Skip to contentSkip to conversation

arm64: dts: layerscape: collect all fix warning patches

PATCH Applied Frank Li 2 participants 12 messages Jul 29, 2024 – Aug 13, 2024

Subsystems (2)
lore
Share & tools
lore

Frank Li

author maintainer
#0 lore raw

v2 cover arm64: dts: layerscape: collect all fix warning patches

Start from v2, since previous already sent as v1.

Collect 4 thread
[email protected]
[email protected]
20240703-ls_reset_syscon-v1-2-338f41b3902d
[email protected]

Change from v1 to v2
- fix typo layersacpe.

---
Frank Li (10):
arm64: dts: layerscape: rename aux-bus to bus
arm64: dts: layerscape: rename rcpm as wakeup-control from power-control
arm64: dts: layerscape: use common pcs-handle property
arm64: dts: fsl-ls1043a: change uqe to uqe-bus and remove #address-cells
arm64: dts: fsl-ls1028a: add fsl,ls1028-reset for syscon
arm64: dts: layerscape: add msi-cell = <1> for gic its
arm64: dts: layerscape: remove big-endian for mmc nodes
arm64: dts: fsl-ls1046a: remove big-endian at memory-controller
arm64: dts: layerscape: remove undocumented fsl,ls-pcie-ep
arm64: dts: fsl,ls2085a: remove fsl,ls2085a-pcie

 arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi     |  4 +---
 arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi     | 26 +++++++++++-----------
 arch/arm64/boot/dts/freescale/fsl-ls1043-post.dtsi |  3 +++
 arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi     | 13 +++--------
 arch/arm64/boot/dts/freescale/fsl-ls1046-post.dtsi |  4 ++++
 arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi     | 13 +++++------
 arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi     | 17 +++++++-------
 arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi     | 21 ++++++++---------
 arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi     | 17 +++++++-------
 .../boot/dts/freescale/qoriq-fman3-0-10g-0.dtsi    |  1 +
 .../boot/dts/freescale/qoriq-fman3-0-10g-1.dtsi    |  1 +
 .../boot/dts/freescale/qoriq-fman3-0-1g-0.dtsi     |  1 +
 .../boot/dts/freescale/qoriq-fman3-0-1g-1.dtsi     |  1 +
 .../boot/dts/freescale/qoriq-fman3-0-1g-2.dtsi     |  1 +
 .../boot/dts/freescale/qoriq-fman3-0-1g-3.dtsi     |  1 +
 .../boot/dts/freescale/qoriq-fman3-0-1g-4.dtsi     |  1 +
 16 files changed, 65 insertions(+), 60 deletions(-)

---
base-commit: 8400291e289ee6b2bf9779ff1c83a291501f017b
change-id: 20240729-ls_warning_all-9e2eaa9a033b

Best regards,
---
Frank Li <[email protected]>

author maintainer
#1 lore raw

PATCH v2 1/10 arm64: dts: layerscape: rename aux-bus to bus

The node name 'aux-bus' is special word. It invokes dp-aux-bus.yaml binding check. Simple change to 'bus' to fix below warning.

aux-bus: '#address-cells', '#size-cells', 'compatible', 'dma-ranges', 'ranges', 'sata@3200000', 'usb@2f00000', 'usb@3000000', 'usb@3100000' do not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/display/dp-aux-bus.yaml#

---
 arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi | 2 +-
 arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)
arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi +1 -1
index 17f4e31711209..b19a024525cbc 100644
@@ -804,7 +804,7 @@ QORIQ_CLK_PLL_DIV(1)>,
 					    QORIQ_CLK_PLL_DIV(1)>;
 		};
 
-		aux_bus: aux-bus {
+		aux_bus: bus {
 			#address-cells = <2>;
 			#size-cells = <2>;
 			compatible = "simple-bus";
arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi +1 -1
index 200e52622f998..6e244dc4832d1 100644
@@ -715,7 +715,7 @@ QORIQ_CLK_PLL_DIV(2)>,
 					    QORIQ_CLK_PLL_DIV(2)>;
 		};
 
-		aux_bus: aux-bus {
+		aux_bus: bus {
 			#address-cells = <2>;
 			#size-cells = <2>;
 			compatible = "simple-bus";
Signature · 1 line
2.34.1
author maintainer
#2 lore raw

PATCH v2 2/10 arm64: dts: layerscape: rename rcpm as wakeup-control from power-control

In reply to Frank Li

Invoke power-domain.yaml if node name as 'power-control'.

Rcpm actually are not power domain controller. It just control wakeup capability. So rename it as wakeup-control. Fix below CHECK_DTBS warning.

power-controller@1ee2140: '#power-domain-cells' is a required property
from schema $id: http://devicetree.org/schemas/power/power-domain.yaml#

---
 arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi | 2 +-
 arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi | 2 +-
 arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi | 2 +-
 arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi | 2 +-
 arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi | 2 +-
 arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi | 2 +-
 arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi | 2 +-
 7 files changed, 7 insertions(+), 7 deletions(-)
arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi +1 -1
index e61ea7e0737e4..dfd245b326a0d 100644
@@ -556,7 +556,7 @@ pcie1: pcie@3400000 {
 			status = "disabled";
 		};
 
-		rcpm: power-controller@1ee2140 {
+		rcpm: wakeup-controller@1ee2140 {
 			compatible = "fsl,ls1012a-rcpm", "fsl,qoriq-rcpm-2.1+";
 			reg = <0x0 0x1ee2140 0x0 0x4>;
 			#fsl,rcpm-wakeup-cells = <1>;
arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi +1 -1
index 6b6e3ee950e53..24e86abe88ea1 100644
@@ -1319,7 +1319,7 @@ pwm7: pwm@2870000 {
 			status = "disabled";
 		};
 
-		rcpm: power-controller@1e34040 {
+		rcpm: wakeup-controller@1e34040 {
 			compatible = "fsl,ls1028a-rcpm", "fsl,qoriq-rcpm-2.1+";
 			reg = <0x0 0x1e34040 0x0 0x1c>;
 			#fsl,rcpm-wakeup-cells = <7>;
arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi +1 -1
index b19a024525cbc..c176d36f68437 100644
@@ -983,7 +983,7 @@ qdma: dma-controller@8380000 {
 			big-endian;
 		};
 
-		rcpm: power-controller@1ee2140 {
+		rcpm: wakeup-controller@1ee2140 {
 			compatible = "fsl,ls1043a-rcpm", "fsl,qoriq-rcpm-2.1+";
 			reg = <0x0 0x1ee2140 0x0 0x4>;
 			#fsl,rcpm-wakeup-cells = <1>;
arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi +1 -1
index 6e244dc4832d1..baf9cb90ba8e7 100644
@@ -935,7 +935,7 @@ qdma: dma-controller@8380000 {
 			big-endian;
 		};
 
-		rcpm: power-controller@1ee2140 {
+		rcpm: wakeup-controller@1ee2140 {
 			compatible = "fsl,ls1046a-rcpm", "fsl,qoriq-rcpm-2.1+";
 			reg = <0x0 0x1ee2140 0x0 0x4>;
 			#fsl,rcpm-wakeup-cells = <1>;
arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi +1 -1
index 8ce4b6aae79d4..c980f4c5dcfdc 100644
@@ -1033,7 +1033,7 @@ dpmac10: ethernet@a {
 			};
 		};
 
-		rcpm: power-controller@1e34040 {
+		rcpm: wakeup-controller@1e34040 {
 			compatible = "fsl,ls1088a-rcpm", "fsl,qoriq-rcpm-2.1+";
 			reg = <0x0 0x1e34040 0x0 0x18>;
 			#fsl,rcpm-wakeup-cells = <6>;
arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi +1 -1
index bde89de2576e1..8691117ffcf76 100644
@@ -1218,7 +1218,7 @@ ccn@4000000 {
 			interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
-		rcpm: power-controller@1e34040 {
+		rcpm: wakeup-controller@1e34040 {
 			compatible = "fsl,ls208xa-rcpm", "fsl,qoriq-rcpm-2.1+";
 			reg = <0x0 0x1e34040 0x0 0x18>;
 			#fsl,rcpm-wakeup-cells = <6>;
arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi +1 -1
index 26c7ca31e22e7..73ee45acfde13 100644
@@ -1078,7 +1078,7 @@ watchdog@23a0000 {
 			timeout-sec = <30>;
 		};
 
-		rcpm: power-controller@1e34040 {
+		rcpm: wakeup-controller@1e34040 {
 			compatible = "fsl,lx2160a-rcpm", "fsl,qoriq-rcpm-2.1+";
 			reg = <0x0 0x1e34040 0x0 0x1c>;
 			#fsl,rcpm-wakeup-cells = <7>;
Signature · 1 line
2.34.1
author maintainer
#3 lore raw

PATCH v2 3/10 arm64: dts: layerscape: use common pcs-handle property

In reply to Frank Li

pcsphy-handle already deprecated according to binding fsl,fman-dtsec.yaml. Add new common pcs-handle at dts and fix below CHECK_DTBS warning.

arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dtb: fman@1a00000: ethernet@e0000: 'pcs-handle' is a dependency of 'pcs-handle-names'
from schema $id: http://devicetree.org/schemas/net/fsl,fman.yaml#

---
 arch/arm64/boot/dts/freescale/fsl-ls1043-post.dtsi     | 3 +++
 arch/arm64/boot/dts/freescale/fsl-ls1046-post.dtsi     | 4 ++++
 arch/arm64/boot/dts/freescale/qoriq-fman3-0-10g-0.dtsi | 1 +
 arch/arm64/boot/dts/freescale/qoriq-fman3-0-10g-1.dtsi | 1 +
 arch/arm64/boot/dts/freescale/qoriq-fman3-0-1g-0.dtsi  | 1 +
 arch/arm64/boot/dts/freescale/qoriq-fman3-0-1g-1.dtsi  | 1 +
 arch/arm64/boot/dts/freescale/qoriq-fman3-0-1g-2.dtsi  | 1 +
 arch/arm64/boot/dts/freescale/qoriq-fman3-0-1g-3.dtsi  | 1 +
 arch/arm64/boot/dts/freescale/qoriq-fman3-0-1g-4.dtsi  | 1 +
 9 files changed, 14 insertions(+)
arch/arm64/boot/dts/freescale/fsl-ls1043-post.dtsi +3 -0
index 5c4d7eef8b615..ca7cd7a33c017 100644
@@ -29,6 +29,7 @@ enet0: ethernet@e0000 {
 
 	enet1: ethernet@e2000 {
 		pcsphy-handle = <&pcsphy1>, <&qsgmiib_pcs1>;
+		pcs-handle = <&pcsphy1>, <&qsgmiib_pcs1>;
 		pcs-handle-names = "sgmii", "qsgmii";
 	};
 
@@ -40,11 +41,13 @@ enet3: ethernet@e6000 {
 
 	enet4: ethernet@e8000 {
 		pcsphy-handle = <&pcsphy4>, <&qsgmiib_pcs2>;
+		pcs-handle = <&pcsphy4>, <&qsgmiib_pcs2>;
 		pcs-handle-names = "sgmii", "qsgmii";
 	};
 
 	enet5: ethernet@ea000 {
 		pcsphy-handle = <&pcsphy5>, <&qsgmiib_pcs3>;
+		pcs-handle = <&pcsphy5>, <&qsgmiib_pcs3>;
 		pcs-handle-names = "sgmii", "qsgmii";
 	};
 
arch/arm64/boot/dts/freescale/fsl-ls1046-post.dtsi +4 -0
index 4e33450939436..15ff7c569d288 100644
@@ -24,6 +24,7 @@ &fman0 {
 	/* these aliases provide the FMan ports mapping */
 	enet0: ethernet@e0000 {
 		pcsphy-handle = <&qsgmiib_pcs3>;
+		pcs-handle = <&qsgmiib_pcs3>;
 		pcs-handle-names = "qsgmii";
 	};
 
@@ -38,11 +39,13 @@ enet3: ethernet@e6000 {
 
 	enet4: ethernet@e8000 {
 		pcsphy-handle = <&pcsphy4>, <&qsgmiib_pcs1>;
+		pcs-handle = <&pcsphy4>, <&qsgmiib_pcs1>;
 		pcs-handle-names = "sgmii", "qsgmii";
 	};
 
 	enet5: ethernet@ea000 {
 		pcsphy-handle = <&pcsphy5>, <&pcsphy5>;
+		pcs-handle = <&pcsphy5>, <&pcsphy5>;
 		pcs-handle-names = "sgmii", "qsgmii";
 	};
 
@@ -51,6 +54,7 @@ enet6: ethernet@f0000 {
 
 	enet7: ethernet@f2000 {
 		pcsphy-handle = <&pcsphy7>, <&qsgmiib_pcs2>, <&pcsphy7>;
+		pcs-handle = <&pcsphy7>, <&qsgmiib_pcs2>, <&pcsphy7>;
 		pcs-handle-names = "sgmii", "qsgmii", "xfi";
 	};
 
arch/arm64/boot/dts/freescale/qoriq-fman3-0-10g-0.dtsi +1 -0
index 65f7b5a50eb51..1b2b20c6126dc 100644
@@ -27,6 +27,7 @@ ethernet@f0000 {
 		reg = <0xf0000 0x1000>;
 		fsl,fman-ports = <&fman0_rx_0x10 &fman0_tx_0x30>;
 		pcsphy-handle = <&pcsphy6>;
+		pcs-handle = <&pcsphy6>;
 	};
 
 	mdio@f1000 {
arch/arm64/boot/dts/freescale/qoriq-fman3-0-10g-1.dtsi +1 -0
index 3f70482c98c30..55d78f6f7c6ca 100644
@@ -27,6 +27,7 @@ ethernet@f2000 {
 		reg = <0xf2000 0x1000>;
 		fsl,fman-ports = <&fman0_rx_0x11 &fman0_tx_0x31>;
 		pcsphy-handle = <&pcsphy7>;
+		pcs-handle = <&pcsphy7>;
 	};
 
 	mdio@f3000 {
arch/arm64/boot/dts/freescale/qoriq-fman3-0-1g-0.dtsi +1 -0
index 78841c1f32527..18916a860c2ed 100644
@@ -26,6 +26,7 @@ ethernet@e0000 {
 		fsl,fman-ports = <&fman0_rx_0x08 &fman0_tx_0x28>;
 		ptp-timer = <&ptp_timer0>;
 		pcsphy-handle = <&pcsphy0>;
+		pcs-handle = <&pcsphy0>;
 	};
 
 	mdio@e1000 {
arch/arm64/boot/dts/freescale/qoriq-fman3-0-1g-1.dtsi +1 -0
index 1f43fa6662221..e90af445a293d 100644
@@ -26,6 +26,7 @@ ethernet@e2000 {
 		fsl,fman-ports = <&fman0_rx_0x09 &fman0_tx_0x29>;
 		ptp-timer = <&ptp_timer0>;
 		pcsphy-handle = <&pcsphy1>;
+		pcs-handle = <&pcsphy1>;
 	};
 
 	mdio@e3000 {
arch/arm64/boot/dts/freescale/qoriq-fman3-0-1g-2.dtsi +1 -0
index de0aa017701dd..fec93905bc818 100644
@@ -26,6 +26,7 @@ ethernet@e4000 {
 		fsl,fman-ports = <&fman0_rx_0x0a &fman0_tx_0x2a>;
 		ptp-timer = <&ptp_timer0>;
 		pcsphy-handle = <&pcsphy2>;
+		pcs-handle = <&pcsphy2>;
 	};
 
 	mdio@e5000 {
arch/arm64/boot/dts/freescale/qoriq-fman3-0-1g-3.dtsi +1 -0
index 6904aa5d8e547..2aa953faa62b1 100644
@@ -26,6 +26,7 @@ ethernet@e6000 {
 		fsl,fman-ports = <&fman0_rx_0x0b &fman0_tx_0x2b>;
 		ptp-timer = <&ptp_timer0>;
 		pcsphy-handle = <&pcsphy3>;
+		pcs-handle = <&pcsphy3>;
 	};
 
 	mdio@e7000 {
arch/arm64/boot/dts/freescale/qoriq-fman3-0-1g-4.dtsi +1 -0
index a3d29d470297e..948e39411415e 100644
@@ -26,6 +26,7 @@ ethernet@e8000 {
 		fsl,fman-ports = <&fman0_rx_0x0c &fman0_tx_0x2c>;
 		ptp-timer = <&ptp_timer0>;
 		pcsphy-handle = <&pcsphy4>;
+		pcs-handle = <&pcsphy4>;
 	};
 
 	mdio@e9000 {
Signature · 1 line
2.34.1
author maintainer
#4 lore raw

PATCH v2 4/10 arm64: dts: fsl-ls1043a: change uqe to uqe-bus and remove #address-cells

In reply to Frank Li

Change node name 'uqe' to 'uqe-bus'.
Remove #address-cells and #size-cells for nodes, which have not child node.

Fix below CHECK_DTBS warning:
arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dtb: uqe@2400000: si@700: '#address-cells', '#size-cells' do not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/soc/fsl/cpm_qe/fsl,qe.yaml#
arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dtb: uqe@2400000: siram@1000: '#address-cells', '#size-cells' do not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/soc/fsl/cpm_qe/fsl,qe.yaml#
arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dtb: uqe@2400000: $nodename:0: 'uqe@2400000' does not match '^([a-z][a-z0-9\\-]+-bus|bus|localbus|soc|axi|ahb|apb)(@.+)?$'
from schema $id: http://devicetree.org/schemas/soc/fsl/cpm_qe/fsl,qe.yaml#
arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dtb: uqe@2400000: Unevaluated properties are not allowed ('#address-cells', '#size-cells', 'qeic@80', 'ucc@2000', 'ucc@2200' were unexpected)
from schema $id: http://devicetree.org/schemas/soc/fsl/cpm_qe/fsl,qe.yaml#
arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dtb: qeic@80: '#address-cells' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/soc/fsl/cpm_qe/fsl,qe-ic.yaml#
arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dtb: si@700: '#address-cells', '#size-cells' do not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/soc/fsl/cpm_qe/fsl,qe-si.yaml#
arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dtb: siram@1000: '#address-cells', '#size-cells' do not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/soc/fsl/cpm_qe/fsl,qe-siram.yaml#

---
 arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi | 7 +------
 1 file changed, 1 insertion(+), 6 deletions(-)
arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi +1 -6
index c176d36f68437..6d89cb5ddfc9c 100644
@@ -653,7 +653,7 @@ gpio4: gpio@2330000 {
 			#interrupt-cells = <2>;
 		};
 
-		uqe: uqe@2400000 {
+		uqe: uqe-bus@2400000 {
 			#address-cells = <1>;
 			#size-cells = <1>;
 			compatible = "fsl,qe", "simple-bus";
@@ -667,7 +667,6 @@ uqe: uqe@2400000 {
 			qeic: qeic@80 {
 				compatible = "fsl,qe-ic";
 				reg = <0x80 0x80>;
-				#address-cells = <0>;
 				interrupt-controller;
 				#interrupt-cells = <1>;
 				interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>,
@@ -675,16 +674,12 @@ qeic: qeic@80 {
 			};
 
 			si1: si@700 {
-				#address-cells = <1>;
-				#size-cells = <0>;
 				compatible = "fsl,ls1043-qe-si",
 						"fsl,t1040-qe-si";
 				reg = <0x700 0x80>;
 			};
 
 			siram1: siram@1000 {
-				#address-cells = <1>;
-				#size-cells = <1>;
 				compatible = "fsl,ls1043-qe-siram",
 						"fsl,t1040-qe-siram";
 				reg = <0x1000 0x800>;
Signature · 1 line
2.34.1
author maintainer
#5 lore raw

PATCH v2 5/10 arm64: dts: fsl-ls1028a: add fsl,ls1028-reset for syscon

In reply to Frank Li

Add platform specific compatiable string 'fsl,ls1028-reset' for syscon and move reboot node under reset syscon node to fix below warning.

syscon@1e60000: compatible: 'anyOf' conditional failed, one must be fixed:
['syscon'] is too short
'syscon' is not one of ['al,alpine-sysfabric-service', ...

---
 arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi | 17 ++++++++---------
 1 file changed, 8 insertions(+), 9 deletions(-)
arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi +8 -9
index 24e86abe88ea1..701f0b2a3e579 100644
@@ -112,13 +112,6 @@ optee: optee  {
 		};
 	};
 
-	reboot {
-		compatible = "syscon-reboot";
-		regmap = <&rst>;
-		offset = <0>;
-		mask = <0x02>;
-	};
-
 	timer {
 		compatible = "arm,armv8-timer";
 		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) |
@@ -235,10 +228,16 @@ fspi_clk: clock-controller@900 {
 			};
 		};
 
-		rst: syscon@1e60000 {
-			compatible = "syscon";
+		syscon@1e60000 {
+			compatible = "fsl,ls1028a-reset", "syscon", "simple-mfd";
 			reg = <0x0 0x1e60000 0x0 0x10000>;
 			little-endian;
+
+			reboot {
+				compatible = "syscon-reboot";
+				offset = <0>;
+				mask = <0x02>;
+			};
 		};
 
 		sfp: efuse@1e80000 {
Signature · 1 line
2.34.1
author maintainer
#6 lore raw

PATCH v2 6/10 arm64: dts: layerscape: add msi-cell = <1> for gic its

In reply to Frank Li

Add msi-cell = <1> for GIC ITS. msi-parent have to be kept because it is checked by U-Boot due to historical reasons to fix up msi-map.

Fix below CHECK_DTBS warning:
arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-kbox-a-230-ls.dtb: interrupt-controller@6000000: msi-controller@6020000: '#msi-cells' is a required property
from schema $id: http://devicetree.org/schemas/interrupt-controller/arm,gic-v3.yaml

---
 arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi |  7 ++++---
 arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi |  9 +++++----
 arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi | 11 ++++++-----
 arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi | 15 ++++++++-------
 4 files changed, 23 insertions(+), 19 deletions(-)
arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi +4 -3
index 701f0b2a3e579..5e77c438f8840 100644
@@ -143,6 +143,7 @@ gic: interrupt-controller@6000000 {
 		its: msi-controller@6020000 {
 			compatible = "arm,gic-v3-its";
 			msi-controller;
+			#msi-cells = <1>;
 			reg = <0x0 0x06020000 0 0x20000>;/* GIC Translater */
 		};
 	};
@@ -661,7 +662,7 @@ pcie1: pcie@3400000 {
 			bus-range = <0x0 0xff>;
 			ranges = <0x81000000 0x0 0x00000000 0x80 0x00010000 0x0 0x00010000   /* downstream I/O */
 				  0x82000000 0x0 0x40000000 0x80 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
-			msi-parent = <&its>;
+			msi-parent = <&its 0>;
 			#interrupt-cells = <1>;
 			interrupt-map-mask = <0 0 0 7>;
 			interrupt-map = <0000 0 0 1 &gic 0 0 GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
@@ -700,7 +701,7 @@ pcie2: pcie@3500000 {
 			bus-range = <0x0 0xff>;
 			ranges = <0x81000000 0x0 0x00000000 0x88 0x00010000 0x0 0x00010000   /* downstream I/O */
 				  0x82000000 0x0 0x40000000 0x88 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
-			msi-parent = <&its>;
+			msi-parent = <&its 0>;
 			#interrupt-cells = <1>;
 			interrupt-map-mask = <0 0 0 7>;
 			interrupt-map = <0000 0 0 1 &gic 0 0 GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
@@ -1079,7 +1080,7 @@ pcie@1f0000000 { /* Integrated Endpoint Root Complex */
 			reg = <0x01 0xf0000000 0x0 0x100000>;
 			#address-cells = <3>;
 			#size-cells = <2>;
-			msi-parent = <&its>;
+			msi-parent = <&its 0>;
 			device_type = "pci";
 			bus-range = <0x0 0x0>;
 			dma-coherent;
arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi +5 -4
index c980f4c5dcfdc..3533779f737ab 100644
@@ -126,6 +126,7 @@ gic: interrupt-controller@6000000 {
 		its: msi-controller@6020000 {
 			compatible = "arm,gic-v3-its";
 			msi-controller;
+			#msi-cells = <1>;
 			reg = <0x0 0x6020000 0 0x20000>;
 		};
 	};
@@ -575,7 +576,7 @@ pcie1: pcie@3400000 {
 			bus-range = <0x0 0xff>;
 			ranges = <0x81000000 0x0 0x00000000 0x20 0x00010000 0x0 0x00010000   /* downstream I/O */
 				  0x82000000 0x0 0x40000000 0x20 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
-			msi-parent = <&its>;
+			msi-parent = <&its 0>;
 			#interrupt-cells = <1>;
 			interrupt-map-mask = <0 0 0 7>;
 			interrupt-map = <0000 0 0 1 &gic 0 0 0 109 IRQ_TYPE_LEVEL_HIGH>,
@@ -614,7 +615,7 @@ pcie2: pcie@3500000 {
 			bus-range = <0x0 0xff>;
 			ranges = <0x81000000 0x0 0x00000000 0x28 0x00010000 0x0 0x00010000   /* downstream I/O */
 				  0x82000000 0x0 0x40000000 0x28 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
-			msi-parent = <&its>;
+			msi-parent = <&its 0>;
 			#interrupt-cells = <1>;
 			interrupt-map-mask = <0 0 0 7>;
 			interrupt-map = <0000 0 0 1 &gic 0 0 0 114 IRQ_TYPE_LEVEL_HIGH>,
@@ -652,7 +653,7 @@ pcie3: pcie@3600000 {
 			bus-range = <0x0 0xff>;
 			ranges = <0x81000000 0x0 0x00000000 0x30 0x00010000 0x0 0x00010000   /* downstream I/O */
 				  0x82000000 0x0 0x40000000 0x30 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
-			msi-parent = <&its>;
+			msi-parent = <&its 0>;
 			#interrupt-cells = <1>;
 			interrupt-map-mask = <0 0 0 7>;
 			interrupt-map = <0000 0 0 1 &gic 0 0 0 119 IRQ_TYPE_LEVEL_HIGH>,
@@ -964,7 +965,7 @@ fsl_mc: fsl-mc@80c000000 {
 			compatible = "fsl,qoriq-mc";
 			reg = <0x00000008 0x0c000000 0 0x40>,	 /* MC portal base */
 			      <0x00000000 0x08340000 0 0x40000>; /* MC control reg */
-			msi-parent = <&its>;
+			msi-parent = <&its 0>;
 			iommu-map = <0 &smmu 0 0>;	/* This is fixed-up by u-boot */
 			dma-coherent;
 			#address-cells = <3>;
arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi +6 -5
index 8691117ffcf76..3213a8fe0b3b4 100644
@@ -63,6 +63,7 @@ gic: interrupt-controller@6000000 {
 		its: msi-controller@6020000 {
 			compatible = "arm,gic-v3-its";
 			msi-controller;
+			#msi-cells = <1>;
 			reg = <0x0 0x6020000 0 0x20000>;
 		};
 	};
@@ -758,7 +759,7 @@ fsl_mc: fsl-mc@80c000000 {
