leds: leds-lp5569: Fix typo in driver name
PATCH v2 1/3 leds: leds-lp5569: Fix typo in driver name
Remove extra x from driver name as this was a typo from copy-paste error.
--- drivers/leds/leds-lp5569.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/leds/leds-lp5569.c +1 -1
@@ -529,7 +529,7 @@ MODULE_DEVICE_TABLE(of, of_lp5569_leds_match);static struct i2c_driver lp5569_driver = { .driver = { - .name ="lp5569x" , + .name ="lp5569" , .of_match_table = of_lp5569_leds_match, }, .probe = lp55xx_probe,
Signature · 1 line
2.45.2
PATCH v2 2/3 leds: leds-lp5569: Better handle enabling clock internal setting
Better handle enabling clock internal setting. In further testing it was notice that internal clock config MUST be set before clock output config or the LED CHIP might stop working.
This wasn't documented and was actually found on devices that have 2 chip chained where one chip provide clock for the other.
--- drivers/leds/leds-lp5569.c | 15 ++++++++++----- 1 file changed, 10 insertions(+), 5 deletions(-)
drivers/leds/leds-lp5569.c +10 -5
@@ -179,20 +179,25 @@ static int lp5569_post_init_device(struct lp55xx_chip *chip) val =LP5569_DEFAULT_CONFIG ; val |=FIELD_PREP (LP5569_CP_MODE_MASK , chip->pdata->charge_pump_mode); + ret =lp55xx_write (chip,LP5569_REG_MISC , val); +if (ret) +return ret;if (chip->pdata->clock_mode ==LP55XX_CLOCK_INT ) { +/* Internal clock MUST be configured before CLK output */ + ret =lp55xx_update_bits (chip,LP5569_REG_MISC , +LP5569_INTERNAL_CLK , +LP5569_INTERNAL_CLK ); +if (ret) +return ret; + ret =lp55xx_update_bits (chip,LP5569_REG_IO_CONTROL ,LP5569_CLK_OUTPUT ,LP5569_CLK_OUTPUT );if (ret)return ret; - - val |=LP5569_INTERNAL_CLK ; } - ret =lp55xx_write (chip,LP5569_REG_MISC , val); -if (ret) -return ret;return lp5569_init_program_engine (chip); }
Signature · 1 line
2.45.2
PATCH v2 3/3 leds: leds-lp5569: Enable chip after chip configuration
In reply to Christian MarangiDocumentation say that clock internal config needs to be set BEFORE chip is enabled. Align code to this and move the CHIP enable after the CHIP is configured.
While at it also make use of STATUS reg and check when STARTUP is completed instead of sleep for 1-2 ms.
---
Changes v2:
- Fix compilation warning (u8 instead of int)
drivers/leds/leds-lp5569.c | 19 +++++++++++-------- 1 file changed, 11 insertions(+), 8 deletions(-)
drivers/leds/leds-lp5569.c +11 -8
@@ -7,6 +7,7 @@#include <linux/delay.h> #include <linux/firmware.h> #include <linux/i2c.h> +#include <linux/iopoll.h> #include <linux/leds.h> #include <linux/module.h> #include <linux/mutex.h>
@@ -91,6 +92,8 @@#define LP5569_ENG2_MUX_ADDR 0xd0#define LP5569_ENG3_MUX_ADDR 0xe0 +#define LP5569_STARTUP_SLEEP 500 +#define LEDn_STATUS_FAULT (n, status) ((status) >> (n) & BIT(0))#define LP5569_DEFAULT_CONFIG \
@@ -168,14 +171,7 @@ static int lp5569_init_program_engine(struct lp55xx_chip *chip)static int lp5569_post_init_device (struct lp55xx_chip *chip) {int ret; -int val; - - ret =lp55xx_write (chip,LP5569_REG_ENABLE ,LP5569_ENABLE ); -if (ret) -return ret; - -/* Chip startup time is 500 us, 1 - 2 ms gives some margin */ -usleep_range (1000 ,2000 ); +u8 val; val =LP5569_DEFAULT_CONFIG ; val |=FIELD_PREP (LP5569_CP_MODE_MASK , chip->pdata->charge_pump_mode);
@@ -198,6 +194,13 @@ static int lp5569_post_init_device(struct lp55xx_chip *chip)return ret; } + ret =lp55xx_write (chip,LP5569_REG_ENABLE ,LP5569_ENABLE ); +if (ret) +return ret; + +read_poll_timeout (lp55xx_read, ret, !(val &LP5569_STARTUP_BUSY ), +LP5569_STARTUP_SLEEP ,LP5569_STARTUP_SLEEP *10 , false, + chip,LP5569_REG_STATUS , &val);return lp5569_init_program_engine (chip); }
Signature · 1 line
2.45.2