iommu/arm-smmu-v3: Add support for ECMDQ register mode
Subsystems (2)
v3 cover iommu/arm-smmu-v3: Add support for ECMDQ register mode
Resending the patches by Zhen Lei <[email protected]> that add support for SMMU ECMDQ feature.
Tested this feature on a Marvell SoC by implementing a smmu-test driver. This test driver spawns a thread per CPU and each thread keeps sending map, table-walk and unmap requests for a fixed duration.
Using this test driver, we compared ECMDQ vs SMMU with software batching support and saw ~5% improvement with ECMDQ. Performance numbers are mentioned below:
Total Requests Average Requests Difference
Per CPU wrt ECMDQ
-----------------------------------------------------------------
ECMDQ 239286381 2991079 CMDQ Batch Size 1 228232187 2852902 -4.62% CMDQ Batch Size 32 233465784 2918322 -2.43% CMDQ Batch Size 64 231679588 2895994 -3.18% CMDQ Batch Size 128 233189030 2914862 -2.55% CMDQ Batch Size 256 230965773 2887072 -3.48%
v2 --> v3:
1. Rebased on linux 6.9-rc5
v1 --> v2:
1. Drop patch "iommu/arm-smmu-v3: Add arm_smmu_ecmdq_issue_cmdlist() for non-shared ECMDQ" in v1
2. Drop patch "iommu/arm-smmu-v3: Add support for less than one ECMDQ per core" in v1
3. Replace rwlock with IPI to support lockless protection against the write operation to bit
'ERRACK' during error handling and the read operation to bit 'ERRACK'
during command insertion.
4. Standardize variable names.
- struct arm_smmu_ecmdq *__percpu *ecmdq;
+ struct arm_smmu_ecmdq *__percpu *ecmdqs;
5. Add member 'iobase' to struct arm_smmu_device to record the start physical
address of the SMMU, to replace translation operation
(vmalloc_to_pfn(smmu->base) << PAGE_SHIFT)
+ phys_addr_t iobase;
- smmu_dma_base = (vmalloc_to_pfn(smmu->base) << PAGE_SHIFT);
6. Cancel below union. Whether ECMDQ is enabled is determined only based on 'ecmdq_enabled'.
- union {
- u32 nr_ecmdq;
- u32 ecmdq_enabled;
- };
+ u32 nr_ecmdq;
+ bool ecmdq_enabled;
7. Eliminate some sparse check warnings. For example.
- struct arm_smmu_ecmdq *ecmdq;
+ struct arm_smmu_ecmdq __percpu *ecmdq;
Zhen Lei (2):
iommu/arm-smmu-v3: Add support for ECMDQ register mode iommu/arm-smmu-v3: Ensure that a set of associated commands are
inserted in the same ECMDQ
drivers/iommu/arm/arm-smmu-v3/arm-smmu-v3.c | 261 +++++++++++++++++++- drivers/iommu/arm/arm-smmu-v3/arm-smmu-v3.h | 33 +++ 2 files changed, 286 insertions(+), 8 deletions(-)
Signature · 1 line
2.34.1
PATCH v3 1/2 iommu/arm-smmu-v3: Add support for ECMDQ register mode
From: Zhen Lei <[email protected]>
Ensure that each core exclusively occupies an ECMDQ and all of them are enabled during initialization. During this initialization process, any errors will result in a fallback to using normal CMDQ.
When GERROR is triggered by ECMDQ, all ECMDQs need to be traversed: the ECMDQs with errors will be processed and the ECMDQs without errors will be skipped directly. Compared with register SMMU_CMDQ_PROD, register SMMU_ECMDQ_PROD has one more 'EN' bit and one more 'ERRACK' bit. After the error indicated by SMMU_GERROR.CMDQP_ERR is fixed, the 'ERRACK' bit needs to be toggled to resume the corresponding ECMDQ. In order to lockless protection against the write operation to bit 'ERRACK' during error handling and the read operation to bit 'ERRACK' during command insertion. Send IPI to the faulty CPU and perform the toggle operation on the faulty CPU. Because the command insertion is protected by local_irq_save(), so no race.
