ARM: imx: Enable PCA953x driver on DH i.MX8MP DHCOM PDK2
PATCH 1/2 ARM: imx: Enable PCA953x driver on DH i.MX8MP DHCOM PDK2
Enable PCA953x GPIO expander driver in DH i.MX8MP DHCOM PDK2 configuration. The PCA9539 GPIO expander is used on production DH i.MX8MP DHCOM SoM rev.200. This is already enabled in DH i.MX8MP DHCOM PDK3 configuration so align the two configurations.
---
Cc: "NXP i.MX U-Boot Team" <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: [email protected]
Cc: [email protected]
--- configs/imx8mp_dhcom_pdk2_defconfig | 1 + 1 file changed, 1 insertion(+)
configs/imx8mp_dhcom_pdk2_defconfig +1 -0
@@ -182,6 +182,7 @@ CONFIG_FASTBOOT_FLASH_MMC_DEV=0 CONFIG_GPIO_HOG=y CONFIG_SPL_GPIO_HOG=y CONFIG_MXC_GPIO=y +CONFIG_DM_PCA953X=y CONFIG_DM_I2C=y # CONFIG_INPUT is not set CONFIG_LED=y
Signature · 1 line
2.43.0
PATCH 2/2 ARM: imx: Update Fast ethernet PHY MDIO addresses to match DH i.MX8MP DHCOM rev.200
The production DH i.MX8MP DHCOM SoM rev.200 uses updated PHY MDIO addresses for the Fast ethernet PHYs. Update the base SoM DT and SoM rev.100 backward compatibility DTO to cater for this change.
Since the MDIO address adjustment is now also in the rev.100 SoM DTO, not only in the rev.100 PDK3 DTO, update Makefile accordingly as well, else the DTC would complain about the DTO overriding the 'reg' property without also updating the node unit-address, which is not doable without duplicating the entire PHY node in the DTO, which leads to large amount of duplication with no gain.
---
Cc: "NXP i.MX U-Boot Team" <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: [email protected]
Cc: [email protected]
--- arch/arm/dts/Makefile | 1 + arch/arm/dts/imx8mp-dhcom-som-overlay-rev100.dts | 5 +++++ arch/arm/dts/imx8mp-dhcom-som.dtsi | 8 ++++---- 3 files changed, 10 insertions(+), 4 deletions(-)
arch/arm/dts/Makefile +1 -0
@@ -1291,6 +1291,7 @@ targets += $(dtb-y) # Add any required device tree compiler flags here DTC_FLAGS += -a 0x8 +DTC_FLAGS_imx8mp-dhcom-som-overlay-rev100 += -Wno-avoid_default_addr_size -Wno-reg_format DTC_FLAGS_imx8mp-dhcom-pdk3-overlay-rev100 += -Wno-avoid_default_addr_size -Wno-reg_format PHONY += dtbs
arch/arm/dts/imx8mp-dhcom-som-overlay-rev100.dts +5 -0
@@ -35,6 +35,7 @@ ðphy0f { /* SMSC LAN8740Ai */ pinctrl-0 = <&pinctrl_ethphy0 &pinctrl_ioexp>; reset-gpios = <&gpio3 20 GPIO_ACTIVE_LOW>; + reg = <0>; }; ðphy0g { /* Micrel KSZ9131RNXI */
@@ -42,6 +43,10 @@ reset-gpios = <&gpio3 20 GPIO_ACTIVE_LOW>; }; +ðphy1f { /* SMSC LAN8740Ai */ + reg = <1>; +}; + &i2c3 { adc@48 { compatible = "ti,tla2024";
arch/arm/dts/imx8mp-dhcom-som.dtsi +4 -4
@@ -100,14 +100,14 @@ #size-cells = <0>; /* Up to one of these two PHYs may be populated. */ - ethphy0f: ethernet-phy@0 { /* SMSC LAN8740Ai */ + ethphy0f: ethernet-phy@1 { /* SMSC LAN8740Ai */ compatible = "ethernet-phy-id0007.c110", "ethernet-phy-ieee802.3-c22"; interrupt-parent = <&gpio3>; interrupts = <19 IRQ_TYPE_LEVEL_LOW>; pinctrl-0 = <&pinctrl_ethphy0>; pinctrl-names = "default"; - reg = <0>; + reg = <1>; reset-assert-us = <1000>; reset-deassert-us = <1000>; reset-gpios = <&ioexp 4 GPIO_ACTIVE_LOW>;
@@ -146,14 +146,14 @@ #size-cells = <0>; /* Up to one PHY may be populated. */ - ethphy1f: ethernet-phy@1 { /* SMSC LAN8740Ai */ + ethphy1f: ethernet-phy@2 { /* SMSC LAN8740Ai */ compatible = "ethernet-phy-id0007.c110", "ethernet-phy-ieee802.3-c22"; interrupt-parent = <&gpio4>; interrupts = <3 IRQ_TYPE_LEVEL_LOW>; pinctrl-0 = <&pinctrl_ethphy1>; pinctrl-names = "default"; - reg = <1>; + reg = <2>; reset-assert-us = <1000>; reset-deassert-us = <1000>; reset-gpios = <&gpio4 2 GPIO_ACTIVE_LOW>;
Signature · 1 line
2.43.0
Quoted 8 lines · Marek Vasut
Enable PCA953x GPIO expander driver in DH i.MX8MP DHCOM PDK2 configuration. The PCA9539 GPIO expander is used on production DH i.MX8MP DHCOM SoM rev.200. This is already enabled in DH i.MX8MP DHCOM PDK3 configuration so align the two configurations.
Fixes 9de599ec3d59 ("arm64: dts: imx8mp: Update i.MX8MP DHCOM SoM DT to production rev.200")Signed-off-by Marek Vasut <[email protected]>
Applied both, thanks.