power: regulator: add AXP717 support
Subsystems (3)
cover power: regulator: add AXP717 support
The X-Powers AXP717 is a PMIC chip, controlled via I2C or RSB. It features four DC/DC converters and a number of linear regulators. Also it contains some charger and USB-C detection circuitry, though we don't use that in U-Boot. The PMIC is used on some newer Allwinner devices, for instance the Anbernic handheld gaming devices.
Add AXP717 support to the DM driven AXP regulator driver, and also an SPL version, as we need to program the DRAM voltage rail correctly before attempting to initialise the DRAM controller.
Cheers,
Ander
Andre Przywara (2):
power: pmic: sunxi: add AXP717 SPL driver
power: regulator: add AXP717 support
arch/arm/mach-sunxi/pmic_bus.c | 3 + board/sunxi/board.c | 2 +- drivers/power/Kconfig | 17 +++-- drivers/power/Makefile | 1 + drivers/power/axp717.c | 92 +++++++++++++++++++++++++ drivers/power/pmic/axp.c | 1 + drivers/power/regulator/axp_regulator.c | 28 ++++++++ include/axp_pmic.h | 1 + 8 files changed, 140 insertions(+), 5 deletions(-) create mode 100644 drivers/power/axp717.c
Signature · 1 line
2.35.8
PATCH 1/2 power: pmic: sunxi: add AXP717 SPL driver
On boards using the AXP717 PMIC, the DRAM rail is often not setup correctly at reset time, so we have to program the PMIC very early in the SPL, before running the DRAM initialisation.
Add a simple AXP717 PMIC driver that knows about the buck converters, so that we can set the voltage for the DRAM chips and the CPU cores.
--- arch/arm/mach-sunxi/pmic_bus.c | 3 ++ board/sunxi/board.c | 2 +- drivers/power/Kconfig | 17 +++++-- drivers/power/Makefile | 1 + drivers/power/axp717.c | 92 ++++++++++++++++++++++++++++++++++ 5 files changed, 110 insertions(+), 5 deletions(-) create mode 100644 drivers/power/axp717.c
arch/arm/mach-sunxi/pmic_bus.c +3 -0
@@ -19,6 +19,7 @@#define AXP152_I2C_ADDR 0x30#define AXP209_I2C_ADDR 0x34 +#define AXP717_I2C_ADDR 0x34#define AXP305_I2C_ADDR 0x36#define AXP313_I2C_ADDR 0x36
@@ -36,6 +37,8 @@ static int pmic_i2c_address(void)return AXP305_I2C_ADDR ;if (IS_ENABLED (CONFIG_AXP313_POWER ))return AXP313_I2C_ADDR ; +if (IS_ENABLED (CONFIG_AXP717_POWER )) +return AXP717_I2C_ADDR ;/* Other AXP2xx and AXP8xx variants */ return AXP209_I2C_ADDR ;
board/sunxi/board.c +1 -1
@@ -563,7 +563,7 @@ void sunxi_board_init(void)#if definedCONFIG_AXP152_POWER || definedCONFIG_AXP209_POWER || \ definedCONFIG_AXP221_POWER || definedCONFIG_AXP305_POWER || \ definedCONFIG_AXP809_POWER || definedCONFIG_AXP818_POWER || \ - definedCONFIG_AXP313_POWER + definedCONFIG_AXP313_POWER || definedCONFIG_AXP717_POWER power_failed =axp_init ();if (IS_ENABLED (CONFIG_AXP_DISABLE_BOOT_ON_POWERON ) && !power_failed) {
drivers/power/Kconfig +13 -4
@@ -109,6 +109,13 @@ config AXP313_POWER Select this to enable support for the AXP313 PMIC found on some H616 boards. +config AXP717_POWER + bool "axp717 pmic support" + select AXP_PMIC_BUS + select CMD_POWEROFF + ---help--- + Select this to enable support for the AXP717 PMIC found on some boards. + config AXP809_POWER bool "axp809 pmic support" depends on MACH_SUN9I
