Skip to contentSkip to conversation

hw/arm/virt: Avoid unexpected warning from Linux guest on host with Fujitsu CPUs

PATCH Superseded Zhenyu Zhang 2 participants 2 messages Jun 11, 2024

v2 of 3 Superseded Latest is v3 →

lore
Share & tools
lore
#0 lore raw

PATCH v2 1/1 hw/arm/virt: Avoid unexpected warning from Linux guest on host with Fujitsu CPUs

Multiple warning messages and corresponding backtraces are observed when Linux guest is booted on the host with Fujitsu CPUs. One of them is shown as below.

[    0.032443] ------------[ cut here ]------------
[    0.032446] uart-pl011 9000000.pl011: ARCH_DMA_MINALIGN smaller than
CTR_EL0.CWG (128 < 256)
[    0.032454] WARNING: CPU: 0 PID: 1 at arch/arm64/mm/dma-mapping.c:54
arch_setup_dma_ops+0xbc/0xcc
[    0.032470] Modules linked in:
[    0.032475] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.14.0-452.el9.aarch64
[    0.032481] Hardware name: linux,dummy-virt (DT)
[    0.032484] pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[    0.032490] pc : arch_setup_dma_ops+0xbc/0xcc
[    0.032496] lr : arch_setup_dma_ops+0xbc/0xcc
[    0.032501] sp : ffff80008003b860
[    0.032503] x29: ffff80008003b860 x28: 0000000000000000 x27: ffffaae4b949049c
[    0.032510] x26: 0000000000000000 x25: 0000000000000000 x24: 0000000000000000
[    0.032517] x23: 0000000000000100 x22: 0000000000000000 x21: 0000000000000000
[    0.032523] x20: 0000000100000000 x19: ffff2f06c02ea400 x18: ffffffffffffffff
[    0.032529] x17: 00000000208a5f76 x16: 000000006589dbcb x15: ffffaae4ba071c89
[    0.032535] x14: 0000000000000000 x13: ffffaae4ba071c84 x12: 455f525443206e61
[    0.032541] x11: 68742072656c6c61 x10: 0000000000000029 x9 : ffffaae4b7d21da4
[    0.032547] x8 : 0000000000000029 x7 : 4c414e494d5f414d x6 : 0000000000000029
[    0.032553] x5 : 000000000000000f x4 : ffffaae4b9617a00 x3 : 0000000000000001
[    0.032558] x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff2f06c029be40
[    0.032564] Call trace:
[    0.032566]  arch_setup_dma_ops+0xbc/0xcc
[    0.032572]  of_dma_configure_id+0x138/0x300
[    0.032591]  amba_dma_configure+0x34/0xc0
[    0.032600]  really_probe+0x78/0x3dc
[    0.032614]  __driver_probe_device+0x108/0x160
[    0.032619]  driver_probe_device+0x44/0x114
[    0.032624]  __device_attach_driver+0xb8/0x14c
[    0.032629]  bus_for_each_drv+0x88/0xe4
[    0.032634]  __device_attach+0xb0/0x1e0
[    0.032638]  device_initial_probe+0x18/0x20
[    0.032643]  bus_probe_device+0xa8/0xb0
[    0.032648]  device_add+0x4b4/0x6c0
[    0.032652]  amba_device_try_add.part.0+0x48/0x360
[    0.032657]  amba_device_add+0x104/0x144
[    0.032662]  of_amba_device_create.isra.0+0x100/0x1c4
[    0.032666]  of_platform_bus_create+0x294/0x35c
[    0.032669]  of_platform_populate+0x5c/0x150
[    0.032672]  of_platform_default_populate_init+0xd0/0xec
[    0.032697]  do_one_initcall+0x4c/0x2e0
[    0.032701]  do_initcalls+0x100/0x13c
[    0.032707]  kernel_init_freeable+0x1c8/0x21c
[    0.032712]  kernel_init+0x28/0x140
[    0.032731]  ret_from_fork+0x10/0x20
[    0.032735] ---[ end trace 0000000000000000 ]---

In Linux, a check is applied to every device which is exposed through device-tree node. The warning message is raised when the device isn't DMA coherent and the cache line size is larger than ARCH_DMA_MINALIGN (128 bytes). The cache line is sorted from CTR_EL0[CWG], which corresponds to 256 bytes on the guest CPUs. The DMA coherent capability is claimed through 'dma-coherent' property in their device-tree nodes or parent nodes.

Fix the issue by adding 'dma-coherent' property to the device-tree root node, meaning all devices are capable of DMA coherent by default.

---
 hw/arm/virt.c | 1 +
 1 file changed, 1 insertion(+)
hw/arm/virt.c +1 -0
index 3c93c0c0a6..0680b792bc 100644
@@ -270,6 +270,7 @@ static void create_fdt(VirtMachineState *vms)
     qemu_fdt_setprop_cell(fdt, "/", "#address-cells", 0x2);
     qemu_fdt_setprop_cell(fdt, "/", "#size-cells", 0x2);
     qemu_fdt_setprop_string(fdt, "/", "model", "linux,dummy-virt");
+    qemu_fdt_setprop(fdt, "/", "dma-coherent", NULL, 0);
 
     /* /chosen must exist for load_dtb to fill in necessary properties later */
     qemu_fdt_add_subnode(fdt, "/chosen");
Signature · 1 line
2.43.0
#1 lore raw
Quoted 72 lines · Zhenyu Zhang

Multiple warning messages and corresponding backtraces are observed when Linux guest is booted on the host with Fujitsu CPUs. One of them is shown as below.

[    0.032443] ------------[ cut here ]------------
[    0.032446] uart-pl011 9000000.pl011: ARCH_DMA_MINALIGN smaller than
CTR_EL0.CWG (128 < 256)
[    0.032454] WARNING: CPU: 0 PID: 1 at arch/arm64/mm/dma-mapping.c:54
arch_setup_dma_ops+0xbc/0xcc
[    0.032470] Modules linked in:
[    0.032475] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.14.0-452.el9.aarch64
[    0.032481] Hardware name: linux,dummy-virt (DT)
[    0.032484] pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[    0.032490] pc : arch_setup_dma_ops+0xbc/0xcc
[    0.032496] lr : arch_setup_dma_ops+0xbc/0xcc
[    0.032501] sp : ffff80008003b860
[    0.032503] x29: ffff80008003b860 x28: 0000000000000000 x27: ffffaae4b949049c
[    0.032510] x26: 0000000000000000 x25: 0000000000000000 x24: 0000000000000000
[    0.032517] x23: 0000000000000100 x22: 0000000000000000 x21: 0000000000000000
[    0.032523] x20: 0000000100000000 x19: ffff2f06c02ea400 x18: ffffffffffffffff
[    0.032529] x17: 00000000208a5f76 x16: 000000006589dbcb x15: ffffaae4ba071c89
[    0.032535] x14: 0000000000000000 x13: ffffaae4ba071c84 x12: 455f525443206e61
[    0.032541] x11: 68742072656c6c61 x10: 0000000000000029 x9 : ffffaae4b7d21da4
[    0.032547] x8 : 0000000000000029 x7 : 4c414e494d5f414d x6 : 0000000000000029
[    0.032553] x5 : 000000000000000f x4 : ffffaae4b9617a00 x3 : 0000000000000001
[    0.032558] x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff2f06c029be40
[    0.032564] Call trace:
[    0.032566]  arch_setup_dma_ops+0xbc/0xcc
[    0.032572]  of_dma_configure_id+0x138/0x300
[    0.032591]  amba_dma_configure+0x34/0xc0
[    0.032600]  really_probe+0x78/0x3dc
[    0.032614]  __driver_probe_device+0x108/0x160
[    0.032619]  driver_probe_device+0x44/0x114
[    0.032624]  __device_attach_driver+0xb8/0x14c
[    0.032629]  bus_for_each_drv+0x88/0xe4
[    0.032634]  __device_attach+0xb0/0x1e0
[    0.032638]  device_initial_probe+0x18/0x20
[    0.032643]  bus_probe_device+0xa8/0xb0
[    0.032648]  device_add+0x4b4/0x6c0
[    0.032652]  amba_device_try_add.part.0+0x48/0x360
[    0.032657]  amba_device_add+0x104/0x144
[    0.032662]  of_amba_device_create.isra.0+0x100/0x1c4
[    0.032666]  of_platform_bus_create+0x294/0x35c
[    0.032669]  of_platform_populate+0x5c/0x150
[    0.032672]  of_platform_default_populate_init+0xd0/0xec
[    0.032697]  do_one_initcall+0x4c/0x2e0
[    0.032701]  do_initcalls+0x100/0x13c
[    0.032707]  kernel_init_freeable+0x1c8/0x21c
[    0.032712]  kernel_init+0x28/0x140
[    0.032731]  ret_from_fork+0x10/0x20
[    0.032735] ---[ end trace 0000000000000000 ]---

In Linux, a check is applied to every device which is exposed through device-tree node. The warning message is raised when the device isn't DMA coherent and the cache line size is larger than ARCH_DMA_MINALIGN (128 bytes). The cache line is sorted from CTR_EL0[CWG], which corresponds to 256 bytes on the guest CPUs. The DMA coherent capability is claimed through 'dma-coherent' property in their device-tree nodes or parent nodes.

Fix the issue by adding 'dma-coherent' property to the device-tree root node, meaning all devices are capable of DMA coherent by default.

---
 hw/arm/virt.c | 1 +
 1 file changed, 1 insertion(+)
hw/arm/virt.c +0 -0
index 3c93c0c0a6..0680b792bc 100644

hw/arm/virt.c static void create_fdt(VirtMachineState *vms) · line 272

Quoted 3 lines
hw/arm/virt.c +0 -0
@@ -270,6 +270,7 @@ static void create_fdt(VirtMachineState *vms)
     qemu_fdt_setprop_cell(fdt, "/", "#address-cells", 0x2);
     qemu_fdt_setprop_cell(fdt, "/", "#size-cells", 0x2);
     qemu_fdt_setprop_string(fdt, "/", "model", "linux,dummy-virt");

We should have a comment explaining why we do this:

/*
* For QEMU, all DMA is coherent. Advertising this in the root node
* has two benefits:
* - it avoids potential bugs where we forget to mark a DMA
* capable device as being dma-coherent
* - it avoids spurious warnings from the Linux kernel about
* devices which can't do DMA at all
*/

hw/arm/virt.c static void create_fdt(VirtMachineState *vms) · line 276

Quoted 4 lines
hw/arm/virt.c +1 -0
+    qemu_fdt_setprop(fdt, "/", "dma-coherent", NULL, 0);
 
     /* /chosen must exist for load_dtb to fill in necessary properties later */
     qemu_fdt_add_subnode(fdt, "/chosen");

thanks
-- PMM