Skip to contentSkip to conversation

ARM: dts: stm32: Disable PHY clock output on DH STM32MP13xx DHCOR DHSBC board

PATCH In review Marek Vasut 2 participants 2 messages Jul 5, 2024 – Aug 30, 2024

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 ARM: dts: stm32: Disable PHY clock output on DH STM32MP13xx DHCOR DHSBC board

The RTL8211F PHY clock output is not used on DH STM32MP13xx DHCOR DHSBC board, disable it to improve EMI characteristics.

---
Cc: Alexandre Torgue <[email protected]>
Cc: Christophe Roullier <[email protected]>
Cc: Conor Dooley <[email protected]>
Cc: Krzysztof Kozlowski <[email protected]>
Cc: Maxime Coquelin <[email protected]>
Cc: Rob Herring <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]

---
 arch/arm/boot/dts/st/stm32mp135f-dhcor-dhsbc.dts | 2 ++
 1 file changed, 2 insertions(+)
arch/arm/boot/dts/st/stm32mp135f-dhcor-dhsbc.dts +2 -0
index 3cc9ad88d61bc..425deb5641c17 100644
@@ -96,6 +96,7 @@ ethphy1: ethernet-phy@1 {
 			interrupt-parent = <&gpiog>;
 			interrupts = <12 IRQ_TYPE_LEVEL_LOW>;
 			reg = <1>;
+			realtek,clkout-disable;
 			reset-assert-us = <15000>;
 			reset-deassert-us = <55000>;
 			reset-gpios = <&gpioa 11 GPIO_ACTIVE_LOW>;
@@ -125,6 +126,7 @@ ethphy2: ethernet-phy@1 {
 			interrupt-parent = <&gpiog>;
 			interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
 			reg = <1>;
+			realtek,clkout-disable;
 			reset-assert-us = <15000>;
 			reset-deassert-us = <55000>;
 			reset-gpios = <&gpiog 8 GPIO_ACTIVE_LOW>;
Signature · 1 line
2.43.0
maintainer
#1 lore raw

Hi Marek

Quoted 32 lines · Marek Vasut

The RTL8211F PHY clock output is not used on DH STM32MP13xx DHCOR DHSBC board, disable it to improve EMI characteristics.

---
Cc: Alexandre Torgue <[email protected]>
Cc: Christophe Roullier <[email protected]>
Cc: Conor Dooley <[email protected]>
Cc: Krzysztof Kozlowski <[email protected]>
Cc: Maxime Coquelin <[email protected]>
Cc: Rob Herring <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]

---
  arch/arm/boot/dts/st/stm32mp135f-dhcor-dhsbc.dts | 2 ++
  1 file changed, 2 insertions(+)
arch/arm/boot/dts/st/stm32mp135f-dhcor-dhsbc.dts +1 -0
index 3cc9ad88d61bc..425deb5641c17 100644
@@ -96,6 +96,7 @@ ethphy1: ethernet-phy@1 {
  			interrupt-parent = <&gpiog>;
  			interrupts = <12 IRQ_TYPE_LEVEL_LOW>;
  			reg = <1>;
+			realtek,clkout-disable;
  			reset-assert-us = <15000>;
  			reset-deassert-us = <55000>;
  			reset-gpios = <&gpioa 11 GPIO_ACTIVE_LOW>;

arch/arm/boot/dts/st/stm32mp135f-dhcor-dhsbc.dts ethphy2: ethernet-phy@1 { · line 132

Quoted 7 lines
arch/arm/boot/dts/st/stm32mp135f-dhcor-dhsbc.dts +1 -0
@@ -125,6 +126,7 @@ ethphy2: ethernet-phy@1 {
  			interrupt-parent = <&gpiog>;
  			interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
  			reg = <1>;
+			realtek,clkout-disable;
  			reset-assert-us = <15000>;
  			reset-deassert-us = <55000>;
  			reset-gpios = <&gpiog 8 GPIO_ACTIVE_LOW>;

Applied on stm32-next.

Regards
Alex