Skip to contentSkip to conversation

PCI: microchip: Fixes and clean-ups

PATCH Applied [email protected] 3 participants 10 messages Jul 28, 2023 – May 30, 2024

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

v3 cover PCI: microchip: Fixes and clean-ups

From: Daire McNamara <[email protected]>

This patch series contains fixes and clean-ups for the Microchip PolarFire SoC PCIe driver

These patches are extracted from the link below to separate them from the outbound and inbound range handling which is taking considerable time.

Resending with correct e-mail address list

These patches are regenerated on v6.5-rc3.

Main changes from v2:
- Reworked "Gather MSI information..." as suggested by Bjorn
- merged 'Gather MSI Information..." and "Rename and refactor" as suggested by Bjorn
- Re-generated on v6.5-rc3

Main Changes from v1:
- Dropped "Remove cast warning for devm_add_action_or_reset()". This has been overtaken by a patch series from Krzysztof Wilczynski.
- Improved the comment for "Enable building driver as a module" to clarify what enables building the driver as a module.
- Split "Gather MSI information from hardware config registers", for clarity, into:
- "Gather MSI information from hardware config registers" purely changing the of source of MSI-related information (Num MSIs and MSI address) from #defines (which can be incorrect) to FPGA configuration registers (which is the ultimate source of truth), and a
- "Rename and refactor ..." patch as a function's code is now clearly unrelated to its current name.

cc Conor Dooley <[email protected]>
cc Lorenzo Pieralisi <[email protected]>
cc "Krzysztof Wilczyński" <[email protected]>
cc Rob Herring <[email protected]>
cc Bjorn Helgaas <[email protected]>

Daire McNamara (8):
PCI: microchip: Correct the DED and SEC interrupt bit offsets
PCI: microchip: Enable building driver as a module
PCI: microchip: Align register, offset, and mask names with hw docs
PCI: microchip: Enable event handlers to access bridge and ctrl ptrs
PCI: microchip: Clean up initialisation of interrupts
PCI: microchip: Gather MSI information from hardware config registers
PCI: microchip: Re-partition code between probe() and init()

 drivers/pci/controller/Kconfig               |   2 +-
 drivers/pci/controller/pcie-microchip-host.c | 393 +++++++++++--------
 2 files changed, 233 insertions(+), 162 deletions(-)

base-commit: 6eaae198076080886b9e7d57f4ae06fa782f90ef

Signature · 1 line
2.25.1
#1 lore raw

PATCH v3 1/7 PCI: microchip: Correct the DED and SEC interrupt bit offsets

From: Daire McNamara <[email protected]>

The SEC and DED interrupt bits were the wrong way round so the SEC interrupt handler attempted to mask, unmask, and clear the DED interrupt and vice versa. Correct the bit offsets so each interrupt handler operates properly.

Fixes 6f15a9c9f941 ("PCI: microchip: Add Microchip PolarFire PCIe controller driver")
---
 drivers/pci/controller/pcie-microchip-host.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)
drivers/pci/controller/pcie-microchip-host.c +4 -4
index 5e710e485464..dd5245904c87 100644
@@ -167,12 +167,12 @@
 #define EVENT_PCIE_DLUP_EXIT			2
 #define EVENT_SEC_TX_RAM_SEC_ERR		3
 #define EVENT_SEC_RX_RAM_SEC_ERR		4
-#define EVENT_SEC_AXI2PCIE_RAM_SEC_ERR		5
-#define EVENT_SEC_PCIE2AXI_RAM_SEC_ERR		6
+#define EVENT_SEC_PCIE2AXI_RAM_SEC_ERR		5
+#define EVENT_SEC_AXI2PCIE_RAM_SEC_ERR		6
 #define EVENT_DED_TX_RAM_DED_ERR		7
 #define EVENT_DED_RX_RAM_DED_ERR		8
-#define EVENT_DED_AXI2PCIE_RAM_DED_ERR		9
-#define EVENT_DED_PCIE2AXI_RAM_DED_ERR		10
+#define EVENT_DED_PCIE2AXI_RAM_DED_ERR		9
+#define EVENT_DED_AXI2PCIE_RAM_DED_ERR		10
 #define EVENT_LOCAL_DMA_END_ENGINE_0		11
 #define EVENT_LOCAL_DMA_END_ENGINE_1		12
 #define EVENT_LOCAL_DMA_ERROR_ENGINE_0		13
Signature · 1 line
2.25.1
#2 lore raw

PATCH v3 2/7 PCI: microchip: Enable building driver as a module

In reply to [email protected]

From: Daire McNamara <[email protected]>

Enable building driver as a module. The expected use case is the driver is built as a module, is installed when needed, and cannot be removed once installed.

The driver has .suppress_bind_attrs set to true.

---
 drivers/pci/controller/Kconfig               | 2 +-
 drivers/pci/controller/pcie-microchip-host.c | 1 +
 2 files changed, 2 insertions(+), 1 deletion(-)
drivers/pci/controller/Kconfig +1 -1
index 8d49bad7f847..f4ad0e9cca45 100644
@@ -217,7 +217,7 @@ config PCIE_MT7621
 	  This selects a driver for the MediaTek MT7621 PCIe Controller.
 
 config PCIE_MICROCHIP_HOST
-	bool "Microchip AXI PCIe controller"
+	tristate "Microchip AXI PCIe controller"
 	depends on PCI_MSI && OF
 	select PCI_HOST_COMMON
 	help
drivers/pci/controller/pcie-microchip-host.c +1 -0
index dd5245904c87..5c89caaab8c9 100644
@@ -1135,5 +1135,6 @@ static struct platform_driver mc_pcie_driver = {
 };
 
 builtin_platform_driver(mc_pcie_driver);
+MODULE_LICENSE("GPL");
 MODULE_DESCRIPTION("Microchip PCIe host controller driver");
 MODULE_AUTHOR("Daire McNamara <[email protected]>");
Signature · 1 line
2.25.1
#3 lore raw

PATCH v3 3/7 PCI: microchip: Align register, offset, and mask names with hw docs

In reply to [email protected]

From: Daire McNamara <[email protected]>

Minor re-organisation so that macros representing registers ascend in numerical order and use the same names as their hardware documentation. Removed registers not used by the driver.

---
 drivers/pci/controller/pcie-microchip-host.c | 122 +++++++++----------
 1 file changed, 60 insertions(+), 62 deletions(-)
drivers/pci/controller/pcie-microchip-host.c +60 -62
index 5c89caaab8c9..30153fd1a2b3 100644
@@ -30,66 +30,7 @@
 #define MC_PCIE_BRIDGE_ADDR			(MC_PCIE1_BRIDGE_ADDR)
 #define MC_PCIE_CTRL_ADDR			(MC_PCIE1_CTRL_ADDR)
 
-/* PCIe Controller Phy Regs */
-#define SEC_ERROR_CNT				0x20
-#define DED_ERROR_CNT				0x24
-#define SEC_ERROR_INT				0x28
-#define  SEC_ERROR_INT_TX_RAM_SEC_ERR_INT	GENMASK(3, 0)
-#define  SEC_ERROR_INT_RX_RAM_SEC_ERR_INT	GENMASK(7, 4)
-#define  SEC_ERROR_INT_PCIE2AXI_RAM_SEC_ERR_INT	GENMASK(11, 8)
-#define  SEC_ERROR_INT_AXI2PCIE_RAM_SEC_ERR_INT	GENMASK(15, 12)
-#define  NUM_SEC_ERROR_INTS			(4)
-#define SEC_ERROR_INT_MASK			0x2c
-#define DED_ERROR_INT				0x30
-#define  DED_ERROR_INT_TX_RAM_DED_ERR_INT	GENMASK(3, 0)
-#define  DED_ERROR_INT_RX_RAM_DED_ERR_INT	GENMASK(7, 4)
-#define  DED_ERROR_INT_PCIE2AXI_RAM_DED_ERR_INT	GENMASK(11, 8)
-#define  DED_ERROR_INT_AXI2PCIE_RAM_DED_ERR_INT	GENMASK(15, 12)
-#define  NUM_DED_ERROR_INTS			(4)
-#define DED_ERROR_INT_MASK			0x34
-#define ECC_CONTROL				0x38
-#define  ECC_CONTROL_TX_RAM_INJ_ERROR_0		BIT(0)
-#define  ECC_CONTROL_TX_RAM_INJ_ERROR_1		BIT(1)
-#define  ECC_CONTROL_TX_RAM_INJ_ERROR_2		BIT(2)
-#define  ECC_CONTROL_TX_RAM_INJ_ERROR_3		BIT(3)
-#define  ECC_CONTROL_RX_RAM_INJ_ERROR_0		BIT(4)
-#define  ECC_CONTROL_RX_RAM_INJ_ERROR_1		BIT(5)
-#define  ECC_CONTROL_RX_RAM_INJ_ERROR_2		BIT(6)
-#define  ECC_CONTROL_RX_RAM_INJ_ERROR_3		BIT(7)
-#define  ECC_CONTROL_PCIE2AXI_RAM_INJ_ERROR_0	BIT(8)
-#define  ECC_CONTROL_PCIE2AXI_RAM_INJ_ERROR_1	BIT(9)
-#define  ECC_CONTROL_PCIE2AXI_RAM_INJ_ERROR_2	BIT(10)
-#define  ECC_CONTROL_PCIE2AXI_RAM_INJ_ERROR_3	BIT(11)
-#define  ECC_CONTROL_AXI2PCIE_RAM_INJ_ERROR_0	BIT(12)
-#define  ECC_CONTROL_AXI2PCIE_RAM_INJ_ERROR_1	BIT(13)
-#define  ECC_CONTROL_AXI2PCIE_RAM_INJ_ERROR_2	BIT(14)
-#define  ECC_CONTROL_AXI2PCIE_RAM_INJ_ERROR_3	BIT(15)
-#define  ECC_CONTROL_TX_RAM_ECC_BYPASS		BIT(24)
-#define  ECC_CONTROL_RX_RAM_ECC_BYPASS		BIT(25)
-#define  ECC_CONTROL_PCIE2AXI_RAM_ECC_BYPASS	BIT(26)
-#define  ECC_CONTROL_AXI2PCIE_RAM_ECC_BYPASS	BIT(27)
-#define LTSSM_STATE				0x5c
-#define  LTSSM_L0_STATE				0x10
-#define PCIE_EVENT_INT				0x14c
-#define  PCIE_EVENT_INT_L2_EXIT_INT		BIT(0)
-#define  PCIE_EVENT_INT_HOTRST_EXIT_INT		BIT(1)
-#define  PCIE_EVENT_INT_DLUP_EXIT_INT		BIT(2)
-#define  PCIE_EVENT_INT_MASK			GENMASK(2, 0)
-#define  PCIE_EVENT_INT_L2_EXIT_INT_MASK	BIT(16)
-#define  PCIE_EVENT_INT_HOTRST_EXIT_INT_MASK	BIT(17)
-#define  PCIE_EVENT_INT_DLUP_EXIT_INT_MASK	BIT(18)
-#define  PCIE_EVENT_INT_ENB_MASK		GENMASK(18, 16)
-#define  PCIE_EVENT_INT_ENB_SHIFT		16
-#define  NUM_PCIE_EVENTS			(3)
-
 /* PCIe Bridge Phy Regs */
-#define PCIE_PCI_IDS_DW1			0x9c
-
-/* PCIe Config space MSI capability structure */
-#define MC_MSI_CAP_CTRL_OFFSET			0xe0u
-#define  MC_MSI_MAX_Q_AVAIL			(MC_NUM_MSI_IRQS_CODED << 1)
-#define  MC_MSI_Q_SIZE				(MC_NUM_MSI_IRQS_CODED << 4)
-
 #define IMASK_LOCAL				0x180
 #define  DMA_END_ENGINE_0_MASK			0x00000000u
 #define  DMA_END_ENGINE_0_SHIFT			0
@@ -137,7 +78,8 @@
 #define ISTATUS_LOCAL				0x184
 #define IMASK_HOST				0x188
 #define ISTATUS_HOST				0x18c
-#define MSI_ADDR				0x190
+#define IMSI_ADDR				0x190
+#define  MSI_ADDR				0x190
 #define ISTATUS_MSI				0x194
 
 /* PCIe Master table init defines */
@@ -162,6 +104,62 @@
 
 #define ATR_ENTRY_SIZE				32
 
+/* PCIe Controller Phy Regs */
+#define SEC_ERROR_EVENT_CNT			0x20
+#define DED_ERROR_EVENT_CNT			0x24
+#define SEC_ERROR_INT				0x28
+#define  SEC_ERROR_INT_TX_RAM_SEC_ERR_INT	GENMASK(3, 0)
+#define  SEC_ERROR_INT_RX_RAM_SEC_ERR_INT	GENMASK(7, 4)
+#define  SEC_ERROR_INT_PCIE2AXI_RAM_SEC_ERR_INT	GENMASK(11, 8)
+#define  SEC_ERROR_INT_AXI2PCIE_RAM_SEC_ERR_INT	GENMASK(15, 12)
+#define  NUM_SEC_ERROR_INTS			(4)
+#define SEC_ERROR_INT_MASK			0x2c
+#define DED_ERROR_INT				0x30
+#define  DED_ERROR_INT_TX_RAM_DED_ERR_INT	GENMASK(3, 0)
+#define  DED_ERROR_INT_RX_RAM_DED_ERR_INT	GENMASK(7, 4)
+#define  DED_ERROR_INT_PCIE2AXI_RAM_DED_ERR_INT	GENMASK(11, 8)
+#define  DED_ERROR_INT_AXI2PCIE_RAM_DED_ERR_INT	GENMASK(15, 12)
+#define  NUM_DED_ERROR_INTS			(4)
+#define DED_ERROR_INT_MASK			0x34
+#define ECC_CONTROL				0x38
+#define  ECC_CONTROL_TX_RAM_INJ_ERROR_0		BIT(0)
+#define  ECC_CONTROL_TX_RAM_INJ_ERROR_1		BIT(1)
+#define  ECC_CONTROL_TX_RAM_INJ_ERROR_2		BIT(2)
+#define  ECC_CONTROL_TX_RAM_INJ_ERROR_3		BIT(3)
+#define  ECC_CONTROL_RX_RAM_INJ_ERROR_0		BIT(4)
+#define  ECC_CONTROL_RX_RAM_INJ_ERROR_1		BIT(5)
+#define  ECC_CONTROL_RX_RAM_INJ_ERROR_2		BIT(6)
+#define  ECC_CONTROL_RX_RAM_INJ_ERROR_3		BIT(7)
+#define  ECC_CONTROL_PCIE2AXI_RAM_INJ_ERROR_0	BIT(8)
+#define  ECC_CONTROL_PCIE2AXI_RAM_INJ_ERROR_1	BIT(9)
+#define  ECC_CONTROL_PCIE2AXI_RAM_INJ_ERROR_2	BIT(10)
+#define  ECC_CONTROL_PCIE2AXI_RAM_INJ_ERROR_3	BIT(11)
+#define  ECC_CONTROL_AXI2PCIE_RAM_INJ_ERROR_0	BIT(12)
+#define  ECC_CONTROL_AXI2PCIE_RAM_INJ_ERROR_1	BIT(13)
+#define  ECC_CONTROL_AXI2PCIE_RAM_INJ_ERROR_2	BIT(14)
+#define  ECC_CONTROL_AXI2PCIE_RAM_INJ_ERROR_3	BIT(15)
+#define  ECC_CONTROL_TX_RAM_ECC_BYPASS		BIT(24)
+#define  ECC_CONTROL_RX_RAM_ECC_BYPASS		BIT(25)
+#define  ECC_CONTROL_PCIE2AXI_RAM_ECC_BYPASS	BIT(26)
+#define  ECC_CONTROL_AXI2PCIE_RAM_ECC_BYPASS	BIT(27)
+#define PCIE_EVENT_INT				0x14c
+#define  PCIE_EVENT_INT_L2_EXIT_INT		BIT(0)
+#define  PCIE_EVENT_INT_HOTRST_EXIT_INT		BIT(1)
+#define  PCIE_EVENT_INT_DLUP_EXIT_INT		BIT(2)
+#define  PCIE_EVENT_INT_MASK			GENMASK(2, 0)
+#define  PCIE_EVENT_INT_L2_EXIT_INT_MASK	BIT(16)
+#define  PCIE_EVENT_INT_HOTRST_EXIT_INT_MASK	BIT(17)
+#define  PCIE_EVENT_INT_DLUP_EXIT_INT_MASK	BIT(18)
+#define  PCIE_EVENT_INT_ENB_MASK		GENMASK(18, 16)
+#define  PCIE_EVENT_INT_ENB_SHIFT		16
+#define  NUM_PCIE_EVENTS			(3)
+
+/* PCIe Config space MSI capability structure */
+#define MC_MSI_CAP_CTRL_OFFSET			0xe0u
+#define  MC_MSI_MAX_Q_AVAIL			(MC_NUM_MSI_IRQS_CODED << 1)
+#define  MC_MSI_Q_SIZE				(MC_NUM_MSI_IRQS_CODED << 4)
+
+/* Events */
 #define EVENT_PCIE_L2_EXIT			0
 #define EVENT_PCIE_HOTRST_EXIT			1
 #define EVENT_PCIE_DLUP_EXIT			2
@@ -1086,7 +1084,7 @@ static int mc_platform_init(struct pci_config_window *cfg)
 	      SEC_ERROR_INT_AXI2PCIE_RAM_SEC_ERR_INT;
 	writel_relaxed(val, ctrl_base_addr + SEC_ERROR_INT);
 	writel_relaxed(0, ctrl_base_addr + SEC_ERROR_INT_MASK);
-	writel_relaxed(0, ctrl_base_addr + SEC_ERROR_CNT);
+	writel_relaxed(0, ctrl_base_addr + SEC_ERROR_EVENT_CNT);
 
 	val = DED_ERROR_INT_TX_RAM_DED_ERR_INT |
 	      DED_ERROR_INT_RX_RAM_DED_ERR_INT |
@@ -1094,7 +1092,7 @@ static int mc_platform_init(struct pci_config_window *cfg)
 	      DED_ERROR_INT_AXI2PCIE_RAM_DED_ERR_INT;
 	writel_relaxed(val, ctrl_base_addr + DED_ERROR_INT);
 	writel_relaxed(0, ctrl_base_addr + DED_ERROR_INT_MASK);
-	writel_relaxed(0, ctrl_base_addr + DED_ERROR_CNT);
+	writel_relaxed(0, ctrl_base_addr + DED_ERROR_EVENT_CNT);
 
 	writel_relaxed(0, bridge_base_addr + IMASK_HOST);
 	writel_relaxed(GENMASK(31, 0), bridge_base_addr + ISTATUS_HOST);
Signature · 1 line
2.25.1
#4 lore raw

PATCH v3 4/7 PCI: microchip: Enable event handlers to access bridge and ctrl ptrs

In reply to [email protected]

From: Daire McNamara <[email protected]>

Minor re-organisation so that event handlers can access both a pointer to the bridge area of the PCIe Root Port and the ctrl area of the PCIe Root Port.

---
 drivers/pci/controller/pcie-microchip-host.c | 31 ++++++++++----------
 1 file changed, 16 insertions(+), 15 deletions(-)
drivers/pci/controller/pcie-microchip-host.c +16 -15
index 30153fd1a2b3..a81e6d25e347 100644
@@ -654,9 +654,10 @@ static inline u32 reg_to_event(u32 reg, struct event_map field)
 	return (reg & field.reg_mask) ? BIT(field.event_bit) : 0;
 }
 
-static u32 pcie_events(void __iomem *addr)
+static u32 pcie_events(struct mc_pcie *port)
 {
-	u32 reg = readl_relaxed(addr);
+	void __iomem *ctrl_base_addr = port->axi_base_addr + MC_PCIE_CTRL_ADDR;
+	u32 reg = readl_relaxed(ctrl_base_addr + PCIE_EVENT_INT);
 	u32 val = 0;
 	int i;
 
@@ -666,9 +667,10 @@ static u32 pcie_events(void __iomem *addr)
 	return val;
 }
 
-static u32 sec_errors(void __iomem *addr)
+static u32 sec_errors(struct mc_pcie *port)
 {
-	u32 reg = readl_relaxed(addr);
+	void __iomem *ctrl_base_addr = port->axi_base_addr + MC_PCIE_CTRL_ADDR;
+	u32 reg = readl_relaxed(ctrl_base_addr + SEC_ERROR_INT);
 	u32 val = 0;
 	int i;
 
@@ -678,9 +680,10 @@ static u32 sec_errors(void __iomem *addr)
 	return val;
 }
 
-static u32 ded_errors(void __iomem *addr)
+static u32 ded_errors(struct mc_pcie *port)
 {
-	u32 reg = readl_relaxed(addr);
+	void __iomem *ctrl_base_addr = port->axi_base_addr + MC_PCIE_CTRL_ADDR;
+	u32 reg = readl_relaxed(ctrl_base_addr + DED_ERROR_INT);
 	u32 val = 0;
 	int i;
 
@@ -690,9 +693,10 @@ static u32 ded_errors(void __iomem *addr)
 	return val;
 }
 
-static u32 local_events(void __iomem *addr)
+static u32 local_events(struct mc_pcie *port)
 {
-	u32 reg = readl_relaxed(addr);
+	void __iomem *bridge_base_addr = port->axi_base_addr + MC_PCIE_BRIDGE_ADDR;
+	u32 reg = readl_relaxed(bridge_base_addr + ISTATUS_LOCAL);
 	u32 val = 0;
 	int i;
 
@@ -704,15 +708,12 @@ static u32 local_events(void __iomem *addr)
 
 static u32 get_events(struct mc_pcie *port)
 {
-	void __iomem *bridge_base_addr =
-		port->axi_base_addr + MC_PCIE_BRIDGE_ADDR;
-	void __iomem *ctrl_base_addr = port->axi_base_addr + MC_PCIE_CTRL_ADDR;
 	u32 events = 0;
 
-	events |= pcie_events(ctrl_base_addr + PCIE_EVENT_INT);
-	events |= sec_errors(ctrl_base_addr + SEC_ERROR_INT);
-	events |= ded_errors(ctrl_base_addr + DED_ERROR_INT);
-	events |= local_events(bridge_base_addr + ISTATUS_LOCAL);
+	events |= pcie_events(port);
+	events |= sec_errors(port);
+	events |= ded_errors(port);
+	events |= local_events(port);
 
 	return events;
 }
Signature · 1 line
2.25.1
#5 lore raw

PATCH v3 5/7 PCI: microchip: Clean up initialisation of interrupts

In reply to [email protected]

From: Daire McNamara <[email protected]>

Refactor interrupt handling in _init() function into disable_interrupts(), init_interrupts(), clear_sec_errors() and clear ded_errors(). It was unwieldy and prone to bugs. Then clearly disable interrupts as soon as possible and only enable interrupts after address translation is setup to prevent spurious axi2pcie and pcie2axi translation errors being reported

---
 drivers/pci/controller/pcie-microchip-host.c | 156 ++++++++++++-------
 1 file changed, 100 insertions(+), 56 deletions(-)
drivers/pci/controller/pcie-microchip-host.c +100 -56
index a81e6d25e347..7b212eea42d2 100644
@@ -112,6 +112,7 @@
 #define  SEC_ERROR_INT_RX_RAM_SEC_ERR_INT	GENMASK(7, 4)
 #define  SEC_ERROR_INT_PCIE2AXI_RAM_SEC_ERR_INT	GENMASK(11, 8)
 #define  SEC_ERROR_INT_AXI2PCIE_RAM_SEC_ERR_INT	GENMASK(15, 12)
+#define  SEC_ERROR_INT_ALL_RAM_SEC_ERR_INT	GENMASK(15, 0)
 #define  NUM_SEC_ERROR_INTS			(4)
 #define SEC_ERROR_INT_MASK			0x2c
 #define DED_ERROR_INT				0x30
@@ -119,6 +120,7 @@
 #define  DED_ERROR_INT_RX_RAM_DED_ERR_INT	GENMASK(7, 4)
 #define  DED_ERROR_INT_PCIE2AXI_RAM_DED_ERR_INT	GENMASK(11, 8)
 #define  DED_ERROR_INT_AXI2PCIE_RAM_DED_ERR_INT	GENMASK(15, 12)
+#define  DED_ERROR_INT_ALL_RAM_DED_ERR_INT	GENMASK(15, 0)
 #define  NUM_DED_ERROR_INTS			(4)
 #define DED_ERROR_INT_MASK			0x34
 #define ECC_CONTROL				0x38
@@ -986,39 +988,73 @@ static int mc_pcie_setup_windows(struct platform_device *pdev,
 	return 0;
 }
 
-static int mc_platform_init(struct pci_config_window *cfg)
+static inline void mc_clear_secs(struct mc_pcie *port)
 {
-	struct device *dev = cfg->parent;
-	struct platform_device *pdev = to_platform_device(dev);
-	struct mc_pcie *port;
-	void __iomem *bridge_base_addr;
-	void __iomem *ctrl_base_addr;
-	int ret;
-	int irq;
-	int i, intx_irq, msi_irq, event_irq;
+	void __iomem *ctrl_base_addr = port->axi_base_addr + MC_PCIE_CTRL_ADDR;
+
+	writel_relaxed(SEC_ERROR_INT_ALL_RAM_SEC_ERR_INT, ctrl_base_addr +
+		       SEC_ERROR_INT);
+	writel_relaxed(0, ctrl_base_addr + SEC_ERROR_EVENT_CNT);
+}
+
+static inline void mc_clear_deds(struct mc_pcie *port)
+{
+	void __iomem *ctrl_base_addr = port->axi_base_addr + MC_PCIE_CTRL_ADDR;
+
+	writel_relaxed(DED_ERROR_INT_ALL_RAM_DED_ERR_INT, ctrl_base_addr +
+		       DED_ERROR_INT);
+	writel_relaxed(0, ctrl_base_addr + DED_ERROR_EVENT_CNT);
+}
+
+static void mc_disable_interrupts(struct mc_pcie *port)
+{
+	void __iomem *bridge_base_addr = port->axi_base_addr + MC_PCIE_BRIDGE_ADDR;
+	void __iomem *ctrl_base_addr = port->axi_base_addr + MC_PCIE_CTRL_ADDR;
 	u32 val;
-	int err;
 
