Timeout error with Microchip OTPC driver on SAM9X60
Subsystems (4)
cover Timeout error with Microchip OTPC driver on SAM9X60
Hei hei,
on a custom sam9x60 based board we want to access a unique ID of the SoC. Microchip sam-ba has a command 'readuniqueid' which returns the content of the OTPC Product UID x Register in that case.
(On a different board with a SAMA5D2 we use the Serial Number x Register exposed through the atmel soc driver, which is not present in the SAM9X60 series.)
There is a driver for the OTPC of the SAMA7G5 and after comparing register layouts it seems that one is almost identical to the one used by SAM9X60. So I thought just adapting the driver for SAM9X60 should be easy. (At least as a start, the driver has no support for that UID register, but I suppose it would be the right place to implement it.)
However it does not work. I used the patch attached with additional debug messages on a SAM9X60-Curiosity board. (That patch is not meant for inclusion, just for showing what I've tried.)
On probe the function mchp_otpc_init_packets_list() returns with ETIMEDOUT, which it can only do if mchp_otpc_prepare_read() returns with timeout and that can only happen if read_poll_timeout() times out on reading the Status Register. Poking that register with devmem 0xeff0000c 32 gives 0x00000040 which means "A packet read is on-going".
Kinda stuck here. Any ideas?
Greets and have a nice weekend everyone
Alex
Alexander Dahl (1):
nvmem: microchip-otpc: Add support for SAM9X60
.../dts/microchip/at91-sam9x60_curiosity.dts | 4 ++++ arch/arm/boot/dts/microchip/sam9x60.dtsi | 7 +++++++ drivers/nvmem/microchip-otpc.c | 16 +++++++++++++--- 3 files changed, 24 insertions(+), 3 deletions(-)
base-commit: fec50db7033ea478773b159e0e2efb135270e3b7
Signature · 7 lines
2.39.2 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
RFC PATCH 1/1 nvmem: microchip-otpc: Add support for SAM9X60
--- .../dts/microchip/at91-sam9x60_curiosity.dts | 4 ++++ arch/arm/boot/dts/microchip/sam9x60.dtsi | 7 +++++++ drivers/nvmem/microchip-otpc.c | 16 +++++++++++++--- 3 files changed, 24 insertions(+), 3 deletions(-)
arch/arm/boot/dts/microchip/at91-sam9x60_curiosity.dts +4 -0
@@ -254,6 +254,10 @@ ethernet-phy@0 { }; }; +&otpc { + status = "okay"; +}; + &pinctrl { adc { pinctrl_adc_default: adc-default {
arch/arm/boot/dts/microchip/sam9x60.dtsi +7 -0
@@ -156,6 +156,13 @@ sdmmc1: sdio-host@90000000 { status = "disabled"; }; + otpc: efuse@eff00000 { + compatible = "microchip,sam9x60-otpc", "syscon"; + reg = <0xeff00000 0xec>; + #address-cells = <1>; + #size-cells = <1>; + }; + apb { compatible = "simple-bus"; #address-cells = <1>;
drivers/nvmem/microchip-otpc.c +13 -3
@@ -8,6 +8,7 @@*/ #include <linux/bitfield.h> +#include <linux/dev_printk.h> #include <linux/iopoll.h> #include <linux/module.h> #include <linux/nvmem-provider.h>
@@ -248,29 +249,38 @@ static int mchp_otpc_probe(struct platform_device *pdev)int ret; otpc =devm_kzalloc (&pdev->dev,sizeof (*otpc),GFP_KERNEL ); -if (!otpc) +if (!otpc) { +dev_err (&pdev->dev,"devm_kzalloc() error\n" );return -ENOMEM ; + } otpc->base =devm_platform_ioremap_resource (pdev,0 ); -if (IS_ERR (otpc->base)) +if (IS_ERR (otpc->base)) { +dev_err (&pdev->dev,"devm_platform_ioremap_resource() error\n" );return PTR_ERR (otpc->base); + } otpc->dev = &pdev->dev; ret =mchp_otpc_init_packets_list (otpc, &size); -if (ret) +if (ret) { +dev_err (&pdev->dev,"mchp_otpc_init_packets_list() error (%d)\n" , ret);return ret; + } mchp_nvmem_config.dev = otpc->dev; mchp_nvmem_config.add_legacy_fixed_of_cells = true; mchp_nvmem_config.size = size; mchp_nvmem_config.priv = otpc; nvmem =devm_nvmem_register (&pdev->dev, &mchp_nvmem_config); +if (!nvmem) +dev_err (&pdev->dev,"devm_nvmem_register() error\n" );return PTR_ERR_OR_ZERO (nvmem); }static const struct of_device_id __maybe_unused mchp_otpc_ids[] = { { .compatible ="microchip,sama7g5-otpc" , }, + { .compatible ="microchip,sam9x60-otpc" , }, { }, };MODULE_DEVICE_TABLE (of, mchp_otpc_ids);
Signature · 7 lines
2.39.2 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
claudiu beznea
maintainerHi, Alexander,
Quoted 20 lines · Alexander Dahl
Hei hei,
on a custom sam9x60 based board we want to access a unique ID of the SoC. Microchip sam-ba has a command 'readuniqueid' which returns the content of the OTPC Product UID x Register in that case.
(On a different board with a SAMA5D2 we use the Serial Number x Register exposed through the atmel soc driver, which is not present in the SAM9X60 series.)
There is a driver for the OTPC of the SAMA7G5 and after comparing register layouts it seems that one is almost identical to the one used by SAM9X60. So I thought just adapting the driver for SAM9X60 should be easy. (At least as a start, the driver has no support for that UID register, but I suppose it would be the right place to implement it.)
However it does not work. I used the patch attached with additional debug messages on a SAM9X60-Curiosity board. (That patch is not meant for inclusion, just for showing what I've tried.)
Quoted 5 lines
On probe the function
mchp_otpc_init_packets_list()returns with ETIMEDOUT, which it can only do ifmchp_otpc_prepare_read()returns with timeout and that can only happen ifread_poll_timeout()times out on reading the Status Register. Poking that register withdevmem 0xeff0000c 32gives0x00000040which means "A packet read is on-going".
Would it be possible that the OTP memory is not properly initialized and the algorithm to initialized the packet list to confuse the hardware?
I see in the datasheet the following: "The initial value of the OTP memory is ‘0’ but the memory may contain some “defective” bits already set to the value ‘1’."
Otherwise, from the top of my mind I don't have any idea on what might happen.
Thank you,
Claudiu Beznea
Quoted 16 lines
Kinda stuck here. Any ideas?
Greets and have a nice weekend everyone
AlexAlexander Dahl (1):
nvmem: microchip-otpc: Add support for SAM9X60.../dts/microchip/at91-sam9x60_curiosity.dts | 4 ++++ arch/arm/boot/dts/microchip/sam9x60.dtsi | 7 +++++++ drivers/nvmem/microchip-otpc.c | 16 +++++++++++++--- 3 files changed, 24 insertions(+), 3 deletions(-)base-commit:
fec50db7033ea478773b159e0e2efb135270e3b7
Hei hei,
Am Wed, Apr 24, 2024 at 10:32:02AM +0300 schrieb claudiu beznea:
Quoted 30 lines
Hi, Alexander,
Quoted 20 lines · Alexander Dahl
Hei hei,
on a custom sam9x60 based board we want to access a unique ID of the SoC. Microchip sam-ba has a command 'readuniqueid' which returns the content of the OTPC Product UID x Register in that case.
(On a different board with a SAMA5D2 we use the Serial Number x Register exposed through the atmel soc driver, which is not present in the SAM9X60 series.)
