Skip to contentSkip to conversation

Add ability to flash modules' firmware

PATCH Superseded Danielle Ratson 4 participants 13 messages Jun 19, 2024 – Jun 21, 2024

Subsystems (7)

v6 of 8 Superseded Latest is v8 →

lore
Share & tools
lore
#0 lore raw

v6 cover Add ability to flash modules' firmware

CMIS compliant modules such as QSFP-DD might be running a firmware that can be updated in a vendor-neutral way by exchanging messages between the host and the module as described in section 7.2.2 of revision 4.0 of the CMIS standard.

According to the CMIS standard, the firmware update process is done using a CDB commands sequence.

CDB (Command Data Block Message Communication) reads and writes are performed on memory map pages 9Fh-AFh according to the CMIS standard, section 8.12 of revision 4.0.

Add a pair of new ethtool messages that allow:

* User space to trigger firmware update of transceiver modules

* The kernel to notify user space about the progress of the process

The user interface is designed to be asynchronous in order to avoid RTNL being held for too long and to allow several modules to be updated simultaneously. The interface is designed with CMIS compliant modules in mind, but kept generic enough to accommodate future use cases, if these arise.

The kernel interface that will implement the firmware update using CDB command will include 2 layers that will be added under ethtool:

* The upper layer that will be triggered from the module layer, is cmis_ fw_update.
* The lower one is cmis_cdb.

In the future there might be more operations to implement using CDB commands. Therefore, the idea is to keep the cmis_cdb interface clean and the cmis_fw_update specific to the cdb commands handling it.

The communication between the kernel and the driver will be done using two ethtool operations that enable reading and writing the transceiver module EEPROM.
The operation ethtool_ops::get_module_eeprom_by_page, that is already implemented, will be used for reading from the EEPROM the CDB reply, e.g. reading module setting, state, etc.
The operation ethtool_ops::set_module_eeprom_by_page, that is added in the current patchset, will be used for writing to the EEPROM the CDB command such as start firmware image, run firmware image, etc.

Therefore in order for a driver to implement module flashing, that driver needs to implement the two functions mentioned above.

Patchset overview:
Patch #1-#2: Implement the EEPROM writing in mlxsw. Patch #3: Define the interface between the kernel and user space. Patch #4: Add ability to notify the flashing firmware progress. Patch #5: Veto operations during flashing.
Patch #6: Add extended compliance codes.
Patch #7: Add the cdb layer.
Patch #8: Add the fw_update layer.
Patch #9: Add ability to flash transceiver modules' firmware.

v6:
* Squash some of the last patch to patch #5 and patch #9.
Patch #3:
* Add paragraph in .rst file.
Patch #4:
* Reserve '1' more place on SKB for NUL terminator in
the error message string.
* Add more prints on error flow, re-write the printing function and add ethnl_module_fw_flash_ntf_put_err().
* Change the communication method so notification will be sent in unicast instead of multicast.
* Add new 'struct ethnl_module_fw_flash_ntf_params' that holds the relevant info for unicast communication and use it to send notification to the specific socket.
* s/nla_put_u64_64bit/nla_put_uint/
Patch #7:
* In ethtool_cmis_cdb_init(), Use 'const' for the 'params' parameter.
Patch #8:
* Add a list field to struct ethtool_module_fw_flash for module_fw_flash_work_list that will be presented in the next patch.
* Move ethtool_cmis_fw_update() cleaning to a new function that will be represented in the next patch.
* Move some of the fields in struct ethtool_module_fw_flash to a separate struct, so ethtool_cmis_fw_update() will get only the relevant parameters for it.
* Edit the relevant functions to get the relevant params for them.
* s/CMIS_MODULE_READY_MAX_DURATION_USEC/CMIS_MODULE_READY_MAX_DURATION_MSEC
Patch #9:
* Add a paragraph in the commit message.
* Rename labels in module_flash_fw_schedule().
* Add info to genl_sk_priv_*() and implement the relevant callbacks, in order to handle properly a scenario of closing the socket from user space before the work item was ended.
* Add a list the holds all the ethtool_module_fw_flash struct that corresponds to the in progress work items.
* Add a new enum for the socket types.
* Use both above to identify a flashing socket, add it to the list and when closing socket affect only the flashing type.
* Create a new function that will get the work item instead of ethtool_cmis_fw_update().
* Edit the relevant functions to get the relevant params for them.
* The new function will call the old ethtool_cmis_fw_update(), and do the cleaning, so the existence of the list should be completely isolated in module.c.

Danielle Ratson (7):
ethtool: Add an interface for flashing transceiver modules' firmware
ethtool: Add flashing transceiver modules' firmware notifications
ability
ethtool: Veto some operations during firmware flashing process
net: sfp: Add more extended compliance codes
ethtool: cmis_cdb: Add a layer for supporting CDB commands
ethtool: cmis_fw_update: add a layer for supporting firmware update
using CDB
ethtool: Add ability to flash transceiver modules' firmware

Ido Schimmel (2):
ethtool: Add ethtool operation to write to a transceiver module EEPROM
mlxsw: Implement ethtool operation to write to a transceiver module
EEPROM

 Documentation/netlink/specs/ethtool.yaml      |  55 ++
 Documentation/networking/ethtool-netlink.rst  |  70 +++
 .../net/ethernet/mellanox/mlxsw/core_env.c    |  57 ++
 .../net/ethernet/mellanox/mlxsw/core_env.h    |   6 +
 drivers/net/ethernet/mellanox/mlxsw/minimal.c |  15 +
 .../mellanox/mlxsw/spectrum_ethtool.c         |  15 +
 include/linux/ethtool.h                       |  20 +-
 include/linux/netdevice.h                     |   4 +-
 include/linux/sfp.h                           |   6 +
 include/uapi/linux/ethtool.h                  |  18 +
 include/uapi/linux/ethtool_netlink.h          |  19 +
 net/ethtool/Makefile                          |   2 +-
 net/ethtool/cmis.h                            | 124 ++++
 net/ethtool/cmis_cdb.c                        | 581 ++++++++++++++++++
 net/ethtool/cmis_fw_update.c                  | 399 ++++++++++++
 net/ethtool/eeprom.c                          |   6 +
 net/ethtool/ioctl.c                           |  12 +
 net/ethtool/module.c                          | 392 ++++++++++++
 net/ethtool/module_fw.h                       |  75 +++
 net/ethtool/netlink.c                         |  55 ++
 net/ethtool/netlink.h                         |  16 +
 tools/net/ynl/Makefile.deps                   |   3 +-
 22 files changed, 1939 insertions(+), 11 deletions(-)
 create mode 100644 net/ethtool/cmis.h
 create mode 100644 net/ethtool/cmis_cdb.c
 create mode 100644 net/ethtool/cmis_fw_update.c
 create mode 100644 net/ethtool/module_fw.h
Signature · 1 line
2.45.0
#1 lore raw

PATCH v6 1/9 ethtool: Add ethtool operation to write to a transceiver module EEPROM

From: Ido Schimmel <[email protected]>

Ethtool can already retrieve information from a transceiver module EEPROM by invoking the ethtool_ops::get_module_eeprom_by_page operation. Add a corresponding operation that allows ethtool to write to a transceiver module EEPROM.

The new write operation is purely an in-kernel API and is not exposed to user space.

The purpose of this operation is not to enable arbitrary read / write access, but to allow the kernel to write to specific addresses as part of transceiver module firmware flashing. In the future, more functionality can be implemented on top of these read / write operations.

Adjust the comments of the 'ethtool_module_eeprom' structure as it is no longer used only for read access.

---
 include/linux/ethtool.h | 20 ++++++++++++--------
 1 file changed, 12 insertions(+), 8 deletions(-)
include/linux/ethtool.h +12 -8
index 6fd9107d3cc0..fa1a5d0e3213 100644
@@ -504,17 +504,16 @@ struct ethtool_ts_stats {
 #define ETH_MODULE_MAX_I2C_ADDRESS	0x7f
 
 /**
- * struct ethtool_module_eeprom - EEPROM dump from specified page
- * @offset: Offset within the specified EEPROM page to begin read, in bytes.
- * @length: Number of bytes to read.
- * @page: Page number to read from.
- * @bank: Page bank number to read from, if applicable by EEPROM spec.
+ * struct ethtool_module_eeprom - plug-in module EEPROM read / write parameters
+ * @offset: When @offset is 0-127, it is used as an address to the Lower Memory
+ *	(@page must be 0). Otherwise, it is used as an address to the
+ *	Upper Memory.
+ * @length: Number of bytes to read / write.
+ * @page: Page number.
+ * @bank: Bank number, if supported by EEPROM spec.
  * @i2c_address: I2C address of a page. Value less than 0x7f expected. Most
  *	EEPROMs use 0x50 or 0x51.
  * @data: Pointer to buffer with EEPROM data of @length size.
- *
- * This can be used to manage pages during EEPROM dump in ethtool and pass
- * required information to the driver.
  */
 struct ethtool_module_eeprom {
 	u32	offset;
@@ -822,6 +821,8 @@ struct ethtool_rxfh_param {
  * @get_module_eeprom_by_page: Get a region of plug-in module EEPROM data from
  *	specified page. Returns a negative error code or the amount of bytes
  *	read.
+ * @set_module_eeprom_by_page: Write to a region of plug-in module EEPROM,
+ *	from kernel space only. Returns a negative error code or zero.
  * @get_eth_phy_stats: Query some of the IEEE 802.3 PHY statistics.
  * @get_eth_mac_stats: Query some of the IEEE 802.3 MAC statistics.
  * @get_eth_ctrl_stats: Query some of the IEEE 802.3 MAC Ctrl statistics.
@@ -956,6 +957,9 @@ struct ethtool_ops {
 	int	(*get_module_eeprom_by_page)(struct net_device *dev,
 					     const struct ethtool_module_eeprom *page,
 					     struct netlink_ext_ack *extack);
+	int	(*set_module_eeprom_by_page)(struct net_device *dev,
+					     const struct ethtool_module_eeprom *page,
+					     struct netlink_ext_ack *extack);
 	void	(*get_eth_phy_stats)(struct net_device *dev,
 				     struct ethtool_eth_phy_stats *phy_stats);
 	void	(*get_eth_mac_stats)(struct net_device *dev,
Signature · 1 line
2.45.0
#2 lore raw

PATCH v6 2/9 mlxsw: Implement ethtool operation to write to a transceiver module EEPROM

In reply to Danielle Ratson

From: Ido Schimmel <[email protected]>

Implement the ethtool_ops::set_module_eeprom_by_page operation to allow ethtool to write to a transceiver module EEPROM, in a similar fashion to the ethtool_ops::get_module_eeprom_by_page operation.

---
 .../net/ethernet/mellanox/mlxsw/core_env.c    | 57 +++++++++++++++++++
 .../net/ethernet/mellanox/mlxsw/core_env.h    |  6 ++
 drivers/net/ethernet/mellanox/mlxsw/minimal.c | 15 +++++
 .../mellanox/mlxsw/spectrum_ethtool.c         | 15 +++++
 4 files changed, 93 insertions(+)
drivers/net/ethernet/mellanox/mlxsw/core_env.c +57 -0
index 6c06b0592760..294e758f1067 100644
@@ -513,6 +513,63 @@ mlxsw_env_get_module_eeprom_by_page(struct mlxsw_core *mlxsw_core,
 }
 EXPORT_SYMBOL(mlxsw_env_get_module_eeprom_by_page);
 
+int
+mlxsw_env_set_module_eeprom_by_page(struct mlxsw_core *mlxsw_core,
+				    u8 slot_index, u8 module,
+				    const struct ethtool_module_eeprom *page,
+				    struct netlink_ext_ack *extack)
+{
+	struct mlxsw_env *mlxsw_env = mlxsw_core_env(mlxsw_core);
+	u32 bytes_written = 0;
+	u16 device_addr;
+	int err;
+
+	if (!mlxsw_env_linecard_is_active(mlxsw_env, slot_index)) {
+		NL_SET_ERR_MSG_MOD(extack,
+				   "Cannot write to EEPROM of a module on an inactive line card");
+		return -EIO;
+	}
+
+	err = mlxsw_env_validate_module_type(mlxsw_core, slot_index, module);
+	if (err) {
+		NL_SET_ERR_MSG_MOD(extack, "EEPROM is not equipped on port module type");
+		return err;
+	}
+
+	device_addr = page->offset;
+
+	while (bytes_written < page->length) {
+		char mcia_pl[MLXSW_REG_MCIA_LEN];
+		char eeprom_tmp[128] = {};
+		u8 size;
+
+		size = min_t(u8, page->length - bytes_written,
+			     mlxsw_env->max_eeprom_len);
+
+		mlxsw_reg_mcia_pack(mcia_pl, slot_index, module, page->page,
+				    device_addr + bytes_written, size,
+				    page->i2c_address);
+		mlxsw_reg_mcia_bank_number_set(mcia_pl, page->bank);
+		memcpy(eeprom_tmp, page->data + bytes_written, size);
+		mlxsw_reg_mcia_eeprom_memcpy_to(mcia_pl, eeprom_tmp);
+
+		err = mlxsw_reg_write(mlxsw_core, MLXSW_REG(mcia), mcia_pl);
+		if (err) {
+			NL_SET_ERR_MSG_MOD(extack, "Failed to access module's EEPROM");
+			return err;
+		}
+
+		err = mlxsw_env_mcia_status_process(mcia_pl, extack);
+		if (err)
+			return err;
+
+		bytes_written += size;
+	}
+
+	return 0;
+}
+EXPORT_SYMBOL(mlxsw_env_set_module_eeprom_by_page);
+
 static int mlxsw_env_module_reset(struct mlxsw_core *mlxsw_core, u8 slot_index,
 				  u8 module)
 {
drivers/net/ethernet/mellanox/mlxsw/core_env.h +6 -0
index a197e3ae069c..e4ff17869400 100644
@@ -28,6 +28,12 @@ mlxsw_env_get_module_eeprom_by_page(struct mlxsw_core *mlxsw_core,
 				    const struct ethtool_module_eeprom *page,
 				    struct netlink_ext_ack *extack);
 
+int
+mlxsw_env_set_module_eeprom_by_page(struct mlxsw_core *mlxsw_core,
+				    u8 slot_index, u8 module,
+				    const struct ethtool_module_eeprom *page,
+				    struct netlink_ext_ack *extack);
+
 int mlxsw_env_reset_module(struct net_device *netdev,
 			   struct mlxsw_core *mlxsw_core, u8 slot_index,
 			   u8 module, u32 *flags);
drivers/net/ethernet/mellanox/mlxsw/minimal.c +15 -0
index f0ceb196a6ce..448263423e36 100644
@@ -140,6 +140,20 @@ mlxsw_m_get_module_eeprom_by_page(struct net_device *netdev,
 						   page, extack);
 }
 
+static int
+mlxsw_m_set_module_eeprom_by_page(struct net_device *netdev,
+				  const struct ethtool_module_eeprom *page,
+				  struct netlink_ext_ack *extack)
+{
+	struct mlxsw_m_port *mlxsw_m_port = netdev_priv(netdev);
+	struct mlxsw_core *core = mlxsw_m_port->mlxsw_m->core;
+
+	return mlxsw_env_set_module_eeprom_by_page(core,
+						   mlxsw_m_port->slot_index,
+						   mlxsw_m_port->module,
+						   page, extack);
+}
+
 static int mlxsw_m_reset(struct net_device *netdev, u32 *flags)
 {
 	struct mlxsw_m_port *mlxsw_m_port = netdev_priv(netdev);
@@ -181,6 +195,7 @@ static const struct ethtool_ops mlxsw_m_port_ethtool_ops = {
 	.get_module_info	= mlxsw_m_get_module_info,
 	.get_module_eeprom	= mlxsw_m_get_module_eeprom,
 	.get_module_eeprom_by_page = mlxsw_m_get_module_eeprom_by_page,
+	.set_module_eeprom_by_page = mlxsw_m_set_module_eeprom_by_page,
 	.reset			= mlxsw_m_reset,
 	.get_module_power_mode	= mlxsw_m_get_module_power_mode,
 	.set_module_power_mode	= mlxsw_m_set_module_power_mode,
drivers/net/ethernet/mellanox/mlxsw/spectrum_ethtool.c +15 -0
index a755b0a901d3..c79da1411d33 100644
@@ -1067,6 +1067,20 @@ mlxsw_sp_get_module_eeprom_by_page(struct net_device *dev,
 						   module, page, extack);
 }
 
+static int
+mlxsw_sp_set_module_eeprom_by_page(struct net_device *dev,
+				   const struct ethtool_module_eeprom *page,
+				   struct netlink_ext_ack *extack)
+{
+	struct mlxsw_sp_port *mlxsw_sp_port = netdev_priv(dev);
+	struct mlxsw_sp *mlxsw_sp = mlxsw_sp_port->mlxsw_sp;
+	u8 slot_index = mlxsw_sp_port->mapping.slot_index;
+	u8 module = mlxsw_sp_port->mapping.module;
+
+	return mlxsw_env_set_module_eeprom_by_page(mlxsw_sp->core, slot_index,
+						   module, page, extack);
+}
+
 static int
 mlxsw_sp_get_ts_info(struct net_device *netdev, struct ethtool_ts_info *info)
 {
@@ -1256,6 +1270,7 @@ const struct ethtool_ops mlxsw_sp_port_ethtool_ops = {
 	.get_module_info		= mlxsw_sp_get_module_info,
 	.get_module_eeprom		= mlxsw_sp_get_module_eeprom,
 	.get_module_eeprom_by_page	= mlxsw_sp_get_module_eeprom_by_page,
+	.set_module_eeprom_by_page	= mlxsw_sp_set_module_eeprom_by_page,
 	.get_ts_info			= mlxsw_sp_get_ts_info,
 	.get_eth_phy_stats		= mlxsw_sp_get_eth_phy_stats,
 	.get_eth_mac_stats		= mlxsw_sp_get_eth_mac_stats,
Signature · 1 line
2.45.0
#3 lore raw

PATCH v6 3/9 ethtool: Add an interface for flashing transceiver modules' firmware

In reply to Danielle Ratson

CMIS compliant modules such as QSFP-DD might be running a firmware that can be updated in a vendor-neutral way by exchanging messages between the host and the module as described in section 7.3.1 of revision 5.2 of the CMIS standard.

Add a pair of new ethtool messages that allow:

* User space to trigger firmware update of transceiver modules

* The kernel to notify user space about the progress of the process

The user interface is designed to be asynchronous in order to avoid RTNL being held for too long and to allow several modules to be updated simultaneously. The interface is designed with CMIS compliant modules in mind, but kept generic enough to accommodate future use cases, if these arise.

---

Notes:
v6:
* Add paragraph in .rst file.

v5:
* Modify tools/net/ynl/Makefile.deps so the ynl file will include the ethtool.h changes.
* u64>uint for 'total' and 'done' attrs.
* Translate the enum from ethtool_netlink.h to YAML.

v4:
* s/is composed from/consists of/.

 Documentation/netlink/specs/ethtool.yaml     | 55 +++++++++++++++
 Documentation/networking/ethtool-netlink.rst | 70 ++++++++++++++++++++
 include/uapi/linux/ethtool.h                 | 18 +++++
 include/uapi/linux/ethtool_netlink.h         | 19 ++++++
 tools/net/ynl/Makefile.deps                  |  3 +-
 5 files changed, 164 insertions(+), 1 deletion(-)
Documentation/netlink/specs/ethtool.yaml +55 -0
index 00dc61358be8..43c5f21e6096 100644
@@ -20,6 +20,10 @@ definitions:
     name: header-flags
     type: flags
     entries: [ compact-bitsets, omit-reply, stats ]
+  -
+    name: module-fw-flash-status
+    type: enum
+    entries: [ started, in_progress, completed, error ]
 
 attribute-sets:
   -
@@ -975,6 +979,32 @@ attribute-sets:
       -
         name: burst-tmr
         type: u32
+  -
+    name: module-fw-flash
+    attributes:
+      -
+        name: header
+        type: nest
+        nested-attributes: header
+      -
+        name: file-name
+        type: string
+      -
+        name: password
+        type: u32
+      -
+        name: status
+        type: u32
+        enum: module-fw-flash-status
+      -
+        name: status-msg
+        type: string
+      -
+        name: done
+        type: uint
+      -
+        name: total
+        type: uint
 
 operations:
   enum-model: directional
@@ -1730,3 +1760,28 @@ operations:
       name: mm-ntf
       doc: Notification for change in MAC Merge configuration.
       notify: mm-get
+    -
+      name: module-fw-flash-act
+      doc: Flash transceiver module firmware.
+
+      attribute-set: module-fw-flash
+
+      do:
+        request:
+          attributes:
+            - header
+            - file-name
+            - password
+    -
+      name: module-fw-flash-ntf
+      doc: Notification for firmware flashing progress and status.
+
+      attribute-set: module-fw-flash
+
+      event:
+        attributes:
+          - header
+          - status
+          - status-msg
+          - done
+          - total
Documentation/networking/ethtool-netlink.rst +70 -0

92 lines not on this page · raw message

include/uapi/linux/ethtool.h +18 -0
index 8733a3117902..e011384c915c 100644
@@ -877,6 +877,24 @@ enum ethtool_mm_verify_status {
 	ETHTOOL_MM_VERIFY_STATUS_DISABLED,
 };
 
+/**
+ * enum ethtool_module_fw_flash_status - plug-in module firmware flashing status
+ * @ETHTOOL_MODULE_FW_FLASH_STATUS_STARTED: The firmware flashing process has
+ *	started.
+ * @ETHTOOL_MODULE_FW_FLASH_STATUS_IN_PROGRESS: The firmware flashing process
+ *	is in progress.
+ * @ETHTOOL_MODULE_FW_FLASH_STATUS_COMPLETED: The firmware flashing process was
+ *	completed successfully.
+ * @ETHTOOL_MODULE_FW_FLASH_STATUS_ERROR: The firmware flashing process was
+ *	stopped due to an error.
+ */
+enum ethtool_module_fw_flash_status {
+	ETHTOOL_MODULE_FW_FLASH_STATUS_STARTED = 1,
+	ETHTOOL_MODULE_FW_FLASH_STATUS_IN_PROGRESS,
+	ETHTOOL_MODULE_FW_FLASH_STATUS_COMPLETED,
+	ETHTOOL_MODULE_FW_FLASH_STATUS_ERROR,
+};
+
 /**
  * struct ethtool_gstrings - string set for data tagging
  * @cmd: Command number = %ETHTOOL_GSTRINGS
include/uapi/linux/ethtool_netlink.h +19 -0
index b49b804b9495..3748f018b985 100644
@@ -57,6 +57,7 @@ enum {
 	ETHTOOL_MSG_PLCA_GET_STATUS,
 	ETHTOOL_MSG_MM_GET,
 	ETHTOOL_MSG_MM_SET,
+	ETHTOOL_MSG_MODULE_FW_FLASH_ACT,
 
 	/* add new constants above here */
 	__ETHTOOL_MSG_USER_CNT,
@@ -109,6 +110,7 @@ enum {
 	ETHTOOL_MSG_PLCA_NTF,
 	ETHTOOL_MSG_MM_GET_REPLY,
 	ETHTOOL_MSG_MM_NTF,
+	ETHTOOL_MSG_MODULE_FW_FLASH_NTF,
 
 	/* add new constants above here */
 	__ETHTOOL_MSG_KERNEL_CNT,
@@ -996,6 +998,23 @@ enum {
 	ETHTOOL_A_MM_MAX = (__ETHTOOL_A_MM_CNT - 1)
 };
 
+/* MODULE_FW_FLASH */
+
+enum {
+	ETHTOOL_A_MODULE_FW_FLASH_UNSPEC,
+	ETHTOOL_A_MODULE_FW_FLASH_HEADER,		/* nest - _A_HEADER_* */
+	ETHTOOL_A_MODULE_FW_FLASH_FILE_NAME,		/* string */
+	ETHTOOL_A_MODULE_FW_FLASH_PASSWORD,		/* u32 */
+	ETHTOOL_A_MODULE_FW_FLASH_STATUS,		/* u32 */
+	ETHTOOL_A_MODULE_FW_FLASH_STATUS_MSG,		/* string */
+	ETHTOOL_A_MODULE_FW_FLASH_DONE,			/* uint */
+	ETHTOOL_A_MODULE_FW_FLASH_TOTAL,		/* uint */
+
+	/* add new constants above here */
+	__ETHTOOL_A_MODULE_FW_FLASH_CNT,
+	ETHTOOL_A_MODULE_FW_FLASH_MAX = (__ETHTOOL_A_MODULE_FW_FLASH_CNT - 1)
+};
+
 /* generic netlink info */
 #define ETHTOOL_GENL_NAME "ethtool"
 #define ETHTOOL_GENL_VERSION 1
tools/net/ynl/Makefile.deps +2 -1
index f4e8eb79c1b8..dbdca32a1c61 100644
@@ -16,7 +16,8 @@ get_hdr_inc=-D$(1) -include $(UAPI_PATH)/linux/$(2)
 
 CFLAGS_devlink:=$(call get_hdr_inc,_LINUX_DEVLINK_H_,devlink.h)
 CFLAGS_dpll:=$(call get_hdr_inc,_LINUX_DPLL_H,dpll.h)
-CFLAGS_ethtool:=$(call get_hdr_inc,_LINUX_ETHTOOL_NETLINK_H_,ethtool_netlink.h)
+CFLAGS_ethtool:=$(call get_hdr_inc,_LINUX_ETHTOOL_H,ethtool.h) \
+		$(call get_hdr_inc,_LINUX_ETHTOOL_NETLINK_H_,ethtool_netlink.h)
 CFLAGS_handshake:=$(call get_hdr_inc,_LINUX_HANDSHAKE_H,handshake.h)
 CFLAGS_mptcp_pm:=$(call get_hdr_inc,_LINUX_MPTCP_PM_H,mptcp_pm.h)
 CFLAGS_netdev:=$(call get_hdr_inc,_LINUX_NETDEV_H,netdev.h)
Signature · 1 line
2.45.0
#4 lore raw

PATCH v6 4/9 ethtool: Add flashing transceiver modules' firmware notifications ability

In reply to Danielle Ratson

Add progress notifications ability to user space while flashing modules' firmware by implementing the interface between the user space and the kernel.

---

Notes:
v6:
* Reserve '1' more place on SKB for NUL terminator in the error message string.
* Add more prints on error flow, re-write the printing function and add ethnl_module_fw_flash_ntf_put_err().
* Change the communication method so notification will be sent in unicast instead of multicast.
* Add new 'struct ethnl_module_fw_flash_ntf_params' that holds the relevant info for unicast communication and use it to send notification to the specific socket.
* s/nla_put_u64_64bit/nla_put_uint/

v2:
* Increase err_msg length.

 net/ethtool/module.c    | 117 ++++++++++++++++++++++++++++++++++++++++
 net/ethtool/module_fw.h |  31 +++++++++++
 net/ethtool/netlink.c   |   5 ++
 net/ethtool/netlink.h   |   1 +
 4 files changed, 154 insertions(+)
 create mode 100644 net/ethtool/module_fw.h
net/ethtool/module.c +117 -0
index ceb575efc290..932415bd44c6 100644
@@ -5,6 +5,7 @@
 #include "netlink.h"
 #include "common.h"
 #include "bitset.h"
+#include "module_fw.h"
 
 struct module_req_info {
 	struct ethnl_req_info base;
@@ -158,3 +159,119 @@ const struct ethnl_request_ops ethnl_module_request_ops = {
 	.set			= ethnl_set_module,
 	.set_ntf_cmd		= ETHTOOL_MSG_MODULE_NTF,
 };
+
+/* MODULE_FW_FLASH_NTF */
+
+static int
+ethnl_module_fw_flash_ntf_put_err(struct sk_buff *skb, char *err_msg,
+				  char *sub_err_msg)
+{
+	int err_msg_len, sub_err_msg_len, total_len;
+	struct nlattr *attr;
+
+	if (!err_msg)
+		return 0;
+
+	err_msg_len = strlen(err_msg);
+	total_len = err_msg_len + 2; /* For period and NUL. */
+
+	if (sub_err_msg) {
+		sub_err_msg_len = strlen(sub_err_msg);
+		total_len += sub_err_msg_len + 2; /* For ", ". */
+	}
+
+	attr = nla_reserve(skb, ETHTOOL_A_MODULE_FW_FLASH_STATUS_MSG,
+			   total_len);
+	if (!attr)
+		return PTR_ERR(attr);
+
+	if (sub_err_msg)
+		sprintf(nla_data(attr), "%s, %s.", err_msg, sub_err_msg);
+	else
+		sprintf(nla_data(attr), "%s.", err_msg);
+
+	return 0;
+}
+
+static void
+ethnl_module_fw_flash_ntf(struct net_device *dev,
+			  enum ethtool_module_fw_flash_status status,
+			  struct ethnl_module_fw_flash_ntf_params *ntf_params,
+			  char *err_msg, char *sub_err_msg,
+			  u64 done, u64 total)
+{
+	struct sk_buff *skb;
+	void *hdr;
+	int ret;
+
+	if (ntf_params->closed_sock)
+		return;
+
+	skb = genlmsg_new(NLMSG_GOODSIZE, GFP_KERNEL);
+	if (!skb)
+		return;
+
+	hdr = ethnl_unicast_put(skb, ntf_params->portid, ntf_params->seq,
+				ETHTOOL_MSG_MODULE_FW_FLASH_NTF);
+	if (!hdr)
+		goto err_skb;
+
+	ret = ethnl_fill_reply_header(skb, dev,
+				      ETHTOOL_A_MODULE_FW_FLASH_HEADER);
+	if (ret < 0)
+		goto err_skb;
+
+	if (nla_put_u32(skb, ETHTOOL_A_MODULE_FW_FLASH_STATUS, status))
+		goto err_skb;
+
+	ret = ethnl_module_fw_flash_ntf_put_err(skb, err_msg, sub_err_msg);
+	if (ret < 0)
+		goto err_skb;
+
+	if (nla_put_uint(skb, ETHTOOL_A_MODULE_FW_FLASH_DONE, done))
+		goto err_skb;
+
+	if (nla_put_uint(skb, ETHTOOL_A_MODULE_FW_FLASH_TOTAL, total))
+		goto err_skb;
+
+	genlmsg_end(skb, hdr);
+	genlmsg_unicast(dev_net(dev), skb, ntf_params->portid);
+	return;
+
+err_skb:
+	nlmsg_free(skb);
+}
+
+void ethnl_module_fw_flash_ntf_err(struct net_device *dev,
+				   struct ethnl_module_fw_flash_ntf_params *params,
+				   char *err_msg, char *sub_err_msg)
+{
+	ethnl_module_fw_flash_ntf(dev, ETHTOOL_MODULE_FW_FLASH_STATUS_ERROR,
+				  params, err_msg, sub_err_msg, 0, 0);
+}
+
+void
+ethnl_module_fw_flash_ntf_start(struct net_device *dev,
+				struct ethnl_module_fw_flash_ntf_params *params)
+{
+	ethnl_module_fw_flash_ntf(dev, ETHTOOL_MODULE_FW_FLASH_STATUS_STARTED,
+				  params, NULL, NULL, 0, 0);
+}
+
+void
+ethnl_module_fw_flash_ntf_complete(struct net_device *dev,
+				   struct ethnl_module_fw_flash_ntf_params *params)
+{
+	ethnl_module_fw_flash_ntf(dev, ETHTOOL_MODULE_FW_FLASH_STATUS_COMPLETED,
+				  params, NULL, NULL, 0, 0);
+}
+
+void
+ethnl_module_fw_flash_ntf_in_progress(struct net_device *dev,
+				      struct ethnl_module_fw_flash_ntf_params *params,
+				      u64 done, u64 total)
+{
+	ethnl_module_fw_flash_ntf(dev,
+				  ETHTOOL_MODULE_FW_FLASH_STATUS_IN_PROGRESS,
+				  params, NULL, NULL, done, total);
+}
net/ethtool/module_fw.h new file +31 -0
new file mode 100644
index 000000000000..ee4a291ac1d4
@@ -0,0 +1,31 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+
+#include <uapi/linux/ethtool.h>
+
+/**
+ * struct ethnl_module_fw_flash_ntf_params - module firmware flashing
+ *						notifications parameters
+ * @portid: Netlink portid of sender.
+ * @seq: Sequence number of sender.
+ * @closed_sock: Indicates whether the socket was closed from user space.
+ */
+struct ethnl_module_fw_flash_ntf_params {
+	u32 portid;
+	u32 seq;
+	bool closed_sock;
+};
+
+void
+ethnl_module_fw_flash_ntf_err(struct net_device *dev,
+			      struct ethnl_module_fw_flash_ntf_params *params,
+			      char *err_msg, char *sub_err_msg);
+void
+ethnl_module_fw_flash_ntf_start(struct net_device *dev,
+				struct ethnl_module_fw_flash_ntf_params *params);
+void
+ethnl_module_fw_flash_ntf_complete(struct net_device *dev,
+				   struct ethnl_module_fw_flash_ntf_params *params);
+void
+ethnl_module_fw_flash_ntf_in_progress(struct net_device *dev,
+				      struct ethnl_module_fw_flash_ntf_params *params,
+				      u64 done, u64 total);
net/ethtool/netlink.c +5 -0
index bd04f28d5cf4..393ce668fb04 100644
@@ -239,6 +239,11 @@ void *ethnl_bcastmsg_put(struct sk_buff *skb, u8 cmd)
 			   cmd);
 }
 
+void *ethnl_unicast_put(struct sk_buff *skb, u32 portid, u32 seq, u8 cmd)
+{
+	return genlmsg_put(skb, portid, seq, &ethtool_genl_family, 0, cmd);
+}
+
 int ethnl_multicast(struct sk_buff *skb, struct net_device *dev)
 {
 	return genlmsg_multicast_netns(&ethtool_genl_family, dev_net(dev), skb,
net/ethtool/netlink.h +1 -0
index 9a333a8d04c1..5e6c6a7b7adc 100644
@@ -21,6 +21,7 @@ struct sk_buff *ethnl_reply_init(size_t payload, struct net_device *dev, u8 cmd,
 				 void **ehdrp);
 void *ethnl_dump_put(struct sk_buff *skb, struct netlink_callback *cb, u8 cmd);
 void *ethnl_bcastmsg_put(struct sk_buff *skb, u8 cmd);
+void *ethnl_unicast_put(struct sk_buff *skb, u32 portid, u32 seq, u8 cmd);
 int ethnl_multicast(struct sk_buff *skb, struct net_device *dev);
 
 /**
Signature · 1 line
2.45.0
reviewer
#5 lore raw

Re: [PATCH net-next v6 4/9] ethtool: Add flashing transceiver modules' firmware notifications ability

Quoted 6 lines · Danielle Ratson

Add progress notifications ability to user space while flashing modules' firmware by implementing the interface between the user space and the kernel.

...

Quoted 1 line
net/ethtool/module.c +0 -0

...

Quoted 19 lines
net/ethtool/module.c +15 -0
@@ -158,3 +159,119 @@ const struct ethnl_request_ops ethnl_module_request_ops = {
 	.set			= ethnl_set_module,
 	.set_ntf_cmd		= ETHTOOL_MSG_MODULE_NTF,
 };
+
+/* MODULE_FW_FLASH_NTF */
+
+static int
+ethnl_module_fw_flash_ntf_put_err(struct sk_buff *skb, char *err_msg,
+				  char *sub_err_msg)
+{
+	int err_msg_len, sub_err_msg_len, total_len;
+	struct nlattr *attr;
+
+	if (!err_msg)
+		return 0;
+
+	err_msg_len = strlen(err_msg);
+	total_len = err_msg_len + 2; /* For period and NUL. */

net/ethtool/module.c const struct ethnl_request_ops ethnl_module_request_ops = { · line 186

Quoted 10 lines
net/ethtool/module.c +10 -0
+
+	if (sub_err_msg) {
+		sub_err_msg_len = strlen(sub_err_msg);
+		total_len += sub_err_msg_len + 2; /* For ", ". */
+	}
+
+	attr = nla_reserve(skb, ETHTOOL_A_MODULE_FW_FLASH_STATUS_MSG,
+			   total_len);
+	if (!attr)
+		return PTR_ERR(attr);

Hi Danielle,

attr is NULL here, so I think this will return 0.
Perhaps it should return an negative error value,
say -ENOMEM, instead?

Flagged by Smatch

Quoted 8 lines
net/ethtool/module.c +8 -0
+
+	if (sub_err_msg)
+		sprintf(nla_data(attr), "%s, %s.", err_msg, sub_err_msg);
+	else
+		sprintf(nla_data(attr), "%s.", err_msg);
+
+	return 0;
+}

...

#6 lore raw

PATCH v6 5/9 ethtool: Veto some operations during firmware flashing process

In reply to Danielle Ratson

Some operations cannot be performed during the firmware flashing process.

For example:

- Port must be down during the whole flashing process to avoid packet loss while committing reset for example.

- Writing to EEPROM interrupts the flashing process, so operations like ethtool dump, module reset, get and set power mode should be vetoed.

- Split port firmware flashing should be vetoed.

In order to veto those scenarios, add a flag in 'struct net_device' that indicates when a firmware flash is taking place on the module and use it to prevent interruptions during the process.