 			compatible = "fsl,qoriq-mc";
 			reg = <0x00000008 0x0c000000 0 0x40>,	 /* MC portal base */
 			      <0x00000000 0x08340000 0 0x40000>; /* MC control reg */
-			msi-parent = <&its>;
+			msi-parent = <&its 0>;
 			iommu-map = <0 &smmu 0 0>;	/* This is fixed-up by u-boot */
 			dma-coherent;
 			#address-cells = <3>;
@@ -1085,7 +1086,7 @@ pcie1: pcie@3400000 {
 			dma-coherent;
 			num-viewport = <6>;
 			bus-range = <0x0 0xff>;
-			msi-parent = <&its>;
+			msi-parent = <&its 0>;
 			#interrupt-cells = <1>;
 			interrupt-map-mask = <0 0 0 7>;
 			interrupt-map = <0000 0 0 1 &gic 0 0 0 109 4>,
@@ -1107,7 +1108,7 @@ pcie2: pcie@3500000 {
 			dma-coherent;
 			num-viewport = <6>;
 			bus-range = <0x0 0xff>;
-			msi-parent = <&its>;
+			msi-parent = <&its 0>;
 			#interrupt-cells = <1>;
 			interrupt-map-mask = <0 0 0 7>;
 			interrupt-map = <0000 0 0 1 &gic 0 0 0 114 4>,
@@ -1129,7 +1130,7 @@ pcie3: pcie@3600000 {
 			dma-coherent;
 			num-viewport = <256>;
 			bus-range = <0x0 0xff>;
-			msi-parent = <&its>;
+			msi-parent = <&its 0>;
 			#interrupt-cells = <1>;
 			interrupt-map-mask = <0 0 0 7>;
 			interrupt-map = <0000 0 0 1 &gic 0 0 0 119 4>,
@@ -1151,7 +1152,7 @@ pcie4: pcie@3700000 {
 			dma-coherent;
 			num-viewport = <6>;
 			bus-range = <0x0 0xff>;
-			msi-parent = <&its>;
+			msi-parent = <&its 0>;
 			#interrupt-cells = <1>;
 			interrupt-map-mask = <0 0 0 7>;
 			interrupt-map = <0000 0 0 1 &gic 0 0 0 124 4>,
arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi +8 -7
index 73ee45acfde13..8810f78c327c7 100644
@@ -398,6 +398,7 @@ gic: interrupt-controller@6000000 {
 		its: msi-controller@6020000 {
 			compatible = "arm,gic-v3-its";
 			msi-controller;
+			#msi-cells = <1>;
 			reg = <0x0 0x6020000 0 0x20000>;
 		};
 	};
@@ -1181,7 +1182,7 @@ pcie1: pcie@3400000 {
 			ppio-wins = <8>;
 			bus-range = <0x0 0xff>;
 			ranges = <0x82000000 0x0 0x40000000 0x80 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
-			msi-parent = <&its>;
+			msi-parent = <&its 0>;
 			#interrupt-cells = <1>;
 			interrupt-map-mask = <0 0 0 7>;
 			interrupt-map = <0000 0 0 1 &gic 0 0 GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
@@ -1209,7 +1210,7 @@ pcie2: pcie@3500000 {
 			ppio-wins = <8>;
 			bus-range = <0x0 0xff>;
 			ranges = <0x82000000 0x0 0x40000000 0x88 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
-			msi-parent = <&its>;
+			msi-parent = <&its 0>;
 			#interrupt-cells = <1>;
 			interrupt-map-mask = <0 0 0 7>;
 			interrupt-map = <0000 0 0 1 &gic 0 0 GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
@@ -1237,7 +1238,7 @@ pcie3: pcie@3600000 {
 			ppio-wins = <24>;
 			bus-range = <0x0 0xff>;
 			ranges = <0x82000000 0x0 0x40000000 0x90 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
-			msi-parent = <&its>;
+			msi-parent = <&its 0>;
 			#interrupt-cells = <1>;
 			interrupt-map-mask = <0 0 0 7>;
 			interrupt-map = <0000 0 0 1 &gic 0 0 GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>,
@@ -1265,7 +1266,7 @@ pcie4: pcie@3700000 {
 			ppio-wins = <8>;
 			bus-range = <0x0 0xff>;
 			ranges = <0x82000000 0x0 0x40000000 0x98 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
-			msi-parent = <&its>;
+			msi-parent = <&its 0>;
 			#interrupt-cells = <1>;
 			interrupt-map-mask = <0 0 0 7>;
 			interrupt-map = <0000 0 0 1 &gic 0 0 GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
@@ -1293,7 +1294,7 @@ pcie5: pcie@3800000 {
 			ppio-wins = <24>;
 			bus-range = <0x0 0xff>;
 			ranges = <0x82000000 0x0 0x40000000 0xa0 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
-			msi-parent = <&its>;
+			msi-parent = <&its 0>;
 			#interrupt-cells = <1>;
 			interrupt-map-mask = <0 0 0 7>;
 			interrupt-map = <0000 0 0 1 &gic 0 0 GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>,
@@ -1321,7 +1322,7 @@ pcie6: pcie@3900000 {
 			ppio-wins = <8>;
 			bus-range = <0x0 0xff>;
 			ranges = <0x82000000 0x0 0x40000000 0xa8 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
-			msi-parent = <&its>;
+			msi-parent = <&its 0>;
 			#interrupt-cells = <1>;
 			interrupt-map-mask = <0 0 0 7>;
 			interrupt-map = <0000 0 0 1 &gic 0 0 GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
@@ -1777,7 +1778,7 @@ fsl_mc: fsl-mc@80c000000 {
 			compatible = "fsl,qoriq-mc";
 			reg = <0x00000008 0x0c000000 0 0x40>,
 			      <0x00000000 0x08340000 0 0x40000>;
-			msi-parent = <&its>;
+			msi-parent = <&its 0>;
 			/* iommu-map property is fixed up by u-boot */
 			iommu-map = <0 &smmu 0 0>;
 			dma-coherent;
Signature · 1 line
2.34.1
author maintainer
#7 lore raw

