Skip to contentSkip to conversation

ARM: dts: stm32: Add ethernet support for DH STM32MP13xx DHCOR DHSBC board

PATCH In review Marek Vasut 2 participants 3 messages Jun 28, 2024 – Jun 30, 2024

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH v2 1/1 ARM: dts: stm32: Add ethernet support for DH STM32MP13xx DHCOR DHSBC board

Add ethernet support for the DH STM32MP13xx DHCOR DHSBC carrier board. This carrier board is populated with two gigabit ethernet ports and two Realtek RTL8211F PHYs, both are described in this DT patch.

---
Cc: Alexandre Torgue <[email protected]>
Cc: Christophe Roullier <[email protected]>
Cc: Conor Dooley <[email protected]>
Cc: Krzysztof Kozlowski <[email protected]>
Cc: Maxime Coquelin <[email protected]>
Cc: Rob Herring <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
---
V2: Fold ARM: dts: stm32: Add phandle to nvmem efuse into STM32MP13xx ethernet
DT node into this patch and make the nvmem-cells/nvmem-cell-names specific to this board

---
 .../boot/dts/st/stm32mp135f-dhcor-dhsbc.dts   | 60 +++++++++++++++++++
 1 file changed, 60 insertions(+)
arch/arm/boot/dts/st/stm32mp135f-dhcor-dhsbc.dts +60 -0
index 5f4f6b6e427a5..3cc9ad88d61bc 100644
@@ -22,6 +22,8 @@ / {
 		     "st,stm32mp135";
 
 	aliases {
+		ethernet0 = &ethernet1;
+		ethernet1 = &ethernet2;
 		serial2 = &usart1;
 		serial3 = &usart2;
 	};
@@ -72,6 +74,64 @@ channel@12 {
 	};
 };
 
+&ethernet1 {
+	nvmem-cell-names = "mac-address";
+	nvmem-cells = <&ethernet_mac1_address>;
+	phy-handle = <&ethphy1>;
+	phy-mode = "rgmii-id";
+	pinctrl-0 = <&eth1_rgmii_pins_a>;
+	pinctrl-1 = <&eth1_rgmii_sleep_pins_a>;
+	pinctrl-names = "default", "sleep";
+	st,ext-phyclk;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+
+		ethphy1: ethernet-phy@1 {
+			/* RTL8211F */
+			compatible = "ethernet-phy-id001c.c916";
+			interrupt-parent = <&gpiog>;
+			interrupts = <12 IRQ_TYPE_LEVEL_LOW>;
+			reg = <1>;
+			reset-assert-us = <15000>;
+			reset-deassert-us = <55000>;
+			reset-gpios = <&gpioa 11 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&ethernet2 {
+	nvmem-cell-names = "mac-address";
+	nvmem-cells = <&ethernet_mac2_address>;
+	phy-handle = <&ethphy2>;
+	phy-mode = "rgmii-id";
+	pinctrl-0 = <&eth2_rgmii_pins_a>;
+	pinctrl-1 = <&eth2_rgmii_sleep_pins_a>;
+	pinctrl-names = "default", "sleep";
+	st,ext-phyclk;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+
+		ethphy2: ethernet-phy@1 {
+			/* RTL8211F */
+			compatible = "ethernet-phy-id001c.c916";
+			interrupt-parent = <&gpiog>;
+			interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
+			reg = <1>;
+			reset-assert-us = <15000>;
+			reset-deassert-us = <55000>;
+			reset-gpios = <&gpiog 8 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
 &gpioa {
 	gpio-line-names = "", "", "", "",
 			  "", "DHSBC_USB_PWR_CC1", "", "",
Signature · 1 line
2.43.0
maintainer
#1 lore raw

Hi Marek

Quoted 5 lines · Marek Vasut

Add ethernet support for the DH STM32MP13xx DHCOR DHSBC carrier board. This carrier board is populated with two gigabit ethernet ports and two Realtek RTL8211F PHYs, both are described in this DT patch.

I already applied series which add the ETH support in mp13 DH board. Can you please resend a patch which only add the nvmem efuse stuff please ?

Alex

Quoted 97 lines

---
Cc: Alexandre Torgue <[email protected]>
Cc: Christophe Roullier <[email protected]>
Cc: Conor Dooley <[email protected]>
Cc: Krzysztof Kozlowski <[email protected]>
Cc: Maxime Coquelin <[email protected]>
Cc: Rob Herring <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
---
V2: Fold ARM: dts: stm32: Add phandle to nvmem efuse into STM32MP13xx ethernet
DT node into this patch and make the nvmem-cells/nvmem-cell-names specific to this board

---
  .../boot/dts/st/stm32mp135f-dhcor-dhsbc.dts   | 60 +++++++++++++++++++
  1 file changed, 60 insertions(+)
arch/arm/boot/dts/st/stm32mp135f-dhcor-dhsbc.dts +60 -0
index 5f4f6b6e427a5..3cc9ad88d61bc 100644
@@ -22,6 +22,8 @@ / {
  		     "st,stm32mp135";
 
  	aliases {
+		ethernet0 = &ethernet1;
+		ethernet1 = &ethernet2;
  		serial2 = &usart1;
  		serial3 = &usart2;
  	};
@@ -72,6 +74,64 @@ channel@12 {
  	};
  };
 
+&ethernet1 {
+	nvmem-cell-names = "mac-address";
+	nvmem-cells = <&ethernet_mac1_address>;
+	phy-handle = <&ethphy1>;
+	phy-mode = "rgmii-id";
+	pinctrl-0 = <&eth1_rgmii_pins_a>;
+	pinctrl-1 = <&eth1_rgmii_sleep_pins_a>;
+	pinctrl-names = "default", "sleep";
+	st,ext-phyclk;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+
+		ethphy1: ethernet-phy@1 {
+			/* RTL8211F */
+			compatible = "ethernet-phy-id001c.c916";
+			interrupt-parent = <&gpiog>;
+			interrupts = <12 IRQ_TYPE_LEVEL_LOW>;
+			reg = <1>;
+			reset-assert-us = <15000>;
+			reset-deassert-us = <55000>;
+			reset-gpios = <&gpioa 11 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&ethernet2 {
+	nvmem-cell-names = "mac-address";
+	nvmem-cells = <&ethernet_mac2_address>;
+	phy-handle = <&ethphy2>;
+	phy-mode = "rgmii-id";
+	pinctrl-0 = <&eth2_rgmii_pins_a>;
+	pinctrl-1 = <&eth2_rgmii_sleep_pins_a>;
+	pinctrl-names = "default", "sleep";
+	st,ext-phyclk;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+
+		ethphy2: ethernet-phy@1 {
+			/* RTL8211F */
+			compatible = "ethernet-phy-id001c.c916";
+			interrupt-parent = <&gpiog>;
+			interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
+			reg = <1>;
+			reset-assert-us = <15000>;
+			reset-deassert-us = <55000>;
+			reset-gpios = <&gpiog 8 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
  &gpioa {
  	gpio-line-names = "", "", "", "",
  			  "", "DHSBC_USB_PWR_CC1", "", "",
#2 lore raw
Quoted 1 line · Alexandre TORGUE

Hi Marek

Hi,

Quoted 8 lines · Marek Vasut
Quoted 5 lines

Add ethernet support for the DH STM32MP13xx DHCOR DHSBC carrier board. This carrier board is populated with two gigabit ethernet ports and two Realtek RTL8211F PHYs, both are described in this DT patch.

I already applied series which add the ETH support in mp13 DH board. Can you please resend a patch which only add the nvmem efuse stuff please ?

Done in [PATCH] ARM: dts: stm32: Add ethernet MAC nvmem cells to DH STM32MP13xx DHCOR DHSBC board .