There is a driver for the OTPC of the SAMA7G5 and after comparing register layouts it seems that one is almost identical to the one used by SAM9X60. So I thought just adapting the driver for SAM9X60 should be easy. (At least as a start, the driver has no support for that UID register, but I suppose it would be the right place to implement it.)
However it does not work. I used the patch attached with additional debug messages on a SAM9X60-Curiosity board. (That patch is not meant for inclusion, just for showing what I've tried.)
Quoted 5 lines
On probe the function
mchp_otpc_init_packets_list()returns with ETIMEDOUT, which it can only do ifmchp_otpc_prepare_read()returns with timeout and that can only happen ifread_poll_timeout()times out on reading the Status Register. Poking that register withdevmem 0xeff0000c 32gives0x00000040which means "A packet read is on-going".
Quoted 6 lines
Would it be possible that the OTP memory is not properly initialized and the algorithm to initialized the packet list to confuse the hardware?
I see in the datasheet the following: "The initial value of the OTP memory is ‘0’ but the memory may contain some “defective” bits already set to the value ‘1’."
Meanwhile we looked deeper into this driver. I just drop here what we found so far, because it's vacation time, and this will probably not be picked up again this month because vacation etc. I wanna get it out of my head for now. ;-)
Note: most of this should also apply to sama7g5, from comparing data sheets the OTPC is the same.
1. the call to read_poll_timeout() most probably has its sleep and timeout paramaters swapped.
2. the read access to OTPC_CR register is not necessary, the datasheet says the register is "write only". It may even trigger an interrupt for reading a write only register. Furthermore the WPCTEN bit in the OTPC Write Protection Mode register (OTPC_WPMR) is not checked before accessing OTPC_CR as suggested by the datasheet.
3. the errata sheet for the SAM9X60 SoC (DS80000846) has a section on the OTPC which recommends a fixup before the first write operation, with code example:
https://ww1.microchip.com/downloads/aemDocuments/documents/MPU32/ProductDocuments/Errata/SAM9X60-Device-Silicon-Errata-and-Data-Sheet-Clarif-DS80000846.pdf
The same thing is implemented in 'atmel-software-package' which has (at least had in the past) the code for the binary applets used in the 'sam-ba' tool:
https://github.com/atmelcorp/atmel-software-package/blame/master/drivers/nvm/otp/otpc.c#L86
I bet this fixup should be implemented in this driver here as well?
So far for now.
Greets
Alex
Quoted 27 lines
Otherwise, from the top of my mind I don't have any idea on what might happen.
Thank you,
Claudiu BezneaQuoted 9 lines
Kinda stuck here. Any ideas?
Greets and have a nice weekend everyone
AlexAlexander Dahl (1):
nvmem: microchip-otpc: Add support for SAM9X60Quoted 7 lines
.../dts/microchip/at91-sam9x60_curiosity.dts | 4 ++++ arch/arm/boot/dts/microchip/sam9x60.dtsi | 7 +++++++ drivers/nvmem/microchip-otpc.c | 16 +++++++++++++--- 3 files changed, 24 insertions(+), 3 deletions(-)base-commit:
fec50db7033ea478773b159e0e2efb135270e3b7_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Hello Claudiu,
Am Wed, Apr 24, 2024 at 10:32:02AM +0300 schrieb claudiu beznea:
Quoted 30 lines
Hi, Alexander,
Quoted 20 lines · Alexander Dahl
Hei hei,
on a custom sam9x60 based board we want to access a unique ID of the SoC. Microchip sam-ba has a command 'readuniqueid' which returns the content of the OTPC Product UID x Register in that case.
(On a different board with a SAMA5D2 we use the Serial Number x Register exposed through the atmel soc driver, which is not present in the SAM9X60 series.)
There is a driver for the OTPC of the SAMA7G5 and after comparing register layouts it seems that one is almost identical to the one used by SAM9X60. So I thought just adapting the driver for SAM9X60 should be easy. (At least as a start, the driver has no support for that UID register, but I suppose it would be the right place to implement it.)
However it does not work. I used the patch attached with additional debug messages on a SAM9X60-Curiosity board. (That patch is not meant for inclusion, just for showing what I've tried.)
Quoted 5 lines
On probe the function
mchp_otpc_init_packets_list()returns with ETIMEDOUT, which it can only do ifmchp_otpc_prepare_read()returns with timeout and that can only happen ifread_poll_timeout()times out on reading the Status Register. Poking that register withdevmem 0xeff0000c 32gives0x00000040which means "A packet read is on-going".
Quoted 6 lines
Would it be possible that the OTP memory is not properly initialized and the algorithm to initialized the packet list to confuse the hardware?
I see in the datasheet the following: "The initial value of the OTP memory is ‘0’ but the memory may contain some “defective” bits already set to the value ‘1’."
I think this might be possible? SAM-BA also stumbles here, but the SoC is like shipped by the vendor, no OTPC writes ever from my side. When calling this …
$ sam-ba -p serial -d sam9x60:0:1 -t 5 -a bootconfig -c readcfg:bcp-otp
… I get this on serial debug output:
Applet 'BootConfig' from SAM-BA Applets Framework 3.8 (v3.8). -E- Cannot read Boot Config Packet.
-E- Invalid parameter for read config: index 0
Question is: how should the driver behave in this case? Fail like it does now? Or load in some kind of safe state with "empty" nvmem? This is especially interesting with regard to a new question below.
Quoted 1 line
Otherwise, from the top of my mind I don't have any idea on what might happen.
I have some debug code here, and digging deeper into this currently to see what's really happening. While at it, a new question came up:
There's this OTP memory which the driver tries to expose as NVMEM. However what I really want to do is getting access to the OTPC Product UID x Registers, which are not OTP memory but plain registers inside of the address space of the OTPC here. Should this be exposed as a second nvmem device then, or handled by a different driver? How would accessing the same register space from different drivers be handled then?
Greets
Alex
Quoted 25 lines
Thank you,
Claudiu BezneaQuoted 9 lines
Kinda stuck here. Any ideas?
Greets and have a nice weekend everyone
AlexAlexander Dahl (1):
nvmem: microchip-otpc: Add support for SAM9X60Quoted 7 lines
.../dts/microchip/at91-sam9x60_curiosity.dts | 4 ++++ arch/arm/boot/dts/microchip/sam9x60.dtsi | 7 +++++++ drivers/nvmem/microchip-otpc.c | 16 +++++++++++++--- 3 files changed, 24 insertions(+), 3 deletions(-)base-commit:
fec50db7033ea478773b159e0e2efb135270e3b7_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
claudiu beznea
maintainerHi, Alexander,
Quoted 36 lines · Alexander Dahl
Hello Claudiu,
Am Wed, Apr 24, 2024 at 10:32:02AM +0300 schrieb claudiu beznea:
Quoted 33 lines
Hi, Alexander,
Quoted 20 lines · Alexander Dahl
Hei hei,
on a custom sam9x60 based board we want to access a unique ID of the SoC. Microchip sam-ba has a command 'readuniqueid' which returns the content of the OTPC Product UID x Register in that case.
(On a different board with a SAMA5D2 we use the Serial Number x Register exposed through the atmel soc driver, which is not present in the SAM9X60 series.)
There is a driver for the OTPC of the SAMA7G5 and after comparing register layouts it seems that one is almost identical to the one used by SAM9X60. So I thought just adapting the driver for SAM9X60 should be easy. (At least as a start, the driver has no support for that UID register, but I suppose it would be the right place to implement it.)
However it does not work. I used the patch attached with additional debug messages on a SAM9X60-Curiosity board. (That patch is not meant for inclusion, just for showing what I've tried.)