-	port = devm_kzalloc(dev, sizeof(*port), GFP_KERNEL);
-	if (!port)
-		return -ENOMEM;
-	port->dev = dev;
+	/* Ensure ECC bypass is enabled */
+	val = ECC_CONTROL_TX_RAM_ECC_BYPASS |
+	      ECC_CONTROL_RX_RAM_ECC_BYPASS |
+	      ECC_CONTROL_PCIE2AXI_RAM_ECC_BYPASS |
+	      ECC_CONTROL_AXI2PCIE_RAM_ECC_BYPASS;
+	writel_relaxed(val, ctrl_base_addr + ECC_CONTROL);
 
-	ret = mc_pcie_init_clks(dev);
-	if (ret) {
-		dev_err(dev, "failed to get clock resources, error %d\n", ret);
-		return -ENODEV;
-	}
+	/* Disable SEC errors and clear any outstanding */
+	writel_relaxed(SEC_ERROR_INT_ALL_RAM_SEC_ERR_INT, ctrl_base_addr +
+		       SEC_ERROR_INT_MASK);
+	mc_clear_secs(port);
 
-	port->axi_base_addr = devm_platform_ioremap_resource(pdev, 1);
-	if (IS_ERR(port->axi_base_addr))
-		return PTR_ERR(port->axi_base_addr);
+	/* Disable DED errors and clear any outstanding */
+	writel_relaxed(DED_ERROR_INT_ALL_RAM_DED_ERR_INT, ctrl_base_addr +
+		       DED_ERROR_INT_MASK);
+	mc_clear_deds(port);
 
-	bridge_base_addr = port->axi_base_addr + MC_PCIE_BRIDGE_ADDR;
-	ctrl_base_addr = port->axi_base_addr + MC_PCIE_CTRL_ADDR;
+	/* Disable local interrupts and clear any outstanding */
+	writel_relaxed(0, bridge_base_addr + IMASK_LOCAL);
+	writel_relaxed(GENMASK(31, 0), bridge_base_addr + ISTATUS_LOCAL);
+	writel_relaxed(GENMASK(31, 0), bridge_base_addr + ISTATUS_MSI);
+
+	/* Disable PCIe events and clear any outstanding */
+	val = PCIE_EVENT_INT_L2_EXIT_INT |
+	      PCIE_EVENT_INT_HOTRST_EXIT_INT |
+	      PCIE_EVENT_INT_DLUP_EXIT_INT |
+	      PCIE_EVENT_INT_L2_EXIT_INT_MASK |
+	      PCIE_EVENT_INT_HOTRST_EXIT_INT_MASK |
+	      PCIE_EVENT_INT_DLUP_EXIT_INT_MASK;
+	writel_relaxed(val, ctrl_base_addr + PCIE_EVENT_INT);
+
+	/* Disable host interrupts and clear any outstanding */
+	writel_relaxed(0, bridge_base_addr + IMASK_HOST);
+	writel_relaxed(GENMASK(31, 0), bridge_base_addr + ISTATUS_HOST);
+}
+
+static int mc_init_interrupts(struct platform_device *pdev, struct mc_pcie *port)
+{
+	struct device *dev = &pdev->dev;
+	int irq;
+	int i, intx_irq, msi_irq, event_irq;
+	int ret;
 
-	port->msi.vector_phy = MSI_ADDR;
-	port->msi.num_vectors = MC_NUM_MSI_IRQS;
 	ret = mc_pcie_init_irq_domains(port);
 	if (ret) {
 		dev_err(dev, "failed creating IRQ domains\n");
@@ -1036,11 +1072,11 @@ static int mc_platform_init(struct pci_config_window *cfg)
 			return -ENXIO;
 		}
 
-		err = devm_request_irq(dev, event_irq, mc_event_handler,
+		ret = devm_request_irq(dev, event_irq, mc_event_handler,
 				       0, event_cause[i].sym, port);
-		if (err) {
+		if (ret) {
 			dev_err(dev, "failed to request IRQ %d\n", event_irq);
-			return err;
+			return ret;
 		}
 	}
 
@@ -1065,44 +1101,52 @@ static int mc_platform_init(struct pci_config_window *cfg)
 	/* Plug the main event chained handler */
 	irq_set_chained_handler_and_data(irq, mc_handle_event, port);
 
-	/* Hardware doesn't setup MSI by default */
-	mc_pcie_enable_msi(port, cfg->win);
+	return 0;
+}
 
-	val = readl_relaxed(bridge_base_addr + IMASK_LOCAL);
-	val |= PM_MSI_INT_INTX_MASK;
-	writel_relaxed(val, bridge_base_addr + IMASK_LOCAL);
+static int mc_platform_init(struct pci_config_window *cfg)
+{
+	struct device *dev = cfg->parent;
+	struct platform_device *pdev = to_platform_device(dev);
+	struct mc_pcie *port;
+	void __iomem *bridge_base_addr;
+	int ret;
 
-	writel_relaxed(val, ctrl_base_addr + ECC_CONTROL);
+	port = devm_kzalloc(dev, sizeof(*port), GFP_KERNEL);
+	if (!port)
+		return -ENOMEM;
+	port->dev = dev;
 
-	val = PCIE_EVENT_INT_L2_EXIT_INT |
-	      PCIE_EVENT_INT_HOTRST_EXIT_INT |
-	      PCIE_EVENT_INT_DLUP_EXIT_INT;
-	writel_relaxed(val, ctrl_base_addr + PCIE_EVENT_INT);
+	ret = mc_pcie_init_clks(dev);
+	if (ret) {
+		dev_err(dev, "failed to get clock resources, error %d\n", ret);
+		return -ENODEV;
+	}
 
-	val = SEC_ERROR_INT_TX_RAM_SEC_ERR_INT |
-	      SEC_ERROR_INT_RX_RAM_SEC_ERR_INT |
-	      SEC_ERROR_INT_PCIE2AXI_RAM_SEC_ERR_INT |
-	      SEC_ERROR_INT_AXI2PCIE_RAM_SEC_ERR_INT;
-	writel_relaxed(val, ctrl_base_addr + SEC_ERROR_INT);
-	writel_relaxed(0, ctrl_base_addr + SEC_ERROR_INT_MASK);
-	writel_relaxed(0, ctrl_base_addr + SEC_ERROR_EVENT_CNT);
+	port->axi_base_addr = devm_platform_ioremap_resource(pdev, 1);
+	if (IS_ERR(port->axi_base_addr))
+		return PTR_ERR(port->axi_base_addr);
 
-	val = DED_ERROR_INT_TX_RAM_DED_ERR_INT |
-	      DED_ERROR_INT_RX_RAM_DED_ERR_INT |
-	      DED_ERROR_INT_PCIE2AXI_RAM_DED_ERR_INT |
-	      DED_ERROR_INT_AXI2PCIE_RAM_DED_ERR_INT;
-	writel_relaxed(val, ctrl_base_addr + DED_ERROR_INT);
-	writel_relaxed(0, ctrl_base_addr + DED_ERROR_INT_MASK);
-	writel_relaxed(0, ctrl_base_addr + DED_ERROR_EVENT_CNT);
+	mc_disable_interrupts(port);
 
-	writel_relaxed(0, bridge_base_addr + IMASK_HOST);
-	writel_relaxed(GENMASK(31, 0), bridge_base_addr + ISTATUS_HOST);
+	bridge_base_addr = port->axi_base_addr + MC_PCIE_BRIDGE_ADDR;
+
+	port->msi.vector_phy = MSI_ADDR;
+	port->msi.num_vectors = MC_NUM_MSI_IRQS;
+
+	/* Hardware doesn't setup MSI by default */
+	mc_pcie_enable_msi(port, cfg->win);
 
 	/* Configure Address Translation Table 0 for PCIe config space */
 	mc_pcie_setup_window(bridge_base_addr, 0, cfg->res.start & 0xffffffff,
 			     cfg->res.start, resource_size(&cfg->res));
 
-	return mc_pcie_setup_windows(pdev, port);
+	ret = mc_pcie_setup_windows(pdev, port);
+	if (ret)
+		return ret;
+
+	/* Address translation is up; safe to enable interrupts */
+	return mc_init_interrupts(pdev, port);
 }
 
 static const struct pci_ecam_ops mc_ecam_ops = {
Signature · 1 line
2.25.1
#6 lore raw

PATCH v3 6/7 PCI: microchip: Gather MSI information from hardware config registers

In reply to [email protected]

From: Daire McNamara <[email protected]>

The PCIe Root Complex on PolarFire SoC is configured at bitstream creation time using Libero. Key MSI-related parameters include the number of MSIs (1/2/4/8/16/32) and the MSI address. In the device driver, extract this information from hw registers at init time, and use it to configure MSI system, including configuring MSI capability structure correctly in configuration space.

---
 drivers/pci/controller/pcie-microchip-host.c | 65 +++++++++++---------
 1 file changed, 37 insertions(+), 28 deletions(-)
drivers/pci/controller/pcie-microchip-host.c +37 -28
index 7b212eea42d2..ca13fd56a0d9 100644
@@ -7,6 +7,7 @@
  * Author: Daire McNamara <[email protected]>
  */
 
+#include <linux/bitfield.h>
 #include <linux/clk.h>
 #include <linux/irqchip/chained_irq.h>
 #include <linux/irqdomain.h>
@@ -20,8 +21,7 @@
 #include "../pci.h"
 
 /* Number of MSI IRQs */
-#define MC_NUM_MSI_IRQS				32
-#define MC_NUM_MSI_IRQS_CODED			5
+#define MC_MAX_NUM_MSI_IRQS			32
 
 /* PCIe Bridge Phy and Controller Phy offsets */
 #define MC_PCIE1_BRIDGE_ADDR			0x00008000u
@@ -31,6 +31,11 @@
 #define MC_PCIE_CTRL_ADDR			(MC_PCIE1_CTRL_ADDR)
 
 /* PCIe Bridge Phy Regs */
+#define PCIE_PCI_IRQ_DW0			0xa8
+#define  MSIX_CAP_MASK				BIT(31)
+#define  NUM_MSI_MSGS_MASK			GENMASK(6, 4)
+#define  NUM_MSI_MSGS_SHIFT			4
+
 #define IMASK_LOCAL				0x180
 #define  DMA_END_ENGINE_0_MASK			0x00000000u
 #define  DMA_END_ENGINE_0_SHIFT			0
@@ -79,7 +84,6 @@
 #define IMASK_HOST				0x188
 #define ISTATUS_HOST				0x18c
 #define IMSI_ADDR				0x190
-#define  MSI_ADDR				0x190
 #define ISTATUS_MSI				0x194
 
 /* PCIe Master table init defines */
@@ -158,8 +162,6 @@
 
 /* PCIe Config space MSI capability structure */
 #define MC_MSI_CAP_CTRL_OFFSET			0xe0u
-#define  MC_MSI_MAX_Q_AVAIL			(MC_NUM_MSI_IRQS_CODED << 1)
-#define  MC_MSI_Q_SIZE				(MC_NUM_MSI_IRQS_CODED << 4)
 
 /* Events */
 #define EVENT_PCIE_L2_EXIT			0
@@ -259,7 +261,7 @@ struct mc_msi {
 	struct irq_domain *dev_domain;
 	u32 num_vectors;
 	u64 vector_phy;
-	DECLARE_BITMAP(used, MC_NUM_MSI_IRQS);
+	DECLARE_BITMAP(used, MC_MAX_NUM_MSI_IRQS);
 };
 
 struct mc_pcie {
@@ -382,25 +384,27 @@ static struct {
 
 static char poss_clks[][5] = { "fic0", "fic1", "fic2", "fic3" };
 
-static void mc_pcie_enable_msi(struct mc_pcie *port, void __iomem *base)
+static void mc_pcie_enable_msi(struct mc_pcie *port, void __iomem *ecam)
 {
 	struct mc_msi *msi = &port->msi;
-	u32 cap_offset = MC_MSI_CAP_CTRL_OFFSET;
-	u16 msg_ctrl = readw_relaxed(base + cap_offset + PCI_MSI_FLAGS);
+	u16 reg;
+	u8 queue_size;
 
