spi: sunxi: fix CDR2 calculation
Subsystems (2)
PATCH v2 1/2 spi: sunxi: fix CDR2 calculation
The CDR2 divider calculation always yield a frequency greater than the requested one. Use DIV_ROUND_UP() to keep the frequency equal or below the requested one. This way, we can also drop the "if div > 0" check because we know for a fact that div cannot be zero.
FWIW, this aligns the CDR2 calculation with the linux driver.
--- drivers/spi/spi-sunxi.c | 11 ++++------- 1 file changed, 4 insertions(+), 7 deletions(-)
drivers/spi/spi-sunxi.c +4 -7
@@ -233,7 +233,7 @@ err_ahb:static void sun4i_spi_set_speed_mode (struct udevice *dev) {struct sun4i_spi_priv *priv =dev_get_priv (dev); -unsigned int div; +unsigned int div, div_cdr2;u32 reg;/*
@@ -259,15 +259,12 @@ static void sun4i_spi_set_speed_mode(struct udevice *dev)*/ div =DIV_ROUND_UP (SUNXI_INPUT_CLOCK , priv->freq); + div_cdr2 =DIV_ROUND_UP (div,2 ); reg =readl (SPI_REG (priv,SPI_CCR )); -if ((div /2 ) <= (SUN4I_CLK_CTL_CDR2_MASK +1 )) { - div /=2 ; -if (div >0 ) - div--; - +if (div_cdr2 <= (SUN4I_CLK_CTL_CDR2_MASK +1 )) { reg &= ~(SUN4I_CLK_CTL_CDR2_MASK |SUN4I_CLK_CTL_DRS ); - reg |=SUN4I_CLK_CTL_CDR2 (div) |SUN4I_CLK_CTL_DRS ; + reg |=SUN4I_CLK_CTL_CDR2 (div_cdr2 -1 ) |SUN4I_CLK_CTL_DRS ; }else { div =fls (div -1 );/* The F1C100s encodes the divider as 2^(n+1) */
Signature · 1 line
2.39.2
PATCH v2 2/2 spi: sunxi: fix clock divider calculation for max frequency setting
If the maximum frequency is requested, we still fall into the CDR2 handling. But there the minimal divider is 2. For the sun6i and sun8i we can do better with the CDR1 setting where the minimal divider is 1:
SPI_CLK = MOD_CLK / 2 ^ cdr with cdr = 0
Thus, handle the div = 1 case specially.
While at it, correct the comment above the calculation.
--- drivers/spi/spi-sunxi.c | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-)
drivers/spi/spi-sunxi.c +6 -1
@@ -249,6 +249,8 @@ static void sun4i_spi_set_speed_mode(struct udevice *dev)* We have two choices there. Either we can use the clock * divide rate 1, which is calculated thanks to this formula: * SPI_CLK = MOD_CLK / (2 ^ (cdr + 1)) +* Or for sun6i/sun8i variants: +* SPI_CLK = MOD_CLK / (2 ^ cdr) * Or we can use CDR2, which is calculated with the formula: * SPI_CLK = MOD_CLK / (2 * (cdr + 1)) * Whether we use the former or the latter is set through the
@@ -256,13 +258,16 @@ static void sun4i_spi_set_speed_mode(struct udevice *dev)* * First try CDR2, and if we can't reach the expected * frequency, fall back to CDR1. +* There is one exception if the requested clock is the input +* clock. In that case we always use CDR1 because we'll get a +* 1:1 ration for sun6i/sun8i variants. */ div =DIV_ROUND_UP (SUNXI_INPUT_CLOCK , priv->freq); div_cdr2 =DIV_ROUND_UP (div,2 ); reg =readl (SPI_REG (priv,SPI_CCR )); -if (div_cdr2 <= (SUN4I_CLK_CTL_CDR2_MASK +1 )) { +if (div !=1 && (div_cdr2 <= (SUN4I_CLK_CTL_CDR2_MASK +1 ))) { reg &= ~(SUN4I_CLK_CTL_CDR2_MASK |SUN4I_CLK_CTL_DRS ); reg |=SUN4I_CLK_CTL_CDR2 (div_cdr2 -1 ) |SUN4I_CLK_CTL_DRS ; }else {
Signature · 1 line
2.39.2
Re: [PATCH v2 2/2] spi: sunxi: fix clock divider calculation for max frequency setting
Quoted 10 lines · On Thu, 18 Jul 2024 22:42:53 +0200 Michael Walle <[email protected]> wrote:
If the maximum frequency is requested, we still fall into the CDR2 handling. But there the minimal divider is 2. For the sun6i and sun8i we can do better with the CDR1 setting where the minimal divider is 1:
SPI_CLK=MOD_CLK/ 2 ^ cdr with cdr = 0Thus, handle the div = 1 case specially.