PATCH v2 7/10 arm64: dts: layerscape: remove big-endian for mmc nodes

In reply to Frank Li

According to binding doc fsl,esdhc.yaml, the default endian mode is big-endian. So remove big-endian property to fix below CHECK_DTBS warnings:

arm64/boot/dts/freescale/fsl-ls1012a-qds.dtb: mmc@1560000: Unevaluated properties are not allowed ('big-endian' was unexpected)
from schema $id: http://devicetree.org/schemas/mmc/fsl,esdhc.yaml

---
 arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi | 2 --
 arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi | 1 -
 arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi | 2 --
 3 files changed, 5 deletions(-)
arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi +0 -2
index dfd245b326a0d..a3c57da63a01b 100644
@@ -164,7 +164,6 @@ esdhc0: mmc@1560000 {
 					    QORIQ_CLK_PLL_DIV(1)>;
 			voltage-ranges = <1800 1800 3300 3300>;
 			sdhci,auto-cmd12;
-			big-endian;
 			bus-width = <4>;
 			status = "disabled";
 		};
@@ -183,7 +182,6 @@ esdhc1: mmc@1580000 {
 					    QORIQ_CLK_PLL_DIV(1)>;
 			voltage-ranges = <1800 1800 3300 3300>;
 			sdhci,auto-cmd12;
-			big-endian;
 			broken-cd;
 			bus-width = <4>;
 			status = "disabled";
arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi +0 -1
index 6d89cb5ddfc9c..58daf3f1d6373 100644
@@ -431,7 +431,6 @@ esdhc: mmc@1560000 {
 			clock-frequency = <0>;
 			voltage-ranges = <1800 1800 3300 3300>;
 			sdhci,auto-cmd12;
-			big-endian;
 			bus-width = <4>;
 		};
 
arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi +0 -2
index baf9cb90ba8e7..41a1f4f2f880e 100644
@@ -315,7 +315,6 @@ esdhc: mmc@1560000 {
 			clocks = <&clockgen QORIQ_CLK_HWACCEL 1>;
 			voltage-ranges = <1800 1800 3300 3300>;
 			sdhci,auto-cmd12;
-			big-endian;
 			bus-width = <4>;
 		};
 
@@ -694,7 +693,6 @@ wdog0: watchdog@2ad0000 {
 			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(2)>;
-			big-endian;
 		};
 
 		edma0: dma-controller@2c00000 {
Signature · 1 line
2.34.1
author maintainer
#8 lore raw

PATCH v2 8/10 arm64: dts: fsl-ls1046a: remove big-endian at memory-controller

In reply to Frank Li

According to binding doc fsl,ddr.yaml, big-endian is default setting. So remove it to fix below CHECK_DTBS warnings.

arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dtb: memory-controller@1080000: 'big-endian' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/memory-controllers/fsl/fsl,ddr.yaml

---
 arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi | 1 -
 arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi | 1 -
 2 files changed, 2 deletions(-)
arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi +0 -1
index 58daf3f1d6373..cf92badc66558 100644
@@ -438,7 +438,6 @@ ddr: memory-controller@1080000 {
 			compatible = "fsl,qoriq-memory-controller";
 			reg = <0x0 0x1080000 0x0 0x1000>;
 			interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>;
-			big-endian;
 		};
 
 		tmu: tmu@1f00000 {
arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi +0 -1
index 41a1f4f2f880e..e33c04a8ea3f9 100644
@@ -282,7 +282,6 @@ ddr: memory-controller@1080000 {
 			compatible = "fsl,qoriq-memory-controller";
 			reg = <0x0 0x1080000 0x0 0x1000>;
 			interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>;
-			big-endian;
 		};
 
 		ifc: memory-controller@1530000 {
Signature · 1 line
2.34.1
author maintainer
#9 lore raw

PATCH v2 9/10 arm64: dts: layerscape: remove undocumented fsl,ls-pcie-ep

In reply to Frank Li

Remove undocumented compatible string fsl,ls-pcie-ep to fix below
CHECK_DTBS warning.
arch/arm64/boot/dts/freescale/fsl-ls1046a-frwy.dtb: pcie_ep@3400000: compatible: ['fsl,ls1046a-pcie-ep', 'fsl,ls-pcie-ep'] is too long
from schema $id: http://devicetree.org/schemas/pci/fsl,layerscape-pcie-ep.yaml

