Skip to contentSkip to conversation

ARM: dts: imx: Enable PCIe and NVMe on DH i.MX8M Plus DHCOM PDK3

PATCH Applied Marek Vasut 2 participants 2 messages Apr 23, 2024 – Apr 29, 2024

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 ARM: dts: imx: Enable PCIe and NVMe on DH i.MX8M Plus DHCOM PDK3

Enable PCIe/NVMe support on DH i.MX8M Plus DHCOM PDK3. Except for the configuration options which are enabled, add slight adjustment to board u-boot.dtsi, which is necessary as there is currently no driver for the I2C PCIe clock generator. Since the generator is strapped to be always on, it is possible to supplant the generator functionality by fixed-clock.

---
Cc: "NXP i.MX U-Boot Team" <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Tom Rini <[email protected]>
Cc: [email protected]
Cc: [email protected]

---
 arch/arm/dts/imx8mp-dhcom-pdk3-u-boot.dtsi | 12 ++++++++++++
 configs/imx8mp_dhcom_pdk3_defconfig        |  5 +++++
 2 files changed, 17 insertions(+)
arch/arm/dts/imx8mp-dhcom-pdk3-u-boot.dtsi +12 -0
index 040f333c52d..b0b99d51856 100644
@@ -4,3 +4,15 @@
  */
 
 #include "imx8mp-dhcom-u-boot.dtsi"
+
+/ {
+	clk_pcie100: clk-pcie100 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <100000000>;
+	};
+};
+
+&pcie_phy {
+	clocks = <&clk_pcie100>;
+};
configs/imx8mp_dhcom_pdk3_defconfig +5 -0
index a42dc27aff8..019595edda8 100644
@@ -31,6 +31,7 @@ CONFIG_ENV_OFFSET_REDUND=0xFF0000
 CONFIG_IMX_BOOTAUX=y
 CONFIG_SPL_IMX_ROMAPI_LOADADDR=0x48000000
 CONFIG_SYS_LOAD_ADDR=0x50000000
+CONFIG_PCI=y
 CONFIG_DEBUG_UART=y
 CONFIG_ENV_VARS_UBOOT_CONFIG=y
 CONFIG_FIT=y
@@ -104,6 +105,7 @@ CONFIG_CMD_MMC=y
 CONFIG_CMD_BKOPS_ENABLE=y
 CONFIG_CMD_MTD=y
 CONFIG_CMD_PART=y
+CONFIG_CMD_PCI=y
 CONFIG_CMD_READ=y
 CONFIG_CMD_SPI=y
 CONFIG_CMD_USB=y
@@ -218,7 +220,10 @@ CONFIG_DWC_ETH_QOS_IMX=y
 CONFIG_FEC_MXC=y
 CONFIG_RGMII=y
 CONFIG_MII=y
+CONFIG_NVME_PCI=y
+CONFIG_PCIE_DW_IMX=y
 CONFIG_PHY_IMX8MQ_USB=y
+CONFIG_PHY_IMX8M_PCIE=y
 CONFIG_PINCTRL=y
 CONFIG_SPL_PINCTRL=y
 CONFIG_PINCTRL_IMX8M=y
Signature · 1 line
2.43.0
reviewer Applied
#1 lore raw
Quoted 9 lines · Marek Vasut

Enable PCIe/NVMe support on DH i.MX8M Plus DHCOM PDK3. Except for the configuration options which are enabled, add slight adjustment to board u-boot.dtsi, which is necessary as there is currently no driver for the I2C PCIe clock generator. Since the generator is strapped to be always on, it is possible to supplant the generator functionality by fixed-clock.

Applied, thanks.