@@ -151,10 +158,11 @@ config AXP_DCDC1_VOLT config AXP_DCDC2_VOLT int "axp pmic dcdc2 voltage" - depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER || AXP313_POWER + depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER || AXP313_POWER || AXP717_POWER default 900 if AXP818_POWER default 1400 if AXP152_POWER || AXP209_POWER default 1000 if AXP313_POWER + default 1000 if AXP717_POWER default 1200 if MACH_SUN6I default 1100 if MACH_SUN8I default 0 if MACH_SUN9I
@@ -167,11 +175,11 @@ config AXP_DCDC2_VOLT On A80 boards dcdc2 powers the GPU and can be left off. On A83T boards dcdc2 is used for VDD-CPUA(cluster 0) and should be 0.9V. On R40 boards dcdc2 is VDD-CPU and should be 1.1V - On boards using the AXP313 it's often VDD-CPU. + On boards using the AXP313 or AXP717 it's often VDD-CPU. config AXP_DCDC3_VOLT int "axp pmic dcdc3 voltage" - depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER || AXP313_POWER + depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER || AXP313_POWER || AXP717_POWER default 900 if AXP809_POWER || AXP818_POWER default 1500 if AXP152_POWER default 1250 if AXP209_POWER
@@ -188,7 +196,8 @@ config AXP_DCDC3_VOLT On A80 boards dcdc3 is used for VDD-CPUA(cluster 0) and should be 0.9V. On A83T boards dcdc3 is used for VDD-CPUB(cluster 1) and should be 0.9V. On R40 boards dcdc3 is VDD-SYS and VDD-GPU and should be 1.1V. - On boards using the AXP313 it's often VDD-DRAM and should be 1.1V for LPDDR4. + On boards using the AXP313 or AXP717 it's often VDD-DRAM and should + be 1.1V for LPDDR4. config AXP_DCDC4_VOLT int "axp pmic dcdc4 voltage"
drivers/power/Makefile +1 -0
@@ -13,6 +13,7 @@ obj-$(CONFIG_AXP209_POWER) += axp209.o obj-$(CONFIG_AXP221_POWER) += axp221.o obj-$(CONFIG_AXP305_POWER) += axp305.o obj-$(CONFIG_AXP313_POWER) += axp313.o +obj-$(CONFIG_AXP717_POWER) += axp717.o obj-$(CONFIG_AXP809_POWER) += axp809.o obj-$(CONFIG_AXP818_POWER) += axp818.o obj-$(CONFIG_EXYNOS_TMU) += exynos-tmu.o
drivers/power/axp717.c new file +92 -0
92 lines not on this page · raw message
Signature · 1 line
2.35.8
Re: [PATCH 1/2] power: pmic: sunxi: add AXP717 SPL driver
Quoted 228 lines · Andre Przywara
On boards using the AXP717 PMIC, the DRAM rail is often not setup correctly at reset time, so we have to program the PMIC very early in the SPL, before running the DRAM initialisation.
Add a simple AXP717 PMIC driver that knows about the buck converters, so that we can set the voltage for the DRAM chips and the CPU cores.
Signed-off-by Andre Przywara <[email protected]>--- arch/arm/mach-sunxi/pmic_bus.c | 3 ++ board/sunxi/board.c | 2 +- drivers/power/Kconfig | 17 +++++-- drivers/power/Makefile | 1 + drivers/power/axp717.c | 92 ++++++++++++++++++++++++++++++++++ 5 files changed, 110 insertions(+), 5 deletions(-) create mode 100644 drivers/power/axp717.carch/arm/mach-sunxi/pmic_bus.c +3
-0@@ -19,6 +19,7 @@#define AXP152_I2C_ADDR 0x30#define AXP209_I2C_ADDR 0x34 +#define AXP717_I2C_ADDR 0x34#define AXP305_I2C_ADDR 0x36#define AXP313_I2C_ADDR 0x36@@ -36,6 +37,8 @@ static int pmic_i2c_address(void)return AXP305_I2C_ADDR ;if (IS_ENABLED (CONFIG_AXP313_POWER ))return AXP313_I2C_ADDR ; +if (IS_ENABLED (CONFIG_AXP717_POWER )) +return AXP717_I2C_ADDR ;/* Other AXP2xx and AXP8xx variants */ return AXP209_I2C_ADDR ;board/sunxi/board.c +1
-1@@ -563,7 +563,7 @@ void sunxi_board_init(void)#if definedCONFIG_AXP152_POWER || definedCONFIG_AXP209_POWER || \ definedCONFIG_AXP221_POWER || definedCONFIG_AXP305_POWER || \ definedCONFIG_AXP809_POWER || definedCONFIG_AXP818_POWER || \ - definedCONFIG_AXP313_POWER + definedCONFIG_AXP313_POWER || definedCONFIG_AXP717_POWER power_failed =axp_init ();if (IS_ENABLED (CONFIG_AXP_DISABLE_BOOT_ON_POWERON ) && !power_failed) {drivers/power/Kconfig +7
-1@@ -109,6 +109,13 @@ config AXP313_POWER Select this to enable support for the AXP313 PMIC found on some H616 boards. +config AXP717_POWER + bool "axp717 pmic support" + select AXP_PMIC_BUS + select CMD_POWEROFF + ---help--- + Select this to enable support for the AXP717 PMIC found on some boards. + config AXP809_POWER bool "axp809 pmic support" depends on MACH_SUN9I@@ -151,10 +158,11 @@ config AXP_DCDC1_VOLT config AXP_DCDC2_VOLT int "axp pmic dcdc2 voltage" - depends on AXP152_POWER || AXP209_POWER || AXP221_POWER ||
AXP809_POWER||AXP818_POWER||AXP313_POWERdrivers/power/Kconfig +1
-0+ depends on AXP152_POWER || AXP209_POWER || AXP221_POWER ||
AXP809_POWER||AXP818_POWER||AXP313_POWER||AXP717_POWERdrivers/power/Kconfig +1
-0default 900 if AXP818_POWER default 1400 if AXP152_POWER || AXP209_POWER default 1000 if AXP313_POWER + default 1000 if AXP717_POWER default 1200 if MACH_SUN6I default 1100 if MACH_SUN8I default 0 if MACH_SUN9I@@ -167,11 +175,11 @@ config AXP_DCDC2_VOLT On A80 boards dcdc2 powers the GPU and can be left off. On A83T boards dcdc2 is used for VDD-CPUA(cluster 0) and should be0.9V.
drivers/power/Kconfig +1
-2On R40 boards dcdc2 is VDD-CPU and should be 1.1V - On boards using the AXP313 it's often VDD-CPU. + On boards using the AXP313 or AXP717 it's often VDD-CPU. config AXP_DCDC3_VOLT int "axp pmic dcdc3 voltage" - depends on AXP152_POWER || AXP209_POWER || AXP221_POWER ||
AXP809_POWER||AXP818_POWER||AXP313_POWERdrivers/power/Kconfig +1
-0+ depends on AXP152_POWER || AXP209_POWER || AXP221_POWER ||
AXP809_POWER||AXP818_POWER||AXP313_POWER||AXP717_POWERdrivers/power/Kconfig +0
-0default 900 if AXP809_POWER || AXP818_POWER default 1500 if AXP152_POWER default 1250 if AXP209_POWER@@ -188,7 +196,8 @@ config AXP_DCDC3_VOLT On A80 boards dcdc3 is used for VDD-CPUA(cluster 0) and should be0.9V.
On A83T boards dcdc3 is used for VDD-CPUB(cluster 1) and should be
0.9V.drivers/power/Kconfig +0
-1On R40 boards dcdc3 is VDD-SYS and VDD-GPU and should be 1.1V. - On boards using the AXP313 it's often VDD-DRAM and should be 1.1V forLPDDR4.
drivers/power/Kconfig +2
-0+ On boards using the AXP313 or AXP717 it's often VDD-DRAM and should + be 1.1V for LPDDR4. config AXP_DCDC4_VOLT int "axp pmic dcdc4 voltage"drivers/power/Makefile +1
-0@@ -13,6 +13,7 @@ obj-$(CONFIG_AXP209_POWER) += axp209.o obj-$(CONFIG_AXP221_POWER) += axp221.o obj-$(CONFIG_AXP305_POWER) += axp305.o obj-$(CONFIG_AXP313_POWER) += axp313.o +obj-$(CONFIG_AXP717_POWER) += axp717.o obj-$(CONFIG_AXP809_POWER) += axp809.o obj-$(CONFIG_AXP818_POWER) += axp818.o obj-$(CONFIG_EXYNOS_TMU) += exynos-tmu.odrivers/power/axp717.c new file +81
