arm64: dts: amlogic: enable some device nodes for S4
Subsystems (2)
PATCH v2 1/1 arm64: dts: amlogic: enable some device nodes for S4
Enable more device nodes for AQ222 base S4, including SD, regulator and ethnernet node.
---
Add more device nodes for S4.
---
Changes in v2:
- Delete status of regulator-vddcpu node, use default status OK.
- Link to v1: https://lore.kernel.org/r/[email protected]
--- .../boot/dts/amlogic/meson-s4-s805x2-aq222.dts | 145 +++++++++++++++++++++ arch/arm64/boot/dts/amlogic/meson-s4.dtsi | 128 ++++++++++++++++++ 2 files changed, 273 insertions(+)
arch/arm64/boot/dts/amlogic/meson-s4-s805x2-aq222.dts +145 -0
@@ -34,6 +34,111 @@ secmon_reserved: secmon@5000000 { no-map; }; }; + + sdio_32k: sdio-32k { + compatible = "pwm-clock"; + #clock-cells = <0>; + clock-frequency = <32768>; + pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */ + }; + + sdio_pwrseq: sdio-pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>; + clocks = <&sdio_32k>; + clock-names = "ext_clock"; + }; + + main_12v: regulator-main-12v { + compatible = "regulator-fixed"; + regulator-name = "12V"; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + regulator-always-on; + }; + + vddao_3v3: regulator-vddao-3v3 { + compatible = "regulator-fixed"; + regulator-name = "VDDAO_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&main_12v>; + regulator-always-on; + }; + + vddio_ao1v8: regulator-vddio-ao1v8 { + compatible = "regulator-fixed"; + regulator-name = "VDDIO_AO1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vddao_3v3>; + regulator-always-on; + }; + + /* SY8120B1ABC DC/DC Regulator. */ + vddcpu: regulator-vddcpu { + compatible = "pwm-regulator"; + + regulator-name = "VDDCPU"; + regulator-min-microvolt = <689000>; + regulator-max-microvolt = <1049000>; + + vin-supply = <&main_12v>; + + pwms = <&pwm_ij 1 1500 0>; + pwm-dutycycle-range = <100 0>; + + regulator-boot-on; + regulator-always-on; + /* Voltage Duty-Cycle */ + voltage-table = <1049000 0>, + <1039000 3>, + <1029000 6>, + <1019000 9>, + <1009000 12>, + <999000 14>, + <989000 17>, + <979000 20>, + <969000 23>, + <959000 26>, + <949000 29>, + <939000 31>, + <929000 34>, + <919000 37>, + <909000 40>, + <899000 43>, + <889000 45>, + <879000 48>, + <869000 51>, + <859000 54>, + <849000 56>, + <839000 59>, + <829000 62>, + <819000 65>, + <809000 68>, + <799000 70>, + <789000 73>, + <779000 76>, + <769000 79>, + <759000 81>, + <749000 84>, + <739000 87>, + <729000 89>, + <719000 92>, + <709000 95>, + <699000 98>, + <689000 100>; + }; +}; + +&pwm_ef { + status = "okay"; + pinctrl-0 = <&pwm_e_pins1>; + pinctrl-names = "default"; +}; + +&pwm_ij { + status = "okay"; }; &uart_b {
@@ -46,6 +151,40 @@ &ir { pinctrl-names = "default"; }; +&sdio { + pinctrl-0 = <&sdio_pins>; + pinctrl-1 = <&sdio_clk_gate_pins>; + pinctrl-names = "default", "clk-gate"; + #address-cells = <1>; + #size-cells = <0>; + bus-width = <4>; + cap-sd-highspeed; + sd-uhs-sdr50; + sd-uhs-sdr104; + max-frequency = <200000000>; + non-removable; + disable-wp; + no-sd; + no-mmc; + vmmc-supply = <&vddao_3v3>; + vqmmc-supply = <&vddio_ao1v8>; +}; + +&sd { + status = "okay"; + pinctrl-0 = <&sdcard_pins>; + pinctrl-1 = <&sdcard_clk_gate_pins>; + pinctrl-names = "default", "clk-gate"; + bus-width = <4>; + cap-sd-highspeed; + max-frequency = <200000000>; + disable-wp; + + cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>; + vmmc-supply = <&vddao_3v3>; + vqmmc-supply = <&vddao_3v3>; +}; + &nand { status = "okay"; #address-cells = <1>;
@@ -90,3 +229,9 @@ &spicc0 { pinctrl-0 = <&spicc0_pins_x>; cs-gpios = <&gpio GPIOX_10 GPIO_ACTIVE_LOW>; }; + +ðmac { + status = "okay"; + phy-handle = <&internal_ephy>; + phy-mode = "rmii"; +};
arch/arm64/boot/dts/amlogic/meson-s4.dtsi +128 -0
145 lines not on this page · raw message
---
base-commit: 338c92a5d1956f1841f84b86923087676d1d0cea
change-id: 20240705-s4_node-8110e3286c0c
Best regards,
Signature · 1 line
Xianwei Zhao <[email protected]>
Hi,
Quoted 4 lines · Xianwei Zhao
Enable more device nodes for AQ222 base S4, including SD, regulator and ethnernet node.
Thanks, Applied to https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux.git (v6.11/arm64-dt)
[1/1] arm64: dts: amlogic: enable some device nodes for S4
https://git.kernel.org/amlogic/c/d3cc1daf38aaa0dd6546dd915ce5d536c250f3eb
These changes has been applied on the intermediate git tree [1].
The v6.11/arm64-dt branch will then be sent via a formal Pull Request to the Linux SoC maintainers for inclusion in their intermediate git branches in order to be sent to Linus during the next merge window, or sooner if it's a set of fixes.
In the cases of fixes, those will be merged in the current release candidate kernel and as soon they appear on the Linux master branch they will be backported to the previous Stable and Long-Stable kernels [2].
The intermediate git branches are merged daily in the linux-next tree [3], people are encouraged testing these pre-release kernels and report issues on the relevant mailing-lists.
If problems are discovered on those changes, please submit a signed-off-by revert patch followed by a corrective changeset.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux.git
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git
[3] https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git
Signature · 1 line
Neil