---
 arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi | 6 +++---
 arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi | 6 +++---
 2 files changed, 6 insertions(+), 6 deletions(-)
arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi +3 -3
index e33c04a8ea3f9..244ed720b4246 100644
@@ -820,7 +820,7 @@ pcie1: pcie@3400000 {
 		};
 
 		pcie_ep1: pcie_ep@3400000 {
-			compatible = "fsl,ls1046a-pcie-ep","fsl,ls-pcie-ep";
+			compatible = "fsl,ls1046a-pcie-ep";
 			reg = <0x00 0x03400000 0x0 0x00100000>,
 			      <0x40 0x00000000 0x8 0x00000000>;
 			reg-names = "regs", "addr_space";
@@ -859,7 +859,7 @@ pcie2: pcie@3500000 {
 		};
 
 		pcie_ep2: pcie_ep@3500000 {
-			compatible = "fsl,ls1046a-pcie-ep","fsl,ls-pcie-ep";
+			compatible = "fsl,ls1046a-pcie-ep";
 			reg = <0x00 0x03500000 0x0 0x00100000>,
 			      <0x48 0x00000000 0x8 0x00000000>;
 			reg-names = "regs", "addr_space";
@@ -898,7 +898,7 @@ pcie3: pcie@3600000 {
 		};
 
 		pcie_ep3: pcie_ep@3600000 {
-			compatible = "fsl,ls1046a-pcie-ep", "fsl,ls-pcie-ep";
+			compatible = "fsl,ls1046a-pcie-ep";
 			reg = <0x00 0x03600000 0x0 0x00100000>,
 			      <0x50 0x00000000 0x8 0x00000000>;
 			reg-names = "regs", "addr_space";
arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi +3 -3
index 3533779f737ab..9963fcc625a24 100644
@@ -588,7 +588,7 @@ pcie1: pcie@3400000 {
 		};
 
 		pcie_ep1: pcie-ep@3400000 {
-			compatible = "fsl,ls1088a-pcie-ep", "fsl,ls-pcie-ep";
+			compatible = "fsl,ls1088a-pcie-ep";
 			reg = <0x00 0x03400000 0x0 0x00100000>,
 			      <0x20 0x00000000 0x8 0x00000000>;
 			reg-names = "regs", "addr_space";
@@ -627,7 +627,7 @@ pcie2: pcie@3500000 {
 		};
 
 		pcie_ep2: pcie-ep@3500000 {
-			compatible = "fsl,ls1088a-pcie-ep", "fsl,ls-pcie-ep";
+			compatible = "fsl,ls1088a-pcie-ep";
 			reg = <0x00 0x03500000 0x0 0x00100000>,
 			      <0x28 0x00000000 0x8 0x00000000>;
 			reg-names = "regs", "addr_space";
@@ -665,7 +665,7 @@ pcie3: pcie@3600000 {
 		};
 
 		pcie_ep3: pcie-ep@3600000 {
-			compatible = "fsl,ls1088a-pcie-ep", "fsl,ls-pcie-ep";
+			compatible = "fsl,ls1088a-pcie-ep";
 			reg = <0x00 0x03600000 0x0 0x00100000>,
 			      <0x30 0x00000000 0x8 0x00000000>;
 			reg-names = "regs", "addr_space";
Signature · 1 line
2.34.1
author maintainer
#10 lore raw

PATCH v2 10/10 arm64: dts: fsl,ls2085a: remove fsl,ls2085a-pcie

In reply to Frank Li

fsl,ls2080a-pcie actual is the same as fsl,ls2085a-pcie. Only keep one is enough, so remove "fsl,ls2085a-pcie" to fix below warnings.

arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dtb: pcie@3400000: compatible: ['fsl,ls2080a-pcie', 'fsl,ls2085a-pcie'] is too long
from schema $id: http://devicetree.org/schemas/pci/fsl,layerscape-pcie.yaml#

---
 arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)
arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi +4 -4
index 3213a8fe0b3b4..d9ce0fbda1e1b 100644
@@ -1076,7 +1076,7 @@ QORIQ_CLK_PLL_DIV(4)>,
 		};
 
 		pcie1: pcie@3400000 {
-			compatible = "fsl,ls2080a-pcie", "fsl,ls2085a-pcie";
+			compatible = "fsl,ls2080a-pcie";
 			reg-names = "regs", "config";
 			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "intr";
@@ -1098,7 +1098,7 @@ pcie1: pcie@3400000 {
 		};
 
 		pcie2: pcie@3500000 {
-			compatible = "fsl,ls2080a-pcie", "fsl,ls2085a-pcie";
+			compatible = "fsl,ls2080a-pcie";
 			reg-names = "regs", "config";
 			interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "intr";
@@ -1120,7 +1120,7 @@ pcie2: pcie@3500000 {
 		};
 
 		pcie3: pcie@3600000 {
-			compatible = "fsl,ls2080a-pcie", "fsl,ls2085a-pcie";
+			compatible = "fsl,ls2080a-pcie";
 			reg-names = "regs", "config";
 			interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "intr";
@@ -1142,7 +1142,7 @@ pcie3: pcie@3600000 {
 		};
 
 		pcie4: pcie@3700000 {
-			compatible = "fsl,ls2080a-pcie", "fsl,ls2085a-pcie";
+			compatible = "fsl,ls2080a-pcie";
 			reg-names = "regs", "config";
 			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "intr";
Signature · 1 line
2.34.1
Applied
#11 lore raw
In reply to Frank Li
Quoted 11 lines · Frank Li

Frank Li (10):
arm64: dts: layerscape: rename aux-bus to bus
arm64: dts: layerscape: rename rcpm as wakeup-control from power-control
arm64: dts: layerscape: use common pcs-handle property
arm64: dts: fsl-ls1043a: change uqe to uqe-bus and remove #address-cells
arm64: dts: fsl-ls1028a: add fsl,ls1028-reset for syscon
arm64: dts: layerscape: add msi-cell = <1> for gic its
arm64: dts: layerscape: remove big-endian for mmc nodes
arm64: dts: fsl-ls1046a: remove big-endian at memory-controller
arm64: dts: layerscape: remove undocumented fsl,ls-pcie-ep
arm64: dts: fsl,ls2085a: remove fsl,ls2085a-pcie

Applied all, thanks!