-0@@ -0,0 +1,92 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* AXP717 SPL driver +* (C) Copyright 2024 Arm Ltd. +*/ + +#include <common.h> +#include <command.h> +#include <errno.h> +#include <asm/arch/pmic_bus.h> +#include <axp_pmic.h> + +enum axp717_reg { +AXP717_CHIP_VERSION =0x3 , +AXP717_SHUTDOWN =0x27 , +AXP717_OUTPUT_CTRL1 =0x80 , +AXP717_DCDC1_VOLTAGE =0x83 , +}; + +#define AXP717_CHIP_VERSION_MASK 0xc8 +#define AXP717_DCDC_1220MV_OFFSET 71 +#define AXP717_POWEROFF (1U << 0) +#define DCDC_DVM_ENABLE (1U << 7) + +static u8 axp_mvolt_to_cfg (int mvolt,int min,int max,int div) +{ +if (mvolt < min) + mvolt = min; +else if (mvolt > max) + mvolt = max; + +return (mvolt - min) / div; +} + +static int axp_set_dcdc (int dcdc_num,unsigned int mvolt) +{ +int ret; +u8 cfg =DCDC_DVM_ENABLE ; + +if (dcdc_num <1 || dcdc_num >3 ) +return -EINVAL ; + +if (mvolt >=1220 ) + cfg |=AXP717_DCDC_1220MV_OFFSET + +axp_mvolt_to_cfg (mvolt,1220 , + dcdc_num ==3 ?1840 :1540 ,20 ); +else + cfg |=axp_mvolt_to_cfg (mvolt,500 ,1200 ,10 ); + +if (mvolt ==0 ) +return pmic_bus_clrbits (AXP717_OUTPUT_CTRL1 , +1U << (dcdc_num -1 )); + + ret =pmic_bus_write (AXP717_DCDC1_VOLTAGE + dcdc_num -1 , cfg); +if (ret) +return ret; + +return pmic_bus_setbits (AXP717_OUTPUT_CTRL1 ,1U << (dcdc_num -1 )); +} + +int axp_set_dcdc1 (unsigned int mvolt) +{ +return axp_set_dcdc (1 , mvolt); +} + +int axp_set_dcdc2 (unsigned int mvolt) +{ +return axp_set_dcdc (2 , mvolt); +} + +int axp_set_dcdc3 (unsigned int mvolt) +{ +return axp_set_dcdc (3 , mvolt); +} + +int axp_init (void ) +{ +return pmic_bus_init (); +} + +#if !CONFIG_IS_ENABLED(ARM_PSCI_FW) &&!IS_ENABLED(CONFIG_SYSRESET_CMD_POWEROFF)
+intdo_poweroff(struct cmd_tbl *cmdtp, int flag, int argc, char *const argv[])drivers/power/axp717.c new file +10
-0+{ +pmic_bus_setbits (AXP717_SHUTDOWN ,AXP717_POWEROFF ); + +/* infinite loop during shutdown */ +while (1 ) {} + +/* not reached */ +return 0 ; +} +#endif Signature · 1 line
2.35.8
Confirmed working on H700 board with AXP717 PMIC and LPDDR4 DRAM controller (Anbernic RG35XX-H) and verified I2C address and registers from datasheet.
Regards,
Ryan
PATCH 2/2 power: regulator: add AXP717 support
In reply to Andre PrzywaraThe X-Powers AXP717 is a PMIC with four buck converters and a number of LDOs, one of which is actually fixed (so not modelled here).
Add the compatible string and the respective regulator ranges to allow drivers to adjust voltages.
--- drivers/power/pmic/axp.c | 1 + drivers/power/regulator/axp_regulator.c | 28 +++++++++++++++++++++++++ include/axp_pmic.h | 1 + 3 files changed, 30 insertions(+)
drivers/power/pmic/axp.c +1 -0
@@ -89,6 +89,7 @@ static const struct udevice_id axp_pmic_ids[] = { { .compatible = "x-powers,axp221", .data = AXP221_ID }, { .compatible = "x-powers,axp223", .data = AXP223_ID }, { .compatible = "x-powers,axp313a", .data = AXP313_ID }, + { .compatible = "x-powers,axp717", .data = AXP717_ID }, { .compatible = "x-powers,axp803", .data = AXP803_ID }, { .compatible = "x-powers,axp806", .data = AXP806_ID }, { .compatible = "x-powers,axp809", .data = AXP809_ID },
drivers/power/regulator/axp_regulator.c +28 -0
@@ -189,6 +189,33 @@ static const struct axp_regulator_plat axp313_regulators[] = { { } }; +/* +* The "dcdc2" regulator has another range, beyond 1.54V up to 3.4V, in +* steps of 100mV. We cannot model this easily, but also don't need that, +* since it's typically only used for lower voltages anyway, so just ignore it. +*/ +static const struct axp_regulator_plat axp717_regulators[] = { + {"dcdc1" ,0x80 ,BIT (0 ),0x83 ,0x7f ,500 ,1540 ,10 ,70 }, + {"dcdc2" ,0x80 ,BIT (1 ),0x84 ,0x7f ,500 ,1540 ,10 ,70 }, + {"dcdc3" ,0x80 ,BIT (2 ),0x85 ,0x7f ,500 ,1840 ,10 ,70 }, + {"dcdc4" ,0x80 ,BIT (3 ),0x86 ,0x7f ,1000 ,3700 ,100 ,NA }, + {"aldo1" ,0x90 ,BIT (0 ),0x93 ,0x1f ,500 ,3500 ,100 ,NA }, + {"aldo2" ,0x90 ,BIT (1 ),0x94 ,0x1f ,500 ,3500 ,100 ,NA }, + {"aldo3" ,0x90 ,BIT (2 ),0x95 ,0x1f ,500 ,3500 ,100 ,NA }, + {"aldo4" ,0x90 ,BIT (3 ),0x96 ,0x1f ,500 ,3500 ,100 ,NA }, + {"bldo1" ,0x90 ,BIT (4 ),0x97 ,0x1f ,500 ,3500 ,100 ,NA }, + {"bldo2" ,0x90 ,BIT (5 ),0x98 ,0x1f ,500 ,3500 ,100 ,NA }, + {"bldo3" ,0x90 ,BIT (6 ),0x99 ,0x1f ,500 ,3500 ,100 ,NA }, + {"bldo4" ,0x90 ,BIT (7 ),0x9a ,0x1f ,500 ,3500 ,100 ,NA }, + {"cldo1" ,0x91 ,BIT (0 ),0x9b ,0x1f ,500 ,3500 ,100 ,NA }, + {"cldo2" ,0x91 ,BIT (1 ),0x9c ,0x1f ,500 ,3500 ,100 ,NA }, + {"cldo3" ,0x91 ,BIT (2 ),0x9d ,0x1f ,500 ,3500 ,100 ,NA }, + {"cldo4" ,0x91 ,BIT (3 ),0x9e ,0x1f ,500 ,3500 ,100 ,NA }, + {"cpusldo" ,0x91 ,BIT (4 ),0x9f ,0x1f ,500 ,1400 ,50 ,NA }, + {" boost" ,0x19 ,BIT (4 ),0x1e ,0xf0 ,4550 ,5510 ,64 ,NA }, + { } +}; +static const struct axp_regulator_plat axp803_regulators[] = { {"dcdc1" ,0x10 ,BIT (0 ),0x20 ,0x1f ,1600 ,3400 ,100 ,NA }, {"dcdc2" ,0x10 ,BIT (1 ),0x21 ,0x7f ,500 ,1300 ,10 ,70 },
@@ -291,6 +318,7 @@ static const struct axp_regulator_plat *const axp_regulators[] = { [AXP221_ID] = axp22x_regulators, [AXP223_ID] = axp22x_regulators, [AXP313_ID] = axp313_regulators, + [AXP717_ID] = axp717_regulators, [AXP803_ID] = axp803_regulators, [AXP806_ID] = axp806_regulators, [AXP809_ID] = axp809_regulators,
include/axp_pmic.h +1 -0
@@ -33,6 +33,7 @@ enum {AXP221_ID ,AXP223_ID ,AXP313_ID , +AXP717_ID ,AXP803_ID ,AXP806_ID , AXP809_ID,
Signature · 1 line
2.35.8
Quoted 90 lines · Andre Przywara
The X-Powers AXP717 is a PMIC with four buck converters and a number of LDOs, one of which is actually fixed (so not modelled here).
Add the compatible string and the respective regulator ranges to allow drivers to adjust voltages.
Signed-off-by Andre Przywara <[email protected]>--- drivers/power/pmic/axp.c | 1 + drivers/power/regulator/axp_regulator.c | 28 +++++++++++++++++++++++++ include/axp_pmic.h | 1 + 3 files changed, 30 insertions(+)drivers/power/pmic/axp.c +1
-0@@ -89,6 +89,7 @@ static const struct udevice_id axp_pmic_ids[] = { { .compatible = "x-powers,axp221", .data = AXP221_ID }, { .compatible = "x-powers,axp223", .data = AXP223_ID }, { .compatible = "x-powers,axp313a", .data = AXP313_ID }, + { .compatible = "x-powers,axp717", .data = AXP717_ID }, { .compatible = "x-powers,axp803", .data = AXP803_ID }, { .compatible = "x-powers,axp806", .data = AXP806_ID }, { .compatible = "x-powers,axp809", .data = AXP809_ID },drivers/power/regulator/axp_regulator.c +4
-0@@ -189,6 +189,33 @@ static const struct axp_regulator_plat axp313_regulators[] = { { } }; +/* +* The "dcdc2" regulator has another range, beyond 1.54V up to 3.4V, in +* steps of 100mV. We cannot model this easily, but also don't need that, +* since it's typically only used for lower voltages anyway, so just ignore it.
+ */drivers/power/regulator/axp_regulator.c +23
-0+static const struct axp_regulator_plat axp717_regulators[] = { + {"dcdc1" ,0x80 ,BIT (0 ),0x83 ,0x7f ,500 ,1540 ,10 ,70 }, + {"dcdc2" ,0x80 ,BIT (1 ),0x84 ,0x7f ,500 ,1540 ,10 ,70 }, + {"dcdc3" ,0x80 ,BIT (2 ),0x85 ,0x7f ,500 ,1840 ,10 ,70 }, + {"dcdc4" ,0x80 ,BIT (3 ),0x86 ,0x7f ,1000 ,3700 ,100 ,NA }, + {"aldo1" ,0x90 ,BIT (0 ),0x93 ,0x1f ,500 ,3500 ,100 ,NA }, + {"aldo2" ,0x90 ,BIT (1 ),0x94 ,0x1f ,500 ,3500 ,100 ,NA }, + {"aldo3" ,0x90 ,BIT (2 ),0x95 ,0x1f ,500 ,3500 ,100 ,NA }, + {"aldo4" ,0x90 ,BIT (3 ),0x96 ,0x1f ,500 ,3500 ,100 ,NA }, + {"bldo1" ,0x90 ,BIT (4 ),0x97 ,0x1f ,500 ,3500 ,100 ,NA }, + {"bldo2" ,0x90 ,BIT (5 ),0x98 ,0x1f ,500 ,3500 ,100 ,NA }, + {"bldo3" ,0x90 ,BIT (6 ),0x99 ,0x1f ,500 ,3500 ,100 ,NA }, + {"bldo4" ,0x90 ,BIT (7 ),0x9a ,0x1f ,500 ,3500 ,100 ,NA }, + {"cldo1" ,0x91 ,BIT (0 ),0x9b ,0x1f ,500 ,3500 ,100 ,NA }, + {"cldo2" ,0x91 ,BIT (1 ),0x9c ,0x1f ,500 ,3500 ,100 ,NA }, + {"cldo3" ,0x91 ,BIT (2 ),0x9d ,0x1f ,500 ,3500 ,100 ,NA }, + {"cldo4" ,0x91 ,BIT (3 ),0x9e ,0x1f ,500 ,3500 ,100 ,NA }, + {"cpusldo" ,0x91 ,BIT (4 ),0x9f ,0x1f ,500 ,1400 ,50 ,NA }, + {" boost" ,0x19 ,BIT (4 ),0x1e ,0xf0 ,4550 ,5510 ,64 ,NA }, + { } +}; +static const struct axp_regulator_plat axp803_regulators[] = { {"dcdc1" ,0x10 ,BIT (0 ),0x20 ,0x1f ,1600 ,3400 ,100 ,NA }, {"dcdc2" ,0x10 ,BIT (1 ),0x21 ,0x7f ,500 ,1300 ,10 ,70 },@@ -291,6 +318,7 @@ static const struct axp_regulator_plat *const axp_regulators[] = { [AXP221_ID] = axp22x_regulators, [AXP223_ID] = axp22x_regulators, [AXP313_ID] = axp313_regulators, + [AXP717_ID] = axp717_regulators, [AXP803_ID] = axp803_regulators, [AXP806_ID] = axp806_regulators,drivers/power/regulator/axp_regulator.c +0
-0[AXP809_ID] = axp809_regulators,include/axp_pmic.h +1
-0@@ -33,6 +33,7 @@ enum {AXP221_ID ,AXP223_ID ,AXP313_ID , +AXP717_ID ,AXP803_ID ,AXP806_ID , AXP809_ID,Signature · 1 line
2.35.8
Confirmed working on H700 board with AXP717 PMIC and LPDDR4 DRAM controller (Anbernic RG35XX-H). Registers and voltage ranges confirmed from datasheet.
Regards,
Ryan