Skip to contentSkip to conversation

Refactor, fix and improve NanoPi R6 series

PATCH In review Sebastian Kropatsch 4 participants 13 messages Jun 12, 2024 – Jun 20, 2024

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

cover Refactor, fix and improve NanoPi R6 series

Hello,

This patch series fixes a lot of minor issues in the current devicetree for the FriendlyElec NanoPi R6 series (R6C and R6S), as well as adding support for the GPU and one USB3 port which was previously disabled.

To aid with these patches, I have refactored the devicetrees in such a way that they will now share a common dtsi source file in a similar fashion than what the NanoPi R5C and R5S are already doing. This makes changes which only affect one of the boards easier, less error-prone and more maintainable. Also we don't need to work with /delete-node/ and /delete-property/ this way :)

Cheers,
Sebastian

PS: Additional comments in patch 2 and 3.

---

Sebastian Kropatsch (5):
arm64: dts: rockchip: Add common definitions for NanoPi R6C and R6S
arm64: dts: rockchip: Fix regulators, gmac and naming on NanoPi

    R6C/R6S

arm64: dts: rockchip: Improve LEDs on NanoPi R6C/R6S
arm64: dts: rockchip: Enable lower USB3 port on NanoPi R6C/R6S
arm64: dts: rockchip: Enable GPU on NanoPi R6C/R6S

 ...-nanopi-r6s.dts => rk3588s-nanopi-r6.dtsi} | 242 +++---
 .../boot/dts/rockchip/rk3588s-nanopi-r6c.dts  |  48 +-
 .../boot/dts/rockchip/rk3588s-nanopi-r6s.dts  | 743 +-----------------
 3 files changed, 193 insertions(+), 840 deletions(-)
 copy arch/arm64/boot/dts/rockchip/{rk3588s-nanopi-r6s.dts => rk3588s-nanopi-r6.dtsi} (81%)
Signature · 1 line
2.43.0
#1 lore raw

PATCH 1/5 arm64: dts: rockchip: Add common definitions for NanoPi R6C and R6S

The FriendlyElec NanoPi R6C and R6S are quite similar boards, although they differ in:
- M.2 M-Key connector vs second RTL8125BG Ethernet port
- One of the LEDs has a different function on each board
- 12-pin GPIO FPC vs 30-pin GPIO header
- R6S has a PWM-based IR receiver while the R6C has not
- R6S has a 5V fan connector while the R6C has not

Refactor their DT files by adding a common definitions file to improve differentiation clarity between both boards and to make hardware-specific DT changes easier in the long run. Do not introduce any functional changes.

---
 ...-nanopi-r6s.dts => rk3588s-nanopi-r6.dtsi} |   7 +-
 .../boot/dts/rockchip/rk3588s-nanopi-r6c.dts  |   2 +-
 .../boot/dts/rockchip/rk3588s-nanopi-r6s.dts  | 756 +-----------------
 3 files changed, 7 insertions(+), 758 deletions(-)
 copy arch/arm64/boot/dts/rockchip/{rk3588s-nanopi-r6s.dts => rk3588s-nanopi-r6.dtsi} (99%)
arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi renamed from arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6s.dts +3 -4
similarity index 99%
copy from arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6s.dts
copy to arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi
index 4fa644ae510c..e68d4071400e 100644
@@ -1,4 +1,7 @@
 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Common devicetree definitions for the NanoPi R6C and R6S
+ */
 
 /dts-v1/;
 
@@ -8,9 +11,6 @@
 #include "rk3588s.dtsi"
 
 / {
-	model = "FriendlyElec NanoPi R6S";
-	compatible = "friendlyarm,nanopi-r6s", "rockchip,rk3588s";
-
 	aliases {
 		ethernet0 = &gmac1;
 		mmc0 = &sdmmc;
@@ -74,7 +74,6 @@ lan1_led: led-2 {
 		};
 
 		lan2_led: led-3 {
-			label = "lan2_led";
 			gpios = <&gpio1 RK_PC4 GPIO_ACTIVE_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&lan2_led_pin>;
arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6c.dts +1 -1
index 497bbb57071f..ccc5e4627517 100644
@@ -2,7 +2,7 @@
 
 /dts-v1/;
 
-#include "rk3588s-nanopi-r6s.dts"
+#include "rk3588s-nanopi-r6.dtsi"
 
 / {
 	model = "FriendlyElec NanoPi R6C";
arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6s.dts +3 -753

766 lines not on this page · raw message

Signature · 1 line
2.43.0
maintainer
#2 lore raw

Re: [PATCH 1/5] arm64: dts: rockchip: Add common definitions for NanoPi R6C and R6S

Am Mittwoch, 12. Juni 2024, 22:48:10 CEST schrieb Sebastian Kropatsch:

Quoted 59 lines

The FriendlyElec NanoPi R6C and R6S are quite similar boards, although they differ in:
- M.2 M-Key connector vs second RTL8125BG Ethernet port
- One of the LEDs has a different function on each board
- 12-pin GPIO FPC vs 30-pin GPIO header
- R6S has a PWM-based IR receiver while the R6C has not
- R6S has a 5V fan connector while the R6C has not

Refactor their DT files by adding a common definitions file to improve differentiation clarity between both boards and to make hardware-specific DT changes easier in the long run. Do not introduce any functional changes.

---
 ...-nanopi-r6s.dts => rk3588s-nanopi-r6.dtsi} |   7 +-
 .../boot/dts/rockchip/rk3588s-nanopi-r6c.dts  |   2 +-
 .../boot/dts/rockchip/rk3588s-nanopi-r6s.dts  | 756 +-----------------
 3 files changed, 7 insertions(+), 758 deletions(-)
 copy arch/arm64/boot/dts/rockchip/{rk3588s-nanopi-r6s.dts => rk3588s-nanopi-r6.dtsi} (99%)
arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi renamed from arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6s.dts +3 -4
similarity index 99%
copy from arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6s.dts
copy to arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi
index 4fa644ae510c..e68d4071400e 100644
@@ -1,4 +1,7 @@
 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Common devicetree definitions for the NanoPi R6C and R6S
+ */
 
 /dts-v1/;
 
@@ -8,9 +11,6 @@
 #include "rk3588s.dtsi"
 
 / {
-	model = "FriendlyElec NanoPi R6S";
-	compatible = "friendlyarm,nanopi-r6s", "rockchip,rk3588s";
-
 	aliases {
 		ethernet0 = &gmac1;
 		mmc0 = &sdmmc;
@@ -74,7 +74,6 @@ lan1_led: led-2 {
 		};
 
 		lan2_led: led-3 {
-			label = "lan2_led";
 			gpios = <&gpio1 RK_PC4 GPIO_ACTIVE_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&lan2_led_pin>;
arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6c.dts +0 -0
index 497bbb57071f..ccc5e4627517 100644

arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6c.dts line 8

Quoted 8 lines
arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6c.dts +1 -1
@@ -2,7 +2,7 @@
 
 /dts-v1/;
 
-#include "rk3588s-nanopi-r6s.dts"
+#include "rk3588s-nanopi-r6.dtsi"
 
 / {
 	model = "FriendlyElec NanoPi R6C";

you didn't add a label for that led here.

Though I think it might very well be much nicer to just define the led with differing function in each board separately.

Especially as the phandle in the new dtsi now still reference the removed label.

Heiko

#3 lore raw

PATCH 2/5 arm64: dts: rockchip: Fix regulators, gmac and naming on NanoPi R6C/R6S

In reply to Sebastian Kropatsch

Fix the alphabetical ordering in some nodes and rename some regulators and pins to match the schematics [1][2] as well as to adhere to preferred naming schemes.

In addition to that:
* vcc_3v3_sd_s0: Fix voltage to be 3.3V
* vcc3v3_pcie:
- Move to NanoPi R6C, this power switch is not available on R6S
- Fix vin-supply (is vcc_5v0 per schematics)
- Add gpios/pincrtl to enable power
* vcc5v0_usb: Remove this regulator since according to the schematics, vcc5v0_host_20 and vcc5v0_usb_otg0 are directly powered by vcc_5v0
* gmac1: Add rx_delay of 0 (no delay since phy-mode = "rgmii-rxid")
* rgmii_phy1: Add phy-supply as seen in schematics
* pcie2*:
- Add pinctrl reset pins
- Update vpcie3v3-supply to match the schematics
* sdhci: Add vmmc-supply and vqmmc-supply

Links:
[1] https://wiki.friendlyelec.com/wiki/images/f/f7/NanoPi_R6C_2302_SCH.PDF
[2] https://wiki.friendlyelec.com/wiki/images/2/2f/NanoPi_R6S_2208_SCH.PDF

Fixes f1b11f43b3e9 ("arm64: dts: rockchip: Add support for NanoPi R6S")

---

I didn't want to spam many patches with small fixes/improvements, so this one patch includes lots of small changes. Let me know if another method is preferred :)

---
 .../boot/dts/rockchip/rk3588s-nanopi-r6.dtsi  | 169 +++++++++---------
 .../boot/dts/rockchip/rk3588s-nanopi-r6c.dts  |  28 +++
 .../boot/dts/rockchip/rk3588s-nanopi-r6s.dts  |   5 +
 3 files changed, 122 insertions(+), 80 deletions(-)
arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi +89 -80
index e68d4071400e..8b90bae28302 100644
@@ -21,7 +21,7 @@ chosen {
 		stdout-path = "serial2:1500000n8";
 	};
 
-	adc-keys {
+	adc-key-maskrom {
 		compatible = "adc-keys";
 		io-channels = <&saradc 0>;
 		io-channel-names = "buttons";
@@ -41,10 +41,10 @@ gpio-keys {
 		pinctrl-0 = <&key1_pin>;
 
 		button-user {
-			label = "User";
-			linux,code = <BTN_1>;
-			gpios = <&gpio1 RK_PC0 GPIO_ACTIVE_LOW>;
 			debounce-interval = <50>;
+			gpios = <&gpio1 RK_PC0 GPIO_ACTIVE_LOW>;
+			label = "User Button";
+			linux,code = <BTN_1>;
 		};
 	};
 
@@ -80,26 +80,27 @@ lan2_led: led-3 {
 		};
 	};
 
-	vcc5v0_sys: vcc5v0-sys-regulator {
+	vcc_5v0: regulator-vcc-5v0 {
 		compatible = "regulator-fixed";
-		regulator-name = "vcc5v0_sys";
 		regulator-always-on;
 		regulator-boot-on;
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
+		regulator-name = "vcc_5v0";
 	};
 
-	vcc_1v1_nldo_s3: vcc-1v1-nldo-s3-regulator {
+	vcc_1v1_nldo_s3: regulator-vcc-1v1-nldo-s3 {
 		compatible = "regulator-fixed";
-		regulator-name = "vcc_1v1_nldo_s3";
 		regulator-always-on;
 		regulator-boot-on;
 		regulator-min-microvolt = <1100000>;
 		regulator-max-microvolt = <1100000>;
-		vin-supply = <&vcc5v0_sys>;
+		regulator-name = "vcc_1v1_nldo_s3";
+		vin-supply = <&vcc_5v0>;
 	};
 
-	vcc_3v3_s0: vcc-3v3-s0-regulator {
+	/* SY6280AAC power switch (U3824 in schematics) */
+	vcc_3v3_s0: regulator-vcc-3v3-s0 {
 		compatible = "regulator-fixed";
 		regulator-always-on;
 		regulator-boot-on;
@@ -109,61 +110,45 @@ vcc_3v3_s0: vcc-3v3-s0-regulator {
 		vin-supply = <&vcc_3v3_s3>;
 	};
 
-	vcc_3v3_sd_s0: vcc-3v3-sd-s0-regulator {
+	vcc_3v3_sd_s0: regulator-vcc-3v3-sd-s0 {
 		compatible = "regulator-fixed";
 		enable-active-high;
 		gpios = <&gpio4 RK_PB4 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&sd_s0_pwr>;
-		regulator-name = "vcc_3v3_sd_s0";
-		regulator-boot-on;
-		regulator-max-microvolt = <3000000>;
-		regulator-min-microvolt = <3000000>;
-		vin-supply = <&vcc_3v3_s3>;
-	};
-
-	vcc_3v3_pcie20: vcc3v3-pcie20-regulator {
-		compatible = "regulator-fixed";
-		regulator-name = "vcc_3v3_pcie20";
-		regulator-always-on;
 		regulator-boot-on;
-		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "vcc_3v3_sd_s0";
 		vin-supply = <&vcc_3v3_s3>;
 	};
 
-	vcc5v0_usb: vcc5v0-usb-regulator {
-		compatible = "regulator-fixed";
-		regulator-name = "vcc5v0_usb";
-		regulator-always-on;
-		regulator-boot-on;
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		vin-supply = <&vcc5v0_sys>;
-	};
-
-	vcc5v0_usb_otg0: vcc5v0-usb-otg0-regulator {
+	/* SY6280AAC power switch (U9539 in schematics) */
+	/* For USB 2.0 Type-A port */
+	vcc_5v0_host_20: regulator-vcc-5v0-host-20 {
 		compatible = "regulator-fixed";
 		enable-active-high;
-		gpios = <&gpio1 RK_PD2 GPIO_ACTIVE_HIGH>;
+		gpios = <&gpio4 RK_PB5 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
-		pinctrl-0 = <&typec5v_pwren>;
-		regulator-name = "vcc5v0_usb_otg0";
+		pinctrl-0 = <&usb_host_pwren_h>;
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
-		vin-supply = <&vcc5v0_usb>;
+		regulator-name = "vcc_5v0_host_20";
+		vin-supply = <&vcc_5v0>;
 	};
 
-	vcc5v0_host_20: vcc5v0-host-20-regulator {
+	/* SY6280AAC power switch (U9538 in schematics) */
+	/* For USB 3.0 Type-A port */
+	vcc5v0_usb_otg0: regulator-vcc5v0-usb-otg0 {
 		compatible = "regulator-fixed";
 		enable-active-high;
-		gpios = <&gpio4 RK_PB5 GPIO_ACTIVE_HIGH>;
+		gpios = <&gpio1 RK_PD2 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
-		pinctrl-0 = <&vcc5v0_host20_en>;
-		regulator-name = "vcc5v0_host_20";
+		pinctrl-0 = <&typec5v_pwren_h>;
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
-		vin-supply = <&vcc5v0_usb>;
+		regulator-name = "vcc5v0_usb_otg0";
+		vin-supply = <&vcc_5v0>;
 	};
 };
 
@@ -211,12 +196,13 @@ &gmac1 {
 	clock_in_out = "output";
 	phy-handle = <&rgmii_phy1>;
 	phy-mode = "rgmii-rxid";
+	pinctrl-names = "default";
 	pinctrl-0 = <&gmac1_miim
 		     &gmac1_tx_bus2
 		     &gmac1_rx_bus2
 		     &gmac1_rgmii_clk
 		     &gmac1_rgmii_bus>;
-	pinctrl-names = "default";
+	rx_delay = <0x00>;
 	tx_delay = <0x42>;
 	status = "okay";
 };
@@ -230,13 +216,13 @@ vdd_cpu_big0_s0: regulator@42 {
 		compatible = "rockchip,rk8602";
 		reg = <0x42>;
 		fcs,suspend-voltage-selector = <1>;
-		regulator-name = "vdd_cpu_big0_s0";
 		regulator-always-on;
 		regulator-boot-on;
 		regulator-min-microvolt = <550000>;
 		regulator-max-microvolt = <1050000>;
+		regulator-name = "vdd_cpu_big0_s0";
 		regulator-ramp-delay = <2300>;
-		vin-supply = <&vcc5v0_sys>;
+		vin-supply = <&vcc_5v0>;
 
 		regulator-state-mem {
 			regulator-off-in-suspend;
@@ -247,13 +233,13 @@ vdd_cpu_big1_s0: regulator@43 {
 		compatible = "rockchip,rk8603", "rockchip,rk8602";
 		reg = <0x43>;
 		fcs,suspend-voltage-selector = <1>;
-		regulator-name = "vdd_cpu_big1_s0";
 		regulator-always-on;
 		regulator-boot-on;
 		regulator-min-microvolt = <550000>;
 		regulator-max-microvolt = <1050000>;
+		regulator-name = "vdd_cpu_big1_s0";
 		regulator-ramp-delay = <2300>;
-		vin-supply = <&vcc5v0_sys>;
+		vin-supply = <&vcc_5v0>;
 
 		regulator-state-mem {
 			regulator-off-in-suspend;
@@ -268,13 +254,13 @@ vdd_npu_s0: regulator@42 {
 		compatible = "rockchip,rk8602";
 		reg = <0x42>;
 		fcs,suspend-voltage-selector = <1>;
-		regulator-name = "vdd_npu_s0";
+		regulator-always-on;
+		regulator-boot-on;
 		regulator-min-microvolt = <550000>;
 		regulator-max-microvolt = <950000>;
+		regulator-name = "vdd_npu_s0";
 		regulator-ramp-delay = <2300>;
-		regulator-boot-on;
-		regulator-always-on;
-		vin-supply = <&vcc5v0_sys>;
+		vin-supply = <&vcc_5v0>;
 
 		regulator-state-mem {
 			regulator-off-in-suspend;
@@ -293,35 +279,43 @@ hym8563: rtc@51 {
 		reg = <0x51>;
 		#clock-cells = <0>;
 		clock-output-names = "hym8563";
-		pinctrl-names = "default";
-		pinctrl-0 = <&rtc_int>;
 		interrupt-parent = <&gpio0>;
 		interrupts = <RK_PB0 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&rtc_int>;
 		wakeup-source;
 	};
 };
 
+/* RTL8211F-CG Ethernet */
 &mdio1 {
 	rgmii_phy1: ethernet-phy@1 {
 		compatible = "ethernet-phy-id001c.c916";
 		reg = <0x1>;
+		phy-supply = <&vcc_3v3_s0>;
 		pinctrl-names = "default";
-		pinctrl-0 = <&rtl8211f_rst>;
+		pinctrl-0 = <&gmac1_rstn_l>;
 		reset-assert-us = <20000>;
 		reset-deassert-us = <100000>;
 		reset-gpios = <&gpio3 RK_PB7 GPIO_ACTIVE_LOW>;
 	};
 };
 
+/* RTL8125BG Ethernet */
 &pcie2x1l1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie20x1_1_perstn_m2>;
 	reset-gpios = <&gpio1 RK_PA7 GPIO_ACTIVE_HIGH>;
-	vpcie3v3-supply = <&vcc_3v3_pcie20>;
+	vpcie3v3-supply = <&vcc_3v3_s3>;
 	status = "okay";
 };
 
+/* R6C: M.2 M-Key socket */
+/* R6S: RTL8125BG Ethernet */
 &pcie2x1l2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie20x1_2_perstn_m0>;
 	reset-gpios = <&gpio3 RK_PD1 GPIO_ACTIVE_HIGH>;
-	vpcie3v3-supply = <&vcc_3v3_pcie20>;
 	status = "okay";
 };
 
@@ -360,24 +354,34 @@ rtc_int: rtc-int {
 		};
 	};
 
+	pcie {
+		pcie20x1_1_perstn_m2: pcie2x1-1-rst {
+			rockchip,pins = <1 RK_PA7 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		pcie20x1_2_perstn_m0: pcie2x1-2-rst {
+			rockchip,pins = <3 RK_PD1 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
 	sdmmc {
-		sd_s0_pwr: sd-s0-pwr {
+		sd_s0_pwr: sd-pwr {
 			rockchip,pins = <4 RK_PB4 RK_FUNC_GPIO &pcfg_pull_up>;
 		};
 	};
 
 	usb {
-		typec5v_pwren: typec5v-pwren {
+		typec5v_pwren_h: usb3-pwren {
 			rockchip,pins = <1 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
 		};
 
-		vcc5v0_host20_en: vcc5v0-host20-en {
+		usb_host_pwren_h: usb2-pwren {
 			rockchip,pins = <4 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>;
 		};
 	};
 
 	rtl8211f {
-		rtl8211f_rst: rtl8211f-rst {
+		gmac1_rstn_l: rtl8211f-rst {
 			rockchip,pins = <3 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
 		};
 	};
@@ -388,15 +392,19 @@ &saradc {
 	status = "okay";
 };
 
+/* eMMC */
 &sdhci {
 	bus-width = <8>;
-	no-sdio;
+	mmc-hs200-1_8v;
 	no-sd;
+	no-sdio;
 	non-removable;
-	mmc-hs200-1_8v;
+	vmmc-supply = <&vcc_3v3_s3>;
+	vqmmc-supply = <&vcc_1v8_s3>;
 	status = "okay";
 };
 
+/* microSD card */
 &sdmmc {
 	bus-width = <4>;
 	cap-sd-highspeed;
@@ -411,16 +419,15 @@ &sdmmc {
 };
 
 &spi2 {
-	status = "okay";
 	assigned-clocks = <&cru CLK_SPI2>;
 	assigned-clock-rates = <200000000>;
+	num-cs = <1>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&spi2m2_cs0 &spi2m2_pins>;
-	num-cs = <1>;
+	status = "okay";
 
-	pmic@0 {
+	rk806_single: pmic@0 {
 		compatible = "rockchip,rk806";
-		spi-max-frequency = <1000000>;
 		reg = <0x0>;
 
 		interrupt-parent = <&gpio0>;
@@ -430,23 +437,24 @@ pmic@0 {
 		pinctrl-0 = <&pmic_pins>, <&rk806_dvs1_null>,
 			    <&rk806_dvs2_null>, <&rk806_dvs3_null>;
 
+		spi-max-frequency = <1000000>;
 		system-power-controller;
 
-		vcc1-supply = <&vcc5v0_sys>;
-		vcc2-supply = <&vcc5v0_sys>;
-		vcc3-supply = <&vcc5v0_sys>;
-		vcc4-supply = <&vcc5v0_sys>;
-		vcc5-supply = <&vcc5v0_sys>;
-		vcc6-supply = <&vcc5v0_sys>;
-		vcc7-supply = <&vcc5v0_sys>;
-		vcc8-supply = <&vcc5v0_sys>;
-		vcc9-supply = <&vcc5v0_sys>;
-		vcc10-supply = <&vcc5v0_sys>;
+		vcc1-supply = <&vcc_5v0>;
+		vcc2-supply = <&vcc_5v0>;
+		vcc3-supply = <&vcc_5v0>;
+		vcc4-supply = <&vcc_5v0>;
+		vcc5-supply = <&vcc_5v0>;
+		vcc6-supply = <&vcc_5v0>;
+		vcc7-supply = <&vcc_5v0>;
+		vcc8-supply = <&vcc_5v0>;
+		vcc9-supply = <&vcc_5v0>;
+		vcc10-supply = <&vcc_5v0>;
 		vcc11-supply = <&vcc_2v0_pldo_s3>;
-		vcc12-supply = <&vcc5v0_sys>;
+		vcc12-supply = <&vcc_5v0>;
 		vcc13-supply = <&vcc_1v1_nldo_s3>;
 		vcc14-supply = <&vcc_1v1_nldo_s3>;
-		vcca-supply = <&vcc5v0_sys>;
+		vcca-supply = <&vcc_5v0>;
 
 		gpio-controller;
 		#gpio-cells = <2>;
@@ -745,10 +753,11 @@ &u2phy2 {
 };
 
 &u2phy2_host {
-	phy-supply = <&vcc5v0_host_20>;
+	phy-supply = <&vcc_5v0_host_20>;
 	status = "okay";
 };
 
+/* Debug UART */
 &uart2 {
 	pinctrl-0 = <&uart2m0_xfer>;
 	status = "okay";
arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6c.dts +28 -0
index ccc5e4627517..24dcd3e07ea7 100644
@@ -7,8 +7,36 @@
 / {
 	model = "FriendlyElec NanoPi R6C";
 	compatible = "friendlyarm,nanopi-r6c", "rockchip,rk3588s";
+
+	/* MP2143DJ power switch (U9536 in schematics) */
+	vcc3v3_pcie: regulator-vcc3v3-pcie {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpios = <&gpio3 RK_PC6 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pcie20x1_2_con_pwren>;
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "vcc3v3_pcie";
+		vin-supply = <&vcc_5v0>;
+	};
 };
 
 &lan2_led {
 	label = "user_led";
 };
+
+/* M.2 M-Key socket */
+&pcie2x1l2 {
+	vpcie3v3-supply = <&vcc3v3_pcie>;
+};
+
+&pinctrl {
+	pcie {
+		pcie20x1_2_con_pwren: pcie20x1-2-con-pwren {
+			rockchip,pins = <3 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6s.dts +5 -0
index 9c3e0b0daaac..d24110b6cf5d 100644
@@ -12,3 +12,8 @@ / {
 &lan2_led {
 	label = "lan2_led";
 };
+
+/* RTL8125BG Ethernet */
+&pcie2x1l2 {
+	vpcie3v3-supply = <&vcc_3v3_s3>;
+};
Signature · 1 line
2.43.0
maintainer
#4 lore raw

Re: [PATCH 2/5] arm64: dts: rockchip: Fix regulators, gmac and naming on NanoPi R6C/R6S

Am Mittwoch, 12. Juni 2024, 22:48:11 CEST schrieb Sebastian Kropatsch:

Quoted 3 lines

Fix the alphabetical ordering in some nodes and rename some regulators and pins to match the schematics [1][2] as well as to adhere to preferred naming schemes.

General rule of thumb, when you need an "and" in your subject or a list like the above - you definitly want to split the change into multiple commits.

Quoted 6 lines

In addition to that:
* vcc_3v3_sd_s0: Fix voltage to be 3.3V
* vcc3v3_pcie:
- Move to NanoPi R6C, this power switch is not available on R6S
- Fix vin-supply (is vcc_5v0 per schematics)
- Add gpios/pincrtl to enable power

this defnitly needs its own patch

Quoted 1 line

* vcc5v0_usb: Remove this regulator since according to the schematics,

this too

Quoted 1 line

* vcc5v0_host_20 and vcc5v0_usb_otg0 are directly powered by vcc_5v0

this could be grouped together with the 3.3v change

Quoted 1 line

* gmac1: Add rx_delay of 0 (no delay since phy-mode = "rgmii-rxid")

with rxid mode, why is the rx_delay needed at all? Shouldn't this just work without the property?

Quoted 1 line

* rgmii_phy1: Add phy-supply as seen in schematics

separate patch

Quoted 3 lines

* pcie2*:
- Add pinctrl reset pins
- Update vpcie3v3-supply to match the schematics

separate patch

Quoted 1 line

* sdhci: Add vmmc-supply and vqmmc-supply

separate patch

Heiko

#5 lore raw

Re: [PATCH 2/5] arm64: dts: rockchip: Fix regulators, gmac and naming on NanoPi R6C/R6S

Hello,

Am 20.06.2024 um 20:39 schrieb Heiko Stübner:

Quoted 8 lines

Am Mittwoch, 12. Juni 2024, 22:48:11 CEST schrieb Sebastian Kropatsch:

Quoted 3 lines

Fix the alphabetical ordering in some nodes and rename some regulators and pins to match the schematics [1][2] as well as to adhere to preferred naming schemes.

General rule of thumb, when you need an "and" in your subject or a list like the above - you definitly want to split the change into multiple commits.

Thanks for the advice! I wasn't sure and didn't want to spam the list. Also, my email provider only allows a limited number of emails to be sent every day (series with 5 patches, with 9 recipients = 45 emails sent). So I might have to send the patch series by spanning the different patches over multiple days.

If anyone knows an email provider which is better suited for this kind of open source work/mailing lists and is also privacy respecting, please let me know :)

I will definitely split these changes into separate commits.

Quoted 13 lines
Quoted 6 lines

In addition to that:
* vcc_3v3_sd_s0: Fix voltage to be 3.3V
* vcc3v3_pcie:
- Move to NanoPi R6C, this power switch is not available on R6S
- Fix vin-supply (is vcc_5v0 per schematics)
- Add gpios/pincrtl to enable power

this defnitly needs its own patch

Quoted 1 line

* vcc5v0_usb: Remove this regulator since according to the schematics,

this too

Quoted 8 lines
Quoted 1 line

* vcc5v0_host_20 and vcc5v0_usb_otg0 are directly powered by vcc_5v0

this could be grouped together with the 3.3v change

Quoted 1 line

* gmac1: Add rx_delay of 0 (no delay since phy-mode = "rgmii-rxid")

with rxid mode, why is the rx_delay needed at all? Shouldn't this just work without the property?

In theory yes, but with the property missing, you'll get a warning message in dmesg which says:

	Can not read property: rx_delay.
	Set rx_delay to 0x10

So it will set the rx_delay to a value which is not 0, even if rxid mode is selected. I guess this is something which can be fixed in the driver, but that may be beyond my abilities.
Setting the rx_delay to 0 gets rid of this warning, so it seems to be a viable workaround.

Quoted 8 lines
Quoted 1 line

* rgmii_phy1: Add phy-supply as seen in schematics

separate patch

Quoted 3 lines

* pcie2*:
- Add pinctrl reset pins
- Update vpcie3v3-supply to match the schematics

Quoted 6 lines

separate patch

Quoted 1 line

* sdhci: Add vmmc-supply and vqmmc-supply

separate patch

Thanks,
Sebastian

#6 lore raw

PATCH 3/5 arm64: dts: rockchip: Improve LEDs on NanoPi R6C/R6S

In reply to Sebastian Kropatsch

Move led-3 node into NanoPi R6C/R6S's source files since they have different functionalities on each board: On the R6S this LED is used to signal LAN2 link up, while on the R6C this LED does not have a pre-defined purpose.

In addition to that:
- Remove deprecated label property
- Add color and function properties
- Add linux,default-trigger to trigger on Ethernet link

---

DT validation doesn't like the 'linux,default-trigger = "stmmac-0:01:link"' properties, since "*:link" is not a valid value according to [Documentation/devicetree/bindings/leds/common.yaml]. These LEDs do have the specific purpose to show if an Ethernet link is up though. There is one LED for each Ethernet port and they are labeled WAN and LAN.
Using the 'linux,default-trigger' like this does work perfectly fine with this solution. I could not find another way to achieve this. Please let me know if there is a better way.
Maybe it would also be valid to add an entry to the DT bindings file to allow "*:link" as a value for 'linux,default-trigger'?

The same problem also applies to the NanoPi R5C/R5S which also has these LEDs to show Ethernet link up, although in their current DT these LEDs are simply not functional.

---
 .../boot/dts/rockchip/rk3588s-nanopi-r6.dtsi  | 32 +++++++------------
 .../boot/dts/rockchip/rk3588s-nanopi-r6c.dts  | 22 ++++++++++---
 .../boot/dts/rockchip/rk3588s-nanopi-r6s.dts  | 26 +++++++++++++--
 3 files changed, 54 insertions(+), 26 deletions(-)
arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi +12 -20
index 8b90bae28302..69d0f1f2349b 100644
@@ -8,6 +8,7 @@
 #include <dt-bindings/pinctrl/rockchip.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
 #include "rk3588s.dtsi"
 
 / {
@@ -52,7 +53,8 @@ leds {
 		compatible = "gpio-leds";
 
 		sys_led: led-0 {
-			label = "sys_led";
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_HEARTBEAT;
 			gpios = <&gpio1 RK_PC1 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 			pinctrl-names = "default";
@@ -60,24 +62,22 @@ sys_led: led-0 {
 		};
 
 		wan_led: led-1 {
-			label = "wan_led";
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_WAN;
 			gpios = <&gpio1 RK_PC2 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "stmmac-0:01:link";
 			pinctrl-names = "default";
 			pinctrl-0 = <&wan_led_pin>;
 		};
 
 		lan1_led: led-2 {
-			label = "lan1_led";
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_LAN;
 			gpios = <&gpio1 RK_PC3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "r8169-3-3100:00:link";
 			pinctrl-names = "default";
 			pinctrl-0 = <&lan1_led_pin>;
 		};
-
-		lan2_led: led-3 {
-			gpios = <&gpio1 RK_PC4 GPIO_ACTIVE_HIGH>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&lan2_led_pin>;
-		};
 	};
 
 	vcc_5v0: regulator-vcc-5v0 {
@@ -328,23 +328,15 @@ key1_pin: key1-pin {
 
 	gpio-leds {
 		sys_led_pin: sys-led-pin {
-			rockchip,pins =
-				<1 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>;
+			rockchip,pins = <1 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>;
 		};
 
 		wan_led_pin: wan-led-pin {
-			rockchip,pins =
-				<1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
+			rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
 		};
 
 		lan1_led_pin: lan1-led-pin {
-			rockchip,pins =
-				<1 RK_PC3 RK_FUNC_GPIO &pcfg_pull_none>;
-		};
-
-		lan2_led_pin: lan2-led-pin {
-			rockchip,pins =
-				<1 RK_PC4 RK_FUNC_GPIO &pcfg_pull_none>;
+			rockchip,pins = <1 RK_PC3 RK_FUNC_GPIO &pcfg_pull_none>;
 		};
 	};
 
arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6c.dts +18 -4
index 24dcd3e07ea7..d1b6aa033abc 100644
@@ -8,6 +8,18 @@ / {
 	model = "FriendlyElec NanoPi R6C";
 	compatible = "friendlyarm,nanopi-r6c", "rockchip,rk3588s";
 
+	leds {
+		compatible = "gpio-leds";
+
+		led1_led: led-3 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = "led1";
+			gpios = <&gpio1 RK_PC4 GPIO_ACTIVE_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&led1_led_pin>;
+		};
+	};
+
 	/* MP2143DJ power switch (U9536 in schematics) */
 	vcc3v3_pcie: regulator-vcc3v3-pcie {
 		compatible = "regulator-fixed";
@@ -24,16 +36,18 @@ vcc3v3_pcie: regulator-vcc3v3-pcie {
 	};
 };
 
-&lan2_led {
-	label = "user_led";
-};
-
 /* M.2 M-Key socket */
 &pcie2x1l2 {
 	vpcie3v3-supply = <&vcc3v3_pcie>;
 };
 
 &pinctrl {
+	gpio-leds {
+		led1_led_pin: led1-led-pin {
+			rockchip,pins = <1 RK_PC4 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
 	pcie {
 		pcie20x1_2_con_pwren: pcie20x1-2-con-pwren {
 			rockchip,pins = <3 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6s.dts +24 -2
index d24110b6cf5d..09afbc0a2581 100644
@@ -7,13 +7,35 @@
 / {
 	model = "FriendlyElec NanoPi R6S";
 	compatible = "friendlyarm,nanopi-r6s", "rockchip,rk3588s";
+
+	leds {
+		compatible = "gpio-leds";
+
+		lan2_led: led-3 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_LAN;
+			function-enumerator = <2>;
+			gpios = <&gpio1 RK_PC4 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "r8169-4-4100:00:link";
+			pinctrl-names = "default";
+			pinctrl-0 = <&lan2_led_pin>;
+		};
+	};
 };
 
-&lan2_led {
-	label = "lan2_led";
+&lan1_led {
+	function-enumerator = <1>;
 };
 
 /* RTL8125BG Ethernet */
 &pcie2x1l2 {
 	vpcie3v3-supply = <&vcc_3v3_s3>;
 };
+
+&pinctrl {
+	gpio-leds {
+		lan2_led_pin: lan2-led-pin {
+			rockchip,pins = <1 RK_PC4 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
Signature · 1 line
2.43.0
#7 lore raw

Re: [PATCH 3/5] arm64: dts: rockchip: Improve LEDs on NanoPi R6C/R6S

kernel test robot noticed the following build warnings:

Hi Sebastian,

kernel test robot noticed the following build warnings:

[auto build test WARNING on rockchip/for-next]
[also build test WARNING on linus/master v6.10-rc3 next-20240613] [If your patch is applied to the wrong git tree, kindly drop us a note. And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch#_base_tree_information]

url:    https://github.com/intel-lab-lkp/linux/commits/Sebastian-Kropatsch/arm64-dts-rockchip-Add-common-definitions-for-NanoPi-R6C-and-R6S/20240613-045639
base:   https://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip.git for-next
patch link:    https://lore.kernel.org/r/20240612205056.397204-4-seb-dev%40mail.de
patch subject: [PATCH 3/5] arm64: dts: rockchip: Improve LEDs on NanoPi R6C/R6S
config: arm64-randconfig-051-20240614 (https://download.01.org/0day-ci/archive/20240614/[email protected]/config)
compiler: aarch64-linux-gcc (GCC) 13.2.0
dtschema version: 2024.6.dev1+g833054f
reproduce (this is a W=1 build): (https://download.01.org/0day-ci/archive/20240614/[email protected]/reproduce)

If you fix the issue in a separate patch/commit (i.e. not just a new version of the same patch/commit), kindly add following tags
| Reported-by: kernel test robot <[email protected]>
| Closes: https://lore.kernel.org/oe-kbuild-all/[email protected]/

dtcheck warnings: (new ones prefixed by >>)

>> arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6s.dtb: leds: led-1:linux,default-trigger: 'oneOf' conditional failed, one must be fixed:
   	'stmmac-0:01:link' is not one of ['backlight', 'default-on', 'heartbeat', 'disk-activity', 'disk-read', 'disk-write', 'timer', 'pattern', 'audio-micmute', 'audio-mute', 'bluetooth-power', 'flash', 'kbd-capslock', 'mtd', 'nand-disk', 'none', 'torch', 'usb-gadget', 'usb-host', 'usbport']
   	'stmmac-0:01:link' does not match '^cpu[0-9]*$'
   	'stmmac-0:01:link' does not match '^hci[0-9]+-power$'
   	'stmmac-0:01:link' does not match '^mmc[0-9]+$'
   	'stmmac-0:01:link' does not match '^phy[0-9]+tx$'
   	from schema $id: http://devicetree.org/schemas/leds/leds-gpio.yaml#
>> arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6s.dtb: leds: led-1: Unevaluated properties are not allowed ('linux,default-trigger' was unexpected)

from schema $id: http://devicetree.org/schemas/leds/leds-gpio.yaml#
arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6s.dtb: leds: led-2:linux,default-trigger: 'oneOf' conditional failed, one must be fixed:
'r8169-3-3100:00:link' is not one of ['backlight', 'default-on', 'heartbeat', 'disk-activity', 'disk-read', 'disk-write', 'timer', 'pattern', 'audio-micmute', 'audio-mute', 'bluetooth-power', 'flash', 'kbd-capslock', 'mtd', 'nand-disk', 'none', 'torch', 'usb-gadget', 'usb-host', 'usbport'] 'r8169-3-3100:00:link' does not match '^cpu[0-9]*$'
'r8169-3-3100:00:link' does not match '^hci[0-9]+-power$'
'r8169-3-3100:00:link' does not match '^mmc[0-9]+$'
'r8169-3-3100:00:link' does not match '^phy[0-9]+tx$'
from schema $id: http://devicetree.org/schemas/leds/leds-gpio.yaml#
arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6s.dtb: leds: led-2: Unevaluated properties are not allowed ('linux,default-trigger' was unexpected)
from schema $id: http://devicetree.org/schemas/leds/leds-gpio.yaml#
--

>> arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6c.dtb: leds: led-1:linux,default-trigger: 'oneOf' conditional failed, one must be fixed:
   	'stmmac-0:01:link' is not one of ['backlight', 'default-on', 'heartbeat', 'disk-activity', 'disk-read', 'disk-write', 'timer', 'pattern', 'audio-micmute', 'audio-mute', 'bluetooth-power', 'flash', 'kbd-capslock', 'mtd', 'nand-disk', 'none', 'torch', 'usb-gadget', 'usb-host', 'usbport']
   	'stmmac-0:01:link' does not match '^cpu[0-9]*$'
   	'stmmac-0:01:link' does not match '^hci[0-9]+-power$'
   	'stmmac-0:01:link' does not match '^mmc[0-9]+$'
   	'stmmac-0:01:link' does not match '^phy[0-9]+tx$'
   	from schema $id: http://devicetree.org/schemas/leds/leds-gpio.yaml#
>> arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6c.dtb: leds: led-1: Unevaluated properties are not allowed ('linux,default-trigger' was unexpected)

from schema $id: http://devicetree.org/schemas/leds/leds-gpio.yaml#
arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6c.dtb: leds: led-2:linux,default-trigger: 'oneOf' conditional failed, one must be fixed:
'r8169-3-3100:00:link' is not one of ['backlight', 'default-on', 'heartbeat', 'disk-activity', 'disk-read', 'disk-write', 'timer', 'pattern', 'audio-micmute', 'audio-mute', 'bluetooth-power', 'flash', 'kbd-capslock', 'mtd', 'nand-disk', 'none', 'torch', 'usb-gadget', 'usb-host', 'usbport'] 'r8169-3-3100:00:link' does not match '^cpu[0-9]*$'
'r8169-3-3100:00:link' does not match '^hci[0-9]+-power$'
'r8169-3-3100:00:link' does not match '^mmc[0-9]+$'
'r8169-3-3100:00:link' does not match '^phy[0-9]+tx$'
from schema $id: http://devicetree.org/schemas/leds/leds-gpio.yaml#
arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6c.dtb: leds: led-2: Unevaluated properties are not allowed ('linux,default-trigger' was unexpected)
from schema $id: http://devicetree.org/schemas/leds/leds-gpio.yaml#

Signature · 2 lines
0-DAY CI Kernel Test Service
https://github.com/intel/lkp-tests/wiki
maintainer
#8 lore raw

Re: [PATCH 3/5] arm64: dts: rockchip: Improve LEDs on NanoPi R6C/R6S

In reply to Sebastian Kropatsch

Am Mittwoch, 12. Juni 2024, 22:48:12 CEST schrieb Sebastian Kropatsch:

Quoted 9 lines

Move led-3 node into NanoPi R6C/R6S's source files since they have different functionalities on each board: On the R6S this LED is used to signal LAN2 link up, while on the R6C this LED does not have a pre-defined purpose.

In addition to that:
- Remove deprecated label property
- Add color and function properties
- Add linux,default-trigger to trigger on Ethernet link

Again, please don't group unrelated changes together into one patch. It makes things hard to read and hard to follow the changes.

Quoted 4 lines

---

Quoted 11 lines

DT validation doesn't like the 'linux,default-trigger = "stmmac-0:01:link"' properties, since "*:link" is not a valid value according to [Documentation/devicetree/bindings/leds/common.yaml]. These LEDs do have the specific purpose to show if an Ethernet link is up though. There is one LED for each Ethernet port and they are labeled WAN and LAN.
Using the 'linux,default-trigger' like this does work perfectly fine with this solution. I could not find another way to achieve this. Please let me know if there is a better way.
Maybe it would also be valid to add an entry to the DT bindings file to allow "*:link" as a value for 'linux,default-trigger'?

correct. If needed, things should be added to binding.

Heiko

#9 lore raw

Re: [PATCH 3/5] arm64: dts: rockchip: Improve LEDs on NanoPi R6C/R6S

Am 20.06.2024 um 20:42 schrieb Heiko Stübner:

Quoted 13 lines

Am Mittwoch, 12. Juni 2024, 22:48:12 CEST schrieb Sebastian Kropatsch:

Quoted 11 lines

DT validation doesn't like the 'linux,default-trigger = "stmmac-0:01:link"' properties, since "*:link" is not a valid value according to [Documentation/devicetree/bindings/leds/common.yaml]. These LEDs do have the specific purpose to show if an Ethernet link is up though. There is one LED for each Ethernet port and they are labeled WAN and LAN.
Using the 'linux,default-trigger' like this does work perfectly fine with this solution. I could not find another way to achieve this. Please let me know if there is a better way.
Maybe it would also be valid to add an entry to the DT bindings file to allow "*:link" as a value for 'linux,default-trigger'?

Quoted 1 line

correct. If needed, things should be added to binding.

Alright, I'll add this to the binding at [Documentation/devicetree/bindings/leds/common.yaml]

Should this be a completely separate patch or is it preferred to add a patch to this NanoPi patch series?

Cheers,
Sebastian

#10 lore raw

PATCH 4/5 arm64: dts: rockchip: Enable lower USB3 port on NanoPi R6C/R6S

In reply to Sebastian Kropatsch

Enable support for the lower USB 3.0 Type-A port on the NanoPi R6C and NanoPi R6S. The upper USB 2.0 Type-A port is already supported.

---
 .../boot/dts/rockchip/rk3588s-nanopi-r6.dtsi  | 28 +++++++++++++++++++
 1 file changed, 28 insertions(+)
arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi +28 -0
index 69d0f1f2349b..9676e7194451 100644
@@ -740,6 +740,17 @@ &tsadc {
 	status = "okay";
 };
 
+/* USB2 PHY for USB 3.0 Type-A (lower port)*/
+&u2phy0 {
+	status = "okay";
+};
+
+&u2phy0_otg {
+	phy-supply = <&vcc5v0_usb_otg0>;
+	status = "okay";
+};
+
+/* USB2 PHY for USB 2.0 Type-A (upper port)*/
 &u2phy2 {
 	status = "okay";
 };
@@ -755,10 +766,27 @@ &uart2 {
 	status = "okay";
 };
 
+/* USB 2.0 Type-A (upper port) */
+/* PHY: <&u2phy2_host> */
 &usb_host0_ehci {
 	status = "okay";
 };
 
+/* USB 2.0 Type-A (upper port) */
+/* PHY: <&u2phy2_host> */
 &usb_host0_ohci {
 	status = "okay";
 };
+
+/* USB 3.0 Type-A (lower port) */
+/* PHYs: <&u2phy0_otg>, <&usbdp_phy0> */
+&usb_host0_xhci {
+	dr_mode = "host";
+	extcon = <&u2phy0>;
+	status = "okay";
+};
+
+/* USB3 PHY for USB 3.0 Type-A (lower port)*/
+&usbdp_phy0 {
+	status = "okay";
+};
Signature · 1 line
2.43.0
#11 lore raw

PATCH 5/5 arm64: dts: rockchip: Enable GPU on NanoPi R6C/R6S

In reply to Sebastian Kropatsch

Enable the Mali GPU on the FriendlyElec NanoPi R6C and R6S.

---
 arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi | 6 ++++++
 1 file changed, 6 insertions(+)
arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi +6 -0
index 9676e7194451..3620677dc7b4 100644
@@ -207,6 +207,12 @@ &gmac1_rgmii_clk
 	status = "okay";
 };
 
+&gpu {
+	mali-supply = <&vdd_gpu_s0>;
+	sram-supply = <&vdd_gpu_mem_s0>;
+	status = "okay";
+};
+
 &i2c0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c0m2_xfer>;
Signature · 1 line
2.43.0
#12 lore raw
In reply to Sebastian Kropatsch
Quoted 28 lines · Sebastian Kropatsch

Hello,

This patch series fixes a lot of minor issues in the current devicetree for the FriendlyElec NanoPi R6 series (R6C and R6S), as well as adding support for the GPU and one USB3 port which was previously disabled.

To aid with these patches, I have refactored the devicetrees in such a way that they will now share a common dtsi source file in a similar fashion than what the NanoPi R5C and R5S are already doing. This makes changes which only affect one of the boards easier, less error-prone and more maintainable. Also we don't need to work with /delete-node/ and /delete-property/ this way :)

Cheers,
Sebastian

PS: Additional comments in patch 2 and 3.

