arm64: dts: imx8mp: Update Fast ethernet PHY MDIO addresses to match DH i.MX8MP DHCOM rev.200
Subsystems (3)
PATCH v2 1/1 arm64: dts: imx8mp: Update Fast ethernet PHY MDIO addresses to match DH i.MX8MP DHCOM rev.200
The production DH i.MX8MP DHCOM SoM rev.200 uses updated PHY MDIO addresses for the Fast ethernet PHYs. Update the base SoM DT to cater for this change. Prototype rev.100 SoM was never publicly available and was manufactured in limited series, anything currently available is rev.200 or newer, so it is safe to update the DT this way.
---
Cc: Andrew Lunn <[email protected]>
Cc: Conor Dooley <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Krzysztof Kozlowski <[email protected]>
Cc: Pengutronix Kernel Team <[email protected]>
Cc: Rob Herring <[email protected]>
Cc: Sascha Hauer <[email protected]>
Cc: Shawn Guo <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
---
V2: Update the commit message, rev.100 SoM was a prototype that is not available
--- arch/arm64/boot/dts/freescale/imx8mp-dhcom-som.dtsi | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-)
arch/arm64/boot/dts/freescale/imx8mp-dhcom-som.dtsi +4 -4
@@ -110,14 +110,14 @@ mdio { #size-cells = <0>; /* Up to one of these two PHYs may be populated. */ - ethphy0f: ethernet-phy@0 { /* SMSC LAN8740Ai */ + ethphy0f: ethernet-phy@1 { /* SMSC LAN8740Ai */ compatible = "ethernet-phy-id0007.c110", "ethernet-phy-ieee802.3-c22"; interrupt-parent = <&gpio3>; interrupts = <19 IRQ_TYPE_LEVEL_LOW>; pinctrl-0 = <&pinctrl_ethphy0>; pinctrl-names = "default"; - reg = <0>; + reg = <1>; reset-assert-us = <1000>; reset-deassert-us = <1000>; reset-gpios = <&ioexp 4 GPIO_ACTIVE_LOW>;
@@ -156,14 +156,14 @@ mdio { #size-cells = <0>; /* Up to one PHY may be populated. */ - ethphy1f: ethernet-phy@1 { /* SMSC LAN8740Ai */ + ethphy1f: ethernet-phy@2 { /* SMSC LAN8740Ai */ compatible = "ethernet-phy-id0007.c110", "ethernet-phy-ieee802.3-c22"; interrupt-parent = <&gpio4>; interrupts = <3 IRQ_TYPE_LEVEL_LOW>; pinctrl-0 = <&pinctrl_ethphy1>; pinctrl-names = "default"; - reg = <1>; + reg = <2>; reset-assert-us = <1000>; reset-deassert-us = <1000>; reset-gpios = <&gpio4 2 GPIO_ACTIVE_LOW>;
Signature · 1 line
2.43.0
Quoted 10 lines
Subject: [PATCH v2] arm64: dts: imx8mp: Update Fast ethernet PHY MDIO addresses to match DH i.MX8MP DHCOM rev.200
The production DH i.MX8MP DHCOM SoM rev.200 uses updated PHY MDIO addresses for the Fast ethernet PHYs. Update the base SoM DT to cater for this change.
Prototype rev.100 SoM was never publicly available and was manufactured in limited series, anything currently available is rev.200 or newer, so it is safe to update the DT this way.
Quoted 2 lines
Signed-off-by Marek Vasut <[email protected]>---
Andrew Lunn
Reviewed-byQuoted 10 lines · Peng Fan
Quoted 10 lines
Subject: [PATCH v2] arm64: dts: imx8mp: Update Fast ethernet PHY MDIO addresses to match DH i.MX8MP DHCOM rev.200
The production DH i.MX8MP DHCOM SoM rev.200 uses updated PHY MDIO addresses for the Fast ethernet PHYs. Update the base SoM DT to cater for this change.
Prototype rev.100 SoM was never publicly available and was manufactured in limited series, anything currently available is rev.200 or newer, so it is safe to update the DT this way.
Quoted 4 lines
Quoted 2 lines
Signed-off-by Marek Vasut <[email protected]>---
Reviewed-by Peng Fan <[email protected]>
Andrew
Shawn Guo
AppliedQuoted 7 lines · Marek Vasut
The production DH i.MX8MP DHCOM SoM rev.200 uses updated PHY MDIO addresses for the Fast ethernet PHYs. Update the base SoM DT to cater for this change. Prototype rev.100 SoM was never publicly available and was manufactured in limited series, anything currently available is rev.200 or newer, so it is safe to update the DT this way.
Signed-off-by Marek Vasut <[email protected]>
Applied, thanks!