Quoted 5 lines
On probe the function
mchp_otpc_init_packets_list()returns with ETIMEDOUT, which it can only do ifmchp_otpc_prepare_read()returns with timeout and that can only happen ifread_poll_timeout()times out on reading the Status Register. Poking that register withdevmem 0xeff0000c 32gives0x00000040which means "A packet read is on-going".Would it be possible that the OTP memory is not properly initialized and the algorithm to initialized the packet list to confuse the hardware?
Quoted 6 lines
Quoted 3 lines
I see in the datasheet the following: "The initial value of the OTP memory is ‘0’ but the memory may contain some “defective” bits already set to the value ‘1’."
I think this might be possible? SAM-BA also stumbles here, but the SoC is like shipped by the vendor, no OTPC writes ever from my side.
I'm not sure how the SAM9X60 OTP memory is shipped by vendor. If I remember correctly the user must flash the bootconfig packet depending on his needs.
Quoted 4 lines
When calling this …
$ sam-ba -p serial -d sam9x60:0:1 -t 5 -a bootconfig -c readcfg:bcp-otp
Quoted 8 lines
… I get this on serial debug output:
Applet 'BootConfig' from SAM-BA Applets Framework 3.8 (v3.8). -E- Cannot read Boot Config Packet.
-E- Invalid parameter for read config: index 0Question is: how should the driver behave in this case? Fail like it does now? Or load in some kind of safe state with "empty" nvmem?
The driver cannot know if the memory is defective or not. Not that I've know. It expects the memory to be in a proper state.
E.g. On SAMA7G5 the OTP memory has at lest the temperature sensor calibration data packet. And if I remember correctly, it also has the bootconfig packet on the first position.
Thank you,
Claudiu Beznea
Quoted 43 lines
This is especially interesting with regard to a new question below.
Quoted 1 line
Otherwise, from the top of my mind I don't have any idea on what might happen.
I have some debug code here, and digging deeper into this currently to see what's really happening. While at it, a new question came up:
There's this OTP memory which the driver tries to expose as NVMEM. However what I really want to do is getting access to the OTPC Product UID x Registers, which are not OTP memory but plain registers inside of the address space of the OTPC here. Should this be exposed as a second nvmem device then, or handled by a different driver? How would accessing the same register space from different drivers be handled then?
Greets
AlexQuoted 25 lines
Thank you,
Claudiu BezneaQuoted 9 lines
Kinda stuck here. Any ideas?
Greets and have a nice weekend everyone
AlexAlexander Dahl (1):
nvmem: microchip-otpc: Add support for SAM9X60Quoted 7 lines
.../dts/microchip/at91-sam9x60_curiosity.dts | 4 ++++ arch/arm/boot/dts/microchip/sam9x60.dtsi | 7 +++++++ drivers/nvmem/microchip-otpc.c | 16 +++++++++++++--- 3 files changed, 24 insertions(+), 3 deletions(-)base-commit:
fec50db7033ea478773b159e0e2efb135270e3b7_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Hello Claudiu,
Am Tue, Aug 20, 2024 at 02:59:03PM +0300 schrieb claudiu beznea:
Quoted 43 lines
Hi, Alexander,
Quoted 40 lines · Alexander Dahl
Hello Claudiu,
Am Wed, Apr 24, 2024 at 10:32:02AM +0300 schrieb claudiu beznea:
Quoted 36 lines
Hi, Alexander,
Quoted 20 lines · Alexander Dahl
Hei hei,
on a custom sam9x60 based board we want to access a unique ID of the SoC. Microchip sam-ba has a command 'readuniqueid' which returns the content of the OTPC Product UID x Register in that case.
(On a different board with a SAMA5D2 we use the Serial Number x Register exposed through the atmel soc driver, which is not present in the SAM9X60 series.)
There is a driver for the OTPC of the SAMA7G5 and after comparing register layouts it seems that one is almost identical to the one used by SAM9X60. So I thought just adapting the driver for SAM9X60 should be easy. (At least as a start, the driver has no support for that UID register, but I suppose it would be the right place to implement it.)
