit: [994b8a6164e700277d0360add4b57d15266164e3] ARM: davinci: Drop unused includes

Hi!

Cleanups. This code is so old it should not really be touched in stable.

I guess this is some kind of preparation for something we don't have in 6.1?

This is preparation for patches we won't take to 6.1.

This is preparation for patches we won't take to 6.1.

Big rename, and it comes after relevant patches, so unneeded.

Best regards,
Pavel

DENX Software Engineering GmbH,        Managing Director: Erika Unter
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany