Skip to contentSkip to conversation

PowerPC: Replace kretprobe with rethook

PATCH Superseded Abhishek Dubey 3 participants 5 messages Jun 27, 2024 – Jul 9, 2024 PowerPC

v3 of 4 Superseded Latest is v4 →

lore
Share & tools
lore
#0 lore raw

PATCH v3 1/1 PowerPC: Replace kretprobe with rethook

This is an adaptation of commit f3a112c0c40d ("x86,rethook,kprobes:
Replace kretprobe with rethook on x86") to PowerPC.

Replaces the kretprobe code with rethook on Power. With this patch, kretprobe on Power uses the rethook instead of kretprobe specific trampoline code.

Reference to other archs:
commit b57c2f124098 ("riscv: add riscv rethook implementation") commit 7b0a096436c2 ("LoongArch: Replace kretprobe with rethook")

---

Changes in v3:
* Fixing return address moved to arch_rethook_fixup_return()
* Addressed other minor comments
* show_stack mods to show correct fn name to go in separate patch

---
 arch/powerpc/Kconfig             |  1 +
 arch/powerpc/kernel/Makefile     |  1 +
 arch/powerpc/kernel/kprobes.c    | 65 +--------------------------
 arch/powerpc/kernel/optprobes.c  |  2 +-
 arch/powerpc/kernel/rethook.c    | 77 ++++++++++++++++++++++++++++++++
 arch/powerpc/kernel/stacktrace.c |  6 ++-
 6 files changed, 85 insertions(+), 67 deletions(-)
 create mode 100644 arch/powerpc/kernel/rethook.c
arch/powerpc/Kconfig +1 -0
index c88c6d46a5bc..fa0b1ab3f935 100644
@@ -270,6 +270,7 @@ config PPC
 	select HAVE_PERF_EVENTS_NMI		if PPC64
 	select HAVE_PERF_REGS
 	select HAVE_PERF_USER_STACK_DUMP
+	select HAVE_RETHOOK
 	select HAVE_REGS_AND_STACK_ACCESS_API
 	select HAVE_RELIABLE_STACKTRACE
 	select HAVE_RSEQ
arch/powerpc/kernel/Makefile +1 -0
index 8585d03c02d3..7dd1b523b17f 100644
@@ -140,6 +140,7 @@ obj-$(CONFIG_KPROBES)		+= kprobes.o
 obj-$(CONFIG_OPTPROBES)		+= optprobes.o optprobes_head.o
 obj-$(CONFIG_KPROBES_ON_FTRACE)	+= kprobes-ftrace.o
 obj-$(CONFIG_UPROBES)		+= uprobes.o
+obj-$(CONFIG_RETHOOK)           += rethook.o
 obj-$(CONFIG_PPC_UDBG_16550)	+= legacy_serial.o udbg_16550.o
 obj-$(CONFIG_SWIOTLB)		+= dma-swiotlb.o
 obj-$(CONFIG_ARCH_HAS_DMA_SET_MASK) += dma-mask.o
arch/powerpc/kernel/kprobes.c +1 -64

85 lines not on this page · raw message

arch/powerpc/kernel/optprobes.c +1 -1
index 004fae2044a3..c0b351d61058 100644
@@ -56,7 +56,7 @@ static unsigned long can_optimize(struct kprobe *p)
 	 * has a 'nop' instruction, which can be emulated.
 	 * So further checks can be skipped.
 	 */
-	if (p->addr == (kprobe_opcode_t *)&__kretprobe_trampoline)
+	if (p->addr == (kprobe_opcode_t *)&arch_rethook_trampoline)
 		return addr + sizeof(kprobe_opcode_t);
 
 	/*
arch/powerpc/kernel/rethook.c new file +77 -0

77 lines not on this page · raw message

arch/powerpc/kernel/stacktrace.c +4 -2
index e6a958a5da27..90882b5175cd 100644
@@ -21,6 +21,7 @@
 #include <asm/processor.h>
 #include <linux/ftrace.h>
 #include <asm/kprobes.h>
+#include <linux/rethook.h>
 
 #include <asm/paca.h>
 
@@ -133,12 +134,13 @@ int __no_sanitize_address arch_stack_walk_reliable(stack_trace_consume_fn consum
 		 * arch-dependent code, they are generic.
 		 */
 		ip = ftrace_graph_ret_addr(task, &graph_idx, ip, stack);
-#ifdef CONFIG_KPROBES
+
 		/*
 		 * Mark stacktraces with kretprobed functions on them
 		 * as unreliable.
 		 */
-		if (ip == (unsigned long)__kretprobe_trampoline)
+#ifdef CONFIG_RETHOOK
+		if (ip == (unsigned long)arch_rethook_trampoline)
 			return -EINVAL;
 #endif
 
Signature · 1 line
2.44.0
Reviewed-by on v3 1/1
#1 lore raw

Hi Abhishek,
This patch looks good to me, except for one main change in trampoline_rethook_handler().

Other than that, I have a few more minor comments. Sorry, I should have caught that last time. But, the other change needs a new submission, so good to get these addressed as well.

For the subject, we generally use 'powerpc' (all lowercase):
powerpc: Replace kretprobe with rethook

Quoted 2 lines · Abhishek Dubey

This is an adaptation of commit f3a112c0c40d ("x86,rethook,kprobes:
Replace kretprobe with rethook on x86") to PowerPC.

					     ^^^^^^^

Here too.

Quoted 4 lines

Replaces the kretprobe code with rethook on Power. With this patch, kretprobe on Power uses the rethook instead of kretprobe specific trampoline code.

In general, it is good to describe what is being done in the patch. So, rather than 'Replaces', you can start that with 'Replace kretprobe code with rethook on powerpc.'

The second sentence also looks redundant. It is good if you can describe what the patch does where possible. For instance:
Rethook follows the existing kretprobe implementation, but separates it from kprobes so that it can be used by fprobe (ftrace-based function entry/exit probes). As such, this patch also enables fprobe to work on powerpc. The only other change compared to the existing kretprobe implementation is doing the return address fixup in arch_rethook_fixup_return().

Quoted 180 lines

Reference to other archs:
commit b57c2f124098 ("riscv: add riscv rethook implementation") commit 7b0a096436c2 ("LoongArch: Replace kretprobe with rethook")

---

Changes in v3:
* Fixing return address moved to arch_rethook_fixup_return()
* Addressed other minor comments
* show_stack mods to show correct fn name to go in separate patch

---
 arch/powerpc/Kconfig             |  1 +
 arch/powerpc/kernel/Makefile     |  1 +
 arch/powerpc/kernel/kprobes.c    | 65 +--------------------------
 arch/powerpc/kernel/optprobes.c  |  2 +-
 arch/powerpc/kernel/rethook.c    | 77 ++++++++++++++++++++++++++++++++
 arch/powerpc/kernel/stacktrace.c |  6 ++-
 6 files changed, 85 insertions(+), 67 deletions(-)
 create mode 100644 arch/powerpc/kernel/rethook.c
arch/powerpc/Kconfig +1 -0
index c88c6d46a5bc..fa0b1ab3f935 100644
@@ -270,6 +270,7 @@ config PPC
 	select HAVE_PERF_EVENTS_NMI		if PPC64
 	select HAVE_PERF_REGS
 	select HAVE_PERF_USER_STACK_DUMP
+	select HAVE_RETHOOK
 	select HAVE_REGS_AND_STACK_ACCESS_API
 	select HAVE_RELIABLE_STACKTRACE
 	select HAVE_RSEQ
arch/powerpc/kernel/Makefile +1 -0
index 8585d03c02d3..7dd1b523b17f 100644
@@ -140,6 +140,7 @@ obj-$(CONFIG_KPROBES)		+= kprobes.o
 obj-$(CONFIG_OPTPROBES)		+= optprobes.o optprobes_head.o
 obj-$(CONFIG_KPROBES_ON_FTRACE)	+= kprobes-ftrace.o
 obj-$(CONFIG_UPROBES)		+= uprobes.o
+obj-$(CONFIG_RETHOOK)           += rethook.o
 obj-$(CONFIG_PPC_UDBG_16550)	+= legacy_serial.o udbg_16550.o
 obj-$(CONFIG_SWIOTLB)		+= dma-swiotlb.o
 obj-$(CONFIG_ARCH_HAS_DMA_SET_MASK) += dma-mask.o
arch/powerpc/kernel/kprobes.c +1 -64
index 14c5ddec3056..f8aa91bc3b17 100644
@@ -228,16 +228,6 @@ static nokprobe_inline void set_current_kprobe(struct kprobe *p, struct pt_regs
 	kcb->kprobe_saved_msr = regs->msr;
 }
 
-void arch_prepare_kretprobe(struct kretprobe_instance *ri, struct pt_regs *regs)
-{
-	ri->ret_addr = (kprobe_opcode_t *)regs->link;
-	ri->fp = NULL;
-
-	/* Replace the return addr with trampoline addr */
-	regs->link = (unsigned long)__kretprobe_trampoline;
-}
-NOKPROBE_SYMBOL(arch_prepare_kretprobe);
-
 static int try_to_emulate(struct kprobe *p, struct pt_regs *regs)
 {
 	int ret;
@@ -394,49 +384,6 @@ int kprobe_handler(struct pt_regs *regs)
 }
 NOKPROBE_SYMBOL(kprobe_handler);
 
-/*
- * Function return probe trampoline:
- * 	- init_kprobes() establishes a probepoint here
- * 	- When the probed function returns, this probe
- * 		causes the handlers to fire
- */
-asm(".global __kretprobe_trampoline\n"
-	".type __kretprobe_trampoline, @function\n"
-	"__kretprobe_trampoline:\n"
-	"nop\n"
-	"blr\n"
-	".size __kretprobe_trampoline, .-__kretprobe_trampoline\n");
-
-/*
- * Called when the probe at kretprobe trampoline is hit
- */
-static int trampoline_probe_handler(struct kprobe *p, struct pt_regs *regs)
-{
-	unsigned long orig_ret_address;
-
-	orig_ret_address = __kretprobe_trampoline_handler(regs, NULL);
-	/*
-	 * We get here through one of two paths:
-	 * 1. by taking a trap -> kprobe_handler() -> here
-	 * 2. by optprobe branch -> optimized_callback() -> opt_pre_handler() -> here
-	 *
-	 * When going back through (1), we need regs->nip to be setup properly
-	 * as it is used to determine the return address from the trap.
-	 * For (2), since nip is not honoured with optprobes, we instead setup
-	 * the link register properly so that the subsequent 'blr' in
-	 * __kretprobe_trampoline jumps back to the right instruction.
-	 *
-	 * For nip, we should set the address to the previous instruction since
-	 * we end up emulating it in kprobe_handler(), which increments the nip
-	 * again.
-	 */
-	regs_set_return_ip(regs, orig_ret_address - 4);
-	regs->link = orig_ret_address;
-
-	return 0;
-}
-NOKPROBE_SYMBOL(trampoline_probe_handler);
-
 /*
  * Called after single-stepping.  p->addr is the address of the
  * instruction whose first byte has been replaced by the "breakpoint"
@@ -539,19 +486,9 @@ int kprobe_fault_handler(struct pt_regs *regs, int trapnr)
 }
 NOKPROBE_SYMBOL(kprobe_fault_handler);
 
-static struct kprobe trampoline_p = {
-	.addr = (kprobe_opcode_t *) &__kretprobe_trampoline,
-	.pre_handler = trampoline_probe_handler
-};
-
-int __init arch_init_kprobes(void)
-{
-	return register_kprobe(&trampoline_p);
-}
-
 int arch_trampoline_kprobe(struct kprobe *p)
 {
-	if (p->addr == (kprobe_opcode_t *)&__kretprobe_trampoline)
+	if (p->addr == (kprobe_opcode_t *)&arch_rethook_trampoline)
 		return 1;
 
 	return 0;
arch/powerpc/kernel/optprobes.c +1 -1
index 004fae2044a3..c0b351d61058 100644
@@ -56,7 +56,7 @@ static unsigned long can_optimize(struct kprobe *p)
 	 * has a 'nop' instruction, which can be emulated.
 	 * So further checks can be skipped.
 	 */
-	if (p->addr == (kprobe_opcode_t *)&__kretprobe_trampoline)
+	if (p->addr == (kprobe_opcode_t *)&arch_rethook_trampoline)
 		return addr + sizeof(kprobe_opcode_t);
 
 	/*
arch/powerpc/kernel/rethook.c new file +22 -0
new file mode 100644
index 000000000000..d2453793ea5d
@@ -0,0 +1,77 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * PowerPC implementation of rethook. This depends on kprobes.
+ */
+
+#include <linux/kprobes.h>
+#include <linux/rethook.h>
+
+/*
+ * Function return trampoline:
+ *     - init_kprobes() establishes a probepoint here
+ *     - When the probed function returns, this probe
+ *         causes the handlers to fire
+ */
+asm(".global arch_rethook_trampoline\n"
+	".type arch_rethook_trampoline, @function\n"
+	"arch_rethook_trampoline:\n"
+	"nop\n"
+	"blr\n"
+	".size arch_rethook_trampoline, .-arch_rethook_trampoline\n");
+
+/*

arch/powerpc/kernel/rethook.c line 32

Quoted 10 lines
arch/powerpc/kernel/rethook.c new file +10 -0
+ * Called when the probe at kretprobe trampoline is hit
+ */
+static int trampoline_rethook_handler(struct kprobe *p, struct pt_regs *regs)
+{
+	unsigned long orig_ret_address;
+
+	orig_ret_address = rethook_trampoline_handler(regs, 0);
+	rethook_trampoline_handler(regs, orig_ret_address);
+	return 0;
+}

I think we should pass in regs->gpr[1] to allow it to be verified against the stack pointer we saved on function entry. This can be simplified to:

static int trampoline_rethook_handler(struct kprobe *p, struct pt_regs *regs)

{
	return !rethook_trampoline_handler(regs, regs->gpr[1]);
}

I have tested this patch with that change. So, with that change included:

Quoted 15 lines
arch/powerpc/kernel/rethook.c new file +15 -0
+NOKPROBE_SYMBOL(trampoline_rethook_handler);
+
+void arch_rethook_prepare(struct rethook_node *rh, struct pt_regs *regs, bool mcount)
+{
+	rh->ret_addr = regs->link;
+	rh->frame = regs->gpr[1];
+
+	/* Replace the return addr with trampoline addr */
+	regs->link = (unsigned long)arch_rethook_trampoline;
+}
+NOKPROBE_SYMBOL(arch_rethook_prepare);
+
+/* This is called from rethook_trampoline_handler(). */
+void arch_rethook_fixup_return(struct pt_regs *regs, unsigned long orig_ret_address)
+{

arch/powerpc/kernel/rethook.c line 57

Quoted 10 lines
arch/powerpc/kernel/rethook.c new file +10 -0
+	/*
+	 * We get here through one of two paths:
+	 * 1. by taking a trap -> kprobe_handler() -> here
+	 * 2. by optprobe branch -> optimized_callback() -> opt_pre_handler() -> here
+	 *
+	 * When going back through (1), we need regs->nip to be setup properly
+	 * as it is used to determine the return address from the trap.
+	 * For (2), since nip is not honoured with optprobes, we instead setup
+	 * the link register properly so that the subsequent 'blr' in
+	 * __kretprobe_trampoline jumps back to the right instruction.
	  ^^^^^^^^^^^^^^^^^^^^^^^
	  arch_rethook_trampoline

Thanks!
- Naveen

Quoted 51 lines
arch/powerpc/kernel/rethook.c new file +20 -0
+	 *
+	 * For nip, we should set the address to the previous instruction since
+	 * we end up emulating it in kprobe_handler(), which increments the nip
+	 * again.
+	 */
+	regs_set_return_ip(regs, orig_ret_address - 4);
+	regs->link = orig_ret_address;
+}
+NOKPROBE_SYMBOL(arch_rethook_fixup_return);
+
+static struct kprobe trampoline_p = {
+	.addr = (kprobe_opcode_t *) &arch_rethook_trampoline,
+	.pre_handler = trampoline_rethook_handler
+};
+
+/* rethook initializer */
+int __init arch_init_kprobes(void)
+{
+	return register_kprobe(&trampoline_p);
+}
arch/powerpc/kernel/stacktrace.c +4 -2
index e6a958a5da27..90882b5175cd 100644
@@ -21,6 +21,7 @@
 #include <asm/processor.h>
 #include <linux/ftrace.h>
 #include <asm/kprobes.h>
+#include <linux/rethook.h>
 
 #include <asm/paca.h>
 
@@ -133,12 +134,13 @@ int __no_sanitize_address arch_stack_walk_reliable(stack_trace_consume_fn consum
 		 * arch-dependent code, they are generic.
 		 */
 		ip = ftrace_graph_ret_addr(task, &graph_idx, ip, stack);
-#ifdef CONFIG_KPROBES
+
 		/*
 		 * Mark stacktraces with kretprobed functions on them
 		 * as unreliable.
 		 */
-		if (ip == (unsigned long)__kretprobe_trampoline)
+#ifdef CONFIG_RETHOOK
+		if (ip == (unsigned long)arch_rethook_trampoline)
 			return -EINVAL;
 #endif
 
Signature · 1 line
2.44.0
#2 lore raw
In reply to Abhishek Dubey

arch/powerpc/kernel/rethook.c line 77

Quoted 5 lines · On Thu, 27 Jun 2024 09:21:01 -0400 Abhishek Dubey <[email protected]> wrote:
arch/powerpc/kernel/rethook.c new file +5 -0
+/* rethook initializer */
+int __init arch_init_kprobes(void)
+{
+	return register_kprobe(&trampoline_p);
+}

No, please don't use arch_init_kprobes() for initializing rethook, since rethook is used from fprobe too (at this moment).

If you want to make it relays on kprobes, you have to make a dependency in powerpc's kconfig, e.g.

select HAVE_RETHOOK if KPROBES

But I don't recommend it.

Thank you,

Signature · 1 line
Masami Hiramatsu (Google) <[email protected]>
#3 lore raw
Quoted 12 lines · Masami Hiramatsu

arch/powerpc/kernel/rethook.c line 77

Quoted 5 lines · On Thu, 27 Jun 2024 09:21:01 -0400 Abhishek Dubey <[email protected]> wrote:
arch/powerpc/kernel/rethook.c new file +5 -0
+/* rethook initializer */
+int __init arch_init_kprobes(void)
+{
+	return register_kprobe(&trampoline_p);
+}

No, please don't use arch_init_kprobes() for initializing rethook, since rethook is used from fprobe too (at this moment).

Quoted 6 lines

If you want to make it relays on kprobes, you have to make a dependency in powerpc's kconfig, e.g.

select HAVE_RETHOOK if KPROBES

But I don't recommend it.

Given that kretprobe has always worked this way on powerpc, I think this is a fair tradeoff. We get to enable fprobes on powerpc only if kprobes is also enabled.

Longer term, it would certainly be nice to get rid of that probe, and to expand the trampoline to directly invoke the rethook callback.

Thanks,
Naveen

#4 lore raw
Quoted 18 lines · On Tue, 09 Jul 2024 12:28:29 +0530 Naveen N Rao <[email protected]> wrote:
Quoted 17 lines · Masami Hiramatsu

arch/powerpc/kernel/rethook.c line 77

Quoted 5 lines · On Thu, 27 Jun 2024 09:21:01 -0400 Abhishek Dubey <[email protected]> wrote:
arch/powerpc/kernel/rethook.c new file +5 -0
+/* rethook initializer */
+int __init arch_init_kprobes(void)
+{
+	return register_kprobe(&trampoline_p);
+}

No, please don't use arch_init_kprobes() for initializing rethook, since rethook is used from fprobe too (at this moment).

If you want to make it relays on kprobes, you have to make a dependency in powerpc's kconfig, e.g.

select HAVE_RETHOOK if KPROBES

Quoted 8 lines
Quoted 1 line

But I don't recommend it.

Given that kretprobe has always worked this way on powerpc, I think this is a fair tradeoff. We get to enable fprobes on powerpc only if kprobes is also enabled.

Longer term, it would certainly be nice to get rid of that probe, and to expand the trampoline to directly invoke the rethook callback.

OK. In longer term, rethook will be only for kretprobe, and kretprobe will be replaced by fprobe[1]. So please comment it and add that

[1] https://lore.kernel.org/all/172000134410.63468.13742222887213469474.stgit@devnote2/

Thank you,

Quoted 4 lines

Thanks,
Naveen

Signature · 1 line
Masami Hiramatsu (Google) <[email protected]>