-	msg_ctrl |= PCI_MSI_FLAGS_ENABLE;
-	msg_ctrl &= ~PCI_MSI_FLAGS_QMASK;
-	msg_ctrl |= MC_MSI_MAX_Q_AVAIL;
-	msg_ctrl &= ~PCI_MSI_FLAGS_QSIZE;
-	msg_ctrl |= MC_MSI_Q_SIZE;
-	msg_ctrl |= PCI_MSI_FLAGS_64BIT;
+	/* Fixup MSI enable flag */
+	reg = readw_relaxed(ecam + MC_MSI_CAP_CTRL_OFFSET + PCI_MSI_FLAGS);
+	reg |= PCI_MSI_FLAGS_ENABLE;
+	writew_relaxed(reg, ecam + MC_MSI_CAP_CTRL_OFFSET + PCI_MSI_FLAGS);
 
-	writew_relaxed(msg_ctrl, base + cap_offset + PCI_MSI_FLAGS);
+	/* Fixup PCI MSI queue flags */
+	queue_size = FIELD_GET(PCI_MSI_FLAGS_QMASK, reg);
+	reg |= FIELD_PREP(PCI_MSI_FLAGS_QSIZE, queue_size);
+	writew_relaxed(reg, ecam + MC_MSI_CAP_CTRL_OFFSET + PCI_MSI_FLAGS);
 
+	/* Fixup MSI addr fields */
 	writel_relaxed(lower_32_bits(msi->vector_phy),
-		       base + cap_offset + PCI_MSI_ADDRESS_LO);
+		       ecam + MC_MSI_CAP_CTRL_OFFSET + PCI_MSI_ADDRESS_LO);
 	writel_relaxed(upper_32_bits(msi->vector_phy),
-		       base + cap_offset + PCI_MSI_ADDRESS_HI);
+		       ecam + MC_MSI_CAP_CTRL_OFFSET + PCI_MSI_ADDRESS_HI);
 }
 
 static void mc_handle_msi(struct irq_desc *desc)
@@ -473,10 +477,7 @@ static int mc_irq_msi_domain_alloc(struct irq_domain *domain, unsigned int virq,
 {
 	struct mc_pcie *port = domain->host_data;
 	struct mc_msi *msi = &port->msi;
-	void __iomem *bridge_base_addr =
-		port->axi_base_addr + MC_PCIE_BRIDGE_ADDR;
 	unsigned long bit;
-	u32 val;
 
 	mutex_lock(&msi->lock);
 	bit = find_first_zero_bit(msi->used, msi->num_vectors);
@@ -490,11 +491,6 @@ static int mc_irq_msi_domain_alloc(struct irq_domain *domain, unsigned int virq,
 	irq_domain_set_info(domain, virq, bit, &mc_msi_bottom_irq_chip,
 			    domain->host_data, handle_edge_irq, NULL, NULL);
 
-	/* Enable MSI interrupts */
-	val = readl_relaxed(bridge_base_addr + IMASK_LOCAL);
-	val |= PM_MSI_INT_MSI_MASK;
-	writel_relaxed(val, bridge_base_addr + IMASK_LOCAL);
-
 	mutex_unlock(&msi->lock);
 
 	return 0;
@@ -1111,6 +1107,7 @@ static int mc_platform_init(struct pci_config_window *cfg)
 	struct mc_pcie *port;
 	void __iomem *bridge_base_addr;
 	int ret;
+	u32 val;
 
 	port = devm_kzalloc(dev, sizeof(*port), GFP_KERNEL);
 	if (!port)
@@ -1131,12 +1128,24 @@ static int mc_platform_init(struct pci_config_window *cfg)
 
 	bridge_base_addr = port->axi_base_addr + MC_PCIE_BRIDGE_ADDR;
 
-	port->msi.vector_phy = MSI_ADDR;
-	port->msi.num_vectors = MC_NUM_MSI_IRQS;
+	/* Allow enabling MSI by disabling MSI-X */
+	val = readl(bridge_base_addr + PCIE_PCI_IRQ_DW0);
+	val &= ~MSIX_CAP_MASK;
+	writel(val, bridge_base_addr + PCIE_PCI_IRQ_DW0);
 
 	/* Hardware doesn't setup MSI by default */
 	mc_pcie_enable_msi(port, cfg->win);
 
+	/* Pick num vectors from bitfile programmed onto FPGA fabric */
+	val = readl(bridge_base_addr + PCIE_PCI_IRQ_DW0);
+	val &= NUM_MSI_MSGS_MASK;
+	val >>= NUM_MSI_MSGS_SHIFT;
+
+	port->msi.num_vectors = 1 << val;
+
+	/* Pick vector address from design */
+	port->msi.vector_phy = readl_relaxed(bridge_base_addr + IMSI_ADDR);
+
 	/* Configure Address Translation Table 0 for PCIe config space */
 	mc_pcie_setup_window(bridge_base_addr, 0, cfg->res.start & 0xffffffff,
 			     cfg->res.start, resource_size(&cfg->res));
Signature · 1 line
2.25.1
#7 lore raw

PATCH v3 7/7 PCI: microchip: Re-partition code between probe() and init()

In reply to [email protected]

From: Daire McNamara <[email protected]>

Continuing to use pci_host_common_probe() for the PCIe Root Complex on PolarFire SoC was leading to an extremely large _init() function and some unnatural code flow. Re-partition so some tasks are done in a _probe() routine, which calls pci_host_common_probe() and then use a much smaller _init() function, mainly to enable interrupts after address translation tables are set up.

---
 drivers/pci/controller/pcie-microchip-host.c | 58 +++++++++++++-------
 1 file changed, 38 insertions(+), 20 deletions(-)
drivers/pci/controller/pcie-microchip-host.c +38 -20
index ca13fd56a0d9..252aff180ca2 100644
@@ -384,6 +384,8 @@ static struct {
 
 static char poss_clks[][5] = { "fic0", "fic1", "fic2", "fic3" };
 
+static struct mc_pcie *port;
+
 static void mc_pcie_enable_msi(struct mc_pcie *port, void __iomem *ecam)
 {
 	struct mc_msi *msi = &port->msi;
@@ -1104,7 +1106,34 @@ static int mc_platform_init(struct pci_config_window *cfg)
 {
 	struct device *dev = cfg->parent;
 	struct platform_device *pdev = to_platform_device(dev);
-	struct mc_pcie *port;
+	void __iomem *bridge_base_addr =
+		port->axi_base_addr + MC_PCIE_BRIDGE_ADDR;
+	int ret;
+
+	/* Configure address translation table 0 for PCIe config space */
+	mc_pcie_setup_window(bridge_base_addr, 0, cfg->res.start,
+			     cfg->res.start,
+			     resource_size(&cfg->res));
+
+	/* Need some fixups in config space */
+	mc_pcie_enable_msi(port, cfg->win);
+
+	/* Configure non-config space outbound ranges */
+	ret = mc_pcie_setup_windows(pdev, port);
+	if (ret)
+		return ret;
+
+	/* Address translation is up; safe to enable interrupts */
+	ret = mc_init_interrupts(pdev, port);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static int mc_host_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
 	void __iomem *bridge_base_addr;
 	int ret;
 	u32 val;
@@ -1112,13 +1141,8 @@ static int mc_platform_init(struct pci_config_window *cfg)
 	port = devm_kzalloc(dev, sizeof(*port), GFP_KERNEL);
 	if (!port)
 		return -ENOMEM;
-	port->dev = dev;
 
