arm64: dts: qcom: sa8775p-ride: support both board variants

index ec1c10a12470..000037f4a712 100644
@@ -895,6 +895,7 @@ properties:
       - items:
           - enum:
               - qcom,sa8775p-ride
+              - qcom,sa8775p-ride-r3
           - const: qcom,sa8775p
 
       - items:

index 26ad05bd3b3f..2e87fd760dbd 100644
@@ -5,835 +5,43 @@
 
 /dts-v1/;
 
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
-
-#include "sa8775p.dtsi"
-#include "sa8775p-pmics.dtsi"
+#include "sa8775p-ride.dtsi"
 
 / {
 	model = "Qualcomm SA8775P Ride";
 	compatible = "qcom,sa8775p-ride", "qcom,sa8775p";
-
-	aliases {
-		ethernet0 = &ethernet0;
-		ethernet1 = &ethernet1;
-		i2c11 = &i2c11;
-		i2c18 = &i2c18;
-		serial0 = &uart10;
-		serial1 = &uart12;
-		serial2 = &uart17;
-		spi16 = &spi16;
-		ufshc1 = &ufs_mem_hc;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-};
-
-&apps_rsc {
-	regulators-0 {
-		compatible = "qcom,pmm8654au-rpmh-regulators";
-		qcom,pmic-id = "a";
-
-		vreg_s4a: smps4 {
-			regulator-name = "vreg_s4a";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1816000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_s5a: smps5 {
-			regulator-name = "vreg_s5a";
-			regulator-min-microvolt = <1850000>;
-			regulator-max-microvolt = <1996000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_s9a: smps9 {
-			regulator-name = "vreg_s9a";
-			regulator-min-microvolt = <535000>;
-			regulator-max-microvolt = <1120000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l4a: ldo4 {
-			regulator-name = "vreg_l4a";
-			regulator-min-microvolt = <788000>;
-			regulator-max-microvolt = <1050000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-allow-set-load;
-			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
-						   RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l5a: ldo5 {
-			regulator-name = "vreg_l5a";
-			regulator-min-microvolt = <870000>;
-			regulator-max-microvolt = <950000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-allow-set-load;
-			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
-						   RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l6a: ldo6 {
-			regulator-name = "vreg_l6a";
-			regulator-min-microvolt = <870000>;
-			regulator-max-microvolt = <970000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-allow-set-load;
-			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
-						   RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l7a: ldo7 {
-			regulator-name = "vreg_l7a";
-			regulator-min-microvolt = <720000>;
-			regulator-max-microvolt = <950000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-allow-set-load;
-			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
-						   RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l8a: ldo8 {
-			regulator-name = "vreg_l8a";
-			regulator-min-microvolt = <2504000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-allow-set-load;
-			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
-						   RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l9a: ldo9 {
-			regulator-name = "vreg_l9a";
-			regulator-min-microvolt = <2970000>;
-			regulator-max-microvolt = <3544000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-allow-set-load;
-			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
-						   RPMH_REGULATOR_MODE_HPM>;
-		};
-	};
-
-	regulators-1 {
-		compatible = "qcom,pmm8654au-rpmh-regulators";
-		qcom,pmic-id = "c";
-
-		vreg_l1c: ldo1 {
-			regulator-name = "vreg_l1c";
-			regulator-min-microvolt = <1140000>;
-			regulator-max-microvolt = <1260000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-allow-set-load;
-			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
-						   RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l2c: ldo2 {
-			regulator-name = "vreg_l2c";
-			regulator-min-microvolt = <900000>;
-			regulator-max-microvolt = <1100000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-allow-set-load;
-			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
-						   RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l3c: ldo3 {
-			regulator-name = "vreg_l3c";
-			regulator-min-microvolt = <1100000>;
-			regulator-max-microvolt = <1300000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-allow-set-load;
-			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
-						   RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l4c: ldo4 {
-			regulator-name = "vreg_l4c";
-			regulator-min-microvolt = <1200000>;
-			regulator-max-microvolt = <1200000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			/*
-			 * FIXME: This should have regulator-allow-set-load but
-			 * we're getting an over-current fault from the PMIC
-			 * when switching to LPM.
-			 */
-		};
-
-		vreg_l5c: ldo5 {
-			regulator-name = "vreg_l5c";
-			regulator-min-microvolt = <1100000>;
-			regulator-max-microvolt = <1300000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-allow-set-load;
-			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
-						   RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l6c: ldo6 {
-			regulator-name = "vreg_l6c";
-			regulator-min-microvolt = <1620000>;
-			regulator-max-microvolt = <1980000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-allow-set-load;
-			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
-						   RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l7c: ldo7 {
-			regulator-name = "vreg_l7c";
-			regulator-min-microvolt = <1620000>;
-			regulator-max-microvolt = <2000000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-allow-set-load;
-			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
-						   RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l8c: ldo8 {
-			regulator-name = "vreg_l8c";
-			regulator-min-microvolt = <2400000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-allow-set-load;
-			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
-						   RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l9c: ldo9 {
-			regulator-name = "vreg_l9c";
-			regulator-min-microvolt = <1650000>;
-			regulator-max-microvolt = <2700000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-allow-set-load;
-			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
-						   RPMH_REGULATOR_MODE_HPM>;
-		};
-	};
-
-	regulators-2 {
-		compatible = "qcom,pmm8654au-rpmh-regulators";
-		qcom,pmic-id = "e";
-
-		vreg_s4e: smps4 {
-			regulator-name = "vreg_s4e";
-			regulator-min-microvolt = <970000>;
-			regulator-max-microvolt = <1520000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_s7e: smps7 {
-			regulator-name = "vreg_s7e";
-			regulator-min-microvolt = <1010000>;
-			regulator-max-microvolt = <1170000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_s9e: smps9 {
-			regulator-name = "vreg_s9e";
-			regulator-min-microvolt = <300000>;
-			regulator-max-microvolt = <570000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l6e: ldo6 {
-			regulator-name = "vreg_l6e";
-			regulator-min-microvolt = <1280000>;
-			regulator-max-microvolt = <1450000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-allow-set-load;
-			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
-						   RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l8e: ldo8 {
-			regulator-name = "vreg_l8e";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1950000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-allow-set-load;
-			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
-						   RPMH_REGULATOR_MODE_HPM>;
-		};
-	};
 };
 