--- drivers/iommu/arm/arm-smmu-v3/arm-smmu-v3.c | 219 +++++++++++++++++++- drivers/iommu/arm/arm-smmu-v3/arm-smmu-v3.h | 33 +++ 2 files changed, 251 insertions(+), 1 deletion(-)
drivers/iommu/arm/arm-smmu-v3/arm-smmu-v3.c +218 -1
@@ -352,6 +352,14 @@ static int arm_smmu_cmdq_build_cmd(u64 *cmd, struct arm_smmu_cmdq_ent *ent)static struct arm_smmu_cmdq *arm_smmu_get_cmdq (struct arm_smmu_device *smmu) { +if (smmu->ecmdq_enabled) { +struct arm_smmu_ecmdq *ecmdq; + + ecmdq = *this_cpu_ptr (smmu->ecmdqs); + +return &ecmdq->cmdq; + } +return &smmu->cmdq; }
@@ -434,6 +442,43 @@ static void arm_smmu_cmdq_skip_err(struct arm_smmu_device *smmu)__arm_smmu_cmdq_skip_err (smmu, &smmu->cmdq.q); } +static void arm_smmu_ecmdq_err_ack (void *info) +{ +u32 prod, cons; +struct arm_smmu_queue *q = info; + + prod =readl_relaxed (q->prod_reg); + cons =readl_relaxed (q->cons_reg); + prod &= ~ECMDQ_PROD_ERRACK ; + prod |= cons &ECMDQ_CONS_ERR ; +writel (prod, q->prod_reg); +} + +static void arm_smmu_ecmdq_skip_err (struct arm_smmu_device *smmu) +{ +int i; +u32 prod, cons; +struct arm_smmu_queue *q; +struct arm_smmu_ecmdq *ecmdq; + +if (!smmu->ecmdq_enabled) +return ; + +for (i =0 ; i < smmu->nr_ecmdq; i++) { + ecmdq = *per_cpu_ptr (smmu->ecmdqs, i); + q = &ecmdq->cmdq.q; + + prod =readl_relaxed (q->prod_reg); + cons =readl_relaxed (q->cons_reg); +if (((prod ^ cons) &ECMDQ_CONS_ERR ) ==0 ) +continue ; + +__arm_smmu_cmdq_skip_err (smmu, q); + +smp_call_function_single (i, arm_smmu_ecmdq_err_ack, q, true); + } +} +/* * Command queue locking. * This is a form of bastardised rwlock with the following major changes:
@@ -830,7 +875,10 @@ static int arm_smmu_cmdq_issue_cmdlist(struct arm_smmu_device *smmu,* d. Advance the hardware prod pointer * Control dependency ordering from the entries becoming valid. */ -writel_relaxed (prod, cmdq->q.prod_reg); +if (smmu->ecmdq_enabled) +writel_relaxed (prod |ECMDQ_PROD_EN , cmdq->q.prod_reg); +else +writel_relaxed (prod, cmdq->q.prod_reg);/* * e. Tell the next owner we're done
@@ -1838,6 +1886,9 @@ static irqreturn_t arm_smmu_gerror_handler(int irq, void *dev)if (active &GERROR_CMDQ_ERR )arm_smmu_cmdq_skip_err (smmu); +if (active &GERROR_CMDQP_ERR ) +arm_smmu_ecmdq_skip_err (smmu); +writel (gerror, smmu->base +ARM_SMMU_GERRORN );return IRQ_HANDLED ; }
@@ -3154,6 +3205,20 @@ static int arm_smmu_cmdq_init(struct arm_smmu_device *smmu)return 0 ; } +static int arm_smmu_ecmdq_init (struct arm_smmu_cmdq *cmdq) +{ +unsigned int nents =1 << cmdq->q.llq.max_n_shift; + +atomic_set (&cmdq->owner_prod,0 ); +atomic_set (&cmdq->lock,0 ); + + cmdq->valid_map = (atomic_long_t *)bitmap_zalloc (nents,GFP_KERNEL ); +if (!cmdq->valid_map) +return -ENOMEM ; + +return 0 ; +} +static int arm_smmu_init_queues (struct arm_smmu_device *smmu) {int ret;
