riscv: dts: starfive: add Milkv Mars board device tree

PATCH Applied Jisheng Zhang 3 participants 14 messages Apr 29, 2024 – Apr 30, 2024

Subsystems (3)

Device tree bindings RISC-V StarFive devicetrees

lore

Share & tools

lore

Jisheng Zhang

author

2024-04-29 00:26 UTC #0 lore raw

v4 cover riscv: dts: starfive: add Milkv Mars board device tree

The Milkv Mars is a development board based on the Starfive JH7110 SoC. The board features:

- JH7110 SoC
- 1/2/4/8 GiB LPDDR4 DRAM
- AXP15060 PMIC
- 40 pin GPIO header
- 3x USB 3.0 host port
- 1x USB 2.0 host port
- 1x M.2 E-Key
- 1x eMMC slot
- 1x MicroSD slot
- 1x QSPI Flash
- 1x 1Gbps Ethernet port
- 1x HDMI port
- 1x 2-lane DSI and 1x 4-lane DSI
- 1x 2-lane CSI

patch1 adds 'cpus' label
patch2 adds "milkv,mars" board dt-binding
patch3 ~ patch4 adopt Krzysztof's suggestions to DT node names patch5 introduces a board common dtsi for visionfive2 and mars patch3 adds the mars board dts file describing the currently supported features:
Namely PMIC, UART, I2C, GPIO, SD card, QSPI Flash, eMMC and Ethernet.

Since v3:
- collect Reviewed-by tag
- rename the common dtsi to jh7110-common.dtsi
- mv cd-gpios and disable-wp into jh7110-common.dtsi
- fix "gmac1-rgmii-rxin-clock: 'clock-frequency' is a required property" warning

Since v2:
- add a common board file which can be used by vf2 and mars

Since v1:
- add two new patches which add "cpus" label and board dt-binding
- adopt Krzysztof's suggestions, thanks

Jisheng Zhang (8):
riscv: dts: starfive: add 'cpus' label to jh7110 and jh7100 soc dtsi
dt-bindings: riscv: starfive: add Milkv Mars board
riscv: dts: starfive: visionfive 2: update sound and codec dt node
name
riscv: dts: starfive: visionfive 2: use cpus label for timebase freq
riscv: dts: starfive: visionfive 2: add tf cd-gpios
riscv: dts: starfive: visionfive 2: add "disable-wp" for tfcard
riscv: dts: starfive: introduce a common board dtsi for jh7110 based
boards
riscv: dts: starfive: add Milkv Mars board device tree

 .../devicetree/bindings/riscv/starfive.yaml   |   1 +
 arch/riscv/boot/dts/starfive/Makefile         |   1 +
 arch/riscv/boot/dts/starfive/jh7100.dtsi      |   2 +-
 .../boot/dts/starfive/jh7110-common.dtsi      | 599 ++++++++++++++++++
 .../boot/dts/starfive/jh7110-milkv-mars.dts   |  30 +
 .../jh7110-starfive-visionfive-2.dtsi         | 584 +----------------
 arch/riscv/boot/dts/starfive/jh7110.dtsi      |   2 +-
 7 files changed, 634 insertions(+), 585 deletions(-)
 create mode 100644 arch/riscv/boot/dts/starfive/jh7110-common.dtsi
 create mode 100644 arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts

Signature · 1 line

2.43.0

Jisheng Zhang

author

2024-04-29 00:26 UTC #1 lore raw

PATCH v4 1/8 riscv: dts: starfive: add 'cpus' label to jh7110 and jh7100 soc dtsi

Add the 'cpus' label so that we can reference it in board dts files.

Signed-off-by Jisheng Zhang <[email protected]>

Reviewed-by Emil Renner Berthing <[email protected]>

---
 arch/riscv/boot/dts/starfive/jh7100.dtsi | 2 +-
 arch/riscv/boot/dts/starfive/jh7110.dtsi | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)

arch/riscv/boot/dts/starfive/jh7100.dtsi +1 -1

index 9a2e9583af88..7de0732b8eab 100644
@@ -13,7 +13,7 @@ / {
 	#address-cells = <2>;
 	#size-cells = <2>;
 
-	cpus {
+	cpus: cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;

arch/riscv/boot/dts/starfive/jh7110.dtsi +1 -1

index 4a5708f7fcf7..18047195c600 100644
@@ -15,7 +15,7 @@ / {
 	#address-cells = <2>;
 	#size-cells = <2>;
 
-	cpus {
+	cpus: cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;

Signature · 1 line

2.43.0

Jisheng Zhang

author

2024-04-29 00:26 UTC #2 lore raw

PATCH v4 2/8 dt-bindings: riscv: starfive: add Milkv Mars board

In reply to Jisheng Zhang

Add device tree bindings for the Milkv Mars board which is equipped with StarFive JH7110 SoC.

Signed-off-by Jisheng Zhang <[email protected]>

Acked-by Krzysztof Kozlowski <[email protected]>

Reviewed-by Emil Renner Berthing <[email protected]>

---
 Documentation/devicetree/bindings/riscv/starfive.yaml | 1 +
 1 file changed, 1 insertion(+)

Documentation/devicetree/bindings/riscv/starfive.yaml +1 -0

index cc4d92f0a1bf..b672f8521949 100644
@@ -26,6 +26,7 @@ properties:
 
       - items:
           - enum:
+              - milkv,mars
               - starfive,visionfive-2-v1.2a
               - starfive,visionfive-2-v1.3b
           - const: starfive,jh7110

Signature · 1 line

2.43.0

Jisheng Zhang

author

2024-04-29 00:26 UTC #3 lore raw

PATCH v4 3/8 riscv: dts: starfive: visionfive 2: update sound and codec dt node name

In reply to Jisheng Zhang

Use "audio-codec" as the codec dt node name, and "sound" as the simple audio card dt name.

Signed-off-by Jisheng Zhang <[email protected]>

Reviewed-by Emil Renner Berthing <[email protected]>

---
 .../riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi +2 -2

index ccd0ce55aa53..50955cc45658 100644
@@ -41,12 +41,12 @@ gpio-restart {
 		priority = <224>;
 	};
 
-	pwmdac_codec: pwmdac-codec {
+	pwmdac_codec: audio-codec {
 		compatible = "linux,spdif-dit";
 		#sound-dai-cells = <0>;
 	};
 
-	sound-pwmdac {
+	sound {
 		compatible = "simple-audio-card";
 		simple-audio-card,name = "StarFive-PWMDAC-Sound-Card";
 		#address-cells = <1>;

Signature · 1 line

2.43.0

Jisheng Zhang

author

2024-04-29 00:26 UTC #4 lore raw

PATCH v4 4/8 riscv: dts: starfive: visionfive 2: use cpus label for timebase freq

In reply to Jisheng Zhang

As pointed out by Krzysztof "Board should not bring new CPU nodes. Override by label instead."

Signed-off-by Jisheng Zhang <[email protected]>

Reviewed-by Emil Renner Berthing <[email protected]>

---
 .../boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi   | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi +4 -4

index 50955cc45658..910c07bd4af9 100644
@@ -26,10 +26,6 @@ chosen {
 		stdout-path = "serial0:115200n8";
 	};
 
-	cpus {
-		timebase-frequency = <4000000>;
-	};
-
 	memory@40000000 {
 		device_type = "memory";
 		reg = <0x0 0x40000000 0x1 0x0>;

@@ -69,6 +65,10 @@ codec {
 	};
 };
 
+&cpus {
+	timebase-frequency = <4000000>;
+};
+
 &dvp_clk {
 	clock-frequency = <74250000>;
 };

Signature · 1 line

2.43.0

Jisheng Zhang

author

2024-04-29 00:27 UTC #5 lore raw

PATCH v4 5/8 riscv: dts: starfive: visionfive 2: add tf cd-gpios

In reply to Jisheng Zhang

Per VisionFive 2 1.2B, and 1.3A boards' SCH, GPIO 41 is used as card detect. So add "cd-gpios" property for this.