However it does not work. I used the patch attached with additional debug messages on a SAM9X60-Curiosity board. (That patch is not meant for inclusion, just for showing what I've tried.)
Quoted 5 lines
On probe the function
mchp_otpc_init_packets_list()returns with ETIMEDOUT, which it can only do ifmchp_otpc_prepare_read()returns with timeout and that can only happen ifread_poll_timeout()times out on reading the Status Register. Poking that register withdevmem 0xeff0000c 32gives0x00000040which means "A packet read is on-going".Would it be possible that the OTP memory is not properly initialized and the algorithm to initialized the packet list to confuse the hardware?
I see in the datasheet the following: "The initial value of the OTP memory is ‘0’ but the memory may contain some “defective” bits already set to the value ‘1’."
Quoted 5 lines
Quoted 2 lines
I think this might be possible? SAM-BA also stumbles here, but the SoC is like shipped by the vendor, no OTPC writes ever from my side.
I'm not sure how the SAM9X60 OTP memory is shipped by vendor. If I remember correctly the user must flash the bootconfig packet depending on his needs.
User can do that, but does not need to if the defaults are sufficient. On sam9x60-curiosity it just boots with defaults from SD card or raw NAND flash. No bootconfig packets are set here.
Quoted 10 lines
Quoted 10 lines
When calling this …
$ sam-ba -p serial -d sam9x60:0:1 -t 5 -a bootconfig -c readcfg:bcp-otp… I get this on serial debug output:
Applet 'BootConfig' from SAM-BA Applets Framework 3.8 (v3.8). -E- Cannot read Boot Config Packet.
-E- Invalid parameter for read config: index 0
Quoted 5 lines
Quoted 2 lines
Question is: how should the driver behave in this case? Fail like it does now? Or load in some kind of safe state with "empty" nvmem?
The driver cannot know if the memory is defective or not. Not that I've know. It expects the memory to be in a proper state.
Datasheet says:
After each reset, the OTPC parses the User area to check its content. The header of each packet will be read, depending on the header value some actions can be triggered:
• If the header is corrupted, the init sequence is interrupted and the OTPC_ISR.COERR bit is set.
The COERR bit in OTPC_ISR can be checked in the driver of course. Not sure if that adds any real value however. Maybe issue a warning in that case?
Quoted 3 lines
E.g. On SAMA7G5 the OTP memory has at lest the temperature sensor calibration data packet. And if I remember correctly, it also has the bootconfig packet on the first position.
Nice to know, however I don't have a board featuring the sama7g5 at hand.
Greets
Alex
Quoted 48 lines
Thank you,
Claudiu BezneaQuoted 43 lines
This is especially interesting with regard to a new question below.
Quoted 1 line
Otherwise, from the top of my mind I don't have any idea on what might happen.
I have some debug code here, and digging deeper into this currently to see what's really happening. While at it, a new question came up:
There's this OTP memory which the driver tries to expose as NVMEM. However what I really want to do is getting access to the OTPC Product UID x Registers, which are not OTP memory but plain registers inside of the address space of the OTPC here. Should this be exposed as a second nvmem device then, or handled by a different driver? How would accessing the same register space from different drivers be handled then?
Greets
AlexQuoted 25 lines
Thank you,
Claudiu BezneaQuoted 9 lines
Kinda stuck here. Any ideas?
Greets and have a nice weekend everyone
AlexAlexander Dahl (1):
nvmem: microchip-otpc: Add support for SAM9X60Quoted 7 lines
.../dts/microchip/at91-sam9x60_curiosity.dts | 4 ++++ arch/arm/boot/dts/microchip/sam9x60.dtsi | 7 +++++++ drivers/nvmem/microchip-otpc.c | 16 +++++++++++++--- 3 files changed, 24 insertions(+), 3 deletions(-)base-commit:
fec50db7033ea478773b159e0e2efb135270e3b7_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel