Skip to contentSkip to conversation

leds: trigger: input-events: Rewrite to fix a serious locking issue

PATCH Applied Hans de Goede 2 participants 5 messages Jun 2, 2024 – Jun 20, 2024 LED

lore
Share & tools
lore
#0 lore raw

cover leds: trigger: input-events: Rewrite to fix a serious locking issue

Hi All,

As first discussed here:
https://lore.kernel.org/linux-leds/[email protected]/

Shortly after ledtrig-input-events being merged into leds-for-next I found a serious locking issue with it :|

The single patch in this series fixes this. As indicated in the subject this is close to a full rewrite of ledtrig-input-events. The core functionality is preserved and since ledtrig-input-events ATM only exists on leds-for-next the other behavioral changes involved are not a problem.

Lee, I personally think it makes sense to keep the history and apply this on top (1). But if you prefer you could also drop the current version and then I'll send out a new patch directly adding the new version of the input-events trigger.

Regards,

Hans

1) Especially in the light of the similar issues in the netdev trigger

Hans de Goede (1):
leds: trigger: input-events: Rewrite to fix a serious locking issue

 drivers/leds/trigger/ledtrig-input-events.c | 136 +++++---------------
 1 file changed, 34 insertions(+), 102 deletions(-)
Signature · 1 line
2.45.1
#1 lore raw

PATCH 1/1 leds: trigger: input-events: Rewrite to fix a serious locking issue

The input subsystem registers LEDs with default triggers while holding the input_lock and input_register_handler() takes the input_lock this means that a triggers activate method cannot directly call input_register_handler() as the old ledtrig-input-events code is doing.

The initial implementation of the input-events trigger mainly did not use the simple LED trigger mechanism because that mechanism had an issue with the initial state of a newly activated LED not matching the last led_trigger_event() call for the trigger. This issue has been fixed in commit 822c91e72eac ("leds: trigger: Store brightness set by led_trigger_event()").

Rewrite the "input-events" trigger to use the simple LED trigger mechanism, registering a single input_handler at module_init() time and using led_trigger_event() to set the brightness for all LEDs controlled by this trigger.

Compared to the old code this looses the ability for the user to configure a different brightness for the on state then LED_FULL, this is standard for simple LED triggers and since this trigger is only in for-leds-next ATM losing that functionality is not a regression.

This also changes the configurability of the LED off timeout from a per LED setting to a global setting (runtime modifiable module-parameter).

Switching to registering a single input_handler at module_init() time fixes the following locking issue reported by lockdep:

[ 2840.220145] usb 1-1.3: new low-speed USB device number 3 using xhci_hcd
[ 2840.307172] usb 1-1.3: New USB device found, idVendor=0603, idProduct=0002, bcdDevice= 2.21
[ 2840.307375] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2840.307423] usb 1-1.3: Product: USB Composite Device
[ 2840.307456] usb 1-1.3: Manufacturer: SINO WEALTH
[ 2840.333985] input: SINO WEALTH USB Composite Device as /devices/pci0000:00/0000:00:14.0/usb1/1-1/1-1.3/1-1.3:1.0/0003:0603:0002.0007/input/input19
[ 2840.386545] ======================================================
[ 2840.386549] WARNING: possible circular locking dependency detected
[ 2840.386554] 6.10.0-rc1+ #97 Tainted: G         C  E
[ 2840.386558] ------------------------------------------------------
[ 2840.386562] kworker/1:1/52 is trying to acquire lock:
[ 2840.386566] ffff98fcf1629300 (&led_cdev->led_access){+.+.}-{3:3}, at: led_classdev_register_ext+0x1c6/0x380
[ 2840.386590]
               but task is already holding lock:
[ 2840.386593] ffffffff88130cc8 (input_mutex){+.+.}-{3:3}, at: input_register_device.cold+0x47/0x150
[ 2840.386608]
               which lock already depends on the new lock.
[ 2840.386611]
               the existing dependency chain (in reverse order) is:
[ 2840.386615]
               -> #3 (input_mutex){+.+.}-{3:3}:
[ 2840.386624]        __mutex_lock+0x8c/0xc10
[ 2840.386634]        input_register_handler+0x1c/0xf0
[ 2840.386641]        0xffffffffc142c437
[ 2840.386655]        led_trigger_set+0x1e1/0x2e0
[ 2840.386661]        led_trigger_register+0x170/0x1b0
[ 2840.386666]        do_one_initcall+0x5e/0x3a0
[ 2840.386675]        do_init_module+0x60/0x220
[ 2840.386683]        __do_sys_init_module+0x15f/0x190
[ 2840.386689]        do_syscall_64+0x93/0x180
[ 2840.386696]        entry_SYSCALL_64_after_hwframe+0x76/0x7e
[ 2840.386705]
               -> #2 (&led_cdev->trigger_lock){+.+.}-{3:3}:
[ 2840.386714]        down_write+0x3b/0xd0
[ 2840.386720]        led_trigger_register+0x12c/0x1b0
[ 2840.386725]        rfkill_register+0xec/0x340 [rfkill]
[ 2840.386739]        wiphy_register+0x82a/0x930 [cfg80211]
[ 2840.386907]        brcmf_cfg80211_attach+0xcbd/0x1430 [brcmfmac]
[ 2840.386952]        brcmf_attach+0x1ba/0x4c0 [brcmfmac]
[ 2840.386991]        brcmf_pcie_setup+0x899/0xc70 [brcmfmac]
[ 2840.387030]        brcmf_fw_request_done+0x13b/0x180 [brcmfmac]
[ 2840.387070]        request_firmware_work_func+0x3b/0x70
[ 2840.387078]        process_one_work+0x21a/0x590
[ 2840.387085]        worker_thread+0x1d1/0x3e0
[ 2840.387090]        kthread+0xee/0x120
[ 2840.387096]        ret_from_fork+0x30/0x50
[ 2840.387105]        ret_from_fork_asm+0x1a/0x30
[ 2840.387112]
               -> #1 (leds_list_lock){++++}-{3:3}:
[ 2840.387123]        down_write+0x3b/0xd0
[ 2840.387129]        led_classdev_register_ext+0x29e/0x380
[ 2840.387134]        0xffffffffc0e6b74c
[ 2840.387143]        platform_probe+0x40/0xa0
[ 2840.387151]        really_probe+0xde/0x340
[ 2840.387157]        __driver_probe_device+0x78/0x110
[ 2840.387162]        driver_probe_device+0x1f/0xa0
[ 2840.387168]        __driver_attach+0xba/0x1c0
[ 2840.387173]        bus_for_each_dev+0x6b/0xb0
[ 2840.387180]        bus_add_driver+0x111/0x1f0
[ 2840.387185]        driver_register+0x6e/0xc0
[ 2840.387191]        do_one_initcall+0x5e/0x3a0
[ 2840.387197]        do_init_module+0x60/0x220
[ 2840.387204]        __do_sys_init_module+0x15f/0x190
[ 2840.387210]        do_syscall_64+0x93/0x180
[ 2840.387217]        entry_SYSCALL_64_after_hwframe+0x76/0x7e
[ 2840.387224]
               -> #0 (&led_cdev->led_access){+.+.}-{3:3}:
[ 2840.387233]        __lock_acquire+0x11c6/0x1f20
[ 2840.387239]        lock_acquire+0xc8/0x2b0
[ 2840.387244]        __mutex_lock+0x8c/0xc10
[ 2840.387251]        led_classdev_register_ext+0x1c6/0x380
[ 2840.387256]        input_leds_connect+0x139/0x260
[ 2840.387262]        input_attach_handler.isra.0+0x75/0x90
[ 2840.387268]        input_register_device.cold+0xa1/0x150
[ 2840.387274]        hidinput_connect+0x848/0xb00
[ 2840.387280]        hid_connect+0x567/0x5a0
[ 2840.387288]        hid_hw_start+0x3f/0x60
[ 2840.387294]        hid_device_probe+0x10d/0x190
[ 2840.387298]        really_probe+0xde/0x340
[ 2840.387304]        __driver_probe_device+0x78/0x110
[ 2840.387309]        driver_probe_device+0x1f/0xa0
[ 2840.387314]        __device_attach_driver+0x85/0x110
[ 2840.387320]        bus_for_each_drv+0x78/0xc0
[ 2840.387326]        __device_attach+0xb0/0x1b0
[ 2840.387332]        bus_probe_device+0x94/0xb0
[ 2840.387337]        device_add+0x64a/0x860
[ 2840.387343]        hid_add_device+0xe5/0x240
[ 2840.387349]        usbhid_probe+0x4bb/0x600
[ 2840.387356]        usb_probe_interface+0xea/0x2b0
[ 2840.387363]        really_probe+0xde/0x340
[ 2840.387368]        __driver_probe_device+0x78/0x110
[ 2840.387373]        driver_probe_device+0x1f/0xa0
[ 2840.387378]        __device_attach_driver+0x85/0x110
[ 2840.387383]        bus_for_each_drv+0x78/0xc0
[ 2840.387390]        __device_attach+0xb0/0x1b0
[ 2840.387395]        bus_probe_device+0x94/0xb0
[ 2840.387400]        device_add+0x64a/0x860
[ 2840.387405]        usb_set_configuration+0x5e8/0x880
[ 2840.387411]        usb_generic_driver_probe+0x3e/0x60
[ 2840.387418]        usb_probe_device+0x3d/0x120
[ 2840.387423]        really_probe+0xde/0x340
[ 2840.387428]        __driver_probe_device+0x78/0x110
[ 2840.387434]        driver_probe_device+0x1f/0xa0
[ 2840.387439]        __device_attach_driver+0x85/0x110
[ 2840.387444]        bus_for_each_drv+0x78/0xc0
[ 2840.387451]        __device_attach+0xb0/0x1b0
[ 2840.387456]        bus_probe_device+0x94/0xb0
[ 2840.387461]        device_add+0x64a/0x860
[ 2840.387466]        usb_new_device.cold+0x141/0x38f
[ 2840.387473]        hub_event+0x1166/0x1980
[ 2840.387479]        process_one_work+0x21a/0x590
[ 2840.387484]        worker_thread+0x1d1/0x3e0
[ 2840.387488]        kthread+0xee/0x120
[ 2840.387493]        ret_from_fork+0x30/0x50
[ 2840.387500]        ret_from_fork_asm+0x1a/0x30
[ 2840.387506]
               other info that might help us debug this:
[ 2840.387509] Chain exists of:
                 &led_cdev->led_access --> &led_cdev->trigger_lock --> input_mutex
[ 2840.387520]  Possible unsafe locking scenario:
[ 2840.387523]        CPU0                    CPU1
[ 2840.387526]        ----                    ----
[ 2840.387529]   lock(input_mutex);
[ 2840.387534]                                lock(&led_cdev->trigger_lock);
[ 2840.387540]                                lock(input_mutex);
[ 2840.387545]   lock(&led_cdev->led_access);
[ 2840.387550]
                *** DEADLOCK ***
[ 2840.387552] 7 locks held by kworker/1:1/52:
[ 2840.387557]  #0: ffff98fcc1d07148 ((wq_completion)usb_hub_wq){+.+.}-{0:0}, at: process_one_work+0x4af/0x590
[ 2840.387570]  #1: ffffb67e00213e60 ((work_completion)(&hub->events)){+.+.}-{0:0}, at: process_one_work+0x1d5/0x590
[ 2840.387583]  #2: ffff98fcc6582190 (&dev->mutex){....}-{3:3}, at: hub_event+0x57/0x1980
[ 2840.387596]  #3: ffff98fccb3c6990 (&dev->mutex){....}-{3:3}, at: __device_attach+0x26/0x1b0
[ 2840.387610]  #4: ffff98fcc5260960 (&dev->mutex){....}-{3:3}, at: __device_attach+0x26/0x1b0
[ 2840.387622]  #5: ffff98fce3999a20 (&dev->mutex){....}-{3:3}, at: __device_attach+0x26/0x1b0
[ 2840.387635]  #6: ffffffff88130cc8 (input_mutex){+.+.}-{3:3}, at: input_register_device.cold+0x47/0x150
[ 2840.387649]
               stack backtrace:
[ 2840.387653] CPU: 1 PID: 52 Comm: kworker/1:1 Tainted: G         C  E      6.10.0-rc1+ #97
[ 2840.387659] Hardware name: Xiaomi Inc Mipad2/Mipad, BIOS MIPad-P4.X64.0043.R03.1603071414 03/07/2016
[ 2840.387665] Workqueue: usb_hub_wq hub_event
[ 2840.387674] Call Trace:
[ 2840.387681]  <TASK>
[ 2840.387689]  dump_stack_lvl+0x68/0x90
[ 2840.387700]  check_noncircular+0x10d/0x120
[ 2840.387710]  ? register_lock_class+0x38/0x480
[ 2840.387717]  ? check_noncircular+0x74/0x120
[ 2840.387727]  __lock_acquire+0x11c6/0x1f20
[ 2840.387736]  lock_acquire+0xc8/0x2b0
[ 2840.387743]  ? led_classdev_register_ext+0x1c6/0x380
[ 2840.387753]  __mutex_lock+0x8c/0xc10
[ 2840.387760]  ? led_classdev_register_ext+0x1c6/0x380
[ 2840.387766]  ? _raw_spin_unlock_irqrestore+0x35/0x60
[ 2840.387773]  ? klist_next+0x158/0x160
[ 2840.387781]  ? led_classdev_register_ext+0x1c6/0x380
[ 2840.387787]  ? lockdep_init_map_type+0x58/0x250
[ 2840.387796]  ? led_classdev_register_ext+0x1c6/0x380
[ 2840.387802]  led_classdev_register_ext+0x1c6/0x380
[ 2840.387810]  ? kvasprintf+0x70/0xb0
[ 2840.387820]  ? kasprintf+0x3e/0x50
[ 2840.387829]  input_leds_connect+0x139/0x260
[ 2840.387838]  input_attach_handler.isra.0+0x75/0x90
[ 2840.387846]  input_register_device.cold+0xa1/0x150
[ 2840.387854]  hidinput_connect+0x848/0xb00
[ 2840.387862]  ? usbhid_start+0x45b/0x7b0
[ 2840.387870]  hid_connect+0x567/0x5a0
[ 2840.387878]  ? __mutex_unlock_slowpath+0x2d/0x260
[ 2840.387891]  hid_hw_start+0x3f/0x60
[ 2840.387899]  hid_device_probe+0x10d/0x190
[ 2840.387906]  ? __pfx___device_attach_driver+0x10/0x10
[ 2840.387913]  really_probe+0xde/0x340
[ 2840.387919]  ? pm_runtime_barrier+0x50/0x90
[ 2840.387927]  __driver_probe_device+0x78/0x110
[ 2840.387934]  driver_probe_device+0x1f/0xa0
[ 2840.387941]  __device_attach_driver+0x85/0x110
[ 2840.387949]  bus_for_each_drv+0x78/0xc0
[ 2840.387959]  __device_attach+0xb0/0x1b0
[ 2840.387967]  bus_probe_device+0x94/0xb0
[ 2840.387974]  device_add+0x64a/0x860
[ 2840.387982]  ? __debugfs_create_file+0x14a/0x1c0
[ 2840.387993]  hid_add_device+0xe5/0x240
[ 2840.388002]  usbhid_probe+0x4bb/0x600
[ 2840.388013]  usb_probe_interface+0xea/0x2b0
[ 2840.388021]  ? __pfx___device_attach_driver+0x10/0x10
[ 2840.388028]  really_probe+0xde/0x340
[ 2840.388034]  ? pm_runtime_barrier+0x50/0x90
[ 2840.388040]  __driver_probe_device+0x78/0x110
[ 2840.388048]  driver_probe_device+0x1f/0xa0
[ 2840.388055]  __device_attach_driver+0x85/0x110
[ 2840.388062]  bus_for_each_drv+0x78/0xc0
[ 2840.388071]  __device_attach+0xb0/0x1b0
[ 2840.388079]  bus_probe_device+0x94/0xb0
[ 2840.388086]  device_add+0x64a/0x860
[ 2840.388094]  ? __mutex_unlock_slowpath+0x2d/0x260
[ 2840.388103]  usb_set_configuration+0x5e8/0x880
[ 2840.388114]  ? __pfx___device_attach_driver+0x10/0x10
[ 2840.388121]  usb_generic_driver_probe+0x3e/0x60
[ 2840.388129]  usb_probe_device+0x3d/0x120
[ 2840.388137]  really_probe+0xde/0x340
[ 2840.388142]  ? pm_runtime_barrier+0x50/0x90
[ 2840.388149]  __driver_probe_device+0x78/0x110
[ 2840.388156]  driver_probe_device+0x1f/0xa0
[ 2840.388163]  __device_attach_driver+0x85/0x110
[ 2840.388171]  bus_for_each_drv+0x78/0xc0
[ 2840.388180]  __device_attach+0xb0/0x1b0
[ 2840.388188]  bus_probe_device+0x94/0xb0
[ 2840.388195]  device_add+0x64a/0x860
[ 2840.388202]  ? lockdep_hardirqs_on+0x78/0x100
[ 2840.388210]  ? _raw_spin_unlock_irqrestore+0x35/0x60
[ 2840.388219]  usb_new_device.cold+0x141/0x38f
[ 2840.388227]  hub_event+0x1166/0x1980
[ 2840.388242]  process_one_work+0x21a/0x590
[ 2840.388249]  ? move_linked_works+0x70/0xa0
[ 2840.388260]  worker_thread+0x1d1/0x3e0
[ 2840.388268]  ? __pfx_worker_thread+0x10/0x10
[ 2840.388273]  kthread+0xee/0x120
[ 2840.388279]  ? __pfx_kthread+0x10/0x10
[ 2840.388287]  ret_from_fork+0x30/0x50
[ 2840.388294]  ? __pfx_kthread+0x10/0x10
[ 2840.388301]  ret_from_fork_asm+0x1a/0x30
[ 2840.388315]  </TASK>
[ 2840.415630] hid-generic 0003:0603:0002.0007: input,hidraw6: USB HID v1.10 Keyboard [SINO WEALTH USB Composite Device] on usb-0000:00:14.0-1.3/input0
---
 drivers/leds/trigger/ledtrig-input-events.c | 136 +++++---------------
 1 file changed, 34 insertions(+), 102 deletions(-)
drivers/leds/trigger/ledtrig-input-events.c +34 -102
index 1de0176799f9..1c79731562c2 100644
@@ -3,31 +3,32 @@
  * Input Events LED trigger
  *
  * Copyright (C) 2024 Hans de Goede <[email protected]>
- * Partially based on Atsushi Nemoto's ledtrig-heartbeat.c.
  */
 
 #include <linux/input.h>
 #include <linux/jiffies.h>
 #include <linux/leds.h>
 #include <linux/module.h>
+#include <linux/moduleparam.h>
 #include <linux/slab.h>
 #include <linux/spinlock.h>
 #include <linux/workqueue.h>
 #include "../leds.h"
 
-#define DEFAULT_LED_OFF_DELAY_MS			5000
+static unsigned long led_off_delay_ms = 5000;
+module_param(led_off_delay_ms, ulong, 0644);
+MODULE_PARM_DESC(led_off_delay_ms,
+	"Specify delay in ms for turning LEDs off after last input event");
 
-struct input_events_data {
-	struct input_handler handler;
+static struct input_events_data {
 	struct delayed_work work;
 	spinlock_t lock;
-	struct led_classdev *led_cdev;
-	int led_cdev_saved_flags;
 	/* To avoid repeatedly setting the brightness while there are events */
 	bool led_on;
 	unsigned long led_off_time;
-	unsigned long led_off_delay;
-};
+} input_events_data;
+
+static struct led_trigger *input_events_led_trigger;
 
 static void led_input_events_work(struct work_struct *work)
 {
@@ -41,62 +42,24 @@ static void led_input_events_work(struct work_struct *work)
 	 * running before a new event pushed led_off_time back.
 	 */
 	if (time_after_eq(jiffies, data->led_off_time)) {
-		led_set_brightness_nosleep(data->led_cdev, LED_OFF);
+		led_trigger_event(input_events_led_trigger, LED_OFF);
 		data->led_on = false;
 	}
 
 	spin_unlock_irq(&data->lock);
 }
 
-static ssize_t delay_show(struct device *dev, struct device_attribute *attr, char *buf)
-{
-	struct input_events_data *input_events_data = led_trigger_get_drvdata(dev);
-
-	return sysfs_emit(buf, "%lu\n", input_events_data->led_off_delay);
-}
-
-static ssize_t delay_store(struct device *dev, struct device_attribute *attr,
-			   const char *buf, size_t size)
-{
-	struct input_events_data *input_events_data = led_trigger_get_drvdata(dev);
-	unsigned long delay;
-	int ret;
-
-	ret = kstrtoul(buf, 0, &delay);
-	if (ret)
-		return ret;
-
-	/* Clamp between 0.5 and 1000 seconds */
-	delay = clamp_val(delay, 500UL, 1000000UL);
-	input_events_data->led_off_delay = msecs_to_jiffies(delay);
-
-	return size;
-}
-
-static DEVICE_ATTR_RW(delay);
-
-static struct attribute *input_events_led_attrs[] = {
-	&dev_attr_delay.attr,
-	NULL
-};
-ATTRIBUTE_GROUPS(input_events_led);
-
 static void input_events_event(struct input_handle *handle, unsigned int type,
 			       unsigned int code, int val)
 {
-	struct input_events_data *data =
-		container_of(handle->handler, struct input_events_data, handler);
-	unsigned long led_off_delay = READ_ONCE(data->led_off_delay);
-	struct led_classdev *led_cdev = data->led_cdev;
+	struct input_events_data *data = &input_events_data;
+	unsigned long led_off_delay = msecs_to_jiffies(led_off_delay_ms);
 	unsigned long flags;
 
-	if (test_and_clear_bit(LED_BLINK_BRIGHTNESS_CHANGE, &led_cdev->work_flags))
-		led_cdev->blink_brightness = led_cdev->new_blink_brightness;
-
 	spin_lock_irqsave(&data->lock, flags);
 
 	if (!data->led_on) {
-		led_set_brightness_nosleep(led_cdev, led_cdev->blink_brightness);
+		led_trigger_event(input_events_led_trigger, LED_FULL);
 		data->led_on = true;
 	}
 	data->led_off_time = jiffies + led_off_delay;
@@ -118,7 +81,7 @@ static int input_events_connect(struct input_handler *handler, struct input_dev
 
 	handle->dev = dev;
 	handle->handler = handler;
-	handle->name = "input-events";
+	handle->name = KBUILD_MODNAME;
 
 	ret = input_register_handle(handle);
 	if (ret)
@@ -160,72 +123,41 @@ static const struct input_device_id input_events_ids[] = {
 	{ }
 };
 
-static int input_events_activate(struct led_classdev *led_cdev)
+static struct input_handler input_events_handler = {
+	.name = KBUILD_MODNAME,
+	.event = input_events_event,
+	.connect = input_events_connect,
+	.disconnect = input_events_disconnect,
+	.id_table = input_events_ids,
+};
+
+static int __init input_events_init(void)
 {
-	struct input_events_data *data;
 	int ret;
 
-	data = kzalloc(sizeof(*data), GFP_KERNEL);
-	if (!data)
-		return -ENOMEM;
+	INIT_DELAYED_WORK(&input_events_data.work, led_input_events_work);
+	spin_lock_init(&input_events_data.lock);
 
-	data->handler.name = "input-events";
-	data->handler.event = input_events_event;
-	data->handler.connect = input_events_connect;
-	data->handler.disconnect = input_events_disconnect;
-	data->handler.id_table = input_events_ids;
+	led_trigger_register_simple("input-events", &input_events_led_trigger);
 
-	INIT_DELAYED_WORK(&data->work, led_input_events_work);
-	spin_lock_init(&data->lock);
-
-	data->led_cdev = led_cdev;
-	data->led_cdev_saved_flags = led_cdev->flags;
-	data->led_off_delay = msecs_to_jiffies(DEFAULT_LED_OFF_DELAY_MS);
-
-	/*
-	 * Use led_cdev->blink_brightness + LED_BLINK_SW flag so that sysfs
-	 * brightness writes will change led_cdev->new_blink_brightness for
-	 * configuring the on state brightness (like ledtrig-heartbeat).
-	 */
-	if (!led_cdev->blink_brightness)
-		led_cdev->blink_brightness = led_cdev->max_brightness;
-
-	/* Start with LED off */
-	led_set_brightness_nosleep(data->led_cdev, LED_OFF);
-
-	ret = input_register_handler(&data->handler);
+	ret = input_register_handler(&input_events_handler);
 	if (ret) {
-		kfree(data);
+		led_trigger_unregister_simple(input_events_led_trigger);
 		return ret;
 	}
 
-	set_bit(LED_BLINK_SW, &led_cdev->work_flags);
-
-	/* Turn LED off during suspend, original flags are restored on deactivate() */
-	led_cdev->flags |= LED_CORE_SUSPENDRESUME;
-
-	led_set_trigger_data(led_cdev, data);
 	return 0;
 }
 
-static void input_events_deactivate(struct led_classdev *led_cdev)
+static void __exit input_events_exit(void)
 {
-	struct input_events_data *data = led_get_trigger_data(led_cdev);
-
-	led_cdev->flags = data->led_cdev_saved_flags;
-	clear_bit(LED_BLINK_SW, &led_cdev->work_flags);
-	input_unregister_handler(&data->handler);
-	cancel_delayed_work_sync(&data->work);
-	kfree(data);
+	input_unregister_handler(&input_events_handler);
+	cancel_delayed_work_sync(&input_events_data.work);
+	led_trigger_unregister_simple(input_events_led_trigger);
 }
 
-static struct led_trigger input_events_led_trigger = {
-	.name       = "input-events",
-	.activate   = input_events_activate,
-	.deactivate = input_events_deactivate,
-	.groups     = input_events_led_groups,
-};
-module_led_trigger(input_events_led_trigger);
+module_init(input_events_init);
+module_exit(input_events_exit);
 
 MODULE_AUTHOR("Hans de Goede <[email protected]>");
 MODULE_DESCRIPTION("Input Events LED trigger");
Signature · 1 line
2.45.1
maintainer
#2 lore raw
Quoted 248 lines · Hans de Goede

The input subsystem registers LEDs with default triggers while holding the input_lock and input_register_handler() takes the input_lock this means that a triggers activate method cannot directly call input_register_handler() as the old ledtrig-input-events code is doing.

The initial implementation of the input-events trigger mainly did not use the simple LED trigger mechanism because that mechanism had an issue with the initial state of a newly activated LED not matching the last led_trigger_event() call for the trigger. This issue has been fixed in commit 822c91e72eac ("leds: trigger: Store brightness set by led_trigger_event()").

Rewrite the "input-events" trigger to use the simple LED trigger mechanism, registering a single input_handler at module_init() time and using led_trigger_event() to set the brightness for all LEDs controlled by this trigger.

Compared to the old code this looses the ability for the user to configure a different brightness for the on state then LED_FULL, this is standard for simple LED triggers and since this trigger is only in for-leds-next ATM losing that functionality is not a regression.

This also changes the configurability of the LED off timeout from a per LED setting to a global setting (runtime modifiable module-parameter).

Switching to registering a single input_handler at module_init() time fixes the following locking issue reported by lockdep:

[ 2840.220145] usb 1-1.3: new low-speed USB device number 3 using xhci_hcd
[ 2840.307172] usb 1-1.3: New USB device found, idVendor=0603, idProduct=0002, bcdDevice= 2.21
[ 2840.307375] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2840.307423] usb 1-1.3: Product: USB Composite Device
[ 2840.307456] usb 1-1.3: Manufacturer: SINO WEALTH
[ 2840.333985] input: SINO WEALTH USB Composite Device as /devices/pci0000:00/0000:00:14.0/usb1/1-1/1-1.3/1-1.3:1.0/0003:0603:0002.0007/input/input19
[ 2840.386545] ======================================================
[ 2840.386549] WARNING: possible circular locking dependency detected
[ 2840.386554] 6.10.0-rc1+ #97 Tainted: G         C  E
[ 2840.386558] ------------------------------------------------------
[ 2840.386562] kworker/1:1/52 is trying to acquire lock:
[ 2840.386566] ffff98fcf1629300 (&led_cdev->led_access){+.+.}-{3:3}, at: led_classdev_register_ext+0x1c6/0x380
[ 2840.386590]
               but task is already holding lock:
[ 2840.386593] ffffffff88130cc8 (input_mutex){+.+.}-{3:3}, at: input_register_device.cold+0x47/0x150
[ 2840.386608]
               which lock already depends on the new lock.
[ 2840.386611]
               the existing dependency chain (in reverse order) is:
[ 2840.386615]
               -> #3 (input_mutex){+.+.}-{3:3}:
[ 2840.386624]        __mutex_lock+0x8c/0xc10
[ 2840.386634]        input_register_handler+0x1c/0xf0
[ 2840.386641]        0xffffffffc142c437
[ 2840.386655]        led_trigger_set+0x1e1/0x2e0
[ 2840.386661]        led_trigger_register+0x170/0x1b0
[ 2840.386666]        do_one_initcall+0x5e/0x3a0
[ 2840.386675]        do_init_module+0x60/0x220
[ 2840.386683]        __do_sys_init_module+0x15f/0x190
[ 2840.386689]        do_syscall_64+0x93/0x180
[ 2840.386696]        entry_SYSCALL_64_after_hwframe+0x76/0x7e
[ 2840.386705]
               -> #2 (&led_cdev->trigger_lock){+.+.}-{3:3}:
[ 2840.386714]        down_write+0x3b/0xd0
[ 2840.386720]        led_trigger_register+0x12c/0x1b0
[ 2840.386725]        rfkill_register+0xec/0x340 [rfkill]
[ 2840.386739]        wiphy_register+0x82a/0x930 [cfg80211]
[ 2840.386907]        brcmf_cfg80211_attach+0xcbd/0x1430 [brcmfmac]
[ 2840.386952]        brcmf_attach+0x1ba/0x4c0 [brcmfmac]
[ 2840.386991]        brcmf_pcie_setup+0x899/0xc70 [brcmfmac]
[ 2840.387030]        brcmf_fw_request_done+0x13b/0x180 [brcmfmac]
[ 2840.387070]        request_firmware_work_func+0x3b/0x70
[ 2840.387078]        process_one_work+0x21a/0x590
[ 2840.387085]        worker_thread+0x1d1/0x3e0
[ 2840.387090]        kthread+0xee/0x120
[ 2840.387096]        ret_from_fork+0x30/0x50
[ 2840.387105]        ret_from_fork_asm+0x1a/0x30
[ 2840.387112]
               -> #1 (leds_list_lock){++++}-{3:3}:
[ 2840.387123]        down_write+0x3b/0xd0
[ 2840.387129]        led_classdev_register_ext+0x29e/0x380
[ 2840.387134]        0xffffffffc0e6b74c
[ 2840.387143]        platform_probe+0x40/0xa0
[ 2840.387151]        really_probe+0xde/0x340
[ 2840.387157]        __driver_probe_device+0x78/0x110
[ 2840.387162]        driver_probe_device+0x1f/0xa0
[ 2840.387168]        __driver_attach+0xba/0x1c0
[ 2840.387173]        bus_for_each_dev+0x6b/0xb0
[ 2840.387180]        bus_add_driver+0x111/0x1f0
[ 2840.387185]        driver_register+0x6e/0xc0
[ 2840.387191]        do_one_initcall+0x5e/0x3a0
[ 2840.387197]        do_init_module+0x60/0x220
[ 2840.387204]        __do_sys_init_module+0x15f/0x190
[ 2840.387210]        do_syscall_64+0x93/0x180
[ 2840.387217]        entry_SYSCALL_64_after_hwframe+0x76/0x7e
[ 2840.387224]
               -> #0 (&led_cdev->led_access){+.+.}-{3:3}:
[ 2840.387233]        __lock_acquire+0x11c6/0x1f20
[ 2840.387239]        lock_acquire+0xc8/0x2b0
[ 2840.387244]        __mutex_lock+0x8c/0xc10
[ 2840.387251]        led_classdev_register_ext+0x1c6/0x380
[ 2840.387256]        input_leds_connect+0x139/0x260
[ 2840.387262]        input_attach_handler.isra.0+0x75/0x90
[ 2840.387268]        input_register_device.cold+0xa1/0x150
[ 2840.387274]        hidinput_connect+0x848/0xb00
[ 2840.387280]        hid_connect+0x567/0x5a0
[ 2840.387288]        hid_hw_start+0x3f/0x60
[ 2840.387294]        hid_device_probe+0x10d/0x190
[ 2840.387298]        really_probe+0xde/0x340
[ 2840.387304]        __driver_probe_device+0x78/0x110
[ 2840.387309]        driver_probe_device+0x1f/0xa0
[ 2840.387314]        __device_attach_driver+0x85/0x110
[ 2840.387320]        bus_for_each_drv+0x78/0xc0
[ 2840.387326]        __device_attach+0xb0/0x1b0
[ 2840.387332]        bus_probe_device+0x94/0xb0
[ 2840.387337]        device_add+0x64a/0x860
[ 2840.387343]        hid_add_device+0xe5/0x240
[ 2840.387349]        usbhid_probe+0x4bb/0x600
[ 2840.387356]        usb_probe_interface+0xea/0x2b0
[ 2840.387363]        really_probe+0xde/0x340
[ 2840.387368]        __driver_probe_device+0x78/0x110
[ 2840.387373]        driver_probe_device+0x1f/0xa0
[ 2840.387378]        __device_attach_driver+0x85/0x110
[ 2840.387383]        bus_for_each_drv+0x78/0xc0
[ 2840.387390]        __device_attach+0xb0/0x1b0
[ 2840.387395]        bus_probe_device+0x94/0xb0
[ 2840.387400]        device_add+0x64a/0x860
[ 2840.387405]        usb_set_configuration+0x5e8/0x880
[ 2840.387411]        usb_generic_driver_probe+0x3e/0x60
[ 2840.387418]        usb_probe_device+0x3d/0x120
[ 2840.387423]        really_probe+0xde/0x340
[ 2840.387428]        __driver_probe_device+0x78/0x110
[ 2840.387434]        driver_probe_device+0x1f/0xa0
[ 2840.387439]        __device_attach_driver+0x85/0x110
[ 2840.387444]        bus_for_each_drv+0x78/0xc0
[ 2840.387451]        __device_attach+0xb0/0x1b0
[ 2840.387456]        bus_probe_device+0x94/0xb0
[ 2840.387461]        device_add+0x64a/0x860
[ 2840.387466]        usb_new_device.cold+0x141/0x38f
[ 2840.387473]        hub_event+0x1166/0x1980
[ 2840.387479]        process_one_work+0x21a/0x590
[ 2840.387484]        worker_thread+0x1d1/0x3e0
[ 2840.387488]        kthread+0xee/0x120
[ 2840.387493]        ret_from_fork+0x30/0x50
[ 2840.387500]        ret_from_fork_asm+0x1a/0x30
[ 2840.387506]
               other info that might help us debug this:
[ 2840.387509] Chain exists of:
                 &led_cdev->led_access --> &led_cdev->trigger_lock --> input_mutex
[ 2840.387520]  Possible unsafe locking scenario:
[ 2840.387523]        CPU0                    CPU1
[ 2840.387526]        ----                    ----
[ 2840.387529]   lock(input_mutex);
[ 2840.387534]                                lock(&led_cdev->trigger_lock);
[ 2840.387540]                                lock(input_mutex);
[ 2840.387545]   lock(&led_cdev->led_access);
[ 2840.387550]
                *** DEADLOCK ***
[ 2840.387552] 7 locks held by kworker/1:1/52:
[ 2840.387557]  #0: ffff98fcc1d07148 ((wq_completion)usb_hub_wq){+.+.}-{0:0}, at: process_one_work+0x4af/0x590
[ 2840.387570]  #1: ffffb67e00213e60 ((work_completion)(&hub->events)){+.+.}-{0:0}, at: process_one_work+0x1d5/0x590
[ 2840.387583]  #2: ffff98fcc6582190 (&dev->mutex){....}-{3:3}, at: hub_event+0x57/0x1980
[ 2840.387596]  #3: ffff98fccb3c6990 (&dev->mutex){....}-{3:3}, at: __device_attach+0x26/0x1b0
[ 2840.387610]  #4: ffff98fcc5260960 (&dev->mutex){....}-{3:3}, at: __device_attach+0x26/0x1b0
[ 2840.387622]  #5: ffff98fce3999a20 (&dev->mutex){....}-{3:3}, at: __device_attach+0x26/0x1b0
[ 2840.387635]  #6: ffffffff88130cc8 (input_mutex){+.+.}-{3:3}, at: input_register_device.cold+0x47/0x150
[ 2840.387649]
               stack backtrace:
[ 2840.387653] CPU: 1 PID: 52 Comm: kworker/1:1 Tainted: G         C  E      6.10.0-rc1+ #97
[ 2840.387659] Hardware name: Xiaomi Inc Mipad2/Mipad, BIOS MIPad-P4.X64.0043.R03.1603071414 03/07/2016
[ 2840.387665] Workqueue: usb_hub_wq hub_event
[ 2840.387674] Call Trace:
[ 2840.387681]  <TASK>
[ 2840.387689]  dump_stack_lvl+0x68/0x90
[ 2840.387700]  check_noncircular+0x10d/0x120
[ 2840.387710]  ? register_lock_class+0x38/0x480
[ 2840.387717]  ? check_noncircular+0x74/0x120
[ 2840.387727]  __lock_acquire+0x11c6/0x1f20
[ 2840.387736]  lock_acquire+0xc8/0x2b0
[ 2840.387743]  ? led_classdev_register_ext+0x1c6/0x380
[ 2840.387753]  __mutex_lock+0x8c/0xc10
[ 2840.387760]  ? led_classdev_register_ext+0x1c6/0x380
[ 2840.387766]  ? _raw_spin_unlock_irqrestore+0x35/0x60
[ 2840.387773]  ? klist_next+0x158/0x160
[ 2840.387781]  ? led_classdev_register_ext+0x1c6/0x380
[ 2840.387787]  ? lockdep_init_map_type+0x58/0x250
[ 2840.387796]  ? led_classdev_register_ext+0x1c6/0x380
[ 2840.387802]  led_classdev_register_ext+0x1c6/0x380
[ 2840.387810]  ? kvasprintf+0x70/0xb0
[ 2840.387820]  ? kasprintf+0x3e/0x50
[ 2840.387829]  input_leds_connect+0x139/0x260
[ 2840.387838]  input_attach_handler.isra.0+0x75/0x90
[ 2840.387846]  input_register_device.cold+0xa1/0x150
[ 2840.387854]  hidinput_connect+0x848/0xb00
[ 2840.387862]  ? usbhid_start+0x45b/0x7b0
[ 2840.387870]  hid_connect+0x567/0x5a0
[ 2840.387878]  ? __mutex_unlock_slowpath+0x2d/0x260
[ 2840.387891]  hid_hw_start+0x3f/0x60
[ 2840.387899]  hid_device_probe+0x10d/0x190
[ 2840.387906]  ? __pfx___device_attach_driver+0x10/0x10
[ 2840.387913]  really_probe+0xde/0x340
[ 2840.387919]  ? pm_runtime_barrier+0x50/0x90
[ 2840.387927]  __driver_probe_device+0x78/0x110
[ 2840.387934]  driver_probe_device+0x1f/0xa0
[ 2840.387941]  __device_attach_driver+0x85/0x110
[ 2840.387949]  bus_for_each_drv+0x78/0xc0
[ 2840.387959]  __device_attach+0xb0/0x1b0
[ 2840.387967]  bus_probe_device+0x94/0xb0
[ 2840.387974]  device_add+0x64a/0x860
[ 2840.387982]  ? __debugfs_create_file+0x14a/0x1c0
[ 2840.387993]  hid_add_device+0xe5/0x240
[ 2840.388002]  usbhid_probe+0x4bb/0x600
[ 2840.388013]  usb_probe_interface+0xea/0x2b0
[ 2840.388021]  ? __pfx___device_attach_driver+0x10/0x10
[ 2840.388028]  really_probe+0xde/0x340
[ 2840.388034]  ? pm_runtime_barrier+0x50/0x90
[ 2840.388040]  __driver_probe_device+0x78/0x110
[ 2840.388048]  driver_probe_device+0x1f/0xa0
[ 2840.388055]  __device_attach_driver+0x85/0x110
[ 2840.388062]  bus_for_each_drv+0x78/0xc0
[ 2840.388071]  __device_attach+0xb0/0x1b0
[ 2840.388079]  bus_probe_device+0x94/0xb0
[ 2840.388086]  device_add+0x64a/0x860
[ 2840.388094]  ? __mutex_unlock_slowpath+0x2d/0x260
[ 2840.388103]  usb_set_configuration+0x5e8/0x880
[ 2840.388114]  ? __pfx___device_attach_driver+0x10/0x10
[ 2840.388121]  usb_generic_driver_probe+0x3e/0x60
[ 2840.388129]  usb_probe_device+0x3d/0x120
[ 2840.388137]  really_probe+0xde/0x340
[ 2840.388142]  ? pm_runtime_barrier+0x50/0x90
[ 2840.388149]  __driver_probe_device+0x78/0x110
[ 2840.388156]  driver_probe_device+0x1f/0xa0
[ 2840.388163]  __device_attach_driver+0x85/0x110
[ 2840.388171]  bus_for_each_drv+0x78/0xc0
[ 2840.388180]  __device_attach+0xb0/0x1b0
[ 2840.388188]  bus_probe_device+0x94/0xb0
[ 2840.388195]  device_add+0x64a/0x860
[ 2840.388202]  ? lockdep_hardirqs_on+0x78/0x100
[ 2840.388210]  ? _raw_spin_unlock_irqrestore+0x35/0x60
[ 2840.388219]  usb_new_device.cold+0x141/0x38f
[ 2840.388227]  hub_event+0x1166/0x1980
[ 2840.388242]  process_one_work+0x21a/0x590
[ 2840.388249]  ? move_linked_works+0x70/0xa0
[ 2840.388260]  worker_thread+0x1d1/0x3e0
Quoted 8 lines
[ 2840.388268]  ? __pfx_worker_thread+0x10/0x10
[ 2840.388273]  kthread+0xee/0x120
[ 2840.388279]  ? __pfx_kthread+0x10/0x10
[ 2840.388287]  ret_from_fork+0x30/0x50
[ 2840.388294]  ? __pfx_kthread+0x10/0x10
[ 2840.388301]  ret_from_fork_asm+0x1a/0x30
[ 2840.388315]  </TASK>
[ 2840.415630] hid-generic 0003:0603:0002.0007: input,hidraw6: USB HID v1.10 Keyboard [SINO WEALTH USB Composite Device] on usb-0000:00:14.0-1.3/input0

