Turris Omnia MCU driver

new file mode 100644
index 000000000000..af9249695ef5
@@ -0,0 +1,86 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/firmware/cznic,turris-omnia-mcu.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: CZ.NIC's Turris Omnia MCU
+
+maintainers:
+  - Marek Behún <[email protected]>
+
+description:
+  The MCU on Turris Omnia acts as a system controller providing additional
+  GPIOs, interrupts, watchdog, system power off and wakeup configuration.
+
+properties:
+  compatible:
+    const: cznic,turris-omnia-mcu
+
+  reg:
+    description: MCU I2C slave address
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  interrupt-controller: true
+
+  '#interrupt-cells':
+    const: 2
+    description: |
+      The first cell specifies the interrupt number (0 to 63), the second cell
+      specifies interrupt type (which can be one of IRQ_TYPE_EDGE_RISING,
+      IRQ_TYPE_EDGE_FALLING or IRQ_TYPE_EDGE_BOTH).
+      The interrupt numbers correspond sequentially to GPIO numbers, taking the
+      GPIO banks into account:
+        IRQ number   GPIO bank   GPIO pin within bank
+           0 - 15      0           0 - 15
+          16 - 47      1           0 - 31
+          48 - 63      2           0 - 15
+      There are several exceptions:
+        IRQ number   meaning
+          11           LED panel brightness changed by button press
+          13           TRNG entropy ready
+          14           ECDSA message signature computation done
+
+  gpio-controller: true
+
+  '#gpio-cells':
+    const: 3
+    description:
+      The first cell is bank number (0, 1 or 2), the second cell is pin number
+      within the bank (0 to 15 for banks 0 and 2, 0 to 31 for bank 1), and the
+      third cell specifies consumer flags.
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - interrupt-controller
+  - gpio-controller
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        system-controller@2a {
+            compatible = "cznic,turris-omnia-mcu";
+            reg = <0x2a>;
+
+            interrupt-parent = <&gpio1>;
+            interrupts = <11 IRQ_TYPE_NONE>;
+
+            gpio-controller;
+            #gpio-cells = <3>;
+
+            interrupt-controller;
+            #interrupt-cells = <2>;
+        };
+    };

index 3c4fdf74a3f9..37da14d4fb4f 100644
@@ -2210,6 +2210,7 @@ F:	Documentation/ABI/testing/sysfs-bus-moxtet-devices
 F:	Documentation/ABI/testing/sysfs-firmware-turris-mox-rwtm
 F:	Documentation/devicetree/bindings/bus/moxtet.txt
 F:	Documentation/devicetree/bindings/firmware/cznic,turris-mox-rwtm.txt
+F:	Documentation/devicetree/bindings/firmware/cznic,turris-omnia-mcu.yaml
 F:	Documentation/devicetree/bindings/gpio/gpio-moxtet.txt
 F:	Documentation/devicetree/bindings/leds/cznic,turris-omnia-leds.yaml
 F:	Documentation/devicetree/bindings/watchdog/armada-37xx-wdt.txt

new file mode 100644
index 000000000000..9bc5aad00de0
@@ -0,0 +1,81 @@
+What:		/sys/bus/i2c/devices/<mcu_device>/board_revision
+Date:		September 2024
+KernelVersion:	6.11
+Contact:	Marek Behún <[email protected]>
+Description:	(RO) Contains board revision number.
+
+		Only available if board information is burned in the MCU (older
+		revisions have board information burned in the ATSHA204-A chip).
+
+		Format: %u.
+
+What:		/sys/bus/i2c/devices/<mcu_device>/first_mac_address
+Date:		September 2024
+KernelVersion:	6.11
+Contact:	Marek Behún <[email protected]>
+Description:	(RO) Contains device first MAC address. Each Turris Omnia is
+		allocated 3 MAC addresses. The two additional addresses are
+		computed from the first one by incrementing it.
+
+		Only available if board information is burned in the MCU (older
+		revisions have board information burned in the ATSHA204-A chip).
+
+		Format: %pM.
+
+What:		/sys/bus/i2c/devices/<mcu_device>/fw_features
+Date:		September 2024
+KernelVersion:	6.11
+Contact:	Marek Behún <[email protected]>
+Description:	(RO) Newer versions of the microcontroller firmware report the
+		features they support. These can be read from this file. If the
+		MCU firmware is too old, this file reads 0x0.
+
+		Format: 0x%x.
+
+What:		/sys/bus/i2c/devices/<mcu_device>/fw_version_hash_application
+Date:		September 2024
+KernelVersion:	6.11
+Contact:	Marek Behún <[email protected]>
+Description:	(RO) Contains the version hash (commit hash) of the application
+		part of the microcontroller firmware.
+
+		Format: %s.
+
+What:		/sys/bus/i2c/devices/<mcu_device>/fw_version_hash_bootloader
+Date:		September 2024
+KernelVersion:	6.11
+Contact:	Marek Behún <[email protected]>
+Description:	(RO) Contains the version hash (commit hash) of the bootloader
+		part of the microcontroller firmware.
+
+		Format: %s.
+
+What:		/sys/bus/i2c/devices/<mcu_device>/mcu_type
+Date:		September 2024
+KernelVersion:	6.11
+Contact:	Marek Behún <[email protected]>
+Description:	(RO) Contains the microcontroller type (STM32, GD32, MKL).
+
+		Format: %s.
+
+What:		/sys/bus/i2c/devices/<mcu_device>/reset_selector
+Date:		September 2024
+KernelVersion:	6.11
+Contact:	Marek Behún <[email protected]>
+Description:	(RO) Contains the selected factory reset level, determined by
+		how long the rear reset button was held by the user during board
+		reset.
+
+		Format: %i.
+
+What:		/sys/bus/i2c/devices/<mcu_device>/serial_number
+Date:		September 2024
+KernelVersion:	6.11
+Contact:	Marek Behún <[email protected]>
+Description:	(RO) Contains the 64-bit board serial number in hexadecimal
+		format.
+
+		Only available if board information is burned in the MCU (older
+		revisions have board information burned in the ATSHA204-A chip).
+
+		Format: %016X.