-	ret = mc_pcie_init_clks(dev);
-	if (ret) {
-		dev_err(dev, "failed to get clock resources, error %d\n", ret);
-		return -ENODEV;
-	}
+	port->dev = dev;
 
 	port->axi_base_addr = devm_platform_ioremap_resource(pdev, 1);
 	if (IS_ERR(port->axi_base_addr))
@@ -1133,9 +1157,6 @@ static int mc_platform_init(struct pci_config_window *cfg)
 	val &= ~MSIX_CAP_MASK;
 	writel(val, bridge_base_addr + PCIE_PCI_IRQ_DW0);
 
-	/* Hardware doesn't setup MSI by default */
-	mc_pcie_enable_msi(port, cfg->win);
-
 	/* Pick num vectors from bitfile programmed onto FPGA fabric */
 	val = readl(bridge_base_addr + PCIE_PCI_IRQ_DW0);
 	val &= NUM_MSI_MSGS_MASK;
@@ -1146,16 +1167,13 @@ static int mc_platform_init(struct pci_config_window *cfg)
 	/* Pick vector address from design */
 	port->msi.vector_phy = readl_relaxed(bridge_base_addr + IMSI_ADDR);
 
-	/* Configure Address Translation Table 0 for PCIe config space */
-	mc_pcie_setup_window(bridge_base_addr, 0, cfg->res.start & 0xffffffff,
-			     cfg->res.start, resource_size(&cfg->res));
-
-	ret = mc_pcie_setup_windows(pdev, port);
-	if (ret)
-		return ret;
+	ret = mc_pcie_init_clks(dev);
+	if (ret) {
+		dev_err(dev, "failed to get clock resources, error %d\n", ret);
+		return -ENODEV;
+	}
 
-	/* Address translation is up; safe to enable interrupts */
-	return mc_init_interrupts(pdev, port);
+	return pci_host_common_probe(pdev);
 }
 
 static const struct pci_ecam_ops mc_ecam_ops = {
@@ -1178,7 +1196,7 @@ static const struct of_device_id mc_pcie_of_match[] = {
 MODULE_DEVICE_TABLE(of, mc_pcie_of_match);
 
 static struct platform_driver mc_pcie_driver = {
-	.probe = pci_host_common_probe,
+	.probe = mc_host_probe,
 	.driver = {
 		.name = "microchip-pcie",
 		.of_match_table = mc_pcie_of_match,
Signature · 1 line
2.25.1
#8 lore raw

Re: [PATCH v3 7/7] PCI: microchip: Re-partition code between probe() and init()

Quoted 25 lines · On Fri, Jul 28, 2023 at 02:14:01PM +0100, [email protected] wrote:

From: Daire McNamara <[email protected]>

Continuing to use pci_host_common_probe() for the PCIe Root Complex on PolarFire SoC was leading to an extremely large _init() function and some unnatural code flow. Re-partition so some tasks are done in a _probe() routine, which calls pci_host_common_probe() and then use a much smaller _init() function, mainly to enable interrupts after address translation tables are set up.
...

+++ b/drivers/pci/controller/pcie-microchip-host.c

drivers/pci/controller/pcie-microchip-host.c +4 -0
@@ -384,6 +384,8 @@ static struct {
 
 static char poss_clks[][5] = { "fic0", "fic1", "fic2", "fic3" };
 
+static struct mc_pcie *port;
...
 
+static int mc_host_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
 	void __iomem *bridge_base_addr;
 	int ret;
 	u32 val;

drivers/pci/controller/pcie-microchip-host.c static int mc_platform_init(struct pci_config_window *cfg) · line 1141

Quoted 1 line
drivers/pci/controller/pcie-microchip-host.c +0 -0
@@ -1112,13 +1141,8 @@ static int mc_platform_init(struct pci_config_window *cfg)
 	port = devm_kzalloc(dev, sizeof(*port), GFP_KERNEL);

Saving this per-device pointer in a static singleton is kind of problematic. We may know there can only be a single instance right now, but even if that remains true forever for this driver, we don't want this pattern to be be copied elsewhere.

I didn't look hard enough to figure out exactly what problem this singleton solves, but is there any other way to address it?

I suspect it's related to using pci_host_common_probe(), and it's great to share that code, but it seems like that basically forces some non-ECAM initialization into the struct pci_ecam_ops.init() method where it doesn't really fit very well.

Bjorn

maintainer Applied
#9 lore raw
In reply to [email protected]
Quoted 9 lines · On Fri, 28 Jul 2023 14:13:54 +0100, [email protected] wrote:

This patch series contains fixes and clean-ups for the Microchip PolarFire SoC PCIe driver

These patches are extracted from the link below to separate them from the outbound and inbound range handling which is taking considerable time.

Resending with correct e-mail address list

[...]

Applied to controller/microchip, thanks!

[1/7] PCI: microchip: Correct the DED and SEC interrupt bit offsets

      https://git.kernel.org/pci/pci/c/6d473a5a2613
[2/7] PCI: microchip: Enable building driver as a module
      https://git.kernel.org/pci/pci/c/2e245bc8a2ab
[3/7] PCI: microchip: Align register, offset, and mask names with hw docs
      https://git.kernel.org/pci/pci/c/4d6bf4c49578
[4/7] PCI: microchip: Enable event handlers to access bridge and ctrl ptrs
      https://git.kernel.org/pci/pci/c/d1d6a0c9e79c
[5/7] PCI: microchip: Clean up initialisation of interrupts
      https://git.kernel.org/pci/pci/c/4f0b91247f78
[6/7] PCI: microchip: Gather MSI information from hardware config registers
      https://git.kernel.org/pci/pci/c/1abb722888fd
[7/7] PCI: microchip: Re-partition code between probe() and init()
      https://git.kernel.org/pci/pci/c/bac406c34fbc

Thanks,
Lorenzo

_______________________________________________
linux-riscv mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-riscv