@@ -3503,6 +3568,36 @@ static int arm_smmu_device_disable(struct arm_smmu_device *smmu)return ret; } +static void arm_smmu_ecmdq_reset (struct arm_smmu_device *smmu) +{ +u32 reg; +int i, ret; +struct arm_smmu_queue *q; +struct arm_smmu_ecmdq *ecmdq; + +if (!smmu->ecmdq_enabled) +return ; + +for (i =0 ; i < smmu->nr_ecmdq; i++) { + ecmdq = *per_cpu_ptr (smmu->ecmdqs, i); + + q = &ecmdq->cmdq.q; +writeq_relaxed (q->q_base, ecmdq->base +ARM_SMMU_ECMDQ_BASE ); +writel_relaxed (q->llq.prod, ecmdq->base +ARM_SMMU_ECMDQ_PROD ); +writel_relaxed (q->llq.cons, ecmdq->base +ARM_SMMU_ECMDQ_CONS ); + +/* enable ecmdq */ +writel (ECMDQ_PROD_EN , q->prod_reg); + ret =readl_relaxed_poll_timeout (q->cons_reg, reg, reg &ECMDQ_CONS_ENACK , +1 ,ARM_SMMU_POLL_TIMEOUT_US ); +if (ret) { +dev_err (smmu->dev,"ecmdq[%d] enable failed\n" , i); + smmu->ecmdq_enabled = false; +break ; + } + } +} +static int arm_smmu_device_reset (struct arm_smmu_device *smmu,bool bypass) {int ret;
@@ -3557,6 +3652,8 @@ static int arm_smmu_device_reset(struct arm_smmu_device *smmu, bool bypass)return ret; } +arm_smmu_ecmdq_reset (smmu); +/* Invalidate any cached configuration */ cmd.opcode =CMDQ_OP_CFGI_ALL ;arm_smmu_cmdq_issue_cmd_with_sync (smmu, &cmd);
@@ -3674,6 +3771,112 @@ static void arm_smmu_device_iidr_probe(struct arm_smmu_device *smmu) }break ; } +}; + +static int arm_smmu_ecmdq_layout (struct arm_smmu_device *smmu) +{ +int cpu; +struct arm_smmu_ecmdq __percpu *ecmdq; + +if (num_possible_cpus () <= smmu->nr_ecmdq) { + ecmdq =devm_alloc_percpu (smmu->dev, *ecmdq); +if (!ecmdq) +return -ENOMEM ; + +for_each_possible_cpu (cpu) + *per_cpu_ptr (smmu->ecmdqs, cpu) =per_cpu_ptr (ecmdq, cpu); + +/* A core requires at most one ECMDQ */ + smmu->nr_ecmdq =num_possible_cpus (); + +return 0 ; + } + +return -ENOSPC ; +} + +static int arm_smmu_ecmdq_probe (struct arm_smmu_device *smmu) +{ +int ret, cpu; +u32 i, nump, numq, gap; +u32 reg, shift_increment; +u64 offset; +void __iomem *cp_regs, *cp_base; + +/* IDR6 */ + reg =readl_relaxed (smmu->base +ARM_SMMU_IDR6 ); + nump =1 <<FIELD_GET (IDR6_LOG2NUMP , reg); + numq =1 <<FIELD_GET (IDR6_LOG2NUMQ , reg); + smmu->nr_ecmdq = nump * numq; + gap =ECMDQ_CP_RRESET_SIZE >>FIELD_GET (IDR6_LOG2NUMQ , reg); + + cp_regs =ioremap (smmu->iobase +ARM_SMMU_ECMDQ_CP_BASE ,PAGE_SIZE ); +if (!cp_regs) +return -ENOMEM ; + +for (i =0 ; i < nump; i++) { +u64 val, pre_addr =0 ; + + val =readq_relaxed (cp_regs +32 * i); +if (!