 &ethernet0 {
 	phy-mode = "sgmii";
-	phy-handle = <&sgmii_phy0>;
-
-	pinctrl-0 = <&ethernet0_default>;
-	pinctrl-names = "default";
-
-	snps,mtl-rx-config = <&mtl_rx_setup>;
-	snps,mtl-tx-config = <&mtl_tx_setup>;
-	snps,ps-speed = <1000>;
-
-	status = "okay";
-
-	mdio {
-		compatible = "snps,dwmac-mdio";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		sgmii_phy0: phy@8 {
-			compatible = "ethernet-phy-id0141.0dd4";
-			reg = <0x8>;
-			device_type = "ethernet-phy";
-			interrupts-extended = <&tlmm 7 IRQ_TYPE_EDGE_FALLING>;
-			reset-gpios = <&pmm8654au_2_gpios 8 GPIO_ACTIVE_LOW>;
-			reset-assert-us = <11000>;
-			reset-deassert-us = <70000>;
-		};
-
-		sgmii_phy1: phy@a {
-			compatible = "ethernet-phy-id0141.0dd4";
-			reg = <0xa>;
-			device_type = "ethernet-phy";
-			interrupts-extended = <&tlmm 26 IRQ_TYPE_EDGE_FALLING>;
-			reset-gpios = <&pmm8654au_2_gpios 9 GPIO_ACTIVE_LOW>;
-			reset-assert-us = <11000>;
-			reset-deassert-us = <70000>;
-		};
-	};
-
-	mtl_rx_setup: rx-queues-config {
-		snps,rx-queues-to-use = <4>;
-		snps,rx-sched-sp;
-
-		queue0 {
-			snps,dcb-algorithm;
-			snps,map-to-dma-channel = <0x0>;
-			snps,route-up;
-			snps,priority = <0x1>;
-		};
-
-		queue1 {
-			snps,dcb-algorithm;
-			snps,map-to-dma-channel = <0x1>;
-			snps,route-ptp;
-		};
-
-		queue2 {
-			snps,avb-algorithm;
-			snps,map-to-dma-channel = <0x2>;
-			snps,route-avcp;
-		};
-
-		queue3 {
-			snps,avb-algorithm;
-			snps,map-to-dma-channel = <0x3>;
-			snps,priority = <0xc>;
-		};
-	};
-
-	mtl_tx_setup: tx-queues-config {
-		snps,tx-queues-to-use = <4>;
-		snps,tx-sched-sp;
-
-		queue0 {
-			snps,dcb-algorithm;
-		};
-
-		queue1 {
-			snps,dcb-algorithm;
-		};
-
-		queue2 {
-			snps,avb-algorithm;
-			snps,send_slope = <0x1000>;
-			snps,idle_slope = <0x1000>;
-			snps,high_credit = <0x3e800>;
-			snps,low_credit = <0xffc18000>;
-		};
-
-		queue3 {
-			snps,avb-algorithm;
-			snps,send_slope = <0x1000>;
-			snps,idle_slope = <0x1000>;
-			snps,high_credit = <0x3e800>;
-			snps,low_credit = <0xffc18000>;
-		};
-	};
 };
 
 &ethernet1 {
 	phy-mode = "sgmii";
-	phy-handle = <&sgmii_phy1>;
+};
 
-	snps,mtl-rx-config = <&mtl_rx_setup1>;
-	snps,mtl-tx-config = <&mtl_tx_setup1>;
-	snps,ps-speed = <1000>;
+&mdio {
+	compatible = "snps,dwmac-mdio";
+	#address-cells = <1>;
+	#size-cells = <0>;
 
-	status = "okay";
-
-	mtl_rx_setup1: rx-queues-config {
-		snps,rx-queues-to-use = <4>;
-		snps,rx-sched-sp;
-
-		queue0 {
-			snps,dcb-algorithm;
-			snps,map-to-dma-channel = <0x0>;
-			snps,route-up;
-			snps,priority = <0x1>;
-		};
-
-		queue1 {
-			snps,dcb-algorithm;
-			snps,map-to-dma-channel = <0x1>;
-			snps,route-ptp;
-		};
-
-		queue2 {
-			snps,avb-algorithm;
-			snps,map-to-dma-channel = <0x2>;
-			snps,route-avcp;
-		};
-
-		queue3 {
-			snps,avb-algorithm;
-			snps,map-to-dma-channel = <0x3>;
-			snps,priority = <0xc>;
-		};
+	sgmii_phy0: phy@8 {
+		compatible = "ethernet-phy-id0141.0dd4";
+		reg = <0x8>;
+		device_type = "ethernet-phy";
+		interrupts-extended = <&tlmm 7 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&pmm8654au_2_gpios 8 GPIO_ACTIVE_LOW>;
+		reset-assert-us = <11000>;
+		reset-deassert-us = <70000>;
 	};
 
-	mtl_tx_setup1: tx-queues-config {
-		snps,tx-queues-to-use = <4>;
-		snps,tx-sched-sp;
-
-		queue0 {
-			snps,dcb-algorithm;
-		};
-
-		queue1 {
-			snps,dcb-algorithm;
-		};
-
-		queue2 {
-			snps,avb-algorithm;
-			snps,send_slope = <0x1000>;
-			snps,idle_slope = <0x1000>;
-			snps,high_credit = <0x3e800>;
-			snps,low_credit = <0xffc18000>;
-		};
-
-		queue3 {
-			snps,avb-algorithm;
-			snps,send_slope = <0x1000>;
-			snps,idle_slope = <0x1000>;
-			snps,high_credit = <0x3e800>;
-			snps,low_credit = <0xffc18000>;
-		};
+	sgmii_phy1: phy@a {
+		compatible = "ethernet-phy-id0141.0dd4";
+		reg = <0xa>;
+		device_type = "ethernet-phy";
+		interrupts-extended = <&tlmm 26 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&pmm8654au_2_gpios 9 GPIO_ACTIVE_LOW>;
+		reset-assert-us = <11000>;
+		reset-deassert-us = <70000>;
 	};
 };
-
-&i2c11 {
-	clock-frequency = <400000>;
-	pinctrl-0 = <&qup_i2c11_default>;
-	pinctrl-names = "default";
-	status = "okay";
-};
-
-&i2c18 {
-	clock-frequency = <400000>;
-	pinctrl-0 = <&qup_i2c18_default>;
-	pinctrl-names = "default";
-	status = "okay";
-};
-
-&pmm8654au_0_gpios {
-	gpio-line-names = "DS_EN",
-			  "POFF_COMPLETE",
-			  "UFS0_VER_ID",
-			  "FAST_POFF",
-			  "DBU1_PON_DONE",
-			  "AOSS_SLEEP",
-			  "CAM_DES0_EN",
-			  "CAM_DES1_EN",
-			  "CAM_DES2_EN",
-			  "CAM_DES3_EN",
-			  "UEFI",
-			  "ANALOG_PON_OPT";
-};
-
-&pmm8654au_0_pon_resin {
-	linux,code = <KEY_VOLUMEDOWN>;
-	status = "okay";
-};
-
-&pmm8654au_1_gpios {
-	gpio-line-names = "PMIC_C_ID0",
-			  "PMIC_C_ID1",
-			  "UFS1_VER_ID",
-			  "IPA_PWR",
-			  "",
-			  "WLAN_DBU4_EN",
-			  "WLAN_EN",
-			  "BT_EN",
-			  "USB2_PWR_EN",
-			  "USB2_FAULT";
-
-	usb2_en_state: usb2-en-state {
-		pins = "gpio9";
-		function = "normal";
-		output-high;
-		power-source = <0>;
-	};
-};
-
-&pmm8654au_2_gpios {
-	gpio-line-names = "PMIC_E_ID0",
-			  "PMIC_E_ID1",
-			  "USB0_PWR_EN",
-			  "USB0_FAULT",
-			  "SENSOR_IRQ_1",
-			  "SENSOR_IRQ_2",
-			  "SENSOR_RST",
-			  "SGMIIO0_RST",
-			  "SGMIIO1_RST",
-			  "USB1_PWR_ENABLE",
-			  "USB1_FAULT",
-			  "VMON_SPX8";
-
-	usb0_en_state: usb0-en-state {
-		pins = "gpio3";
-		function = "normal";
-		output-high;
-		power-source = <0>;
-	};
-
-	usb1_en_state: usb1-en-state {
-		pins = "gpio10";
-		function = "normal";
-		output-high;
-		power-source = <0>;
-	};
-};
-
-&pmm8654au_3_gpios {
-	gpio-line-names = "PMIC_G_ID0",
-			  "PMIC_G_ID1",
-			  "GNSS_RST",
-			  "GNSS_EN",
-			  "GNSS_BOOT_MODE";
-};
-
-&qupv3_id_1 {
-	status = "okay";
-};
-
-&qupv3_id_2 {
-	status = "okay";
-};
-
-&serdes0 {
-	phy-supply = <&vreg_l5a>;
-	status = "okay";
-};
-
-&serdes1 {
-	phy-supply = <&vreg_l5a>;
-	status = "okay";
-};
-
-&sleep_clk {
-	clock-frequency = <32764>;
-};
-
-&spi16 {
-	pinctrl-0 = <&qup_spi16_default>;
-	pinctrl-names = "default";
-	status = "okay";
-};
-
-&tlmm {
-	ethernet0_default: ethernet0-default-state {
-		ethernet0_mdc: ethernet0-mdc-pins {
-			pins = "gpio8";
-			function = "emac0_mdc";
-			drive-strength = <16>;
-			bias-pull-up;
-		};
-
-		ethernet0_mdio: ethernet0-mdio-pins {
-			pins = "gpio9";
-			function = "emac0_mdio";
-			drive-strength = <16>;
-			bias-pull-up;
-		};
-	};
-
-	qup_uart10_default: qup-uart10-state {
-		pins = "gpio46", "gpio47";
-		function = "qup1_se3";
-	};
-
-	qup_spi16_default: qup-spi16-state {
-		pins = "gpio86", "gpio87", "gpio88", "gpio89";
-		function = "qup2_se2";
-		drive-strength = <6>;
-		bias-disable;
-	};
-
-	qup_i2c11_default: qup-i2c11-state {
-		pins = "gpio48", "gpio49";
-		function = "qup1_se4";
-		drive-strength = <2>;
-		bias-pull-up;
-	};
-
-	qup_i2c18_default: qup-i2c18-state {
-		pins = "gpio95", "gpio96";
-		function = "qup2_se4";
-		drive-strength = <2>;
-		bias-pull-up;
-	};
-
-	qup_uart12_default: qup-uart12-state {
-		qup_uart12_cts: qup-uart12-cts-pins {
-			pins = "gpio52";
-			function = "qup1_se5";
-			bias-disable;
-		};
-
-		qup_uart12_rts: qup-uart12-rts-pins {
-			pins = "gpio53";
-			function = "qup1_se5";
-			bias-pull-down;
-		};
-
-		qup_uart12_tx: qup-uart12-tx-pins {
-			pins = "gpio54";
-			function = "qup1_se5";
-			bias-pull-up;
-		};
-
-		qup_uart12_rx: qup-uart12-rx-pins {
-			pins = "gpio55";
-			function = "qup1_se5";
-			bias-pull-down;
-		};
-	};
-
-	qup_uart17_default: qup-uart17-state {
-		qup_uart17_cts: qup-uart17-cts-pins {
-			pins = "gpio91";
-			function = "qup2_se3";
-			bias-disable;
-		};
-
-		qup_uart17_rts: qup0-uart17-rts-pins {
-			pins = "gpio92";
-			function = "qup2_se3";
-			bias-pull-down;
-		};
-
-		qup_uart17_tx: qup0-uart17-tx-pins {
-			pins = "gpio93";
-			function = "qup2_se3";
-			bias-pull-up;
-		};
-
-		qup_uart17_rx: qup0-uart17-rx-pins {
-			pins = "gpio94";
-			function = "qup2_se3";
-			bias-pull-down;
-		};
-	};
-
-	pcie0_default_state: pcie0-default-state {
-		perst-pins {
-			pins = "gpio2";
-			function = "gpio";
-			drive-strength = <2>;
-			bias-pull-down;
-		};
-
-		clkreq-pins {
-			pins = "gpio1";
-			function = "pcie0_clkreq";
-			drive-strength = <2>;
-			bias-pull-up;
-		};
-
-		wake-pins {
-			pins = "gpio0";
-			function = "gpio";
-			drive-strength = <2>;
-			bias-pull-up;
-		};
-	};
-
-	pcie1_default_state: pcie1-default-state {
-		perst-pins {
-			pins = "gpio4";
-			function = "gpio";
-			drive-strength = <2>;
-			bias-pull-down;
-		};
-
-		clkreq-pins {
-			pins = "gpio3";
-			function = "pcie1_clkreq";
-			drive-strength = <2>;
-			bias-pull-up;
-		};
-
-		wake-pins {
-			pins = "gpio5";
-			function = "gpio";
-			drive-strength = <2>;
-			bias-pull-up;
-		};
-	};
-};
-
-&pcie0 {
-	perst-gpios = <&tlmm 2 GPIO_ACTIVE_LOW>;
-	wake-gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&pcie0_default_state>;
-
-	status = "okay";
-};
-
-&pcie1 {
-	perst-gpios = <&tlmm 4 GPIO_ACTIVE_LOW>;
-	wake-gpios = <&tlmm 5 GPIO_ACTIVE_HIGH>;
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&pcie1_default_state>;
-
-	status = "okay";
-};
-
-&pcie0_phy {
-	vdda-phy-supply = <&vreg_l5a>;
-	vdda-pll-supply = <&vreg_l1c>;
-
-	status = "okay";
-};
-
-&pcie1_phy {
-	vdda-phy-supply = <&vreg_l5a>;
-	vdda-pll-supply = <&vreg_l1c>;
-
-	status = "okay";
-};
-
-&uart10 {
-	compatible = "qcom,geni-debug-uart";
-	pinctrl-0 = <&qup_uart10_default>;
-	pinctrl-names = "default";
-	status = "okay";
-};
-
-&uart12 {
-	pinctrl-0 = <&qup_uart12_default>;
-	pinctrl-names = "default";
-	status = "okay";
-};
-
-&uart17 {
-	pinctrl-0 = <&qup_uart17_default>;
-	pinctrl-names = "default";
-	status = "okay";
-};
-
-&ufs_mem_hc {
-	reset-gpios = <&tlmm 149 GPIO_ACTIVE_LOW>;
-	vcc-supply = <&vreg_l8a>;
-	vcc-max-microamp = <1100000>;
-	vccq-supply = <&vreg_l4c>;
-	vccq-max-microamp = <1200000>;
-
-	status = "okay";
-};
-
-&ufs_mem_phy {
-	vdda-phy-supply = <&vreg_l4a>;
-	vdda-pll-supply = <&vreg_l1c>;
-
-	status = "okay";
-};
-
-&usb_0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&usb0_en_state>;
-
-	status = "okay";
-};
-
-&usb_0_dwc3 {
-	dr_mode = "peripheral";
-};
-
-&usb_0_hsphy {
-	vdda-pll-supply = <&vreg_l7a>;
-	vdda18-supply = <&vreg_l6c>;
-	vdda33-supply = <&vreg_l9a>;
-
-	status = "okay";
-};
-
-&usb_0_qmpphy {
-	vdda-phy-supply = <&vreg_l1c>;
-	vdda-pll-supply = <&vreg_l7a>;
-
-	status = "okay";
-};
-
-&usb_1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&usb1_en_state>;
-
-	status = "okay";
-};
-
-&usb_1_dwc3 {
-	dr_mode = "host";
-};
-
-&usb_1_hsphy {
-	vdda-pll-supply = <&vreg_l7a>;
-	vdda18-supply = <&vreg_l6c>;
-	vdda33-supply = <&vreg_l9a>;
-
-	status = "okay";
-};
-
-&usb_1_qmpphy {
-	vdda-phy-supply = <&vreg_l1c>;
-	vdda-pll-supply = <&vreg_l7a>;
-
-	status = "okay";
-};
-
-&usb_2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&usb2_en_state>;
-
-	status = "okay";
-};
-
-&usb_2_dwc3 {
-	dr_mode = "host";
-};
-
-&usb_2_hsphy {
-	vdda-pll-supply = <&vreg_l7a>;
-	vdda18-supply = <&vreg_l6c>;
-	vdda33-supply = <&vreg_l9a>;
-
-	status = "okay";
-};
-
-&xo_board_clk {
-	clock-frequency = <38400000>;
-};

814 lines not on this page · raw message

index 5576c7d6ea06..8b7a81b82213 100644
@@ -113,6 +113,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= sa8155p-adp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sa8295p-adp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sa8540p-ride.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sa8775p-ride.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sa8775p-ride-r3.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-acer-aspire1.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-idp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-coachz-r1.dtb

47 lines not on this page · raw message