---

Notes:
v6:
* Squash some of the vetoes from the last patch to this patch.

 include/linux/netdevice.h |  4 +++-
 net/ethtool/eeprom.c      |  6 ++++++
 net/ethtool/ioctl.c       | 12 ++++++++++++
 net/ethtool/netlink.c     | 12 ++++++++++++
 4 files changed, 33 insertions(+), 1 deletion(-)
include/linux/netdevice.h +3 -1
index f148a01dd1d1..43ec53fc0128 100644
@@ -1989,6 +1989,8 @@ enum netdev_reg_state {
  *
  *	@threaded:	napi threaded mode is enabled
  *
+ *	@module_fw_flash_in_progress:	Module firmware flashing is in progress.
+ *
  *	@net_notifier_list:	List of per-net netdev notifier block
  *				that follow this device when it is moved
  *				to another network namespace.
@@ -2373,7 +2375,7 @@ struct net_device {
 	bool			proto_down;
 	bool			threaded;
 	unsigned		wol_enabled:1;
-
+	unsigned		module_fw_flash_in_progress:1;
 	struct list_head	net_notifier_list;
 
 #if IS_ENABLED(CONFIG_MACSEC)
net/ethtool/eeprom.c +6 -0
index 6209c3a9c8f7..f36811b3ecf1 100644
@@ -91,6 +91,12 @@ static int get_module_eeprom_by_page(struct net_device *dev,
 {
 	const struct ethtool_ops *ops = dev->ethtool_ops;
 
+	if (dev->module_fw_flash_in_progress) {
+		NL_SET_ERR_MSG(extack,
+			       "Module firmware flashing is in progress");
+		return -EBUSY;
+	}
+
 	if (dev->sfp_bus)
 		return sfp_get_module_eeprom_by_page(dev->sfp_bus, page_data, extack);
 
net/ethtool/ioctl.c +12 -0
index e645d751a5e8..1cca372c0d80 100644
@@ -658,6 +658,9 @@ static int ethtool_get_settings(struct net_device *dev, void __user *useraddr)
 	if (!dev->ethtool_ops->get_link_ksettings)
 		return -EOPNOTSUPP;
 
+	if (dev->module_fw_flash_in_progress)
+		return -EBUSY;
+
 	memset(&link_ksettings, 0, sizeof(link_ksettings));
 	err = dev->ethtool_ops->get_link_ksettings(dev, &link_ksettings);
 	if (err < 0)
@@ -1449,6 +1452,9 @@ static int ethtool_reset(struct net_device *dev, char __user *useraddr)
 	if (!dev->ethtool_ops->reset)
 		return -EOPNOTSUPP;
 
+	if (dev->module_fw_flash_in_progress)
+		return -EBUSY;
+
 	if (copy_from_user(&reset, useraddr, sizeof(reset)))
 		return -EFAULT;
 
@@ -2462,6 +2468,9 @@ int ethtool_get_module_info_call(struct net_device *dev,
 	const struct ethtool_ops *ops = dev->ethtool_ops;
 	struct phy_device *phydev = dev->phydev;
 
+	if (dev->module_fw_flash_in_progress)
+		return -EBUSY;
+
 	if (dev->sfp_bus)
 		return sfp_get_module_info(dev->sfp_bus, modinfo);
 
@@ -2499,6 +2508,9 @@ int ethtool_get_module_eeprom_call(struct net_device *dev,
 	const struct ethtool_ops *ops = dev->ethtool_ops;
 	struct phy_device *phydev = dev->phydev;
 
+	if (dev->module_fw_flash_in_progress)
+		return -EBUSY;
+
 	if (dev->sfp_bus)
 		return sfp_get_module_eeprom(dev->sfp_bus, ee, data);
 
net/ethtool/netlink.c +12 -0
index 393ce668fb04..a5907bbde427 100644
@@ -765,10 +765,22 @@ static void ethnl_notify_features(struct netdev_notifier_info *info)
 static int ethnl_netdev_event(struct notifier_block *this, unsigned long event,
 			      void *ptr)
 {
+	struct netdev_notifier_info *info = ptr;
+	struct netlink_ext_ack *extack;
+	struct net_device *dev;
+
+	dev = netdev_notifier_info_to_dev(info);
+	extack = netdev_notifier_info_to_extack(info);
+
 	switch (event) {
 	case NETDEV_FEAT_CHANGE:
 		ethnl_notify_features(ptr);
 		break;
+	case NETDEV_PRE_UP:
+		if (dev->module_fw_flash_in_progress) {
+			NL_SET_ERR_MSG(extack, "Can't set port up while flashing module firmware");
+			return NOTIFY_BAD;
+		}
 	}
 
 	return NOTIFY_DONE;
Signature · 1 line
2.45.0
#7 lore raw

PATCH v6 6/9 net: sfp: Add more extended compliance codes

In reply to Danielle Ratson

SFF-8024 is used to define various constants re-used in several SFF SFP-related specifications.

Add SFF-8024 extended compliance code definitions for CMIS compliant modules and use them in the next patch to determine the firmware flashing work.

---
 include/linux/sfp.h | 6 ++++++
 1 file changed, 6 insertions(+)
include/linux/sfp.h +6 -0
index a45da7eef9a2..b14be59550e3 100644
@@ -284,6 +284,12 @@ enum {
 	SFF8024_ID_QSFP_8438		= 0x0c,
 	SFF8024_ID_QSFP_8436_8636	= 0x0d,
 	SFF8024_ID_QSFP28_8636		= 0x11,
+	SFF8024_ID_QSFP_DD		= 0x18,
+	SFF8024_ID_OSFP			= 0x19,
+	SFF8024_ID_DSFP			= 0x1B,
+	SFF8024_ID_QSFP_PLUS_CMIS	= 0x1E,
+	SFF8024_ID_SFP_DD_CMIS		= 0x1F,
+	SFF8024_ID_SFP_PLUS_CMIS	= 0x20,
 
 	SFF8024_ENCODING_UNSPEC		= 0x00,
 	SFF8024_ENCODING_8B10B		= 0x01,
Signature · 1 line
2.45.0
#8 lore raw

PATCH v6 7/9 ethtool: cmis_cdb: Add a layer for supporting CDB commands

In reply to Danielle Ratson

CDB (Command Data Block Message Communication) reads and writes are performed on memory map pages 9Fh-AFh according to the CMIS standard, section 8.20 of revision 5.2.
Page 9Fh is used to specify the CDB command to be executed and also provides an area for a local payload (LPL).

According to the CMIS standard, the firmware update process is done using a CDB commands sequence that will be implemented in the next patch.

The kernel interface that will implement the firmware update using CDB command will include 2 layers that will be added under ethtool:

* The upper layer that will be triggered from the module layer, is cmis_fw_update.
* The lower one is cmis_cdb.

In the future there might be more operations to implement using CDB commands. Therefore, the idea is to keep the CDB interface clean and the cmis_fw_update specific to the CDB commands handling it.

These two layers will communicate using the API the consists of three functions:

- struct ethtool_cmis_cdb *
ethtool_cmis_cdb_init(struct net_device *dev,

			struct ethtool_module_fw_flash_params *params);
- void ethtool_cmis_cdb_fini(struct ethtool_cmis_cdb *cdb);
- int ethtool_cmis_cdb_execute_cmd(struct net_device *dev,
				   struct ethtool_cmis_cdb_cmd_args *args);

Add the CDB layer to support initializing, finishing and executing CDB commands:

* The initialization process will include creating of an ethtool_cmis_cdb instance, querying the module CDB support, entering and validating the password from user space (CMD 0x0000) and querying the module features (CMD 0x0040).

* The finishing API will simply free the ethtool_cmis_cdb instance.

* The executing process will write the CDB command to EEPROM using set_module_eeprom_by_page() that was presented earlier, and will process the reply from EEPROM.

---

Notes:

    v6:
    	* In ethtool_cmis_cdb_init(), Use 'const' for the params
    	  parameter.
    
    v5:
    	* Drop all the inline in cmis_cdb.c.
    
    v4:
    	* Add kernel-doc for msleep_pre_rpl and err_msg.
    
    v3:
    	* Use kmemdup() instead of kmalloc+memcpy.
    
    v2:
    	* Define ethtool_cmis_cdb_request::epl_len to be __be16 instead
    	  of u16.
 net/ethtool/Makefile    |   2 +-
 net/ethtool/cmis.h      | 117 ++++++++
 net/ethtool/cmis_cdb.c  | 581 ++++++++++++++++++++++++++++++++++++++++
 net/ethtool/module_fw.h |  10 +
 4 files changed, 709 insertions(+), 1 deletion(-)
 create mode 100644 net/ethtool/cmis.h
 create mode 100644 net/ethtool/cmis_cdb.c
net/ethtool/Makefile +1 -1
index 504f954a1b28..38806b3ecf83 100644
@@ -8,4 +8,4 @@ ethtool_nl-y	:= netlink.o bitset.o strset.o linkinfo.o linkmodes.o rss.o \
 		   linkstate.o debug.o wol.o features.o privflags.o rings.o \
 		   channels.o coalesce.o pause.o eee.o tsinfo.o cabletest.o \
 		   tunnels.o fec.o eeprom.o stats.o phc_vclocks.o mm.o \
-		   module.o pse-pd.o plca.o mm.o
+		   module.o cmis_cdb.o pse-pd.o plca.o mm.o
net/ethtool/cmis.h new file +117 -0

117 lines not on this page · raw message

net/ethtool/cmis_cdb.c new file +581 -0

581 lines not on this page · raw message

net/ethtool/module_fw.h +10 -0
index ee4a291ac1d4..6c86d05ab6cf 100644
@@ -15,6 +15,16 @@ struct ethnl_module_fw_flash_ntf_params {
 	bool closed_sock;
 };
 
+/**
+ * struct ethtool_module_fw_flash_params - module firmware flashing parameters
+ * @password: Module password. Only valid when @pass_valid is set.
+ * @password_valid: Whether the module password is valid or not.
+ */
+struct ethtool_module_fw_flash_params {
+	__be32 password;
+	u8 password_valid:1;
+};
+
 void
 ethnl_module_fw_flash_ntf_err(struct net_device *dev,
 			      struct ethnl_module_fw_flash_ntf_params *params,
Signature · 1 line
2.45.0
#9 lore raw

PATCH v6 8/9 ethtool: cmis_fw_update: add a layer for supporting firmware update using CDB

In reply to Danielle Ratson

According to the CMIS standard, the firmware update process is done using a CDB commands sequence.

Implement a work that will be triggered from the module layer in the next patch the will initiate and execute all the CDB commands in order, to eventually complete the firmware update process.

This flashing process includes, writing the firmware image, running the new firmware image and committing it after testing, so that it will run upon reset.

This work will also notify user space about the progress of the firmware update process.

---

Notes:
v6:
* Add a list field to struct ethtool_module_fw_flash for module_fw_flash_work_list that will be presented in the next patch.
* Move ethtool_cmis_fw_update() cleaning to a new function that will be represented in the next patch.
* Move some of the fields in struct ethtool_module_fw_flash to a separate struct, so ethtool_cmis_fw_update() will get only the relevant parameters for it.
* Edit the relevant functions to get the relevant params for them.
* s/CMIS_MODULE_READY_MAX_DURATION_USEC/CMIS_MODULE_READY_MAX_DURATION_MSEC.

v2:
* Decrease msleep before querying completion flag in Write FW Image command.
* Change the condition for failing when LPL is not supported.
* Re-write cmis_fw_update_write_image().

 net/ethtool/Makefile         |   2 +-
 net/ethtool/cmis.h           |   7 +
 net/ethtool/cmis_fw_update.c | 399 +++++++++++++++++++++++++++++++++++
 net/ethtool/module_fw.h      |  31 +++
 4 files changed, 438 insertions(+), 1 deletion(-)
 create mode 100644 net/ethtool/cmis_fw_update.c
net/ethtool/Makefile +1 -1
index 38806b3ecf83..9a190635fe95 100644
@@ -8,4 +8,4 @@ ethtool_nl-y	:= netlink.o bitset.o strset.o linkinfo.o linkmodes.o rss.o \
 		   linkstate.o debug.o wol.o features.o privflags.o rings.o \
 		   channels.o coalesce.o pause.o eee.o tsinfo.o cabletest.o \
 		   tunnels.o fec.o eeprom.o stats.o phc_vclocks.o mm.o \
-		   module.o cmis_cdb.o pse-pd.o plca.o mm.o
+		   module.o cmis_fw_update.o cmis_cdb.o pse-pd.o plca.o mm.o
net/ethtool/cmis.h +7 -0
index 295f5d0df915..e71cc3e1b7eb 100644
@@ -20,6 +20,12 @@ struct ethtool_cmis_cdb {
 enum ethtool_cmis_cdb_cmd_id {
 	ETHTOOL_CMIS_CDB_CMD_QUERY_STATUS		= 0x0000,
 	ETHTOOL_CMIS_CDB_CMD_MODULE_FEATURES		= 0x0040,
+	ETHTOOL_CMIS_CDB_CMD_FW_MANAGMENT_FEATURES	= 0x0041,
+	ETHTOOL_CMIS_CDB_CMD_START_FW_DOWNLOAD		= 0x0101,
+	ETHTOOL_CMIS_CDB_CMD_WRITE_FW_BLOCK_LPL		= 0x0103,
+	ETHTOOL_CMIS_CDB_CMD_COMPLETE_FW_DOWNLOAD	= 0x0107,
+	ETHTOOL_CMIS_CDB_CMD_RUN_FW_IMAGE		= 0x0109,
+	ETHTOOL_CMIS_CDB_CMD_COMMIT_FW_IMAGE		= 0x010A,
 };
 
 /**
@@ -47,6 +53,7 @@ struct ethtool_cmis_cdb_request {
 
 #define CDB_F_COMPLETION_VALID		BIT(0)
 #define CDB_F_STATUS_VALID		BIT(1)
+#define CDB_F_MODULE_STATE_VALID	BIT(2)
 
 /**
  * struct ethtool_cmis_cdb_cmd_args - CDB commands execution arguments
net/ethtool/cmis_fw_update.c new file +399 -0

399 lines not on this page · raw message

net/ethtool/module_fw.h +31 -0
index 6c86d05ab6cf..d0fc2529b60e 100644
@@ -25,6 +25,35 @@ struct ethtool_module_fw_flash_params {
 	u8 password_valid:1;
 };
 
+/**
+ * struct ethtool_cmis_fw_update_params - CMIS firmware update specific
+ *						parameters
+ * @dev: Pointer to the net_device to be flashed.
+ * @params: Module firmware flashing parameters.
+ * @ntf_params: Module firmware flashing notification parameters.
+ * @fw: Firmware to flash.
+ */
+struct ethtool_cmis_fw_update_params {
+	struct net_device *dev;
+	struct ethtool_module_fw_flash_params params;
+	struct ethnl_module_fw_flash_ntf_params ntf_params;
+	const struct firmware *fw;
+};
+
+/**
+ * struct ethtool_module_fw_flash - module firmware flashing
+ * @list: List node for &module_fw_flash_work_list.
+ * @dev_tracker: Refcount tracker for @dev.
+ * @work: The flashing firmware work.
+ * @fw_update: CMIS firmware update specific parameters.
+ */
+struct ethtool_module_fw_flash {
+	struct list_head list;
+	netdevice_tracker dev_tracker;
+	struct work_struct work;
+	struct ethtool_cmis_fw_update_params fw_update;
+};
+
 void
 ethnl_module_fw_flash_ntf_err(struct net_device *dev,
 			      struct ethnl_module_fw_flash_ntf_params *params,
@@ -39,3 +68,5 @@ void
 ethnl_module_fw_flash_ntf_in_progress(struct net_device *dev,
 				      struct ethnl_module_fw_flash_ntf_params *params,
 				      u64 done, u64 total);
+
+void ethtool_cmis_fw_update(struct ethtool_cmis_fw_update_params *params);
Signature · 1 line
2.45.0
#10 lore raw

PATCH v6 9/9 ethtool: Add ability to flash transceiver modules' firmware

In reply to Danielle Ratson

Add the ability to flash the modules' firmware by implementing the interface between the user space and the kernel.

Example from a succeeding implementation:

 # ethtool --flash-module-firmware swp40 file test.bin

Transceiver module firmware flashing started for device swp40 Transceiver module firmware flashing in progress for device swp40
Progress: 99%
Transceiver module firmware flashing completed for device swp40

In addition, add infrastructure that allows modules to set socket-specific private data. This ensures that when a socket is closed from user space during the flashing process, the right socket halts sending notifications to user space until the work item is completed.

---

Notes:
v6:
* Add a paragraph in the commit message.
* Rename labels in module_flash_fw_schedule().
* Add info to genl_sk_priv_*() and implement the relevant callbacks, in order to handle properly a scenario of closing the socket from user space before the work item was ended.
* Add a list the holds all the ethtool_module_fw_flash struct that corresponds to the in progress work items.
* Add a new enum for the socket types.
* Use both above to identify a flashing socket, add it to the list and when closing socket affect only the flashing type.
* Create a new function that will get the work item instead of ethtool_cmis_fw_update().
* Edit the relevant functions to get the relevant params for them.
* The new function will call the old ethtool_cmis_fw_update(), and do the cleaning, so the existence of the list should be completely isolated in module.c.

 net/ethtool/module.c    | 275 ++++++++++++++++++++++++++++++++++++++++
 net/ethtool/module_fw.h |   3 +
 net/ethtool/netlink.c   |  38 ++++++
 net/ethtool/netlink.h   |  15 +++
 4 files changed, 331 insertions(+)
net/ethtool/module.c +275 -0
index 932415bd44c6..7e4ea0596508 100644
@@ -1,6 +1,9 @@
 // SPDX-License-Identifier: GPL-2.0-only
 
 #include <linux/ethtool.h>
+#include <linux/firmware.h>
+#include <linux/sfp.h>
+#include <net/devlink.h>
 
 #include "netlink.h"
 #include "common.h"
@@ -34,6 +37,12 @@ static int module_get_power_mode(struct net_device *dev,
 	if (!ops->get_module_power_mode)
 		return 0;
 
+	if (dev->module_fw_flash_in_progress) {
+		NL_SET_ERR_MSG(extack,
+			       "Module firmware flashing is in progress");
+		return -EBUSY;
+	}
+
 	return ops->get_module_power_mode(dev, &data->power, extack);
 }
 
@@ -110,6 +119,12 @@ ethnl_set_module_validate(struct ethnl_req_info *req_info,
 	if (!tb[ETHTOOL_A_MODULE_POWER_MODE_POLICY])
 		return 0;
 
+	if (req_info->dev->module_fw_flash_in_progress) {
+		NL_SET_ERR_MSG(info->extack,
+			       "Module firmware flashing is in progress");
+		return -EBUSY;
+	}
+
 	if (!ops->get_module_power_mode || !ops->set_module_power_mode) {
 		NL_SET_ERR_MSG_ATTR(info->extack,
 				    tb[ETHTOOL_A_MODULE_POWER_MODE_POLICY],
@@ -160,6 +175,266 @@ const struct ethnl_request_ops ethnl_module_request_ops = {
 	.set_ntf_cmd		= ETHTOOL_MSG_MODULE_NTF,
 };
 
+/* MODULE_FW_FLASH_ACT */
+
+const struct nla_policy
+ethnl_module_fw_flash_act_policy[ETHTOOL_A_MODULE_FW_FLASH_PASSWORD + 1] = {
+	[ETHTOOL_A_MODULE_FW_FLASH_HEADER] =
+		NLA_POLICY_NESTED(ethnl_header_policy),
+	[ETHTOOL_A_MODULE_FW_FLASH_FILE_NAME] = { .type = NLA_NUL_STRING },
+	[ETHTOOL_A_MODULE_FW_FLASH_PASSWORD] = { .type = NLA_U32 },
+};
+
+static LIST_HEAD(module_fw_flash_work_list);
+static DEFINE_SPINLOCK(module_fw_flash_work_list_lock);
+
+static int
+module_flash_fw_work_list_add(struct ethtool_module_fw_flash *module_fw,
+			      struct genl_info *info)
+{
+	struct ethtool_module_fw_flash *work;
+
+	/* First, check if already registered. */
+	spin_lock(&module_fw_flash_work_list_lock);
+	list_for_each_entry(work, &module_fw_flash_work_list, list) {
+		if (work->fw_update.ntf_params.portid == info->snd_portid &&
+		    work->fw_update.dev == module_fw->fw_update.dev)
+			return -EALREADY;
+	}
+
+	list_add_tail(&module_fw->list, &module_fw_flash_work_list);
+	spin_unlock(&module_fw_flash_work_list_lock);
+
+	return 0;
+}
+
+static void module_flash_fw_work_list_del(struct list_head *list)
+{
+	spin_lock(&module_fw_flash_work_list_lock);
+	list_del(list);
+	spin_unlock(&module_fw_flash_work_list_lock);
+}
+
+static void module_flash_fw_work(struct work_struct *work)
+{
+	struct ethtool_module_fw_flash *module_fw;
+
+	module_fw = container_of(work, struct ethtool_module_fw_flash, work);
+
+	ethtool_cmis_fw_update(&module_fw->fw_update);
+
+	module_flash_fw_work_list_del(&module_fw->list);
+	module_fw->fw_update.dev->module_fw_flash_in_progress = false;
+	netdev_put(module_fw->fw_update.dev, &module_fw->dev_tracker);
+	release_firmware(module_fw->fw_update.fw);
+	kfree(module_fw);
+}
+
+#define MODULE_EEPROM_PHYS_ID_PAGE	0
+#define MODULE_EEPROM_PHYS_ID_I2C_ADDR	0x50
+
+static int module_flash_fw_work_init(struct ethtool_module_fw_flash *module_fw,
+				     struct net_device *dev,
+				     struct netlink_ext_ack *extack)
+{
+	const struct ethtool_ops *ops = dev->ethtool_ops;
+	struct ethtool_module_eeprom page_data = {};
+	u8 phys_id;
+	int err;
+
+	/* Fetch the SFF-8024 Identifier Value. For all supported standards, it
+	 * is located at I2C address 0x50, byte 0. See section 4.1 in SFF-8024,
+	 * revision 4.9.
+	 */
+	page_data.page = MODULE_EEPROM_PHYS_ID_PAGE;
+	page_data.offset = SFP_PHYS_ID;
+	page_data.length = sizeof(phys_id);
+	page_data.i2c_address = MODULE_EEPROM_PHYS_ID_I2C_ADDR;
+	page_data.data = &phys_id;
+
+	err = ops->get_module_eeprom_by_page(dev, &page_data, extack);
+	if (err < 0)
+		return err;
+
+	switch (phys_id) {
+	case SFF8024_ID_QSFP_DD:
+	case SFF8024_ID_OSFP:
+	case SFF8024_ID_DSFP:
+	case SFF8024_ID_QSFP_PLUS_CMIS:
+	case SFF8024_ID_SFP_DD_CMIS:
+	case SFF8024_ID_SFP_PLUS_CMIS:
+		INIT_WORK(&module_fw->work, module_flash_fw_work);
+		break;
+	default:
+		NL_SET_ERR_MSG(extack,
+			       "Module type does not support firmware flashing");
+		return -EOPNOTSUPP;
+	}
+
+	return 0;
+}
+
+void ethnl_module_fw_flash_sock_destroy(struct ethnl_sock_priv *sk_priv)
+{
+	struct ethtool_module_fw_flash *work;
+
+	spin_lock(&module_fw_flash_work_list_lock);
+	list_for_each_entry(work, &module_fw_flash_work_list, list) {
+		if (work->fw_update.dev == sk_priv->dev &&
+		    work->fw_update.ntf_params.portid == sk_priv->portid) {
+			work->fw_update.ntf_params.closed_sock = true;
+			break;
+		}
+	}
+	spin_unlock(&module_fw_flash_work_list_lock);
+}
+
+static int
+module_flash_fw_schedule(struct net_device *dev, const char *file_name,
+			 struct ethtool_module_fw_flash_params *params,
+			 struct sk_buff *skb, struct genl_info *info)
+{
+	struct ethtool_cmis_fw_update_params *fw_update;
+	struct ethtool_module_fw_flash *module_fw;
+	int err;
+
+	module_fw = kzalloc(sizeof(*module_fw), GFP_KERNEL);
+	if (!module_fw)
+		return -ENOMEM;
+
+	fw_update = &module_fw->fw_update;
+	fw_update->params = *params;
+	err = request_firmware_direct(&fw_update->fw,
+				      file_name, &dev->dev);
+	if (err) {
+		NL_SET_ERR_MSG(info->extack,
+			       "Failed to request module firmware image");
+		goto err_free;
+	}
+
+	err = module_flash_fw_work_init(module_fw, dev, info->extack);
+	if (err < 0)
+		goto err_release_firmware;
+
+	dev->module_fw_flash_in_progress = true;
+	netdev_hold(dev, &module_fw->dev_tracker, GFP_KERNEL);
+	fw_update->dev = dev;
+	fw_update->ntf_params.portid = info->snd_portid;
+	fw_update->ntf_params.seq = info->snd_seq;
+	fw_update->ntf_params.closed_sock = false;
+
+	err = ethnl_sock_priv_set(skb, dev, fw_update->ntf_params.portid,
+				  ETHTOOL_SOCK_TYPE_MODULE_FW_FLASH);
+	if (err < 0)
+		goto err_release_firmware;
+
+	err = module_flash_fw_work_list_add(module_fw, info);
+	if (err < 0)
+		goto err_release_firmware;
+
+	schedule_work(&module_fw->work);
+
+	return 0;
+
+err_release_firmware:
+	release_firmware(fw_update->fw);
+err_free:
+	kfree(module_fw);
+	return err;
+}
+
+static int module_flash_fw(struct net_device *dev, struct nlattr **tb,
+			   struct sk_buff *skb, struct genl_info *info)
+{
+	struct ethtool_module_fw_flash_params params = {};
+	const char *file_name;
+	struct nlattr *attr;
+
+	if (GENL_REQ_ATTR_CHECK(info, ETHTOOL_A_MODULE_FW_FLASH_FILE_NAME))
+		return -EINVAL;
+
+	file_name = nla_data(tb[ETHTOOL_A_MODULE_FW_FLASH_FILE_NAME]);
+
+	attr = tb[ETHTOOL_A_MODULE_FW_FLASH_PASSWORD];
+	if (attr) {
+		params.password = cpu_to_be32(nla_get_u32(attr));
+		params.password_valid = true;
+	}
+
+	return module_flash_fw_schedule(dev, file_name, &params, skb, info);
+}
+
+static int ethnl_module_fw_flash_validate(struct net_device *dev,
+					  struct netlink_ext_ack *extack)
+{
+	struct devlink_port *devlink_port = dev->devlink_port;
+	const struct ethtool_ops *ops = dev->ethtool_ops;
+
+	if (!ops->set_module_eeprom_by_page ||
+	    !ops->get_module_eeprom_by_page) {
+		NL_SET_ERR_MSG(extack,
+			       "Flashing module firmware is not supported by this device");
+		return -EOPNOTSUPP;
+	}
+
+	if (!ops->reset) {
+		NL_SET_ERR_MSG(extack,
+			       "Reset module is not supported by this device, so flashing is not permitted");
+		return -EOPNOTSUPP;
+	}
+
+	if (dev->module_fw_flash_in_progress) {
+		NL_SET_ERR_MSG(extack, "Module firmware flashing already in progress");
+		return -EBUSY;
+	}
+
+	if (dev->flags & IFF_UP) {
+		NL_SET_ERR_MSG(extack, "Netdevice is up, so flashing is not permitted");
+		return -EBUSY;
+	}
+
+	if (devlink_port && devlink_port->attrs.split) {
+		NL_SET_ERR_MSG(extack, "Can't perform firmware flashing on a split port");
+		return -EOPNOTSUPP;
+	}
+
+	return 0;
+}
+
+int ethnl_act_module_fw_flash(struct sk_buff *skb, struct genl_info *info)
+{
+	struct ethnl_req_info req_info = {};
+	struct nlattr **tb = info->attrs;
+	struct net_device *dev;
+	int ret;
+
+	ret = ethnl_parse_header_dev_get(&req_info,
+					 tb[ETHTOOL_A_MODULE_FW_FLASH_HEADER],
+					 genl_info_net(info), info->extack,
+					 true);
+	if (ret < 0)
+		return ret;
+	dev = req_info.dev;
+
+	rtnl_lock();
+	ret = ethnl_ops_begin(dev);
+	if (ret < 0)
+		goto out_rtnl;
+
+	ret = ethnl_module_fw_flash_validate(dev, info->extack);
+	if (ret < 0)
+		goto out_rtnl;
+
+	ret = module_flash_fw(dev, tb, skb, info);
+
+	ethnl_ops_complete(dev);
+
+out_rtnl:
+	rtnl_unlock();
+	ethnl_parse_header_dev_put(&req_info);
+	return ret;
+}
+
 /* MODULE_FW_FLASH_NTF */
 
 static int
net/ethtool/module_fw.h +3 -0
index d0fc2529b60e..634543a12d0c 100644
@@ -1,6 +1,7 @@
 /* SPDX-License-Identifier: GPL-2.0-only */
 
 #include <uapi/linux/ethtool.h>
+#include "netlink.h"
 
 /**
  * struct ethnl_module_fw_flash_ntf_params - module firmware flashing
@@ -54,6 +55,8 @@ struct ethtool_module_fw_flash {
 	struct ethtool_cmis_fw_update_params fw_update;
 };
 
