FAILED: patch "[PATCH] arm64: dts: qcom: sa8155p-adp: fix SDHC2 CD pin configuration" failed to apply to 6.1-stable tree

The patch below does not apply to the 6.1-stable tree.
If someone wants it applied there, or to any other stable or longterm tree, then please email the backport, including the original git commit id to <[email protected]>.

To reproduce the conflict and resubmit, you may use the following commands:

git fetch https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/ linux-6.1.y
git checkout FETCH_HEAD
git cherry-pick -x 819fe8c96a5172dfd960e5945e8f00f8fed32953
# <resolve conflicts, build, test, etc.>
git commit -s
git send-email --to '<[email protected]>' --in-reply-to '2024051326-filter-stoplight-c8cc@gregkh' --subject-prefix 'PATCH 6.1.y' HEAD^..

Possible dependencies:

819fe8c96a51 ("arm64: dts: qcom: sa8155p-adp: fix SDHC2 CD pin configuration") 028fe09cda0a ("arm64: dts: qcom: sm8150: align TLMM pin configuration with DT schema")

thanks,

greg k-h

------------------ original commit in Linus's tree ------------------

From 819fe8c96a5172dfd960e5945e8f00f8fed32953 Mon Sep 17 00:00:00 2001
From: Volodymyr Babchuk <[email protected]>
Date: Fri, 12 Apr 2024 19:03:25 +0000
Subject: [PATCH] arm64: dts: qcom: sa8155p-adp: fix SDHC2 CD pin configuration

There are two issues with SDHC2 configuration for SA8155P-ADP, which prevent use of SDHC2 and causes issues with ethernet:

- Card Detect pin for SHDC2 on SA8155P-ADP is connected to gpio4 of PMM8155AU_1, not to SoC itself. SoC's gpio4 is used for DWMAC TX. If sdhc driver probes after dwmac driver, it reconfigures gpio4 and this breaks Ethernet MAC.

- pinctrl configuration mentions gpio96 as CD pin. It seems it was copied from some SM8150 example, because as mentioned above, correct CD pin is gpio4 on PMM8155AU_1.

This patch fixes both mentioned issues by providing correct pin handle and pinctrl configuration.

index 5e4287f8c8cd..b2cf2c988336 100644
@@ -367,6 +367,16 @@ queue0 {
 	};
 };
 
+&pmm8155au_1_gpios {
+	pmm8155au_1_sdc2_cd: sdc2-cd-default-state {
+		pins = "gpio4";
+		function = "normal";
+		input-enable;
+		bias-pull-up;
+		power-source = <0>;
+	};
+};
+
 &qupv3_id_1 {
 	status = "okay";
 };

@@ -384,10 +394,10 @@ &remoteproc_cdsp {
 &sdhc_2 {
 	status = "okay";
 
-	cd-gpios = <&tlmm 4 GPIO_ACTIVE_LOW>;
+	cd-gpios = <&pmm8155au_1_gpios 4 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&sdc2_on>;
-	pinctrl-1 = <&sdc2_off>;
+	pinctrl-0 = <&sdc2_on &pmm8155au_1_sdc2_cd>;
+	pinctrl-1 = <&sdc2_off &pmm8155au_1_sdc2_cd>;
 	vqmmc-supply = <&vreg_l13c_2p96>; /* IO line power */
 	vmmc-supply = <&vreg_l17a_2p96>;  /* Card power line */
 	bus-width = <4>;

@@ -505,13 +515,6 @@ data-pins {
 			bias-pull-up;		/* pull up */
 			drive-strength = <16>;	/* 16 MA */
 		};
-
-		sd-cd-pins {
-			pins = "gpio96";
-			function = "gpio";
-			bias-pull-up;		/* pull up */
-			drive-strength = <2>;	/* 2 MA */
-		};
 	};
 
 	sdc2_off: sdc2-off-state {

@@ -532,13 +535,6 @@ data-pins {
 			bias-pull-up;		/* pull up */
 			drive-strength = <2>;	/* 2 MA */
 		};
-
-		sd-cd-pins {
-			pins = "gpio96";
-			function = "gpio";
-			bias-pull-up;		/* pull up */
-			drive-strength = <2>;	/* 2 MA */
-		};
 	};
 
 	usb2phy_ac_en1_default: usb2phy-ac-en1-default-state {