---

Sebastian Kropatsch (5):
arm64: dts: rockchip: Add common definitions for NanoPi R6C and R6S
arm64: dts: rockchip: Fix regulators, gmac and naming on NanoPi

    R6C/R6S

arm64: dts: rockchip: Improve LEDs on NanoPi R6C/R6S
arm64: dts: rockchip: Enable lower USB3 port on NanoPi R6C/R6S
arm64: dts: rockchip: Enable GPU on NanoPi R6C/R6S

Quoted 11 lines
 ...-nanopi-r6s.dts => rk3588s-nanopi-r6.dtsi} | 242 +++---
 .../boot/dts/rockchip/rk3588s-nanopi-r6c.dts  |  48 +-
 .../boot/dts/rockchip/rk3588s-nanopi-r6s.dts  | 743 +-----------------
 3 files changed, 193 insertions(+), 840 deletions(-)
 copy arch/arm64/boot/dts/rockchip/{rk3588s-nanopi-r6s.dts => rk3588s-nanopi-r6.dtsi} (81%)

--
2.43.0

My bot found new DTB warnings on the .dts files added or changed in this series.

Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings are fixed by another series. Ultimately, it is up to the platform maintainer whether these warnings are acceptable or not. No need to reply unless the platform maintainer has comments.

If you already ran DT checks and didn't see these error(s), then make sure dt-schema is up to date:

  pip3 install dtschema --upgrade

New warnings running 'make CHECK_DTBS=y rockchip/rk3588s-nanopi-r6c.dtb rockchip/rk3588s-nanopi-r6s.dtb' for [email protected]:

arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6c.dtb: leds: led-1:linux,default-trigger: 'oneOf' conditional failed, one must be fixed:

	'stmmac-0:01:link' is not one of ['backlight', 'default-on', 'heartbeat', 'disk-activity', 'disk-read', 'disk-write', 'timer', 'pattern', 'audio-micmute', 'audio-mute', 'bluetooth-power', 'flash', 'kbd-capslock', 'mtd', 'nand-disk', 'none', 'torch', 'usb-gadget', 'usb-host', 'usbport']
	'stmmac-0:01:link' does not match '^cpu[0-9]*$'
	'stmmac-0:01:link' does not match '^hci[0-9]+-power$'
	'stmmac-0:01:link' does not match '^mmc[0-9]+$'
	'stmmac-0:01:link' does not match '^phy[0-9]+tx$'
	from schema $id: http://devicetree.org/schemas/leds/leds-gpio.yaml#
arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6c.dtb: leds: led-1: Unevaluated properties are not allowed ('linux,default-trigger' was unexpected)
	from schema $id: http://devicetree.org/schemas/leds/leds-gpio.yaml#
arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6c.dtb: leds: led-2:linux,default-trigger: 'oneOf' conditional failed, one must be fixed:
	'r8169-3-3100:00:link' is not one of ['backlight', 'default-on', 'heartbeat', 'disk-activity', 'disk-read', 'disk-write', 'timer', 'pattern', 'audio-micmute', 'audio-mute', 'bluetooth-power', 'flash', 'kbd-capslock', 'mtd', 'nand-disk', 'none', 'torch', 'usb-gadget', 'usb-host', 'usbport']
	'r8169-3-3100:00:link' does not match '^cpu[0-9]*$'
	'r8169-3-3100:00:link' does not match '^hci[0-9]+-power$'
	'r8169-3-3100:00:link' does not match '^mmc[0-9]+$'
	'r8169-3-3100:00:link' does not match '^phy[0-9]+tx$'
	from schema $id: http://devicetree.org/schemas/leds/leds-gpio.yaml#
arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6c.dtb: leds: led-2: Unevaluated properties are not allowed ('linux,default-trigger' was unexpected)
	from schema $id: http://devicetree.org/schemas/leds/leds-gpio.yaml#
arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6s.dtb: leds: led-1:linux,default-trigger: 'oneOf' conditional failed, one must be fixed:
	'stmmac-0:01:link' is not one of ['backlight', 'default-on', 'heartbeat', 'disk-activity', 'disk-read', 'disk-write', 'timer', 'pattern', 'audio-micmute', 'audio-mute', 'bluetooth-power', 'flash', 'kbd-capslock', 'mtd', 'nand-disk', 'none', 'torch', 'usb-gadget', 'usb-host', 'usbport']
	'stmmac-0:01:link' does not match '^cpu[0-9]*$'
	'stmmac-0:01:link' does not match '^hci[0-9]+-power$'
	'stmmac-0:01:link' does not match '^mmc[0-9]+$'
	'stmmac-0:01:link' does not match '^phy[0-9]+tx$'
	from schema $id: http://devicetree.org/schemas/leds/leds-gpio.yaml#
arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6s.dtb: leds: led-1: Unevaluated properties are not allowed ('linux,default-trigger' was unexpected)
	from schema $id: http://devicetree.org/schemas/leds/leds-gpio.yaml#
arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6s.dtb: leds: led-2:linux,default-trigger: 'oneOf' conditional failed, one must be fixed:
	'r8169-3-3100:00:link' is not one of ['backlight', 'default-on', 'heartbeat', 'disk-activity', 'disk-read', 'disk-write', 'timer', 'pattern', 'audio-micmute', 'audio-mute', 'bluetooth-power', 'flash', 'kbd-capslock', 'mtd', 'nand-disk', 'none', 'torch', 'usb-gadget', 'usb-host', 'usbport']
	'r8169-3-3100:00:link' does not match '^cpu[0-9]*$'
	'r8169-3-3100:00:link' does not match '^hci[0-9]+-power$'
	'r8169-3-3100:00:link' does not match '^mmc[0-9]+$'
	'r8169-3-3100:00:link' does not match '^phy[0-9]+tx$'
	from schema $id: http://devicetree.org/schemas/leds/leds-gpio.yaml#
arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6s.dtb: leds: led-2: Unevaluated properties are not allowed ('linux,default-trigger' was unexpected)
	from schema $id: http://devicetree.org/schemas/leds/leds-gpio.yaml#
arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6s.dtb: leds: led-3:linux,default-trigger: 'oneOf' conditional failed, one must be fixed:
	'r8169-4-4100:00:link' is not one of ['backlight', 'default-on', 'heartbeat', 'disk-activity', 'disk-read', 'disk-write', 'timer', 'pattern', 'audio-micmute', 'audio-mute', 'bluetooth-power', 'flash', 'kbd-capslock', 'mtd', 'nand-disk', 'none', 'torch', 'usb-gadget', 'usb-host', 'usbport']
	'r8169-4-4100:00:link' does not match '^cpu[0-9]*$'
	'r8169-4-4100:00:link' does not match '^hci[0-9]+-power$'
	'r8169-4-4100:00:link' does not match '^mmc[0-9]+$'
	'r8169-4-4100:00:link' does not match '^phy[0-9]+tx$'
	from schema $id: http://devicetree.org/schemas/leds/leds-gpio.yaml#

arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6s.dtb: leds: led-3: Unevaluated properties are not allowed ('linux,default-trigger' was unexpected)
from schema $id: http://devicetree.org/schemas/leds/leds-gpio.yaml#