net: phylib: do not disable autoneg for fixed speeds >= 1G
Subsystems (3)
PATCH 1/1 net: phylib: do not disable autoneg for fixed speeds >= 1G
We have an increasing number of drivers that are forcing auto-negotiation to be enabled for speeds of 1G or faster.
It would appear that auto-negotiation is mandatory for speeds above 100M. In 802.3, Annex 40C's state diagrams seems to imply that mr_autoneg_enable (BMCR AN ENABLE) doesn't affect whether or not the AN state machines work for 1000base-T, and some PHY datasheets (e.g. Marvell Alaska) state that disabling mr_autoneg_enable leaves AN enabled but forced to 1G full duplex.
Other PHY datasheets imply that BMCR AN ENABLE should not be cleared for >= 1G.
Thus, this should be handled in phylib rather than in each driver.
Rather than erroring out, arrange to implement the Marvell Alaska solution but in software for all PHYs: generate an appropriate single-speed advertisement for the requested speed, and keep AN enabled to the PHY driver. However, to avoid userspace API breakage, continue to report to userspace that we have AN disabled.
--- drivers/net/phy/phy_device.c | 34 +++++++++++++++++++++++++--------- 1 file changed, 25 insertions(+), 9 deletions(-)
drivers/net/phy/phy_device.c +25 -9
@@ -2103,22 +2103,20 @@ EXPORT_SYMBOL(phy_reset_after_clk_enable);/** * genphy_config_advert - sanitize and advertise auto-negotiation parameters * @phydev: target phy_device struct +* @advert: auto-negotiation parameters to advertise * * Description: Writes MII_ADVERTISE with the appropriate values, * after sanitizing the values to make sure we only advertise * what is supported. Returns < 0 on error, 0 if the PHY's advertisement * hasn't changed, and > 0 if it has changed. */ -static int genphy_config_advert (struct phy_device *phydev) +static int genphy_config_advert (struct phy_device *phydev, +const unsigned long *advert) {int err, bmsr, changed =0 ;u32 adv; -/* Only allow advertising what this PHY supports */ -linkmode_and (phydev->advertising, phydev->advertising, - phydev->supported); - - adv =linkmode_adv_to_mii_adv_t (phydev->advertising); + adv =linkmode_adv_to_mii_adv_t (advert);/* Setup standard advertisement */ err = phy_modify_changed(phydev, MII_ADVERTISE,
@@ -2141,7 +2139,7 @@ static int genphy_config_advert(struct phy_device *phydev)if (!(bmsr &BMSR_ESTATEN ))return changed; - adv =linkmode_adv_to_mii_ctrl1000_t (phydev->advertising); + adv =linkmode_adv_to_mii_ctrl1000_t (advert); err = phy_modify_changed(phydev, MII_CTRL1000, ADVERTISE_1000FULL | ADVERTISE_1000HALF,
@@ -2365,6 +2363,9 @@ EXPORT_SYMBOL(genphy_check_and_restart_aneg);*/ int __genphy_config_aneg (struct phy_device *phydev,bool changed) { +__ETHTOOL_DECLARE_LINK_MODE_MASK (fixed_advert); +const struct phy_setting *set; +unsigned long *advert;int err; err =genphy_c45_an_config_eee_aneg (phydev);
@@ -2379,10 +2380,25 @@ int __genphy_config_aneg(struct phy_device *phydev, bool changed)else if (err) changed = true; -if (AUTONEG_ENABLE != phydev->autoneg) +if (phydev->autoneg ==AUTONEG_ENABLE ) { +/* Only allow advertising what this PHY supports */ +linkmode_and (phydev->advertising, phydev->advertising, + phydev->supported); + advert = phydev->advertising; + }else if (phydev->speed <SPEED_1000 ) {return genphy_setup_forced (phydev); + }else { +linkmode_zero (fixed_advert); + + set =phy_lookup_setting (phydev->speed, phydev->duplex, + phydev->supported, true); +if (set) +linkmode_set (set->bit, fixed_advert); + + advert = fixed_advert; + } - err =genphy_config_advert (phydev); + err =genphy_config_advert (phydev, advert);if (err <0 )/* error */ return err;else if (err)
Signature · 1 line
2.30.2
kernel test robot
build botkernel test robot noticed the following build errors:
Hi Russell,
kernel test robot noticed the following build errors:
[auto build test ERROR on net-next/main]
url: https://github.com/intel-lab-lkp/linux/commits/Russell-King-Oracle/net-phylib-do-not-disable-autoneg-for-fixed-speeds-1G/20240807-185909 base: net-next/main patch link: https://lore.kernel.org/r/E1sbdxI-0024Eo-HE%40rmk-PC.armlinux.org.uk patch subject: [PATCH net-next] net: phylib: do not disable autoneg for fixed speeds >= 1G config: i386-buildonly-randconfig-004-20240808 (https://download.01.org/0day-ci/archive/20240808/[email protected]/config) compiler: clang version 18.1.5 (https://github.com/llvm/llvm-project 617a15a9eac96088ae5e9134248d8236e34b91b1) reproduce (this is a W=1 build): (https://download.01.org/0day-ci/archive/20240808/[email protected]/reproduce)
If you fix the issue in a separate patch/commit (i.e. not just a new version of the same patch/commit), kindly add following tags
| Reported-by: kernel test robot <[email protected]>
| Closes: https://lore.kernel.org/oe-kbuild-all/[email protected]/
All errors (new ones prefixed by >>):
>> drivers/net/phy/phy_device.c:2124:34: error: passing 'const unsigned long *' to parameter of type 'unsigned long *' discards qualifiers [-Werror,-Wincompatible-pointer-types-discards-qualifiers]
2124 | adv = linkmode_adv_to_mii_adv_t(advert);
| ^~~~~~
include/linux/mii.h:143:60: note: passing argument to parameter 'advertising' here
143 | static inline u32 linkmode_adv_to_mii_adv_t(unsigned long *advertising)
| ^
drivers/net/phy/phy_device.c:2147:39: error: passing 'const unsigned long *' to parameter of type 'unsigned long *' discards qualifiers [-Werror,-Wincompatible-pointer-types-discards-qualifiers]
2147 | adv = linkmode_adv_to_mii_ctrl1000_t(advert);
| ^~~~~~
include/linux/mii.h:218:65: note: passing argument to parameter 'advertising' here
218 | static inline u32 linkmode_adv_to_mii_ctrl1000_t(unsigned long *advertising)
| ^
>> drivers/net/phy/phy_device.c:2401:4: error: call to undeclared function 'linkmode_set'; ISO C99 and later do not support implicit function declarations [-Wimplicit-function-declaration]
2401 | linkmode_set(set->bit, fixed_advert);
| ^3 errors generated.
vim +2124 drivers/net/phy/phy_device.c
2107
2108 /**
2109 * genphy_config_advert - sanitize and advertise auto-negotiation parameters
2110 * @phydev: target phy_device struct
2111 * @advert: auto-negotiation parameters to advertise
2112 *
2113 * Description: Writes MII_ADVERTISE with the appropriate values,
2114 * after sanitizing the values to make sure we only advertise
2115 * what is supported. Returns < 0 on error, 0 if the PHY's advertisement
2116 * hasn't changed, and > 0 if it has changed.
2117 */
2118 static int genphy_config_advert(struct phy_device *phydev,
2119 const unsigned long *advert)
2120 {
2121 int err, bmsr, changed = 0;
2122 u32 adv;
2123
> 2124 adv = linkmode_adv_to_mii_adv_t(advert); 2125
2126 /* Setup standard advertisement */
2127 err = phy_modify_changed(phydev, MII_ADVERTISE,
2128 ADVERTISE_ALL | ADVERTISE_100BASE4 |
2129 ADVERTISE_PAUSE_CAP | ADVERTISE_PAUSE_ASYM,
2130 adv);
2131 if (err < 0)
2132 return err;
2133 if (err > 0)
2134 changed = 1;
2135
2136 bmsr = phy_read(phydev, MII_BMSR);
2137 if (bmsr < 0)
2138 return bmsr;
2139
2140 /* Per 802.3-2008, Section 22.2.4.2.16 Extended status all
2141 * 1000Mbits/sec capable PHYs shall have the BMSR_ESTATEN bit set to a
2142 * logical 1.