While at it, correct the comment above the calculation.
Signed-off-by Michael Walle <[email protected]>
Applied to sunxi/master.
Cheers,
Andre
Quoted 35 lines
--- drivers/spi/spi-sunxi.c | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-)drivers/spi/spi-sunxi.c +6
-1@@ -249,6 +249,8 @@ static void sun4i_spi_set_speed_mode(struct udevice *dev)* We have two choices there. Either we can use the clock * divide rate 1, which is calculated thanks to this formula: * SPI_CLK = MOD_CLK / (2 ^ (cdr + 1)) +* Or for sun6i/sun8i variants: +* SPI_CLK = MOD_CLK / (2 ^ cdr) * Or we can use CDR2, which is calculated with the formula: * SPI_CLK = MOD_CLK / (2 * (cdr + 1)) * Whether we use the former or the latter is set through the @@ -256,13 +258,16 @@ static void sun4i_spi_set_speed_mode(struct udevice *dev)* * First try CDR2, and if we can't reach the expected * frequency, fall back to CDR1. +* There is one exception if the requested clock is the input +* clock. In that case we always use CDR1 because we'll get a +* 1:1 ration for sun6i/sun8i variants. */ div =DIV_ROUND_UP (SUNXI_INPUT_CLOCK , priv->freq); div_cdr2 =DIV_ROUND_UP (div,2 ); reg =readl (SPI_REG (priv,SPI_CCR )); -if (div_cdr2 <= (SUN4I_CLK_CTL_CDR2_MASK +1 )) { +if (div !=1 && (div_cdr2 <= (SUN4I_CLK_CTL_CDR2_MASK +1 ))) { reg &= ~(SUN4I_CLK_CTL_CDR2_MASK |SUN4I_CLK_CTL_DRS ); reg |=SUN4I_CLK_CTL_CDR2 (div_cdr2 -1 ) |SUN4I_CLK_CTL_DRS ; }else {
On Thu, 18 Jul 2024 22:42:52 +0200
Michael Walle <[email protected]> wrote:
Hi,
Quoted 6 lines
The CDR2 divider calculation always yield a frequency greater than the requested one. Use
DIV_ROUND_UP()to keep the frequency equal or below the requested one. This way, we can also drop the "if div > 0" check because we know for a fact that div cannot be zero.FWIW, this aligns the CDR2 calculation with the linux driver.
Thanks, that looks alright now. I tested some corner cases, and it seems to do the right thing (TM) now.
Quoted 2 lines
Suggested-by Andre Przywara <[email protected]>Signed-off-by Michael Walle <[email protected]>
Applied to sunxi/master.
Cheers,
Andre.
Quoted 36 lines
--- drivers/spi/spi-sunxi.c | 11 ++++------- 1 file changed, 4 insertions(+), 7 deletions(-)drivers/spi/spi-sunxi.c +4
-7@@ -233,7 +233,7 @@ err_ahb:static void sun4i_spi_set_speed_mode (struct udevice *dev) {struct sun4i_spi_priv *priv =dev_get_priv (dev); -unsigned int div; +unsigned int div, div_cdr2;u32 reg;/* @@ -259,15 +259,12 @@ static void sun4i_spi_set_speed_mode(struct udevice *dev)*/ div =DIV_ROUND_UP (SUNXI_INPUT_CLOCK , priv->freq); + div_cdr2 =DIV_ROUND_UP (div,2 ); reg =readl (SPI_REG (priv,SPI_CCR )); -if ((div /2 ) <= (SUN4I_CLK_CTL_CDR2_MASK +1 )) { - div /=2 ; -if (div >0 ) - div--; - +if (div_cdr2 <= (SUN4I_CLK_CTL_CDR2_MASK +1 )) { reg &= ~(SUN4I_CLK_CTL_CDR2_MASK |SUN4I_CLK_CTL_DRS ); - reg |=SUN4I_CLK_CTL_CDR2 (div) |SUN4I_CLK_CTL_DRS ; + reg |=SUN4I_CLK_CTL_CDR2 (div_cdr2 -1 ) |SUN4I_CLK_CTL_DRS ; }else { div =fls (div -1 );/* The F1C100s encodes the divider as 2^(n+1) */