index 37da14d4fb4f..f35252c88463 100644
@@ -2206,6 +2206,7 @@ M:	Marek Behún <[email protected]>
 S:	Maintained
 W:	https://www.turris.cz/
 F:	Documentation/ABI/testing/debugfs-moxtet
+F:	Documentation/ABI/testing/sysfs-bus-i2c-devices-turris-omnia-mcu
 F:	Documentation/ABI/testing/sysfs-bus-moxtet-devices
 F:	Documentation/ABI/testing/sysfs-firmware-turris-mox-rwtm
 F:	Documentation/devicetree/bindings/bus/moxtet.txt

@@ -2219,10 +2220,12 @@ F:	drivers/firmware/turris-mox-rwtm.c
 F:	drivers/gpio/gpio-moxtet.c
 F:	drivers/leds/leds-turris-omnia.c
 F:	drivers/mailbox/armada-37xx-rwtm-mailbox.c
+F:	drivers/platform/cznic/
 F:	drivers/watchdog/armada_37xx_wdt.c
 F:	include/dt-bindings/bus/moxtet.h
 F:	include/linux/armada-37xx-rwtm-mailbox.h
 F:	include/linux/moxtet.h
+F:	include/linux/turris-omnia-mcu-interface.h
 
 ARM/FARADAY FA526 PORT
 M:	Hans Ulli Kroll <[email protected]>

index 81a298517df2..960fd6a82450 100644
@@ -7,6 +7,8 @@ source "drivers/platform/goldfish/Kconfig"
 
 source "drivers/platform/chrome/Kconfig"
 
+source "drivers/platform/cznic/Kconfig"
+
 source "drivers/platform/mellanox/Kconfig"
 
 source "drivers/platform/olpc/Kconfig"

index fbbe4f77aa5d..bf69cc8d7429 100644
@@ -10,5 +10,6 @@ obj-$(CONFIG_MIPS)		+= mips/
 obj-$(CONFIG_OLPC_EC)		+= olpc/
 obj-$(CONFIG_GOLDFISH)		+= goldfish/
 obj-$(CONFIG_CHROME_PLATFORMS)	+= chrome/
+obj-$(CONFIG_CZNIC_PLATFORMS)	+= cznic/
 obj-$(CONFIG_SURFACE_PLATFORMS)	+= surface/
 obj-$(CONFIG_ARM64)		+= arm64/

new file mode 100644
index 000000000000..db5f4a673d28
@@ -0,0 +1,25 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# For a description of the syntax of this configuration file,
+# see Documentation/kbuild/kconfig-language.rst.
+#
+
+menuconfig CZNIC_PLATFORMS
+	bool "Platform support for CZ.NIC's Turris hardware"
+	help
+	  Say Y here to be able to choose driver support for CZ.NIC's Turris
+	  devices. This option alone does not add any kernel code.
+
+if CZNIC_PLATFORMS
+
+config TURRIS_OMNIA_MCU
+	tristate "Turris Omnia MCU driver"
+	depends on MACH_ARMADA_38X || COMPILE_TEST
+	depends on I2C
+	help
+	  Say Y here to add support for the features implemented by the
+	  microcontroller on the CZ.NIC's Turris Omnia SOHO router.
+	  To compile this driver as a module, choose M here; the module will be
+	  called turris-omnia-mcu.
+
+endif # CZNIC_PLATFORMS

new file mode 100644
index 000000000000..31adca73bb94
@@ -0,0 +1,4 @@
+# SPDX-License-Identifier: GPL-2.0-only
+
+obj-$(CONFIG_TURRIS_OMNIA_MCU)	+= turris-omnia-mcu.o
+turris-omnia-mcu-y		:= turris-omnia-mcu-base.o

index 9bc5aad00de0..86360249080c 100644
@@ -22,6 +22,22 @@ Description:	(RO) Contains device first MAC address. Each Turris Omnia is
 
 		Format: %pM.
 
+What:		/sys/bus/i2c/devices/<mcu_device>/front_button_mode
+Date:		September 2024
+KernelVersion:	6.11
+Contact:	Marek Behún <[email protected]>
+Description:	(RW) The front button on the Turris Omnia router can be
+		configured either to change the intensity of all the LEDs on the
+		front panel, or to send the press event to the CPU as an
+		interrupt.
+
+		This file switches between these two modes:
+		- "mcu" makes the button press event be handled by the MCU to
+		  change the LEDs panel intensity.
+		- "cpu" makes the button press event be handled by the CPU.
+
+		Format: %s.
+
 What:		/sys/bus/i2c/devices/<mcu_device>/fw_features
 Date:		September 2024
 KernelVersion:	6.11

index db5f4a673d28..d95e7c83c7ae 100644
@@ -16,9 +16,24 @@ config TURRIS_OMNIA_MCU
 	tristate "Turris Omnia MCU driver"
 	depends on MACH_ARMADA_38X || COMPILE_TEST
 	depends on I2C
+	select GPIOLIB
+	select GPIOLIB_IRQCHIP
 	help
 	  Say Y here to add support for the features implemented by the
 	  microcontroller on the CZ.NIC's Turris Omnia SOHO router.
+	  The features include:
+	  - GPIO pins
+	    - to get front button press events (the front button can be
+	      configured either to generate press events to the CPU or to change
+	      front LEDs panel brightness)
+	    - to enable / disable USB port voltage regulators and to detect
+	      USB overcurrent
+	    - to detect MiniPCIe / mSATA card presence in MiniPCIe port 0
+	    - to configure resets of various peripherals on board revisions 32+
+	    - to enable / disable the VHV voltage regulator to the SOC in order
+	      to be able to program SOC's OTP on board revisions 32+
+	    - to get input from the LED output pins of the WAN ethernet PHY, LAN
+	      switch and MiniPCIe ports
 	  To compile this driver as a module, choose M here; the module will be
 	  called turris-omnia-mcu.
 

index 31adca73bb94..53fd8f1777a3 100644
@@ -2,3 +2,4 @@
 
 obj-$(CONFIG_TURRIS_OMNIA_MCU)	+= turris-omnia-mcu.o
 turris-omnia-mcu-y		:= turris-omnia-mcu-base.o
+turris-omnia-mcu-y		+= turris-omnia-mcu-gpio.o

index 86360249080c..307a55f599cb 100644
@@ -38,6 +38,22 @@ Description:	(RW) The front button on the Turris Omnia router can be
 
 		Format: %s.
 
+What:		/sys/bus/i2c/devices/<mcu_device>/front_button_poweron
+Date:		September 2024
+KernelVersion:	6.11
+Contact:	Marek Behún <[email protected]>
+Description:	(RW) Newer versions of the microcontroller firmware of the
+		Turris Omnia router support powering off the router into true
+		low power mode. The router can be powered on by pressing the
+		front button.
+
+		This file configures whether front button power on is enabled.
+
+		This file is present only if the power off feature is supported
+		by the firmware.
+
+		Format: %i.
+
 What:		/sys/bus/i2c/devices/<mcu_device>/fw_features
 Date:		September 2024
 KernelVersion:	6.11

index d95e7c83c7ae..c1e719235517 100644
@@ -18,10 +18,14 @@ config TURRIS_OMNIA_MCU
 	depends on I2C
 	select GPIOLIB
 	select GPIOLIB_IRQCHIP
+	select RTC_CLASS
 	help
 	  Say Y here to add support for the features implemented by the
 	  microcontroller on the CZ.NIC's Turris Omnia SOHO router.
 	  The features include:
+	  - board poweroff into true low power mode (with voltage regulators
+	    disabled) and the ability to configure wake up from this mode (via
+	    rtcwake)
 	  - GPIO pins
 	    - to get front button press events (the front button can be
 	      configured either to generate press events to the CPU or to change

index 53fd8f1777a3..a185ef882e44 100644
@@ -3,3 +3,4 @@
 obj-$(CONFIG_TURRIS_OMNIA_MCU)	+= turris-omnia-mcu.o
 turris-omnia-mcu-y		:= turris-omnia-mcu-base.o
 turris-omnia-mcu-y		+= turris-omnia-mcu-gpio.o
+turris-omnia-mcu-y		+= turris-omnia-mcu-sys-off-wakeup.o

index c1e719235517..e262930b3faf 100644
@@ -19,6 +19,7 @@ config TURRIS_OMNIA_MCU
 	select GPIOLIB
 	select GPIOLIB_IRQCHIP
 	select RTC_CLASS
+	select WATCHDOG_CORE
 	help
 	  Say Y here to add support for the features implemented by the
 	  microcontroller on the CZ.NIC's Turris Omnia SOHO router.

@@ -26,6 +27,7 @@ config TURRIS_OMNIA_MCU
 	  - board poweroff into true low power mode (with voltage regulators
 	    disabled) and the ability to configure wake up from this mode (via
 	    rtcwake)
+	  - MCU watchdog
 	  - GPIO pins
 	    - to get front button press events (the front button can be
 	      configured either to generate press events to the CPU or to change

index a185ef882e44..687f7718c0a1 100644
@@ -4,3 +4,4 @@ obj-$(CONFIG_TURRIS_OMNIA_MCU)	+= turris-omnia-mcu.o
 turris-omnia-mcu-y		:= turris-omnia-mcu-base.o
 turris-omnia-mcu-y		+= turris-omnia-mcu-gpio.o
 turris-omnia-mcu-y		+= turris-omnia-mcu-sys-off-wakeup.o
+turris-omnia-mcu-y		+= turris-omnia-mcu-watchdog.o

index e262930b3faf..6edac80d5fa3 100644
@@ -18,6 +18,7 @@ config TURRIS_OMNIA_MCU
 	depends on I2C
 	select GPIOLIB
 	select GPIOLIB_IRQCHIP
+	select HW_RANDOM
 	select RTC_CLASS
 	select WATCHDOG_CORE
 	help

@@ -27,6 +28,7 @@ config TURRIS_OMNIA_MCU
 	  - board poweroff into true low power mode (with voltage regulators
 	    disabled) and the ability to configure wake up from this mode (via
 	    rtcwake)
+	  - true random number generator (if available on the MCU)
 	  - MCU watchdog
 	  - GPIO pins
 	    - to get front button press events (the front button can be

index 687f7718c0a1..eae4c6b341ff 100644
@@ -4,4 +4,5 @@ obj-$(CONFIG_TURRIS_OMNIA_MCU)	+= turris-omnia-mcu.o
 turris-omnia-mcu-y		:= turris-omnia-mcu-base.o
 turris-omnia-mcu-y		+= turris-omnia-mcu-gpio.o
 turris-omnia-mcu-y		+= turris-omnia-mcu-sys-off-wakeup.o
+turris-omnia-mcu-y		+= turris-omnia-mcu-trng.o
 turris-omnia-mcu-y		+= turris-omnia-mcu-watchdog.o

index 7b755bb4e4e7..59079d63fe27 100644
@@ -218,7 +218,22 @@ i2c@0 {
 			#size-cells = <0>;
 			reg = <0>;
 
-			/* STM32F0 command interface at address 0x2a */
+			mcu: system-controller@2a {
+				compatible = "cznic,turris-omnia-mcu";
+				reg = <0x2a>;
+
+				pinctrl-names = "default";
+				pinctrl-0 = <&mcu_pins>;
+
+				interrupt-parent = <&gpio1>;
+				interrupts = <11 IRQ_TYPE_NONE>;
+
+				gpio-controller;
+				#gpio-cells = <3>;
+
+				interrupt-controller;
+				#interrupt-cells = <2>;
+			};
 
 			led-controller@2b {
 				compatible = "cznic,turris-omnia-leds";

@@ -501,6 +516,11 @@ fixed-link {
 };
 
 &pinctrl {
+	mcu_pins: mcu-pins {
+		marvell,pins = "mpp43";
+		marvell,function = "gpio";
+	};
+
 	pcawan_pins: pcawan-pins {
 		marvell,pins = "mpp46";
 		marvell,function = "gpio";

index 59079d63fe27..43202890c959 100644
@@ -112,6 +112,19 @@ sfp: sfp {
 		status = "disabled";
 	};
 
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		front-button {
+			label = "Front Button";
+			linux,code = <KEY_VENDOR>;
+			linux,can-disable;
+			gpios = <&mcu 0 12 GPIO_ACTIVE_HIGH>;
+			/* debouncing is done by the microcontroller */
+			debounce-interval = <0>;
+		};
+	};
+
 	sound {
 		compatible = "simple-audio-card";
 		simple-audio-card,name = "SPDIF";