Signed-off-by Jisheng Zhang <[email protected]>

---
 arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi +1 -1

index 910c07bd4af9..b6030d63459d 100644
@@ -303,7 +303,7 @@ &mmc1 {
 	bus-width = <4>;
 	no-sdio;
 	no-mmc;
-	broken-cd;
+	cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
 	cap-sd-highspeed;
 	post-power-on-delay-ms = <200>;
 	pinctrl-names = "default";

Signature · 1 line

2.43.0

Emil Renner Berthing

Reviewed-by on v4 5/8

2024-04-29 13:46 UTC #6 lore raw

Re: [PATCH v4 5/8] riscv: dts: starfive: visionfive 2: add tf cd-gpios

Quoted 13 lines · Jisheng Zhang

Per VisionFive 2 1.2B, and 1.3A boards' SCH, GPIO 41 is used as card detect. So add "cd-gpios" property for this.
Signed-off-by Jisheng Zhang <[email protected]>
---
 arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi +0 -0
index 910c07bd4af9..b6030d63459d 100644

arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi &mmc1 { · line 306

Quoted 5 lines

arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi +1 -1
@@ -303,7 +303,7 @@ &mmc1 {
 	bus-width = <4>;
 	no-sdio;
 	no-mmc;
-	broken-cd;
+	cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;

nit if you need to respin this anyway: i know the properties are already not sorted, but i'd prefer to not add more properties out of order.

In any case

Reviewed-by Emil Renner Berthing <[email protected]>

Quoted 6 lines

arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi +0 -1
 	cap-sd-highspeed;
 	post-power-on-delay-ms = <200>;
 	pinctrl-names = "default";
--
2.43.0

Jisheng Zhang

author

2024-04-29 00:27 UTC #7 lore raw

PATCH v4 6/8 riscv: dts: starfive: visionfive 2: add "disable-wp" for tfcard

In reply to Jisheng Zhang

No physical write-protect line is present, so setting "disable-wp".

Signed-off-by Jisheng Zhang <[email protected]>

---
 arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi | 1 +
 1 file changed, 1 insertion(+)

arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi +1 -0

index b6030d63459d..e19f26628054 100644
@@ -304,6 +304,7 @@ &mmc1 {
 	no-sdio;
 	no-mmc;
 	cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
+	disable-wp;
 	cap-sd-highspeed;
 	post-power-on-delay-ms = <200>;
 	pinctrl-names = "default";

Signature · 1 line

2.43.0

Emil Renner Berthing

Reviewed-by on v4 6/8

2024-04-29 13:47 UTC #8 lore raw

Re: [PATCH v4 6/8] riscv: dts: starfive: visionfive 2: add "disable-wp" for tfcard

Quoted 12 lines · Jisheng Zhang

No physical write-protect line is present, so setting "disable-wp".
Signed-off-by Jisheng Zhang <[email protected]>
---
 arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi | 1 +
 1 file changed, 1 insertion(+)
arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi +0 -0
index b6030d63459d..e19f26628054 100644

arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi &mmc1 { · line 307

Quoted 4 lines

arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi +1 -0
@@ -304,6 +304,7 @@ &mmc1 {
 	no-sdio;
 	no-mmc;
 	cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
+	disable-wp;

Same nit as patch 5/6, but in any case:

Reviewed-by Emil Renner Berthing <[email protected]>

Quoted 6 lines

arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi +0 -1
 	cap-sd-highspeed;
 	post-power-on-delay-ms = <200>;
 	pinctrl-names = "default";
--
2.43.0

Jisheng Zhang

author

2024-04-29 00:27 UTC #9 lore raw

PATCH v4 7/8 riscv: dts: starfive: introduce a common board dtsi for jh7110 based boards

In reply to Jisheng Zhang

This is to prepare for Milkv Mars board dts support in the following patch. Let's factored out common part into .dtsi.

Signed-off-by Jisheng Zhang <[email protected]>

---
 .../boot/dts/starfive/jh7110-common.dtsi      | 599 ++++++++++++++++++
 .../jh7110-starfive-visionfive-2.dtsi         | 585 +----------------
 2 files changed, 600 insertions(+), 584 deletions(-)
 create mode 100644 arch/riscv/boot/dts/starfive/jh7110-common.dtsi

arch/riscv/boot/dts/starfive/jh7110-common.dtsi new file +599 -0

new file mode 100644
index 000000000000..8ff6ea64f048
@@ -0,0 +1,599 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+/*
+ * Copyright (C) 2022 StarFive Technology Co., Ltd.
+ * Copyright (C) 2022 Emil Renner Berthing <[email protected]>
+ */
+
+/dts-v1/;
+#include "jh7110.dtsi"
+#include "jh7110-pinfunc.h"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	aliases {
+		ethernet0 = &gmac0;
+		i2c0 = &i2c0;
+		i2c2 = &i2c2;
+		i2c5 = &i2c5;
+		i2c6 = &i2c6;
+		mmc0 = &mmc0;
+		mmc1 = &mmc1;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x0 0x40000000 0x1 0x0>;
+	};
+
+	gpio-restart {
+		compatible = "gpio-restart";
+		gpios = <&sysgpio 35 GPIO_ACTIVE_HIGH>;
+		priority = <224>;
+	};
+
+	pwmdac_codec: audio-codec {
+		compatible = "linux,spdif-dit";
+		#sound-dai-cells = <0>;
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "StarFive-PWMDAC-Sound-Card";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		simple-audio-card,dai-link@0 {
+			reg = <0>;
+			format = "left_j";
+			bitclock-master = <&sndcpu0>;
+			frame-master = <&sndcpu0>;
+
+			sndcpu0: cpu {
+				sound-dai = <&pwmdac>;
+			};
+
+			codec {
+				sound-dai = <&pwmdac_codec>;
+			};
+		};
+	};
+};
+
+&cpus {
+	timebase-frequency = <4000000>;
+};
+
+&dvp_clk {
+	clock-frequency = <74250000>;
+};
+
+&gmac0_rgmii_rxin {
+	clock-frequency = <125000000>;
+};
+
+&gmac0_rmii_refin {
+	clock-frequency = <50000000>;
+};
+
+&gmac1_rgmii_rxin {
+	clock-frequency = <125000000>;
+};
+
+&gmac1_rmii_refin {
+	clock-frequency = <50000000>;
+};
+
+&hdmitx0_pixelclk {
+	clock-frequency = <297000000>;
+};
+
+&i2srx_bclk_ext {
+	clock-frequency = <12288000>;
+};
+
+&i2srx_lrck_ext {
+	clock-frequency = <192000>;
+};
+
+&i2stx_bclk_ext {
+	clock-frequency = <12288000>;
+};
+
+&i2stx_lrck_ext {
+	clock-frequency = <192000>;
+};
+
+&mclk_ext {
+	clock-frequency = <12288000>;
+};
+
+&osc {
+	clock-frequency = <24000000>;
+};
+
+&rtc_osc {
+	clock-frequency = <32768>;
+};
+
+&tdm_ext {
+	clock-frequency = <49152000>;
+};
+
+&camss {
+	assigned-clocks = <&ispcrg JH7110_ISPCLK_DOM4_APB_FUNC>,
+			  <&ispcrg JH7110_ISPCLK_MIPI_RX0_PXL>;
+	assigned-clock-rates = <49500000>, <198000000>;
+	status = "okay";
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+		};
+
+		port@1 {
+			reg = <1>;
+
+			camss_from_csi2rx: endpoint {
+				remote-endpoint = <&csi2rx_to_camss>;
+			};
+		};
+	};
+};
+
+&csi2rx {
+	assigned-clocks = <&ispcrg JH7110_ISPCLK_VIN_SYS>;
+	assigned-clock-rates = <297000000>;
+	status = "okay";
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			/* remote MIPI sensor endpoint */
+		};
+
+		port@1 {
+			reg = <1>;
+
+			csi2rx_to_camss: endpoint {
+				remote-endpoint = <&camss_from_csi2rx>;
+			};
+		};
+	};
+};
+
+&gmac0 {
+	phy-handle = <&phy0>;
+	phy-mode = "rgmii-id";
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+
+		phy0: ethernet-phy@0 {
+			reg = <0>;
+		};
+	};
+};
+
+&i2c0 {
+	clock-frequency = <100000>;
+	i2c-sda-hold-time-ns = <300>;
+	i2c-sda-falling-time-ns = <510>;
+	i2c-scl-falling-time-ns = <510>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	status = "okay";
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	i2c-sda-hold-time-ns = <300>;
+	i2c-sda-falling-time-ns = <510>;
+	i2c-scl-falling-time-ns = <510>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins>;
+	status = "okay";
+};
+
+&i2c5 {
+	clock-frequency = <100000>;
+	i2c-sda-hold-time-ns = <300>;
+	i2c-sda-falling-time-ns = <510>;
+	i2c-scl-falling-time-ns = <510>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c5_pins>;
+	status = "okay";
+
+	axp15060: pmic@36 {
+		compatible = "x-powers,axp15060";
+		reg = <0x36>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+
+		regulators {
+			vcc_3v3: dcdc1 {
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc_3v3";
+			};
+
+			vdd_cpu: dcdc2 {
+				regulator-always-on;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1540000>;
+				regulator-name = "vdd-cpu";
+			};
+
+			emmc_vdd: aldo4 {
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "emmc_vdd";
+			};
+		};
+	};
+};
+
+&i2c6 {
+	clock-frequency = <100000>;
+	i2c-sda-hold-time-ns = <300>;
+	i2c-sda-falling-time-ns = <510>;
+	i2c-scl-falling-time-ns = <510>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c6_pins>;
+	status = "okay";
+};
+
+&mmc0 {
+	max-frequency = <100000000>;
+	assigned-clocks = <&syscrg JH7110_SYSCLK_SDIO0_SDCARD>;
+	assigned-clock-rates = <50000000>;
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	cap-mmc-hw-reset;
+	post-power-on-delay-ms = <200>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&emmc_vdd>;
+	status = "okay";
+};
+
+&mmc1 {
+	max-frequency = <100000000>;
+	assigned-clocks = <&syscrg JH7110_SYSCLK_SDIO1_SDCARD>;
+	assigned-clock-rates = <50000000>;
+	bus-width = <4>;
+	no-sdio;
+	no-mmc;
+	cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	cap-sd-highspeed;
+	post-power-on-delay-ms = <200>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	status = "okay";
+};
+
+&pwmdac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwmdac_pins>;
+	status = "okay";
+};
+
+&qspi {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	nor_flash: flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		cdns,read-delay = <5>;
+		spi-max-frequency = <12000000>;
+		cdns,tshsl-ns = <1>;
+		cdns,tsd2d-ns = <1>;
+		cdns,tchsh-ns = <1>;
+		cdns,tslch-ns = <1>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			spl@0 {
+				reg = <0x0 0x80000>;
+			};
+			uboot-env@f0000 {
+				reg = <0xf0000 0x10000>;
+			};
+			uboot@100000 {
+				reg = <0x100000 0x400000>;
+			};
+			reserved-data@600000 {
+				reg = <0x600000 0xa00000>;
+			};
+		};
+	};
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm_pins>;
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins>;
+	status = "okay";
+
+	spi_dev0: spi@0 {
+		compatible = "rohm,dh2228fv";
+		reg = <0>;
+		spi-max-frequency = <10000000>;
+	};
+};
+
+&sysgpio {
+	i2c0_pins: i2c0-0 {
+		i2c-pins {
+			pinmux = <GPIOMUX(57, GPOUT_LOW,
+					      GPOEN_SYS_I2C0_CLK,
+					      GPI_SYS_I2C0_CLK)>,
+				 <GPIOMUX(58, GPOUT_LOW,
+					      GPOEN_SYS_I2C0_DATA,
+					      GPI_SYS_I2C0_DATA)>;
+			bias-disable; /* external pull-up */
+			input-enable;
+			input-schmitt-enable;
+		};
+	};
+
+	i2c2_pins: i2c2-0 {
+		i2c-pins {
+			pinmux = <GPIOMUX(3, GPOUT_LOW,
+					     GPOEN_SYS_I2C2_CLK,
+					     GPI_SYS_I2C2_CLK)>,
+				 <GPIOMUX(2, GPOUT_LOW,
+					     GPOEN_SYS_I2C2_DATA,
+					     GPI_SYS_I2C2_DATA)>;
+			bias-disable; /* external pull-up */
+			input-enable;
+			input-schmitt-enable;
+		};
+	};
+
+	i2c5_pins: i2c5-0 {
+		i2c-pins {
+			pinmux = <GPIOMUX(19, GPOUT_LOW,
+					      GPOEN_SYS_I2C5_CLK,
+					      GPI_SYS_I2C5_CLK)>,
+				 <GPIOMUX(20, GPOUT_LOW,
+					      GPOEN_SYS_I2C5_DATA,
+					      GPI_SYS_I2C5_DATA)>;
+			bias-disable; /* external pull-up */
+			input-enable;
+			input-schmitt-enable;
+		};
+	};
+
+	i2c6_pins: i2c6-0 {
+		i2c-pins {
+			pinmux = <GPIOMUX(16, GPOUT_LOW,
+					      GPOEN_SYS_I2C6_CLK,
+					      GPI_SYS_I2C6_CLK)>,
+				 <GPIOMUX(17, GPOUT_LOW,
+					      GPOEN_SYS_I2C6_DATA,
+					      GPI_SYS_I2C6_DATA)>;
+			bias-disable; /* external pull-up */
+			input-enable;
+			input-schmitt-enable;
+		};
+	};
+
+	mmc0_pins: mmc0-0 {
+		 rst-pins {
+			pinmux = <GPIOMUX(62, GPOUT_SYS_SDIO0_RST,
+					      GPOEN_ENABLE,
+					      GPI_NONE)>;
+			bias-pull-up;
+			drive-strength = <12>;
+			input-disable;
+			input-schmitt-disable;
+			slew-rate = <0>;
+		};
+
+		mmc-pins {
+			pinmux = <PINMUX(64, 0)>,
+				 <PINMUX(65, 0)>,
+				 <PINMUX(66, 0)>,
+				 <PINMUX(67, 0)>,
+				 <PINMUX(68, 0)>,
+				 <PINMUX(69, 0)>,
+				 <PINMUX(70, 0)>,
+				 <PINMUX(71, 0)>,
+				 <PINMUX(72, 0)>,
+				 <PINMUX(73, 0)>;
+			bias-pull-up;
+			drive-strength = <12>;
+			input-enable;
+		};
+	};
+
+	mmc1_pins: mmc1-0 {
+		clk-pins {
+			pinmux = <GPIOMUX(10, GPOUT_SYS_SDIO1_CLK,
+					      GPOEN_ENABLE,
+					      GPI_NONE)>;
+			bias-pull-up;
+			drive-strength = <12>;
+			input-disable;
+			input-schmitt-disable;
+			slew-rate = <0>;
+		};
+
+		mmc-pins {
+			pinmux = <GPIOMUX(9, GPOUT_SYS_SDIO1_CMD,
+					     GPOEN_SYS_SDIO1_CMD,
+					     GPI_SYS_SDIO1_CMD)>,
+				 <GPIOMUX(11, GPOUT_SYS_SDIO1_DATA0,
+					      GPOEN_SYS_SDIO1_DATA0,
+					      GPI_SYS_SDIO1_DATA0)>,
+				 <GPIOMUX(12, GPOUT_SYS_SDIO1_DATA1,
+					      GPOEN_SYS_SDIO1_DATA1,
+					      GPI_SYS_SDIO1_DATA1)>,
+				 <GPIOMUX(7, GPOUT_SYS_SDIO1_DATA2,
+					     GPOEN_SYS_SDIO1_DATA2,
+					     GPI_SYS_SDIO1_DATA2)>,
+				 <GPIOMUX(8, GPOUT_SYS_SDIO1_DATA3,
+					     GPOEN_SYS_SDIO1_DATA3,
+					     GPI_SYS_SDIO1_DATA3)>;
+			bias-pull-up;
+			drive-strength = <12>;
+			input-enable;
+			input-schmitt-enable;
+			slew-rate = <0>;
+		};
+	};
+
+	pwmdac_pins: pwmdac-0 {
+		pwmdac-pins {
+			pinmux = <GPIOMUX(33, GPOUT_SYS_PWMDAC_LEFT,
+					      GPOEN_ENABLE,
+					      GPI_NONE)>,
+				 <GPIOMUX(34, GPOUT_SYS_PWMDAC_RIGHT,
+					      GPOEN_ENABLE,
+					      GPI_NONE)>;
+			bias-disable;
+			drive-strength = <2>;
+			input-disable;
+			input-schmitt-disable;
+			slew-rate = <0>;
+		};
+	};
+
+	pwm_pins: pwm-0 {
+		pwm-pins {
+			pinmux = <GPIOMUX(46, GPOUT_SYS_PWM_CHANNEL0,
+					      GPOEN_SYS_PWM0_CHANNEL0,
+					      GPI_NONE)>,
+				 <GPIOMUX(59, GPOUT_SYS_PWM_CHANNEL1,
+					      GPOEN_SYS_PWM0_CHANNEL1,
+					      GPI_NONE)>;
+			bias-disable;
+			drive-strength = <12>;
+			input-disable;
+			input-schmitt-disable;
+			slew-rate = <0>;
+		};
+	};
+
+	spi0_pins: spi0-0 {
+		mosi-pins {
+			pinmux = <GPIOMUX(52, GPOUT_SYS_SPI0_TXD,
+					      GPOEN_ENABLE,
+					      GPI_NONE)>;
+			bias-disable;
+			input-disable;
+			input-schmitt-disable;
+		};
+
+		miso-pins {
+			pinmux = <GPIOMUX(53, GPOUT_LOW,
+					      GPOEN_DISABLE,
+					      GPI_SYS_SPI0_RXD)>;
+			bias-pull-up;
+			input-enable;
+			input-schmitt-enable;
+		};
+
+		sck-pins {
+			pinmux = <GPIOMUX(48, GPOUT_SYS_SPI0_CLK,
+					      GPOEN_ENABLE,
+					      GPI_SYS_SPI0_CLK)>;
+			bias-disable;
+			input-disable;
+			input-schmitt-disable;
+		};
+
+		ss-pins {
+			pinmux = <GPIOMUX(49, GPOUT_SYS_SPI0_FSS,
+					      GPOEN_ENABLE,
+					      GPI_SYS_SPI0_FSS)>;
+			bias-disable;
+			input-disable;
+			input-schmitt-disable;
+		};
+	};
+
+	uart0_pins: uart0-0 {
+		tx-pins {
+			pinmux = <GPIOMUX(5, GPOUT_SYS_UART0_TX,
+					     GPOEN_ENABLE,
+					     GPI_NONE)>;
+			bias-disable;
+			drive-strength = <12>;
+			input-disable;
+			input-schmitt-disable;
+			slew-rate = <0>;
+		};
+
+		rx-pins {
+			pinmux = <GPIOMUX(6, GPOUT_LOW,
+					     GPOEN_DISABLE,
+					     GPI_SYS_UART0_RX)>;
+			bias-disable; /* external pull-up */
+			drive-strength = <2>;
+			input-enable;
+			input-schmitt-enable;
+			slew-rate = <0>;
+		};
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins>;
+	status = "okay";
+};
+
+&usb0 {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&U74_1 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&U74_2 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&U74_3 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&U74_4 {
+	cpu-supply = <&vdd_cpu>;
+};

arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi +1 ~~-584~~

601 lines not on this page · raw message

Signature · 1 line

2.43.0

Emil Renner Berthing

Reviewed-by on v4 7/8

2024-04-29 13:51 UTC #10 lore raw

Re: [PATCH v4 7/8] riscv: dts: starfive: introduce a common board dtsi for jh7110 based boards

Quoted 2 lines · Jisheng Zhang

This is to prepare for Milkv Mars board dts support in the following patch. Let's factored out common part into .dtsi.

Maybe something like:

"Many boards using the StarFive JH7110 SoC share a lot of their design with the first VisionFive 2 boards. Let's factor out the common parts in preparation for adding support for the Milk-V Mars board."

In any case:

Reviewed-by Emil Renner Berthing <[email protected]>

Quoted 1,223 lines

Signed-off-by Jisheng Zhang <[email protected]>

---
 .../boot/dts/starfive/jh7110-common.dtsi      | 599 ++++++++++++++++++
 .../jh7110-starfive-visionfive-2.dtsi         | 585 +----------------
 2 files changed, 600 insertions(+), 584 deletions(-)
 create mode 100644 arch/riscv/boot/dts/starfive/jh7110-common.dtsi

arch/riscv/boot/dts/starfive/jh7110-common.dtsi new file +599 -0

new file mode 100644
index 000000000000..8ff6ea64f048
@@ -0,0 +1,599 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+/*
+ * Copyright (C) 2022 StarFive Technology Co., Ltd.
+ * Copyright (C) 2022 Emil Renner Berthing <[email protected]>
+ */
+
+/dts-v1/;
+#include "jh7110.dtsi"
+#include "jh7110-pinfunc.h"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	aliases {
+		ethernet0 = &gmac0;
+		i2c0 = &i2c0;
+		i2c2 = &i2c2;
+		i2c5 = &i2c5;
+		i2c6 = &i2c6;
+		mmc0 = &mmc0;
+		mmc1 = &mmc1;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x0 0x40000000 0x1 0x0>;
+	};
+
+	gpio-restart {
+		compatible = "gpio-restart";
+		gpios = <&sysgpio 35 GPIO_ACTIVE_HIGH>;
+		priority = <224>;
+	};
+
+	pwmdac_codec: audio-codec {
+		compatible = "linux,spdif-dit";
+		#sound-dai-cells = <0>;
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "StarFive-PWMDAC-Sound-Card";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		simple-audio-card,dai-link@0 {
+			reg = <0>;
+			format = "left_j";
+			bitclock-master = <&sndcpu0>;
+			frame-master = <&sndcpu0>;
+
+			sndcpu0: cpu {
+				sound-dai = <&pwmdac>;
+			};
+
+			codec {
+				sound-dai = <&pwmdac_codec>;
+			};
+		};
+	};
+};
+
+&cpus {
+	timebase-frequency = <4000000>;
+};
+
+&dvp_clk {
+	clock-frequency = <74250000>;
+};
+
+&gmac0_rgmii_rxin {
+	clock-frequency = <125000000>;
+};
+
+&gmac0_rmii_refin {
+	clock-frequency = <50000000>;
+};
+
+&gmac1_rgmii_rxin {
+	clock-frequency = <125000000>;
+};
+
+&gmac1_rmii_refin {
+	clock-frequency = <50000000>;
+};
+
+&hdmitx0_pixelclk {
+	clock-frequency = <297000000>;
+};
+
+&i2srx_bclk_ext {
+	clock-frequency = <12288000>;
+};
+
+&i2srx_lrck_ext {
+	clock-frequency = <192000>;
+};
+
+&i2stx_bclk_ext {
+	clock-frequency = <12288000>;
+};
+
+&i2stx_lrck_ext {
+	clock-frequency = <192000>;
+};
+
+&mclk_ext {
+	clock-frequency = <12288000>;
+};
+
+&osc {
+	clock-frequency = <24000000>;
+};
+
+&rtc_osc {
+	clock-frequency = <32768>;
+};
+
+&tdm_ext {
+	clock-frequency = <49152000>;
+};
+
+&camss {
+	assigned-clocks = <&ispcrg JH7110_ISPCLK_DOM4_APB_FUNC>,
+			  <&ispcrg JH7110_ISPCLK_MIPI_RX0_PXL>;
+	assigned-clock-rates = <49500000>, <198000000>;
+	status = "okay";
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+		};
+
+		port@1 {
+			reg = <1>;
+
+			camss_from_csi2rx: endpoint {
+				remote-endpoint = <&csi2rx_to_camss>;
+			};
+		};
+	};
+};
+
+&csi2rx {
+	assigned-clocks = <&ispcrg JH7110_ISPCLK_VIN_SYS>;
+	assigned-clock-rates = <297000000>;
+	status = "okay";
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			/* remote MIPI sensor endpoint */
+		};
+
+		port@1 {
+			reg = <1>;
+
+			csi2rx_to_camss: endpoint {
+				remote-endpoint = <&camss_from_csi2rx>;
+			};
+		};
+	};
+};
+
+&gmac0 {
+	phy-handle = <&phy0>;
+	phy-mode = "rgmii-id";
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+
+		phy0: ethernet-phy@0 {
+			reg = <0>;
+		};
+	};
+};
+
+&i2c0 {
+	clock-frequency = <100000>;
+	i2c-sda-hold-time-ns = <300>;
+	i2c-sda-falling-time-ns = <510>;
+	i2c-scl-falling-time-ns = <510>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	status = "okay";
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	i2c-sda-hold-time-ns = <300>;
+	i2c-sda-falling-time-ns = <510>;
+	i2c-scl-falling-time-ns = <510>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins>;
+	status = "okay";
+};
+
+&i2c5 {
+	clock-frequency = <100000>;
+	i2c-sda-hold-time-ns = <300>;
+	i2c-sda-falling-time-ns = <510>;
+	i2c-scl-falling-time-ns = <510>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c5_pins>;
+	status = "okay";
+
+	axp15060: pmic@36 {
+		compatible = "x-powers,axp15060";
+		reg = <0x36>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+
+		regulators {
+			vcc_3v3: dcdc1 {
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc_3v3";
+			};
+
+			vdd_cpu: dcdc2 {
+				regulator-always-on;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1540000>;
+				regulator-name = "vdd-cpu";
+			};
+
+			emmc_vdd: aldo4 {
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "emmc_vdd";
+			};
+		};
+	};
+};
+
+&i2c6 {
+	clock-frequency = <100000>;
+	i2c-sda-hold-time-ns = <300>;
+	i2c-sda-falling-time-ns = <510>;
+	i2c-scl-falling-time-ns = <510>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c6_pins>;
+	status = "okay";
+};
+
+&mmc0 {
+	max-frequency = <100000000>;
+	assigned-clocks = <&syscrg JH7110_SYSCLK_SDIO0_SDCARD>;
+	assigned-clock-rates = <50000000>;
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	cap-mmc-hw-reset;
+	post-power-on-delay-ms = <200>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&emmc_vdd>;
+	status = "okay";
+};
+
+&mmc1 {
+	max-frequency = <100000000>;
+	assigned-clocks = <&syscrg JH7110_SYSCLK_SDIO1_SDCARD>;
+	assigned-clock-rates = <50000000>;
+	bus-width = <4>;
+	no-sdio;
+	no-mmc;
+	cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	cap-sd-highspeed;
+	post-power-on-delay-ms = <200>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	status = "okay";
+};
+
+&pwmdac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwmdac_pins>;
+	status = "okay";
+};
+
+&qspi {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	nor_flash: flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		cdns,read-delay = <5>;
+		spi-max-frequency = <12000000>;
+		cdns,tshsl-ns = <1>;
+		cdns,tsd2d-ns = <1>;
+		cdns,tchsh-ns = <1>;
+		cdns,tslch-ns = <1>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			spl@0 {
+				reg = <0x0 0x80000>;
+			};
+			uboot-env@f0000 {
+				reg = <0xf0000 0x10000>;
+			};
+			uboot@100000 {
+				reg = <0x100000 0x400000>;
+			};
+			reserved-data@600000 {
+				reg = <0x600000 0xa00000>;
+			};
+		};
+	};
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm_pins>;
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins>;
+	status = "okay";
+
+	spi_dev0: spi@0 {
+		compatible = "rohm,dh2228fv";
+		reg = <0>;
+		spi-max-frequency = <10000000>;
+	};
+};
+
+&sysgpio {
+	i2c0_pins: i2c0-0 {
+		i2c-pins {
+			pinmux = <GPIOMUX(57, GPOUT_LOW,
+					      GPOEN_SYS_I2C0_CLK,
+					      GPI_SYS_I2C0_CLK)>,
+				 <GPIOMUX(58, GPOUT_LOW,
+					      GPOEN_SYS_I2C0_DATA,
+					      GPI_SYS_I2C0_DATA)>;
+			bias-disable; /* external pull-up */
+			input-enable;
+			input-schmitt-enable;
+		};
+	};
+
+	i2c2_pins: i2c2-0 {
+		i2c-pins {
+			pinmux = <GPIOMUX(3, GPOUT_LOW,
+					     GPOEN_SYS_I2C2_CLK,
+					     GPI_SYS_I2C2_CLK)>,
+				 <GPIOMUX(2, GPOUT_LOW,
+					     GPOEN_SYS_I2C2_DATA,
+					     GPI_SYS_I2C2_DATA)>;
+			bias-disable; /* external pull-up */
+			input-enable;
+			input-schmitt-enable;
+		};
+	};
+
+	i2c5_pins: i2c5-0 {
+		i2c-pins {
+			pinmux = <GPIOMUX(19, GPOUT_LOW,
+					      GPOEN_SYS_I2C5_CLK,
+					      GPI_SYS_I2C5_CLK)>,
+				 <GPIOMUX(20, GPOUT_LOW,
+					      GPOEN_SYS_I2C5_DATA,
+					      GPI_SYS_I2C5_DATA)>;
+			bias-disable; /* external pull-up */
+			input-enable;
+			input-schmitt-enable;
+		};
+	};
+
+	i2c6_pins: i2c6-0 {
+		i2c-pins {
+			pinmux = <GPIOMUX(16, GPOUT_LOW,
+					      GPOEN_SYS_I2C6_CLK,
+					      GPI_SYS_I2C6_CLK)>,
+				 <GPIOMUX(17, GPOUT_LOW,
+					      GPOEN_SYS_I2C6_DATA,
+					      GPI_SYS_I2C6_DATA)>;
+			bias-disable; /* external pull-up */
+			input-enable;
+			input-schmitt-enable;
+		};
+	};
+
+	mmc0_pins: mmc0-0 {
+		 rst-pins {
+			pinmux = <GPIOMUX(62, GPOUT_SYS_SDIO0_RST,
+					      GPOEN_ENABLE,
+					      GPI_NONE)>;
+			bias-pull-up;
+			drive-strength = <12>;
+			input-disable;
+			input-schmitt-disable;
+			slew-rate = <0>;
+		};
+
+		mmc-pins {
+			pinmux = <PINMUX(64, 0)>,
+				 <PINMUX(65, 0)>,
+				 <PINMUX(66, 0)>,
+				 <PINMUX(67, 0)>,
+				 <PINMUX(68, 0)>,
+				 <PINMUX(69, 0)>,
+				 <PINMUX(70, 0)>,
+				 <PINMUX(71, 0)>,
+				 <PINMUX(72, 0)>,
+				 <PINMUX(73, 0)>;
+			bias-pull-up;
+			drive-strength = <12>;
+			input-enable;
+		};
+	};
+
+	mmc1_pins: mmc1-0 {
+		clk-pins {
+			pinmux = <GPIOMUX(10, GPOUT_SYS_SDIO1_CLK,
+					      GPOEN_ENABLE,
+					      GPI_NONE)>;
+			bias-pull-up;
+			drive-strength = <12>;
+			input-disable;
+			input-schmitt-disable;
+			slew-rate = <0>;
+		};
+
+		mmc-pins {
+			pinmux = <GPIOMUX(9, GPOUT_SYS_SDIO1_CMD,
+					     GPOEN_SYS_SDIO1_CMD,
+					     GPI_SYS_SDIO1_CMD)>,
+				 <GPIOMUX(11, GPOUT_SYS_SDIO1_DATA0,
+					      GPOEN_SYS_SDIO1_DATA0,
+					      GPI_SYS_SDIO1_DATA0)>,
+				 <GPIOMUX(12, GPOUT_SYS_SDIO1_DATA1,
+					      GPOEN_SYS_SDIO1_DATA1,
+					      GPI_SYS_SDIO1_DATA1)>,
+				 <GPIOMUX(7, GPOUT_SYS_SDIO1_DATA2,
+					     GPOEN_SYS_SDIO1_DATA2,
+					     GPI_SYS_SDIO1_DATA2)>,
+				 <GPIOMUX(8, GPOUT_SYS_SDIO1_DATA3,
+					     GPOEN_SYS_SDIO1_DATA3,
+					     GPI_SYS_SDIO1_DATA3)>;
+			bias-pull-up;
+			drive-strength = <12>;
+			input-enable;
+			input-schmitt-enable;
+			slew-rate = <0>;
+		};
+	};
+
+	pwmdac_pins: pwmdac-0 {
+		pwmdac-pins {
+			pinmux = <GPIOMUX(33, GPOUT_SYS_PWMDAC_LEFT,
+					      GPOEN_ENABLE,
+					      GPI_NONE)>,
+				 <GPIOMUX(34, GPOUT_SYS_PWMDAC_RIGHT,
+					      GPOEN_ENABLE,
+					      GPI_NONE)>;
+			bias-disable;
+			drive-strength = <2>;
+			input-disable;
+			input-schmitt-disable;
+			slew-rate = <0>;
+		};
+	};
+
+	pwm_pins: pwm-0 {
+		pwm-pins {
+			pinmux = <GPIOMUX(46, GPOUT_SYS_PWM_CHANNEL0,
+					      GPOEN_SYS_PWM0_CHANNEL0,
+					      GPI_NONE)>,
+				 <GPIOMUX(59, GPOUT_SYS_PWM_CHANNEL1,
+					      GPOEN_SYS_PWM0_CHANNEL1,
+					      GPI_NONE)>;
+			bias-disable;
+			drive-strength = <12>;
+			input-disable;
+			input-schmitt-disable;
+			slew-rate = <0>;
+		};
+	};
+
+	spi0_pins: spi0-0 {
+		mosi-pins {
+			pinmux = <GPIOMUX(52, GPOUT_SYS_SPI0_TXD,
+					      GPOEN_ENABLE,
+					      GPI_NONE)>;
+			bias-disable;
+			input-disable;
+			input-schmitt-disable;
+		};
+
+		miso-pins {
+			pinmux = <GPIOMUX(53, GPOUT_LOW,
+					      GPOEN_DISABLE,
+					      GPI_SYS_SPI0_RXD)>;
+			bias-pull-up;
+			input-enable;
+			input-schmitt-enable;
+		};
+
+		sck-pins {
+			pinmux = <GPIOMUX(48, GPOUT_SYS_SPI0_CLK,
+					      GPOEN_ENABLE,
+					      GPI_SYS_SPI0_CLK)>;
+			bias-disable;
+			input-disable;
+			input-schmitt-disable;
+		};
+
+		ss-pins {
+			pinmux = <GPIOMUX(49, GPOUT_SYS_SPI0_FSS,
+					      GPOEN_ENABLE,
+					      GPI_SYS_SPI0_FSS)>;
+			bias-disable;
+			input-disable;
+			input-schmitt-disable;
+		};
+	};
+
+	uart0_pins: uart0-0 {
+		tx-pins {
+			pinmux = <GPIOMUX(5, GPOUT_SYS_UART0_TX,
+					     GPOEN_ENABLE,
+					     GPI_NONE)>;
+			bias-disable;
+			drive-strength = <12>;
+			input-disable;
+			input-schmitt-disable;
+			slew-rate = <0>;
+		};
+
+		rx-pins {
+			pinmux = <GPIOMUX(6, GPOUT_LOW,
+					     GPOEN_DISABLE,
+					     GPI_SYS_UART0_RX)>;
+			bias-disable; /* external pull-up */
+			drive-strength = <2>;
+			input-enable;
+			input-schmitt-enable;
+			slew-rate = <0>;
+		};
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins>;
+	status = "okay";
+};
+
+&usb0 {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&U74_1 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&U74_2 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&U74_3 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&U74_4 {
+	cpu-supply = <&vdd_cpu>;
+};

arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi +1 ~~-585~~

index e19f26628054..9d70f21c86fc 100644
@@ -5,188 +5,11 @@
  */
 
 /dts-v1/;
-#include "jh7110.dtsi"
-#include "jh7110-pinfunc.h"
-#include <dt-bindings/gpio/gpio.h>
+#include "jh7110-common.dtsi"
 
 / {
 	aliases {
-		ethernet0 = &gmac0;
 		ethernet1 = &gmac1;
-		i2c0 = &i2c0;
-		i2c2 = &i2c2;
-		i2c5 = &i2c5;
-		i2c6 = &i2c6;
-		mmc0 = &mmc0;
-		mmc1 = &mmc1;
-		serial0 = &uart0;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	memory@40000000 {
-		device_type = "memory";
-		reg = <0x0 0x40000000 0x1 0x0>;
-	};
-
-	gpio-restart {
-		compatible = "gpio-restart";
-		gpios = <&sysgpio 35 GPIO_ACTIVE_HIGH>;
-		priority = <224>;
-	};
-
-	pwmdac_codec: audio-codec {
-		compatible = "linux,spdif-dit";
-		#sound-dai-cells = <0>;
-	};
-
-	sound {
-		compatible = "simple-audio-card";
-		simple-audio-card,name = "StarFive-PWMDAC-Sound-Card";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		simple-audio-card,dai-link@0 {
-			reg = <0>;
-			format = "left_j";
-			bitclock-master = <&sndcpu0>;
-			frame-master = <&sndcpu0>;
-
-			sndcpu0: cpu {
-				sound-dai = <&pwmdac>;
-			};
-
-			codec {
-				sound-dai = <&pwmdac_codec>;
-			};
-		};
-	};
-};
-
-&cpus {
-	timebase-frequency = <4000000>;
-};
-
-&dvp_clk {
-	clock-frequency = <74250000>;
-};
-
-&gmac0_rgmii_rxin {
-	clock-frequency = <125000000>;
-};
-
-&gmac0_rmii_refin {
-	clock-frequency = <50000000>;
-};
-
-&gmac1_rgmii_rxin {
-	clock-frequency = <125000000>;
-};
-
-&gmac1_rmii_refin {
-	clock-frequency = <50000000>;
-};
-
-&hdmitx0_pixelclk {
-	clock-frequency = <297000000>;
-};
-
-&i2srx_bclk_ext {
-	clock-frequency = <12288000>;
-};
-
-&i2srx_lrck_ext {
-	clock-frequency = <192000>;
-};
-
-&i2stx_bclk_ext {
-	clock-frequency = <12288000>;
-};
-
-&i2stx_lrck_ext {
-	clock-frequency = <192000>;
-};
-
-&mclk_ext {
-	clock-frequency = <12288000>;
-};
-
-&osc {
-	clock-frequency = <24000000>;
-};
-
-&rtc_osc {
-	clock-frequency = <32768>;
-};
-
-&tdm_ext {
-	clock-frequency = <49152000>;
-};
-
-&camss {
-	assigned-clocks = <&ispcrg JH7110_ISPCLK_DOM4_APB_FUNC>,
-			  <&ispcrg JH7110_ISPCLK_MIPI_RX0_PXL>;
-	assigned-clock-rates = <49500000>, <198000000>;
-	status = "okay";
-
-	ports {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		port@0 {
-			reg = <0>;
-		};
-
-		port@1 {
-			reg = <1>;
-
-			camss_from_csi2rx: endpoint {
-				remote-endpoint = <&csi2rx_to_camss>;
-			};
-		};
-	};
-};
-
-&csi2rx {
-	assigned-clocks = <&ispcrg JH7110_ISPCLK_VIN_SYS>;
-	assigned-clock-rates = <297000000>;
-	status = "okay";
-
-	ports {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		port@0 {
-			reg = <0>;
-
-			/* remote MIPI sensor endpoint */
-		};
-
-		port@1 {
-			reg = <1>;
-
-			csi2rx_to_camss: endpoint {
-				remote-endpoint = <&camss_from_csi2rx>;
-			};
-		};
-	};
-};
-
-&gmac0 {
-	phy-handle = <&phy0>;
-	phy-mode = "rgmii-id";
-	status = "okay";
-
-	mdio {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		compatible = "snps,dwmac-mdio";
-
-		phy0: ethernet-phy@0 {
-			reg = <0>;
-		};
 	};
 };

@@ -206,412 +29,6 @@ phy1: ethernet-phy@1 {
 	};
 };
 
-&i2c0 {
-	clock-frequency = <100000>;
-	i2c-sda-hold-time-ns = <300>;
-	i2c-sda-falling-time-ns = <510>;
-	i2c-scl-falling-time-ns = <510>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c0_pins>;
-	status = "okay";
-};
-
-&i2c2 {
-	clock-frequency = <100000>;
-	i2c-sda-hold-time-ns = <300>;
-	i2c-sda-falling-time-ns = <510>;
-	i2c-scl-falling-time-ns = <510>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c2_pins>;
-	status = "okay";
-};
-
-&i2c5 {
-	clock-frequency = <100000>;
-	i2c-sda-hold-time-ns = <300>;
-	i2c-sda-falling-time-ns = <510>;
-	i2c-scl-falling-time-ns = <510>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c5_pins>;
-	status = "okay";
-
-	axp15060: pmic@36 {
-		compatible = "x-powers,axp15060";
-		reg = <0x36>;
-		interrupt-controller;
-		#interrupt-cells = <1>;
-
-		regulators {
-			vcc_3v3: dcdc1 {
-				regulator-boot-on;
-				regulator-always-on;
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-name = "vcc_3v3";
-			};
-
-			vdd_cpu: dcdc2 {
-				regulator-always-on;
-				regulator-min-microvolt = <500000>;
-				regulator-max-microvolt = <1540000>;
-				regulator-name = "vdd-cpu";
-			};
-
-			emmc_vdd: aldo4 {
-				regulator-boot-on;
-				regulator-always-on;
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-				regulator-name = "emmc_vdd";
-			};
-		};
-	};
-};
-
-&i2c6 {
-	clock-frequency = <100000>;
-	i2c-sda-hold-time-ns = <300>;
-	i2c-sda-falling-time-ns = <510>;
-	i2c-scl-falling-time-ns = <510>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c6_pins>;
-	status = "okay";
-};
-
 &mmc0 {
-	max-frequency = <100000000>;
-	assigned-clocks = <&syscrg JH7110_SYSCLK_SDIO0_SDCARD>;
-	assigned-clock-rates = <50000000>;
-	bus-width = <8>;
-	cap-mmc-highspeed;
-	mmc-ddr-1_8v;
-	mmc-hs200-1_8v;
 	non-removable;
-	cap-mmc-hw-reset;
-	post-power-on-delay-ms = <200>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins>;
-	vmmc-supply = <&vcc_3v3>;
-	vqmmc-supply = <&emmc_vdd>;
-	status = "okay";
-};
-
-&mmc1 {
-	max-frequency = <100000000>;
-	assigned-clocks = <&syscrg JH7110_SYSCLK_SDIO1_SDCARD>;
-	assigned-clock-rates = <50000000>;
-	bus-width = <4>;
-	no-sdio;
-	no-mmc;
-	cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
-	disable-wp;
-	cap-sd-highspeed;
-	post-power-on-delay-ms = <200>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc1_pins>;
-	status = "okay";
-};
-
-&pwmdac {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pwmdac_pins>;
-	status = "okay";
-};
-
-&qspi {
-	#address-cells = <1>;
-	#size-cells = <0>;
-	status = "okay";
-
-	nor_flash: flash@0 {
-		compatible = "jedec,spi-nor";
-		reg = <0>;
-		cdns,read-delay = <5>;
-		spi-max-frequency = <12000000>;
-		cdns,tshsl-ns = <1>;
-		cdns,tsd2d-ns = <1>;
-		cdns,tchsh-ns = <1>;
-		cdns,tslch-ns = <1>;
-
-		partitions {
-			compatible = "fixed-partitions";
-			#address-cells = <1>;
-			#size-cells = <1>;
-
-			spl@0 {
-				reg = <0x0 0x80000>;
-			};
-			uboot-env@f0000 {
-				reg = <0xf0000 0x10000>;
-			};
-			uboot@100000 {
-				reg = <0x100000 0x400000>;
-			};
-			reserved-data@600000 {
-				reg = <0x600000 0xa00000>;
-			};
-		};
-	};
-};
-
-&pwm {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pwm_pins>;
-	status = "okay";
-};
-
-&spi0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&spi0_pins>;
-	status = "okay";
-
-	spi_dev0: spi@0 {
-		compatible = "rohm,dh2228fv";
-		reg = <0>;
-		spi-max-frequency = <10000000>;
-	};
-};
-
-&sysgpio {
-	i2c0_pins: i2c0-0 {
-		i2c-pins {
-			pinmux = <GPIOMUX(57, GPOUT_LOW,
-					      GPOEN_SYS_I2C0_CLK,
-					      GPI_SYS_I2C0_CLK)>,
-				 <GPIOMUX(58, GPOUT_LOW,
-					      GPOEN_SYS_I2C0_DATA,
-					      GPI_SYS_I2C0_DATA)>;
-			bias-disable; /* external pull-up */
-			input-enable;
-			input-schmitt-enable;
-		};
-	};
-
-	i2c2_pins: i2c2-0 {
-		i2c-pins {
-			pinmux = <GPIOMUX(3, GPOUT_LOW,
-					     GPOEN_SYS_I2C2_CLK,
-					     GPI_SYS_I2C2_CLK)>,
-				 <GPIOMUX(2, GPOUT_LOW,
-					     GPOEN_SYS_I2C2_DATA,
-					     GPI_SYS_I2C2_DATA)>;
-			bias-disable; /* external pull-up */
-			input-enable;
-			input-schmitt-enable;
-		};
-	};
-
-	i2c5_pins: i2c5-0 {
-		i2c-pins {
-			pinmux = <GPIOMUX(19, GPOUT_LOW,
-					      GPOEN_SYS_I2C5_CLK,
-					      GPI_SYS_I2C5_CLK)>,
-				 <GPIOMUX(20, GPOUT_LOW,
-					      GPOEN_SYS_I2C5_DATA,
-					      GPI_SYS_I2C5_DATA)>;
-			bias-disable; /* external pull-up */
-			input-enable;
-			input-schmitt-enable;
-		};
-	};
-
-	i2c6_pins: i2c6-0 {
-		i2c-pins {
-			pinmux = <GPIOMUX(16, GPOUT_LOW,
-					      GPOEN_SYS_I2C6_CLK,
-					      GPI_SYS_I2C6_CLK)>,
-				 <GPIOMUX(17, GPOUT_LOW,
-					      GPOEN_SYS_I2C6_DATA,
-					      GPI_SYS_I2C6_DATA)>;
-			bias-disable; /* external pull-up */
-			input-enable;
-			input-schmitt-enable;
-		};
-	};
-
-	mmc0_pins: mmc0-0 {
-		 rst-pins {
-			pinmux = <GPIOMUX(62, GPOUT_SYS_SDIO0_RST,
-					      GPOEN_ENABLE,
-					      GPI_NONE)>;
-			bias-pull-up;
-			drive-strength = <12>;
-			input-disable;
-			input-schmitt-disable;
-			slew-rate = <0>;
-		};
-
-		mmc-pins {
-			pinmux = <PINMUX(64, 0)>,
-				 <PINMUX(65, 0)>,
-				 <PINMUX(66, 0)>,
-				 <PINMUX(67, 0)>,
-				 <PINMUX(68, 0)>,
-				 <PINMUX(69, 0)>,
-				 <PINMUX(70, 0)>,
-				 <PINMUX(71, 0)>,
-				 <PINMUX(72, 0)>,
-				 <PINMUX(73, 0)>;
-			bias-pull-up;
-			drive-strength = <12>;
-			input-enable;
-		};
-	};
-
-	mmc1_pins: mmc1-0 {
-		clk-pins {
-			pinmux = <GPIOMUX(10, GPOUT_SYS_SDIO1_CLK,
-					      GPOEN_ENABLE,
-					      GPI_NONE)>;
-			bias-pull-up;
-			drive-strength = <12>;
-			input-disable;
-			input-schmitt-disable;
-			slew-rate = <0>;
-		};
-
-		mmc-pins {
-			pinmux = <GPIOMUX(9, GPOUT_SYS_SDIO1_CMD,
-					     GPOEN_SYS_SDIO1_CMD,
-					     GPI_SYS_SDIO1_CMD)>,
-				 <GPIOMUX(11, GPOUT_SYS_SDIO1_DATA0,
-					      GPOEN_SYS_SDIO1_DATA0,
-					      GPI_SYS_SDIO1_DATA0)>,
-				 <GPIOMUX(12, GPOUT_SYS_SDIO1_DATA1,
-					      GPOEN_SYS_SDIO1_DATA1,
-					      GPI_SYS_SDIO1_DATA1)>,
-				 <GPIOMUX(7, GPOUT_SYS_SDIO1_DATA2,
-					     GPOEN_SYS_SDIO1_DATA2,
-					     GPI_SYS_SDIO1_DATA2)>,
-				 <GPIOMUX(8, GPOUT_SYS_SDIO1_DATA3,
-					     GPOEN_SYS_SDIO1_DATA3,
-					     GPI_SYS_SDIO1_DATA3)>;
-			bias-pull-up;
-			drive-strength = <12>;
-			input-enable;
-			input-schmitt-enable;
-			slew-rate = <0>;
-		};
-	};
-
-	pwmdac_pins: pwmdac-0 {
-		pwmdac-pins {
-			pinmux = <GPIOMUX(33, GPOUT_SYS_PWMDAC_LEFT,
-					      GPOEN_ENABLE,
-					      GPI_NONE)>,
-				 <GPIOMUX(34, GPOUT_SYS_PWMDAC_RIGHT,
-					      GPOEN_ENABLE,
-					      GPI_NONE)>;
-			bias-disable;
-			drive-strength = <2>;
-			input-disable;
-			input-schmitt-disable;
-			slew-rate = <0>;
-		};
-	};
-
-	pwm_pins: pwm-0 {
-		pwm-pins {
-			pinmux = <GPIOMUX(46, GPOUT_SYS_PWM_CHANNEL0,
-					      GPOEN_SYS_PWM0_CHANNEL0,
-					      GPI_NONE)>,
-				 <GPIOMUX(59, GPOUT_SYS_PWM_CHANNEL1,
-					      GPOEN_SYS_PWM0_CHANNEL1,
-					      GPI_NONE)>;
-			bias-disable;
-			drive-strength = <12>;
-			input-disable;
-			input-schmitt-disable;
-			slew-rate = <0>;
-		};
-	};
-
-	spi0_pins: spi0-0 {
-		mosi-pins {
-			pinmux = <GPIOMUX(52, GPOUT_SYS_SPI0_TXD,
-					      GPOEN_ENABLE,
-					      GPI_NONE)>;
-			bias-disable;
-			input-disable;
-			input-schmitt-disable;
-		};
-
-		miso-pins {
-			pinmux = <GPIOMUX(53, GPOUT_LOW,
-					      GPOEN_DISABLE,
-					      GPI_SYS_SPI0_RXD)>;
-			bias-pull-up;
-			input-enable;
-			input-schmitt-enable;
-		};
-
-		sck-pins {
-			pinmux = <GPIOMUX(48, GPOUT_SYS_SPI0_CLK,
-					      GPOEN_ENABLE,
-					      GPI_SYS_SPI0_CLK)>;
-			bias-disable;
-			input-disable;
-			input-schmitt-disable;
-		};
-
-		ss-pins {
-			pinmux = <GPIOMUX(49, GPOUT_SYS_SPI0_FSS,
-					      GPOEN_ENABLE,
-					      GPI_SYS_SPI0_FSS)>;
-			bias-disable;
-			input-disable;
-			input-schmitt-disable;
-		};
-	};
-
-	uart0_pins: uart0-0 {
-		tx-pins {
-			pinmux = <GPIOMUX(5, GPOUT_SYS_UART0_TX,
-					     GPOEN_ENABLE,
-					     GPI_NONE)>;
-			bias-disable;
-			drive-strength = <12>;
-			input-disable;
-			input-schmitt-disable;
-			slew-rate = <0>;
-		};
-
-		rx-pins {
-			pinmux = <GPIOMUX(6, GPOUT_LOW,
-					     GPOEN_DISABLE,
-					     GPI_SYS_UART0_RX)>;
-			bias-disable; /* external pull-up */
-			drive-strength = <2>;
-			input-enable;
-			input-schmitt-enable;
-			slew-rate = <0>;
-		};
-	};
-};
-
-&uart0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins>;
-	status = "okay";
-};
-
-&usb0 {
-	dr_mode = "peripheral";
-	status = "okay";
-};
-
-&U74_1 {
-	cpu-supply = <&vdd_cpu>;
-};
-
-&U74_2 {
-	cpu-supply = <&vdd_cpu>;
-};
-
-&U74_3 {
-	cpu-supply = <&vdd_cpu>;
-};
-
-&U74_4 {
-	cpu-supply = <&vdd_cpu>;
 };
--

2.43.0

Jisheng Zhang

author

2024-04-29 00:27 UTC #11 lore raw

PATCH v4 8/8 riscv: dts: starfive: add Milkv Mars board device tree

In reply to Jisheng Zhang

The Milkv Mars is a development board based on the Starfive JH7110 SoC. The board features:

Add the devicetree file describing the currently supported features, namely PMIC, UART, I2C, GPIO, SD card, QSPI Flash, eMMC and Ethernet.

Signed-off-by Jisheng Zhang <[email protected]>

---
 arch/riscv/boot/dts/starfive/Makefile         |  1 +
 .../boot/dts/starfive/jh7110-milkv-mars.dts   | 30 +++++++++++++++++++
 2 files changed, 31 insertions(+)
 create mode 100644 arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts

arch/riscv/boot/dts/starfive/Makefile +1 -0

index 0141504c0f5c..2fa0cd7f31c3 100644
@@ -8,5 +8,6 @@ DTC_FLAGS_jh7110-starfive-visionfive-2-v1.3b := -@
 dtb-$(CONFIG_ARCH_STARFIVE) += jh7100-beaglev-starlight.dtb
 dtb-$(CONFIG_ARCH_STARFIVE) += jh7100-starfive-visionfive-v1.dtb
 
+dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-milkv-mars.dtb
 dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-starfive-visionfive-2-v1.2a.dtb
 dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-starfive-visionfive-2-v1.3b.dtb

arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts new file +30 -0

new file mode 100644
index 000000000000..fa0eac78e0ba
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+/*
+ * Copyright (C) 2023 Jisheng Zhang <[email protected]>
+ */
+
+/dts-v1/;
+#include "jh7110-common.dtsi"
+
+/ {
+	model = "Milk-V Mars";
+	compatible = "milkv,mars", "starfive,jh7110";
+};
+
+&gmac0 {
+	starfive,tx-use-rgmii-clk;
+	assigned-clocks = <&aoncrg JH7110_AONCLK_GMAC0_TX>;
+	assigned-clock-parents = <&aoncrg JH7110_AONCLK_GMAC0_RMII_RTX>;
+};
+
+
+&phy0 {
+	motorcomm,tx-clk-adj-enabled;
+	motorcomm,tx-clk-10-inverted;
+	motorcomm,tx-clk-100-inverted;
+	motorcomm,tx-clk-1000-inverted;
+	motorcomm,rx-clk-drv-microamp = <3970>;
+	motorcomm,rx-data-drv-microamp = <2910>;
+	rx-internal-delay-ps = <1500>;
+	tx-internal-delay-ps = <1500>;
+};

Signature · 1 line

2.43.0

Emil Renner Berthing

Reviewed-by on v4 8/8

2024-04-29 13:52 UTC #12 lore raw

Quoted 18 lines · Jisheng Zhang

The Milkv Mars is a development board based on the Starfive JH7110 SoC. The board features:
- JH7110 SoC
- 1/2/4/8 GiB LPDDR4 DRAM
- AXP15060 PMIC
- 40 pin GPIO header
- 3x USB 3.0 host port
- 1x USB 2.0 host port
- 1x M.2 E-Key
- 1x eMMC slot
- 1x MicroSD slot
- 1x QSPI Flash
- 1x 1Gbps Ethernet port
- 1x HDMI port
- 1x 2-lane DSI and 1x 4-lane DSI
- 1x 2-lane CSI

Quoted 4 lines

Add the devicetree file describing the currently supported features, namely PMIC, UART, I2C, GPIO, SD card, QSPI Flash, eMMC and Ethernet.
Signed-off-by Jisheng Zhang <[email protected]>

Reviewed-by Emil Renner Berthing <[email protected]>

Conor Dooley

maintainer Applied

2024-04-30 21:22 UTC #13 lore raw

In reply to Jisheng Zhang

From: Conor Dooley <[email protected]>

Quoted 18 lines · Jisheng Zhang

The Milkv Mars is a development board based on the Starfive JH7110 SoC. The board features:
- JH7110 SoC
- 1/2/4/8 GiB LPDDR4 DRAM
- AXP15060 PMIC
- 40 pin GPIO header
- 3x USB 3.0 host port
- 1x USB 2.0 host port
- 1x M.2 E-Key
- 1x eMMC slot
- 1x MicroSD slot
- 1x QSPI Flash
- 1x 1Gbps Ethernet port
- 1x HDMI port
- 1x 2-lane DSI and 1x 4-lane DSI
- 1x 2-lane CSI

Quoted 1 line

[...]

Applied to riscv-dt-for-next, thanks! I fixed up the nits of Emil's in the merge commit.

[1/8] riscv: dts: starfive: add 'cpus' label to jh7110 and jh7100 soc dtsi

      https://git.kernel.org/conor/c/5e7922abddd4
[2/8] dt-bindings: riscv: starfive: add Milkv Mars board
      https://git.kernel.org/conor/c/4c536aa462f1
[3/8] riscv: dts: starfive: visionfive 2: update sound and codec dt node name
      https://git.kernel.org/conor/c/b9a1481f259c
[4/8] riscv: dts: starfive: visionfive 2: use cpus label for timebase freq
      https://git.kernel.org/conor/c/ffddddf4aa8d
[5/8] riscv: dts: starfive: visionfive 2: add tf cd-gpios
      https://git.kernel.org/conor/c/0ffce9d49abd
[6/8] riscv: dts: starfive: visionfive 2: add "disable-wp" for tfcard
      https://git.kernel.org/conor/c/07da6ddf510b
[7/8] riscv: dts: starfive: introduce a common board dtsi for jh7110 based boards
      https://git.kernel.org/conor/c/ac9a37e2d6b6
[8/8] riscv: dts: starfive: add Milkv Mars board device tree
      https://git.kernel.org/conor/c/9276badd9d03

Thanks,
Conor.