Do we really have to add the _whole_ trace?

Is there no way to snip it a little?

Or perhaps Link: to the whole trace?

Quoted 4 lines
---
 drivers/leds/trigger/ledtrig-input-events.c | 136 +++++---------------
 1 file changed, 34 insertions(+), 102 deletions(-)

This is nice!

Quoted 30 lines
drivers/leds/trigger/ledtrig-input-events.c +6 -4
index 1de0176799f9..1c79731562c2 100644
@@ -3,31 +3,32 @@
  * Input Events LED trigger
  *
  * Copyright (C) 2024 Hans de Goede <[email protected]>
- * Partially based on Atsushi Nemoto's ledtrig-heartbeat.c.
  */
 
 #include <linux/input.h>
 #include <linux/jiffies.h>
 #include <linux/leds.h>
 #include <linux/module.h>
+#include <linux/moduleparam.h>
 #include <linux/slab.h>
 #include <linux/spinlock.h>
 #include <linux/workqueue.h>
 #include "../leds.h"
 
-#define DEFAULT_LED_OFF_DELAY_MS			5000
+static unsigned long led_off_delay_ms = 5000;
+module_param(led_off_delay_ms, ulong, 0644);
+MODULE_PARM_DESC(led_off_delay_ms,
+	"Specify delay in ms for turning LEDs off after last input event");
 
-struct input_events_data {
-	struct input_handler handler;
+static struct input_events_data {

drivers/leds/trigger/ledtrig-input-events.c line 29

Quoted 10 lines
drivers/leds/trigger/ledtrig-input-events.c +1 -4
 	struct delayed_work work;
 	spinlock_t lock;
-	struct led_classdev *led_cdev;
-	int led_cdev_saved_flags;
 	/* To avoid repeatedly setting the brightness while there are events */
 	bool led_on;
 	unsigned long led_off_time;
-	unsigned long led_off_delay;
-};
+} input_events_data;

Does this fix really require statically declared structs?

Quoted 47 lines
drivers/leds/trigger/ledtrig-input-events.c +2 -32
+static struct led_trigger *input_events_led_trigger;
 
 static void led_input_events_work(struct work_struct *work)
 {
@@ -41,62 +42,24 @@ static void led_input_events_work(struct work_struct *work)
 	 * running before a new event pushed led_off_time back.
 	 */
 	if (time_after_eq(jiffies, data->led_off_time)) {
-		led_set_brightness_nosleep(data->led_cdev, LED_OFF);
+		led_trigger_event(input_events_led_trigger, LED_OFF);
 		data->led_on = false;
 	}
 
 	spin_unlock_irq(&data->lock);
 }
 
-static ssize_t delay_show(struct device *dev, struct device_attribute *attr, char *buf)
-{
-	struct input_events_data *input_events_data = led_trigger_get_drvdata(dev);
-
-	return sysfs_emit(buf, "%lu\n", input_events_data->led_off_delay);
-}
-
-static ssize_t delay_store(struct device *dev, struct device_attribute *attr,
-			   const char *buf, size_t size)
-{
-	struct input_events_data *input_events_data = led_trigger_get_drvdata(dev);
-	unsigned long delay;
-	int ret;
-
-	ret = kstrtoul(buf, 0, &delay);
-	if (ret)
-		return ret;
-
-	/* Clamp between 0.5 and 1000 seconds */
-	delay = clamp_val(delay, 500UL, 1000000UL);
-	input_events_data->led_off_delay = msecs_to_jiffies(delay);
-
-	return size;
-}
-
-static DEVICE_ATTR_RW(delay);
-
-static struct attribute *input_events_led_attrs[] = {
-	&dev_attr_delay.attr,
-	NULL
-};

drivers/leds/trigger/ledtrig-input-events.c static void led_input_events_work(struct work_struct *work) · line 55

Quoted 10 lines
drivers/leds/trigger/ledtrig-input-events.c +1 -6
-ATTRIBUTE_GROUPS(input_events_led);
-
 static void input_events_event(struct input_handle *handle, unsigned int type,
 			       unsigned int code, int val)
 {
-	struct input_events_data *data =
-		container_of(handle->handler, struct input_events_data, handler);
-	unsigned long led_off_delay = READ_ONCE(data->led_off_delay);
-	struct led_classdev *led_cdev = data->led_cdev;
+	struct input_events_data *data = &input_events_data;

IFF we have to use statically declared structs ...

Why not just use input_events_data.foo?

Quoted 120 lines
drivers/leds/trigger/ledtrig-input-events.c +23 -56
+	unsigned long led_off_delay = msecs_to_jiffies(led_off_delay_ms);
 	unsigned long flags;
 
-	if (test_and_clear_bit(LED_BLINK_BRIGHTNESS_CHANGE, &led_cdev->work_flags))
-		led_cdev->blink_brightness = led_cdev->new_blink_brightness;
-
 	spin_lock_irqsave(&data->lock, flags);
 
 	if (!data->led_on) {
-		led_set_brightness_nosleep(led_cdev, led_cdev->blink_brightness);
+		led_trigger_event(input_events_led_trigger, LED_FULL);
 		data->led_on = true;
 	}
 	data->led_off_time = jiffies + led_off_delay;
@@ -118,7 +81,7 @@ static int input_events_connect(struct input_handler *handler, struct input_dev
 
 	handle->dev = dev;
 	handle->handler = handler;
-	handle->name = "input-events";
+	handle->name = KBUILD_MODNAME;
 
 	ret = input_register_handle(handle);
 	if (ret)
@@ -160,72 +123,41 @@ static const struct input_device_id input_events_ids[] = {
 	{ }
 };
 
-static int input_events_activate(struct led_classdev *led_cdev)
+static struct input_handler input_events_handler = {
+	.name = KBUILD_MODNAME,
+	.event = input_events_event,
+	.connect = input_events_connect,
+	.disconnect = input_events_disconnect,
+	.id_table = input_events_ids,
+};
+
+static int __init input_events_init(void)
 {
-	struct input_events_data *data;
 	int ret;
 
-	data = kzalloc(sizeof(*data), GFP_KERNEL);
-	if (!data)
-		return -ENOMEM;
+	INIT_DELAYED_WORK(&input_events_data.work, led_input_events_work);
+	spin_lock_init(&input_events_data.lock);
 
-	data->handler.name = "input-events";
-	data->handler.event = input_events_event;
-	data->handler.connect = input_events_connect;
-	data->handler.disconnect = input_events_disconnect;
-	data->handler.id_table = input_events_ids;
+	led_trigger_register_simple("input-events", &input_events_led_trigger);
 
-	INIT_DELAYED_WORK(&data->work, led_input_events_work);
-	spin_lock_init(&data->lock);
-
-	data->led_cdev = led_cdev;
-	data->led_cdev_saved_flags = led_cdev->flags;
-	data->led_off_delay = msecs_to_jiffies(DEFAULT_LED_OFF_DELAY_MS);
-
-	/*
-	 * Use led_cdev->blink_brightness + LED_BLINK_SW flag so that sysfs
-	 * brightness writes will change led_cdev->new_blink_brightness for
-	 * configuring the on state brightness (like ledtrig-heartbeat).
-	 */
-	if (!led_cdev->blink_brightness)
-		led_cdev->blink_brightness = led_cdev->max_brightness;
-
-	/* Start with LED off */
-	led_set_brightness_nosleep(data->led_cdev, LED_OFF);
-
-	ret = input_register_handler(&data->handler);
+	ret = input_register_handler(&input_events_handler);
 	if (ret) {
-		kfree(data);
+		led_trigger_unregister_simple(input_events_led_trigger);
 		return ret;
 	}
 
-	set_bit(LED_BLINK_SW, &led_cdev->work_flags);
-
-	/* Turn LED off during suspend, original flags are restored on deactivate() */
-	led_cdev->flags |= LED_CORE_SUSPENDRESUME;
-
-	led_set_trigger_data(led_cdev, data);
 	return 0;
 }
 
-static void input_events_deactivate(struct led_classdev *led_cdev)
+static void __exit input_events_exit(void)
 {
-	struct input_events_data *data = led_get_trigger_data(led_cdev);
-
-	led_cdev->flags = data->led_cdev_saved_flags;
-	clear_bit(LED_BLINK_SW, &led_cdev->work_flags);
-	input_unregister_handler(&data->handler);
-	cancel_delayed_work_sync(&data->work);
-	kfree(data);
+	input_unregister_handler(&input_events_handler);
+	cancel_delayed_work_sync(&input_events_data.work);
+	led_trigger_unregister_simple(input_events_led_trigger);
 }
 
-static struct led_trigger input_events_led_trigger = {
-	.name       = "input-events",
-	.activate   = input_events_activate,
-	.deactivate = input_events_deactivate,
-	.groups     = input_events_led_groups,
-};
-module_led_trigger(input_events_led_trigger);
+module_init(input_events_init);
+module_exit(input_events_exit);
 
 MODULE_AUTHOR("Hans de Goede <[email protected]>");
 MODULE_DESCRIPTION("Input Events LED trigger");
Signature · 1 line
2.45.1
Signature · 1 line
Lee Jones [李琼斯]
#3 lore raw

Hi Lee,

Quoted 259 lines · Lee Jones
Quoted 248 lines · Hans de Goede

The input subsystem registers LEDs with default triggers while holding the input_lock and input_register_handler() takes the input_lock this means that a triggers activate method cannot directly call input_register_handler() as the old ledtrig-input-events code is doing.

The initial implementation of the input-events trigger mainly did not use the simple LED trigger mechanism because that mechanism had an issue with the initial state of a newly activated LED not matching the last led_trigger_event() call for the trigger. This issue has been fixed in commit 822c91e72eac ("leds: trigger: Store brightness set by led_trigger_event()").

Rewrite the "input-events" trigger to use the simple LED trigger mechanism, registering a single input_handler at module_init() time and using led_trigger_event() to set the brightness for all LEDs controlled by this trigger.

Compared to the old code this looses the ability for the user to configure a different brightness for the on state then LED_FULL, this is standard for simple LED triggers and since this trigger is only in for-leds-next ATM losing that functionality is not a regression.

This also changes the configurability of the LED off timeout from a per LED setting to a global setting (runtime modifiable module-parameter).

Switching to registering a single input_handler at module_init() time fixes the following locking issue reported by lockdep:

[ 2840.220145] usb 1-1.3: new low-speed USB device number 3 using xhci_hcd
[ 2840.307172] usb 1-1.3: New USB device found, idVendor=0603, idProduct=0002, bcdDevice= 2.21
[ 2840.307375] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2840.307423] usb 1-1.3: Product: USB Composite Device
[ 2840.307456] usb 1-1.3: Manufacturer: SINO WEALTH
[ 2840.333985] input: SINO WEALTH USB Composite Device as /devices/pci0000:00/0000:00:14.0/usb1/1-1/1-1.3/1-1.3:1.0/0003:0603:0002.0007/input/input19
[ 2840.386545] ======================================================
[ 2840.386549] WARNING: possible circular locking dependency detected
[ 2840.386554] 6.10.0-rc1+ #97 Tainted: G         C  E
[ 2840.386558] ------------------------------------------------------
[ 2840.386562] kworker/1:1/52 is trying to acquire lock:
[ 2840.386566] ffff98fcf1629300 (&led_cdev->led_access){+.+.}-{3:3}, at: led_classdev_register_ext+0x1c6/0x380
[ 2840.386590]
               but task is already holding lock:
[ 2840.386593] ffffffff88130cc8 (input_mutex){+.+.}-{3:3}, at: input_register_device.cold+0x47/0x150
[ 2840.386608]
               which lock already depends on the new lock.
[ 2840.386611]
               the existing dependency chain (in reverse order) is:
[ 2840.386615]
               -> #3 (input_mutex){+.+.}-{3:3}:
[ 2840.386624]        __mutex_lock+0x8c/0xc10
[ 2840.386634]        input_register_handler+0x1c/0xf0
[ 2840.386641]        0xffffffffc142c437
[ 2840.386655]        led_trigger_set+0x1e1/0x2e0
[ 2840.386661]        led_trigger_register+0x170/0x1b0
[ 2840.386666]        do_one_initcall+0x5e/0x3a0
[ 2840.386675]        do_init_module+0x60/0x220
[ 2840.386683]        __do_sys_init_module+0x15f/0x190
[ 2840.386689]        do_syscall_64+0x93/0x180
[ 2840.386696]        entry_SYSCALL_64_after_hwframe+0x76/0x7e
[ 2840.386705]
               -> #2 (&led_cdev->trigger_lock){+.+.}-{3:3}:
[ 2840.386714]        down_write+0x3b/0xd0
[ 2840.386720]        led_trigger_register+0x12c/0x1b0
[ 2840.386725]        rfkill_register+0xec/0x340 [rfkill]
[ 2840.386739]        wiphy_register+0x82a/0x930 [cfg80211]
[ 2840.386907]        brcmf_cfg80211_attach+0xcbd/0x1430 [brcmfmac]
[ 2840.386952]        brcmf_attach+0x1ba/0x4c0 [brcmfmac]
[ 2840.386991]        brcmf_pcie_setup+0x899/0xc70 [brcmfmac]
[ 2840.387030]        brcmf_fw_request_done+0x13b/0x180 [brcmfmac]
[ 2840.387070]        request_firmware_work_func+0x3b/0x70
[ 2840.387078]        process_one_work+0x21a/0x590
[ 2840.387085]        worker_thread+0x1d1/0x3e0
[ 2840.387090]        kthread+0xee/0x120
[ 2840.387096]        ret_from_fork+0x30/0x50
[ 2840.387105]        ret_from_fork_asm+0x1a/0x30
[ 2840.387112]
               -> #1 (leds_list_lock){++++}-{3:3}:
[ 2840.387123]        down_write+0x3b/0xd0
[ 2840.387129]        led_classdev_register_ext+0x29e/0x380
[ 2840.387134]        0xffffffffc0e6b74c
[ 2840.387143]        platform_probe+0x40/0xa0
[ 2840.387151]        really_probe+0xde/0x340
[ 2840.387157]        __driver_probe_device+0x78/0x110
[ 2840.387162]        driver_probe_device+0x1f/0xa0
[ 2840.387168]        __driver_attach+0xba/0x1c0
[ 2840.387173]        bus_for_each_dev+0x6b/0xb0
[ 2840.387180]        bus_add_driver+0x111/0x1f0
[ 2840.387185]        driver_register+0x6e/0xc0
[ 2840.387191]        do_one_initcall+0x5e/0x3a0
[ 2840.387197]        do_init_module+0x60/0x220
[ 2840.387204]        __do_sys_init_module+0x15f/0x190
[ 2840.387210]        do_syscall_64+0x93/0x180
[ 2840.387217]        entry_SYSCALL_64_after_hwframe+0x76/0x7e
[ 2840.387224]
               -> #0 (&led_cdev->led_access){+.+.}-{3:3}:
[ 2840.387233]        __lock_acquire+0x11c6/0x1f20
[ 2840.387239]        lock_acquire+0xc8/0x2b0
[ 2840.387244]        __mutex_lock+0x8c/0xc10
[ 2840.387251]        led_classdev_register_ext+0x1c6/0x380
[ 2840.387256]        input_leds_connect+0x139/0x260
[ 2840.387262]        input_attach_handler.isra.0+0x75/0x90
[ 2840.387268]        input_register_device.cold+0xa1/0x150
[ 2840.387274]        hidinput_connect+0x848/0xb00
[ 2840.387280]        hid_connect+0x567/0x5a0
[ 2840.387288]        hid_hw_start+0x3f/0x60
[ 2840.387294]        hid_device_probe+0x10d/0x190
[ 2840.387298]        really_probe+0xde/0x340
[ 2840.387304]        __driver_probe_device+0x78/0x110
[ 2840.387309]        driver_probe_device+0x1f/0xa0
[ 2840.387314]        __device_attach_driver+0x85/0x110
[ 2840.387320]        bus_for_each_drv+0x78/0xc0
[ 2840.387326]        __device_attach+0xb0/0x1b0
[ 2840.387332]        bus_probe_device+0x94/0xb0
[ 2840.387337]        device_add+0x64a/0x860
[ 2840.387343]        hid_add_device+0xe5/0x240
[ 2840.387349]        usbhid_probe+0x4bb/0x600
[ 2840.387356]        usb_probe_interface+0xea/0x2b0
[ 2840.387363]        really_probe+0xde/0x340
[ 2840.387368]        __driver_probe_device+0x78/0x110
[ 2840.387373]        driver_probe_device+0x1f/0xa0
[ 2840.387378]        __device_attach_driver+0x85/0x110
[ 2840.387383]        bus_for_each_drv+0x78/0xc0
[ 2840.387390]        __device_attach+0xb0/0x1b0
[ 2840.387395]        bus_probe_device+0x94/0xb0
[ 2840.387400]        device_add+0x64a/0x860
[ 2840.387405]        usb_set_configuration+0x5e8/0x880
[ 2840.387411]        usb_generic_driver_probe+0x3e/0x60
[ 2840.387418]        usb_probe_device+0x3d/0x120
[ 2840.387423]        really_probe+0xde/0x340
[ 2840.387428]        __driver_probe_device+0x78/0x110
[ 2840.387434]        driver_probe_device+0x1f/0xa0
[ 2840.387439]        __device_attach_driver+0x85/0x110
[ 2840.387444]        bus_for_each_drv+0x78/0xc0
[ 2840.387451]        __device_attach+0xb0/0x1b0
[ 2840.387456]        bus_probe_device+0x94/0xb0
[ 2840.387461]        device_add+0x64a/0x860
[ 2840.387466]        usb_new_device.cold+0x141/0x38f
[ 2840.387473]        hub_event+0x1166/0x1980
[ 2840.387479]        process_one_work+0x21a/0x590
[ 2840.387484]        worker_thread+0x1d1/0x3e0
[ 2840.387488]        kthread+0xee/0x120
[ 2840.387493]        ret_from_fork+0x30/0x50
[ 2840.387500]        ret_from_fork_asm+0x1a/0x30
[ 2840.387506]
               other info that might help us debug this:
[ 2840.387509] Chain exists of:
                 &led_cdev->led_access --> &led_cdev->trigger_lock --> input_mutex
[ 2840.387520]  Possible unsafe locking scenario:
[ 2840.387523]        CPU0                    CPU1
[ 2840.387526]        ----                    ----
[ 2840.387529]   lock(input_mutex);
[ 2840.387534]                                lock(&led_cdev->trigger_lock);
[ 2840.387540]                                lock(input_mutex);
[ 2840.387545]   lock(&led_cdev->led_access);
[ 2840.387550]
                *** DEADLOCK ***
[ 2840.387552] 7 locks held by kworker/1:1/52:
[ 2840.387557]  #0: ffff98fcc1d07148 ((wq_completion)usb_hub_wq){+.+.}-{0:0}, at: process_one_work+0x4af/0x590
[ 2840.387570]  #1: ffffb67e00213e60 ((work_completion)(&hub->events)){+.+.}-{0:0}, at: process_one_work+0x1d5/0x590
[ 2840.387583]  #2: ffff98fcc6582190 (&dev->mutex){....}-{3:3}, at: hub_event+0x57/0x1980
[ 2840.387596]  #3: ffff98fccb3c6990 (&dev->mutex){....}-{3:3}, at: __device_attach+0x26/0x1b0
[ 2840.387610]  #4: ffff98fcc5260960 (&dev->mutex){....}-{3:3}, at: __device_attach+0x26/0x1b0
[ 2840.387622]  #5: ffff98fce3999a20 (&dev->mutex){....}-{3:3}, at: __device_attach+0x26/0x1b0
[ 2840.387635]  #6: ffffffff88130cc8 (input_mutex){+.+.}-{3:3}, at: input_register_device.cold+0x47/0x150
[ 2840.387649]
               stack backtrace:
[ 2840.387653] CPU: 1 PID: 52 Comm: kworker/1:1 Tainted: G         C  E      6.10.0-rc1+ #97
[ 2840.387659] Hardware name: Xiaomi Inc Mipad2/Mipad, BIOS MIPad-P4.X64.0043.R03.1603071414 03/07/2016
[ 2840.387665] Workqueue: usb_hub_wq hub_event
[ 2840.387674] Call Trace:
[ 2840.387681]  <TASK>
[ 2840.387689]  dump_stack_lvl+0x68/0x90
[ 2840.387700]  check_noncircular+0x10d/0x120
[ 2840.387710]  ? register_lock_class+0x38/0x480
[ 2840.387717]  ? check_noncircular+0x74/0x120
[ 2840.387727]  __lock_acquire+0x11c6/0x1f20
[ 2840.387736]  lock_acquire+0xc8/0x2b0
[ 2840.387743]  ? led_classdev_register_ext+0x1c6/0x380
[ 2840.387753]  __mutex_lock+0x8c/0xc10
[ 2840.387760]  ? led_classdev_register_ext+0x1c6/0x380
[ 2840.387766]  ? _raw_spin_unlock_irqrestore+0x35/0x60
[ 2840.387773]  ? klist_next+0x158/0x160
[ 2840.387781]  ? led_classdev_register_ext+0x1c6/0x380
[ 2840.387787]  ? lockdep_init_map_type+0x58/0x250
[ 2840.387796]  ? led_classdev_register_ext+0x1c6/0x380
[ 2840.387802]  led_classdev_register_ext+0x1c6/0x380
[ 2840.387810]  ? kvasprintf+0x70/0xb0
[ 2840.387820]  ? kasprintf+0x3e/0x50
[ 2840.387829]  input_leds_connect+0x139/0x260
[ 2840.387838]  input_attach_handler.isra.0+0x75/0x90
[ 2840.387846]  input_register_device.cold+0xa1/0x150
[ 2840.387854]  hidinput_connect+0x848/0xb00
[ 2840.387862]  ? usbhid_start+0x45b/0x7b0
[ 2840.387870]  hid_connect+0x567/0x5a0
[ 2840.387878]  ? __mutex_unlock_slowpath+0x2d/0x260
[ 2840.387891]  hid_hw_start+0x3f/0x60
[ 2840.387899]  hid_device_probe+0x10d/0x190
[ 2840.387906]  ? __pfx___device_attach_driver+0x10/0x10
[ 2840.387913]  really_probe+0xde/0x340
[ 2840.387919]  ? pm_runtime_barrier+0x50/0x90
[ 2840.387927]  __driver_probe_device+0x78/0x110
[ 2840.387934]  driver_probe_device+0x1f/0xa0
[ 2840.387941]  __device_attach_driver+0x85/0x110
[ 2840.387949]  bus_for_each_drv+0x78/0xc0
[ 2840.387959]  __device_attach+0xb0/0x1b0
[ 2840.387967]  bus_probe_device+0x94/0xb0
[ 2840.387974]  device_add+0x64a/0x860
[ 2840.387982]  ? __debugfs_create_file+0x14a/0x1c0
[ 2840.387993]  hid_add_device+0xe5/0x240
[ 2840.388002]  usbhid_probe+0x4bb/0x600
[ 2840.388013]  usb_probe_interface+0xea/0x2b0
[ 2840.388021]  ? __pfx___device_attach_driver+0x10/0x10
[ 2840.388028]  really_probe+0xde/0x340
[ 2840.388034]  ? pm_runtime_barrier+0x50/0x90
[ 2840.388040]  __driver_probe_device+0x78/0x110
[ 2840.388048]  driver_probe_device+0x1f/0xa0
[ 2840.388055]  __device_attach_driver+0x85/0x110
[ 2840.388062]  bus_for_each_drv+0x78/0xc0
[ 2840.388071]  __device_attach+0xb0/0x1b0
[ 2840.388079]  bus_probe_device+0x94/0xb0
[ 2840.388086]  device_add+0x64a/0x860
[ 2840.388094]  ? __mutex_unlock_slowpath+0x2d/0x260
[ 2840.388103]  usb_set_configuration+0x5e8/0x880
[ 2840.388114]  ? __pfx___device_attach_driver+0x10/0x10
[ 2840.388121]  usb_generic_driver_probe+0x3e/0x60
[ 2840.388129]  usb_probe_device+0x3d/0x120
[ 2840.388137]  really_probe+0xde/0x340
[ 2840.388142]  ? pm_runtime_barrier+0x50/0x90
[ 2840.388149]  __driver_probe_device+0x78/0x110
[ 2840.388156]  driver_probe_device+0x1f/0xa0
[ 2840.388163]  __device_attach_driver+0x85/0x110
[ 2840.388171]  bus_for_each_drv+0x78/0xc0
[ 2840.388180]  __device_attach+0xb0/0x1b0
[ 2840.388188]  bus_probe_device+0x94/0xb0
[ 2840.388195]  device_add+0x64a/0x860
[ 2840.388202]  ? lockdep_hardirqs_on+0x78/0x100
[ 2840.388210]  ? _raw_spin_unlock_irqrestore+0x35/0x60
[ 2840.388219]  usb_new_device.cold+0x141/0x38f
[ 2840.388227]  hub_event+0x1166/0x1980
[ 2840.388242]  process_one_work+0x21a/0x590
[ 2840.388249]  ? move_linked_works+0x70/0xa0
[ 2840.388260]  worker_thread+0x1d1/0x3e0
Quoted 8 lines
[ 2840.388268]  ? __pfx_worker_thread+0x10/0x10
[ 2840.388273]  kthread+0xee/0x120
[ 2840.388279]  ? __pfx_kthread+0x10/0x10
[ 2840.388287]  ret_from_fork+0x30/0x50
[ 2840.388294]  ? __pfx_kthread+0x10/0x10
[ 2840.388301]  ret_from_fork_asm+0x1a/0x30
[ 2840.388315]  </TASK>
[ 2840.415630] hid-generic 0003:0603:0002.0007: input,hidraw6: USB HID v1.10 Keyboard [SINO WEALTH USB Composite Device] on usb-0000:00:14.0-1.3/input0
Quoted 3 lines

Do we really have to add the _whole_ trace?

Is there no way to snip it a little?

It should be possible to shorten it somewhat for v2.

Quoted 36 lines

Or perhaps Link: to the whole trace?

Quoted 4 lines
---
 drivers/leds/trigger/ledtrig-input-events.c | 136 +++++---------------
 1 file changed, 34 insertions(+), 102 deletions(-)

This is nice!

Quoted 27 lines
drivers/leds/trigger/ledtrig-input-events.c +5 -2
index 1de0176799f9..1c79731562c2 100644
@@ -3,31 +3,32 @@
  * Input Events LED trigger
  *
  * Copyright (C) 2024 Hans de Goede <[email protected]>
- * Partially based on Atsushi Nemoto's ledtrig-heartbeat.c.
  */
 
 #include <linux/input.h>
 #include <linux/jiffies.h>
 #include <linux/leds.h>
 #include <linux/module.h>
+#include <linux/moduleparam.h>
 #include <linux/slab.h>
 #include <linux/spinlock.h>
 #include <linux/workqueue.h>
 #include "../leds.h"
 
-#define DEFAULT_LED_OFF_DELAY_MS			5000
+static unsigned long led_off_delay_ms = 5000;
+module_param(led_off_delay_ms, ulong, 0644);
+MODULE_PARM_DESC(led_off_delay_ms,
+	"Specify delay in ms for turning LEDs off after last input event");
 
Quoted 15 lines

drivers/leds/trigger/ledtrig-input-events.c line 29

Quoted 13 lines
drivers/leds/trigger/ledtrig-input-events.c +2 -6
-struct input_events_data {
-	struct input_handler handler;
+static struct input_events_data {
 	struct delayed_work work;
 	spinlock_t lock;
-	struct led_classdev *led_cdev;
-	int led_cdev_saved_flags;
 	/* To avoid repeatedly setting the brightness while there are events */
 	bool led_on;
 	unsigned long led_off_time;
-	unsigned long led_off_delay;
-};
+} input_events_data;

Does this fix really require statically declared structs?

With the move the the simple LED trigger model there is a single global state for all LEDs controlled by this trigger rather then per LED state.

So we need to have global static data for this. To keep the diff compared to the previous version small; and because I personally find doing so somewhat cleaner; I have chosen to keep this global state in a struct rather then using multiple global variables for this.

If you strongly prefer using multiple global variables for this then that can be changed for v2.

Quoted 61 lines
Quoted 48 lines
drivers/leds/trigger/ledtrig-input-events.c +2 -32
+static struct led_trigger *input_events_led_trigger;
 
 static void led_input_events_work(struct work_struct *work)
 {
@@ -41,62 +42,24 @@ static void led_input_events_work(struct work_struct *work)
 	 * running before a new event pushed led_off_time back.
 	 */
 	if (time_after_eq(jiffies, data->led_off_time)) {
-		led_set_brightness_nosleep(data->led_cdev, LED_OFF);
+		led_trigger_event(input_events_led_trigger, LED_OFF);
 		data->led_on = false;
 	}
 
 	spin_unlock_irq(&data->lock);
 }
 
-static ssize_t delay_show(struct device *dev, struct device_attribute *attr, char *buf)
-{
-	struct input_events_data *input_events_data = led_trigger_get_drvdata(dev);
-
-	return sysfs_emit(buf, "%lu\n", input_events_data->led_off_delay);
-}
-
-static ssize_t delay_store(struct device *dev, struct device_attribute *attr,
-			   const char *buf, size_t size)
-{
-	struct input_events_data *input_events_data = led_trigger_get_drvdata(dev);
-	unsigned long delay;
-	int ret;
-
-	ret = kstrtoul(buf, 0, &delay);
-	if (ret)
-		return ret;
-
-	/* Clamp between 0.5 and 1000 seconds */
-	delay = clamp_val(delay, 500UL, 1000000UL);
-	input_events_data->led_off_delay = msecs_to_jiffies(delay);
-
-	return size;
-}
-
-static DEVICE_ATTR_RW(delay);
-
-static struct attribute *input_events_led_attrs[] = {
-	&dev_attr_delay.attr,
-	NULL
-};

drivers/leds/trigger/ledtrig-input-events.c static void led_input_events_work(struct work_struct *work) · line 55

Quoted 10 lines
drivers/leds/trigger/ledtrig-input-events.c +1 -6
-ATTRIBUTE_GROUPS(input_events_led);
-
 static void input_events_event(struct input_handle *handle, unsigned int type,
 			       unsigned int code, int val)
 {
-	struct input_events_data *data =
-		container_of(handle->handler, struct input_events_data, handler);
-	unsigned long led_off_delay = READ_ONCE(data->led_off_delay);
-	struct led_classdev *led_cdev = data->led_cdev;
+	struct input_events_data *data = &input_events_data;

IFF we have to use statically declared structs ...

Quoted 1 line

Why not just use input_events_data.foo?

Yes that will work too. I went this route both for readability (data->foo is easier to read then input_events_data.foo) as well as to keep the diff smaller since some of the old code which this patch keeps around has data->foo.

Note both arguments clearly are invalid if the decision is made to switch to using multiple global variables instead of using a static global struct.

Quoted 115 lines
Quoted 115 lines
drivers/leds/trigger/ledtrig-input-events.c +23 -56
+	unsigned long led_off_delay = msecs_to_jiffies(led_off_delay_ms);
 	unsigned long flags;
 
-	if (test_and_clear_bit(LED_BLINK_BRIGHTNESS_CHANGE, &led_cdev->work_flags))
-		led_cdev->blink_brightness = led_cdev->new_blink_brightness;
-
 	spin_lock_irqsave(&data->lock, flags);
 
 	if (!data->led_on) {
-		led_set_brightness_nosleep(led_cdev, led_cdev->blink_brightness);
+		led_trigger_event(input_events_led_trigger, LED_FULL);
 		data->led_on = true;
 	}
 	data->led_off_time = jiffies + led_off_delay;
@@ -118,7 +81,7 @@ static int input_events_connect(struct input_handler *handler, struct input_dev
 
 	handle->dev = dev;
 	handle->handler = handler;
-	handle->name = "input-events";
+	handle->name = KBUILD_MODNAME;
 
 	ret = input_register_handle(handle);
 	if (ret)
@@ -160,72 +123,41 @@ static const struct input_device_id input_events_ids[] = {
 	{ }
 };
 
-static int input_events_activate(struct led_classdev *led_cdev)
+static struct input_handler input_events_handler = {
+	.name = KBUILD_MODNAME,
+	.event = input_events_event,
+	.connect = input_events_connect,
+	.disconnect = input_events_disconnect,
+	.id_table = input_events_ids,
+};
+
+static int __init input_events_init(void)
 {
-	struct input_events_data *data;
 	int ret;
 
-	data = kzalloc(sizeof(*data), GFP_KERNEL);
-	if (!data)
-		return -ENOMEM;
+	INIT_DELAYED_WORK(&input_events_data.work, led_input_events_work);
+	spin_lock_init(&input_events_data.lock);
 
-	data->handler.name = "input-events";
-	data->handler.event = input_events_event;
-	data->handler.connect = input_events_connect;
-	data->handler.disconnect = input_events_disconnect;
-	data->handler.id_table = input_events_ids;
+	led_trigger_register_simple("input-events", &input_events_led_trigger);
 
-	INIT_DELAYED_WORK(&data->work, led_input_events_work);
-	spin_lock_init(&data->lock);
-
-	data->led_cdev = led_cdev;
-	data->led_cdev_saved_flags = led_cdev->flags;
-	data->led_off_delay = msecs_to_jiffies(DEFAULT_LED_OFF_DELAY_MS);
-
-	/*
-	 * Use led_cdev->blink_brightness + LED_BLINK_SW flag so that sysfs
-	 * brightness writes will change led_cdev->new_blink_brightness for
-	 * configuring the on state brightness (like ledtrig-heartbeat).
-	 */
-	if (!led_cdev->blink_brightness)
-		led_cdev->blink_brightness = led_cdev->max_brightness;
-
-	/* Start with LED off */
-	led_set_brightness_nosleep(data->led_cdev, LED_OFF);
-
-	ret = input_register_handler(&data->handler);
+	ret = input_register_handler(&input_events_handler);
 	if (ret) {
-		kfree(data);
+		led_trigger_unregister_simple(input_events_led_trigger);
 		return ret;
 	}
 
-	set_bit(LED_BLINK_SW, &led_cdev->work_flags);
-
-	/* Turn LED off during suspend, original flags are restored on deactivate() */
-	led_cdev->flags |= LED_CORE_SUSPENDRESUME;
-
-	led_set_trigger_data(led_cdev, data);
 	return 0;
 }
 
-static void input_events_deactivate(struct led_classdev *led_cdev)
+static void __exit input_events_exit(void)
 {
-	struct input_events_data *data = led_get_trigger_data(led_cdev);
-
-	led_cdev->flags = data->led_cdev_saved_flags;
-	clear_bit(LED_BLINK_SW, &led_cdev->work_flags);
-	input_unregister_handler(&data->handler);
-	cancel_delayed_work_sync(&data->work);
-	kfree(data);
+	input_unregister_handler(&input_events_handler);
+	cancel_delayed_work_sync(&input_events_data.work);
+	led_trigger_unregister_simple(input_events_led_trigger);
 }
 
-static struct led_trigger input_events_led_trigger = {
-	.name       = "input-events",
-	.activate   = input_events_activate,
-	.deactivate = input_events_deactivate,
-	.groups     = input_events_led_groups,
-};
-module_led_trigger(input_events_led_trigger);
+module_init(input_events_init);
+module_exit(input_events_exit);
 
Quoted 7 lines
Quoted 6 lines
drivers/leds/trigger/ledtrig-input-events.c +0 -0
 MODULE_AUTHOR("Hans de Goede <[email protected]>");
 MODULE_DESCRIPTION("Input Events LED trigger");
Signature · 1 line
2.45.1

Regards,

Hans

maintainer Applied
#4 lore raw

Re: (subset) [PATCH 1/1] leds: trigger: input-events: Rewrite to fix a serious locking issue

In reply to Hans de Goede
Quoted 5 lines · Hans de Goede

The input subsystem registers LEDs with default triggers while holding the input_lock and input_register_handler() takes the input_lock this means that a triggers activate method cannot directly call input_register_handler() as the old ledtrig-input-events code is doing.

Quoted 8 lines

The initial implementation of the input-events trigger mainly did not use the simple LED trigger mechanism because that mechanism had an issue with the initial state of a newly activated LED not matching the last led_trigger_event() call for the trigger. This issue has been fixed in commit 822c91e72eac ("leds: trigger: Store brightness set by led_trigger_event()").

[...]

Applied, thanks!

[1/1] leds: trigger: input-events: Rewrite to fix a serious locking issue

      commit: 284ad8e7d5eeb1659b63f44fd094373900322de6

--
Lee Jones [李琼斯]