+void ethnl_module_fw_flash_sock_destroy(struct ethnl_sock_priv *sk_priv);
+
 void
 ethnl_module_fw_flash_ntf_err(struct net_device *dev,
 			      struct ethnl_module_fw_flash_ntf_params *params,
net/ethtool/netlink.c +38 -0
index a5907bbde427..a5e6f341e4b9 100644
@@ -4,6 +4,7 @@
 #include <linux/ethtool_netlink.h>
 #include <linux/pm_runtime.h>
 #include "netlink.h"
+#include "module_fw.h"
 
 static struct genl_family ethtool_genl_family;
 
@@ -30,6 +31,34 @@ const struct nla_policy ethnl_header_policy_stats[] = {
 							  ETHTOOL_FLAGS_STATS),
 };
 
+int ethnl_sock_priv_set(struct sk_buff *skb, struct net_device *dev, u32 portid,
+			enum ethnl_sock_type type)
+{
+	struct ethnl_sock_priv *sk_priv;
+
+	sk_priv = genl_sk_priv_get(&ethtool_genl_family, NETLINK_CB(skb).sk);
+	if (IS_ERR(sk_priv))
+		return PTR_ERR(sk_priv);
+
+	sk_priv->dev = dev;
+	sk_priv->portid = portid;
+	sk_priv->type = type;
+
+	return 0;
+}
+
+static void ethnl_sock_priv_destroy(void *priv)
+{
+	struct ethnl_sock_priv *sk_priv = priv;
+
+	switch (sk_priv->type) {
+	case ETHTOOL_SOCK_TYPE_MODULE_FW_FLASH:
+		ethnl_module_fw_flash_sock_destroy(sk_priv);
+	default:
+		break;
+	}
+}
+
 int ethnl_ops_begin(struct net_device *dev)
 {
 	int ret;
@@ -1142,6 +1171,13 @@ static const struct genl_ops ethtool_genl_ops[] = {
 		.policy = ethnl_mm_set_policy,
 		.maxattr = ARRAY_SIZE(ethnl_mm_set_policy) - 1,
 	},
+	{
+		.cmd	= ETHTOOL_MSG_MODULE_FW_FLASH_ACT,
+		.flags	= GENL_UNS_ADMIN_PERM,
+		.doit	= ethnl_act_module_fw_flash,
+		.policy	= ethnl_module_fw_flash_act_policy,
+		.maxattr = ARRAY_SIZE(ethnl_module_fw_flash_act_policy) - 1,
+	},
 };
 
 static const struct genl_multicast_group ethtool_nl_mcgrps[] = {
@@ -1158,6 +1194,8 @@ static struct genl_family ethtool_genl_family __ro_after_init = {
 	.resv_start_op	= ETHTOOL_MSG_MODULE_GET + 1,
 	.mcgrps		= ethtool_nl_mcgrps,
 	.n_mcgrps	= ARRAY_SIZE(ethtool_nl_mcgrps),
+	.sock_priv_size		= sizeof(struct ethnl_sock_priv),
+	.sock_priv_destroy	= ethnl_sock_priv_destroy,
 };
 
 /* module setup */
net/ethtool/netlink.h +15 -0
index 5e6c6a7b7adc..46ec273a87c5 100644
@@ -284,6 +284,19 @@ struct ethnl_reply_data {
 int ethnl_ops_begin(struct net_device *dev);
 void ethnl_ops_complete(struct net_device *dev);
 
+enum ethnl_sock_type {
+	ETHTOOL_SOCK_TYPE_MODULE_FW_FLASH,
+};
+
+struct ethnl_sock_priv {
+	struct net_device *dev;
+	u32 portid;
+	enum ethnl_sock_type type;
+};
+
+int ethnl_sock_priv_set(struct sk_buff *skb, struct net_device *dev, u32 portid,
+			enum ethnl_sock_type type);
+
 /**
  * struct ethnl_request_ops - unified handling of GET and SET requests
  * @request_cmd:      command id for request (GET)
@@ -442,6 +455,7 @@ extern const struct nla_policy ethnl_plca_set_cfg_policy[ETHTOOL_A_PLCA_MAX + 1]
 extern const struct nla_policy ethnl_plca_get_status_policy[ETHTOOL_A_PLCA_HEADER + 1];
 extern const struct nla_policy ethnl_mm_get_policy[ETHTOOL_A_MM_HEADER + 1];
 extern const struct nla_policy ethnl_mm_set_policy[ETHTOOL_A_MM_MAX + 1];
+extern const struct nla_policy ethnl_module_fw_flash_act_policy[ETHTOOL_A_MODULE_FW_FLASH_PASSWORD + 1];
 
 int ethnl_set_features(struct sk_buff *skb, struct genl_info *info);
 int ethnl_act_cable_test(struct sk_buff *skb, struct genl_info *info);
@@ -449,6 +463,7 @@ int ethnl_act_cable_test_tdr(struct sk_buff *skb, struct genl_info *info);
 int ethnl_tunnel_info_doit(struct sk_buff *skb, struct genl_info *info);
 int ethnl_tunnel_info_start(struct netlink_callback *cb);
 int ethnl_tunnel_info_dumpit(struct sk_buff *skb, struct netlink_callback *cb);
+int ethnl_act_module_fw_flash(struct sk_buff *skb, struct genl_info *info);
 
 extern const char stats_std_names[__ETHTOOL_STATS_CNT][ETH_GSTRING_LEN];
 extern const char stats_eth_phy_names[__ETHTOOL_A_STATS_ETH_PHY_CNT][ETH_GSTRING_LEN];
Signature · 1 line
2.45.0
maintainer
#11 lore raw

Re: [PATCH net-next v6 9/9] ethtool: Add ability to flash transceiver modules' firmware

net/ethtool/netlink.c const struct nla_policy ethnl_header_policy_stats[] = { · line 58

Quoted 5 lines · On Wed, 19 Jun 2024 15:17:27 +0300 Danielle Ratson wrote:
net/ethtool/netlink.c +5 -0
+	switch (sk_priv->type) {
+	case ETHTOOL_SOCK_TYPE_MODULE_FW_FLASH:
+		ethnl_module_fw_flash_sock_destroy(sk_priv);
+	default:
+		break;

The compilers are nit picking on this:

net/ethtool/netlink.c:57:2: warning: unannotated fall-through between switch labels [-Wimplicit-fallthrough]

   57 |         default:
      |         ^
net/ethtool/netlink.c:57:2: note: insert 'break;' to avoid fall-through
   57 |         default:
      |         ^
Signature · 1 line
pw-bot: cr
#12 lore raw

Re: [PATCH net-next v6 9/9] ethtool: Add ability to flash transceiver modules' firmware

In reply to Danielle Ratson

Hi Danielle,

kernel test robot noticed the following build warnings:

url:    https://github.com/intel-lab-lkp/linux/commits/Danielle-Ratson/ethtool-Add-ethtool-operation-to-write-to-a-transceiver-module-EEPROM/20240619-202527
base:   net-next/main
patch link:    https://lore.kernel.org/r/20240619121727.3643161-10-danieller%40nvidia.com
patch subject: [PATCH net-next v6 9/9] ethtool: Add ability to flash transceiver modules' firmware
config: x86_64-randconfig-161-20240620 (https://download.01.org/0day-ci/archive/20240621/[email protected]/config)
compiler: gcc-13 (Ubuntu 13.2.0-4ubuntu3) 13.2.0

If you fix the issue in a separate patch/commit (i.e. not just a new version of the same patch/commit), kindly add following tags

| Reported-by: kernel test robot <[email protected]>
| Reported-by: Dan Carpenter <[email protected]>
| Closes: https://lore.kernel.org/r/[email protected]/

New smatch warnings:
net/ethtool/module.c:208 module_flash_fw_work_list_add() warn: inconsistent returns '&module_fw_flash_work_list_lock'.

vim +208 net/ethtool/module.c

d55d0c47876a6d Danielle Ratson 2024-06-19  191  static int
d55d0c47876a6d Danielle Ratson 2024-06-19  192  module_flash_fw_work_list_add(struct ethtool_module_fw_flash *module_fw,
d55d0c47876a6d Danielle Ratson 2024-06-19  193  			      struct genl_info *info)
d55d0c47876a6d Danielle Ratson 2024-06-19  194  {
d55d0c47876a6d Danielle Ratson 2024-06-19  195  	struct ethtool_module_fw_flash *work;
d55d0c47876a6d Danielle Ratson 2024-06-19  196  
d55d0c47876a6d Danielle Ratson 2024-06-19  197  	/* First, check if already registered. */
d55d0c47876a6d Danielle Ratson 2024-06-19  198  	spin_lock(&module_fw_flash_work_list_lock);
d55d0c47876a6d Danielle Ratson 2024-06-19  199  	list_for_each_entry(work, &module_fw_flash_work_list, list) {
d55d0c47876a6d Danielle Ratson 2024-06-19  200  		if (work->fw_update.ntf_params.portid == info->snd_portid &&
d55d0c47876a6d Danielle Ratson 2024-06-19  201  		    work->fw_update.dev == module_fw->fw_update.dev)
	spin_unlock(&module_fw_flash_work_list_lock);
d55d0c47876a6d Danielle Ratson 2024-06-19  202  			return -EALREADY;
d55d0c47876a6d Danielle Ratson 2024-06-19  203  	}
d55d0c47876a6d Danielle Ratson 2024-06-19  204  
d55d0c47876a6d Danielle Ratson 2024-06-19  205  	list_add_tail(&module_fw->list, &module_fw_flash_work_list);
d55d0c47876a6d Danielle Ratson 2024-06-19  206  	spin_unlock(&module_fw_flash_work_list_lock);
d55d0c47876a6d Danielle Ratson 2024-06-19  207  

d55d0c47876a6d Danielle Ratson 2024-06-19 @208 return 0;
d55d0c47876a6d Danielle Ratson 2024-06-19 209 }

Signature · 2 lines
0-DAY CI Kernel Test Service
https://github.com/intel/lkp-tests/wiki