2143 */
2144 if (!(bmsr & BMSR_ESTATEN))
2145 return changed;
2146
2147 adv = linkmode_adv_to_mii_ctrl1000_t(advert);
2148
2149 err = phy_modify_changed(phydev, MII_CTRL1000,
2150 ADVERTISE_1000FULL | ADVERTISE_1000HALF,
2151 adv);
2152 if (err < 0)
2153 return err;
2154 if (err > 0)
2155 changed = 1;
2156
2157 return changed;
2158 }
2159
Signature · 2 lines
0-DAY CI Kernel Test Service https://github.com/intel/lkp-tests/wiki
kernel test robot
build botkernel test robot noticed the following build errors:
Hi Russell,
kernel test robot noticed the following build errors:
[auto build test ERROR on net-next/main]
url: https://github.com/intel-lab-lkp/linux/commits/Russell-King-Oracle/net-phylib-do-not-disable-autoneg-for-fixed-speeds-1G/20240807-185909 base: net-next/main patch link: https://lore.kernel.org/r/E1sbdxI-0024Eo-HE%40rmk-PC.armlinux.org.uk patch subject: [PATCH net-next] net: phylib: do not disable autoneg for fixed speeds >= 1G config: arc-randconfig-001-20240808 (https://download.01.org/0day-ci/archive/20240808/[email protected]/config) compiler: arceb-elf-gcc (GCC) 13.2.0 reproduce (this is a W=1 build): (https://download.01.org/0day-ci/archive/20240808/[email protected]/reproduce)
If you fix the issue in a separate patch/commit (i.e. not just a new version of the same patch/commit), kindly add following tags
| Reported-by: kernel test robot <[email protected]>
| Closes: https://lore.kernel.org/oe-kbuild-all/[email protected]/
All error/warnings (new ones prefixed by >>):
drivers/net/phy/phy_device.c: In function 'genphy_config_advert':
>> drivers/net/phy/phy_device.c:2124:41: warning: passing argument 1 of 'linkmode_adv_to_mii_adv_t' discards 'const' qualifier from pointer target type [-Wdiscarded-qualifiers]
2124 | adv = linkmode_adv_to_mii_adv_t(advert);
| ^~~~~~
In file included from include/uapi/linux/mdio.h:15,
from include/linux/mdio.h:9,
from drivers/net/phy/phy_device.c:23:
include/linux/mii.h:143:60: note: expected 'long unsigned int *' but argument is of type 'const long unsigned int *'
143 | static inline u32 linkmode_adv_to_mii_adv_t(unsigned long *advertising)
| ~~~~~~~~~~~~~~~^~~~~~~~~~~
>> drivers/net/phy/phy_device.c:2147:46: warning: passing argument 1 of 'linkmode_adv_to_mii_ctrl1000_t' discards 'const' qualifier from pointer target type [-Wdiscarded-qualifiers]
2147 | adv = linkmode_adv_to_mii_ctrl1000_t(advert);
| ^~~~~~
include/linux/mii.h:218:65: note: expected 'long unsigned int *' but argument is of type 'const long unsigned int *'
218 | static inline u32 linkmode_adv_to_mii_ctrl1000_t(unsigned long *advertising)
| ~~~~~~~~~~~~~~~^~~~~~~~~~~
drivers/net/phy/phy_device.c: In function '__genphy_config_aneg':
>> drivers/net/phy/phy_device.c:2401:25: error: implicit declaration of function 'linkmode_set'; did you mean 'linkmode_subset'? [-Werror=implicit-function-declaration]
2401 | linkmode_set(set->bit, fixed_advert);
| ^~~~~~~~~~~~
| linkmode_subsetcc1: some warnings being treated as errors
vim +2401 drivers/net/phy/phy_device.c
2359
2360 /**
2361 * __genphy_config_aneg - restart auto-negotiation or write BMCR
2362 * @phydev: target phy_device struct
2363 * @changed: whether autoneg is requested
2364 *
2365 * Description: If auto-negotiation is enabled, we configure the
2366 * advertising, and then restart auto-negotiation. If it is not
2367 * enabled, then we write the BMCR.
2368 */
2369 int __genphy_config_aneg(struct phy_device *phydev, bool changed)
2370 {
2371 __ETHTOOL_DECLARE_LINK_MODE_MASK(fixed_advert);
2372 const struct phy_setting *set;
2373 unsigned long *advert;
2374 int err;
2375
2376 err = genphy_c45_an_config_eee_aneg(phydev);
2377 if (err < 0)
2378 return err;
2379 else if (err)
2380 changed = true;
2381
2382 err = genphy_setup_master_slave(phydev);
2383 if (err < 0)
2384 return err;
2385 else if (err)
2386 changed = true;
2387
2388 if (phydev->autoneg == AUTONEG_ENABLE) {
2389 /* Only allow advertising what this PHY supports */
2390 linkmode_and(phydev->advertising, phydev->advertising,
2391 phydev->supported);
2392 advert = phydev->advertising;
2393 } else if (phydev->speed < SPEED_1000) {
2394 return genphy_setup_forced(phydev);
2395 } else {
2396 linkmode_zero(fixed_advert);
2397
2398 set = phy_lookup_setting(phydev->speed, phydev->duplex,
2399 phydev->supported, true);
2400 if (set)
> 2401 linkmode_set(set->bit, fixed_advert);
2402
2403 advert = fixed_advert;
2404 }
2405
2406 err = genphy_config_advert(phydev, advert);
2407 if (err < 0) /* error */
2408 return err;
2409 else if (err)
2410 changed = true;
2411
2412 return genphy_check_and_restart_aneg(phydev, changed);
2413 }
2414 EXPORT_SYMBOL(__genphy_config_aneg);
2415
Signature · 2 lines
0-DAY CI Kernel Test Service https://github.com/intel/lkp-tests/wiki