(val &ECMDQ_CP_PRESET )) { +iounmap (cp_regs); +dev_err (smmu->dev,"ecmdq control page %u is memory mode\n" , i); +return -EFAULT ; + } + +if (i && ((val &ECMDQ_CP_ADDR ) != (pre_addr +ECMDQ_CP_RRESET_SIZE ))) { +iounmap (cp_regs); +dev_err (smmu->dev,"ecmdq_cp memory region is not contiguous\n" ); +return -EFAULT ; + } + + pre_addr = val &ECMDQ_CP_ADDR ; + } + + offset =readl_relaxed (cp_regs) &ECMDQ_CP_ADDR ; +iounmap (cp_regs); + + cp_base =devm_ioremap (smmu->dev, smmu->iobase + offset,ECMDQ_CP_RRESET_SIZE * nump); +if (!cp_base) +return -ENOMEM ; + + smmu->ecmdqs = devm_alloc_percpu(smmu->dev, struct arm_smmu_ecmdq *); +if (!smmu->ecmdqs) +return -ENOMEM ; + + ret =arm_smmu_ecmdq_layout (smmu); +if (ret) +return ret; + + shift_increment =order_base_2 (num_possible_cpus () / smmu->nr_ecmdq); + + offset =0 ; +for_each_possible_cpu (cpu) { +struct arm_smmu_ecmdq *ecmdq; +struct arm_smmu_queue *q; + + ecmdq = *per_cpu_ptr (smmu->ecmdqs, cpu); + ecmdq->base = cp_base + offset; + + q = &ecmdq->cmdq.q; + + q->llq.max_n_shift =ECMDQ_MAX_SZ_SHIFT + shift_increment; + ret =arm_smmu_init_one_queue (smmu, q, ecmdq->base,ARM_SMMU_ECMDQ_PROD , +ARM_SMMU_ECMDQ_CONS ,CMDQ_ENT_DWORDS ,"ecmdq" ); +if (ret) +return ret; + + ret =arm_smmu_ecmdq_init (&ecmdq->cmdq); +if (ret) { +dev_err (smmu->dev,"ecmdq[%d] init failed\n" , i); +return ret; + } + + offset += gap; + } + smmu->ecmdq_enabled = true; + +return 0 ; }static int arm_smmu_device_hw_probe (struct arm_smmu_device *smmu)
@@ -3789,6 +3992,9 @@ static int arm_smmu_device_hw_probe(struct arm_smmu_device *smmu)if (reg &IDR1_ATTR_TYPES_OVR ) smmu->features |=ARM_SMMU_FEAT_ATTR_TYPES_OVR ; +if (reg &IDR1_ECMDQ ) + smmu->features |=ARM_SMMU_FEAT_ECMDQ ; +/* Queue sizes, capped to ensure natural alignment */ smmu->cmdq.q.llq.max_n_shift =min_t (u32,CMDQ_MAX_SZ_SHIFT ,FIELD_GET (IDR1_CMDQS , reg));
@@ -3896,6 +4102,16 @@ static int arm_smmu_device_hw_probe(struct arm_smmu_device *smmu)dev_info (smmu->dev,"ias %lu-bit, oas %lu-bit (features 0x%08x)\n" , smmu->ias, smmu->oas, smmu->features); + +if (smmu->features &ARM_SMMU_FEAT_ECMDQ ) { +int err; + + err =arm_smmu_ecmdq_probe (smmu); +if (err) { +dev_err (smmu->dev,"suppress ecmdq feature, errno=%d\n" , err); + smmu->ecmdq_enabled = false; + } + }return 0 ; }
@@ -4054,6 +4270,7 @@ static int arm_smmu_device_probe(struct platform_device *pdev) smmu->base =arm_smmu_ioremap (dev, ioaddr,ARM_SMMU_REG_SZ );if (IS_ERR (smmu->base))return PTR_ERR (smmu->base); + smmu->iobase = ioaddr;if (arm_smmu_resource_size (smmu) >SZ_64K ) { smmu->page1 = arm_smmu_ioremap(dev, ioaddr + SZ_64K,
drivers/iommu/arm/arm-smmu-v3/arm-smmu-v3.h +33 -0
@@ -41,6 +41,7 @@#define IDR0_S2P (1 << 0)#define ARM_SMMU_IDR1 0x4 +#define IDR1_ECMDQ (1 << 31)#define IDR1_TABLES_PRESET (1 << 30)#define IDR1_QUEUES_PRESET (1 << 29)#define IDR1_REL (1 << 28)
@@ -114,6 +115,7 @@#define ARM_SMMU_IRQ_CTRLACK 0x54#define ARM_SMMU_GERROR 0x60 +#define GERROR_CMDQP_ERR (1 << 9)#define GERROR_SFM_ERR (1 << 8)#define GERROR_MSI_GERROR_ABT_ERR (1 << 7)#define GERROR_MSI_PRIQ_ABT_ERR (1 << 6)
@@ -159,6 +161,26 @@#define ARM_SMMU_PRIQ_IRQ_CFG1 0xd8#define ARM_SMMU_PRIQ_IRQ_CFG2 0xdc +#define ARM_SMMU_IDR6 0x190 +#define IDR6_LOG2NUMP GENMASK(27, 24) +#define IDR6_LOG2NUMQ GENMASK(19, 16) +#define IDR6_BA_DOORBELLS GENMASK(9, 0) + +#define ARM_SMMU_ECMDQ_BASE 0x00 +#define ARM_SMMU_ECMDQ_PROD 0x08 +#define ARM_SMMU_ECMDQ_CONS 0x0c +#define ECMDQ_MAX_SZ_SHIFT 8 +#define ECMDQ_PROD_EN (1 << 31) +#define ECMDQ_CONS_ENACK (1 << 31) +#define ECMDQ_CONS_ERR (1 << 23) +#define ECMDQ_PROD_ERRACK (1 << 23) + +#define ARM_SMMU_ECMDQ_CP_BASE 0x4000 +#define ECMDQ_CP_ADDR GENMASK_ULL(51, 12) +#define ECMDQ_CP_CMDQGS GENMASK_ULL(2, 1) +#define ECMDQ_CP_PRESET (1UL << 0) +#define ECMDQ_CP_RRESET_SIZE 0x10000 +#define ARM_SMMU_REG_SZ 0xe00/* Common MSI config fields */
@@ -558,6 +580,11 @@ struct arm_smmu_cmdq {atomic_t lock; }; +struct arm_smmu_ecmdq { +struct arm_smmu_cmdq cmdq; +void __iomem *base; +}; +struct arm_smmu_cmdq_batch {u64 cmds[CMDQ_BATCH_ENTRIES *CMDQ_ENT_DWORDS ];int num;
@@ -627,6 +654,7 @@ struct arm_smmu_device {struct device *dev;void __iomem *base;void __iomem *page1; +phys_addr_t iobase;#define ARM_SMMU_FEAT_2_LVL_STRTAB (1 << 0)#define ARM_SMMU_FEAT_2_LVL_CDTAB (1 << 1)
@@ -649,6 +677,7 @@ struct arm_smmu_device {#define ARM_SMMU_FEAT_E2H (1 << 18)#define ARM_SMMU_FEAT_NESTING (1 << 19)#define ARM_SMMU_FEAT_ATTR_TYPES_OVR (1 << 20) +#define ARM_SMMU_FEAT_ECMDQ (1 << 21)u32 features;#define ARM_SMMU_OPT_SKIP_PREFETCH (1 << 0)
@@ -657,6 +686,10 @@ struct arm_smmu_device {#define ARM_SMMU_OPT_CMDQ_FORCE_SYNC (1 << 3)u32 options; +struct arm_smmu_ecmdq *__percpu *ecmdqs; +u32 nr_ecmdq; +bool ecmdq_enabled; +struct arm_smmu_cmdq cmdq;struct arm_smmu_evtq evtq;struct arm_smmu_priq priq;
Signature · 1 line
2.34.1
Quoted 11 lines · Tanmay Jagdale
drivers/iommu/arm/arm-smmu-v3/arm-smmu-v3.c +11
-0+static int arm_smmu_ecmdq_probe (struct arm_smmu_device *smmu) +{ +int ret, cpu; +u32 i, nump, numq, gap; +u32 reg, shift_increment; +u64 offset; +void __iomem *cp_regs, *cp_base; + +/* IDR6 */ + reg =readl_relaxed (smmu->base +ARM_SMMU_IDR6 ); + nump =1 <<FIELD_GET (IDR6_LOG2NUMP , reg);
drivers/iommu/arm/arm-smmu-v3/arm-smmu-v3.c static void arm_smmu_device_iidr_probe(struct arm_smmu_device *smmu) · line 3818
Quoted 10 lines
drivers/iommu/arm/arm-smmu-v3/arm-smmu-v3.c +10
-0+ numq =1 <<FIELD_GET (IDR6_LOG2NUMQ , reg); + smmu->nr_ecmdq = nump * numq; + gap =ECMDQ_CP_RRESET_SIZE >>FIELD_GET (IDR6_LOG2NUMQ , reg); + + cp_regs =ioremap (smmu->iobase +ARM_SMMU_ECMDQ_CP_BASE ,PAGE_SIZE ); +if (!cp_regs) +return -ENOMEM ; + +for (i =0 ; i < nump; i++) { +u64 val, pre_addr =0 ;
This is my mistake. The 'pre_addr' should be defined out of this 'for' loop. Or, you can remove all 'pre_addr' related statements, commercially available chips that have been tested cannot have such errors.
drivers/iommu/arm/arm-smmu-v3/arm-smmu-v3.c static void arm_smmu_device_iidr_probe(struct arm_smmu_device *smmu) · line 3826
Quoted 8 lines
drivers/iommu/arm/arm-smmu-v3/arm-smmu-v3.c +8
-0+ + val =readq_relaxed (cp_regs +32 * i); +if (!(val &ECMDQ_CP_PRESET )) { +iounmap (cp_regs); +dev_err (smmu->dev,"ecmdq control page %u is memory mode\n" , i); +return -EFAULT ; + } +
<---------------------------------------------
Review
Quoted 7 lines
(quoted diff) +7
-0+ if (i && ((val & ECMDQ_CP_ADDR) != (pre_addr + ECMDQ_CP_RRESET_SIZE))) { | + iounmap(cp_regs); | + dev_err(smmu->dev, "ecmdq_cp memory region is not contiguous\n"); | + return -EFAULT; | + } | + | + pre_addr = val & ECMDQ_CP_ADDR; |
<-------------------------------------------- feel free remove these
Quoted 1 line
(quoted diff) +1
-0+ }
Signature · 2 lines
Regards, Zhen Lei
PATCH v3 2/2 iommu/arm-smmu-v3: Ensure that a set of associated commands are inserted in the same ECMDQ
In reply to Tanmay JagdaleFrom: Zhen Lei <[email protected]>
The SYNC command only ensures that the command that precedes it in the same ECMDQ must be executed, but cannot synchronize the commands in other ECMDQs. If an unmap involves multiple commands, some commands are executed on one core, and the other commands are executed on another core. In this case, after the SYNC execution is complete, the execution of all preceded commands can not be ensured.
Prevent the process that performs a set of associated commands insertion from being migrated to other cores ensures that all commands are inserted into the same ECMDQ.
--- drivers/iommu/arm/arm-smmu-v3/arm-smmu-v3.c | 42 +++++++++++++++++---- 1 file changed, 35 insertions(+), 7 deletions(-)
drivers/iommu/arm/arm-smmu-v3/arm-smmu-v3.c +35 -7
@@ -248,6 +248,18 @@ static int queue_remove_raw(struct arm_smmu_queue *q, u64 *ent)return 0 ; } +static void arm_smmu_preempt_disable (struct arm_smmu_device *smmu) +{ +if (smmu->ecmdq_enabled) +preempt_disable (); +} + +static void arm_smmu_preempt_enable (struct arm_smmu_device *smmu) +{ +if (smmu->ecmdq_enabled) +preempt_enable (); +} +/* High-level queue accessors */ static int arm_smmu_cmdq_build_cmd (u64 *cmd,struct arm_smmu_cmdq_ent *ent) {
@@ -1229,12 +1241,15 @@ static void arm_smmu_sync_cd(struct arm_smmu_master *master, }; cmds.num =0 ; + +arm_smmu_preempt_disable (smmu);for (i =0 ; i < master->num_streams; i++) { cmd.cfgi.sid = master->streams[i].id;arm_smmu_cmdq_batch_add (smmu, &cmds, &cmd); }arm_smmu_cmdq_batch_submit (smmu, &cmds); +arm_smmu_preempt_enable (smmu); } static int arm_smmu_alloc_cd_leaf_table(struct arm_smmu_device *smmu,
@@ -1979,31 +1994,38 @@ arm_smmu_atc_inv_to_cmd(int ssid, unsigned long iova, size_t size,static int arm_smmu_atc_inv_master (struct arm_smmu_master *master) { -int i; +int i, ret;struct arm_smmu_cmdq_ent cmd;struct arm_smmu_cmdq_batch cmds; +struct arm_smmu_device *smmu = master->smmu;arm_smmu_atc_inv_to_cmd (IOMMU_NO_PASID ,0 ,0 , &cmd); cmds.num =0 ; + +arm_smmu_preempt_disable (smmu);for (i =0 ; i < master->num_streams; i++) { cmd.atc.sid = master->streams[i].id; -arm_smmu_cmdq_batch_add (master->smmu, &cmds, &cmd); +arm_smmu_cmdq_batch_add (smmu, &cmds, &cmd); } -return arm_smmu_cmdq_batch_submit (master->smmu, &cmds); + ret =arm_smmu_cmdq_batch_submit (smmu, &cmds); +arm_smmu_preempt_enable (smmu); + +return ret; }int arm_smmu_atc_inv_domain (struct arm_smmu_domain *smmu_domain,int ssid,unsigned long iova,size_t size) { -int i; +int i, ret;unsigned long flags;struct arm_smmu_cmdq_ent cmd;struct arm_smmu_master *master;struct arm_smmu_cmdq_batch cmds; +struct arm_smmu_device *smmu = smmu_domain->smmu; -if (!(smmu_domain->smmu->features &ARM_SMMU_FEAT_ATS )) +if (!(smmu->features &ARM_SMMU_FEAT_ATS ))return 0 ;/*
@@ -2027,6 +2049,7 @@ int arm_smmu_atc_inv_domain(struct arm_smmu_domain *smmu_domain, int ssid, cmds.num =0 ; +arm_smmu_preempt_disable (smmu);spin_lock_irqsave (&smmu_domain->devices_lock, flags);list_for_each_entry (master, &smmu_domain->devices, domain_head) {if (!master->ats_enabled)
@@ -2034,12 +2057,15 @@ int arm_smmu_atc_inv_domain(struct arm_smmu_domain *smmu_domain, int ssid,for (i =0 ; i < master->num_streams; i++) { cmd.atc.sid = master->streams[i].id; -arm_smmu_cmdq_batch_add (smmu_domain->smmu, &cmds, &cmd); +arm_smmu_cmdq_batch_add (smmu, &cmds, &cmd); } }spin_unlock_irqrestore (&smmu_domain->devices_lock, flags); -return arm_smmu_cmdq_batch_submit (smmu_domain->smmu, &cmds); + ret =arm_smmu_cmdq_batch_submit (smmu, &cmds); +arm_smmu_preempt_enable (smmu); + +return ret; }/* IO_PGTABLE API */
@@ -2104,6 +2130,7 @@ static void __arm_smmu_tlb_inv_range(struct arm_smmu_cmdq_ent *cmd, cmds.num =0 ; +arm_smmu_preempt_disable (smmu);while (iova < end) {if (smmu->features &ARM_SMMU_FEAT_RANGE_INV ) {/*
@@ -2135,6 +2162,7 @@ static void __arm_smmu_tlb_inv_range(struct arm_smmu_cmdq_ent *cmd, iova += inv_range; }arm_smmu_cmdq_batch_submit (smmu, &cmds); +arm_smmu_preempt_enable (smmu); } static void arm_smmu_tlb_inv_range_domain(unsigned long iova, size_t size,
Signature · 1 line
2.34.1
Quoted 9 lines · Tanmay Jagdale
Resending the patches by Zhen Lei <[email protected]> that add support for SMMU ECMDQ feature.
Tested this feature on a Marvell SoC by implementing a smmu-test driver. This test driver spawns a thread per CPU and each thread keeps sending map, table-walk and unmap requests for a fixed duration.
Using this test driver, we compared ECMDQ vs SMMU with software batching support and saw ~5% improvement with ECMDQ. Performance numbers are
This data is similar to the performance simulated by our EMU.
Quoted 13 lines
mentioned below:
Total Requests Average Requests Difference
Per CPU wrt ECMDQ
-----------------------------------------------------------------ECMDQ 239286381 2991079 CMDQ Batch Size 1 228232187 2852902 -4.62% CMDQ Batch Size 32 233465784 2918322 -2.43% CMDQ Batch Size 64 231679588 2895994 -3.18% CMDQ Batch Size 128 233189030 2914862 -2.55% CMDQ Batch Size 256 230965773 2887072 -3.48%
Quoted 4 lines
v2 --> v3:
1. Rebased on linux 6.9-rc5v1 --> v2:
Thanks.
Quoted 42 lines
1. Drop patch "iommu/arm-smmu-v3: Add
arm_smmu_ecmdq_issue_cmdlist()for non-shared ECMDQ" in v1
2. Drop patch "iommu/arm-smmu-v3: Add support for less than one ECMDQ per core" in v1
3. Replace rwlock with IPI to support lockless protection against the write operation to bit
'ERRACK' during error handling and the read operation to bit 'ERRACK'
during command insertion.
4. Standardize variable names.(quoted diff) +1
-1- struct arm_smmu_ecmdq *__percpu *ecmdq; + struct arm_smmu_ecmdq *__percpu *ecmdqs;5. Add member 'iobase' to struct
arm_smmu_deviceto record the start physical
address of the SMMU, to replace translation operation
(vmalloc_to_pfn(smmu->base)<<PAGE_SHIFT)(quoted diff) +1
-1+ phys_addr_t iobase; - smmu_dma_base = (vmalloc_to_pfn(smmu->base) << PAGE_SHIFT);6. Cancel below union. Whether ECMDQ is enabled is determined only based on '
ecmdq_enabled'.(quoted diff) +2
-4- union { - u32 nr_ecmdq; - u32 ecmdq_enabled; - }; + u32 nr_ecmdq; + bool ecmdq_enabled;7. Eliminate some sparse check warnings. For example.
(quoted diff) +1
-1- struct arm_smmu_ecmdq *ecmdq; + struct arm_smmu_ecmdq __percpu *ecmdq;Zhen Lei (2):
iommu/arm-smmu-v3: Add support for ECMDQ register mode iommu/arm-smmu-v3: Ensure that a set of associated commands are
inserted in the same ECMDQdrivers/iommu/arm/arm-smmu-v3/arm-smmu-v3.c | 261 +++++++++++++++++++- drivers/iommu/arm/arm-smmu-v3/arm-smmu-v3.h | 33 +++ 2 files changed, 286 insertions(+), 8 deletions(-)
Signature · 2 lines
Regards, Zhen Lei
Will Deacon
maintainerQuoted 14 lines · Tanmay Jagdale
Resending the patches by Zhen Lei <[email protected]> that add support for SMMU ECMDQ feature.
Tested this feature on a Marvell SoC by implementing a smmu-test driver. This test driver spawns a thread per CPU and each thread keeps sending map, table-walk and unmap requests for a fixed duration.
Using this test driver, we compared ECMDQ vs SMMU with software batching support and saw ~5% improvement with ECMDQ. Performance numbers are mentioned below:
Total Requests Average Requests Difference
Per CPU wrt ECMDQ
-----------------------------------------------------------------
Quoted 6 lines
ECMDQ 239286381 2991079 CMDQ Batch Size 1 228232187 2852902 -4.62% CMDQ Batch Size 32 233465784 2918322 -2.43% CMDQ Batch Size 64 231679588 2895994 -3.18% CMDQ Batch Size 128 233189030 2914862 -2.55% CMDQ Batch Size 256 230965773 2887072 -3.48%
These are pretty small improvements in a targetted micro-benchmark. Do you have any real-world numbers showing that this is worthwhile? For example, running something like netperf.
Will
Hi Will,
Quoted 22 lines · Will Deacon
Quoted 14 lines · Tanmay Jagdale
Resending the patches by Zhen Lei <[email protected]> that add support for SMMU ECMDQ feature.
Tested this feature on a Marvell SoC by implementing a smmu-test driver. This test driver spawns a thread per CPU and each thread keeps sending map, table-walk and unmap requests for a fixed duration.
Using this test driver, we compared ECMDQ vs SMMU with software batching support and saw ~5% improvement with ECMDQ. Performance numbers are mentioned below:
Total Requests Average Requests Difference
Per CPU wrt ECMDQ
-----------------------------------------------------------------Quoted 6 lines
ECMDQ 239286381 2991079 CMDQ Batch Size 1 228232187 2852902 -4.62% CMDQ Batch Size 32 233465784 2918322 -2.43% CMDQ Batch Size 64 231679588 2895994 -3.18% CMDQ Batch Size 128 233189030 2914862 -2.55% CMDQ Batch Size 256 230965773 2887072 -3.48%
Quoted 3 lines
These are pretty small improvements in a targetted micro-benchmark. Do you have any real-world numbers showing that this is worthwhile? For example, running something like netperf.
We are running benchmarks on the latest kernel with and without ECMDQ. We will share the performance numbers and observations here.
With Regards,
Tanmay
Quoted 7 lines
Will
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Quoted 6 lines · Tanmay Jagdale
Resending the patches by Zhen Lei <[email protected]> that add support for SMMU ECMDQ feature.
Tested this feature on a Marvell SoC by implementing a smmu-test driver. This test driver spawns a thread per CPU and each thread keeps sending map, table-walk and unmap requests for a fixed duration.
So this is not just measuring invalidation performance but basically the DMA API performance to do map/unmap operations? What is "batch size" ?
Does this HW support the range invalidation? How many invalidation commands does earch test cycle generate?
Quoted 9 lines
Total Requests Average Requests Difference
Per CPU wrt ECMDQ
-----------------------------------------------------------------ECMDQ 239286381 2991079 CMDQ Batch Size 1 228232187 2852902 -4.62% CMDQ Batch Size 32 233465784 2918322 -2.43% CMDQ Batch Size 64 231679588 2895994 -3.18% CMDQ Batch Size 128 233189030 2914862 -2.55% CMDQ Batch Size 256 230965773 2887072 -3.48%
If this is really 5% for a typical DMA API map/unmap cycle then that seems interesting to me.
If it is 5% for just the invalidation command then it is harder to say.
I'd suggest to present your results in terms of latency to do a dma API map/unmap cycle, and to show how the results scale as you add more threads. Does even 2 threads start to show a 4-5% gain?
Also, I'm wondering how ATS would interact, I think we have a head-of-line blocking issue with ATS.. Allowing ATS to progress concurrently with unrelated parallel invalidations may also be interesting, esepcially for multi-SVA workloads.
Jason